Yamaha DTX532K/DTX562K Инструкция по применению

Бренд: Yamaha

Модель: DTX532K/DTX562K

Тип: Инструкция по применению

Это руководство также подходит для

This manual describes the standard assembly procedure for the DTX532K and DTX562K electronic drum kits. It covers assembly and wiring of the kit as

shown below. When you have completed all of the steps described, you will be ready to turn on the drum module and start playing.

This manual describes the process of assembling a drum-pad set and

drum module to an already assembled RS502 Electronic Drum Rack.

Before starting the steps below, therefore, be sure to assemble your

RS502 as described in the Owner’s Manual that came with it.

Before starting assembly, lay a drum mat (sold separately) on the floor.

Alternatively, you can place cardboard from the drum kit packaging or

the like on the floor to prevent it from being scratched. This is particu-

larly important when using the HS650A Hi-hat Stand and KP65 Kick

Pad.

The purpose of the precautions detailed below is to ensure that this electronic drum kit can be used safely without fear of injury or property damage. As a means of indicating

the severity and immediacy of any risk of injury or property damage resulting from incorrect operation, these precautions are classified as either WARNING or CAUTION. The

instructions displayed together with these precautions are extremely important in terms of ensuring safety, and therefore, they should be fully observed.

* After reading this Assembly Manual, ensure that it is kept in a safe, convenient location for future reference.

* Be sure to also read the Assembly Manuals and/or Owner’s Manuals that came with your pads and rack.

NOTICE: Usage Precautions

• When connecting and disconnecting cables, be sure to hold the plug and not the cable itself. In

addition, avoid placing heavy items on top of cables and do not allow them to touch sharp edges.

Failure to avoid these precautions can lead to cable breakage and disconnection.

• Do not climb onto the electronic drum kit and avoid placing heavy objects on it. Failure to observe

this precaution can result in malfunction.

• Avoid using or storing the electronic drum kit in very hot locations (i.e., in direct sunlight, in close

proximity to a heater, or in a closed vehicle) or in highly humid locations (i.e., in a bathroom or out-

doors in wet weather). Failure to observe this precaution can lead to warping, discoloration, mal-

function, or breakdown.

• Avoid cleaning the electronic drum kit with organic solvents, paint thinner, or alcohol as these sub-

stances can cause warping and discoloration. Instead, we recommend you remove dust using a soft

dry cloth or wipe clean using a moist, tightly-wrung cloth. If the electronic drum kit is very dirty, first

wipe the dirt away using a cloth moistened with a neutral detergent solution and tightly wrung. Fol-

lowing this, wipe away the detergent solution using a cloth soaked in water and tightly wrung.

* Yamaha Corporation reserves the right to change or modify products or specifications at any time without prior notice.

DTX532K/DTX562K Assembly Manual

Safety Precautions Please read carefully before proceeding.

Example of standard assembly

Cymbal pad

Tom pad

Tom pads

Kick pad

Snare pad

Hi-hat stand

Drum module

Real Hi-hat Pad

Electronic drum

rack

Cymbal pad

IMPORTANT

NOTICE

Failure to observe the precautions described below can result in

serious injury or even death.

• Young children using this electronic drum kit should be supervised by a guardian to eliminate any

possibility of injury.

• Holders for cymbal and tom pads have sharp tips. In order to avoid injury, therefore, you should

take special care whenever handling these components.

• The anti-slip stoppers on kick pads and foot pedals have sharp tips. In order to avoid injury, there-

fore, you should take special care whenever handling these components.

• Be sure to securely tighten nuts and other fasteners when setting up this electronic drum kit. In

addition, be sure to proceed slowly when loosening nuts. If this precaution is not observed, pads

may fall off or the rack may collapse or fall over, possibly causing injury.

• Do not setup this electronic drum kit on a slope, on an unstable platform, or on any other unsafe

surface. If this precaution is not observed, it may topple over or fall, possibly causing injury.

• Whenever setting up this electronic drum kit, ensure that cables and the like are arranged safely. If

someone were to trip on a cable, the kit could topple over and cause injury.

• Under no circumstances should this electronic drum kit be disassembled or customized. Failure to

observe this precaution can result in injury or malfunction.

• Do not sit or stand on the rack. Doing so could cause it to fall over or break, possibly causing

injury.

WARNING

Failure to observe the precautions described below can result in

injury and/or property damage.

• Mind your fingers when adjusting clamps. They can easily be crushed if care is not taken during

this operation.

• Be careful with the tips of supports, arms, screws, and the like. Fingers can easily be injured by

sharp tips if these components are not handled carefully.

• Do not place hands or feet under a kick pad or foot pedal. Doing so could result in injury.

• Do not use the electronic drum kit’s rack to hold acoustic drums. Doing so could cause clamps to

break and the drums to fall off, which in turn could lead to injury.

CAUTION

Open the boxes to reveal their contents.

After opening up the packages containing your electronic drum kit, please verify that all of the following components are present.

Assemble the RS502 Electronic Drum Rack.

For instructions on how to assemble the RS502 Electronic Drum Rack, refer to the Owner’s Manual that came with it.

Assemble the pads and the drum module to the electronic drum rack.

Components of both DTX532K & DTX562K

 XP80 Snare Pad

(x1)

 PCY135 Cymbal

Pad (x2)

 RHH135 Real

Hi-Hat Pad (x1)

 Stand base for

RHH135 (x1)

 RS502 Electronic Drum Rack (x1)

 RS502 Owner’s Manual (x1)

 HS650A Hi-hat

Stand (x1)

 KP65 Kick Pad (x1)  Nine-channel snake cable (x1)

 Stopper for

PCY135

pads (x2)

 Cable band

(x6)

 Cable band for

RHH135 (x1)

 Felt pad for

PCY135 pad (x2)

 DTX532K/DTX562K Assembly Manual (this booklet; x1)

 PCY100/135/155 Owner’s Manual (x1)

 RHH135 Owner’s Manual (x1)

 XP70/80 Owner’s Manual (x1)

 KP65 Owner’s Manual (x1)

 DTX502 Drum

Module (x1)

 Power adaptor (x1)

 Module holder (x1)  Module holder

screw (x2)

 DTX502 Owner’s Manual (x1)

Components of DTX532K only

 TP70 Tom Pad (x3)  Clamp bolt

(for XP80; x1)

 Wing bolt

(for TP70; x3)

 TP70 Owner’s Manual (x1)

Components of DTX562K only

 XP70 Tom Pad (x3)  Clamp bolt

(for XP70 or XP80; x4)

 Hi-hat clutch for

RHH135 (x1)

 Tuning key

(x1)

* May not be included

depending on your

particular area. Please

check with your Yamaha

dealer.

 Snare pad

1. Attach a clamp bolt to the snare pad and provision-

ally tighten (by five or six turns).

2. Push the snare pad onto the rack’s snare holder.

Ensure that the snare holder’s rod is fully inserted

into the snare pad’s mounting hole, and then tighten

the clamp bolt to secure the pad in place.

3. Loosen bolts A to D as shown below to adjust the

height and angle of the snare pad’s playing surface.

When correctly positioned, be sure to securely re-

tighten the bolts before proceeding to the next step.

 Tom pads

1. As with the snare pad, attach a wing bolt (DTX532K)

or clamp bolt (DTX562K) to each of the three tom

pads and provisionally tighten (by five or six turns).

2. Push each of the tom pads onto one of the rack’s

tom holders. Each time, ensure that the tom holder’s

rod is fully inserted into the tom pad’s mounting

hole, and then tighten the bolt to secure the pad in

place.

3. Loosen bolts A to C as shown below to adjust the

height and angle of each tom pad’s playing surface.

When correctly positioned, be sure to securely re-

tighten the bolts before proceeding to the next step.

XP80 Snare Pad

Tom pads

DTX532K: TP70

DTX562K: XP70

Clamp bolt (tighten in the di-

rection of the arrow)

Underside of snare pad

Push

Snare pad

Rod

Snare holder

Clamp bolt

Bolt A

Bolt C

Bolt D

Bolt B

Tom pad: TP70 Tom pad: XP70

DTX532K DTX562K

Rod

Push

Tom holderWing bolt Clamp bolt Tom holder

Rod

Bolt C

Bolt B

Bolt A

* DTX562K shown.

Assembling the snare and tom pads

U.R.G., Digital Musical Instruments Division

211POAP*.*-01A0

Printed in Vietnam

ZE16340

Continued on rear.

 Drum module

1. Secure the module holder to the bottom of the drum

module using the module holder screws.

2. Push the module holder into the holder clamp and

tighten the clamp bolt to secure it in place.



Each cymbal pad

1. Using the tuning key, loosen the stopper’s key bolt.

2. Remove the wing nut, the two felt pads, and the bolt

cover from the cymbal holder.

3. Place the stopper on the cymbal holder.

* If the key bolt was not sufficiently loosened in

Step 1 above, it may not be possible to pass the

stopper over the cymbal holder’s shaft. In such a

case, loosen the key bolt as much as possible

without removing it.

4. Replace the bolt cover.

* Turn the bolt cover to tighten it onto the threaded

section and firmly secure it in place.

5. With the stopper making full contact with the bottom

surface of the bolt cover as shown below, tighten the

stopper’s key bolt using the tuning key.

6. Place one of the felt pads removed in Step 2 on the

cymbal holder.

7. Mount the pad on the cymbal stand. Lower the pad

into place with the cymbal holder’s shaft passing

through the central hole. When mounted, the stop-

per’s pin should rest inside the pad’s smaller hole.

* If you were to play your cymbal pad without the

stopper’s pin positioned well inside the smaller

hole, the pad could rotate, causing the cable to be

pulled out. It is very important, therefore, to en-

sure that the stopper is secured as shown in Step

5 above.

8. Assemble the felt pad that came with the cymbal

pad.

9. Tighten the wing nut to secure the pad to the cymbal

holder.

A cymbal pad’s built-in sensor is located close to the

Yamaha logo found on the top surface. In order to

achieve the best performance from your pad, position

it such that the area around the logo can be easily

struck. (See the figure above.)

PCY135

Cymbal Pad

Drum module

PCY135 Cymbal Pad

Module holder

screws

Module holder

Bottom of drum

module

Front side

Clamp bolt

Drum module

module holder

Push in

Holder clamp

Tuning key

Key bolt

Stopper

Cymbal holder

Felt pads

Bolt cover

Wing nut

Cymbal holder

Stopper

Bolt cover

Threaded section

The second felt pad removed from the cymbal

holder in Step 2 above is not required for assem-

bly.

Cymbal holder

Stopper

Bolt cover

Full contact

Cymbal pad

Felt pad that

came with

cymbal

Cymbal holder

Felt pad

Bolt cover

Cymbal pad

Stopper

Wing nut

Stopper

Smaller hole

Assembling the drum module and cymbal pads

1. If a drum mat (sold separately) is not available, lay

a sheet of cardboard on the floor to prevent it from

being scratched.

2. Loosen the hi-hat stand’s wing bolt a.

3. Open up the three legs as shown below and then re-

tighten the wing bolt a to lock them in place.

4. Insert the connecting rods into the holes in the frame

as shown below.

5. As shown on the right, loosen the hi-hat clutch’s

wing bolt b and remove the hi-hat clutch.

* The hi-hat clutch is not required when assembling

the electronic drum kit in the standard fashion de-

scribed in this manual. Instead, the hi-hat clutch

that came with the RHH135 Real Hi-Hat Pad will be

used.

6. Remove the hi-hat shaft from the upper tube

7. Insert the hi-hat shaft from Step 6 as far as it will

go into the lower tube and screw in the tip.

8. Insert the upper tube over the hi-hat shaft

and tighten the wing bolt c to secure it in place with

the bottom seat approximately half way between the

top of the lower tube c and the top of the hi-hat

shaft .

9. Remove the felt pad from the top of the bottom seat.

It is not required when assembling the electronic

drum kit in the standard fashion described in this

manual.

10. Assemble the RHH135 Real Hi-hat Pad.

* For detailed instructions, refer to the Setting

Up section in the RHH135 Owner’s Manual.

Connecting

rod

Wing bolt a

Connecting

rod

Felt pad

Hi-hat clutch

Bottom

seat

Bottom

seat

Assembling the hi-hat stand

Arrange the hi-hat stand and the kick pad as shown in Example of standard assembly on the other side of this sheet.

Lay a drum mat (sold separately) on the floor underneath the hi-hat stand and the kick pad. Alternatively, you can place card-

board from the drum kit packaging or the like on the floor to prevent it from being scratched.

Connect the pads to the drum module.

Connect the output of each pad to the corresponding drum-module input.

Connect the power adaptor to the drum module.

Your electronic drum kit is now ready.

* For instructions on turning on the drum module, producing sounds, and other subsequent steps,

please refer to the Owner’s Manual that came with the module.

1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the

floor to prevent it from being scratched.

2. Remove the four wing bolts, spring washers, and flat washers from the kick pad

frame, and line up each set nearby in the order of removal.

3. Join the base section to the frame as shown on the right, and then secure it in

place by assembling the wing bolts, spring washers, and flat washers removed in

the previous step from the base side.

Frame

Base

Flat washerSpring washer

Wing bolt

Assembling the kick pad

NOTICE

1. Plug the straight ends of the nine-channel snake cable into the trigger input

jacks ([qSNARE] to [oHI-HAT] and [HI-HAT CONTROL]) on the back of the

drum module.

• When using the standard setup, the stickers on each of the snake cable’s plugs

will indicate the name of the corresponding pad.

2. Plug the L-shaped ends of the nine-channel snake cable into the corresponding

pads.

3. In the case of snare and tom pads, wrap the cables around the cable clips to pre-

vent them from being pulled out.

Excessive bending can damage pad cables. Ensure, therefore,

that these cables are not bent at an extreme angle when

wrapped around the clips.

Drum-module rear panel

Nine-channel

snake cable

Straight

plugs

L plugs

Straight plug names

(as shown on stickers)

SNARE

TOM1

TOM2

TOM3

RIDE

CRASH

KICK

HI HAT

HH CON

DTX502 jack names

1: qSNARE

2: wTOM1/!0

3: eTOM2/!1

4: rTOM3/!2

5: tRIDE

6: yCRASH

7: uKICK/i

8: oHI-HAT

9: HI HAT CONTROL

HH CON HI HAT CRASH SNARE TOM1 TOM2 TOM3 RIDEKICK

765 4321

RIDE

TOM3

TOM2

KICK

TOM1

SNARE

CRASH

HI HAT HI CON

Locations of pad jacks

NOTICE

1. Plug the power adaptor’s DC cord into the connector. Hook the power adaptor’s DC cord around

the cord clip to secure it in place.

2. Using the cable bands, secure the cables to the kit rack at the positions circled in the figure on the right. ( )

3. Plug the adaptor’s AC cord into a domestic wall socket.

Drum-module rear panel

Cord clip

connector

Yamaha DTX532K/DTX562K Инструкция по применению

Бренд: Yamaha

Модель: DTX532K/DTX562K

Тип: Инструкция по применению

Это руководство также подходит для

Скачать PDF

сообщить о нарушении

на других языках

English: Yamaha DTX532K/DTX562K Owner's manual
français: Yamaha DTX532K/DTX562K Le manuel du propriétaire
italiano: Yamaha DTX532K/DTX562K Manuale del proprietario
español: Yamaha DTX532K/DTX562K El manual del propietario
Deutsch: Yamaha DTX532K/DTX562K Bedienungsanleitung
Nederlands: Yamaha DTX532K/DTX562K de handleiding
português: Yamaha DTX532K/DTX562K Manual do proprietário
dansk: Yamaha DTX532K/DTX562K Brugervejledning
polski: Yamaha DTX532K/DTX562K Instrukcja obsługi
čeština: Yamaha DTX532K/DTX562K Návod k obsluze
svenska: Yamaha DTX532K/DTX562K Bruksanvisning
日本語: Yamaha DTX532K/DTX562K 取扱説明書
Türkçe: Yamaha DTX532K/DTX562K El kitabı
suomi: Yamaha DTX532K/DTX562K Omistajan opas
română: Yamaha DTX532K/DTX562K Manualul proprietarului

Yamaha DTX532K/DTX562K Инструкция по применению

Это руководство также подходит для

Yamaha DTX532K/DTX562K Инструкция по применению

на других языках

Похожие модели бренда