Sony MEX-BT2500 Инструкция по применению

Operating Instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

Инструкция по эксплуатации

MEX-BT2500

3-100-199-23 (1)

GB

DE

FR

IT

NL

©

2007 Sony Corporation

RU

To cancel the demonstration (DEMO) display, see page 16.

Zum Deaktivieren der Demo-Anzeige (DEMO) schlagen Sie bitte auf Seite 17 nach.

Pour annuler la démonstration (DEMO), reportez-vous à la page 17.

Per annullare la dimostrazione (DEMO), vedere pagina 17.

Om de demonstratie (DEMO) te annuleren, zie pagina 17.

Для отмены демонстрации на дисплее (режим Demo) см. стр. 18.

Bluetooth Audio System

Bluetooth™

Audio System

2

The nameplate indicating operating voltage, etc.,

is located on the bottom of the chassis.

Hereby, Sony Corp., declares that this MEX-

BT2500 is in compliance with the essential

requirements and other relevant provisions of

Directive 1999/5/EC.

For details, please access the following URL:

http://www.compliance.sony.de/

Be sure to install this unit in the dashboard of

the car for safety. For installation and

connections, see the supplied installation/

connections manual.

Warning if your car’s ignition has no

ACC position

Be sure to set the Auto Off function (page 16).

The unit will shut off completely and

automatically in the set time after the unit is

turned off, which prevents battery drain.

If you do not set the Auto Off function, press

and hold (OFF) until the display disappears

each time you turn the ignition off.

This label is located on the bottom of the

chassis.

Disposal of Old Electrical &

Electronic Equipment (Applicable in

the European Union and other

European countries with separate

collection systems)

This symbol on the product or on its

packaging indicates that this product shall not be treated

as household waste. Instead it shall be handed over to the

applicable collection point for the recycling of electrical

and electronic equipment. By ensuring this product is

disposed of correctly, you will help prevent potential

negative consequences for the environment and human

health, which could otherwise be caused by inappropriate

waste handling of this product. The recycling of materials

will help to conserve natural resources. For more detailed

information about recycling of this product, please contact

your local Civic Office, your household waste disposal

service or the shop where you purchased the product.

Applicable accessory: Remote commander

3

Table of Contents

Welcome ! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Getting Started

Resetting the unit. . . . . . . . . . . . . . . . . . . . . . . . 5

Preparing the card remote commander . . . . . . . 5

Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . 6

Adjusting the volume level of each device . . . . 6

Detaching the front panel . . . . . . . . . . . . . . . . . 6

Attaching the front panel . . . . . . . . . . . . . . . 7

Location of controls and basic

operations

Main unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Card remote commander RM-X304 . . . . . . . 8

CD

Display items . . . . . . . . . . . . . . . . . . . . . . . 10

Repeat and shuffle play. . . . . . . . . . . . . . . . 10

Radio

Storing and receiving stations . . . . . . . . . . . . . 10

Storing automatically — BTM . . . . . . . . . . 10

Storing manually. . . . . . . . . . . . . . . . . . . . . 10

Receiving the stored stations . . . . . . . . . . . 10

Tuning automatically . . . . . . . . . . . . . . . . . 10

RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Setting AF and TA . . . . . . . . . . . . . . . . . . . 11

Selecting PTY . . . . . . . . . . . . . . . . . . . . . . . 12

Setting CT. . . . . . . . . . . . . . . . . . . . . . . . . . 12

Bluetooth function

Bluetooth operations. . . . . . . . . . . . . . . . . . . . 13

Pairing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

About Bluetooth icons . . . . . . . . . . . . . . . . 14

Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

To switch the Bluetooth signal output of

this unit to on . . . . . . . . . . . . . . . . . . . . . . . 14

Connecting a cellular phone. . . . . . . . . . . . 14

Connecting an audio device . . . . . . . . . . . . 14

Handsfree talk. . . . . . . . . . . . . . . . . . . . . . . . . 14

Receiving calls . . . . . . . . . . . . . . . . . . . . . . 14

Making calls. . . . . . . . . . . . . . . . . . . . . . . . 15

Call transfer . . . . . . . . . . . . . . . . . . . . . . . . 15

Music streaming . . . . . . . . . . . . . . . . . . . . . . . 15

Listening to music from an audio

device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Operating an audio device with this

unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Deleting registration of all paired devices . . . 15

Other functions

Changing the sound settings . . . . . . . . . . . . . . 16

Adjusting the balance and fader

— BAL/FAD . . . . . . . . . . . . . . . . . . . . . . . 16

Customizing the equalizer curve

— EQ lite . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Adjusting setup items — SET . . . . . . . . . . . . 16

Using optional equipment. . . . . . . . . . . . . . . . 17

Auxiliary audio equipment. . . . . . . . . . . . . 17

Additional Information

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Notes on discs . . . . . . . . . . . . . . . . . . . . . . 18

About MP3/WMA files . . . . . . . . . . . . . . . 18

About Bluetooth function. . . . . . . . . . . . . . 19

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Removing the unit. . . . . . . . . . . . . . . . . . . . . . 20

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 21

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 22

Error displays/Messages. . . . . . . . . . . . . . . 23

4

Welcome !

Thank you for purchasing this Sony Bluetooth™

Audio System. You can enjoy your drive with the

following functions.

• CD playback

You can play CD-DA (also containing CD

TEXT*) and CD-R/CD-RW (MP3/WMA files

also containing Multi Session (page 18)).

• Radio reception

– You can store up to 6 stations per band (FM1,

FM2, FM3, MW and LW).

– BTM (Best Tuning Memory): the unit selects

strong signal stations and stores them.

• RDS services

– You can use FM station with Radio Data

System (RDS).

• Bluetooth function

– Handsfree talking with your cellular phone in

the car. This unit can answer and redial.

– Music streaming from your cellular phone or

portable audio device.

– HFP 1.0, HSP, A2DP and AVRCP profiles

supported.

• Sound adjustment

– EQ lite: You can choose any one of 6 preset

equalizer curves.

• Auxiliary equipment connection

An AUX input jack on the front of the unit

allows connection of a portable audio device.

* A CD TEXT disc is a CD-DA that includes

information such as disc, artist and track name.

The Bluetooth word mark and logos are owned

by the Bluetooth SIG, Inc. and any use of such

marks by Sony Corporation is under license.

Other trademarks and trade names are those of

their respective owners.

Caution

IN NO EVENT SHALL SONY BE LIABLE FOR

ANY INCIDENTAL, INDIRECT OR

CONSEQUENTIAL DAMAGES OR OTHER

DAMAGES INCLUDING, WITHOUT

LIMITATION, LOSS OF PROFITS, LOSS OF

REVENUE, LOSS OF DATA, LOSS OF USE OF

THE PRODUCT OR ANY ASSOCIATED

EQUIPMENT, DOWNTIME, AND

PURCHASER’S TIME RELATED TO OR

ARISING OUT OF THE USE OF THIS

PRODUCT, ITS HARDWARE AND/OR ITS

SOFTWARE.

IMPORTANT NOTICE!

Safe and efficient use

Changes or modifications to this unit not expressly

approved by Sony may void the user’s authority to

operate the equipment.

Please check for exceptions, due to national

requirement or limitations, in usage of Bluetooth

equipment before using this product.

Driving

Check the laws and regulations on the use of cellular

phones and handsfree equipment in the areas where

you drive.

Always give full attention to driving and pull off the

road and park before making or answering a call if

driving conditions so require.

Connecting to other devices

When connecting to any other device, please read its

user guide for detailed safety instructions.

Type of discs Label on the disc

CD-DA

MP3

WMA

Microsoft, Windows Media,

and the Windows logo are

trademarks or registered

trademarks of Microsoft

Corporation in the United States and/or other

countries.

5

Radio frequency exposure

RF signals may affect improperly installed or

inadequately shielded electronic systems in cars,

such as electronic fuel injection systems, electronic

antiskid (antilock) braking systems, electronic speed

control systems or air bag systems. For installation

or service of this device, please consult with the

manufacturer or its representative of your car. Faulty

installation or service may be dangerous and may

invalidate any warranty that may apply to this

device.

Consult with the manufacturer of your car to ensure

that the use of your cellular phone in the car will not

affect its electronic system.

Check regularly that all wireless device equipment

in your car is mounted and operating properly.

Emergency calls

This Bluetooth car handsfree and the electronic

device connected to the handsfree operate using

radio signals, cellular, and landline networks as well

as user-programmed function, which cannot

guarantee connection under all conditions.

Therefore do not rely solely upon any electronic

device for essential communications (such as

medical emergencies).

Remember, in order to make or receive calls, the

handsfree and the electronic device connected to the

handsfree must be switched on in a service area with

adequate cellular signal strength.

Emergency calls may not be possible on all cellular

phone networks or when certain network services

and/or phone features are in use.

Check with your local service provider.

Getting Started

Resetting the unit

Before operating the unit for the first time, or

after replacing the car battery or changing the

connections, you must reset the unit.

Detach the front panel and press the RESET

button with a pointed object, such as a ball-point

pen.

Note

Pressing the RESET button will erase the clock setting

and some stored contents.

Preparing the card remote

commander

Before using the card remote commander for the

first time, remove the insulation film.

RESET

button

6

Setting the clock

The clock uses a 24-hour digital indication.

1 Press and hold the select button.

The setup display appears.

2 Press the select button repeatedly

until “CLOCK-ADJ” appears.

3 Press (SEEK) +.

The hour indication flashes.

4 Rotate the select button to set the

hour and minute.

To move the digital indication, press (DSPL).

5 Press the select button.

The setup is complete and the clock starts.

To display the clock, press (DSPL). Press

(DSPL) again to return to the previous display.

With the card remote commander

In step 4, to set the hour and minute, press M or m.

Tip

You can set the clock automatically with the RDS

feature (page 12).

Adjusting the volume level of

each device

When connecting to a portable audio device via

Bluetooth connection or AUX input jack, we

recommend adjusting the volume level of the

connected device, or adjusting the volume level

for each connected device in the setup menu on

this unit. See “Adjusting the volume level”

(page 15) for Bluetooth device, and “Adjusting

the volume level” (page 17) for a device

connected to AUX.

Detaching the front panel

You can detach the front panel of this unit to

prevent theft.

Caution alarm

If you turn the ignition switch to the OFF

position without detaching the front panel, the

caution alarm will sound for a few seconds.

The alarm will only sound if the built-in

amplifier is used.

1 Press (OFF).

The unit is turned off.

2 Press , then pull it off towards you.

Notes

• Do not drop or put excessive pressure on the front

panel and display window.

• Do not subject the front panel to heat/high

temperature or moisture. Avoid leaving it in a parked

car or on a dashboard/rear tray.

7

Attaching the front panel

Engage part A of the front panel with part B of

the unit, as illustrated, and push the left side into

position until it clicks.

Note

Do not put anything on the inner surface of the front

panel.

B

A

8

Location of controls and basic operations

Main unit

Card remote commander

RM-X304

Refer to the pages listed for details. The

corresponding buttons on the card remote

commander control the same functions as those

on the unit.

A OFF button

To power off; stop the source.

B EQ (equalizer)/BLUETOOTH button

16

CD/Radio/Bluetooth audio:

To select an equalizer type (XPLOD,

NATURAL, HARD, UPBEAT, VOCAL,

CUSTOM or OFF).

Power off:

For Bluetooth signal on/off, pairing.

C Volume control dial/select/

(handsfree) button 14, 16

To adjust volume (rotate); select setup items

(press and rotate); receive/end a call (press).

D SOURCE button

To power on; change the source (Radio/CD/

AUX/Bluetooth audio/Bluetooth phone).

OFF

DSPL

SEEK SEEK

PAUSE

ALBMDIM REP SHUF

EQ

AUX

123456

MODE

SOURCE

PUSH SELECT

/

BLUETOOTH

AF

/

TA

PTY

1

9

2

qg qhqf

4 5 8673

MEX-BT2500

qdqsqaq;

RESET

qkqj

OFF

DSPL

SCRL

SEL

SOURCE

MODE

132

465

ATT

VOL

+

–

+

–

4

ws

qs

1

wf

ql

qd

wa

w;

wg

wd

9

E Disc slot

To insert the disc (label side up). Playback

starts automatically.

F Display window

G AUX input jack 17

To connect a portable audio device.

H Z (eject) button

To eject the disc.

I (front panel release) button 6

J PTY (Program Type) button 12

To select PTY in RDS.

K SEEK –/+ buttons

CD:

To skip tracks (press); skip tracks

continuously (press, then press again within

about 1 second and hold); reverse/fast-

forward a track (press and hold).

Radio:

To tune in stations automatically (press); find

a station manually (press and hold).

Bluetooth audio device*

1

:

To skip tracks (press).

L MODE button 10

To select the radio band (FM/MW/LW).

M DSPL (display)/DIM (dimmer) button

10, 11

To change display items (press); change the

display brightness (press and hold).

N Number buttons

CD:

(1)/(2): ALBM –/+*

2

To skip albums (press); skip albums

continuously (press and hold).

(3): REP 10

(4): SHUF 10

(6): PAUSE*

3

To pause playback. To cancel, press

again.

Radio:

To receive stored stations (press); store

stations (press and hold).

Bluetooth audio device*

1

:

(6): PAUSE

To pause playback. To cancel, press

again.

O AF (Alternative Frequencies)/TA

(Traffic Announcement) button 11

To set AF and TA in RDS.

P Receptor for the card remote

commander

Q RESET button (located behind the front

panel) 5

R Microphone 14

Note

Do not cover the microphone, the handsfree

function may not work properly.

The following buttons on the card remote

commander have also different buttons/functions

from the unit. Remove the insulation film before

use (page 5).

ql < (.)/, (>) buttons

The same as (SEEK) –/+ on the unit.

w; VOL (volume) +/– button

To adjust volume.

wa ATT (attenuate) button

To attenuate the sound. To cancel, press

again.

ws SEL (select)/ (handsfree) button

The same as the select button on the unit.

wd M (+)/m (–) buttons

To control CD, the same as (1)/(2)

(ALBM –/+) on the unit.

wf SCRL (scroll) button 10

To scroll the display item.

wg Number buttons

To receive stored stations (press); store

stations (press and hold).

*1 When a Bluetooth audio device (supports AVRCP

of Bluetooth technology) is connected. Depending

on the device, certain operations may not be

available.

*2 When an MP3/WMA is played.

*3 When playing back on this unit.

Note

If the unit is turned off and the display disappears, it

cannot be operated with the card remote commander

unless (SOURCE) on the unit is pressed, or a disc is

inserted to activate the unit first.

Tip

For details on how to replace the battery, see

“Replacing the lithium battery of the card remote

commander” on page 20.

10

CD

Display items

*1 Album number is displayed only when the album is

changed.

*2 When playing an MP3, ID3 tag is displayed, and

when playing a WMA, WMA tag is displayed.

To change display items, press (DSPL); scroll

display items, set “A.SCRL-ON” (page 16).

Tip

Displayed items will differ, depending on the disc type,

recorded format and settings. For details on MP3/

WMA, see page 18.

Repeat and shuffle play

1 During playback, press (3) (REP) or

(4) (SHUF) repeatedly until the

desired setting appears.

* When an MP3/WMA is played.

To return to normal play mode, select “ OFF”

or “SHUF OFF.”

Radio

Storing and receiving stations

Caution

When tuning in stations while driving, use Best

Tuning Memory (BTM) to prevent an accident.

Storing automatically — BTM

1 Press (SOURCE) repeatedly until

“TUNER” appears.

To change the band, press (MODE)

repeatedly. You can select from FM1, FM2,

FM3, MW or LW.

2 Press and hold the select button.

The setup display appears.

3 Press the select button repeatedly

until “BTM” appears.

4 Press (SEEK) +.

The unit stores stations in order of frequency

on the number buttons.

A beep sounds when the setting is stored.

Storing manually

1 While receiving the station that you

want to store, press and hold a

number button ((1) to (6)) until

“MEMORY” appears.

The number button indication appears in the

display.

Note

If you try to store another station on the same number

button, the previously stored station will be replaced.

Tip

When a RDS station is stored, the AF/TA setting is

also stored (page 11).

Receiving the stored stations

1 Select the band, then press a number

button ((1) to (6)).

Tuning automatically

1 Select the band, then press (SEEK) –/+

to search for the station.

Scanning stops when the unit receives a

station. Repeat this procedure until the

desired station is received.

Select To play

TRACK track repeatedly.

ALBUM* album repeatedly.

SHUF ALBUM* album in random order.

SHUF DISC disc in random order.

Track number/Elapsed playing time, Disc/

artist name, Album number*

1

, Album

name, Track name, Text information*

2

,

Clock

11

Tip

If you know the frequency of the station you want to

listen to, press and hold (SEEK) –/+ to locate the

approximate frequency, then press (SEEK) –/+

repeatedly to fine adjust to the desired frequency

(manual tuning).

RDS

Overview

FM stations with Radio Data System (RDS)

service send inaudible digital information along

with the regular radio program signal.

Display items

A Frequency*

1

(Program service name), Preset

number, Clock, RDS data

B TA/TP*

2

*1 While receiving the RDS station, “ *” is displayed

on the left of the frequency indication.

*2 “TA” flashes during traffic information. “TP” lights

up while such a station is received.

To change display items A, press (DSPL).

RDS services

This unit automatically provides RDS services as

follows:

Notes

• Depending on the country/region, not all RDS

functions may be available.

• RDS will not work if the signal strength is too weak,

or if the station you are tuned to is not transmitting

RDS data.

Setting AF and TA

1 Press (AF/TA) repeatedly until the

desired setting appears.

Storing RDS stations with the AF and

TA setting

You can preset RDS stations along with the AF/

TA setting. If you use the BTM function, only

RDS stations are stored with the same AF/TA

setting.

If you preset manually, you can preset both RDS

and non-RDS stations with the AF/TA setting for

each.

1 Set AF/TA, then store the station with BTM or

manually.

Presetting the volume of traffic

announcements

You can preset the volume level of the traffic

announcements so as to not miss hearing them.

1 Rotate the volume control dial to adjust the

volume level.

2 Press and hold (AF/TA) until “TA” appears.

Receiving emergency

announcements

With AF or TA on, the emergency

announcements will automatically interrupt the

currently selected source.

AF (Alternative Frequencies)

Selects and retunes the station with the

strongest signal in a network. By using this

function, you can continuously listen to the

same program during a long-distance drive

without having to retune the same station

manually.

TA (Traffic Announcement)/TP (Traffic

Program)

Provides current traffic information/programs.

Any information/program received, will

interrupt the currently selected source.

PTY (Program Types)

Displays the currently received program type.

Also searches your selected program type.

CT (Clock Time)

The CT data from the RDS transmission sets

the clock.

BA

Select To

AF-ON activate AF and deactivate TA.

TA-ON activate TA and deactivate AF.

AF, TA-ON activate both AF and TA.

AF, TA-OFF deactivate both AF and TA.

continue to next page t

12

Staying with one regional program

— REG

When the AF function is on: this unit’s factory

setting restricts reception to a specific region, so

you will not be switched to another regional

station with a stronger frequency.

If you leave this regional program’s reception

area, set “REG-OFF” in setup during FM

reception (page 17).

Note

This function does not work in the UK and in some

other areas.

Local Link function (UK only)

This function enables you to select other local

stations in the area, even if they are not stored on

your number buttons.

1 During FM reception, press a number button

((1) to (6)) on which a local station is stored.

2 Within 5 seconds, press again a number button

of the local station.

Repeat this procedure until the local station is

received.

Selecting PTY

1 Press (PTY) during FM reception.

The current program type name appears if the

station is transmitting PTY data.

2 Press (PTY) repeatedly until the

desired program type appears.

3 Press (SEEK) –/+.

The unit starts to search for a station

broadcasting the selected program type.

Type of programs

Note

You cannot use this function in countries/regions

where no PTY data is available.

Setting CT

1 Set “CT-ON” in setup (page 16).

Notes

• The CT function may not work even though an RDS

station is being received.

• There might be a difference between the time set by

the CT function and the actual time.

NEWS (News), AFFAIRS (Current Affairs),

INFO (Information), SPORT (Sports),

EDUCATE (Education), DRAMA (Drama),

CULTURE (Culture), SCIENCE (Science),

VARIED (Varied), POP M (Popular Music),

ROCK M (Rock Music), EASY M (Easy

Listening), LIGHT M (Light Classical),

CLASSICS (Classical), OTHER M (Other

Music Type), WEATHER (Weather),

FINANCE (Finance), CHILDREN (Children’s

Programs), SOCIAL A (Social Affairs),

RELIGION (Religion), PHONE IN (Phone In),

TRAVEL (Travel), LEISURE (Leisure), JAZZ

(Jazz Music), COUNTRY (Country Music),

NATION M (National Music), OLDIES (Oldies

Music), FOLK M (Folk Music), DOCUMENT

(Documentary)

13

Bluetooth function

Bluetooth operations

To use the Bluetooth function, the following

procedure is necessary.

1 Pairing:

When connecting Bluetooth devices for the

first time, mutual registration is required. This

is called “pairing.” This registration (pairing)

is required only for the first time, as this unit

and the other devices will recognize each

other automatically from the next time. You

can pair up to 8 devices. (Depending on the

device, you may need to input a passcode for

each connection.)

2 Connection

Sometimes pairing allows to connect

automatically. To use the device after pairing

is made, start the connection.

3 Handsfree talk/Music streaming

You can call a cellular phone and listen to

music when the connection is made.

Pairing

First, register (“pair”) a Bluetooth device

(cellular phone, etc.) and this unit with each

other. You can pair up to 8 devices. Once pairing

is established, there is no need for pairing again.

1 Press (OFF).

Be sure the clock or the demonstration

appears.

The Auto off function is set, if the unit is

turned off and the display disappears, press

and hold (OFF) to set the power on.

2 Place the Bluetooth device within 1 m

(3 ft) of this unit.

3 Press and hold (EQ/BLUETOOTH) until

“ ” flashes (about 7 seconds).

The unit enters pairing standby mode.

4 Set the Bluetooth device to search for

this unit.

A list of detected devices appears in the

display of the connecting device. This unit is

displayed as “XPLOD” on the connecting

device.

5 If Passcode* input is required on the

display of a connecting device, input

“0000.”

This unit and the Bluetooth device memorize

each other’s information, and when pairing is

made, the unit is ready for connection to the

device.

“ ” flashes and then stays lit after pairing is

complete.

6 Set the Bluetooth device to connect to

this unit.

“ ” or “ ” appears when the connection is

made.

* Passcode may be called “passkey,” “PIN code,” “PIN

number” or “Password,” etc., depending on the

device.

Note

Pairing standby mode is not released until the

connection is made.

flashing

XXXXXXX

DR-BT30Q

XPLOD

XXXX

Input passcode.

“0000”

14

About Bluetooth icons

The following icons are used by this unit.

Connection

If pairing has already been achieved, start

operation from here.

To switch the Bluetooth signal

output of this unit to on

To use the Bluetooth function, switch the

Bluetooth signal output of this unit to on.

1 While the unit is turned off, press and

hold (EQ/BLUETOOTH) until “ ” lights

(about 3 seconds).

Bluetooth signal is switched to on.

Connecting a cellular phone

1 Be sure that both this unit and a

cellular phone are switched to

Bluetooth signal on.

2 Connect to this unit using your

cellular phone.

“ ”appears when the connection is made.

Connecting the last-connected

cellular phone from this unit

1 Be sure that both this unit and the cellular

phone are switched to Bluetooth signal on.

2 Press (SOURCE) repeatedly until “BT

PHONE” appears.

3 Press (handsfree).

“ ” flashes while the connection is being

made. And then “ ” stays lit when the

connection is made.

Note

While streaming Bluetooth audio, you cannot connect

from this unit to the cellular phone. Connect from the

cellular phone to this unit instead. A connecting noise

may be heard over playback sound.

Tip

With Bluetooth signal on: when the ignition is switched

to on, this unit reconnects automatically to the last-

connected cellular phone. But automatic connection

also depends on the cellular phone’s specification. If

this unit does not reconnect automatically, connect

manually.

Connecting an audio device

1 Be sure that both this unit and the

audio device are switched to

Bluetooth signal on.

2 Connect to this unit using the audio

device.

“ ” appears when the connection is made.

Connecting the last-connected audio

device from this unit

1 Be sure that both this unit and the audio device

are switched to Bluetooth signal on.

2 Press (SOURCE) repeatedly until “BT

AUDIO” appears.

3 Press (6).

“ ” flashes while the connection is being

made. And then “ ” stays lit when the

connection is made.

Handsfree talk

Receiving calls

When receiving a call, a ring tone is output from

your car speakers. Check that the unit and

cellular phone are connected beforehand.

1 Press (handsfree) when a call is

received with a ring tone.

The phone call starts.

To end a call

Press (handsfree) again.

To reject an incoming call, press and hold

(handsfree) for 2 seconds.

Note

The microphone of this unit is located on the rear of

the front panel (page 9). Do not cover the microphone

with tape, etc.

lit:

flashing:

off:

Bluetooth signal on

Pairing standby mode

Bluetooth signal off

lit:

flashing:

off:

Connection successful

Connecting

No connection

lit:

flashing:

off:

Connection successful

Connecting

No connection

15

Making calls

In the case of making calls from this unit, only

redial is used.

1 Press (SOURCE) repeatedly until “BT

PHONE” appears.

2 Press and hold (handsfree) for 3

seconds or more.

The phone call starts.

To end a call

Press (handsfree) again.

To call another phone, use your cellular phone,

and then transfer the call.

For call transfer details, check the following.

Call transfer

In order to activate/deactivate the appropriate

device (this unit/cellular phone), check the

following.

1 Press and hold (handsfree) or use

your cellular phone.

For details on cellular phone operation, refer to

your cellular phone manual.

Note

Depending on the cellular phone, handsfree

connection may be cut off when call transfer is

attempted.

Music streaming

Listening to music from an audio

device

You can listen to music of an audio device on this

unit if the audio device supports A2DP

(Advanced Audio Distribution Profile) of

Bluetooth technology.

1 Turn down the volume on this unit.

2 Press (SOURCE) repeatedly until “BT

AUDIO” appears.

3 Operate the audio device to start

playback.

4 Adjust the volume on this unit.

Adjusting the volume level

The volume level is adjustable for any difference

between the unit and the Bluetooth audio device.

1 Start playback of the Bluetooth audio device at

a moderate volume.

2 Set your usual listening volume on the unit.

3 Press the select button repeatedly until “BT

AU” appears, and rotate the volume control

dial to adjust the input level (–8 dB to +18

dB).

Operating an audio device with this

unit

You can perform the following operations on this

unit if the audio device supports AVRCP (Audio

Video Remote Control Profile) of Bluetooth

technology. (The operation differs depending on

the audio device.)

* Depending on the device, it may be necessary to

press twice.

Operations other than the above should be

performed on the audio device.

Note

Even if the source is changed on this unit, playback of

the audio device does not stop.

Tip

You can connect a cellular phone that supports A2DP

(Advanced Audio Distribution Profile) as an audio

device and listen to music.

Deleting registration of all

paired devices

1 Press (OFF).

This unit is turned off.

2 If “ ” lights, press and hold

(EQ/ BLUETOOTH) until “ ” turns off.

3 Press and hold the select button.

4 Press the select button repeatedly

until “BT INIT” appears.

5 Press (SEEK) +.

Initializing starts.

It takes 8 seconds to cancel all registration.

Do not turn off the power while “INITIAL” is

flashing.

To Press

Play (6) (PAUSE) on this unit.

Pause (6) (PAUSE)* on this unit.

Skip tracks SEEK –/+ (

./>) [once for

each track]

16

Other functions

Changing the sound settings

Adjusting the balance and fader

— BAL/FAD

1 Press the select button repeatedly

until “BAL” or “FAD” appears.

The item changes as follows:

LOW*

1

t HI*

1

t BAL (left-right) t

FAD (front-rear) t AUX*

2

t BT AU*

3

*1 When EQ lite is activated (page 16).

*2 When AUX source is activated (page 17).

*3 When Bluetooth audio source is activated.

(page 15)

2 Rotate the select button to adjust the

selected item.

After 3 seconds, the setting is complete and

the display returns to normal play/reception

mode.

With the card remote commander

In step 2, to adjust the selected item, press <, M , ,

or m.

Customizing the equalizer curve

— EQ lite

“CUSTOM” of EQ lite allows you to make your

own equalizer settings.

1 Select a source, then press (EQ)

repeatedly to select “CUSTOM.”

2 Press the select button repeatedly

until “LOW” or “HI” appears.

3 Rotate the select button to adjust the

selected item.

The volume level is adjustable in 1 dB steps,

from –10 dB to +10 dB.

Repeat steps 2 and 3 to adjust the equalizer

curve.

To restore the factory-set equalizer curve,

press and hold the select button before the

setting is complete.

After 3 seconds, the setting is complete and

the display returns to normal play/reception

mode.

Tip

Other equalizer types are also adjustable.

With the card remote commander

In step 3, to adjust the selected item, press <, M , ,

or m.

Adjusting setup items — SET

1 Press and hold the select button.

The setup display appears.

2 Press the select button repeatedly

until the desired item appears.

3 Rotate the select button to select the

setting (example “ON” or “OFF”).

4 Press and hold the select button.

The setup is complete and the display returns

to normal play/reception mode.

Note

Displayed items will differ, depending on the source

and setting.

With the card remote commander

In step 3, to select the setting, press < or ,.

The following items can be set (follow the page

reference for details):

“

z” indicates the default settings.

CLOCK-ADJ (Clock Adjust) (page 6)

CT (Clock Time)

To set “CT-ON” or “CT-OFF” (z) (page 11, 12).

BEEP

To set “BEEP-ON” (z) or “BEEP-OFF.”

AUX-A*

1

(AUX Audio)

To turn the AUX source display “AUX-A-ON”

(

z) or “AUX-A-OFF” (page 17).

A.OFF (Auto Off)

To shut off automatically after a desired time

when the unit is turned off: “A.OFF-NO” (

z),

“A.OFF-30S (Seconds),” “A.OFF-30M

(Minutes)” or “A.OFF-60M (Minutes).”

DEMO*

1

(Demonstration)

To set “DEMO-ON” (z) or “DEMO-OFF.”

DIM (Dimmer)

To change the brightness of the display.

– “DIM-ON”: to dim the display.

–“DIM-OFF” (

z): to deactivate the dimmer.

A.SCRL (Auto Scroll)

To scroll long displayed item automatically

when the album/track is changed.

– “A.SCRL-ON” (

z): to scroll.

– “A.SCRL-OFF”: to not scroll.

LOCAL (Local Seek Mode)

– “LOCAL-ON” : to only tune into stations with

stronger signals.

–“LOCAL-OFF” (

z): to tune normal reception.

17

Using optional equipment

Auxiliary audio equipment

By connecting an optional portable audio device

to the AUX input jack (stereo mini jack) on the

unit and then simply selecting the source, you

can listen on your car speakers. The volume level

is adjustable for any difference between the unit

and the portable audio device. Follow the

procedure below:

Connecting the portable audio

device

1 Turn off the portable audio device.

2 Turn down the volume on the unit.

3 Connect to the unit.

* Be sure to use a straight type plug.

Adjusting the volume level

Be sure to adjust the volume for each connected

audio device before playback.

1 Turn down the volume on the unit.

2 Press (SOURCE) repeatedly until “AUX”

appears.

“FRONT IN” appears.

3 Start playback of the portable audio device at a

moderate volume.

4 Set your usual listening volume on the unit.

5 Press the select button repeatedly until “AUX”

appears, and rotate the volume control dial to

adjust the input level (–8 dB to +18 dB).

MONO (Monaural Mode)*

2

To improve poor FM reception, select monaural

reception mode.

– “MONO-ON” : to hear stereo broadcast in

monaural.

– “MONO-OFF” (

z): to hear stereo broadcast in

stereo.

REG*

2

(Regional)

To set “REG-ON” (

z) or “REG-OFF” (page 12).

LOUD (Loudness)

To allow you to listen clearly at low volume

levels.

– “LOUD -ON” : to reinforce bass and treble.

– “LOUD -OFF” (

z) : to not reinforce bass and

treble.

BTM (page 10)

BT INIT*

1

(page 15)

*1 When the unit is turned off.

*2 When FM is received.

AUX

Connecting cord*

(not supplied)

18

Additional Information

Precautions

• If your car has been parked in direct sunlight,

allow the unit to cool off before operating it.

• Power antenna (aerial) will extend automatically

while the unit is operating.

Moisture condensation

On a rainy day or in a very damp area, moisture

condensation may occur inside the lenses and

display of the unit. Should this occur, the unit will

not operate properly. In such a case, remove the disc

and wait for about an hour until the moisture has

evaporated.

To maintain high sound quality

Be careful not to splash juice or other soft drinks

onto the unit or discs.

Notes on discs

• To keep a disc clean, do not touch its surface.

Handle the disc by its edge.

• Keep your discs in their cases or disc magazines

when not in use.

• Do not subject discs to heat/high temperature.

Avoid leaving them in a parked car or on a

dashboard/rear tray.

• Do not attach labels, or use discs with sticky ink/

residue. Such discs may stop spinning when used,

causing a malfunction, or may ruin the disc.

• Do not use any discs with labels or stickers

attached.

The following malfunctions may result from using

such discs:

– Inability to eject a disc (due to a label or sticker

peeling off and jamming the eject mechanism).

– Inability to read audio data correctly (e.g.,

playback skipping, or no playback) due to heat

shrinking of a sticker or label causing a disc to

warp.

• Discs with non-standard shapes (e.g., heart,

square, star) cannot be played on this unit.

Attempting to do so may damage the unit. Do not

use such discs.

• You cannot play 8 cm (3

1

/4 in) CDs.

• Before playing, clean the discs

with a commercially available

cleaning cloth. Wipe each disc

from the center out. Do not use

solvents such as benzine,

thinner, commercially available

cleaners, or antistatic spray

intended for analog discs.

Notes on CD-R/CD-RW discs

• Some CD-Rs/CD-RWs (depending on the

equipment used for its recording or the condition

of the disc) may not play on this unit.

• You cannot play a CD-R/a CD-RW that is not

finalized.

Music discs encoded with copyright

protection technologies

This product is designed to play back discs that

conform to the Compact Disc (CD) standard.

Recently, various music discs encoded with

copyright protection technologies are marketed by

some record companies. Please be aware that among

those discs, there are some that do not conform to

the CD standard and may not be playable by this

product.

About MP3/WMA files

MP3, which stands for MPEG-1 Audio Layer-3, is a

music file compression format standard. It

compresses audio CD data to approximately 1/10 of

its original size.

WMA, which stands for Windows Media Audio, is

another music file compression format standard. It

compresses audio CD data to approximately 1/22*

of its original size.

* only for 64 kbps

• The unit is compatible with the ISO 9660 level 1/

level 2 format, Joliet/Romeo in the expansion

format, and Multi Session.

• The maximum number of:

– folders (albums): 150 (including root and empty

folders).

– MP3/WMA files (tracks) and folders contained

in a disc: 300 (if a folder/file names contain

many characters, this number may become less

than 300).

– displayable characters for a folder/file name is

32 (Joliet), or 64 (Romeo).

• ID3 tag versions 1.0, 1.1, 2.2, 2.3 and 2.4 apply to

MP3 only. ID3 tag is 15/30 characters (1.0 and

1.1), or 63/126 characters (2.2, 2.3 and 2.4).

WMA tag is 63 characters.

Note on DualDiscs

A DualDisc is a two sided disc product which

mates DVD recorded material on one side with

digital audio material on the other side. However,

since the audio material side does not conform to

the Compact Disc (CD) standard, playback on this

product is not guaranteed.

19

Playback order of MP3/WMA files

Notes

• When naming an MP3 file/WMA file, be sure to add

the file extension “.mp3”/“.wma” to the file name.

• During playback of a VBR (variable bit rate) MP3/

WMA file or fast-forward/reverse, elapsed playing

time may not display accurately.

• When the disc is recorded in Multi Session, only the

first track of the first session format is recognized

and played (any other format is skipped). The

priority of the format is CD-DA and MP3/WMA.

– When the first track is a CD-DA, only CD-DA of the

first session is played.

– When the first track is not a CD-DA, an MP3/WMA

session is played. If the disc has no data in any of

these formats, “NO MUSIC” is displayed.

Notes on MP3

• Be sure to finalize the disc before using on the unit.

• If you play a high-bit-rate MP3, such as 320 kbps,

sound may be intermittent.

Notes on WMA

• Files made with lossless compression are not

playable.

• Files protected by copyright are not playable.

About Bluetooth function

What is Bluetooth technology?

• Bluetooth wireless technology is a short-range

wireless technology that enables wireless data

communication between digital devices, such as a

cellular phone and a headset. Bluetooth wireless

technology operates within a range of about 10 m

(about 33 feet). Connecting two devices is

common, but some devices can be connected to

multiple devices at the same time.

• You do not need to use a cable for connection

since Bluetooth technology is a wireless

technology, neither is it necessary for the devices

to face one another, such is the case with infrared

technology. For example, you can use such a

device in a bag or pocket.

• Bluetooth technology is an international standard

supported by millions of companies all over the

world, and employed by various companies

worldwide.

On Bluetooth communication

• Bluetooth wireless technology operates within a

range of about 10 m.

Maximum communication range may vary

depending on obstacles (person, metal, wall, etc.)

or electromagnetic environment.

• The following conditions may affect the

sensitivity of Bluetooth communication.

– There is an obstacle such as a person, metal, or

wall between this unit and Bluetooth device.

– A device using 2.4 GHz frequency, such as a

wireless LAN device, cordless telephone, or

microwave oven, is in use near this unit.

• Because Bluetooth devices and wireless LAN

(IEEE802.11b/g) use the same frequency,

microwave interference may occur and resulting in

communication speed deterioration, noise, or

invalid connection if this unit is used near a

wireless LAN device. In such as case, perform the

following.

– Use this unit at least 10 m away from the

wireless LAN device.

– If this unit is used within 10 m of a wireless

LAN device, turn off the wireless LAN device.

– Install this unit and Bluetooth device as near to

each other as possible.

• Microwaves emitting from a Bluetooth device may

affect the operation of electronic medical devices.

Turn off this unit and other Bluetooth devices in

the following locations, as it may cause an

accident.

– where inflammable gas is present, in a hospital,

train, airplane, or a petrol station

– near automatic doors or a fire alarm

• This unit supports security capabilities that

comply with the Bluetooth standard to provide a

secure connection when the Bluetooth wireless

technology is used, but security may not be

enough depending on the setting. Be careful when

communicating using Bluetooth wireless

technology.

• We do not take any responsibility for the leakage

of information during Bluetooth communication.

• Connection with all Bluetooth devices cannot be

guaranteed.

– A device featuring Bluetooth function is

required to conform to the Bluetooth standard

specified by Bluetooth SIG, and be

authenticated.

– Even if the connected device conforms to the

above mentioned Bluetooth standard, some

devices may not be connected or work correctly,

depending on the features or specifications of the

device.

– While talking on the phone hands free, noise

may occur, depending on the device or

communication environment.

• Depending on the device to be connected, it may

require some time to start communication.

Folder

(album)

MP3/WMA file

(track)

MP3/WMA

continue to next page t

20

Others

• Using the Bluetooth device may not function on

cellular phones, depending on radio wave

conditions and location where the equipment is

being used.

• If you experience discomfort after using the

Bluetooth device, stop using the Bluetooth device

immediately. Should any problem persist, consult

your nearest Sony dealer.

If you have any questions or problems concerning

your unit that are not covered in this manual, consult

your nearest Sony dealer.

Maintenance

Replacing the lithium battery of the

card remote commander

Under normal conditions, the battery will last

approximately 1 year. (The service life may be

shorter, depending on the conditions of use.)

When the battery becomes weak, the range of the

card remote commander becomes shorter.

Replace the battery with a new CR2025 lithium

battery. Use of any other battery may present a

risk of fire or explosion.

Notes on the lithium battery

• Keep the lithium battery out of the reach of children.

Should the battery be swallowed, immediately

consult a doctor.

• Wipe the battery with a dry cloth to assure a good

contact.

• Be sure to observe the correct polarity when

installing the battery.

• Do not hold the battery with metallic tweezers,

otherwise a short-circuit may occur.

Fuse replacement

When replacing the fuse, be

sure to use one matching the

amperage rating stated on the

original fuse. If the fuse blows,

check the power connection and

replace the fuse. If the fuse

blows again after replacement,

there may be an internal

malfunction. In such a case,

consult your nearest Sony

dealer.

Cleaning the connectors

The unit may not function properly if the connectors

between the unit and the front panel are not clean. In

order to prevent this, detach the front panel (page 6)

and clean the connectors with a cotton swab. Do not

apply too much force. Otherwise, the connectors

may be damaged.

Notes

• For safety, turn off the ignition before cleaning the

connectors, and remove the key from the ignition

switch.

• Never touch the connectors directly with your fingers

or with any metal device.

Removing the unit

1 Remove the protection collar.

1Detach the front panel (page 6).

2Engage the release keys together with the

protection collar.

1

2

+ side up

c

WARNING

Battery may explode if mistreated.

Do not recharge, disassemble, or dispose of

in fire.

Fuse (10A)

Main unit Back of the front

panel

Orient the release

keys as shown.

Страница загружается ...

Sony MEX-BT2500 Инструкция по применению

Sony MEX-BT2500 Инструкция по применению

на других языках

Похожие модели бренда

Модели других брендов