Hilti NUN 054 IE-A22 Руководство пользователя

NUN 054 IE-A22

English 1

Русский 12

日本語 25

한국어 36

繁體中文 47

中文 56

1

2

3

4

5

6

7

8

NUN 054 IE-A22

en Originaloperatinginstructions....................................... 1

ru Перевод оригинального руководства по эксплуатации . . . . . . . . . . . . . . . . . . . . 12

ja オリジナル取扱説明書 ............................................ 25

ko 오리지널사용설명서............................................. 36

zh 原廠操作說明.................................................. 47

cn 原版操作说明译文 ............................................... 56

*2207121* 2207121 English 1

Original operating instructions

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free

handling and use of the product.

• Observe the safety instructions and warnings in this documentation and on the product.

• Always keep the operating instructions with the product and make sure that the operating instructions

are with the product when it is given to other persons.

1.2 Explanation of symbols

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the

equipment or other property.

1.2.2 Symbols in the operating instructions

The following symbols are used in these operating instructions:

Comply with the operating instructions

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

Hilti Liion battery

Hilti charger

1.2.3 Symbols in illustrations

The following symbols are used in illustrations:

These numbers refer to the illustrations at the beginning of these operating instructions.

The numbering reflects the sequence of operations shown in the illustrations and may deviate

from the steps described in the text.

Item reference numbers are used in the overview illustration and refer to the numbers used in

the key in the product overview section.

These characters are intended to specifically draw your attention to certain points when handling

the product.

2 English 2207121 *2207121*

1.3 Symbols on the power tool

1.3.1 Symbols

The following symbols are used:

Risk of crushing injury!

Risk of cutting injury!

Wear protective glasses!

The power tool supports near-field communication (NFC) technology, which is compatible with

iOS and Android platforms.

Direct current (DC)

Li-ion battery

Hilti Li-ion battery type series used. Observe the information given in the section headed

Intended use.

Never use the battery as a striking tool.

Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any

other way.

If applied on the product, the product has been certified by this certification body for the US and

Canadian markets according to the applicable standards.

1.4 Product information

products are designed for professional users and only trained, authorized personnel are

permitted to operate, service and maintain the products. This personnel must be specifically informed about

the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by

untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are printed on the rating plate.

▶Write down the serial number in the table below. You will be required to state the product details when

contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Crimping / pressing and cutting tool NUN 054 IE-A22

Generation 01

Serial no.

1.5 Declaration of conformity

The manufacturer declares, on his sole responsibility, that the product described here complies with the

applicable legislation and standards. A copy of the declaration of conformity can be found at the end of this

documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D-86916 Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

*2207121* 2207121 English 3

Work area safety

▶Keep work area clean and well lit. Cluttered or dark areas invite accidents.

▶Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

▶Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

Electrical safety

▶Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

▶Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

▶Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

▶Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

▶When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

▶If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

▶Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

▶Use personal protective equipment. Always wear eye protection. Protective equipment such as a

dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will

reduce personal injuries.

▶Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on

the switch or energising power tools that have the switch on invites accidents.

▶Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

▶Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

▶Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

▶If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used. Use of dust collection can reduce dust-related hazards.

▶Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

▶Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

▶Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

▶Disconnect the plug from the power source and/or remove the battery pack, if detachable, from

the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

▶Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

▶Maintain power tools and accessories. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

▶Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

4 English 2207121 *2207121*

▶Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

▶Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

▶Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with another battery pack.

▶Use power tools only with specifically designated battery packs. Use of any other battery packs may

create a risk of injury and fire.

▶When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a fire.

▶Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

▶Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may

exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

▶Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature

above 130° C (265 °F) may cause explosion.

▶Follow all charging instructions and do not charge the battery pack or tool outside the temperature

range specified in the instructions. Charging improperly or at temperatures outside the specified range

may damage the battery and increase the risk of fire.

Service

▶Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

▶Never service damaged battery packs. Service of battery packs should only be performed by the

manufacturer or authorized service providers.

2.2 Additional safety instructions for crimping and cutting tools

Personal safety

▶Use the product only if it is in perfect working order.

▶Never tamper with or modify the tool in any way.

▶Check that the locking pin is pushed in all the way and securely engaged.

Electrical safety

▶Before use of the power tool, all live cables or other items carrying electric voltage within the area in which

the user is working are to be switched off. If this is not possible, the corresponding safety precautions

for working in proximity to live cables or equipment must be implemented and observed.

▶Do not crimp or cut through live cables, i.e. cables carrying electricity. The tool must be considered to

be uninsulated and must therefore be used in conjunction with personal protective equipment (protective

gloves, protective footwear, protective clothing, etc.) of a type suitable to provide protection for yourself

and other persons in the vicinity. The power tool is suitable for use on insulated platforms.

Power tool use and care

▶After approx. 50 consecutive crimping or cutting operations, switch the power tool off and allow it to

cool down for about 15 minutes. Overheating can lead to damage to the power tool.

▶Risk of injury by falling tools and/or accessories. Before starting work, check that installed accessories

are secure.

2.3 Careful handling and use of batteries

▶Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.

▶Do not expose batteries to high temperatures, direct sunlight or fire.

▶Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C

(176 °F).

▶Do not use or charge batteries that have suffered mechanical impact, have been dropped from a height

or show signs of damage. In this case, always contact your Hilti Service.

▶If the battery is too hot to touch it may be defective. Put the battery in a place where it is clearly visible

and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to

cool down. If it is still too hot to touch after an hour, the battery is faulty. Contact Hilti Service.

*2207121* 2207121 English 5

3 Description

3.1 Product overview 1

@Top section

;Manual piston return switch

=Casing

%Servicing and fault indicator (red LED)

&Battery release button

(Battery

)Slot on both sides, for attaching the Hilti re-

taining strap

+White LED to illuminate the working area

§Control switch

/Locking pin for opening/closing the tool head

:Pressing / cutting jaws

∙Catch

For securing and for removing the crimping /

pressing die

$Crimping / pressing die

Use with the corresponding crimping / press-

ing jaws, depending on the application.

3.2 Intended use

The product described is a cordless electro-hydraulic crimping and cutting tool.

It is designed for crimping connectors made of copper (Cu) or aluminum (Al) as well as for cutting through

electric cables made of copper (Cu), aluminum (Al) or steel.

Depending on the application it is to be used for, the tool can be equipped with crimping or cutting jaws.

Before use of the power tool, all live cables or other items carrying electric voltage within the area in which

the user is working must be switched off. If this is not possible, the corresponding safety precautions for

working in the proximity of live cables or equipment must be implemented and observed.

• Use only Hilti lithiumion batteries of the B 22 series with this product.

• Use only Hilti-approved battery chargers to charge these batteries. More information is available from

your Hilti Store or from www.hilti.group

3.3 Possible misuse

• Do not use this hand-held power tool clamped in a fixed position or as a stationary device.

• This electro-hydraulic crimping and cutting tool may not be exposed to heavy rain or used under water.

3.4 Lithiumion battery status display

The charge status of the Li-ion battery and malfunctions of the power tool are indicated by the display on

the Liion battery. The charge status of the Liion battery is displayed after pressing one of the two battery

release buttons.

Status Meaning

4 LEDs light. Charge status: 75 % to 100 %

3 LEDs light. Charge status: 50 % to 75 %

2 LEDs light. Charge status: 25 % to 50 %

1 LED lights. Charge status: 10 % to 25 %

1 LED blinks. Charge status: < 10 %

Battery charge status cannot be displayed while the control switch is pressed and for up to 5 seconds

after releasing the control switch. If the battery display LEDs blink, please observe the instructions

given in the Troubleshooting section.

6 English 2207121 *2207121*

3.5 Items supplied

Crimping / pressing and cutting tool, operating instructions.

Other system products approved for use with this product can be found at your local Hilti Store or at:

www.hilti.group

3.6 Selecting the crimping / pressing die

A table to assist with selecting the type of crimping / pressing die to be used can be found at the end of

these operating instructions.

4 Technical data

NUN 054 IE-A22

Rated voltage 21.6 V

Weight in accordance with EPTA Procedure 01 including B22⁄8.0 battery 2.6 kg

Crimping time ≈4s

Max. crimping / pressing force 53 kN

max. cutting capacity (outside diameter) (NCT J

CUAL cutting jaws)

Cu cable 33 mm

Al cable 33 mm

max. cutting capacity (outside diameter) (NCT J

ACSR cutting jaws)

Steel-reinforced Al ca-

ble

20.5 mm

Steel rope / guy wire

(EHS)

7 mm

Max. permissible crimping capacity Cu/Al standard con-

nector

240 mm²

Cu/Al fine-wire stan-

dard connector

185 mm²

Storage temperature −20 ℃ … 70 ℃

Ambient temperature for operation −17 ℃ … 60 ℃

4.1 Noise and vibration values in accordance with EN 60745

The sound pressure and vibration values given in these instructions were measured in accordance with a

standardized test and can be used to compare one power tool with another. They can also be used for a

preliminary assessment of exposure. The data given represents the main applications of the power tool.

However, if the power tool is used for different applications, with different accessory tools, or is poorly

maintained, the data can vary. This can significantly increase exposure over the total working period. An

accurate estimation of exposure should also take into account the times when the power tool is switched

off, or when it is running but not actually being used for a job. This can significantly reduce exposure over

the total working period. Identify additional safety measures to protect the operator from the effects of noise

and/or vibration, for example: maintaining the power tool and accessory tools, keeping the hands warm,

organization of work patterns.

Noise values

Sound (power) level (L WA)80 dB(A)

Uncertainty for the sound power level (K WA)2.5 dB(A)

Emission sound pressure level (L pA)70 dB(A)

Uncertainty for the sound pressure level (K pA)2.5 dB(A)

Vibration values

Total vibration (during operation) (a) 2.5 m/s²

Uncertainty (K) 1.5 m/s²

*2207121* 2207121 English 7

4.2 Battery

Battery operating voltage 21.6 V

Ambient temperature for operation −17 ℃ … 60 ℃

Storage temperature −20 ℃ … 40 ℃

Battery charging starting temperature −10 ℃ … 45 ℃

5 Operation

5.1 Preparations at the workplace

WARNING

Risk of injury by inadvertent starting!

▶Before inserting the battery, make sure that the product is switched off.

▶Remove the battery before making any adjustments to the power tool or before changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

5.2 Charging the battery

1. Before charging the battery, read the operating instructions for the charger.

2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.

3. Use an approved charger to charge the battery. → page 5

5.3 Inserting the battery

WARNING

Risk of injury by short circuit or falling battery!

▶Before inserting the battery, make sure that the contacts on the battery and the contacts on the product

are free of foreign matter.

▶Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.

2. Push the battery into the product until it engages with an audible click.

3. Check that the battery is seated securely.

5.4 Removing the battery

1. Press the battery release buttons.

2. Remove the battery from the tool.

5.5 Fitting the crimping / pressing or cutting jaws 2

WARNING

Risk of injury! Unintentional starting.

▶Remove the battery before fitting, changing or removing the crimping /pressing or cutting jaws.

Never operate the crimping / pressing tool without crimping / pressing or cutting jaws in place.

1. Remove the battery and select the most suitable crimping / pressing or cutting jaws.

2. Press the locking pins.

3. Rotate the locking pins counterclockwise as far as they will go.

4. Pull out the locking pins.

5. Fit the crimping / pressing or cutting jaws.

6. Push the locking pins in until they engage.

8 English 2207121 *2207121*

7. Rotate the tool head to the desired working position.

The tool head can be rotated much more easily when not under pressure.

5.6 Removing the crimping / pressing or cutting jaws 3

WARNING

Risk of injury! Unintentional starting.

▶Remove the battery before fitting, changing or removing the crimping /pressing or cutting jaws.

1. Remove the battery and rotate the head of the tool to the outset position.

2. Press the locking pins.

3. Rotate the locking pins counterclockwise as far as they will go.

4. Pull out the locking pins.

5. Remove the crimping / pressing or cutting jaws toward the nose of the tool.

5.7 Inserting the crimping die (only for crimping jaws with crimping dies) 4

WARNING

Risk of injury! Unintentional starting.

▶Remove the battery before fitting, changing or removing the crimping / pressing die.

Never operate the tool without a crimping / pressing die in place.

1. Remove the battery.

2. Select a suitable crimping die. Push the two halves of the crimping / pressing die in until they engage.

5.8 Removing the crimping die (only for crimping jaws with crimping dies) 5

WARNING

Risk of injury! Unintentional starting.

▶Remove the battery before fitting, changing or removing the crimping / pressing die.

1. Remove the battery.

2. Pull back the locking mechanism and remove the two halves of the crimping die.

5.9 Changing the cutting edges 6

WARNING

Risk of injury! Unintentional starting.

▶Remove the battery before inserting, changing or removing cutting edges.

1. Remove the battery.

2. Unscrew the cutting edge securing screws.

3. Remove the cutting edges by pulling them out toward the front end of the tool.

4. Insert the new cutting edges in the tool.

5. Tighten the cutting edge securing screws.

*2207121* 2207121 English 9

5.10 Crimping 7

WARNING

Danger! Risk of fire due to faulty crimping.

▶Use crimping terminals of the correct type and size for the cable and with the corresponding crimping

dies. Failure to observe this point can result in faulty crimping.

▶Listen for the signal tone and check that the piston has retracted. If no signal tone is heard or if the piston

does not retract then the crimping is faulty.

1. Insert the connector in the open crimping die.

In cold weather the hydraulic oil can thicken and slow the pressing operation. Perform 5 to 10

empty pressing operations to heat up the pressing tool.

2. Press the control switch.

3. Keep the control switch pressed until the piston has retracted.

4. Repeat the crimping operation if necessary, beginning at A and moving in the direction of arrow B,

carrying out the number of crimping operations given in the tables.

5.11 Making the cut 8

WARNING

Risk of injury! Risk of serious injury during the cutting operation.

▶Throughout the cutting operation, take great care to keep your hands and fingers well clear of the cutting

jaws.

In cold weather the hydraulic oil can thicken and slow the pressing operation. Perform 5 to 10 empty

pressing operations to heat up the pressing tool.

1. Place the material to be cut in the open cutting jaws or hold the tool with open cutting jaws against the

material to be cut.

Always make sure that the material to be cut is fully inserted into the cutting head.

Do not exceed the maximum cutting capacity.

Do not attempt to cut material that cannot be inserted fully into the cutting head.

2. Press the control switch.

3. Keep the control switch pressed until the piston has retracted.

6 Care and maintenance

WARNING

Risk of injury with battery inserted !

▶Always remove the battery before carrying out care and maintenance tasks!

Care of the product

• Carefully remove stubborn dirt.

• Carefully clean the air vents, if present, with a dry, soft brush.

• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

• Use a dry, clean cloth to clean the contacts of the product.

Care of the Liion batteries

• Never use a battery with clogged air vents. Clean the air vents carefully using a dry, soft brush.

• Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of

moisture (e.g. by being dipped in water or left in the rain).

If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable

container and consult Hilti Service.

10 English 2207121 *2207121*

• Keep the battery free of extraneous oil and grease. Do not permit dust or dirt to accumulate unnecessarily

on the battery. Clean the battery with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents

containing silicone as these can attack the plastic parts.

Do not touch the contacts of the battery and do not remove the factory-applied grease from the contacts.

• Use only a slightly damp cloth to clean the housing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all

function correctly.

• Do not use the product if signs of damage are found or if parts malfunction. Immediately have the product

repaired by Hilti Service.

• After cleaning and maintenance, install all guards and protective devices and check that they are in full

working order.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with your product can be found at your

Hilti Store or online at: www.hilti.group

7 Transport and storage of cordless tools and batteries

Transport

CAUTION

Accidental starting during transport !

▶Always transport your products with the batteries removed!

▶Remove the battery/batteries.

▶Never transport batteries loose and unprotected. During transport, batteries should be protected from

excessive shock and vibration and isolated from any conductive materials or other batteries that may

come in contact with the terminals and cause a short circuit. Comply with the locally applicable

regulations for transporting batteries.

▶Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged

batteries.

▶Prior to each use and before and after prolonged transport, check the product and the batteries for

damage.

Storage

WARNING

Accidental damage caused by defective or leaking batteries !

▶Always store your products with the batteries removed!

▶Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in

the technical data.

▶Do not store batteries on the charger. Always remove the battery from the charger when the charging

operation has completed.

▶Never leave batteries in direct sunlight, on sources of heat, or behind glass.

▶Store the product and batteries where they cannot be accessed by children or unauthorized persons.

▶Prior to each use and before and after prolonged storage, check the product and the batteries for

damage.

8 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by

yourself, please contact Hilti Service.

8.1 The crimping / cutting tool is not in working order.

Malfunction Possible cause Action to be taken

The LEDs on the battery indi-

cate nothing.

The battery is not correctly in-

serted.

▶Push the battery in until it

engages with a double click.

*2207121* 2207121 English 11

Malfunction Possible cause Action to be taken

The LEDs on the battery indi-

cate nothing.

Battery is discharged. ▶Change the battery and charge

the empty battery.

The battery is too hot or too cold. ▶Allow the battery to cool

down or to warm up to room

temperature.

1 LED on the battery blinks. Battery is discharged. ▶Change the battery and charge

the empty battery.

The battery is too hot or too cold. ▶Allow the battery to cool

down or to warm up to room

temperature.

4 LEDs on the battery blink. The crimping tool has been briefly

overloaded.

▶Allow the tool to cool down.

Red LED => lights continu-

ously and a warning tone is

emitted.

Technical problem. ▶Incorrect operation is possible!

Contact Hilti Service.

Red LED => blinks at short

intervals and a warning tone

is emitted.

The state of charge of the battery

is too low to allow a complete op-

erating cycle.

▶Change the battery and charge

the empty battery.

Red LED => lights briefly and

no warning tone is emitted.

The tool has overheated. ▶Allow the tool to cool down.

8.2 The crimping / cutting tool is in working order.

Trouble or fault Possible cause Action to be taken

The battery runs down more

quickly than usual.

Very low ambient temperature. ▶Allow the battery to warm up

slowly to room temperature.

The battery does not en-

gage with an audible "double

click".

The retaining lugs on the battery

are dirty.

▶Clean the retaining lugs and refit

the battery.

Red LED => blinks at long

intervals and a warning tone

is emitted.

Crimping / pressing pressure not

achieved (tool was used incorrect-

ly).

▶Make sure that the tool is used

correctly and check the crimped

/ pressed part if unsure.

Red LED => lights continu-

ously and a warning tone is

emitted.

Technical problem. ▶Incorrect operation is possible!

Contact Hilti Service.

9 Disposal

WARNING

Risk of injury due to incorrect disposal! Health hazards due to escaping gases or liquids.

▶DO NOT send batteries through the mail!

▶Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting.

▶Dispose of your battery out of the reach of children.

▶Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public

health and safety resources for disposal instructions.

Most of the materials from which Hilti products are manufactured can be recycled. The materials must be

correctly separated before they can be recycled. In many countries, your old tools, machines or appliances

can be returned to Hilti for recycling. Ask Hilti Service or your Hilti sales representative for further information.

▶Do not dispose of power tools, electronic equipment or batteries as household waste!

12 Русский 2207121 *2207121*

10 Manufacturer’s warranty

▶Please contact your local Hilti representative if you have questions about the warranty conditions.

11 Further information

For more information on operation, technology, environment and recycling, follow this link:

qr.hilti.com/manual?id=2207120&id=2207121

This link is also to be found at the end of the documentation, in the form of a QR code.

Перевод оригинального руководства по эксплуатации

1 Указания к документации

1.1 Об этом документе

Импортер и уполномоченная изготовителем организация

• (RU) Российская Федераци

АО "Хилти Дистрибьюшн ЛТД", 141402, Московская область, г. Химки, ул. Ленинградская, стр. 25

• (BY) Республика Беларусь

222750, Минская область, Дзержинский район, Р-1, 18-й км, 2 (около д. Слободка), помещение

1-34

• (KZ) Республика Казахстан

Республика Казахстан, индекс 050011, г. Алматы, ул. Пугачева 4

• (KG) Киргизская Республика

OcOO "T AND T", 720021, Кыргызстан, Бишкек,ул. Ибраимова 29 А

• (AM) Республика Армения

ООО Эйч-Кон, Республика Армения, г. Ереван, ул. Бабаяна 10/1

Страна производства: см. маркировочную табличку на оборудовании.

Дата производства: см. маркировочную табличку на оборудовании.

Соответствующий сертификат можно найти по адресу: www.hilti.ru

Специальных требований к условиям хранения, транспортировки и использования, кроме указанных в

руководстве по эксплуатации, нет.

Срок службы изделия составляет 10 лет.

• Ознакомьтесь с этим документом перед началом работы. Это является залогом безопасной работы

и бесперебойной эксплуатации.

• Соблюдайте указания по технике безопасности и предупреждающие указания, приводимые в

данном документе и на изделии.

• Храните руководство по эксплуатации всегда рядом с электроинструментом и передавайте элек-

троинструмент будущим владельцам только вместе с этим руководством.

1.2 Пояснение к знакам

1.2.1 Предупреждающие указания

Предупреждающие указания служат для предупреждения об опасностях при обращении с изделием.

Используются следующие сигнальные слова:

ОПАСНО

ОПАСНО !

▶Общее обозначение непосредственной опасной ситуации, которая влечет за собой тяжелые травмы

или смертельный исход.

*2207121* 2207121 Русский 13

ПРЕДУПРЕЖДЕНИЕ

ПРЕДУПРЕЖДЕНИЕ !

▶Общее обозначение потенциально опасной ситуации, которая может повлечь за собой тяжелые

травмы или смертельный исход.

ОСТОРОЖНО

ОСТОРОЖНО !

▶Общее обозначение потенциально опасной ситуации, которая может повлечь за собой травмы или

повреждение оборудования (материальный ущерб).

1.2.2 Символы, используемые в руководстве

В этом руководстве используются следующие символы:

Соблюдать руководство по эксплуатации

Указания по эксплуатации и другая полезная информация

Обращение с материалами, пригодными для вторичной переработки

Не выбрасывайте электроинструменты и аккумуляторы вместе с обычным мусором!

Hilti Литий-ионный аккумулятор (Li-Ion)

Зарядное устройство Hilti

1.2.3 Символы на изображениях

На изображениях используются следующие символы:

Эти цифры указывают на соответствующее изображение в начале данного руководства.

Нумерация на изображениях отображает порядок выполнения рабочих операций и может

отличаться от нумерации, используемой в тексте.

Номера позиций используются в обзорном изображении. В обзоре изделия они указывают

на номера в экспликации.

Этот знак должен привлечь особое внимание пользователя при обращении с изделием.

1.3 Символы на инструменте

1.3.1 Символы

Используются следующие символы:

Опасность защемления!

Опасность порезов!

Использовать защитные очки!

Изделие поддерживает технологию NFC, совместимую с платформами iOS и Android.

Постоянный ток

Литий-ионный аккумулятор

Серия используемых литий-ионных аккумуляторов Hilti. Соблюдайте указания, приведенные

в главе Использование по назначению.

Никогда не используйте аккумулятор в качестве ударного инструмента.

14 Русский 2207121 *2207121*

Не допускайте падения аккумулятора. Не используйте аккумулятор, который получил повре-

ждения вследствие удара или каким-либо иным образом.

Соответствующая маркировка на изделии подтверждает, что это изделие было сертифици-

ровано данным органом сертификации для использования в США и Канаде в соответствии с

действующими нормами.

1.4 Информация об изделии

Изделия предназначены для профессионального использования, поэтому они должны

обслуживаться и ремонтироваться только уполномоченным и обученным персоналом. Этот персонал

должен пройти специальный инструктаж по технике безопасности. Использование изделия и его

оснастки не по назначению или его эксплуатация необученным персоналом могут представлять

опасность.

Типовое обозначение и серийный номер указаны на заводской табличке.

▶Перепишите серийный номер в нижеприведенную табличную форму. Данные изделия необходимы

при обращении в наше представительство или сервисный центр.

Указания к изделию

Комбинированный (обжимно-режущий)

инструмент

NUN 054 IE-A22

Поколение 01

Серийный №

1.5 Декларация соответствия нормам

Настоящим фирма-изготовитель с полной ответственностью заявляет, что данное изделие соответ-

ствует действующим директивам и нормам. Копию декларации соответствия нормам см. в конце этого

документа.

Техническая документация (оригиналы) хранится здесь:

Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, Германия

2 Безопасность

2.1 Общие указания по технике безопасности для электроинструментов

ПРЕДУПРЕЖДЕНИЕ Изучите все указания по технике безопасности, инструкции, иллюстрации

и технические данные, которые прилагаются к данному электроинструменту. Несоблюдение

приводимых ниже указаний может привести к поражению электрическим током, пожару и/или тяжелым

травмам.

Сохраните все указания по технике безопасности и инструкции для следующего пользователя.

Используемый далее термин «электроинструмент» относится к электроинструменту, работающему от

электрической сети (с кабелем электропитания) и от аккумулятора (без кабеля электропитания).

Безопасность рабочего места

▶Следите за чистотой и хорошей освещенностью на рабочем месте. Беспорядок на рабочем

месте или плохое освещение могут привести к несчастным случаям.

▶Не используйте электроустройство/электроинструмент во взрывоопасной зоне, где имеются

горючие жидкости, газы или пыль. При работе электроустройство/электроинструмент искрит, и

искры могут воспламенить пыль или пары/газы.

▶Не разрешайте детям и посторонним приближаться к работающему

электроустройству/электроинструменту. Отвлекаясь от работы, можно потерять контроль над

электроустройством/электроинструментом.

Электрическая безопасность

▶Соединительная вилка электроинструмента должна соответствовать розетке электросети.

Не изменяйте конструкцию вилки! Не используйте переходные вилки с электроинстру-

ментами с защитным заземлением. Использование оригинальных вилок и соответствующих им

розеток снижает риск поражения электрическим током.

▶Избегайте непосредственного контакта с заземленными поверхностями, например с трубами,

отопительными приборами, газо-/электропластинами и холодильниками. При контакте с

заземленными предметами возникает повышенный риск поражения электрическим током.

Страница загружается...

Hilti NUN 054 IE-A22 Руководство пользователя

Похожие модели бренда