Yamaha CRX-E300 Инструкция по применению

Категория
Ресиверы
Тип
Инструкция по применению
CRX-E300
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
CD Receiver
Ampli-Tuner CD
GB
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Malaysia V921790
CRX-E300
0101CRXE300(M).H1-H4.E 02.5.24, 3:30 PM1
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this unit in a well ventilated, cool, dry, clean
place away from direct sunlight, heat sources, vibration,
dust, moisture or cold. In a cabinet, allow about 10 cm
(4 in.) of free space all around this unit for adequate
ventilation.
3 Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes
from cold to hot, nor locate this unit in an environment
with high humidity (i.e., a room with a humidifier) to
prevent condensation inside this unit, which may cause
an electrical shock, fire, damage to this unit, and/or
personal injury.
5 Avoid installing this unit in a location where foreign
objects may fall onto this unit or where this unit may be
exposed to liquid dripping or splashing. On the top of
this unit, do not place:
Other components, as they may cause damage and/or
discoloration on the surface of this unit.
Burning objects (i.e., candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall, spilling
the liquid and causing an electrical shock to the user
and/or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use excessive force on switches, knobs and/or
cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Use only the voltage specified on this unit. Using this
unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. YAMAHA will not be held responsible for any
damage resulting from use of this unit with a voltage
other than as specified.
13 To prevent damage by lightning, disconnect the power
cord from the wall outlet during an electrical storm.
14 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any service
is needed. The cabinet should never be opened for any
reason.
15 When not planning to use this unit for long periods of
time (i.e., vacation), disconnect the AC power plug from
the wall outlet.
16 Be sure to read the “Troubleshooting” section on
common operating errors before concluding that this
unit is faulty.
17 Before moving this unit, press STANDBY/ON to set the
unit in standby mode, then disconnect the AC power
plug from the wall outlet.
CAUTION: READ THIS BEFORE OPERATING THIS UNIT
18 VOLTAGE SELECTOR (China and General models
only)
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local main voltage BEFORE
plugging into the AC main supply. Voltages are 110/120/
220/240 V AC, 50/60 Hz.
To reduce the risk of fire or electric shock, do not
expose this appliance to rain or moisture.
The unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off. This state is called the standby
mode. In this state, this unit is designed to consume a
very small quantity of power.
CAUTION FOR CARRYING THE UNIT
Before carrying the unit, first remove the disc from
the unit, press STANDBY/ON to turn the unit off,
then disconnect the AC power plug from the wall
outlet.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
IMPORTANT:
The wires in the mains lead are coloured in accordance
with the following code:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows: The wire which is coloured BLUE
must be connected to the terminal which is marked
with the letter N or coloured BLACK. The wire which
is coloured BROWN must be connected to the terminal
which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
For U.K. customers
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described above.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous
if engaged in a live socket outlet.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
Laser component in this product is capable of
emitting radiation exceeding the limit for Class 1.
0102CRXE300(M).Cau.E 02.5.24, 3:34 PM2
1
English
FEATURES
<Receiver>
Minimum RMS output power per channel
25 W + 25 W
(6, 1 kHz, 0.1% THD)
Full operation system remote control
40-station FM/AM preset tuning
Multi-function RDS reception
SUBWOOFER output terminal
<CD player>
S-bit DAC and 8fs digital filter
Optical digital output
Random, repeat, and program play
CD TEXT display
Copy time control
CD-RW compatible
The CD receiver CRX-E300 is the main unit of the YAMAHA Piano Craft Series. You can upgrade the system by adding
the cassette deck (KX-E300) and MD recorder (MDX-E300)*.
* The cassette deck (KX-E300) and MD recorder (MDX-E300) may not be available for some areas.
SUPPLIED ACCESSORIES ....................... 2
CD PREVENTIVE CARE .......................... 2
NAMES OF BUTTONS AND CONTROLS
Front panel ............................................................ 3
Display ..................................................................3
Remote control ..................................................... 4
GETTING STARTED
Remote control ..................................................... 5
Connecting the speakers and antennas .................6
Connecting other components .............................. 7
Setting the clock ...................................................8
Adjusting the brightness of the display ................8
LISTENING TO A SOURCE ...................... 9
TUNING ............................................... 10
Presetting stations ............................................... 11
RECEIVING RDS STATIONS
Receiving RDS data............................................ 12
PTY SEEK mode................................................ 13
Optional settings for RDS functions................... 14
CD OPERATIONS
Playing a disc...................................................... 15
Selecting the time display and CD TEXT .......... 16
Random-sequence play....................................... 16
Repeat play ......................................................... 17
Program play ...................................................... 17
USING THE BUILT-IN TIMER
Before using the timer ........................................ 19
Timer play and recording ................................... 19
Sleep timer .......................................................... 20
SYSTEM CONTROL
Controlling other components with the remote
control ................................................................. 21
Before recording ................................................. 22
Dubbing setting .................................................. 22
CD synchronized recording ................................ 22
Copy time control ............................................... 23
ADDITIONAL INFORMATION
Troubleshooting .................................................. 24
Specifications...................................................... 26
CONTENTS
0103CRXE300(M).01-07.E 02.5.24, 3:34 PM1
2
SUPPLIED ACCESSORIES
Remote control
AM loop antenna
Indoor FM antenna
Batteries (AA, R6, UM-3)
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
FREQ
/
RDS MODE
PTY SEEK
START
REP
RANDOM
PROG
ABC
TEXT
/
TIME
R. TIME
DE
TAPE
DIRECTION
PRESET
TUNER
PRESET
MD CD TAPE
AUX
MD
REC
/
PAUS E
TAPE
REC
/
PAUSE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
After unpacking, check that the following parts are contained.
CD PREVENTIVE CARE
No!
Compact discs are not affected by small particles of
dust or fingerprints on their playing surface, but even so
they should be kept clean. Wipe by using a clean, dry
cloth. Do not wipe with a circular motion; wipe straight
outward from the center.
Do not try to clean the discs surface by using any type
of disc cleaner, record spray, antistatic spray or liquid,
or any other chemical-based liquid, because such
substances might irreparably damage the discs surface.
Do not expose discs to direct sunlight, high temperature
or high humidity for a long period of time, because
these might warp or otherwise damage the disc.
This compact disc player is designed for use with
following types of disc only. Never attempt to load any
other type of disc into the unit. The unit will also play
8-cm (3-inch) compact discs.
Be sure to use only CD-R and CD-RW discs made by
reliable manufacturers.
Some discs cannot be played depending on the disc
characteristics or recording conditions (copyright-
protected in a particular way, etc.).
Compact discs are not subjected to wear during play,
but damage to the disc surface when the disc is being
handled can adversely affect the discs play.
Do not use cleaning discs or warped discs. All of these
could damage the unit.
To prevent a malfunction of this unit
Do not use any non standard shaped CD (heart, etc.)
available on the market, because it may damage the
unit.
Do not use a CD with tape, seals, or paste on it, because
damage to the unit may result.
(U.S.A., Canada, China,
Korea and General
models)
(Europe, U.K., and
Australia models)
(Playback only)
0103CRXE300(M).01-07.E 02.5.24, 3:34 PM2
3
English
NAMES OF BUTTONS AND CONTROLS
Front panel
1 STANDBY/ON (P.9)
2 TIMER indicator (P.19)
3 DISPLAY (P.8,19)
4 TIME ADJ/MEMORY (P.8,11)
5 TIMER/AUTO/MAN’L (P.10,19)
6 PRESET/BAND (P.10)
7 Display (P.3)
8 PRESET/TUNING / (P.10)
When TUNER is selected as an input
source
$/!// (P.15)
When CD is selected as an input
source
9 VOLUME (P.9)
0 PHONES (P.9)
q Disc tray
w BASS (P.9)
e TREBLE (P.9)
r BALANCE (P.9)
t (Open/Close) (P.15)
y & (Stop) (P.15)
u INPUT (P.9)
i ^ (Play/Pause) (P.15)
BALANCE
INPUT
VOLUME
L
R
TREBLEBASS
PHONES
STANDBY/ON
TIMER DISPLAY MEMORY
NATURAL SOUND CD RECEIVER CRX-E300
AUTO/MAN'L
PRESET/BAND
TIMER HOUR MIN
MIN MAX
PRESET/TUNING
TIMER ADJ
+–+
12 345678 9
0
qw e rtyui
Display
TIMER
SLEEP
STEREO AUTO RDS PS RT CT F PROG A B
RANDOM
SREPPTY
MEMORY
TUNED PTY HOLD CD-TEXTTITLEARTIST TRACK
PRESET
1
q
we r t y
23456 7890
1 Multi information display
2 PRESET indicator (P.11)
3 STEREO indicator (P.10)
4 AUTO indicator (P.10)
5 RDS indicator (P.12)
6 RDS mode indicators (P.12)
7 PTY HOLD indicator (P.13)
8 REP S/F (repeat single/full) indicator
(P.17)
9 PROG (program) indicator (P.17)
0 RANDOM indicator (P.16)
q A B Tape side indicator (P.23)
w TIMER indicator (P.19)
e SLEEP indicator (P.20)
r MEMORY indicator (P.11)
t TUNED indicator (P.10)
y CD Text indicators (P.16)
0103CRXE300(M).01-07.E 02.5.24, 3:34 PM3
4
Remote control
1 POWER (P.9)
2 Preset numbers (18)
*
(P.11)
3 FREQ/RDS
*
(P.12)
4 PTY SEEK MODE
*
(P.13,14)
5 PTY SEEK START
*
(P.13,14)
6 A/B/C/D/E
*
(P.11)
7 PRESET /
*
(P.11)
8 TUNER (P.11)
9 MD (MDX-E300) (P.21)
0 TAPE (KX-E300) (P.21)
q CD (P.15)
w AUX (The equipment connected to the AUX
terminal)
e SLEEP (P.20)
r DISPLAY (P.19)
t VOLUME + (P.9)
* When TUNER is selected as an input source
Note
8w are input selectors for each component.
When CD is selected as an input source
1 POWER (P.15)
2 Numeric buttons (P.15)
+100 button is used when operating
MDX-E300.
3 REP (Repeat) (P.17)
4 PROG (Program) (P.17)
5 RANDOM (Random) (P.16)
6 TEXT/TIME (P.16)
7 ^ (Play/Pause) (P.15)
8 $ ! (Skip/Seach backward) (P.15)
9 (Skip/Seach forward) (P.15)
0 & (Stop) (P.15)
q CD input (P.15)
NAMES OF BUTTONS AND CONTROLS
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
REP
RANDOM
PROG
ABC
TEXT
/
TIME
R. TIME
DE
TAPE
DIRECTION
PRESET
TUNER
PRESET
MD CD TAPE
AUX
MD
REC
/
PAUSE
TAPE
REC
/
PAUSE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
FREQ
/
RDS MODE
PTY SEEK
START
1,1
2,2
8
0
5
4
q,q
w
r
t
6
3
7
9
e
43
6
5
7
98
0
0103CRXE300(M).01-07.E 02.5.24, 3:34 PM4
5
English
Remote control
This remote control controls a whole system: not only
CRX-E300 but also a cassette deck (KX-E300) and MD
recorder (MDX-E300) that enhance your system.
Battery installation
1 Remove the battery compartment cover.
2 Insert batteries into the battery compartment.
3 Replace the battery compartment cover.
Battery replacement
If you find that the remote control must be used closer to
the main unit than usual, the batteries are weak. Replace
batteries with new ones.
Notes
Use only AA, R6, UM-3 batteries for replacement.
Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
Remove the batteries if the remote control will not be used for
an extended period of time.
If batteries leak, dispose of them immediately. Avoid touching
the leaked material or letting it come in contact with clothing,
etc. Clean the battery compartment thoroughly before
installing new batteries.
Remote control operation range
Notes
There should be no large obstacles between the remote control
and the main unit.
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp, etc.),
it might cause the remote control not to work correctly. In this
case, reposition the main unit to avoid direct lighting.
Removing the protection sheet
The remote control is shipped with a protection sheet to
prevent the surface from being scratched during
transportation.
When removing the sheet, first put adhesive tape on an
edge of the remote control so that the tape sticks to the
sheet. Then peel the sheet off with the tape.
Note
Do not scratch the remote control surface when peeling the
sheet off.
GETTING STARTED
2
1
3
P
O
W
E
R
1
1
2
2
3
3
4
4
7
7
8
8
9
5
5
6
6
P
O
W
E
R
1
1
2
2
3
3
4
4
7
7
8
8
9
5
5
6
6
BALANCE
INPUT
VOLUME
L
R
TREBLEBASS
PHONES
STANDBY/ON
TIMER DISPLAY MEMORY
NATURAL SOUND CD RECEIVER CRX-E300
AUTO/MAN'L
PRESET/BAND
TIMER HOUR MIN
MIN MAX
PRESET/TUNING
TIMER ADJ
+ +
30°
30°
Remote control
sensor
Within approximately
6 m (20 feet)
0103CRXE300(M).01-07.E 02.5.24, 3:34 PM5
6
Connecting the speakers and antennas
Never plug the AC power cord to the wall outlet until all connections are
completed.
Follow the steps as shown below to connect the system using the supplied cords and accessories. Be sure all connections are
made correctly, that is to say L (left) to L, R (right) to R, + to + and “–” to “–”.
1 Connect the Speakers.
1 Unscrew the knob.
2 Remove approx. 10 mm (4) of insulation from
each of the speaker wires and insert the bare wire
into the terminal.
3 Tighten the knob to secure the wire.
2 Connect the AM Antenna.
Set up the AM loop antenna, then connect it.
3 Connect the FM Antenna.
4 Connect the AC power cord to a wall outlet.
Notes
Use external FM/AM antennas if you need better reception.
Consult your dealer.
The AM loop antenna should be placed apart from the main
unit. The antenna may be hung on a wall.
To connect the subwoofer (optional)
You can reinforce the bass frequencies by adding a
subwoofer (optional).
Connect the SUBWOOFER OUT terminal of the unit to
the INPUT terminal of the subwoofer.
1
3 FM antenna
2 AM loop antenna
Right speaker Left speaker
GETTING STARTED
Red: positive(+)
Black: negative()
GND AM ANT
1
2
3
4 To wall outlet
MD
TAPE
IN
OUT
IN
IN
OUT
AUX
D
A
B
L
R
C
SYSTEM CONNECTOR
OUT
SUBWOOFER
OUT
DIGITAL
OPTICAL
SPEAKERS
RL
6
MIN. /SPEAKER
CLASS 2 WIRING
FM ANT
GND – AM ANT
75
UNBAL.
FM ANT
75 UNBAL
0103CRXE300(M).01-07.E 02.5.24, 3:34 PM6
7
English
OUT
A
L
IN
B
R
SYSTEM
CONNECTOR
OUT
FM ANT
GND AM ANT
SPEAKERS
RL
75
UNBAL.
6
MIN. /SPEAKER
CLASS 2 WIRING
SYSTEM CONNECTOR
SUBWOOFER
DIGITAL
OUT
OPTICAL
IN
TAPE
OUT
IN
IN
OUT
AUX
D
A
B
L
R
C
MD
ANALOG DIGITAL
OPTICAL
IN
L
D
OUT
1
IN
2
R
C
SYSTEM
CONNECTOR
<MDX-E300>
<KX-E300>
<CRX-E300>
Connecting other components
To enhance your system, you can connect other components. Refer to the instructions of each component.
Connecting KX-E300 and MDX-E300
GETTING STARTED
1 Connect Å to Å, and ı to ı (for connecting KX-E300), Ç to Ç and Î to Î (for connecting MDX-E300) using
audio pin cable.
2 Connect the DIGITAL OPTICAL OUT jack of CRX-E300 to the DIGITAL OPTICAL IN jack of MDX-E300.
Take off the covers of the optical cable plug, the DIGITAL OPTICAL OUT jack, and the DIGITAL OPTICAL IN
jack before making digital connections. Be sure to replace the jacks cover when the jack on the rear panel is not being
used, in order to protect from dust.
3 Connect an external component to the AUX jack of CRX-E300.
4 Connect CRX-E300 to MDX-E300 and MDX-E300 to KX-E300 with the system control cables.
The connection using the SYSTEM CONNECTOR jack allows you to control this unit as well as the connected
components of YAMAHA Piano Craft series.
If your system does not include MDX-E300, connect CRX-E300 and KX-E300 directly.
5 AC OUTLET
Connect the AC power plug of MDX-E300 to the AC outlet of CRX-E300. Then connect the plug of KX-E300 to the
AC outlet of MDX-E300.
If your system does not include MDX-E300, connect the plug of KX-E300 to the AC outlet of CRX-E300.
Caution
Never turn CRX-E300 on until all connections between components have been completed.
Never connect or disconnect the system control cable and/or power cord while the system components are turned on.
2
5
3
4
Optical cable (EIA standard)
(commercially available)
To wall
outlet
Audio pin cables
System
control cable
(supplied with
KX-E300)
System control cable
(supplied with
MDX-E300)
1
As this terminal is used for an
examination in the factory, do not
connect any equipment to this terminal.
0103CRXE300(M).01-07.E 02.5.24, 3:34 PM7
8
Setting the clock
You must set the clock before you use the timer functions.
The clock is based on a 24-hour system.
1 Turn on the power by pressing STANDBY/ON on
the front panel, or POWER on the remote control.
2 While the power is on, press DISPLAY to display
the time.
3 While holding TIME ADJ, press HOUR to set the
hour.
If you want to move the time in the reverse
direction, press HOUR while holding TIME ADJ
and PRESET/BAND.
4 While holding TIME ADJ, press MIN to set the
minutes.
If you want to move the time in the reverse
direction, press MIN while holding TIME ADJ
and PRESET/BAND.
To display the clock
Press DISPLAY.
The current time appears for about 8 seconds, then the
normal display returns. Some buttons and controls may
not work while the current time is displayed.
Note
In the event of a power failure or when the AC power cord is
disconnected for more than five minutes, you must reset the
clock.
Adjusting the brightness
of the display
You can adjust the brightness of the display. If you have
connected cassette deck (KX-E300) and/or MD recorder
(MDX-E300) to this unit, the brightness of the displays is
automatically adjusted to that of this unit.
Press and hold DISPLAY for about two seconds so that
Dimmer ±0 appears on the display. While holding
DISPLAY, turn INPUT clockwise to increase or
counterclockwise to decrease brightness.
Control Range: ±0 to 6 (Preset value: ±0)
INPUT
DISPLAY
BALANCE
INPUT
VOLUME
L
R
TREBLEBASS
PHONES
STANDBY/ON
TIMER DISPLAY MEMORY
NATURAL SOUND CD RECEIVER CRX-E300
AUTO/MAN'L
PRESET/BAND
TIMER HOUR MIN
MIN MAX
PRESET/TUNING
TIMER ADJ
+ +
HOUR
DISPLAY
PRESET/BANDTIME ADJ
MIN
BALANCE
INPUT
VOLUME
L
R
TREBLEBASS
PHONES
STANDBY/ON
TIMER DISPLAY MEMORY
NATURAL SOUND CD RECEIVER CRX-E300
AUTO/MAN'L
PRESET/BAND
TIMER HOUR MIN
MIN MAX
PRESET/TUNING
TIMER ADJ
+ +
GETTING STARTED
STANDBY/ON
0104CRXE300(M).08-09.E 02.5.24, 3:34 PM8
English
9
LISTENING TO A SOURCE
1 Set the volume to MIN by turning VOLUME.
2 Turn on the power by pressing STANDBY/ON on
the front panel, or POWER on the remote control.
Piano Craft series components that have correct
system connections made to CRX-E300 can be
controlled to turn to the on or standby mode by
CRX-E300. However, once the connected
components are turned to the standby mode with
their respective STANDBY/ON button, they
cannot be controlled by CRX-E300 STANDBY/
ON button.
3 Select the desired input source by turning INPUT so
that the source appears on the display.
When you operate the component connected to the
AUX terminal, turn INPUT to select AUX.
4 Play the source. (Refer to the owners manual
supplied with each selected component.)
5 Adjust the volume level by turning VOLUME on the
front panel or pressing VOLUME + on the remote
control.
6 If desired, adjust BASS, TREBLE, and BALANCE.
BASS: Turn this control clockwise to increase (or
counterclockwise to decrease) the low frequency
response.
TREBLE: Turn this control clockwise to increase (or
counterclockwise to decrease) the high frequency
response.
BALANCE: Adjust the balance of the output volume
from the left and right speakers to compensate for
sound imbalance caused by the speaker location or
listening room conditions.
When you use headphones
Connect the headphones to the PHONES jack. You can
listen to the sound to be output from the main speakers
through the headphones.
When you have finished using this
unit
Press STANDBY/ON on the front panel again or
POWER on the remote control to set this unit to the
standby mode.
STANDBY appears for a moment on the display.
Auto standby function
This unit will be put automatically into the standby mode
under the following conditions:
A component connected with a system control cable is
selected as an input source.
The component connected to this unit is in stop mode
and not operated for 30 minutes.
POWER
VOLUME –/+
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
FREQ
/
RDS MODE
PTY SEEK
START
REP
RANDOM
PROG
ABC
TEXT
/
TIME
R. TIME
DE
TAPE
DIRECTION
PRESET
TUNER
PRESET
MD CD TAPE
AUX
MD
REC
/
PAUSE
TAPE
REC
/
PAUSE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
VOLUMESTANDBY/ON
INPUTBALANCE
TREBLE
BASSPHONES
BALANCE
INPUT
VOLUME
L
R
TREBLEBASS
PHONES
STANDBY/ON
TIMER DISPLAY MEMORY
NATURAL SOUND CD RECEIVER CRX-E300
AUTO/MAN'L
PRESET/BAND
TIMER HOUR MIN
MIN MAX
PRESET/TUNING
TIMER ADJ
+ +
This chapter explains the basic operations common to
tuning, playing CD and other connected components.
0104CRXE300(M).08-09.E 02.5.24, 3:34 PM9
10
TUNING
Automatic tuning
1 Select TUNER by turning INPUT so that the
frequency of a radio station appears in the display.
2 Press PRESET/BAND to select the reception band.
Do not select the preset tuning mode (in which
PRESET appears on the display).
3 Press AUTO/MANL so that AUTO appears in the
display.
4 Press PRESET/TUNING (for a higher
frequency) or
(for a lower frequency).
5 The unit starts searching for a station.
When the unit finds a station, the unit stops searching
and TUNED appears on the display.
6 If the located station is not the one you want, repeat
steps 4 and 5 until a station you want is tuned.
Notes
If automatic tuning search does not find the desired station, try
manual tuning as described next.
When an FM stereo broadcast with sufficient signal strength is
received, STEREO appears on the display and you can listen
to stereo sound.
You can find radio stations automatically and manually.
Manual tuning
1 Follow steps 1 and 2 described in Automatic
tuning.
2 Press AUTO/MANL so that AUTO disappears
from the display.
3 Press PRESET/TUNING (for a higher
frequency) or
(for a lower frequency) to select
your desired station.
Each time you press PRESET/TUNING or
, the frequency changes step by step.
STEREO AUTO
TUNED
PRESET/TUNING /
PRESET/BAND
BALANCE
INPUT
VOLUME
L
R
TREBLEBASS
PHONES
STANDBY/ON
TIMER DISPLAY MEMORY
NATURAL SOUND CD RECEIVER CRX-E300
AUTO/MAN'L
PRESET/BAND
TIMER HOUR MIN
MIN MAX
PRESET/TUNING
TIMER ADJ
+ +
INPUT
AUTO/MANL
0105CRXE300(M).10-11.E 02.5.24, 3:34 PM10
11
English
TUNING
English
To preset stations manually
1 Tune in a desired station.
(Refer to the previous page for the tuning procedure.)
2 Press MEMORY.
3 Within about 5 seconds, use PRESET/TUNING /
to select a desired preset number. Continue
pressing PRESET/TUNING
/ to select the
group of the preset stations (A, B, C, D, and E).
4 Press MEMORY.
•“MEMORY, PRESET, and preset number will
appear on the display.
5 Repeat steps 1 to 4 until all desired stations are
preset.
Presetting stations
The unit can preset station frequencies selected by
Automatic tuning or Manual tuning. Up to 40 stations can
be stored. With this function, you can select any desired
station by pressing the corresponding preset station
number.
Notes
A new setting can be preset in place of a previous one.
The preset stations are retained for a week after you disconnect
the AC power cord or a power failure occurs.
To preset stations automatically
1 Select TUNER as input source by turning INPUT.
2 Press MEMORY for about 2 seconds.
The unit starts presetting stations, AUTO and
MEMORY will flash on the display.
Received stations are stored to A1, A2...A8 sequentially.
After 40 stations or all FM and AM stations are stored, the
display will show the preset station A1.
To recall a preset station
Press TUNER and select the desired number by pressing
PRESET/BAND and PRESET/TUNING
/ on the
front panel or PRESET
/ , A/B/C/D/E and 18 on
the remote control. Press and hold PRESET/TUNING
/ (or PRESET / on the remote control) to
switch the preset group (AE).
INPUTPRESET/BANDMEMORY
18
A/B/C/D/E
TUNER
PRESET /
BALANCE
INPUT
VOLUME
L
R
TREBLEBASS
PHONES
STANDBY/ON
TIMER DISPLAY MEMORY
NATURAL SOUND CD RECEIVER CRX-E300
AUTO/MAN'L
PRESET/BAND
TIMER HOUR MIN
MIN MAX
PRESET/TUNING
TIMER ADJ
+ +
PRESET/TUNING /
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
FREQ
/
RDS MODE
PTY SEEK
START
REP
RANDOM
PROG
ABC
TEXT
/
TIME
R. TIME
DE
TAPE
DIRECTION
PRESET
TUNER
PRESET
MD CD TAPE
AUX
MD
REC
/
PAUSE
TAPE
REC
/
PAUSE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
STEREO
MEMORY
TUNED
PRESET
STEREO
MEMORY
TUNED
PRESET
The arrow will appear for a second when
it is preset.
0105CRXE300(M).10-11.E 02.5.24, 3:34 PM11
12
Receiving RDS data
RDS (Radio Data System) is a data transmission system
by FM stations in many countries. Stations using this
system transmit an inaudible stream of data in addition to
the normal radio signal. RDS data contains various types
of information, such as PS (Program Service), PTY
(Program Type), RT (Radio Text), and CT (Clock Time).
1 Tune in the FM station.
2 Press FREQ/RDS to choose the mode. Each time
you press FREQ/RDS, the type changes as follows:
FREQ/RDS
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
FREQ
/
RDS MODE
PTY SEEK
START
REP
RANDOM
PROG
ABC
TEXT
/
TIME
R. TIME
DE
TAPE
DIRECTION
PRESET
TUNER
PRESET
MD CD TAPE
AUX
MD
REC
/
PAUSE
TAPE
REC
/
PAUSE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
PS
The name of the RDS station being received is displayed.
If the unit cannot find a station with PS data, the unit stops
searching and NO PS appears on the display.
PTY
The type of the program on the RDS station now being
received is displayed. You can make this unit search for a
station which is broadcasting a program of a desired
program type. (Refer to PTY program mode in the next
section for details.)
RT
Information about the program (such as the title of the
song, name of the singer, etc.) on the RDS station being
received is displayed by a maximum of 64 alphanumeric
characters, including the umlaut symbol. If other
characters are used in the RT data, they are displayed with
an under-bar.
If the unit cannot find a station with RT data, the unit stops
searching and NO RT appears on the display.
CT
Current time is displayed.
If the unit cannot find a station with CT data, the unit stops
searching and NO CT appears on the display.
Notes
RDS may not work properly if the station you are tuned to is
not transmitting the RDS signal properly or if the signal
strength is weak.
Some FM stations do not offer RDS service. Of those that do,
not all provide the same types of services. The types provided
by the received RDS station are dimmed on the display. Check
with your local radio stations for details on RDS services in
your area.
RDS PS
RDS PTY
RDS CT
RECEIVING RDS STATIONS
0106CRXE300(M).12-14.E 02.5.24, 3:34 PM12
13
Playing CDsGetting Started
RECEIVING RDS STATIONS
English
PTY SEEK mode
You can locate a desired station by selecting a program
type. The unit searches all preset stations into the type of
programs currently being broadcast from the RDS
stations.
To locate a station
1 Tune in the FM station.
2 Press PTY SEEK MODE once so that PTY and a
PTY program flashes on the display.
3 Within about 20 seconds, press PRESET /
repeatedly until the desired program type appears on
the display.
4 Within about 20 seconds, press PTY SEEK START.
If a station broadcasting the selected program type
is found, the unit stops searching and the Program
Service name appears on the display.
PTY HOLD appears on the display.
5 Repeat step 4 until the desired station is located.
If there is no station broadcasting the program type
you select, NO PTY appears on the display, then
the Program Service name or frequency appears on
the display.
List of PTY (Program Type)
PTY SEEK MODE
PRESET /
PTY SEEK START
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
FREQ
/
RDS MODE
PTY SEEK
START
REP
RANDOM
PROG
ABC
TEXT
/
TIME
R. TIME
DE
TAPE
DIRECTION
PRESET
TUNER
PRESET
MD CD TAPE
AUX
MD
REC
/
PAU SE
TAPE
REC
/
PAU SE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
PTY
RDS PTY
PTY HOLD
PRESET
NEWS
AFFAIRS
INFO
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
VARIED
POP M
ROCK M
M.O.R. M
LIGHT M
CLASSICS
OTHER M
News
Current Affairs
General Information
Sports
Education
Drama
Culture
Science
Light Entertainment
Pops
Rock
Middle of the Road
Music (Easy-listening)
Light Classics
Serious Classics
Other Music
0106CRXE300(M).12-14.E 02.5.24, 3:34 PM13
14
Optional settings for
RDS functions
The tuner has the following functions which make use of
the RDS data service. These are originally in operation
ON. However, you can turn these functions OFF, if so
desired.
1 Select the FM band by pressing TUNER.
2 Press DISPLAY to display the current time.
3 Press FREQ/RDS.
4 Each time you press PTY SEEK MODE the display
will change as follows:
1. CT = CLOCK (ON/OFF)
The tuner corrects the time of the built-in clock
automatically by synchronizing it with the CT
data on the RDS station being received.
If you receive an RDS station of some other
country, the built-in clock is synchronized with
the time setting of the country.
If the built-in clock is not yet set for the current
time or reset due to a power failure, etc., it will be
set for the time of the CT data automatically,
whether this setting is ON or OFF.
2. LOCAL = CT (ON/OFF)
If the RDS station being received employs the
local time (summer time, etc.) data service, its
time is displayed in the CT mode.
3. A.M. = RDS (ON/OFF)
RDS stations are searched instead of all FM
stations by the automatic preset tuning operation
when the setting is ON. (Refer to page 11.)
4. RT SPEED: ±0
Changes the scrolling speed of the radio text
decreasing the value and, in turn, reducing the
speed.
Control Range: ±0 to ±3 (Preset value: ±0)
5 Choose the function ON or OFF by pressing PTY
SEEK START, confirming it in the display. Press
PTY SEEK START repeatedly to change the value
for RT SPEED.
If there is no operation for about 20 seconds, this
mode is cancelled and turns into the frequency
display. If the station has PS data, it turns into the
PS mode.
6 Press FREQ/RDS again to restore the frequency
display mode.
PTY SEEK MODE
PTY SEEK STARTFREQ/RDS
TUNER
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
FREQ
/
RDS MODE
PTY SEEK
START
REP
RANDOM
PROG
ABC
TEXT
/
TIME
R. TIME
DE
TAPE
DIRECTION
PRESET
TUNER
PRESET
MD CD TAPE
AUX
MD
REC
/
PAUSE
TAPE
REC
/
PAUSE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
DISPLAY
RECEIVING RDS STATIONS
0106CRXE300(M).12-14.E 02.5.24, 3:34 PM14
15
English
1 Press STANDBY/ON to turn on this unit.
2 Press CD on the remote control or turn to CD using
the input knob.
Playing a disc
3 Press to open the disc tray, and place a CD on the
tray.
4 Press ^ to start play.
This unit starts play.
To pause play
Press ^.
To resume play, press ^ again.
To stop play
Press &.
To eject the CD
Press to open the disc tray, and remove the CD from
the tray.
To play a specific track on the disc
(Skip)
Direct play
Select a desired track using the numeric button.
(Example: To select 35, press +10 three times so that
3 _ appears in the display, then press 5.)
Skip play
Press / to skip forward or $/! to skip
backward. Press once for each track to be skipped.
Notes
You cannot enter a number that is higher than the last track
number on the disc.
These operations can also be performed when the unit is in the
pause or stop mode.
During stop mode, if / or $/! is pressed, the
track number successively changes to higher numbers (or
lower numbers).
To advance or reverse playback
rapidly (Search)
Press and hold / to advance playback rapidly, and
$/! to reverse playback rapidly.
Note
This unit cannot play a CD-R or CD-RW disc unless the disc is
finalized. Please make sure to finalize the disc on the CD
recorder before playing on this unit.
^
&
^&
/$/!
$ !/
STANDBY/ON
POWER
CD
Numeric
buttons
BALANCE
INPUT
VOLUME
L
R
TREBLEBASS
PHONES
STANDBY/ON
TIMER DISPLAY MEMORY
NATURAL SOUND CD RECEIVER CRX-E300
AUTO/MAN'L
PRESET/BAND
TIMER HOUR MIN
MIN MAX
PRESET/TUNING
TIMER ADJ
+ +
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
FREQ
/
RDS MODE
PTY SEEK
START
REP
RANDOM
PROG
ABC
TEXT
/
TIME
R. TIME
DE
TAPE
DIRECTION
PRESET
TUNER
PRESET
MD CD TAPE
AUX
MD
REC
/
PAU SE
TAPE
REC
/
PAU SE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
CD OPERATIONS
0107CRXE300(M).15-18.E 02.5.24, 3:35 PM15
16
Each time you press TEXT/TIME, the display changes as
follows:
Note
The disc title, artist names, or track names may not be
displayed with some CD TEXT discs. In this case, (NO
ENTRY) appears on the display for about two seconds and
then go back to the time display.
Press RANDOM.
•“RANDOM indicator lights up on the display.
The unit starts random sequence play.
To cancel random-sequence play
mode
Press & or RANDOM.
•“RANDOM disappears from the display.
Notes
This feature will not function during programming, or during
programmed play.
If / is pressed during random-sequence play, the next
randomly programmed track will be played.
If $/! is pressed, play will return to the beginning of the
current track.
Total remaining time on the disc will not be displayed during
random-sequence play.
Random-sequence play
The unit can play all the tracks in a random sequence.
RANDOM
Selecting the time
display and CD TEXT
You can select any of four time displays by pressing
TEXT/TIME. When you play a CD with CD TEXT, the
disc title, artist name, and track name are also displayed.
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
FREQ
/
RDS MODE
PTY SEEK
START
REP
RANDOM
PROG
ABC
TEXT
/
TIME
R. TIME
DE
TEXT/TIME
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
FREQ
/
RDS MODE
PTY SEEK
START
REP
RANDOM
PROG
ABC
TEXT
/
TIME
R. TIME
DE
Elapsed time of the
current track
•“CD-TEXT appears on the display if
a CD has CD TEXT.
Total remaining time of
the disc
Total disc play time
Remaining time of the
current track
Disc title
Artist name
Track name
The current track number
CD OPERATIONS
0107CRXE300(M).15-18.E 02.5.24, 3:35 PM16
17
English
SINGLE REPEAT
The current track is played repeatedly.
FULL REPEAT
The current disc is played repeatedly.
In random-sequence play mode, all randomly
sequenced tracks are played repeatedly in each-time-
different order.
To cancel repeat play mode
Press REP successively until REP S and REP F
disappear from the display.
1 Press & to stop the unit.
2 Press PROG.
3 Use the numeric buttons to select a track number
until the desired track number appears on the display.
4 Repeat step 3 to program more tracks. You can select
the same track again.
5 Press ^ to start program play.
Program play
By creating a program, you can enjoy listening to your
favourite tracks in any desired order. As many as 20
tracks can be programmed in sequence.
PROG
Repeat play
You can play any desired track or disc repeatedly.
Press REP to select the repeat mode.
REP
Numeric
buttons
$ !/
^
&
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
REP
RANDOM
PROG
ABC
TEXT
/
TIME
R. TIME
DE
FREQ
/
RDS MODE
PTY SEEK
START
POWER
1 2 3
123
4 5 6
456
7 8 9
78
0 +10 +100
FREQ
/
RDS MODE
PTY SEEK
START
REP
RANDOM
PROG
ABC
TEXT
/
TIME
R. TIME
DE
TAPE
DIRECTION
PRESET
TUNER
PRESET
MD CD TAPE
AUX
MD
REC
/
PAUSE
TAPE
REC
/
PAU SE
MODE
SLEEP
DISPLAY
DUBBING
VOLUME
START
PROG
SREP
FREP
CD OPERATIONS
0107CRXE300(M).15-18.E 02.5.24, 3:35 PM17
18
To stop program play mode
Press &.
Note
/ or $/! can be used during program play to skip
to tracks within the program.
To check program data
1. Press & to stop program play.
2. Press PROG. Then each time you press / /
$/!, the track number and the program number
are displayed in the order of the program.
To change program data
1. Follow the preceding procedure described in To
check program data.
2. Display the track number to be changed by pressing
/ /
$/!.
3. Press the numeric button of the desired track. The
previously programmed track will be cleared from
memory and the new one will be programmed.
To delete all program data
When program play is stopped, press &.
Note
Turning the unit to the standby mode or opening the disc tray
also deletes the program data.
CD OPERATIONS
0107CRXE300(M).15-18.E 02.5.24, 3:35 PM18
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192

Yamaha CRX-E300 Инструкция по применению

Категория
Ресиверы
Тип
Инструкция по применению

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ