Tripp Lite Audio/Video Инструкция по применению

1

Owner’s Manual

Audio/Video with RS-232

and IR Control over IP Extenders

Extender Kit Models:

B160-101-DPSI, B160-101-HDSI, B160-201-HSI

Transmitter Models:

B160-001-CSI, B160-001-DPSI,

B160-001-HDSI, B160-001-VSI

Receiver Models:

B160-100-CSI, B160-100-DPSI, B160-100-HDSI,

B160-100-VSI, B160-200-HSI

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

All trademarks are the sole property of their respective owners.

Español 21 • Français 41 • Русский 61

17-02-099-9336B2.indb 1 3/2/2017 1:33:56 PM

2

Package Contents

B160-001-CSI

B160-001-DPSI

B160-001-HDSI

B160-001-VSI

B160-100-CSI

B160-100-DPSI

B160-100-HDSI

B160-100-VSI

B160-200-HSI

B160-101-DPSI

B160-101-HDSI

B160-201-HSI

Transmitter (T), Receiver (R), Kit (K) T T T T R R R R R K K K

External Power Supply 1 1 1 1 1 1 1 1 1 2 2 2

IR-In Cable 0 0 0 0 1 1 1 1 1 1 1 1

IR-Out Cable 1 1 1 1 0 0 0 0 0 1 1 1

3.5 mm to DB9 M/F Adapter Cable 1 1 0 1 0 0 0 0 0 1 0 0

3.5 mm to DB9 M/M Adapter Cable 0 0 0 0 1 1 0 1 1 1 0 1

HDMI to DVI Adapter Cable 0 0 1 0 0 0 1 0 0 0 2 0

Mounting Hardware Y Y Y Y Y Y Y Y Y Y Y Y

Owner’s Manual Y Y Y Y Y Y Y Y Y Y Y Y

17-02-099-9336B2.indb 2 3/2/2017 1:33:56 PM

3

Optional Accessories

• A008-006 Component Video Gold Cable – 6 ft.

• N202-Series Cat6, 24 AWG, Solid-Wire Patch Cables

• NSS-G16D2 16-Port Gigabit L2 Managed Switch with 8-Outlet PDU

• NSS-G24D2 24-Port Gigabit L2 Managed Switch with 12-Outlet PDU

• P502-Series VGA Cables with RGB Coax

• P520-006 RS-232 Serial Extension Cable – 6 ft.

• P561-Series DVI-D Single-Link Cables

• P566-Series HDMI to DVI Adapter Cables

• P568-Series High Speed HDMI Cables

• P569-XXX-LOCK* High Speed HDMI Cables with Ethernet and Locking

Connectors

• P580-Series DisplayPort™ Cables

• P583-Series Mini DisplayPort to DisplayPort Cables

*XXX refers to the length, with cables available in 6 ft. (006), 10 ft. (010) and

15 ft. (015) lengths.

Product Features

• Extend and distribute audio/video, serial and IR control signals over

Cat5/Cat6 cabling.

• Models available with Component Video + Stereo Audio, DisplayPort,

HDMI*, and VGA + Stereo Audio.

• Converts source video to an IP-based signal that can be transmitted to

and distributed through a network switch.

• Transmitters can be located up to 328 ft. (100 m) from the switch,

with an additional 328 ft. (100 m) between the switch and the receiver,

for a total distance of 656 ft. (200 m).

*Connect a DVI source and/or monitor using an HDMI to DVI adapter (select models

include an HDMI to DVI adapter). HDMI to DVI adapter cables (Tripp Lite P566-Series)

are available, sold separately.

17-02-099-9336B2.indb 3 3/2/2017 1:33:56 PM

4

Product Features

• Can also be used in a point-to-point installation where the transmitter

directly connects to a receiver up to 328 ft. (100 m) away.

• Designed for managed network switches with IGMP, which allow login and

remote management via the switch interface.

• Video source can be sent to any analog or digital display (e.g. Component

Video to HDMI, VGA to HDMI, HDMI to DisplayPort, HDMI to HDMI).

• Display a single source on a single monitor or distribute a single signal to

multiple monitors.

• B160-200-HSI and B160-201-HSI receiver units include two HDMI

output ports for connection of two monitors.

• Connect up to 64 transmitters and 255 receivers in a single managed

switch installation.

• Utilizes H.264 video compression standard.

• Extends IR control signals that control a source

(such as a Blu-ray™player) from a remote display.

• Uses a 20 kHz to 60 kHz IR frequency.

• Supports RS-232 Serial baud rates up to 57600 bps.

• VGA video models support video resolutions up to 1920 x 1440,

including 1080p.

• DisplayPort and HDMI models support video resolutions up to

1920 x 1080 (1080p).

• Component video models support video resolutions up to 1080i.

•

Each transmitter features an HDMI output port for connecting a local monitor.

• HDCP and 3D compatible.

• Includes mounting hardware for wall-mount, rack mount or pole mount

installations.

• Plug and play; no software or drivers required.

17-02-099-9336B2.indb 4 3/2/2017 1:33:56 PM

5

Mounting Instructions

Audio/Video over IP extenders include mounting hardware that allows for

a variety of mounting options. The following images demonstrate these

mounting methods.

Note: Model B126-1A1 is shown for illustrative purposes; installation for Audio/Video

over IP extender units is the same.

Wall-mount

19” Rack-mount Pole-mount

17-02-099-9336B2.indb 5 3/2/2017 1:33:59 PM

6

Point-to-Point Installation

Notes:

• Test to ensure the entire installation works properly before pulling cables through

ceilings/walls.

• To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6

cable. Using stranded wire cable or cable with a gauge (AWG) size higher than

recommended will result in a shorter extension distance. Higher gauge cabling

(such as 26 AWG) has a limited transmission capability compared to lower-gauge

cabling. All Tripp Lite N202-Series Cat6 cables use 24 AWG solid wire cabling.

Extended lengths of 23 AWG solid wire Cat6a cable are available from Tripp Lite

as a custom order.

• Transmitter and receiver kits are available in DisplayPort, HDMI and VGA, but

separate transmitters and receivers can be purchased in any combination (e.g.

Component Video to HDMI, VGA to HDMI, HDMI to VGA, HDMI to DisplayPort).

1. Ensure all equipment to be connected is powered off.

2. Connect the audio/video source to the transmitter unit’s input port

(see Optional Accessories for available Tripp Lite audio/video cables).

3. (Optional) Connect the computer’s DB9 port to the transmitter unit’s

serial port. Depending on the model, the serial port will be either DB9 or

3.5 mm. Models with 3.5 mm jacks include a 3.5 mm to DB9 adapter.

Models with DB9 ports require standard RS-232 DB9 cable (sold

separately) for connecting to a computer.

4. (Optional) Connect the included IR-OUT cable to the transmitter unit’s

IR-OUT port. Place the sensor on the IR-OUT cable in an unobstructed

area within clear view of the device being controlled.

Note: The IR-OUT cable receives the signal from the remote control and sends it

to the device being controlled (e.g. Blu-ray player, etc.).

5. (Optional) Using an HDMI cable, connect a local monitor to the

transmitter unit’s HDMI output port (see Optional Accessories for

available Tripp Lite HDMI cables).

6. Connect the external power supply to the local transmitter unit and plug

it into a Tripp Lite Surge Protector, Uninterruptible Power Supply (UPS) or

Power Distribution Unit (PDU).

17-02-099-9336B2.indb 6 3/2/2017 1:33:59 PM

7

Point-to-Point Installation

7. Press the Up / Down buttons to set the Channel Number (0-63) on the

front of the transmitter unit to a number that will also be used on the

receiver unit.

Note: A locking mechanism prevents the Channel Number from being

unintentionally changed. When the Channel Number is locked, hold down the Up

and Down buttons until the Channel Number starts blinking. Then navigate to the

desired Channel using the Up / Down buttons. Once the desired Channel Number

has been selected, lock the Channel Number by holding down the Up and Down

buttons until the Channel Number stops blinking.

8. Using Cat5e/6 cable, connect the transmitter unit’s RJ45 Output port to

the receiver unit’s RJ45 Input port.

Note: The maximum allowable cable length from transmitter to receiver is 328 ft.

(100 m).

9. Connect a monitor to the receiver unit’s audio/video Output port

(See Optional Accessories for available Tripp Lite audio/video cables).

10. (Optional) Connect the serial device’s DB9 port to the receiver unit’s

serial port. Depending on the model, the serial port will be either DB9 or

3.5 mm. Models with 3.5 mm jacks include a 3.5 mm to DB9 adapter.

Models with DB9 ports require standard RS-232 DB9 cable (sold

separately) for connecting a device.

11. (Optional) Connect the included IR-IN cable to the receiver unit’s IR-IN

port. Place the sensor on the IR-IN cable in an unobstructed area within

clear view of the device being controlled.

Note: The IR-IN cable accepts a signal from a remote control and sends it to a

device being controlled on the other end of the installation.

12. Connect the external power supply to the receiver unit and plug it into a

Tripp Lite Surge Protector, Uninterruptible Power Supply (UPS) or Power

Distribution Unit (PDU).

17-02-099-9336B2.indb 7 3/2/2017 1:33:59 PM

8

Point-to-Point Installation

Point-to-Multipoint Installation –

Managed Switch with IGMP

13. Press the Up / Down buttons to set the Channel Number (0-63) on the

front of the receiver unit to a number also used on the transmitter unit.

Note: A locking mechanism prevents the Channel Number from being

unintentionally changed. When the Channel Number is locked, hold down the Up

and Down buttons until the Channel Number starts blinking. Then navigate to the

desired Channel using the Up / Down buttons. Once the desired Channel Number

has been selected, lock the Channel Number by holding down the Up and Down

buttons until the Channel Number stops blinking.

14. Power on all connected devices.

Notes:

• Test to ensure the entire installation works properly before pulling cables through

ceilings/walls.

• To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6

cable. Using stranded wire cable or cable with a gauge (AWG) size higher than

recommended will result in a shorter extension distance. Higher gauge cabling

(such as 26 AWG) has a limited transmission capability compared to lower-gauge

cabling. All Tripp Lite N202-Series Cat6 cables use 24 AWG solid wire cabling.

Extended lengths of 23 AWG solid wire Cat6a cable are available from Tripp Lite

as a custom order.

• B160-Series Audio/Video over IP Extenders are designed for use with a dedicated

network switch. Connecting IP Extenders to a switch used with other networking

equipment will result in degraded or non-functional product performance.

• The installation diagram on the next page shows HDMI transmitters and receivers

only, though any combination of transmitters and receivers (e.g. Component

Video, DisplayPort, HDMI, VGA) may be used. Up to 64 transmitters and 255

receivers can be connected in a single managed switch installation (the diagram

shown stops at a single 16-port network switch).

• The installation diagram on the next page shows only required connections.

Optional connections (such as the IR-IN and IR-OUT Cables) are not shown.

17-02-099-9336B2.indb 8 3/2/2017 1:33:59 PM

9

Point-to-Multipoint Installation –

Managed Switch with IGMP

DC 5V, 2AINPUTOUTPUTRS232OUTPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AINPUTOUTPUTRS232OUTPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AINPUTOUTPUTRS232OUTPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AINPUTOUTPUTRS232OUTPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AINPUTOUTPUTRS232OUTPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AINPUTOUTPUTRS232OUTPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AINPUTOUTPUTRS232OUTPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AINPUTOUTPUTRS232OUTPUT

POWER IR OUT

CHANNEL

UP DOWN

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

Blu-ray

Up to

328 ft.

(100 m)

Blu-ray

Laptop

CPU CPU

Media

Center

Media

Center

Blu-ray

NSS-G16D2

Tx Tx Tx Tx Tx Tx Tx Tx

Rx Rx Rx Rx Rx Rx Rx Rx

1. Ensure all equipment to be connected is powered off.

2. Connect the audio/video source to the transmitter unit’s input port

(see Optional Accessories for available Tripp Lite audio/video cables).

17-02-099-9336B2.indb 9 3/2/2017 1:34:01 PM

10

3. (Optional) Connect the computer’s DB9 port to the transmitter unit’s

serial port. Depending on the model, the serial port will be either DB9 or

3.5 mm. Models with 3.5 mm jacks include a 3.5 mm to DB9 adapter.

Models with DB9 ports require standard RS-232 DB9 cable (sold

separately) for connecting to a computer.

4. (Optional) Connect the included IR-OUT cable to the transmitter unit’s

IR-OUT port. Place the sensor on the IR-IN cable in an unobstructed

area within clear view of the device being controlled.

Note: The IR-OUT cable receives the signal from the remote control and sends it

to the device being controlled (e.g. Blu-ray player, etc.).

5. (Optional) Using an HDMI cable, connect a local monitor to the

transmitter unit’s HDMI output port (see Optional Accessories for

available Tripp Lite HDMI cables).

6. Set the Channel Number (0 to 63 are available) on the front of the

transmitter to a desired number by pressing the Up / Down buttons. This

number MUST be the same on all transmitter and receiver units in the

installation. If you are using transmitter and receiver units that are all

brand new, they will default to Channel Number 0 and you can leave the

channel unchanged upon installation.

Note: A locking mechanism prevents the Channel Number from being

unintentionally changed. When the Channel Number is locked, hold down the Up

and Down buttons until the Channel Number starts blinking. Then navigate to the

desired Channel using the Up / Down buttons. Once the desired Channel Number

has been selected, lock the Channel Number by holding down the Up and Down

buttons until the Channel Number stops blinking.

7. Connect the RJ45 Output port on the transmitter unit to an RJ45 port

on the network switch using Cat5e/6 cable.

Note: The maximum allowable cable length from transmitter to switch is 328 ft.

(100 m).

Do not connect the external power supply to the transmitter at

this time. The transmitter should not be powered on until all

audio/video equipment is connected and powered on.

Point-to-Multipoint Installation –

Managed Switch with IGMP

17-02-099-9336B2.indb 10 3/2/2017 1:34:01 PM

11

8. To connect additional transmitter(s), repeat steps 2 through 7.

9. Connect a monitor to the receiver unit’s audio/video Output port

(See Optional Accessories for available Tripp Lite audio/video cables).

10. (Optional) Connect the serial device’s DB9 port to the receiver unit’s

serial port. Depending on the model, the serial port will be either DB9 or

3.5 mm. Models with 3.5 mm jacks include a 3.5 mm to DB9 adapter.

Models with DB9 ports require standard RS-232 DB9 cable (sold

separately) for connecting a device.

11. (Optional) Connect the included IR-IN cable to the receiver unit’s IR-IN

port. Place the sensor on the IR-IN cable in an unobstructed area within

clear view of the remote control.

Note: The IR-IN cable accepts a signal from a remote control and sends it to a

device being controlled on the other end of the installation.

12. Set the Channel Number (0 to 63 are available) on the front of the

receiver to a desired number by pressing the Up / Down buttons. This

number MUST be the same on all transmitter and receiver units in the

installation. If you are using transmitter and receiver units that are all

brand new, they will default to channel number 0, and you can leave the

channel unchanged upon installation.

Note: A locking mechanism prevents the Channel Number from being

unintentionally changed. When the Channel Number is locked, hold down the Up

and Down buttons until the Channel Number starts blinking. Then navigate to the

desired Channel using the Up / Down buttons. Once the desired Channel Number

has been selected, lock the Channel Number by holding down the Up and Down

buttons until the Channel Number stops blinking.

13. Connect the RJ45 Input port on the receiver unit to an RJ45 port on the

network switch using Cat5e/6 cable.

Note: The maximum allowable cable length from receiver to switch is 328 ft. (100 m).

Do not connect the external power supply to the receiver at

this time. The receiver should not be powered on until all

audio/video equipment is connected and powered on.

Point-to-Multipoint Installation –

Managed Switch with IGMP

17-02-099-9336B2.indb 11 3/2/2017 1:34:01 PM

12

14. To connect additional receivers, repeat steps 9 through 13.

15. Power on all connected devices.

16. Connect the external power supplies to all transmitter and receiver

units in the installation, then plug the external power supplies into

Tripp Lite Surge Protectors, Uninterruptible Power Supplies (UPS) or

Power Distribution Units (PDU).

Point-to-Multipoint Installation –

Managed Switch with IGMP

Operation of Point-to-Multipoint

Installation – Managed Switch with IGMP

Notes:

• B160-Series Audio/Video over IP Extenders are designed for use with a dedicated

network switch. Connecting IP Extenders to a switch used with other networking

equipment will result in degraded or non-functional product performance.

• The model screenshots shown in the steps below are a Tripp Lite NSS-G16D2

Network Switch. Operation of different switches will vary by model.

1. Log into the network switch user interface.

2. Navigate to the VLAN Management section.

17-02-099-9336B2.indb 12 3/2/2017 1:34:01 PM

13

3. In the VLAN Management section, create a new VLAN for each

transmitter in the installation. The transmitter port number should

always be the ﬁrst number in the VLAN, followed by the port numbers

(separated by commas) of all receiver units that will be transmitting

audio/video to and from the selected transmitter. The screenshot below

shows VLAN’s for four transmitters (VLAN0002 through VLAN0005).

VLAN0002 represents the transmitter connected to port 1, the audio/

video of which is transmitted to the receivers connected to ports 7 and

8. Similarly, VLAN0003 represents the transmitter connected to port 2,

whose audio/video is transmitted to receivers connected to ports 9 and

10.

4. To switch the source of the audio/video on a receiver, go to and edit the

VLAN of the associated transmitters to add/remove the desired ports.

5. As more transmitters and receivers get added to the installation,

simply add additional VLANs for the new transmitters and add the new

receivers to the VLANs of the desired transmitters.

Operation of Point-to-Multipoint

Installation – Managed Switch with IGMP

17-02-099-9336B2.indb 13 3/2/2017 1:34:02 PM

14

Notes:

• Unmanaged switch installations are limited to two transmitter units. The number

of receiver units is limited to the number of ports remaining on the unmanaged

switch.

• Test to ensure the entire installation works properly before pulling cables through

ceilings/walls.

• To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6

cable. Using stranded wire cable or cable with a gauge (AWG) size higher than

recommended will result in a shorter extension distance. Higher gauge cabling

(such as 26 AWG) has a limited transmission capability compared to lower-gauge

cabling. All Tripp Lite N202-Series Cat6 cables use 24 AWG solid wire cabling.

Extended lengths of 23 AWG solid wire Cat6a cable are available from Tripp Lite

as a custom order.

• B160-Series Audio/Video over IP Extenders are designed for use with a dedicated

network switch. Connecting IP Extenders to a switch used with other networking

equipment will result in degraded or non-functional product performance.

• The installation diagram on the next page shows HDMI transmitters and receivers

only, though any combination of transmitters and receivers (e.g. Component

Video, DisplayPort, HDMI, VGA) may be used.

• The installation diagram on the next page shows only required connections.

Optional connections (such as the IR-IN and IR-OUT Cables) are not shown.

Point-to-Multipoint Installation –

Unmanaged Switch

17-02-099-9336B2.indb 14 3/2/2017 1:34:02 PM

15

DC 5V, 2AINPUTOUTPUTRS232OUTPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AINPUTOUTPUTRS232OUTPUT

POWER IR OUT

CHANNEL

UP DOWN

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

POWER IR OUT

CHANNEL

UP DOWN

DC 5V, 2AOUTPUTRS232INPUT

Blu-ray

Up to

328 ft.

(100 m)

CPU

Monitors

NSU-G16

Tx Tx Rx Rx Rx Rx Rx Rx

Rx Rx Rx Rx Rx Rx Rx Rx

1. Ensure all equipment to be connected is powered off.

2. Connect the audio/video source to the transmitter unit’s input port

(see Optional Accessories for available Tripp Lite audio/video cables).

3. (Optional) Connect the computer’s DB9 port to the transmitter unit’s

serial port. Depending on the model, the serial port will be either DB9 or

3.5 mm. Models with 3.5 mm jacks include a 3.5 mm to DB9 adapter.

Models with DB9 ports require standard RS-232 DB9 cable (sold

separately) for connecting to a computer.

Point-to-Multipoint Installation –

Unmanaged Switch

17-02-099-9336B2.indb 15 3/2/2017 1:34:03 PM

16

4. (Optional) Connect the included IR-OUT cable to the transmitter unit’s

IR-OUT port. Place the sensor on the IR-OUT cable in an unobstructed

area within clear view of the device being controlled.

Note: The IR-OUT cable receives the signal from the remote control and sends it

to the device being controlled (e.g. Blu-ray player, etc.).

5. (Optional) Using an HDMI cable, connect a local monitor to the

transmitter unit’s HDMI output port (see Optional Accessories for

available Tripp Lite HDMI cables).

6. Set the Channel Number (0 to 63 are available) on the front of the

transmitter to a desired number by pressing the Up / Down buttons. The

channel number of all transmitters in the installation MUST be different.

Note: A locking mechanism prevents the Channel Number from being

unintentionally changed. When the Channel Number is locked, hold down the Up

and Down buttons until the Channel Number starts blinking. Then navigate to the

desired Channel using the Up / Down buttons. Once the desired Channel Number

has been selected, lock the Channel Number by holding down the Up and Down

buttons until the Channel Number stops blinking.

7. Connect the RJ45 Output port on the transmitter unit to an RJ45 port

on the network switch using Cat5e/6 cable.

Note: The maximum allowable cable length from receiver to switch is 328 ft. (100 m).

Do not connect the external power supply to the transmitter at

this time. The transmitter should not be powered on until all

audio/video equipment is connected and powered on.

8. To connect an additional transmitter, repeat steps 2 through 7.

9. Connect a monitor to the receiver unit’s audio/video Output port

(See Optional Accessories for available Tripp Lite audio/video cables).

10. (Optional) Connect the serial device’s DB9 port to the receiver unit’s

serial port. Depending on the model, the serial port will be either DB9 or

3.5 mm. Models with 3.5 mm jacks include a 3.5 mm to DB9 adapter.

Models with DB9 ports require standard RS-232 DB9 cable (sold

separately) for connecting a device.

Point-to-Multipoint Installation –

Unmanaged Switch

17-02-099-9336B2.indb 16 3/2/2017 1:34:03 PM

17

11. (Optional) Connect the included IR-IN cable to the receiver unit’s IR-IN

port. Place the sensor on the IR-IN cable in an unobstructed area within

clear view of the remote control.

Note: The IR-IN cable accepts a signal from a remote control and sends it to a

device being controlled on the other end of the installation.

12. Set the Channel Number (0 to 63 are available) on the front of the

receiver to match the channel number of the transmitter whose

audio/video you want to receive by pressing the Up / Down buttons.

Note: A locking mechanism prevents the Channel Number from being

unintentionally changed. When the Channel Number is locked, hold down the Up

and Down buttons until the Channel Number starts blinking. Then navigate to the

desired Channel using the Up / Down buttons. Once the desired Channel Number

has been selected, lock the Channel Number by holding down the Up and Down

buttons until the Channel Number stops blinking.

13. Connect the RJ45 Input port on the receiver unit to an RJ45 port on the

network switch using Cat5e/6 cable.

Note: The maximum allowable cable length from receiver to switch is 328 ft.

(100 m).

Do not connect the external power supply to the receiver at

this time. The receiver should not be powered on until all

audio/video equipment is connected and powered on.

14. To connect additional receivers, repeat steps 9 through 13.

15. Power on all connected devices.

16. Connect the external power supplies to all transmitter and receiver

units in the installation, then plug the external power supplies into

Tripp Lite Surge Protectors, Uninterruptible Power Supplies (UPS) or

Power Distribution Units (PDU).

17. Once in operation, change the monitor source signal by simply

changing the channel of the corresponding receiver to match that of the

transmitter with the desired source signal.

Point-to-Multipoint Installation –

Unmanaged Switch

17-02-099-9336B2.indb 17 3/2/2017 1:34:03 PM

18

Troubleshooting

If unable to receive an acceptable image after following the installation

instructions, try the following troubleshooting tips:

1. Are the included external power supplies connected and plugged

into a working power source? For the product to function properly,

it must be connected to and receiving power from the external power

supply.

2. Was the power to the connected devices turned off prior to

installation? If not, restart all connected devices.

3. Were the connected audio/video devices powered on before the

transmitter and receiver units? If not, disconnect power from all

transmitter and receiver units, then power them back on.

4. What resolution are you trying to obtain? Make sure the installation

is within the maximum distance and resolution specs supported by the

model as referenced in the Product Features section of this manual. If

unable to obtain an acceptable image, try lowering the computer’s video

resolution or adjusting the refresh rate.

5. What type of cabling is used in the installation? Inferior cabling

can result in poor performance. It is important to use cables that

support the desired video resolution. To achieve maximum distance

and resolution, 24 AWG solid-wire Cat5e/6 cable or 23 AWG solid-wire

Cat6a cable must be used. Tripp Lite’s N202-Series Cat6 cables use

24 AWG solid wire, as do the N022-01K-GY (Cat5) and N222-01K-GY

bulk cables. The audio/video cables used must also support the desired

video resolution. Inexpensive, low quality cables may not support the

maximum resolution. It is recommended that you use the Tripp Lite

cables listed in the Optional Accessories section of this manual.

6. Test the cables to ensure they are working properly. For example,

connect the audio/video cable between a source and functioning

monitor to ensure the cable is not defective. For Cat5e/6 cable, connect

it between a computer and a network to verify it establishes a network

connection.

17-02-099-9336B2.indb 18 3/2/2017 1:34:03 PM

19

Troubleshooting

7. Check cabling for any damages that may have occurred during

installation. If a cable connector is loosened from pulling through

ceilings/wall or the cable jacket is damaged with the wiring exposed,

maximum performance will not be achieved.

8. Are the transmitter(s) and/or receiver(s) located in an area with

exposure to higher temperatures? If the product is overheated, it will

not function properly.

9. Do not set identical channel numbers for transmitters in an

Unmanaged Switch installation. Doing so will result in no signal being

displayed on monitors connected to receivers assigned to the same

channel number. If this happens, change the transmitters’ channel

numbers to unique numbers and assign the desired channel number to

the affected receivers. If audio/video does not reappear after doing this,

disconnect power from the affected transmitter and receiver units, wait

10 seconds, and reconnect the power.

10. Do not connect more than two transmitters in an unmanaged

switch installation. Unmanaged switch installations are limited to two

transmitters, with the number of receivers being limited to the number

of ports remaining on the unmanaged switch.

11. Do not connect other networking equipment to the network

switch. The B160-Series Audio/Video over IP Extenders are designed

for use with a dedicated network switch. Connecting them to a switch

used with other networking equipment will result in degraded or non-

functional product performance.

17-02-099-9336B2.indb 19 3/2/2017 1:34:03 PM

20

Warranty and Product Registration

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Tripp Lite warrants its products to be free from defects in materials and workmanship for a period of one (1) year from the

date of initial purchase. Tripp Lite’s obligation under this warranty is limited to repairing or replacing (at its sole option)

any such defective products. To obtain service under this warranty, you must obtain a Returned Material Authorization

(RMA) number from Tripp Lite or an authorized Tripp Lite service center. Products must be returned to Tripp Lite or an

authorized Tripp Lite service center with transportation charges prepaid and must be accompanied by a brief description of

the problem encountered and proof of date and place of purchase. This warranty does not apply to equipment, which has

been damaged by accident, negligence or misapplication or has been altered or modiﬁed in any way.

EXCEPT AS PROVIDED HEREIN, Tripp Lite MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of

implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL Tripp Lite BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGE. Speciﬁcally, Tripp Lite is not liable for any costs, such as lost proﬁts or revenue, loss of equipment, loss of

use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.

PRODUCT REGISTRATION

Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a

drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

FCC Notice, Class B

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device

may not cause harmful interference, and (2) this device must accept any interference received, including interference that

may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modiﬁcations to this equipment not expressly approved by Tripp Lite could void the user’s authority to

operate this equipment.

Tripp Lite has a policy of continuous improvement. Speciﬁcations are subject to change without notice.

17-02-099-9336B2.indb 20 3/2/2017 1:34:04 PM

Страница загружается...

Tripp Lite Audio/Video Инструкция по применению

Похожие модели бренда

Модели других брендов