Yamaha HTR-6280 Инструкция по применению

HTR-5150

Natural Sound AV Receiver

Ampli-Tuner audio-vidéo

OWNER’S MANUAL

MODE D’EMPLOI

HTR-5150

Printed in Malaysia ID

V403350

U C A T

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

04HTR-5150-e/f cv1/4 6/28/99, 2:31 PM1

2

SAFETY INSTRUCTIONS

1 Read Instructions – All the safety and operating instructions

should be read before the unit is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the unit and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and other instructions

should be followed.

5 Water and Moisture – The unit should not be used near

water – for example, near a bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement, or near a swimming

pool, etc.

6 Carts and Stands – The unit should be used only with a

cart or stand that is recommended by the

manufacturer.

6A A unit and cart combination should be moved

with care. Quick stops, excessive force, and

uneven surfaces may cause the unit and cart

combination to overturn.

7 Wall or Ceiling Mounting – The unit should be mounted to a

wall or ceiling only as recommended by the manufacturer.

8 Ventilation – The unit should be situated so that its location

or position does not interfere with its proper ventilation. For

example, the unit should not be situated on a bed, sofa,

rug, or similar surface, that may block the ventilation

openings; or placed in a built-in installation, such as a

bookcase or cabinet that may impede the flow of air

through the ventilation openings.

9 Heat – The unit should be situated away from heat sources

such as radiators, stoves, or other appliances that produce

heat.

10 Power Sources – The unit should be connected to a power

supply only of the type described in the operating instruc-

tions or as marked on the unit.

11 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the unit.

12 Cleaning – The unit should be cleaned only as recom-

mended by the manufacturer.

13 Nonuse Periods – The power cord of the unit should be

unplugged from the outlet when left unused for a long

period of time.

14 Object and Liquid Entry – Care should be taken so that

objects do not fall into and liquids are not spilled into the

inside of the unit.

15 Damage Requiring Service – The unit should be serviced

by qualified service personnel when:

A. The power-supply cord or the plug has been

damaged; or

B. Objects have fallen, or liquid has been spilled into the

unit; or

C. The unit has been exposed to rain; or

D. The unit does not appear to operate normally or exhibits

a marked change in performance; or

E. The unit has been dropped, or the cabinet damaged.

16 Servicing – The user should not attempt to service the unit

beyond those means described in the operating instruc-

tions. All other servicing should be referred to qualified

service personnel.

17 Power Lines – An outdoor antenna should be located away

from power lines.

18 Grounding or Polarization – Precautions should be taken

so that the grounding or polarization is not defeated.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

you to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

be of sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert you to the presence

of important operating and maintenance

(servicing) instructions in the literature

accompanying the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS

UNIT TO RAIN OR MOISTURE.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

01RX-V595a-e/f1 6/24/99, 11:42 AM2

3

English

19 For US customers only:

Outdoor Antenna Grounding – If an outside antenna is

connected to this unit, be sure the antenna system is

grounded so as to provide some protection against voltage

surges and built-up static charges. Article 810 of the

National Electrical Code, ANSI/NFPA 70, provides informa-

tion with regard to proper grounding of the mast and

supporting structure, grounding of the lead-in wire to an

antenna discharge unit, size of grounding conductors,

location of antenna discharge unit, connection to grounding

electrodes, and requirements for the grounding electrode.

FCC INFORMATION (for US customers only)

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer

Electronics Group want you to get the most out of your

equipment by playing it at a safe level. One that lets the sound

come through loud and clear without annoying blaring or

distortion – and, most importantly, without affecting your

sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume levels.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If this

product is found to be the source of interference, which

can be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of the

following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfac-

tory results, please contact the local retailer authorized

to distribute this type of product. If you can not locate

the appropriate retailer, please contact Yamaha

Electronics Corp., U.S.A. 6660 Orangethorpe Ave,

Buena Park, CA 90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC,

to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation instruc-

tions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC Regula-

tions, Part 15 for Class “B” digital devices. Compliance

with these requirements provides a reasonable level of

assurance that your use of this product in a residential

environment will not result in harmful interference with

other electronic devices.

This equipment generates/uses radio frequencies and,

if not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be

connected to the grounding system of the building, as

close to the point of cable entry as practical.

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

01RX-V595a-e/f1 6/24/99, 11:42 AM3

4

SUPPLIED ACCESSORIES

ACCESSOIRES FOURNIS

• After unpacking, check that the following parts are included.

• Après le déballage, vérifier que les pièces suivantes sont incluses.

• Indoor FM Antenna

• Antenne FM intérieure

• AM Loop Antenna

• Cadre-antenne AM

• Antenna adapter

(U.S.A. and Canada models only)

• Adaptateur d’antenne

(Modèles pour les États-Unis et le

Canada seulement)

• Batteries (size AA, R6, UM-3)

• Piles (taille AA, R6, UM-3)

• Remote control

Before using the remote control, install the supplied

batteries. See page 48 for battery installation.

• Télécommande

Avant d’utiliser la télécommande, mettre les piles fournies en

place. Pour la mise en place des piles, voir page 98.

01RX-V595a-e/f1 6/24/99, 11:42 AM4

5

English

5-Channel Power Amplification

Mininum RMS Output

(0.04% THD, 20 Hz – 20 kHz)

U.S.A. and Canada models

Main: 70 W + 70 W (8 Ω)

Center: 70 W (8 Ω)

Rear: 70 W + 70 W (8 Ω)

Australia and China models

Main: 65 W + 65 W (8 Ω)

Center: 65 W (8 Ω)

Rear: 65 W + 65 W (8 Ω)

Multi-mode Digital Sound Field Processing

● Digital Sound Field Processor (DSP)

● Dolby Digital Decoder

● Dolby Pro Logic Decoder

● DTS Decoder

SUPPLIED ACCESSORIES........................................... 4

FEATURES .................................................................... 5

CAUTION ....................................................................... 6

●Introduction

FEATURES OF THE SOUND EFFECTS....................... 7

CONTROLS AND THEIR FUNCTIONS ....................... 10

●Preparation

SPEAKER SETUP ....................................................... 13

CONNECTIONS........................................................... 14

ADJUSTMENTS BEFORE USING THIS UNIT............ 21

●Basic Operation

BASIC OPERATION .................................................... 26

TUNING ....................................................................... 30

SETTING THE SLEEP TIMER..................................... 35

●Information about DSP

SOUND FIELD PROGRAM ......................................... 36

●Advanced Information

ADJUSTMENTS IN THE “SET MENU” MODE ............ 41

●Remote control

REMOTE CONTROL ................................................... 43

SETUP CODES ...........................................................49

TROUBLESHOOTING ................................................. 50

SPECIFICATIONS ....................................................... 53

LIST OF MANUFACTURERS’ CODES...................... 105

FEATURES

CONTENTS

● CINEMA DSP: Theater-like Sound

Experience by the Combination of

YAMAHA DSP Technology and Dolby

Digital, Dolby Pro Logic or DTS

● Automatic Input Balance Control for

Dolby Pro Logic decoding

● Test Tone Generator for Easier Speaker

Balance Adjustment

● Speaker Output Mode Selection

Sophisticated FM/AM Tuner

● 40-Station Random Access Preset Tuning

● Automatic Preset Tuning

● Preset Station Shifting Capability

(Preset Editing)

● 6-Channel External Decoder Input for

Other Future Formats

● Video Signal Input/Output Capability

(Including S Video Connections)

● SLEEP Timer

● Universal Remote Control with Preset

Manufacturer Codes

01RX-V595a-e/f1 6/24/99, 11:42 AM5

6

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1. To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2. Install this unit in a cool, dry, clean place – away from

windows, heat sources, sources of excessive vibration,

dust, moisture and cold. Avoid sources of humming

(transformers, motors). To prevent fire or electrical shock,

do not expose the unit to rain or water.

3. Never open the cabinet. If something drops into the set,

contact your dealer.

4. Do not use force on switches, controls or connection wires.

When moving the unit, first disconnect the power plug and

the wires connected to other equipment. Never pull the

wires themselves.

5. The openings on the cover assure proper ventilation of the

unit. If these openings are obstructed, the temperature

inside the unit will rise rapidly. Therefore, avoid placing

objects against these openings, and install the unit in a

well-ventilated area to prevent fire and damage.

Be sure to allow a space of at least 20 cm behind, 20 cm

on both sides and 30 cm above the top panel of the unit to

prevent fire and damage.

6. The voltage used must be the same as that specified on

this unit. Using this unit with a higher voltage than

specified is dangerous and may result in fire or other

accidents. YAMAHA will not be held responsible for any

damage resulting from the use of this unit with a voltage

other than that specified.

7. Digital signals generated by this unit may interfere with

other equipment such as tuners, receivers and TVs. Move

this unit farther away from such equipment if interference is

observed.

8. Always set the VOLUME control to “

” before starting the

audio source play. Increase the volume gradually to an

appropriate level after playback has been started.

9. Do not attempt to clean the unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

10. Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before concluding that

the unit is faulty.

11. When not planning to use this unit for a long period of time

(e.g., a vacation), disconnect the AC power plug from the

wall outlet.

12. To prevent lightning damage, disconnect the AC power

plug and disconnect the antenna cable when there is an

electrical storm.

13. Grounding or polarization – Precautions should be taken so

that the grounding or polarization of the unit is not

defeated.

14. AC outlet

Do not connect audio equipment to the AC outlet on the

rear panel if that equipment requires more power than the

outlet is rated to provide.

15. Voltage Selector (China model only)

The voltage selector on the rear panel of this unit must

be set for your local main voltage BEFORE plugging

into the AC main supply.

Voltages are 110/120/220/240 V AC, 50/60 Hz.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit

itself is turned off. This state is called the standby mode. In

this state, this unit is designed to consume a very small

quantity of power.

FREQUENCY STEP switch

(China model only)

Because the interstation frequency spacing differs in

different areas, set the FREQUENCY STEP switch (located

at the rear) according to the frequency spacing in your area.

Before setting this switch, disconnect the AC power plug of

this unit from the AC outlet.

IMPORTANT

Please record the serial number of this unit in the space

below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to wide

slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

01RX-V595a-e/f1 6/24/99, 11:42 AM6

7

English

FEATURES OF THE SOUND EFFECTS

Welcome to the exciting world of digital home entertainment.

This unit is one of the most complete and advanced AV

receivers available. Some of the more advanced features may

not be familiar to you, but they are easy to use. State-of-the-art

technologies such as Dolby Digital and Digital Theater Systems

(DTS) may be new to your home, but you have probably

experienced the amazing realism they bring to feature films in

theaters around the world.

To make the listening experience even more enjoyable, this unit

includes a number of exclusive, digitally created listening

environments known as digital sound fields. Choosing a sound

field program is like transporting yourself to such venues as an

outdoor arena, a European church, or a cozy jazz club. Take

some time now to read more about these features and enjoy

the new experiences this unit brings to your home theater.

Digital Sound Field Processing

What is it that makes live music so good? Today’s advanced

sound reproduction technology lets you get extremely close to

the sound of a live performance, but the chances are that you’ll

still notice something missing — the acoustic environment of

the live concert hall. Extensive research into the exact nature

of the sonic reflections that create the ambience of a large hall

has made it possible for YAMAHA engineers to bring you this

same sound to your listening room, so you’ll feel all the sound

of a live concert.

Furthermore, our technicians, armed with sophisticated

measuring equipment, have even made it possible to capture

the acoustics of a variety of actual concert halls, theaters, etc.

from around the world, to allow you to accurately re-create any

one of these live performance environments, all in your own

home.

Dolby Surround has been used in movie theaters since the mid-

seventies. It has also been available in home entertainment

systems since the late eighties and continues to be a popular

format for home theater systems. It uses four discrete channels

and five speakers to reproduce realistic and dynamic sound

effects: two main channels (left and right), a center channel for

dialog, and a rear channel for special sound effects. The rear

channel reproduces sound within a narrow frequency range.

Most video tapes and laser discs include Dolby Surround

encoding, as do many TV and cable broadcasts. The Dolby Pro

Logic decoder built into this unit employs a digital signal

processing system that stabilizes each channel for even more

accurate sound positioning than is available with standard

analog processors.

Introduction

Dolby Pro Logic

01RX-V595a-e/f1 6/24/99, 11:42 AM7

8

Dolby Digital

Dolby Digital is the next level of the Dolby Surround sound

system that was developed for 35 mm-film movies by

employing low bit-rate audio coding.

Dolby Digital is a digital surround sound system that provides

completely independent multi-channel audio to you. Dolby

Digital provides five full-range channels in what is sometimes

referred to as a “3/2” configuration: three front channels (left,

center and right), and two surround channels. A sixth bass-only

effect channel is also provided for output of LFE (low frequency

effect), or low bass effects that are independent of other

channels. (This is called the “LFE channel”.) This channel is

counted as 0.1, thus giving rise to the term 5.1 channels in

total.

Compared to Dolby Surround, which is referred to a “3/1”

system (left front, center, right front and just one surround

channel), Dolby Digital features two surround channels, called

stereo or split surrounds, each offering the same full-range

fidelity as the three front channels.

By using the built-in Dolby Digital decoder, you can experience

the dramatic realism and impact of Dolby Digital theater sound

in your home.

The wide dynamic range of sound reproduced by the five full-

range channels and precise sound orientation by digital sound

processing provides listeners with excitement and realism that

have never been experienced before.

Dolby Digital forms 5.1 channels as already mentioned, but it

can also form fewer channels, for example 2-channel stereo

and monaural. You may be able to find some 2-channel stereo

and/or monaural sources encoded with Dolby Digital in the

market.

Laser disc and DVD are home audio/video program sources

that could benefit from Dolby Digital. In the near future, Dolby

Digital will also be applied to DBS, CATV and HDTV. The

ongoing release of Dolby Digital theatrical films now underway

will provide an immediate source of Dolby Digital encoded

video software.

Manufactured under license from Dolby Laboratories. “Dolby”,

“Pro Logic” and the double-D symbol are trademarks of Dolby

Laboratories.

DTS Digital Surround

DTS (Digital Theater Systems) was developed to replace

analog soundtracks of movies with six discrete channels of

digital soundtracks, and it is now installed in many theaters

around the world. The DTS digital playback system changed

the way we experienced movies in theaters with six discrete

channels of superb digital audio.

DTS technology, through intense research and development

has made it possible to deliver similar encode/decode discrete

technology to home audio surround-sound entertainment.

DTS Digital Surround is an encode/decode system which

delivers six channels of master-quality, 20-bit audio; technically,

it is 5.1 channels, which means 5 full-range (left, center, right

and two surround) channels, plus a subwoofer (LFE) channel

(as “0.1”). It is compatible with the 5.1 speaker configurations

that are currently available for home theater systems.

The DTS Digital Surround algorithm is designed to encode the

six channels of 20-bit audio on to some laser discs, compact

discs and DVDs with considerably less data compression.

By using the DTS decoder built into this unit, you can

experience the dramatic realism and impact of the DTS-

installed theater’s high quality sound in your home.

Laser disc, compact disc and DVD are home audio formats by

which DTS can present its high-quality multi-channel audio. (In

addition to movies on laser discs, many exciting new multi-

channel music recordings will also become available in the

form of DTS-encoded compact discs.)

Manufactured under license from Digital Theater Systems, Inc.

US Pat. No. 5,451,942 and other world-wide patents issued

and pending. “DTS”, “DTS Digital Surround”, are trademarks of

01RX-V595a-e/f1 6/24/99, 11:42 AM8

9

English

CINEMA DSP: Dolby Surround + DSP / DTS + DSP

The Dolby Surround sound and DTS systems show their full

ability in a large movie theater, because movie sounds are

originally designed to be reproduced in a large movie theater

that uses a multitude of speakers. Trying to create a sound

environment similar to that of a movie theater in your home is

difficult because of the room size, material inside the walls, the

number of speakers, and so on. In other words, your listening

room is very different from a movie theater.

However, YAMAHA DSP technology allows you to create nearly

the same sound experience as that of a large movie theater in

your home by compensating for the lack of presence and

dynamics in the listening room with original digital sound fields

combined with Dolby Surround or DTS Digital Surround

sounds.

The YAMAHA “CINEMA DSP” logo indicates those programs

that are created by the combination of YAMAHA DSP

technology and Dolby Surround or DTS.

Dolby Pro Logic + 2 Digital Sound Fields

Digital sound fields are created on the presence side and the

rear surround side of the Dolby Pro Logic-decoded sound

field, respectively. They create a wide acoustic environment

and emphasize the surround effect in the room, letting you

feel as much presence as if you were watching a movie in a

popular Dolby Stereo theater.

Refer to pages 36 to 37 for the DSP program.

CINEMA DSP

Dolby Digital or DTS + 3 Digital Sound Fields

Digital sound fields are created on the presence side and the

independent left and right surround sides of the Dolby Digital-

decoded or DTS-decoded sound field, respectively. They

create a wide acoustic environment and strong surround

effect in the room without losing high-channel separation. With

the wide dynamic range of Dolby Digital or DTS sound, this

sound field combination lets you feel as if you were watching

a movie in the newest Dolby Digital theater or DTS-installed

theater. This is the most ideal home theater sound at the

present time.

Refer to pages 36 to 37 for the DSP program.

01RX-V595a-e/f1 6/24/99, 11:42 AM9

10

STANDBY/ON

TAPE/MD MON

/EXT. DECODER

–dB

0

2

4

8

12

18

20

22

40

80

1

0

2

3

4

55

4

3

2

1

2

3

4

3

2

1

BALANCETREBLEBASS

VIDEO AUX

PHONES

SPEAKERS

A

B

ON OFF

PROGRAM

INPUT

VCR • V

–

AUX • TV

/

DBS • DVD

/

LD • CD • TUNER • PHONO

VOLUME

L

8 VIDEO VIDEO

AUDIO R

A

/

B

/

C

/

D

/

E1 2

3

4

5

678

TUNING

MODE

MEMORY EDIT

FM/AM

DOWN

TUNING

UP

INPUT MODE

0

1

0

2

3

4

5 RL 5

4

3

2

1

TIME/

LEVEL

SET

MENU

EFFECT

55

MAN’L

/

AUTO FM AUTO

/

MAN’L MONO

CONTROLS AND THEIR FUNCTIONS

FRONT PANEL

1

STANDBY/ON

Press this switch to turn on the power of this unit. Press it

again to set this unit in the standby mode.

Standby mode

In this state, this unit consumes a very small quantity of

power to receive infrared-signals from the remote control.

2 Remote control sensor

This receives signals from the remote control.

3 Display

This shows various information. (Refer to page 12 for details.)

4 MEMORY (MAN’L/AUTO FM)

Press this button to store the broadcasting stations.

When this button is pressed and held for more than three

seconds, automatic preset tuning begins.

5 EDIT

This button is used to exchange the assigment of two preset

stations with each other.

6 TUNING MODE (AUTO/MAN’L MONO)

Press this button to switch the tuning mode to automatic or

manual. To select the automatic tuning mode, press this button

so that the “AUTO TUNING” indicator lights up on the display.

To select the manual tuning mode, press this button so that the

“AUTO TUNING” indicator goes off.

7 FM/AM

Press this button to switch the reception band between FM and

AM.

8 TUNING UP/DOWN

This button is used for tuning. Press the UP side to tune in to

higher frequencies, and press the DOWN side to tune in to

lower frequencies.

9 TAPE/MD MON / EXT. DECODER

Press this button to play a tape or an MD. The “TAPE/MD

MON” indicator lights up on the display.

When you press the button next, the “TAPE/MD MON” indicator

goes off, “EXT. DECDR” appears on the display and you can

play the signal connected to the EXTERNAL DECODER

INPUT terminals.

0 INPUT

Turn this selector to select the input source (VCR, VIDEO AUX,

TV/DBS, DVD/LD, CD, TUNER, PHONO) that you want to

listen to or watch.

The name of the selected input source appears on the display.

Refer to pages 43 to 48 for the remote control.

01RX-V595a-e/f1 6/24/99, 11:42 AM10

11

English

q INPUT MODE

This button switches between the DVD/LD and TV/DBS input

signal modes.

w VOLUME

This control is used to raise or lower the volume level.

e PHONES jack

When you use headphones, connect the headphones to the

PHONES jack. You can listen to the sound to be output from

the main speakers through the headphones.

When using headphones only, set both SPEAKERS A and B to

the OFF position and switch off the digital sound field processor

(so that no DSP program name appears on the display) by

pressing EFFECT.

r SPEAKERS

Set A or B (or both A and B) to the ON position for the main

speaker system (connected to this unit) that you want to use.

Set the button(s) for the main speaker system you don’t want to

use to the OFF position.

t A/B/C/D/E

Press this button to select one of a group (A to E) of preset

stations.

y Preset station number selector

Each of these buttons selects a preset station number (1 to 8).

u Tone controls

These controls are only effective for the sound from the main

speakers.

BASS

Use this control to increase or decrease the low-frequency

response. The “0” position produces a flat response.

TREBLE

Use this control to increase or decrease the high-frequency

response. The “0” position produces a flat response.

i BALANCE

This control is only effective for the sound from the main

speakers.

Turn the control to adjust the balance of the output volume to

the left and right speakers to compensate for sound imbalance

caused by the speaker location or listening room conditions.

o TIME/LEVEL

Press this button to select the item in the TIME/LEVEL mode.

p +/–

These buttons are used to adjust the settings of the SET MENU

mode and the TIME/LEVEL mode. In the TIME/LEVEL mode,

press + to increase the delay time or speaker output level.

Press – to decrease the delay time or speaker output level.

a SET MENU

Press this button to select functions in the SET MENU mode.

s PROGRAM selector

Press

or to select a DSP program.

The name of the selected program appears on the display.

d EFFECT

Press this button once to switch the effect speakers (center and

rear) on or off. If you turn off the effect by using EFFECT, all

Dolby Digital and DTS audio signals are directed to the main

left and right channels. In that case, the left and right channel

signal levels may not match.

f VIDEO AUX terminals

Connect an auxiliary video or audio input source such as a

camcorder to these terminals. If the connected video unit has

an S video output terminal, connect it to the S VIDEO terminal

to obtain a high-resolution picture. The source connected to

these terminals can be selected by INPUT.

01RX-V595a-e/f1 6/24/99, 11:42 AM11

12

1 Multi-information display

This displays various information, for example the station

frequency, preset station number and name of the selected

input source.

2 MEMORY indicator

When MEMORY is pressed, this indicator flashes for about five

seconds. During this period, the displayed station can be

stored in the memory.

3 AUTO TUNING indicator

This lights up when the unit is in the automatic tuning mode.

4 TAPE/MD MON indicator

This lights up when the tape deck (or MD recorder, etc.) is

selected as the input source by pressing TAPE/MD MON / EXT.

DECODER on the front panel or TAPE/MD on the remote control.

5 STEREO indicator

This lights up when an FM stereo broadcast with sufficient

signal strength is being received.

6 Signal-level indicator

This indicates the signal level of the station being received.

If multipath interference is detected, the indication decreases.

DISPLAY PANEL

7

indicators

Either “dts” indicator lights up when the built-in DTS decoder is

turned on.

The red “dts” indicator lights up when playing a CD or LD

encoded with DTS.

The orange “dts” indicator lights up when playing a DVD

encoded with DTS.

* An orange “dts” indicator may light up when playing a CD or

LD encoded with DTS after playing a video-CD or DVD on a

DVD/LD combi-player.

8 , and indicators

“

” lights up when the built-in Dolby Digital decoder is

on and the signals of the selected source encoded with Dolby

Digital are not in 2-channel. “ ” lights up when the built-in

digital sound field processor is on, and “

” lights up

when the built-in Dolby Pro Logic decoder is on. Depending on

the selected DSP program, both “

” and “ ”, or

both “

” and “ ” will light up.

9 SLEEP indicator

This lights up while the built-in SLEEP timer is functioning.

01RX-V595a-e/f1 6/24/99, 11:42 AM12

13

English

SPEAKER SETUP

This unit is designed to provide the best sound-field quality with

a 5-speaker configuration, using main speakers, rear speakers

and a center speaker.

The main speakers are used for the main source sound plus

the effect sounds. They will probably be the speakers from

your present stereo system. The rear speakers are used for

the effect and surround sounds, and the center speaker is for

the center sounds (dialog, vocals, etc.). If for some reason it is

not practical to use a center speaker, you can do without it.

Best results, however, are obtained with the full system.

The main speakers should be high-performance models and

have enough power-handling capacity to accept the maximum

output of your audio system.

The other speakers do not have to be equal to the main

speakers. For precise sound localization, however, it is ideal to

use high-performance models that can reproduce sounds over

the full range for the center speaker and the rear speakers.

Use of a subwoofer expands your sound field

It is also possible to further expand your system with the

addition of a subwoofer. The use of a subwoofer is effective

not only for reinforcing bass frequencies from any or all

channels, but also for reproducing the LFE (low frequency

effect) sound with high fidelity when playing back a source that

is Dolby Digital or DTS-decoded. The YAMAHA Active Servo

Processing Subwoofer System is ideal for natural and lively

bass reproduction.

SPEAKERS TO BE USED

SPEAKER PLACEMENT

Refer to the following diagram when you place the speakers.

Main: The position of your present stereo speaker

system.

Rear: Behind your listening position, facing slightly

inward. Nearly 1.8 m (approx. 6 feet) up from the

floor.

Center: Precisely between the main speakers. (To avoid

interference with TV sets, use a magnetically

shielded speaker.)

Subwoofer: The position of the subwoofer is not as critical,

because low bass tones are not highly directional.

Rear

speaker (R)

Main

speaker (R)

Center speaker

Subwoofer

Main

speaker (L)

Rear

speaker

(L)

Note: If the center speaker (principally, it reproduces dialog, vocals, etc.) is not used, the sound will be output from the left and

right main speakers. In that case, be sure to select the NONE position for “CNTR” in the SET MENU mode. (See page 21

for details.)

01RX-V595a-e/f2 6/24/99, 11:42 AM13

14

AC OUTLET(S) (SWITCHED)

U.S.A., Canada and China models ....................... 2 OUTLETS

Australia model .........................................................1 OUTLET

Use these to connect the power cords from your components to

this unit.

The power to the AC OUTLET(S) is controlled by this unit’s

STANDBY/ON or the provided remote control’s POWER and

STANDBY. These outlets will supply power to any connected

component whenever this unit is turned on.

The maximum power (total power consumption of components)

that can be connected to the AC OUTLET(S) is 100 watts.

CONNECTIONS

Never plug in this unit and other components until all connections have been completed.

CONNECTIONS WITH OTHER COMPONENTS

Use RCA-type pin plug cables for connecting audio/video components with the exception described later.

When making connections between this unit and other components, be sure all connections are made correctly, that is to say L

(left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.

* If you have YAMAHA components numbered as !, #, $, etc. on the rear panel, connections can be made easily by making sure

to connect the output (or input) terminals of each component to the same-numbered terminals of this unit.

.

Turntable Monitor TV

DVD player,

LD player, etc.

CD player Tape deck,

MD recorder, etc.

TV/DBS tuner VCR

(Video cassette recorder)

To AC outlet

(U.S.A. model)

GND terminal (for turntable use)

Connecting the ground (earth) wire of the turntable to the GND terminal will normally minimize hum, but in some cases, better

results may be obtained with the ground wire disconnected.

01RX-V595a-e/f2 6/24/99, 11:42 AM14

15

English

CONNECTING TO DIGITAL (COAXIAL AND/OR OPTICAL) TERMINALS

If your DVD (LD) player, TV/DBS tuner, etc. are equipped with

coaxial or optical digital audio signal output terminals, they can

be connected to this unit’s COAXIAL and/or OPTICAL digital

signal input terminals.

Digital audio signals are transmitted with less loss than analog

audio signals. In addition, digital audio signal connections are

necessary, especially for an LD player or a DVD player, to send

signals encoded with Dolby Digital or DTS to this unit.

To make a connection between optical digital audio signal

terminals, remove the cover from each terminal, and then

connect them by using a commercially available optical fiber

cable that conforms to EIAJ standards. Other cables might not

function correctly.

Even if you connect an audio/video unit to the COAXIAL (or

OPTICAL) terminal of this unit, you must keep the unit

connected with the same-named analog audio signal terminals

of this unit, because a digital signal cannot be recorded by a

tape deck, MD recorder or VCR connected to this unit. You can

easily switch the selection of input signals between “digital” and

“analog.” (See page 28 for details.)

Notes

• When connecting an audio/video unit to both the digital and

analog terminals of this unit, make sure to connect between

both terminals of the same name.

• Be sure to attach the covers when the OPTICAL terminals

are not being used in order to protect them from dust.

• The input signal from the DVD/LD input terminals is selected

in the following order of priority with the input mode set to the

AUTO position:

1 COAXIAL terminal

2 OPTICAL terminal

3 Analog terminal

• If the DIGITAL OUT data of the player has been processed in

any way, you may not be able to perform DTS playback even

if you make a digital connection between this unit and the

player.

• All digital audio signal input terminals are applicable to

sampling frequencies of 32 kHz, 44.1 kHz and 48 kHz.

No sound will be generated when connecting your LD

player’s Dolby Digital RF signal output terminal directly to

this unit’s COAXIAL DVD/LD digital signal input terminal.

DVD or LD player*

* If your LD player has a Dolby Digital RF signal

output terminal, be sure to use the RF

demodulator (separately purchased).

TV/DBS tuner

(U.S.A. model)

01RX-V595a-e/f2 6/24/99, 11:42 AM15

16

S

CONNECTING TO S VIDEO TERMINALS

If you have a VCR and a monitor equipped with “S” (high-

resolution) video terminals, those terminals can be connected

to this unit’s S VIDEO terminals. Connect the VCR’s “S” video

input and output terminals to this unit’s S VIDEO VCR OUT and

IN terminals, respectively, and connect the monitor’s “S” video

input terminal to this unit’s S VIDEO MONITOR OUT terminal.

Otherwise, connect the VCR’s composite video terminals to this

unit’s composite video terminals, and connect the monitor’s

composite video input terminal to this unit’s composite

MONITOR OUT terminal.

In addition, if you have a DVD or LD player equipped with an

“S” video terminal, connect the DVD/LD player’s “S” video

output terminal to this unit’s S VIDEO DVD/LD terminal.

Note

If video signals are sent to both S VIDEO input and com-

posite input terminals, the signals will be sent to their

respective output terminals.

S VIDEO terminals

This unit provides you with S VIDEO terminals in addition

to standard VIDEO terminals.

S VIDEO terminals transmit video signals separated into

luminance (Y) signals and color (C) signals. In comparison

with S VIDEO terminals, standard VIDEO terminals transmit

“composite” video signals.

Monitor TV

S

S S S

S

Camcorder

CONNECTING TO VIDEO AUX TERMINALS (ON THE FRONT PANEL)

These terminals are used to connect any video input source such as a camcorder to this unit.

DVD/LD player

S VIDEO cable

VCR

01RX-V595a-e/f2 6/24/99, 11:42 AM16

17

English

CONNECTING TO AN EXTERNAL DECODER

This unit is equipped with additional 6-channel audio signal

input terminals for inputting signals from an external decoder to

this unit.

Connect the 6-channel audio signal output terminals of the

decoder to the EXTERNAL DECODER INPUT terminals of this

unit.

Notes

• When signals input to these terminals are selected, the digital

sound field processor cannot be used.

• The settings of “CNTR”, “REAR”, “MAIN” and “BASS” in the

SET MENU mode have no effect on the signals input to these

terminals. The setting of “M.LVL” is effective. (Refer to

page 21 for details.)

• Adjustment of the output level of the center speakers, rear

speakers and subwoofer is effective when the signals input to

these terminals are selected as the input source. (Refer to

page 39 for details.)

External decoder with

6-channel discrete

outputs

(U.S.A. model)

WARNING

Do not change the IMPEDANCE SELECTOR switch setting

while the power to this unit is on, otherwise this unit may be

damaged.

If this unit fails to turn on when the STANDBY/ON switch is

pressed, the IMPEDANCE SELECTOR switch may not be

fully set to either end. If so, set the switch to either end fully

when this unit is in the standby mode.

Select the position whose requirements your speaker system

meets.

(Upper position)

Main: If you use one pair of main speakers, the impedance of

each speaker must be 4 Ω or higher.

If you use two pairs of main speakers, the impedance

of each speaker must be 8 Ω or higher.

Center: The impedance of the speaker must be 6 Ω or higher.

Rear: The impedance of each speaker must be 6 Ω or

higher.

(Lower position)

Main: If you use one pair of main speakers, the impedance of

each speaker must be 8 Ω or higher.

If you use two pairs of main speakers, the impedance

of each speaker must be 16 Ω or higher.

The impedance of each speaker must be 8 Ω or

higher.

Center: The impedance of the speaker must be 8 Ω or higher.

Rear: The impedance of each speaker must be 8 Ω or

higher.

IMPEDANCE SELECTOR SWITCH

IMPEDANCE SELECTOR

(U.S.A. model)

01RX-V595a-e/f2 6/24/99, 11:43 AM17

18

Note

Use speakers with the specified impedance shown on the

rear panel of this unit.

Main speaker connections

One or two speaker systems can be connected to this unit. If

you use only one speaker system, connect it to either of the

SPEAKERS A or B terminals.

Rear speaker connections

A rear speaker system can be connected to this unit. Place

them to the rear of your listening position.

Center speaker connection

A center speaker can be connected to this unit. Place it on or

under the TV.

Subwoofer connection

You may wish to add a subwoofer to reinforce low frequencies

or to output low bass sound from the subwoofer channel.

If you have a subwoofer with built-in amplifier, including the

YAMAHA Active Servo Processing Subwoofer System, connect

the SUBWOOFER OUTPUT terminal of this unit to the input

terminal of the subwoofer system.

CONNECTING SPEAKERS

Rear speakers

Subwoofer system

Center speaker

Right

Left

Main speakers A Main speakers B

Right

Left

Right Left

(U.S.A. model)

01RX-V595a-e/f2 6/24/99, 11:43 AM18

19

English

How to connect

Connect the SPEAKERS terminals to your speakers with wire of the proper gauge, cut as short as possible. If the connections are

faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct, that is the + and –

markings are observed. If these wires are reversed, the sound will be unnatural and lack bass.

Caution

Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could

damage the unit and/or speakers.

Connecting to the MAIN SPEAKERS terminals

Red: positive (+)

Black: negative (–)

1 Unscrew the knob.

2 Remove approx. 5 mm

(1/4”) of insulation from

each of the speaker

wires and insert one

bare wire into each

terminal.

3 Tighten the knob to

secure the wire.

1 Press the tab.

2 Remove approx. 5 mm

(1/4”) of insulation from

each of the speaker

wires and insert one

bare wire into each

terminal.

3 Release the tab to

secure the wire.

1

2

3

2

3

1

Connecting to the REAR and CENTER

SPEAKERS terminals

Red: positive (+)

Black: negative (–)

Banana plug connections are also possible. Simply insert the

banana plug connector into the corresponding terminal.

01RX-V595a-e/f2 6/24/99, 11:43 AM19

20

Connecting the AM loop antenna

• The AM loop antenna should be placed away from this unit. The antenna may be hung on a wall.

• The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

1

2

3

ANTENNA CONNECTIONS

Each antenna should be correctly connected to the designated terminals, referring to the following diagram.

Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal

strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor

reception quality, an outdoor antenna may result in improvement.

GND terminal

For maximum safety and minimum interference, connect the

GND terminal to a good earth ground. A good earth ground

is a metal stake driven into moist earth.

2 Attach the loop antenna to the

antenna stand.

Outdoor

FM antenna

75-ohm/300-ohm

antenna adapter

75-ohm coaxial cable

75-ohm/300-ohm

antenna adapter

300-ohm feeder

Ground

AM loop

antenna

(included)

Outdoor AM antenna

* If you cannot obtain good

reception with the AM loop

antenna, connect 5 m to

10 m of vinyl covered wire

to the AM ANT terminal

and extend it outdoors

from a window. (Be sure

to also connect the AM

loop antenna at this time.)

Indoor FM antenna

(included)

* Firmly insert the

connector into the FM

ANT terminal.

Loop antenna

Antenna stand

* You may be unable to obtain good FM radio

reception depending on your local

conditions (distance from the broadcast

station, interposing buildings and

mountains, etc.). Consult your dealer or

authorized service center and be sure to

install an antenna that suits your local

conditions.

Install the special FM outdoor antenna in a

high place as far away from any roads as

possible to avoid being affected by

automobile ignition noise.

1 1 Press the tab and unlock the terminal hole.

2 Connect the AM loop antenna lead wires to the

AM ANT and GND terminals.

3 Return the tab to its original position to lock the

lead wires. Lightly pull the lead wires to confirm

a good connection.

3 Orient the AM loop

antenna so that the best

reception is obtained.

(U.S.A. model)

01RX-V595a-e/f2 6/24/99, 11:43 AM20

Страница загружается...

Yamaha HTR-6280, HTR-5150 Инструкция по применению

Похожие модели бренда

Модели других брендов