ABB PowerValue 11 RT Quick Manual

PowerValue 11 RT

1-3 kVA B

1-3 kVA S

Quick guide

Quick guide | PowerValue 11 RT 1-3 kVA 1

1

2

2 PowerValue 11 RT 1-3 kVA | Quick guide

3

4

Quick guide | PowerValue 11 RT 1-3 kVA 3

5

6

4 PowerValue 11 RT 1-3 kVA | Quick guide

7

Quick guide | PowerValue 11 RT 1-3 kVA 5

8

9

10

11

6 PowerValue 11 RT 1-3 kVA | Quick guide

Quick guide | PowerValue 11 RT 1-3 kVA 7

PowerValue 11 RT 1-3 kVA

1en

es

da

zh

fr

ﬁ

ru

nl

de

pt

cz

el

it

sv

pl

Quick guide 9

Kurzanleitung 21

Guide de référence rapide 33

Guida rapida 45

Guía rápida 57

Guia de consulta rápida 69

Pikaopas 81

Snabbinstruktion 93

Kvikguide 105

Rychlý průvodce 117

Краткое руководство 129

Skrócony podręcznik 141

速成指南 153

Σύντομος οδηγός 165

Beknopte installatiehandleiding 177

8 PowerValue 11 RT 1-3 kVA | Quick guide

Quick guide | PowerValue 11 RT 1-3 kVA 9

1en

PowerValue 11 RT 1-3 kVA

Quick guide

Safety instructions 10

Installation 15

Operation 17

Troubleshooting 19

10 PowerValue 11 RT 1-3 kVA | Quick guide

en

Safety instructions

Read carefully

Always follow the precautions and instructions described in this manual. Any

deviations from the instructions may result in electrical shock or cause accidental

load loss.

ABB DOES NOT TAKE ANY RESPONSIBILITY FOR DAMAGES CAUSED THROUGH INCORRECT

MANIPULATIONS OF THE UPS SYSTEM.

Safety notices

WARNING

WARNING INDICATES THE PRESENCE OF A HAZARD WHICH COULD

RESULT IN SEVERE INJURY AND/OR SERIOUS DAMAGE TO THE SYSTEM.

CAUTION

CAUTION INDICATES THE PRESENCE OF A HAZARD WHICH COULD

RESULT IN MINOR INJURY AND/OR DAMAGE TO THE PRODUCT.

NOTE

NOTE INDICATES THE PRESENCE OF A HAZARD WHICH COULD LEAD TO

PROPERTY DAMAGE.

Safety symbols

SAFETY WARNING: THE SYMBOL IS USED TO ALERT THE USER TO WARNINGS,

CAUTIONS AND NOTES.

DANGER: THE SYMBOL IS USED TO ALERT THE USER TO THE OCCURRENCE

OF ELECTRICAL LIVE PARTS WITH HAZARDOUS VOLTAGES.

Quick guide | PowerValue 11 RT 1-3 kVA 11

1en

Batteries

DANGER

WARNING

COMPONENTS INSIDE THE UPS ARE CONNECTED TO THE

BATTERY EVEN WHEN THE UPS IS DISCONNECTED FROM

THE MAINS POWER SUPPLY.

DANGER

WARNING

DISCONNECT THE BATTERIES BEFORE CARRYING OUT ANY

KIND OF SERVICE AND/OR MAINTENANCE. VERIFY THAT NO

CURRENT IS PRESENT AND NO HAZARDOUS VOLTAGE

EXISTS IN THE CAPACITOR OR BUS CAPACITOR TERMINALS.

DANGER

WARNING

A BATTERY CAN PRESENT A RISK OF ELECTRICAL SHOCK

AND HIGH SHORT CIRCUIT CURRENT. THE FOLLOWING

PRECAUTIONS MUST BE OBSERVED WHEN WORKING ON

BATTERIES:

• REMOVE WATCHES, RINGS OR OTHER METAL OBJECTS

• MAKE USE OF PROPER PPE (PERSONAL PROTECTION

EQUIPMENT) AS PER LOCAL POLICIES AND RULES

— WEAR FLAME/ARC RESISTANT WHOLE BODY

CLOTHING

— WEAR SUITABLE VOLTAGE RATED GLOVES

— USE SAFETY DIELECTRIC FOOTWEAR

— WEAR ARC FLASH FACE SHIELD

— USE VOLTAGE RATED TOOLS

• DO NOT LAY TOOLS OR METAL PARTS ON TOP OF

BATTERIES

• DISCONNECT THE CHARGING SOURCE PRIOR TO

CONNECTING OR DISCONNECTING BATTERY TERMINALS.

DANGER

WARNING

THE BATTERY CIRCUIT IS NOT ISOLATED FROM THE INPUT

VOLTAGE. HAZARDOUS VOLTAGES MAY OCCUR BETWEEN

THE BATTERY TERMINALS AND THE GROUND. VERIFY THAT

NO VOLTAGE IS PRESENT BEFORE SERVICING.

WARNING

NEVER DISPOSE BATTERIES ON FIRE AS THEY MAY EXPLODE.

12 PowerValue 11 RT 1-3 kVA | Quick guide

en

WARNING

DO NOT OPEN OR MUTILATE THE BATTERIES.

WARNING

RELEASED ELECTROLYTE IS HARMFUL TO THE SKIN AND EYES.

CAUTION

REPLACE BATTERIES WITH THE SAME NUMBER AND SAME TYPE OF

BATTERIES.

Installation

DANGER

WARNING

HIGH FAULT CURRENTS (LEAKAGE CURRENTS). BEFORE

CONNECTING THE MAINS ENSURE THAT the UPS IS

ELECTRICALLY GROUNDED!

DANGER

WARNING

DO NOT REMOVE ANY SCREWS FROM THE UPS SYSTEM OR

FROM THE BATTERY CABINET: DANGER OF ELECTRICAL

SHOCK.

DANGER

WARNING

WHEN OPENING OR REMOVING THE UPS-COVERS YOU ARE

EXPOSED TO DANGEROUS VOLTAGES.

Quick guide | PowerValue 11 RT 1-3 kVA 13

1en

WARNING

WATER CONDENSING MAY OCCUR IF THE UPS IS UNPACKED IN A VERY

LOW TEMPERATURE. IN THIS CASE IT IS NECESSARY TO WAIT UNTIL THE

UPS IS FULLY DRIED INSIDE OUT BEFORE PROCEEDING INSTALLATION

AND USE TO AVOID HAZARDS AND ELECTRIC SHOCK, WAIT UNTIL THE

UPS IS FULLY DRY BOTH INSIDE AND OUTSIDE BEFORE INSTALLING.

CAUTION

AN INTEGRAL SINGLE EMERGENCY SWITCHING DEVICE THAT PREVENTS

FURTHER SUPPLY TO THE LOAD BY THE UPS IN ANY MODE OF

OPERATION MUST BE PROVIDED IN THE BUILDING WIRING INSTALLATION.

CAUTION

DO NOT CONNECT EQUIPMENT THAT COULD OVERLOAD THE UPS

SYSTEM (FOR EXAMPLE LASER PRINTERS).

Operation

CAUTION

DO NOT OPERATE IN CASE OF PRESENCE OF WATER OR MOISTURE.

CAUTION

DO NOT DISCONNECT THE MAINS CABLE FROM THE UPS OR THE

BUILDING WIRING SOCKET DURING OPERATION AS THIS REMOVES THE

GROUND FROM THE UPS AND ALL CONNECTED LOADS.

CAUTION

SWITCH OFF THE CONNECTED LOADS BEFORE TURNING ON THE UPS.

THEN SWITCH ON THE LOADS ONE BY ONE AFTER THE UPS IS TURNED

ON. SWITCH OFF ALL OF THE CONNECTED LOADS BEFORE TURNING OFF

THE UPS.

CAUTION

REPLACE FUSES ONLY BY DEVICES OF THE SAME TYPE AND OF THE

SAME AMPERAGE TO AVOID FIRE HAZARDS.

14 PowerValue 11 RT 1-3 kVA | Quick guide

en

CAUTION

INDISCRIMINATE OPERATION OF SWITCHES MAY CAUSE OUTPUT LOSS OR

DAMAGE TO EQUIPMENT.

NOTE

PRESS THE OFF BUTTON TO FULLY DISCONNECT THE UPS. WAIT UNTIL

THE UPS IS ON BYPASS OR ON STAND-BY MODE BEFORE

DISCONNECTING IT FROM THE MAINS.

Quick guide | PowerValue 11 RT 1-3 kVA 15

1en

Installation

Planning before installation

Install the unit to a position where any danger to the UPS is minimized to ensure a

long service life:

• Install the UPS indoors.

• Leave 25 cm of space on each side of the cabinet to enable cooling airflow and

ensure that the circulation of air to the ventilation slits is not obstructed.

• Avoid excessively high temperature and excessive moisture.

• Make sure that the surface is solid and flat.

Rack mount installation – requires rack mounting kit, to be purchased

separately

PowerValue 11 RT can be installed in a 19-inch rack. Both the UPS and the external

battery enclosure are 2U in height.

• Align the rack mounting ears on the side of the UPS and tighten the screws.

(Fig.1)

• Assemble the rack rails with the rack-mounting kit. (Fig.2)

• Slide the UPS into the rack rail and lock it into the structure. (Fig.3)

• Tighten the screws and then proceed with wiring of the UPS .

Tower installation

• Place the UPS in a vertical position with the front panel screws orientated as in

Fig.4

• Place the two stands on a horizontal surface (Fig.4)

• Place the UPS carefully on the UPS stands (Fig.4-5)

• Pull out the LCD box. Rotate it 90º clockwise and then push it back into the front

panel (Fig.6-7)

16 PowerValue 11 RT 1-3 kVA | Quick guide

en

Electrical connections

• PowerValue 11 RT 1 kVA B, 1 kVA S, 2 kVA B (see Fig.8)

• PowerValue 11 RT 2 kVA S (see Fig.9)

• PowerValue 11 RT 3 kVA B (see Fig.10)

• PowerValue 11 RT 3 kVA S (see Fig.11)

Legend

1 AC output

2 EPO / Dry contact input port

3 USB port

4 AC input

5 Dry contact output port

6 SNMP/ AS400 slot

7 RS232

8 HI-POT screw

9 GND contact

Quick guide | PowerValue 11 RT 1-3 kVA 17

1en

Operation

You can operate the UPS through the user-friendly display (see chapter 4 of the user

manual for a full list of possible operations).

Power on/off

Scroll up

Scroll down

Select / Edit

UPS start-up

To start up the UPS with mains supply:

1. Check that all cables are connected correctly and well-fixed mechanically.

2. Connect the UPS to the power supply.

3. Keep the power-on button pressed for longer than 1 second. The alarm buzzer

will sound for 1 second and the UPS will start up.

4. After a few seconds, the UPS goes to online-mode. If the mains power is

abnormal, the UPS will transfer to battery-mode without interruption in the output

of the UPS.

18 PowerValue 11 RT 1-3 kVA | Quick guide

en

To start up the UPS without mains supply (cold start):

1. Check that all cables are connected correctly and well-fixed mechanically.

2. Press the power-on button. The UPS will perform a self-test and display the

status screen.

3. Keep the power-on button pressed for longer than 1 second. The alarm buzzer

sounds and the UPS will start up.

4. After a few seconds, the UPS transfers to battery-mode. When the UPS is

supplied with power from the mains, the UPS transfers to online-mode without

interruption in the output of the UPS.

UPS Shutdown

To shut down the UPS with mains supply:

1. If the UPS is working on bypass-mode, go to step 3.

2. If the UPS is on online-mode, keep the power-on button pressed for more than 3

seconds. The alarm buzzer will sound and the UPS will transfer to bypass-mode.

Note that the output is still energized.

3. Disconnect the mains power supply. The display will shut down and the output

voltage will be removed from the UPS output terminal.

4. In case bypass has been disabled through the Settings menu, keep the power-

on button pressed for more than 3 seconds to shut down the UPS. The unit will

transfer from online to stand-by mode. Disconnect the input power cable and the

display will shut down.

To shut down the UPS without mains supply:

1. To power off the UPS, keep the power on/off button pressed for more than 3

seconds. The alarm buzzer will sound for 3 seconds and the output power will be

immediately cut-off.

2. The display will shut down and the output voltage will be removed from the UPS

output terminal.

Страница загружается...

ABB PowerValue 11 RT Quick Manual

Похожие модели бренда

Модели других брендов