Indesit XWDA 751680X W EU Руководство пользователя

GB

1

! This symbol reminds you to read this instruction manual.

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Care and maintenance, 4

Cutting off the water or electricity supply

Cleaning the Washer-dryerCleaning the detergent dispen-

ser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 5

General safety

Load balancing system

Disposal

Description of the Washer-dryer and

starting a wash cycle, 6-7

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 8

Push&Wash+Dry

Table of wash cycles

Personalisation, 9

Setting the temperature

Setting the drying cycle

Wash options

Detergents and laundry, 10

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Garments requiring special care

Troubleshooting, 11

Service, 12

Instructions for use

Washer-dryer

XWDA 751680

English,1

GB

ES

Español,13

BG

Български,37

HU

Magyar,25

UA

Українська,61

CIS

Русский,49

2

GB

Levelling the machine correctly will provide

it with stability, help to avoid vibrations and

excessive noise and prevent it from shifting

while it is operating. If it is placed on carpet or

a rug, adjust the feet in such a way as to allow

a sufficient ventilation space underneath the

Washer-dryer.

Connecting the electricity and

water supplies

Connecting the water inlet hose

1. Connect the inlet

hose by screwing it

to a cold water tap

using a 3/4 gas thre-

aded connection (see

figure).

Before performing the

connection, allow the

water to run freely un-

til it is perfectly clear.

2. Connect the inlet

hose to the Washer-

dryer by screwing it

onto the correspon-

ding water inlet of the

appliance, which is

situated on the top

right-hand side of the

rear part of the ap-

pliance (see figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the range of values indicated in the Technical

data table (see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

Installation

! This instruction manual should be kept in a

safe place for future reference. If the Washer-

dryer is sold, transferred or moved, make sure

that the instruction manual remains with the

machine so that the new owner is able to fa-

miliarise himself/herself with its operation and

features.

! Read these instructions carefully: they con-

tain vital information relating to the safe instal-

lation and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the Washer-dryer from its packaging.

2. Make sure that the Washer-dryer has not

been damaged during the transportation

process. If it has been damaged, contact the

retailer and do not proceed any further with

the installation process.

3. Remove the 4 pro-

tective screws (used

during transportation)

and the rubber wa-

sher with the cor-

responding spacer,

located on the rear

part of the appliance

(see figure).

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will

need them again if the Washer-dryer needs to

be moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the Washer-dryer on a flat sturdy flo-

or, without resting it up against walls, furniture

cabinets or anything else.

2. If the floor is not

perfectly level, com-

pensate for any une-

venness by tightening

or loosening the

adjustable front feet

(see figure); the angle

of inclination, measu-

red in relation to the

worktop, must not

exceed 2°.

GB

3

Connecting the drain hose

Connect the drain

hose, without bending

it, to a drain duct or

a wall drain situated

between 65 and 100

cm from the floor;

alternatively, placed

it over the edge of a

basin, sink or tub, fa-

stening the duct sup-

plied to the tap (see

figure). The free end

of the hose should

not be underwater.

! We advise against the use of hose extensions;

if it is absolutely necessary, the extension must

have the same diameter as the original hose

and must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electri-

city socket, make sure that:

• the socket is earthed and complies with all

applicable laws;

• the socket is able to withstand the maximum

power load of the appliance as indicated in the

Technical data table (see opposite);

• the power supply voltage falls within the va-

lues indicated in the Technical data table (see

opposite);

• the socket is compatible with the plug of the

Washer-dryer. If this is not the case, replace

the socket or the plug.

! The Washer-dryer must not be installed ou-

tdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to

rain, storms and other weather conditions.

! When the Washer-dryer has been installed,

the electricity socket must remain within easy

reach.

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be repla-

ced by authorised technicians.

65 - 100 cm

Warning! The company shall not be held re-

sponsible in the event that these standards are

not observed.

The first wash cycle

Once the appliance has been installed, and

before you use it for the first time, run a wash

cycle with detergent and no laundry, using the

wash cycle “Auto Clean” (see “Cleaning the

Washer-dryer”).

Technical data

Model

XWDA 751680

Dimensions

width 59.5 cm

height 85 cm

depth 54 cm

Capacity

from 1 to 7 kg for wash

programme

from 1 to 5 kg for the drying

programme

Electrical

connections

please refer to the technical

data plate fixed to the machine

Water con-

nections

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1600 rotations per

minute

Energy ra-

ted

programmes

according to

regulation

EN 50229

wash: programme 8; tem-

perature 60°C; using a load

of 7 kg.

drying: the smaller load

(2kg) must be dried by se-

lecting the “

” dryness le-

vel. The load must consist of

2 sheets, 1 pillowcase and 2

hand towels; the remainder

of the load must be dried by

selecting the “ ” dryness

level.

This appliance conforms to

the following EC Directives:

- 2004/108/EC (Electroma-

gnetic Compatibility)

- 2006/95/EC (Low Voltage)

- 2012/19/EU

4

GB

Care and maintenance

Caring for the door and drum of your

appliance

• Always leave the porthole door ajar in order

to prevent unpleasant odours from forming.

Cleaning the pump

The Washer-dryer is fitted with a self-cleaning

pump which does not require any maintenan-

ce. Sometimes, small items (such as coins or

buttons) may fall into the protective pre-cham-

ber at the base of the pump.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. Take off the cover

panel on the front of

the machine by first

pressing it in the cen-

tre and then pushing

downwards on both

sides until you can re-

move it (see figures).

2. Unscrew the lid

by rotating it anti-

clockwise (see figu-

re): a little water may

trickle out. This is

perfectly normal.

3. Clean the inside thoroughly.

4. Screw the lid back on.

5. Reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Cutting off the water and electricity

supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system

inside the Washer-dryer and help to prevent

leaks.

• Unplug the Washer-dryer when cleaning it

and during all maintenance work.

Cleaning the Washer-dryer

• The outer parts and rubber components

of the appliance can be cleaned using a soft

cloth soaked in lukewarm soapy water. Do not

use solvents or abrasives.

• The Washer-dryer has a “Auto Clean” pro-

gramme for its internal parts that must be run

with no load in the drum.

For maximum performance you may want to

use either the detergent (i.e. a quantity 10%

the quantity specified for lightly-soiled gar-

ments) or special additives to clean the Wa-

sher-dryer. We recommend running a cleaning

programme every 40 wash cycles.

To start the programme press buttons A and

B simultaneously for 5 seconds (see figure).

The programme will start automatically and

will last approximately 70 minutes. To stop the

cycle press the START/PAUSE button.

Cleaning the detergent dispenser

drawer

To remove the drawer,

press lever (1) and pull

the drawer outwards

(2) (see figure).

Wash it under running

water; this procedure

should be repeated

frequently.

2

1

2

3

A

B

GB

5

Precautions and tips

! This washer-dryer was designed and constructed in

accordance with international safety regulations. The fol-

lowing information is provided for safety reasons and must

therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance is not intended for use by persons (inclu-

ding children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concer-

ning use of the appliance by a person responsible for their

safety. Children should be supervised to ensure that they

do not play with the appliance.

– Do not dry unwashed items in the tumble dryer.

– Items that have been soiled with substances such as

cooking oil, acetone, alcohol, petrol, kerosene, spot re-

movers, turpentine, waxes and wax removers should be

washed in hot water with an extra amount of detergent

before being dried in the tumble dryer.

– Items such as foam rubber (latex foam), shower caps,

waterproof textiles, rubber backed articles and clothes or

pillows fitted with foam rubber pads should not be dried

in the tumble dryer.

– Fabric softeners, or similar products, should be used

as specified by the fabric softener instructions.

– The final part of a tumble dryer cycle occurs without heat

(cool down cycle) to ensure that the items are left at a tempe-

rature that ensures that the items will not be damaged.

WARNING: Never stop a tumble dryer before the end of

the drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not open the detergent dispenser drawer while the

machine is in operation.

• Do not touch the drained water as it may reach extreme-

ly high temperatures.

• Never force the porthole door. This could damage the

safety lock mechanism designed to prevent accidental

opening.

• If the appliance breaks down, do not under any circum-

stances access the internal mechanisms in an attempt

to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washer-dryer, make sure

the drum is empty.

• During the drying phase, the door tends to get quite hot.

• Do not use the appliance to dry clothes that have

been washed with flammable solvents (e.g.

trichlorethylene).

• Do not use the appliance to dry foam rubber or

similar elastomers.

• Make sure that the water tap is turned on during

the drying cycles.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and

to distribute the load in a uniform manner, the drum rotates

continuously at a speed which is slightly greater than the

washing rotation speed. If, after several attempts, the load is

not balanced correctly, the machine spins at a reduced spin

speed. If the load is excessively unbalanced, the Washer-

dryer performs the distribution process instead of spinning.

To encourage improved load distribution and balance, we

recommend small and large garments are mixed in the load.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2012/19/EU on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

6

GB

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents and

laundry”).

ON/OFF button: switches the Washer-dryer on and off.

PUSH&WASH+DRY button: (see “Wash cycles”).

WASH CYCLE knob: programmes the wash cycles. Du-

ring the wash cycle, the knob does not move.

OPTION buttons with indicator light: used to select the

available functions. The indicator light corresponding to the

selected function will remain lit.

TEMPERATURE button: sets the temperature or the cold

wash cycle (see “Personalisation”).

TIME-BASED DRYING button: press to select the desi-

red drying time. The selected drying time is shown bythe

indicator lights above.

LEVEL-BASED DRYING button: press to select the

desired drying level. The selected drying level is shown by

the indicator lights above.

WASH CYCLE PROGRESS indicator lights: used to

monitor the progress of the wash cycle.

The illuminated indicator light shows which phase is in

progress.

DOOR LOCKED indicator light: indicates whether the

door may be opened or not (see next page).

START/PAUSE button with indicator light: starts or tem-

porarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this

button; the corresponding indicator light will flash orange,

while the indicator light for the current wash cycle phase

will remain lit in a fixed manner. If the DOOR LOCKED

indicator light is switched off, the door may be opened

(wait approximately 3 minutes).

To start the wash cycle from the point at which it was

interrupted, press this button again.

Standby mode

This Washer-dryer, in compliance with new energy saving

regulations, is fitted with an automatic standby system

which is enabled after about 30 minutes if no activity is

detected. Press the ON-OFF button briefly and wait for the

machine to start up again.

Consumption in off-mode: 0,5 W

Consumption in Left-on: 8 W

Description of the Washer-dryer

and starting a wash cycle

Control panel

WASH CYCLE PROGRESS

indicator lights

DOOR

LOCKED

indicator light

START/PAUSE

button with indicator

light

Detergent dispenser drawer

ON/OFF

button

WASH CYCLE

knob

TEMPERATURE

button

OPTION

buttons with

indicator lights

PUSH&WASH+DRY

button

TIME-BASED

DRYING

button

LEVEL-BASED

DRYING

button

GB

7

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has

begun, the indicator lights switch on one by one to indicate

which phase of the cycle is currently in progress.

Function buttons and corresponding indicator lights

When a function is selected, the corresponding indicator

light will illuminate.

If the selected function is not compatible with the program-

med wash cycle, the corresponding indicator light will flash

and the function will not be activated.

If the selected option is not compatible with another

previously selected option, the indicator light will flash

accompanied by a buzzer (3 beeps), and only the latter

option will be activated; the indicator light corresponding to

the activated option will turn on

Door locked indicator light

When the indicator light is on, the porthole door is locked

to prevent it from being opened; make sure the indicator

light is off before opening the door (wait approximately 3

minutes).

To open the door during a running wash cycle, press the

START/PAUSE button; the door may be opened once the

DOOR LOCKED indicator light turns off.

Starting a wash cycle

Rapid programming

1. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes and wash cycles on the following page.

2. ADD THE DETERGENT. Pull out the detergent

dispenser drawer and pour the detergent into the

relevant compartments as described in “Detergents and

laundry”.

3. CLOSE THE DOOR.

4. Press the “Push&Wash+Dry” button to start the

programme.

Traditional programming

1. Turn the Washer-dryer on by pressing the ON/OFF

button. All the indicator lights will turn on for a few secon-

ds, then only the indicator lights relative to the selected

programme settings will remain lit and the START/PAUSE

indicator light will flash.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see “Personalisation”).

5. Set the drying cycle if necessary (see “Personalisation”).

6. Measure out the detergent and washing additives (see

“Detergents and laundry”).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE

button and the corresponding indicator light will remain lit

in a fixed manner in green. To cancel the set wash cycle,

pause the machine by pressing the START/PAUSE button

and select a new cycle.

9. At the end of the wash cycle the END indicator light

will switch on. The door can be opened once the DOOR

LOCK indicator light turns off (wait approximately 3 mi-

nutes). Take out your laundry and leave the appliance door

ajar to make sure the drum dries completely. Switch the

Washer-dryer off by pressing the ON/OFF button.

Wash

Rinse

Spin/Drain

Drying

End of wash cycle

END

8

GB

Wash cycles

Table of wash cycles

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-

ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

Push&Wash+Dry

This function makes it possible to start an automatic wash and drying cycle either when the machine is off without having to

press the ON/OFF button in advance, or after switching on the machine without having activated any button and/or selector

(otherwise the Push&Wash+Dry function will be deactivated). To start the Push&Wash+Dry cycle press and hold the button

for 2 seconds. The indicator lights up to show that the cycle has started. The wash and drying cycle is ideal for cotton or

synthetic fabrics, as it washes them at a temperature of 30° and a maximum spin speed of 1000 rpm. During the drying

cycle the maximum temperature is 60°C. At the end of the cycle the residual humidity will be the same as for the “ ” level.

Max recommended load 2,5 kg. (Cycle duration 210’).

How does it work?

1. Load the laundry (cotton and/or synthetic garments) and close the door.

2. Pour the detergent and/or additives.

3. Start the cycle by pressing and holding the Push&Wash+Dry button for 2 seconds. The relevant indicator light will turn

green and the door will lock (the DOOR LOCKED symbol is lit).

NB: starting the cycle through the Push&Wash+Dry button activates an automatic non-customisable wash and drying cycle

recommended for cotton and synthetic fabrics.

4. The automatic cycle can be used only for washing, excluding the drying phase. Press the Push&Wash+Dry button and

then the drying button : the drying icon of the “ ” level will switch off. Maximum load for washing-only is 3,5 kg (Cycle

duration 50’). The cycle cannot be customised further.

To open the door while an automatic cycle is under way, press the START/PAUSE button. If the DOOR LOCKED symbol is

off, the door may be opened only during the washing phase. Press the START/PAUSE button again to restart the wash cycle

from the point at which it was interrupted.

5. Once the programme is finished, the END indicator light turns on.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 50229: select wash cycle 8 with a temperature of 60°C.

2) Long wash cycle for cottons: select wash cycle 10 with a temperature of 40.

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Drying

Maximum load

for drying (Kg)

Detergents

Maximum load

for washing (Kg)

Duration of

wash cycle

Prewash

Wash

Fabric

softener

Bleach

Special

1

Sport

30° 600



3

-

 

-

3,5 55’

2

Dark

30° 800



2,5

-

 

-

4 70’

3

Anti-odour (Cotton) 60° 1000



3,5

-

 

-

3,5 110’

3

Anti-odour (Synthetic) 40° 1000



3

-

 

-

3,5 100’

4

Delicate

30° 0



1

-

 

-

1 80’

5

Wool: for wool, cashmere, etc. 40° 800



1,5

-

 

-

1,5 70’

6

Rapid 30’

30° 800



3

-

 

-

3 30’

Standard

7

Cottons with Pre-wash: extremely soiled whites. 90° 1600



5

  

-

7 170’

8

Cotton Standard 60° (1): heavily soiled whites and resistant colours.

60°

(Max. 90°)

1600



5

-

 

-

7 170’

9

Synthetic: heavily soiled resistant colours. 60° 800



3

-

 

-

3,5 110’

10

Coloured (2)

40° 1600



5

-

 

-

7 100’

11

Eco Cotton 20°: lightly soiled whites and delicate colours. 20° 1600



5

-

 

-

7 170’

12

Eco Synthetic

20° 800



5

-

 

-

7 120’

Automatic

13

Wash&Dry 45’

30° 1600



1

-

 

-

1 45’

14

AirFresh

- -



1,5

- - - -

- 30’

Partials

Rinse/Bleach - 1600



5

- -

 

7 50’

Spin + Drain - 1600



5

- - - -

7 10’

GB

9

Setting the temperature

Press the TEMPERATURE button to set the wash temperature (see Table of wash cycles).

The temperature may be lowered, or even set to a cold wash . The Washer-dryer will automatically prevent you from selec-

ting a temperature which is higher than the maximum value set for each wash cycle.

! Exception: if the 8 programme is selected, the temperature can be increased up to a value of 90°C.

Setting the drying cycle

Two different types of drying are possible: time-based and

level-based.

Press the TIME-BASED DRYING button to set the desired

drying duration: 40’- 90’- 120’ - 150’- 180’.

When the button is pressed for the first time, the selected time

will be the minimum time allowed for the set cycle.

When the machine has started the drying phase, press the TI-

ME-BASED DRYING button again to reduce the drying duration

that was set previously. The indicator lights will show the new

drying duration selected and the time remaining will consider

the time that has elapsed.

Press the LEVEL-BASED DRYING button to set the desired drying level:

Cupboard : suitable for laundry which can be put back in a cupboard without being ironed.

Hanger : ideal for clothes which do not need to be dried fully.

Iron : suitable for clothes which will need ironing afterwards. the remaining dampness softens creases, making them

easier to remove.

If your laundry load to be washed and dried is much greater than the maximum stated load (see adjacent table of wash cycles),

perform the wash cycle, and when the cycle is complete, divide the garments into groups and put some of them back in the

drum. At this point, follow the instructions provided for a “Drying only” cycle. Repeat this procedure for the remainder of the

load. A cooling-down period is always added to the end of each drying cycle.

Note: if all the drying indicator lights are off, the machine will not perform the drying cycle.

Drying only

Press button to perform the drying-only cycle. After selecting the desired cycle (compatible with the type of garments), press

button to exclude the washing phase and start the drying phase at the maximum level for the selected cycle. The drying

level and duration can be set and changed by pressing the drying buttons , .

(Not compatible with cycles 13 and 14).

Wash options

The various wash options available with this Washer-dryer will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction with the

selected wash cycle.

Stain removal

This option allows for selecting the type of dirt so as to optimally adjust the cycle for removing the stains. The following types

of dirt can be selected:

- Food, for stains caused by foodstuffs and beverages, for example.

- Work, for grease and ink stains, for example.

- Outdoor, for mud and grass stains, for example.

! The wash cycle duration varies according to the type of selected dirt.

! It cannot be used in conjunction with wash cycles 1-2-3-4-5-6-7-10-11-12-13-14- - .

Press this button to reduce the spin speed.

! It cannot be used in conjunction with wash cycles 4-13-14.

Extra Rinse

By selecting this option, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly

useful for sensitive skin.

! It cannot be used in conjunction with wash cycles 2-4-6-13-14- .

Personalisation

Table of drying times (guideline values)

Fabric

type

Load type

Max.

load

(kg)

Cupboard

Hanger Iron

Cotton

Clothing of different

sizes, Terry towels

5 250 210 190

Synthe-

tics

Sheets, Shirts, Py-

jamas, socks, etc.

3 180 130 115

Wool

Knitwear, Pullovers.

etc.

1,5 155 135 115

10

GB

Detergents and laundry

Detergent dispenser drawer

Successful washing results also depend on the correct

dose of detergent: adding too much detergent will not

necessarily result in a more efficient wash, and may in fact

cause build up on the inside of your appliance and contri-

bute to environmental pollution.

! Do not use hand washing detergents because these

create too much foam.

! Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

Open the detergent dispen-

ser drawer and pour in the

detergent or washing additi-

ve, as follows.

Compartment 1: Pre-wa-

sh detergent (powder)

Before pouring in the deter-

gent, make sure that extra

compartment 4 has been

removed.

Compartment 2: Washing detergent (powder or liquid)

If liquid detergent is used, it is recommended that the remo-

vable plastic partition A (supplied) be used for proper dosage.

If powder detergent is used, place the partition into slot B.

Compartment 3: Additives (fabric softeners, etc.)

The fabric softener must not exceed the “max” level indica-

ted on the central pin.

Extra compartment 4: Bleach

Bleach cycle

Insert the additional compartment 4 (provided) into com-

partment 1. In pouring the bleach do not exceed the

“max” level indicated on the central pin.

Perform bleaching by pouring the bleach into additional

compartment 4 and set the programme .

! Traditional bleach should be used on resistant white

fabrics, and delicate bleach for coloured and synthetics

fabrics and for wool.

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Empty all garment pockets and check the buttons.

• Do not exceed the values listed in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1.200 g

1 towel 150-250 g

Garments requiring special care

Sport (programme 1) is designed for washing lightly soiled

sports clothing (tracksuits, shorts, etc.); for best results, we

recommend not exceeding the maximum load indicated

in the “Table of wash cycles”. We recommend using liquid

detergent, and adding the amount suitable for a half-load.

Dark: use programme 2 to wash dark-coloured garments.

This programme is designed to maintain dark colours over

time. We recommend using a liquid detergent for the best

results when washing dark-coloured garments.

When you select the drying function, at the end of the

washing cycle the machine will automatically perform a

delicate drying cycle that preserves the colours of the

garments. The display will show the level “ ”.

Max. load: 2,5 kg.

Anti-odour: use programme 3 for washing garments with

bad odours (e.g. smoke, sweat, fried food). The program-

me is designed to remove bad odours while preserving the

fabric fibres. Synthetics fabrics or mixed loads should be

washed at 40°, and resistant cotton fabrics at 60°.

Delicate: use programme 4 to wash very delicate

garments. It is advisable to turn the garments inside out

before washing them. For best results, use liquid detergent

on delicate garments.

When selecting an exclusively time-based drying function,

a drying cycle is performed at the end of the wash cycle

that is particularly delicate, thanks to light handling and

appropriate temperature control of the water jet.

The recommended durations are:

1 kg of synthetic garments --> 150 min

1 kg of synthetic and cotton garments --> 180 min

1 kg of cotton garments --> 180 min

The degree of dryness depends on the load and fabric

composition.

Wool: the wool wash programme of this machine has

been tested and approved by The Woolmark Company

for the washing of wool containing garments labelled as

“hand wash” provided that the garments are washed

according to the instructions on the garment label and

those issued by the manufacturer of this washer-dryer.

(M1126)

In UK, Eire, Hong Kong and India the Woolmark trade mark

is a Certification trade mark.

Rapid 30’ (programme 6) this programme is designed to

wash lightly soiled garments at 30° (excluding wool and

silk) with a 3 kg maximum load in a short time: it only lasts

30 minutes and allows for saving time and energy

Coloured: use this programme 10 to wash bright colou-

red clothes. The programme is designed to maintain bright

colours over time.

Eco Cotton 20° (programme 11) ideal for lightly soiled

cotton loads. The effective performance levels achieved at

cold temperatures, which are comparable to washing at

40°, are guaranteed by a mechanical action which operates

at varying speed, with repeated and frequent peaks.

Eco Synthetic (programme 12) ideal for mixed loads

(cotton and synthetics) with a normal soil level. The

effective performance levels achieved at cold temperatures

are guaranteed by a mechanical action which operates at

varying speed, across set average intervals.

Wash&Dry 45’ select programme

13

for washing and

drying lightly soiled garments (Cotton and Synthetic) in

a short time. This cycle may be used to wash and dry a

laundry load of up to 1 kg in just 45 minutes. To achieve

optimum results, use liquid detergent and pre-treat cuffs,

collars and stains.

AirFresh (programme

14

) ideal cycle to refresh garments

and remove bad odours, in particular smoke, from cotton

and synthetic items in 30’ (max 1.5kg) without the washing

phase.

1

2

3

4

A

B

GB

11

Troubleshooting

Your Washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that

the problem cannot be solved easily using the following list.

Problem:

The Washer-dryer does not switch

on.

The wash cycle does not start.

The Washer-dryer does not take

in water (the indicator light for

the first wash cycle stage flashes

rapidly).

The Washer-dryer continuously

takes in and drains water.

The Washer-dryer does not drain or

spin.

The Washer-dryer vibrates a lot

during the spin cycle.

The Washer-dryer leaks.

The “Options” indicator lights and the

“start/pause” indicator light flash, while

one of the “phase in progress” indicator

lights and the “door locked” indicator

light will remain lit in a fixed manner.

There is too much foam.

Push&Wash+Dry does not activate.

The washer-dryer does not dry.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or is not making contact.

• There is no power in the house.

• The Washer-dryer door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

• The free end of the hose is under water (see “Installation”).

• The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch

the appliance off and contact the Assistance Service. If the dwelling is on one of

the upper floors of a building, there may be problems relating to water drainage,

causing the Washer-dryer to fill with water and drain continuously. Special anti-

draining valves are available in shops and help to avoid this inconvenience.

• The wash cycle does not include draining: some wash cycles require the drain

phase to be started manually.

• The drain hose is bent (see “Installation”).

• The drainage duct is clogged.

• The drum was not unlocked correctly during installation (see “Installation”).

• The Washer-dryer is not level (see “Installation”).

• The Washer-dryer is trapped between cabinets and walls (see “Installation”).

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser drawer is blocked (for cleaning instructions, see

“Care and maintenance”).

• The drain hose is not fixed properly (see “Installation”).

• Switch off the machine and unplug it, wait for approximately 1 minute and

then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

• The detergent is not suitable for machine washing (it should display the text

“for Washer-dryers” or “hand and machine wash”, or the like).

• Too much detergent was used.

• After switching on the machine a control other than Push&Wash+Dry was

activated. Switch the machine off and press the Push&Wash+Dry button.

• The appliance is not plugged into the socket, or not enough to make contact.

• There has been a power failure.

• The appliance door is not shut properly.

• All the drying indicator lights are off.

12

GB

Service

Before calling for Assistance:

• Check whether you can solve the problem alone (see “Troubleshooting”);

• Restart the programme to check whether the problem has been solved;

• If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the

guarantee certificate.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• the type of problem;

• the appliance model (Mod.);

• the serial number (S/N).

This information can be found on the data plate applied to the rear of the Washer-dryer, and can also be found on the front

of the appliance by opening the door.

ES

13

Español

! Este símbolo te recuerda que debes leer este manual de instrucciones.

Sumario

Instalación, 14-15

Desembalaje y nivelación

Conexiones hidráulicas y eléctricas

Primer ciclo de lavado

Datos técnicos

Mantenimiento y cuidados, 16

Interrumpir el agua y la corriente eléctrica

Limpiar la lavasecadora

Limpiar el cajón de detergentes

Cuidar la puerta y el cesto

Limpiar la bomba

Controlar el tubo de alimentación de agua

Precauciones y consejos, 17

Seguridad general

Sistema de equilibrado de la carga

Eliminaciones

Descripción de la lavasecadora y comienzo

de un programa, 18-19

Panel de control

Pilotos

Poner en marcha un programa

Programas, 20

Push&Wash+Dry

Tabla de programas

Personalizaciones, 21

Seleccionar la temperatura

Seleccione el secado

Opciones de lavado

Detergentes y ropa, 22

Contenedor de detergentes

Ciclo de blanqueo

Preparar la ropa

Prendas especiales

Anomalías y soluciones, 23

Asistencia, 24

ES

XWDA 751680

Manual de instrucciones

Lavasecadora

14

ES

Instalación

! Es importante conservar este manual para

poder consultarlo en cualquier momento. En

caso de venta, de cesión o de traslado, verifi-

que que permanezca junto con la lavasecado-

ra para informar al nuevo propietario sobre el

funcionamiento y brindar las correspondientes

advertencias.

! Lea atentamente las instrucciones: ellas

contienen importante información sobre la

instalación, el uso y la seguridad.

Desembalaje y nivelación

Desembalaje

1. Desembale la lavasecadora.

2. Controle que la lavasecadora no haya su-

frido daños durante el transporte. Si estuviera

dañada no la conecte y llame al revendedor.

3. Quite los 4 tornillos

de protección para el

transporte y la aran-

dela de goma con

el correspondiente

distanciador ubicados

en la parte posterior

(ver la figura).

4. Cubra los orificios con los tapones de plá-

stico suministrados con el aparato.

5. Conserve todas las piezas: cuando la lava-

secadora deba ser transportada nuevamente,

deberán volver a colocarse.

! Los embalajes no son juguetes para los

niños.

Nivelación

1. Instale la lavasecadora sobre un piso plano

y rígido, sin apoyarla en las paredes, muebles

ni en ningún otro aparato.

2. Si el piso no está

perfectamente hori-

zontal, compense las

irregularidades desen-

roscando o enroscan-

do las patas delante-

ras (ver la figura); el

ángulo de inclinación

medido sobre la su-

perficie de trabajo, no

debe superar los 2º.

Una cuidadosa nive-

lación brinda estabilidad a la máquina y evita

vibraciones, ruidos y desplazamientos durante

el funcionamiento. Cuando se instala sobre

moquetas o alfombras, regule los pies para

conservar debajo de la lavasecadora un espa-

cio suficiente para la ventilación.

Conexiones hidráulicas y eléctri-

cas

Conexión del tubo de alimentación de

agua

1. Conectar el tubo

de tubo enroscándolo

a un grifo de agua fría

con la boca roscada

de 3/4 gas (ver la

figura).

Antes de conectarlo,

haga correr el agua

hasta que esté límpi-

da.

2. Conecte el tubo de

alimentación a la lava-

secadora enroscán-

dolo en la toma de

agua correspondiente

ubicada en la parte

posterior derecha (ar-

riba) (ver la figura).

3. Controle que en el tubo no hayan pliegues

ni estrangulaciones.

! La presión de agua del grifo debe estar com-

prendida dentro de los valores contenidos en

la tabla de Datos técnicos (ver la página corre-

spondiente).

! Si la longitud del tubo de alimentación no es

la suficiente, diríjase a un negocio especializa-

do o a un técnico autorizado.

! No utilice nunca tubos ya usados.

! Utilice los suministrados con la máquina.

ES

15

Conexión del tubo de desagüe

Conecte el tubo de

desagüe, sin plegar-

lo, a un conducto de

desagüe o a una de-

sagüe de pared ubi-

cados a una distancia

del piso comprendida

entre 65 y 100 cm.;

o apóyelo en el

borde de un lavama-

nos o de una bañe-

ra, uniendo la guía

suministrada con el

aparato, al grifo (ver

la figura). El extre-

mo libre del tubo de

desagüe no debe

permanecer sumer-

gido en el agua.

! No se aconseja utilizar tubos de prolonga-

ción, si fuera indispensable hacerlo, la prolon-

gación debe tener el mismo diámetro del tubo

original y no superar los 150 cm.

Conexión eléctrica

Antes de enchufar el aparato, verifique que:

• la toma tenga la conexión a tierra y haya sido

hecha según las normas legales;

• la toma sea capaz de soportar la carga máxima

de potencia de la máquina indicada en la tabla

de Datos técnicos (ver al costado);

• la tensión de alimentación esté comprendida

dentro de los valores indicados en la tabla de

Datos técnicos (ver al costado);

• la toma sea compatible con el enchufe de la

lavasecadora. Si no es así, sustituya la toma

o el enchufe.

! La lavasecadora no debe ser instalada al aire

libre, ni siquiera si el lugar está reparado, ya que

es muy peligroso dejarla expuesta a la lluvia o

a las tormentas.

! Una vez instalada la lavasecadora, la toma de

corriente debe ser fácilmente accesible.

! No utilice prolongaciones ni conexiones múl-

tiples.

! El cable no debe estar plegado ni sufrir com-

presiones.

! El cable de alimentación debe ser sustituido

sólo por técnicos autorizados.

65 - 100 cm

¡Atención! La empresa fabricante declina toda

responsabilidad en caso de que estas normas

no sean respetadas.

Primer ciclo de lavado

Después de la instalación y antes del uso,

realice un ciclo de lavado con detergente y sin

ropa, seleccionando el programa “Auto Lim-

pieza” (ver “Limpiar la lavasecadora”).

Datos técnicos

Modelo

XWDA 751680

Dimensio-

nes

ancho 59.5 cm

altura 85 cm

profundidad 54 cm

Capacidad

de 1 a 7 kg para el lavado

de 1 a 5 kg para el secado

Conexiones

eléctricas

ver la placa de característi-

cas técnicas aplicada en la

máquina

Conexiones

hídricas

presión máxima 1 MPa

(10 bar)

presión mínima 0,05 MPa

(0,5 bar)

capacidad del cesto 52 litros

Velocidad

de

centrifuga-

do

máxima 1600 r.p.m.

Programas

de prueba

según la

directiva

EN 50229

lavado: programa 8; tempe-

ratura 60ºC; efectuado con

7 kg. de carga.

secado: el secado de la

carga menor (2kg) debe rea-

lizarse seleccionando el nivel

de secado ““

”, la carga de

ropa se debe componer de 2

sábanas, 1 funda y 2 toallas;

el secado de la carga que que-

da debe realizarse seleccionan-

do el nivel de secado “ ”.

Esta máquina cumple con lo

establecido por las siguientes

Directivas de la Comunidad:

- 2004/108/CE (Compatibili-

dad Electromagnética)

- 2012/19/EU

- 2006/95/CE (Baja Tensión)

16

ES

Mantenimiento y cuidados

Limpiar la bomba

La lavasecadora posee una bomba autolim-

piante que no necesita mantenimiento. Pero

puede suceder que objetos pequeños (mo-

nedas, botones) caigan en la precámara que

protege la bomba, situada en la parte inferior

de la misma.

! Verifique que el ciclo de lavado haya termina-

do y desenchufe la máquina.

Para acceder a la precámara:

1. quite el panel de

cobertura delantero

de la máquina pre-

sionando hacia el

centro, luego empuje

hacia abajo desde

ambos costados y

extráigalo (ver las

figuras).

2. desenrosque la

tapa girándola en

sentido antihorario

(ver la figura): es nor-

mal que se vuelque

un poco de agua;

3. limpie con cuidado el interior;

4. vuelva a enroscar la tapa;

5. vuelva a montar el panel verificando, antes

de empujarlo hacia la máquina, que los gan-

chos se hayan introducido en las correspon-

dientes ranuras.

Controlar el tubo de alimentación

de agua

Controle el tubo de alimentación al menos

una vez al año. Si presenta grietas o rajaduras

debe ser sustituido: durante los lavados, las

fuertes presiones podrían provocar roturas

imprevistas.

! No utilice nunca tubos ya usados.

Interrumpir el agua y la corriente

eléctrica

• Cierre el grifo de agua después de cada lavado.

De este modo se limita el desgaste de la

instalación hidráulica de la lavasecadora y

se elimina el peligro de pérdidas.

• Desenchufe la máquina cuando la debe

limpiar y durante los trabajos de manteni-

miento.

Limpiar la lavasecadora

• La parte externa y las partes de goma se

pueden limpiar con un paño embebido en

agua tibia y jabón. No use solventes ni pro-

ductos abrasivos.

• La lavasecadora posee un programa de

“Auto Limpieza” de su interior que se debe

realizar sin ningún tipo de carga en el cesto.

El detergente (en un 10% de la cantidad acon-

sejada para prendas poco sucias) o algunos

aditivos específicos para la limpieza de la ropa

se podrán utilizar como coadyuvantes en el

programa de lavado. Se aconseja efectuar el

programa de limpieza cada 40 ciclos de lavado.

Para activar el programa pulse simultáneamente

los botones A y B durante 5 segundos (ver la fi-

gura). El programa comenzará automáticamente

y tendrá una duración de 70 minutos aproxima-

damente. Para detener el ciclo presione el botón

START/PAUSE.

Limpiar el cajón de detergentes

Para extraer el cajón,

presione la palanca (1)

y tire hacia afuera (2)

(ver la figura).

Lávelo debajo del agua

corriente, esta limpieza

se debe realizar fre-

cuentemente.

Cuidar la puerta y el cesto

• Deje siempre semicerrada la puerta para

evitar que se formen malos olores.

1

2

3

2

1

A

B

ES

17

Precauciones y consejos

! La lavasecadora fue proyectada y fabricada en confor-

midad con las normas internacionales de seguridad. Estas

advertencias se suministran por razones de seguridad y

deben ser leídas atentamente.

Seguridad general

• Este aparato ha sido fabricado para un uso de tipo

doméstico exclusivamente.

• El aparato no debe ser empleado por personas (niños

incluidos) con capacidades físicas, sensoriales o

mentales reducidas y con experiencias y conocimien-

tos insuficientes, a menos que dicho uso no se realice

bajo la supervisión o las instrucciones de una persona

responsable de su seguridad.

Los niños deben ser vigilados para asegurarse que no

jueguen con el aparato.

- No secar prendas no lavadas.

- Las prendas sucias con sustancias como aceite de

cocina acetona, alcohol, gasolina, kerosén, quitaman-

chas, trementina, cera o sustancias para quitarlas, de-

ben lavarse con agua caliente con una cantidad mayor

de detergente antes de secarlas en la secadora.

- Objetos como la goma expandida (látex), las gorras de

ducha, los materiales textiles impermeables, los artícu-

los con un lado de goma y las prendas o cojines que

tienen partes de látex no deben secarse en la secadora.

- Suavizantes o productos similares deben emplearse

de acuerdo con las instrucciones del fabricante.

- La parte final de un ciclo de la secadora se realiza

sin calor (ciclo de enfriamiento) para garantizar que los

artículos no se dañen.

ATENCIÓN: Nunca detener una secadora antes que

finalice el programa de secado. En este caso, sacar con

rapidez todas las prendas y colgarlas para enfriarlas con

celeridad.

• No toque la máquina con los pies desnudos ni con las

manos o los pies mojados o húmedos.

• No desenchufe la máquina tirando el cable, sino toman-

do el enchufe.

• No toque el agua de descarga porque puede alcanzar

temperaturas elevadas.

• Nunca fuerce la puerta: podría dañarse el mecanismo

de seguridad que la protege de aperturas accidentales.

• En caso de avería, no acceda nunca a los mecanismos

internos para intentar una reparación.

• Controle siempre que los niños no se acerquen a la

máquina cuando está en funcionamiento.

• Si debe ser trasladada, deberán intervenir dos o más

personas, procediendo con el máximo cuidado. La

máquina no debe ser desplazada nunca por una sola

persona ya que es muy pesada.

• Antes de introducir la ropa controle que el cesto esté

vacío.

• Durante el secado la puerta tiende a calentarse.

• No seque ropa lavada con solventes inflamables

(por ej. tricloroetileno).

• No seque gomaespuma o elastómeros análogos.

• Verifique que, durante las fases de secado, el grifo de

agua esté abierto.

Sistema de equilibrado de la carga

Antes de cada centrifugado, para evitar vibraciones exce-

sivas y para distribuir la carga de modo uniforme, el cesto

realiza rotaciones a una velocidad ligeramente superior a la

del lavado. Si después de varios intentos, la carga todavía

no está correctamente equilibrada, la máquina realiza el

centrifugado a una velocidad inferior a la prevista. Cuando

existe un excesivo desequilibrio, la lavasecadora realiza la

distribución antes que el centrifugado. Para obtener una

mejor distribución de la carga y su correcto equilibrado, se

aconseja mezclar prendas grandes y pequeñas.

Eliminaciones

• Eliminación del material de embalaje:

respete las normas locales, de ese modo, los embalajes

podrán volver a ser utilizados.

• La norma Europea 2012/19/EU sobre la eliminación de

aparatos eléctricos y electrónicos, indica que los elec-

trodomésticos no deben ser eliminados de la misma

manera que los desechos sólidos urbanos.

Los aparatos en desuso se deben recoger separada-

mente para optimizar el porcentaje de recuperación y

reciclaje de los materiales que los componen e impedir

potenciales daños para la salud y el medio ambiente. El

símbolo de la papelera tachada se encuentra en todos

los productos para recordar la obligación de recolección

separada. Para mayor información sobre la correcta eli-

minación de los electrodomésticos, los poseedores de

los mismos podrán dirigirse al servicio público respon-

sable o a los revendedores.

18

ES

Contenedor de detergentes: para cargar detergentes

y aditivos (ver “Detergentes y ropa”).

Botón de ON/OFF: para encender y apagar la lavasecadora.

Botón PUSH&WASH+DRY: (ver “Programas”).

Mando de PROGRAMAS: para elegir los programas.

Durante el funcionamiento del programa el mando no se

mueve.

Botones con pilotos de OPCIÓN: para seleccionar las

funciones disponibles. El piloto correspondiente a la fun-

ción seleccionada permanecerá encendido.

Botón TEMPERATURA: para seleccionar la temperatura

o el lavado en frío (ver “Personalizaciones”).

Botón SECADO TEMPORIZADO: pulsar para seleccio-

nar el tiempo de secado; el tiempo de secado selecciona-

do es indicado por los testigos al lado.

Botón SECADO POR NIVELES: pulsar para seleccionar

los niveles de secado; el nivel de secado seleccionado es

indicado por los testigos al lado.

Pilotos DE AVANCE DEL CICLO: para seguir el estado

de avance del programa de lavado.

El piloto encendido indica la fase en curso.

Piloto PUERTA BLOQUEADA: para saber si la puerta se

puede abrir (ver la página correspondiente).

Botón con piloto START/PAUSE: se utiliza para poner en

marcha los programas o interrumpirlos momentáneamente.

Nota: Presione este botón para poner en pausa el lavado

en curso, el piloto correspondiente centelleará con color

anaranjado mientras que el de la fase en curso permane-

cerá encendido en forma fija. Si el piloto PUERTA BLO-

QUEADA está apagado, se podrá abrir la puerta (espere

3 minutos aproximadamente).

Para que el lavado se reanude a partir del momento en el

cual fue interrumpido, presione nuevamente este botón.

Modalidad de stand by

Esta lavasecadora está en conformidad con las nuevas

normativas vinculadas al ahorro energético. Está dotada

de un sistema de auto-apagado (stand by) que, en caso

de no funcionamiento, se activa aproximadamente 30

minutos. Presionar brevemente el botón ON-OFF y esperar

que la máquina se active.

Consumo en off-mode: 0,5 W

Consumo en Left-on: 8 W

Descripción de la lavasecadora y

comienzo de un programa

Botón con

piloto

START/PAUSE

Panel de control

Pilotos DE AVANCE DEL CICLO

Botón ON/OFF

Contenedor de detergentes

Mando de

PROGRAMAS

Botones con pilotos

OPCIÓN

Piloto PUERTA

BLOQUEADA

Botón

TEMPERATURA

Botón

PUSH&WASH+DRY

Botón

SECADO

TEMPORIZADO

Botón

SECADO POR

NIVELES

ES

19

Pilotos

Los pilotos suministran información importante.

He aquí lo que nos dicen:

Pilotos fase en curso

Una vez seleccionado y puesto en marcha el ciclo de

lavado deseado, las luces testigo se encenderán progresi-

vamente para indicar su estado de avance:

Botones de función y pilotos correspondientes

Seleccionando una función, el piloto correspondiente se

iluminará. Si la función seleccionada no es compatible con

el programa elegido, el piloto correspondiente centelleará

y la función no se activará. Si la opción seleccionada no

es compatible con otra opción elegida anteriormente, la

incompatibilidad se indicará con el centelleo del piloto y

una señal sonora (3 sonidos) y se activará sólo la segunda

opción, el piloto de la opción activada se iluminará.

Piloto puerta bloqueada

El piloto encendido indica que la puerta está bloqueada

impidiendo su apertura; para poder abrir la puerta es ne-

cesario que dicho piloto esté apagado (espere 3 minutos

aproximadamente). Para abrir la puerta mientras un ciclo

está en curso, presione el botón START/PAUSE; si el

piloto PUERTA BLOQUEADA está apagado, será posible

abrir la puerta.

Poner en marcha un programa

Programación rápida

1. CARGAR LA ROPA. Abra la puerta. Cargue la ropa,

cuidando no superar la cantidad de carga indicada en la

tabla de programas de la página siguiente.

2. DOSIFICAR EL DETERGENTE. Extraiga el cajón y

vierta el detergente en las cubetas correspondientes

como se explica en “Detergentes y ropa”.

3. CERRAR LA PUERTA.

4. Pulsar el botón “Push&Wash+Dry” para poner en

marcha el programa.

Programación tradicional

1. Encienda la lavasecadora pulsando el botón ON-OFF.

Todos los pilotos se encenderán durante algunos segun-

dos, luego permanecerán encendidos sólo los pilotos

correspondientes a las configuraciones para el programa

seleccionado y centelleará el piloto START/PAUSE.

2. Cargue la ropa y cierre la puerta.

3. Seleccione el programa deseado con el mando de

PROGRAMAS.

Lavado

Aclarado

Centrifugado/Descarga

Secado

Fin del Lavado

4. Fije la temperatura de lavado (ver “Personalizaciones”).

5. Seleccione el secado, si es necesario (ver “Personaliza-

ciones”).

6. Vierta detergente y aditivos (ver “Detergentes y ropa”).

7. Seleccione las funciones deseadas.

8. Ponga en marcha el programa presionando el botón

START/PAUSE y el piloto correspondiente permanecerá

encendido, fijo y de color verde. Para anular el ciclo selec-

cionado ponga en pausa la máquina presionando el botón

START/PAUSE y elija un nuevo ciclo.

9. Al final del programa se iluminará el piloto . Cuando

el piloto PUERTA BLOQUEADA se apague, será posible

abrir la puerta (espere 3 minutos aproximadamente).

Extraiga la ropa y deje la puerta semicerrada para permitir

que el cesto se seque. Apague la lavasecadora presionan-

do el botón ON/OFF.

END

20

ES

Programas

Tabla de programas

Push&Wash+Dry

Esta función permite lanzar un ciclo automático de lavado y secado, incluso con la máquina apagada, sin tener que pulsar

la tecla ON/OFF o, después de encender la máquina, sin accionar ninguna otra tecla o selector (de lo contrario, el programa

Push&Wash+Dry se desactiva). Para poner en marcha el ciclo Push&Wash+Dry, pulsar la tecla 2 segundos. El testigo encen-

dido indica que el ciclo está en marcha. El ciclo de lavado y secado es ideal para prendas de algodón y sintéticas; funciona

a una temperatura de lavado de 30° y una velocidad máxima de centrifugado de 1000 revoluciones al minuto. Durante el

secado, la temperatura máxima alcanzada es 60°C. Al finalizar el programa, la humedad residual es adecuada para el “ ”.

Carga máxima recomendada 2,5 kg. (Duración del ciclo 210’).

¿Cómo funciona?

1. Cargar la ropa (prendas de algodón y/o sintéticas) y cerrar la puerta.

2. Verter el detergente y los aditivos.

3. Lanzar el programa pulsando 2 segundos la tecla Push&Wash+Dry. El testigo correspondiente se enciende en verde y la

puerta se bloquea (símbolo de puerta bloqueada encendido).

Nota: El lanzamiento del programa con la tecla Push&Wash+Dry activa un ciclo automático de lavado y secado recomenda-

do para algodón y sintéticos no personalizable.

4. Es posible utilizar el programa automático para el solo lavado excluyendo el secado. Después de pulsar la tecla

Push&Wash+Dry, pulsar la tecla de secado . El icono de secado nivel “ ” se apaga. La carga máxima para el solo lava-

do es 3,5 kg (Duración del ciclo 50’). No es posible personalizar ulteriormente el programa.

Para abrir la puerta mientras el ciclo automático está en curso, pulsar la tecla START/PAUSE; si el símbolo de puerta

bloqueada está apagado, será posible abrir la puerta exclusivamente durante la fase de lavado. Pulsar nuevamente la tecla

START/PAUSE para reanudar el programa desde el punto en que se había interrumpido.

5. Al final del programa se iluminará el piloto END.

Para todos los Test Institutes:

1) Programa de control según la norma EN 50229: seleccione el programa 8 con una temperatura 60°C.

2) Programa algodón largo: seleccione el programa 10 con una temperatura de 40ºC.

La duración del ciclo que se indica en el visor o en el manual es una estimación calculada en base a condiciones estándar. El tiempo efectivo puede variar en función de numerosos factores como la

temperatura y la presión del agua de entrada, la temperatura ambiente, la cantidad de detergente, la cantidad y el tipo de carga, el equilibrado de la carga y las opciones adicionales seleccionadas.

Programas

Descripción del Programa

Temp.

max.

(°C)

Velo-

cidad

máx.

(r.p.m.)

Secado

Carga máxima

para el secado

(Kg)

Detergentes

Carga máxima

para el lavado

(Kg)

Duración del

ciclo de lavado

Pre-lavado

Lavado

Suavizante

Blanque-

ador

Programas Especiales

1

Sport

30° 600



3

-

 

-

3,5 55’

2

Oscuro

30° 800



2,5

-

 

-

4 70’

3

Antiolor (Algodón) 60° 1000



3,5

-

 

-

3,5 110’

3

Antiolor (Sintético) 40° 1000



3

-

 

-

3,5 100’

4

Delicados

30° 0



1

-

 

-

1 80’

5

Lana: para lana, cachemira, etc. 40° 800



1,5

-

 

-

1,5 70’

6

Rápido 30’

30° 800



3

-

 

-

3 30’

Standard

7

Prelavado Algodón: blancos sumamente sucios. 90° 1600



5

  

-

7 170’

8

Algodón Standard 60° (1): blancos y colores resistentes muy sucios.

60°

(Max. 90°)

1600



5

-

 

-

7 170’

9

Sintético: colores resistentes muy sucios. 60° 800



3

-

 

-

3,5 110’

10

De color (2)

40° 1600



5

-

 

-

7 100’

11

Eco Algodón 20°: blancos poco sucios y colores delicados. 20° 1600



5

-

 

-

7 170’

12

Eco Sintético

20° 800



5

-

 

-

7 120’

Automático

13

Lava y Seca 45’

30° 1600



1

-

 

-

1 45’

14

AirFresh

- -



1,5

- - - -

- 30’

Programas Parciales

Aclarado/Blanqueador - 1600



5

- -

 

7 50’

Centrifugado + Descarga - 1600



5

- - - -

7 10’

Страница загружается ...

Indesit XWDA 751680X W EU Руководство пользователя

Indesit XWDA 751680X W EU Руководство пользователя

Похожие модели бренда

Модели других брендов