Philco PDC840E Руководство пользователя

  • Здравствуйте! Я ознакомился с руководством пользователя для сушильной машины PHILCO PDC 840 E. Готов ответить на ваши вопросы о ее функциях, программах сушки, уходе и решении проблем. Например, я знаю, как очистить фильтры, как настроить уровень сушки и что делать при заполнении контейнера для конденсата.
  • Как очистить первичный фильтр?
    Что делать, если контейнер для конденсата полон?
    Как изменить уровень сушки?
    Как активировать блокировку от детей?
User manual
Tumble Dryer
Инструкция
по
эксплуатации
Сушильный
барабан
Návod na
používanie
Sušička
PDC 840 E
CONTENTS
Safety instructions 2
Product description 4
Accessories 5
Control panel 6
Before first use 7
Programmes 7
Using the appliance 9
Hints and tips 11
Care and cleaning 12
Troubleshooting 18
Technical information 19
Installation 19
Subject to change without notice.
SAFETY INSTRUCTIONS
Before the installation and use of the appli-
ance, carefully read the supplied instruc-
tions. The manufacturer is not responsible if
an incorrect installation and use causes in-
juries and damages. Always keep the in-
structions with the appliance for future ref-
erence.
Children and vulnerable people
safety
Warning! Risk of suffocation, injury or
permanent disability.
This appliance can be used by children
aged from 8 years and above and per-
sons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction for the opera-
tion of the appliance by a person who is
responsible for their safety.
Do not let children play with the appli-
ance.
Keep all packaging away from children.
Keep all detergents away from children.
Keep children and pets away from the
appliance door when it is open.
Cleaning and user maintenance shall not
be made by children without supervision.
Installation
Remove all the packaging.
Do not install or use a damaged appli-
ance.
Obey the installation instruction supplied
with the appliance.
Make sure that the floor where you install
the appliance is flat, stable, heat resistant
and clean.
•Do not install or use the appliance where
the temperature is less than 5°C or high-
er than 35°C.
Do not install the appliance behind a
lockable door, a sliding door or a door
with a hinge on the opposite side, where
the appliance door can not be fully
opened.
Always be careful when you move the
appliance because it is heavy. Always
wear safety gloves.
Always move the appliance vertically.
The rear surface of the appliance must
be put against the wall.
Make sure that there is air circulation be-
tween the appliance and the floor.
Make sure the carpet does not obstruct
the ventilation openings in the base of the
appliance (if applicable).
Exhaust air must not be discharged into
a flue which is used for exhausting fumes
from appliances burning gas or other
fuels. (if applicable)
If the tumble dryer is put on top of a
washing machine, use the stacking kit.
The stacking kit, available from your au-
thorized vendor, can be used only with
the appliance specified in the instruc-
tions, supplied with the accessory. Read
it carefully before installation (Refer to the
Installation leaflet).
Ensure you have good ventilation in the
installation room to avoid the back flow of
gases into the room from appliances
burning other fuels, including open fires.
The appliance can be installed as free-
standing or below the kitchen counter
with correct space (Refer to the Installa-
tion leaflet).
When the appliance is put in its perma-
nent position, check if it is fully level with
the aid of a spirit level. If it is not, adjust
the feet until it is.
2
Electrical connection
Warning! Risk of fire and electrical
shock.
The appliance must be earthed.
Make sure that the electrical information
on the rating plate agrees with the power
supply. If not, contact an electrician.
Always use a correctly installed shock-
proof socket.
Do not use multi-plug adapters and ex-
tension cables.
Make sure not to cause damage to the
mains plug and to the mains cable.
Should the appliance power supply cable
need to be replaced, this must be carried
out by our Service Centre.
Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
Do not pull the mains cable to disconnect
the appliance. Always pull the mains
plug.
Do not touch the mains cable or the
mains plug with wet hands.
This appliance complies with the E.E.C.
Directives.
Use
Warning! Risk of fire, explosion,
electric shock or damage to the
appliance
Use this appliance in a household only.
Do not change the specification of this
appliance.
The final part of the drying cycle occurs
without heat (cool down cycle) to ensure
that the items will not be damaged.
If you stop the appliance before the end
of the drying cycle, immediately remove
and spread out all items, so that the heat
can dissipate.
If you use fabric softener or similar prod-
ucts, obey the instructions on the pack-
aging.
Do not run the appliance without a filter.
Clean the lint filter before or after each
use.
Wipe away lint that has accumulated
around the appliance.
Do not dry the damaged items which
contain padding or fillings.
Do not dry items such as foam rubber
(latex foam), shower caps, waterproof
textiles, rubber backed articles and
clothes or pillows fitted with foam rubber
pads..
Before drying items that have been in
contact with substances such as cooking
oil, acetone, alcohol , petrol, kerosene,
spot removers, turpentine, waxes and
wax removers, wash them in hot water
with an extra amount of detergent.
Do not dry items in the appliance if indus-
trial chemicals have been used for clean-
ing.
Make sure that no gas lighters or match-
es have been left in the pockets of the
clothing.
Only dry fabrics which are applicable to
dry in the tumble dryer. Follow the in-
structions on the fabric label.
Do not dry not washed items in the appli-
ance.
If you have washed your laundry with a
stain remover start an extra rinse cycle
before you start the dryer.
Do not drink or prepare food with the
condensed water/distilled water. It can
cause health problems to people and
pets.
Do not sit or stand on the open door.
Obey the maximum load volume of 8 kg
(refer to the “Programme chart” chapter).
Do not dry dripping wet clothes in the
tumble dryer.
Care and Cleaning
Warning! Risk of injury or damage to
the appliance.
Before maintenance, deactivate the ap-
pliance and disconnect the mains plug
from the mains socket.
Do not use water spray and steam to
clean the appliance.
Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use abrasive products, abrasive
cleaning pads, solvents or metal objects.
3
Internal light
Warning! Risk of injury.
Visible LED radiation, do not look di-
rectly into the beam.
The type of light bulb or halogen lamp
used for this appliance, is only for
household appliances. Do not use it for
house lighting.
To replace the internal light, contact the
Service.
Disposal
Warning! Risk of injury or suffocation.
Disconnect the appliance from the mains
supply.
Cut off the mains cable and discard it.
Remove the door catch to prevent chil-
dren and pets to get closed in the appli-
ance.
Compressor
Warning! Risk of damage of the
appliance.
The compressor and its system in the
tumble dryer is filled with the special
agent which is free from fluoro-chloro-hy-
drocarbons. This system must stay tight.
The damage of the system can cause a
leakage.
PRODUCT DESCRIPTION
1 2
7
3
4
5
6
9
10
11
12
8
1
Water container
2
Control panel
3
Drum light
4
Load door (reversible)
5
Primary filter
6
Sliding button to open the heat ex-
changer door
7
Airflow slots
8
Adjustable feet
9
Heat exchanger door
10
Heat exchanger filters cover
11
Lock knob
12
Rating plate
4
ACCESSORIES
Stacking kit
Accessory name: SKP11, STA8, STA9
Available from your authorized vendor.
Stacking kit can be used only with the
washing machines specified in the leaflet.
See the leaflet attached.
Read carefully the instructions supplied with
the accessory.
Draining kit
Accessory name: DK11.
It is available from your authorized vendor
(can be attached to some types of the tum-
ble dryers)
The accessory for through draining of the
condensed water into a basin, siphon, gully,
etc. After the installation, the water contain-
er is drained automatically. The water con-
tainer must stay in the appliance.
The installed hose must be on the height
from minimum of 50 cm to maximum of 1
m from floor level. The hose cannot be in
loop. Decrease the length of the hose if
necessary.
Read carefully the instructions supplied with
the accessory.
Pedestal with the drawer
Accessory name: PDSTP10.
It is available from your authorized vendor.
To put the appliance higher at the level
which helps to easy load and remove the
laundry.
The drawer can be used for laundry storage
e.g. : towels, cleaning products and more.
Read carefully the instructions supplied with
the accessory.
Drying rack
Accessory name: RA5, RA6, RA11, RA12
It is available from your authorized vendor
(can be attached to some types of the tum-
ble dryers). Do the check with the vendor or
on the web site if the accessory is compati-
ble with your appliance.
5
Drying rack accessory let to dry safely in the
tumble dryer:
•sport shoes
•wool
soft toys
lingerie
Read carefully the instructions supplied with
the accessory.
CONTROL PANEL
1 2
356 4
1
The programme dial
2
The display
3
The Start/Pause push button
4
The function push buttons
5
The programme indicators
6
The On/Off
push button with the
Auto Off function
Display
Symbol Description
, ,
extra dryness level: minimum, moderate, maximum
,
anti-crease time: default, interval (30 min. - 120 min.)
- - -
initial laundry centrifugation (800 — 1800 rpm)
default
buzzer activated
child lock activated
time drying function activated
drain the water container indicator
6
Symbol Description
clean the primary filter indicator
clean the heat exchanger filters indicator
drying cycle phase indicator
cooling cycle phase indicator
crease guard cycle phase indicator
delay start activated
cycle time
-
time programme interval (10 min. - 2h.)
-
delay start interval (30 min. - 20h.)
BEFORE FIRST USE
Clean the tumble dryer drum with a moist
cloth or set a short programme (e.g. 30 mi-
nutes time programme) with the load of
moist cloths.
At the beginning of drying cycle (3-5 min.)
there could be a slightly higher sound level.
It is because of start of the compressor that
is normal for compressor powered applian-
ces such: refrigerators, freezers .
PROGRAMMES
Programmes
Load
1)
Properties
Available
functions
Fabric
mark
Cottons
Extra Dry 8 kg
To dry cotton pieces of clothing. Drying level:
extra dry.
all except
Time Dry-
ing
Cupboard Dry
2)
8 kg
To dry cotton pieces of clothing. Drying level:
cupboard dry.
all except
Time Dry-
ing
Iron Dry
2)
8 kg
To dry cotton pieces of clothing. Drying level:
applicable to iron.
all except
Time Dry-
ing
Extra Silent 8 kg
To gently dry cotton pieces of clothing with the
noise decreased to the minimum. The pro-
gramme can be used at night.
all except
Time Dry-
ing
Jeans 8 kg
To dry leisure clothing such as jeans, sweat-
shirts of different material thicknesses (e.g. at
the neck, cuffs and seams).
all except
Time Dry-
ing
Duvets 3 kg
To dry single or double duvet and pillows (with
feather, down or synthetic fillings).
all except
Anticrease
and Time
Drying
7
Programmes
Load
1)
Properties
Available
functions
Fabric
mark
Time 8 kg
To dry laundry with the time set by the user. The
time value must be related to the load. To dry
one item or small quantities of the laundry we
recommend to use short times.
all except
Dry Plus
and Spun
at RPM
Extra Quick
Mixed
3 kg
To dry cotton and synthetic fabrics, uses low
temperature.
all except
Time Dry-
ing
Synthetics
Extra Dry 3,5 kg
To dry synthetic pieces of clothing. Drying level:
extra dry.
all except
Time Dry-
ing
Cupboard Dry
2)
3,5 kg
To dry synthetic pieces of clothing. Drying level:
cupboard dry.
all except
Time Dry-
ing
Iron Dry 3,5 kg
To dry synthetic pieces of clothing. Drying level:
applicable to iron.
all except
Time Dry-
ing
Easy Iron
1 kg
(or 5
shirts)
To dry easy care fabrics such shirts and blou-
ses; for minimum ironing effort. The results can
be different for to the different types of fabric
and its finish. Put fabrics in the tumble dryer
straight. After the cycle, immediately remove
dried fabrics and put on a cloths hanger.
all except
Time Dry-
ing
Active Wear 2 kg
To dry outdoor pieces of clothing, technical,
sports, pile fabrics, waterproof and breathable
jackets, shell jacket teamed with a removable
fleece or inner insulation.
all except
Anticrease
and Time
Drying
Sports 2 kg
To dry sportswear, thin and light fabrics, micro-
fiber, polyester, which are not ironed.
all except
Time Dry-
ing
Silk/Lingerie 1 kg
To dry silk/lingerie with warm air and gentle
movement.
all except
Anticrease
and Time
Drying
8
Programmes
Load
1)
Properties
Available
functions
Fabric
mark
Wool 1 kg
To dry the cloths made of wool . The cloths be-
come soft and cosy. We recommend to remove
the cloths immediately after the programme end.
The wool drying cycle of this tumble drying ma-
chine has been tested and approved by The
Woolmark Company. The cycle is suitable to dry
wool garments which are labelled "hand wash"
provided that the garments are washed in a
Woolmark endorsed hand washing cycle and
tumble dried according to the instructions issued
by the manufacturer. (M1129).
To increase or to decrease the level of the re-
maining moisture of the laundry you can use the
function Dry Plus .
Dry Plus ,
Buzzer ,
Time Dry-
ing
3)
, De-
lay Start
1) maximal weight of dry clothes
2) For test institutes only:
To make a performance test use the standard programmes which are specified in the EN 61121 document. If is
necessary to correct the remaining moisture level of the laundry, adjust the programme with the Dry Plus function .
You must clean the heat exchanger filters after each 3 cycles.
3) Only with the drying rack — see chapter ACCESSORIES
USING THE APPLIANCE
Preparing the laundry
Important! Dry only the laundry applicable
to dry in the tumble dryer. Make sure if the
laundry is applicable to dry in the tumble
dryer. Do the check of the fabric mark on
the clothes.
Fabric
mark
Property
Applicable to dry in the tumble dryer
Applicable to dry in the tumble dryer
at standard temperature
Applicable to dry in the tumble dryer
at decreased temperature
Not applicable to dry in the tumble
dryer
Correctly prepare the laundry:
close zips, button up duvet covers and
attach loose ties or ribbons (e.g. ribbons
of aprons) - laundry can tangle
make sure the pockets are empty - re-
move metal items (paper clips, safety
pins, etc.).
turn items with 2 fabric layers inside out
(e.g. cotton lined anoraks, the cotton fab-
ric layer must be external).
Dry only:
cotton and linen with Cottons pro-
grammes
synthetic and mixtures with Synthetic
programmes
separately the strong coloured textiles
and the light coloured textiles - colours
can bleed
cotton jersey and knitwear only with the
applicable programmes - items can
shrink
Important! Do not put more laundry than
the maximum load which is 8kg.
Loading the laundry
1.
Pull the appliance door
9
2. Load loosely the laundry.
3. Close the appliance door.
Caution! Do not lock the laundry in
between the appliance door and
rubber seal.
Switching on the appliance
Push the On/Off button to activate or to
deactivate the appliance. When the appli-
ance is on, some indications come in to the
view on the display.
Auto Off function
To decrease the energy consumption, the
Auto Off function deactivates automatically
the appliance:
if the Start/Pause button was not pushed
in the time of 5 minutes.
after 5 minutes from the programme end.
Push the On/Off
button to activate the
appliance.
Setting a programme
Use the programme dial to set the pro-
gramme. The possible time to complete the
programme come into view on the display.
The drying time you see is related to
the load of 5 kg for cotton and jeans
programmes. For the other pro-
grammes the drying time is related to
the recommended loads. The drying
time of the cotton and jeans pro-
grammes with the load more than 5 kg
is longer.
Special functions
Together with the programme you can set
1 or more special functions.
To activate or deactivate the function push
the applicable push button.
When the function is activated the applica-
ble symbol comes into the view on the dis-
play.
The Dry Plus option
This option helps to get the laundry more
dried. There are 3 possible selections:
minimum - the default selection which is re-
lated to the programme.
moderate — the selection to get the more
dried laundry.
maximum — the selection to get the much
more dried laundry.
The Anti-crease option
Extends of 30, 60, 90 or 120 minutes the
standard anti-crease phase (30 minutes) at
the end of the drying cycle. This option pre-
vents the laundry from creases. The laundry
can be removed during the anti-crease
phase.
The Spun at RPM option
This option helps to set the best condition
to dry the laundry. If you know the initial
spin speed when you washed you can use
this option. Higher spin speed causes that
the laundry contains less water.
The Buzzer option
When the buzzer option is activated you
can hear the buzzer at the:
•cycle end
anti-crease phase start and end
cycle interruption
The buzzer option is by default always on.
You can use this option to activate or deac-
tivate the sound.
10
The Time Drying option
Operates only with the Time programme.
Lets the user to set special time of drying
programme from minimum 10 min. to maxi-
mum of 2 hours (in 10 min. steps).
The Delay Start function
Let to delay the start of a drying pro-
gramme from minimum of 30 minutes
to maximum of 20 hours.
1. Set the drying programme and func-
tions.
2. Push the Delay start button again and
again until the necessary time of the
delay come into the view on the display
(e.g.
if the programme has to start
after 12 hours.)
3.
To activate the Delay start function,
push the Start/Pause button. The time
to start decreases on the display.
Child lock function
The child lock can be set to prevent the
children to play with the appliance. The
child lock function locks all push buttons
and the programme dial (this function does
not lock Auto/Off button). To activate the
child lock function push the Dry Plus and
Anticrease buttons at the same time until
the symbol
come into view on the dis-
play. To deactivate push again the above
buttons until the symbol go out of view.
You can activate the child lock function:
before you push the Start/Pause button -
the appliance cannot start
after you push the Start/Pause button -
all the push buttons and the programme
dial are deactivated
Starting a programme
To activate the programme push the button
as on the illustration. The LED above the
button illuminates in red colour.
Change a programme
To change a programme, push the On/
Off button to deactivate appliance. Push
the
On/Off to activate the appliance and
then set the programme again.
At the end of programme
When the drying cycle is completed, the
symbol flashes on the display. If the Buzzer
function is on, an acoustic signal sounds in-
termittently for one minute.
To remove the laundry:
1.
Push the Auto/Off button for 2 seconds
to deactivate the appliance.
2.
Open the appliance door.
3. Remove the laundry.
4.
Close the appliance door.
Important! After each drying cycle:
clean the filter
drain the water container
(See chapter CARE AND CLEANING.)
HINTS AND TIPS
Ecological hints
•Do not use fabric softener to wash and
then dry. In the tumble dryer laundry be-
comes soft automatically.
Use the condensate as distilled water,
e.g. for steam ironing. If it is necessary
clean the condensate before (e.g. with a
coffee filter) to remove possible small
pieces of fluff.
Always keep the airflow slots on the bot-
tom of the appliance clear.
Use the load volumes which are specified
in the programmes chapter.
Make sure that is good airflow in the ap-
pliance installation position.
Clean the primary filter after each drying
cycle.
Clean the heat exchanger filters when the
applicable indicator comes into the view
on the control panel.
11
Spin good the laundry before drying.
Water hardness and
conductivity
Water hardness can be different for differ-
ent locations. Water hardness has an effect
on the water conductivity and the operation
of the conductivity sensor in the appliance.
If you know the value of the water conduc-
tivity you can adjust the sensor to dry with
the better results.
To change the sensor conductivity:
1.
Turn the programme dial to available
programme.
2. Push at the same time 2 buttons (see
the illustration). Hold down until one of
the symbols come into view on the dis-
play:
low conductivity <300 μS/
cm
moderate conductivity
300-600 μS/cm
high conductivity >600 μS/
cm
3. Push the button again and again until
you set necessary level (see the illustra-
tion).
4. To memorise the setting push at the
same time 2 buttons as are specified in
the point 2.
Water container full —
indication
By default the indication is always on. It
comes into the view at the end of the cycle
or when the water container is full. When
you use an external equipment to drain the
container, the indication can be off.
To activate or deactivate the indication:
1. Turn the programme dial to available
programme.
2.
Push at the same time 2 buttons (see
the illustration) and hold down until you
see the correct setting:
the indication
is off and the indi-
cator
comes into the view —
the indication
is permanently off
the indication
is on and the indi-
cator
comes into the view —
the indication
is activated
CARE AND CLEANING
Cleaning the primary filter
At the end of each cycle the indicator
(clean the primary filter) is on to tell you that
the primary filter must be cleaned.
The filter collects the fluff. The fluff oc-
curs while the cloths are dried in the
tumble dryer.
12
To clean the primary filter:
1.
Open the door.
2.
Pull the filter.
1
2
3.
Open the filter.
4.
Use a moist hand to clean the filter.
5.
If necessary clean the filter with warm
water using a brush.
Close the filter.
13
6. Remove fluff from the filter socket. For
this a vacuum cleaner can be used.
7.
Put the filter inside the filter socket.
Caution! Do not operate the tumble
dryer without the primary filter or with
damaged or blocked filter.
Important! Clean the primary filter after
each drying cycle. Clogged filter increases
the cycle time and causes higher energy
consumption.
Draining the condensed water
container
Drain the condensed water container after
each drying cycle.
If the condensed water container is full, the
programme breaks off automatically and
the indicator
drain the condensed water
container is on. To continue the pro-
gramme, drain the condensed water con-
tainer and press the start button.
To drain the condensed water contain-
er automatically you can install draining
accessory (see chapter: ACCESSO-
RIES)
To drain the condensed water container:
1.
Pull the condensed water container
and keep it in horizontal position.
2. Move the plastic connection out and
drain the condensed water container
into a sink or equivalent receptacle.
3.
Move plastic connection in and install
water container.
Warning! Risk of poisoning. The
condensed water is not applicable to
drink or to prepare food.
The condensed water can be used as
distilled water, e.g. for steam ironing. If
necessary filter the condensed water
(e.g. with a coffee filter) to remove pos-
sible residue and small pieces of fluff.
Cleaning the heat exchanger
filters
If the indicator clean the heat ex-
changer filters is on, the filters must be
cleaned.
The frequency to clean the filters is related
to the laundry type and its quantity.
If you dry with the maximum load, clean the
filters after each 3 cycles.
14
To clean the filters:
1.
Open the loading door.
2.
Move the release button on the bottom
of the door opening and open the heat
exchanger door.
3. Turn the blockage to unlock the heat
exchanger cover.
4. Lower the heat exchanger filters cover.
15
5. Lift the primary filter. Hold the heat ex-
changer filter and pull it out from the
bottom compartment.
6.
Push the hook to open the filter.
7. Use a moist hand to clean the filter. If
necessary clean the filter with warm
water using a brush.
Close the filter.
16
8. Clean the small filter from the base
9. If necessary, one time for each 6
months, remove the fluff from the heat
exchanger compartment. You can use
a vacuum cleaner.
10. Put the small filter and heat exchanger
filter back.
11. Close the heat exchanger cover.
12.
Lock the blockage until it snaps.
13. Close the heat exchanger filters cover.
14. Close the heat exchanger door.
15.
Put the primary filter.
Caution! Do not operate the tumble
dryer when the heat exchanger filters
are blocked with fluff. This could cause
the damage to the tumble dryer. This
also increases energy consumption.
Do not use sharp objects to clean the
heat exchanger compartment.
Do not operate the tumble dryer with-
out the filters.
Cleaning the drum
Warning! Disconnect the appliance
before you clean it.
Use a standard neutral soap detergent to
clean the inner surface of the drum and
drum ribs. Dry the cleaned surfaces with a
soft cloth.
Caution! Do not use abrasive materials
or steel wool to clean the drum.
Cleaning the control panel and
housing
Use a standard neutral soap detergent to
clean the control panel and housing.
Use a moist cloth to clean. Dry the cleaned
surfaces with a soft cloth.
Caution! Do not use furniture cleaning
agents or cleaning agents which can
cause corrosion to clean the appliance.
17
TROUBLESHOOTING
Troubleshooting
Problem
1)
Possible cause Remedy
The tumble
dryer does
not operate.
The tumble dryer is not connected to
mains supply.
Connect in at mains socket. Check fuse
in fuse box (domestic installation).
The loading door is opened. Close the loading door.
The Auto/Off button was not pushed. Push the Auto/Off button.
The Start/Pause button was not push-
ed.
Push the Start/Pause button.
The appliance is in the standby mode. Push the Auto/Off button.
Unsatisfactory
drying results.
Incorrect programme selection.
Do the selection of the applicable pro-
gramme.
2)
The filter is clogged.
Clean the filter.
3)
The Dry Plus function was in minimum
mode.
Change the Dry Plus function to the
moderate or maximum mode.
The heat exchanger filters are clogged.
Clean the heat exchanger filters.
3)
Too high volume of the load. Obey the maximum load volume.
The airflow grill is clogged.
Clean the airflow grill in the bottom of
the appliance.
Dirt on the inner surface of the drum. Clean the inner surface of the drum.
Too high water hardness.
Set applicable water hardness
4)
.
The door
does not
close.
The filter not locked in the position. Put the filter in the correct position.
The laundry is locked between the door
and the seal.
Put the load correctly in the drum.
Err (Error) on
the display.
You try to change the programme or the
function after the start of the cycle.
Turn the tumble dryer off and on. Make
the new selection.
The function you try to activate is not
applicable with the selected pro-
gramme.
Turn the tumble dryer off and on. Make
the new selection.
No drum light
Defective drum light.
Contact the service centre to replace
the drum light.
Abnormally
elapsing time
on the dis-
play.
The time to end is calculated on the ba-
sis of the volume and dampness of the
laundry.
The automatic procedure — this is not
the appliance malfunction.
Programme
inactive.
The water container is full.
Drain the water container
3)
, push the
Start/Pause button.
Drying cycle
too short.
Too small laundry volume.
Do the selection of time programme.
The time value must be related to the
load. To dry one item or small quantities
of the laundry we recommend to use
short times.
The laundry is too dry.
Do the selection of time programme or
higher drying level (e.g. Extra Dry )
Drying cycle
too long
5)
The filters are clogged. Clean the filters.
Too high volume of the load. Obey the maximum load volume.
18
Problem
1)
Possible cause Remedy
The laundry not spun sufficiently. Spin correctly the laundry.
Very high room temperature - this is not
the appliance malfunction.
If possible, lower the room temperature.
1) If there is an error message on the display (e.g. E51): Turn the tumble dryer off and on. Make a selection of the
new programme. Push the Start/Pause button. Does not operate? - contact the service centre and give the error
code.
2) follow the programme description — see PROGRAMMES chapter
3) see CARE AND CLEANING chapter
4) see section WATER HARDNESS in HINTS AND TIPS chapter
5) Note: After maximum 5 hours the drying cycle ends automatically (see Drying cycle complete section).
TECHNICAL INFORMATION
height x width x depth 850 x 600 x 600 mm (maximal 640 mm)
drum volume 118 l
maximum depth with the load door opened 1090 mm
maximum width with the load door opened 950 mm
adjustable height 850 mm (+ 15 mm - feet regulation)
the appliance weight 56 kg
maximum load volume
8 kg
voltage 230 V
frequency 50 Hz
necessary fuse 4 A
total power 900 W
energy efficiency class A+
energy consumption kWh/cycle
1)
2,24 kWh
annual energy consumption
2)
265 kWh
left—on mode power absorption 0,44 W
off mode power absorption 0,44 W
type of use Domestic
permitted ambient temperature + 5°C to + 35°C
1) 8 kg of cotton, centrifuged at 1000 rpm with reference to EN 61121
2) Energy consumption per year in kWh, based on 160 drying cycles of the standard cotton programme at full and
partial load, and the consumption of the low-power modes. Actual energy consumption per cycle will depend on
how the appliance is used (REGULATION (EU) No 392/2012).
INSTALLATION
Unpacking
Caution!
Before use all parts of the transport pack-
aging must be removed.
To remove the polystyrene blockages:
1. Open the load door.
2. Pull plastic hose with the polystyrene
blockages out from the drum.
19
It is possible to adjust the height of the tum-
ble dryer. To do that adjust the feet (see
picture).
15mm
Installation under a counter
The appliance can be installed as free-
standing or below the kitchen counter with
correct space (see picture).
> 850 mm
600 mm
600 mm
The load door reversal
The load door can be installed by the user
in the opposite side. It can help to easily put
and remove the laundry or if there is a limit
to install the appliance. (see separate leaf-
let).
20
/