Yamaha A-S2000 Инструкция по применению

BLACK

DIC 2181s*

Printed in Malaysia WM15620-1

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

G

Stereo Amplifier

Amplificateur Stéréo

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАЦИИ

HiFi Began with Yamaha

Yamaha’s involvement with and passion for music goes back

more than a century, to when we built our first reed organ in

1887. Now we are the world’s leading producer of pianos and

other musical instruments, and are involved with music in many

other ways as well. We manufacture professional recording

equipment, we design concert halls and we assist artists at

concerts with set up and sound tuning.

This knowledge and experience benefits our production of

audio components in many ways. We introduced our first HiFi

(High Fidelity) turntable in 1954. Thereafter we were one of the first

to offer mass-produced, high quality audio equipment,

and introduced many legendary stereo components.

We hope you enjoy the genuine HiFi experience of

Yamaha Natural Sound.

Excellence in Audio Achievement

First HiFi System introduced in 1920

We introduced numerous HiFi components

(turntables, FM/AM tuners, integrated

amplifiers, preamplifiers, power amplifiers

and speakers) in 1955 - 1965.

Natural Sound Speaker Series introduced

in 1967

NS-20 Monitor Speaker

CA-1000 Integrated Amplifier

Featuring A-Class operation, the CA-1000 set

the standard for integrated amplifiers.

NS-690 Monitor Speaker

NS-1000M Monitor Speaker

A truly legendary speaker still revered by HiFi

enthusiasts.

B-1 Power Amplifier

An innovative power amp that used FETs in all

stages.

C-2 Control Amplifier

Received top prize at the Milan International Music

and HiFi Show.

NS-10M Studio Monitor Speaker

Became of the most popular studio monitors

in the world.

A-1 Integrated Amplifier

PX-2 Turntable

Yamaha’s first straight arm turntable.

B-6 Power Amplifier

Pyramid-shaped power amplifier.

GT-2000/L Turntable

First CD Player (CD-1) introduced in 1983

B-2x Power Amplifier

MX-10000 Power Amplifier and

CX-10000 Control Amplifier

Redefined the capabilities of separate components.

AX-1 Integrated Amplifier

GT-CD1 CD Player

MX-1 Power Amplifier and

CX-1 Preamplifier

Soavo-1 and Soavo-2 Natural Sound

Speaker Systems

A-S2000 Stereo Amplifier and

CD-S2000 Super Audio CD Player

4 En

◆ Full floating and balanced circuit design achieves for the first time the

full potential of analogue amplification

An entirely new floating and balanced power amp achieves complete symmetry and permits full balanced transmission

(amplification) from the input jack to just before the speaker jack

◆ Full-stage balanced signal transmission

The world’s first integrated amp to offer full stage balanced transmission, combining high power output with good sound

texture and outstanding S/N performance

◆ Floating and balanced power amp

◆ Fully balanced control amp

◆ Fully balanced digital volume and tone controls

◆ Four large capacity power supplies

◆ Symmetrical construction

◆ Headphone amp for low impedance drive

■ Supplied accessories

Please check that you have received all of the following parts.

• Remote control

• Batteries (AA, R06, UM-3) (×2)

• Power cable

• Safety brochure

■ About this manual

• y indicates a tip for your operation.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In

case of differences between the manual and the product, the product has priority.

• The color of images in this manual may vary from the original.

• Read the safety brochure before using this unit.

Contents

Controls and functions.......................................................................................................................................... 6

Connections.......................................................................................................................................................... 14

Specifications ....................................................................................................................................................... 20

Troubleshooting................................................................................................................................................... 24

5 En

Controls and functions

In this chapter, you will learn the controls and functions of A-S2000.

6 En

Controls and functions

■ Front panel (left side)

1 POWER

Press upward or downward to turn on or off this unit.

y

The POWER indicator above lights up when this unit is turned

on.

• If the POWER indicator flashes when you turn on this unit,

disconnect the AC power cable and contact the nearest

authorized Yamaha dealer or service center (see page 24).

• When you turn on this unit, there will be a few second delay

before this unit can reproduce sound.

2 Remote control sensor

Receives signals from the remote control.

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the front panel of this unit during

operation.

SPEAKERSTRIMPHONESPOWER

OFF

ON

dB

A

B

A+B

BI-WIRING

0

-6 +6

+12

OFF

BASS

+

-

41325

Notes

30 30

Approximately 6 m (20 ft)

7 En

3 PHONES jack

Outputs audio for private listening with headphones.

When headphones are plugged in:

– Both speaker sets connected to the SPEAKERS L/R CH A

and B terminals are turned off.

– No signals are output at the PRE OUT jacks, while signals are

output at the REC jacks.

– You cannot select MAIN DIRECT as the input source.

– If headphones are plugged into the PHONES jack while

MAIN DIRECT is selected as the input source, no audio is

output at the PHONES jack.

4 TRIM

Adjusts the volume level when headphones are plugged in

to avoid sudden changes in volume.

Choices: –6 dB, 0 dB, +6 dB, +12 dB

5 SPEAKERS

Turns on or off the speaker set connected to the

SPEAKERS L/R CH A and/or B terminals on the rear

panel.

• Switch to the OFF position to turn off both speaker

sets.

• Switch to the A or B position to turn on the speaker set

connected to the SPEAKERS L/R CH A or B

terminals.

• Switch to the A+B BI-WIRING position to turn on

both speaker sets.

If you use two sets (A and B), the impedance of each speaker

must be 8 Ω or higher.

BALANCE

VOLUMEINPUT

TREBLE

MC

MM

MAIN DIRECT

LINE 2

LINE 1

CD BAL

CD

TUNER

PHONO

AUDIO MUTEPHONO

RL+

-

Note

Caution

English

8 En

Controls and functions

■ Front panel (right side)

6 BASS

Increases or decreases the low frequency response. The 0

position produces a flat response.

Control range: –10 dB to +10 dB

7 TREBLE

Increases or decreases the high frequency response. The 0

position produces a flat response.

Control range: –10 dB to +10 dB

• When both the BASS and TREBLE controls are set to the 0

position, audio signal bypasses the tone control circuitry.

• The BASS and TREBLE controls do not affect the signals input

at the MAIN DIRECT jacks and signals output at the REC OUT

jacks.

8 BALANCE

Adjusts the audio output balance of the left and right

speakers to compensate for sound imbalances caused by

speaker locations or listening room conditions.

The BALANCE control does not affect the signals input at the

MAIN DIRECT jacks and signals output at the REC OUT jacks.

9 PHONO

Selects the type of magnetic cartridge of the turntable

connected to the PHONO jacks on the rear panel.

• Press upward to the MM position when the connected

turntable has a moving magnet (MM) cartridge.

• Press downward to the MC position when the

connected turntable has a moving coil (MC) cartridge.

• When you replace the cartridge, be sure to turn off this

unit.

SPEAKERSTRIMPHONESPOWER

OFF

ON

dB

A

B

A+B

BI-WIRING

0

-6 +6

+12

OFF

BASS

+

-

6

Notes

Note

9 En

0 INPUT selector

Selects the input source you want to listen to.

The audio signals of the selected input source are also

output at the REC jacks.

• Switch to the CD BAL position to select the CD player

connected to the CD BAL jacks (balanced XLR jacks).

• Switch to the CD position to select the CD player connected to

the CD jacks (unbalanced RCA jacks).

• Switch to the MAIN DIRECT position to select the component

connected to the MAIN IN jacks. When MAIN DIRECT is

selected as the input source, no signals are output at the PRE

OUT, REC, and PHONES jacks.

A AUDIO MUTE

Press downward to reduce the current volume level by

approximately 20 dB. Press again to restore the audio

output to the previous volume level.

y

• The AUDIO MUTE indicator lights up while the mute function

is on.

• You can also rotate VOLUME on the front panel or press

VOL +/– on the remote control to resume the audio output.

B VOLUME

Controls the volume level. This does not affect the REC

level.

The VOLUME control does not affect when you select MAIN

DIRECT as the input source. Adjust the volume level using the

volume control on the external amplifier connected to the MAIN

DIRECT jacks.

BALANCE

VOLUMEINPUT

TREBLE

MC

MM

MAIN DIRECT

LINE 2

LINE 1

CD BAL

CD

TUNER

PHONO

AUDIO MUTEPHONO

RL+

-

BA9087

Notes

Note

English

10 En

Controls and functions

■ Rear panel

1 SPEAKERS L/R CH terminals

2 INPUT jacks

3 LINE2 jacks

4 MAIN IN jacks

Adjust the volume level using the volume control on the external

amplifier connected to the MAIN DIRECT jacks when you select

MAIN DIRECT as the input source.

5 PRE OUT jacks

• When you connect audio pin plugs to the PRE OUT jacks to

drive the speakers using an external amplifier, it is not

necessary to use the SPEAKERS L/R CH terminals.

• The signal output at the PRE OUT jacks are affected by the tone

control settings.

• The PRE OUT jacks output the same channel signal as the

SPEAKERS L/R CH terminals.

• When you use a subwoofer, connect it to the PRE OUT jacks

and speakers to the SPEAKERS L/R CH terminals.

LINE2

RECPBLINE 1TUNER

GND

L

R

LR

PHONO

CD

BAL

INPUTSPEAKERS R CH

A

B

L

R

1 23

See page 14 for connection information.

Note

Notes

11 En

6 AC IN

Use this inlet to plug in the supplied power cable.

7 VOLTAGE SELECTOR

(Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

the AC power cable into the AC wall outlet. Improper

setting of the VOLTAGE SELECTOR may cause damage

to this unit and create a potential fire hazard.

Rotate the VOLTAGE SELECTOR clockwise or

counterclockwise to the correct position using a straight

slot screwdriver.

Voltages are as follows:

AC 110/120/220/230–240 V, 50/60 Hz

8 Foot

The feet of this unit include built-in spikes. Using the

spikes can reduce the effect of vibrations on the set. When

using the spikes, remove the magnet foot by pulling it.

When using the feet’s built-in spikes, the spikes may scratch the

shelf or floor on which this unit is installed. Use the supports

when placing this unit on expensive furniture, etc.

y

If this unit is unstable, you can adjust the foot height by rotating

it.

AC IN

SPEAKERS L CH

PRE OUTMAIN IN

L

R

A

B

VOLTAGE SELECTOR

5 1 7

8

64

230-

240V

Caution

Spike

English

12 En

Controls and functions

■ Remote control

1 Infrared signal transmitter

Outputs infrared control signals.

2 Yamaha tuner control buttons

Control functions of Yamaha tuner. Refer to the owner’s

manual of your tuner for details.

Some components may not be controlled by this remote control.

3 Yamaha CD player control buttons

Control various functions of Yamaha CD player. Refer to

the owner’s manual of your CD player for details.

y

Press once to pause and twice to stop playback.

Some components may not be controlled by this remote control.

4 Amplifier control buttons

INPUT /

Selects the input source you want to listen to.

• When MAIN DIRECT is selected as the input source, no

signals are output at the PRE OUT and REC jacks.

• If headphones are plugged into the PHONES jack while MAIN

DIRECT is selected as the input source, no audio is output at

the PHONES jack.

VOL +/–

Controls the volume level.

The VOLUME control does not affect when you select MAIN

DIRECT as the input source. Adjust the volume level using the

volume control on the external amplifier connected to the MAIN

DIRECT jacks.

MUTE

Reduces the current volume level by approximately 20

dB. Press again to restore the audio output to the previous

volume level.

y

You can also press VOL +/– to resume the audio output.

■ Installing batteries in the remote control

1 Press the part and slide the battery

compartment cover off.

2 Insert the two supplied batteries

(AA, R06, UM-3) according to the polarity

markings (+ and –) on the inside of the

battery compartment.

3 Slide the cover back until it snaps into place.

Note

A/B/C/D/E

PRESET

INPUTINPUT

VOL

MUTE

VOL

1

2

3

4

Notes

Note

2

1

3

Connections

In this section, you will make connections between A-S2000, speakers,

and source components.

14 En

Connections

• Do not let the bare speaker wires touch each other or do not let

them touch any metal part of this unit. This could damage this

unit and/or the speakers.

• All connections must be correct: L (left) to L, R (right) to R,

“+” to “+”, and “–” to “–”. If the connections are faulty, no

sound will be heard from the speakers, and if the polarity of the

speaker connections is incorrect, the sound will be unnatural

and lack bass. Also, refer to the owner’s manual for each of

your components.

• Use RCA unbalanced cables to connect other components

except speakers. Use “male” XLR balanced cables to connect a

CD player with XLR balanced output jacks to the CD BAL

jacks of this unit.

• Connect your turntable to the GND terminal to reduce noise in

the signal. However, you may hear less noise without the

connection to the GND terminal for some record players.

Caution

LINE2

PRE OUTMAIN IN

RECPBLINE 1TUNER

GND

L

R

LR

PHONO

CD

BAL

INPUTSPEAKERS R CH

A

B

L

R

+

-

+

-

CD player with

RCA jacks

Ground

Speakers A

(R channel)

Speakers B

(R channel)

CD player with

XLR jacks

Tuner

Turntable

DVD player,

etc.

15 En

• Because the power amplifier of A-S2000 is of the floating

balanced type, the following types of connections are not

possible.

– Connecting with the left channel “–” terminal and the right

channel “–” terminal as well as “+” terminals (Fig. 1).

– Deliberately connecting with the left/right channel “–”

terminals and metal part on the rear panel of this unit, as well

as accidentally touching them.

– Connecting with the left channel “–” terminal and the right

channel “–” terminal inverted (cross connection, Fig. 2).

• Do not connect your active subwoofer to the SPEAKERS

terminal. Connect it to the PRE OUT jacks of this unit.

Caution

AC IN

SPEAKERS L CH

LINE2

PRE OUTMAIN IN

RECPBLINE 1TUNER

GND

L

INPUT

L

R

A

B

+–

+

-

CD recorder,

tape deck, etc.

Speakers A

(L channel)

Speakers B

(L channel)

External amplifier or

active subwoofer

Preamplifier,

AV receiver, etc.

+

–

+

–

L

R

+

–

+

–

L

R

+

–

+

–

L

R

+

–

+

–

L

R

Fig. 1 Fig. 2

English

16 En

Connections

■ Connecting the speakers

1 Remove approximately 10 mm (0.4 in) of

insulation from the end of each speaker

cable and twist the exposed wires of the

cable together to prevent short circuits.

2 Unscrew the knob and then insert the bare

wire into the hole.

3 Tighten the knob.

■ Connecting the banana plug

(Except for Europe models)

First, tighten the knob and then insert the banana

plug into the end of the corresponding terminal.

■ Connecting the Y-shaped lug

1 Unscrew the knob and then sandwich the Y-

shaped lug between the ring part and base.

2 Tighten the knob.

10 mm (0.4 in)

Banana plug

Y-shaped lug

Slide

17 En

■ Bi-wire connection

The bi-wire connection separates the woofer from the

combined midrange and tweeter section. A bi-wire

compatible speaker has four binding post terminals. These

two sets of terminals allow the speaker to be split into two

independent sections. This split connects the mid and high

frequency drivers to one set of terminals and the low

frequency driver to the other pair.

To use the bi-wire connections, the impedance of each speaker

must be 8 Ω or higher.

• Remove the shorting bars or bridges to separate the LPF (low

pass filter) and HPF (high pass filter) crossovers.

• To use the bi-wire connections, switch the SPEAKERS selector

to the A+B BI-WIRING position.

■ Connecting to the CD BAL jacks

Connect your CD player with the XLR balanced output

jacks. The pin assignments for these jacks are shown

below. Refer to the owner’s manual supplied with your

CD player and verify that its XLR balanced output jacks

are compatible with the pin assignments.

When connecting, be sure to match the pins and insert the

connector of the “male” XLR balanced cable until you

hear a “click”. When disconnecting, pull out the “male”

XLR balanced cable while holding down the lever of the

CD BAL jacks.

To use the XLR balanced connection, you must switch the

INPUT selector on the front panel to the CD BAL position.

Caution

Notes

Note

1: ground2: hot

3: cold

“Female” XLR connector

“Male” XLR connector

English

18 En

Connections

■ VOLTAGE SELECTOR

(Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local voltage BEFORE plugging the

power cable into the AC wall outlet. Improper setting of

the VOLTAGE SELECTOR may cause damage to this

unit and create a potential fire hazard.

Rotate the VOLTAGE SELECTOR clockwise or

counterclockwise to the correct position using a straight

slot screwdriver.

Voltages are as follows:

........................AC 110/120/220/230–240 V, 50/60 Hz

■ Connecting the power cable

Plug the power cable into the AC IN connector when all

connections are complete, and then plug in the power

cable to the AC outlet.

Caution

230-

240V

VOLTAGE SELECTOR

Voltage

indication

Specifications

In this section, you will find technical specifications for A-S2000.

20 En

Specifications

POWER SECTION

• Minimum RMS Output Power

(8 Ω , 20 Hz to 20 kHz, 0.02% THD) ...................... 90 W + 90 W

(4 Ω , 20 Hz to 20 kHz, 0.02% THD) .................. 150 W + 150 W

• Dynamic Power (IHF) (8/6/4/2 Ω) ................... 105/135/190/220 W

• Maximum Output Power

(1 kHz, 0.7% THD, 4 Ω) [U.K. and Europe models only]

.......................................................................................... 160 W

• Maximum Useful Output Power (JEITA)

(1 kHz, 10% THD, 8/4 Ω)

[Asia, General, China and Korea models only] ....... 120/190 W

• Dynamic Headroom

8 Ω ..................................................................................... 0.67 dB

• IEC Output Power [U.K. and Europe models only]

(1 kHz, 0.02% THD, 8/4 Ω)............................................ 95/155 W

• Damping Factor

1 kHz, 8 Ω ................................................................................ 160

• Maximum Input Signal

CD BAL, CD, etc.................................................................. 2.8 V

PHONO MM (1 kHz) ........................................................ 120 mV

PHONO MC (1 kHz) ............................................................ 7 mV

• Frequency Response

CD, etc. (Flat Position, 5 Hz to 100 kHz) ...................... +0/−3 dB

CD, etc. (Flat Position, 20 Hz to 20 kHz) ................... +0/−0.3 dB

• RIAA Equalization Deviation

PHONO MM (20 Hz to 20 kHz) ...................................... ±0.5 dB

PHONO MC (20 Hz to 20 kHz) ....................................... ±0.5 dB

• Total Harmonic Distortion

CD BAL to SP OUT

(20 Hz to 20 kHz, 90 W/8 Ω) ............................................. 0.01%

CD, etc. to SP OUT

(20 Hz to 20 kHz, 90 W/8 Ω) ........................................... 0.015%

PHONO MM to REC

(20 Hz to 20 kHz, 2 V) ..................................................... 0.005%

PHONO MC to REC

(20 Hz to 20 kHz, 2 V) ....................................................... 0.05%

• Intermodulation Distortion

CD, etc. to SP OUT

(Rated output/8 Ω) .............................................................0.02%

• Signal to Noise Ratio (IHF-A Network)

CD, etc. (150 mV, Input shorted) ..........................................98 dB

PHONO MM (5 mV, Input shorted) .....................................93 dB

PHONO MC (500 µV, Input shorted) ..................................85 dB

• Residual Noise (IHF-A Network) (CD, etc.) .......................... 33 µV

CONTROL SECTION

• Input Sensitivity/Input Impedance

CD, etc. .................................................................. 150 mV/47 kΩ

MM ......................................................................... 2.5 mV/47 kΩ

MC ........................................................................... 100 µV/50 Ω

MAIN IN ...................................................................... 1 V/47 kΩ

• Output Level/Output Impedance

REC OUT ............................................................. 150 mV/1.5 kΩ

PRE OUT ..................................................................... 1 V/1.5 kΩ

• Headphone Rated Output

1 kHz, 32 Ω , 0.2% THD ................................................... 30 mW

• Channel Separation

CD, etc. (5.1 kΩ Terminated, 1/10 kHz) ........................ 74/54 dB

PHONO MM (Input shorted, 1 kHz/10 kHz, Vol.:−30 dB)

.......................................................................................90/77 dB

PHONO MC (Input shorted, 1 kHz/10 kHz, Vol.:−30 dB)

.......................................................................................66/77 dB

• Tone Control Characteristics

BASS

Boost/Cut (50 Hz) ............................................................. ±9 dB

Turnover Frequency ........................................................ 350 Hz

TREBLE

Boost/Cut (20 kHz) ........................................................... ±9 dB

Turnover Frequency ....................................................... 3.5 kHz

• Audio muting......................................................... –20 dB (approx.)

GENERAL

• Power Supply

[U.S.A. and Canada models] ............................. AC 120 V, 60 Hz

[Asia model] .................................. AC 220/230–240 V, 50/60 Hz

[General model] ............... AC 110/120/220/230–240 V, 50/60 Hz

[China model] .................................................... AC 220 V, 50 Hz

[Korea model] .................................................... AC 220 V, 60 Hz

[Australia model] ............................................... AC 240 V, 50 Hz

[U.K. and Europe models] ................................. AC 230 V, 50 Hz

• Power consumption ................................................................ 350 W

• Idling power consumption.........................................................80 W

• Off-state power consumption ......................................................0 W

• Dimensions (W x H x D) ................................. 435 x 137 x 465 mm

(17-1/8” x 5-3/8” x 18-5/16”)

• Weight .................................................................... 22.7 kg (50 lbs.)

* Specifications are subject to change without notice.

01EN_03_Add_A-S2000_G.fm Page 20 Wednesday, August 6, 2008 1:06 PM

Black process 45.0° 240.0 LPI

Страница загружается...

Yamaha A-S2000 Инструкция по применению

Похожие модели бренда

Модели других брендов