Yamaha WX-010BL Руководство пользователя

UABGLV

OWNER'S MANUAL

Before using this unit, be sure to read the “Safety Brochure” and “Quick Manual.”

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided

for your safety. If the provided plug does not fit into

your outlet, consult an electrician for replacement of

the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the

apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate

normally, or has been dropped.

Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out

of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without

annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing

damage from loud sounds is often undetectable until it is too late, Yamaha and the Electronic Industries

Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive

volume levels.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK DO

NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert you to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral

triangle is intended to alert you to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

IMPORTANT

Please record the serial number of this unit in the space

below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit. Retain

this Owner’s Manual in a safe place for future reference.

We Want You Listening For A Lifetime

This device complies with part 15 of FCC Rules and Industry Canada’s licence-exempt RSSs. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC INFORMATION (for US customers)

1 IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved

by Yamaha may void your authority, granted by the

FCC, to use the product.

2 IMPORTANT: When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation

instructions. Failure to follow instructions could void

your FCC authorization to use this product in the

USA.

3 NOTE: This product has been tested and found to

comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices.

Compliance with these requirements provides a

reasonable level of assurance that your use of this

product in a residential environment will not result in

harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and,

if not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If

this product is found to be the source of interference,

which can be determined by turning the unit “OFF”

and “ON”, please try to eliminate the problem by

using one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch

(circuit breaker or fuse) circuits or install AC line

filter/s.

In the case of radio or TV interference, relocate/

reorient the antenna. If the antenna lead-in is 300 ohm

ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce

satisfactory results, please contact the local retailer

authorized to distribute this type of product. If you can

not locate the appropriate retailer, please contact

Yamaha Corporation of America A/V Division, 6660

Orangethorpe Ave., Buena Park, CA 90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the

FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This

equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body.

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

FCC CAUTION

Change or modifications not expressly approved by the

party responsible for compliance could void the user’s

authority to operate the equipment.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

CAN ICE-3 (B)/NMB-3 (B)

iii

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this unit in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources,

vibration, dust, moisture and cold. For proper

ventilation, allow the following minimum clearances.

Top: 5 cm (2 in)

Rear: 5 cm (2 in)

Sides: 5 cm (2 in)

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds.

4 Do not expose this unit to sudden temperature

changes from cold to hot (or vice versa), and do not

locate this unit in an environment with high humidity

(i.e., a room with a humidifier) to prevent

condensation inside this unit, which may cause an

electrical shock, fire, damage to this unit, and/or

personal injury.

5 Avoid installing this unit where foreign object may

fall onto this unit and/or this unit may be exposed to

liquid dripping or splashing. On the top of this unit,

do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Burning objects (i.e., candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall

and liquid may cause electrical shock to the user

and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If

the temperature inside this unit rises, it may cause

fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall

outlet, grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than specified is

dangerous and may cause fire, damage to this unit,

and/or personal injury. Yamaha will not be held

responsible for any damage resulting from use of this

unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power

cable and outdoor antennas disconnected from a wall

outlet or this unit during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

15 When not planning to use this unit for long periods of

time (i.e., vacation), disconnect the AC power plug

from the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding that

this unit is faulty.

17 Before moving this unit, press to set the unit to

off, and disconnect the AC power plug from the wall

outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may

become warm. Turn the unit off, then leave this unit

alone for cooling.

20 Install this unit near the wall outlet and where the AC

power plug can be reached easily.

21 Be sure to use the power cable supplied with this

unit. Using a power cable other than the one provided

may cause fire or damage to this unit.

◆ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source

as long as it is connected to the wall outlet, even if this

unit itself is turned off by . In this state, this unit is

designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

• This unit’s speakers use magnets. Do not place items

that are sensitive to magnetism, such as CRT-type TVs,

clocks, credit cards, floppy disks, etc., on or beside this

unit.

• There is a chance that placing this unit too close to a

CRT-based (Braun tube) TV set might impair picture

color. Should this happen, move this unit away from the

TV set.

◆ Special Instructions for U.K.

Model

 About this manual

• “iPhone” described in this manual may also refer to “iPod”

or “iPad.”

• Illustrations may differ from actual item depicted.

• Symbols:

Indicates precautions for use of the unit and its

feature limitations.

Indicates supplementary explanations for better

use.

Indicates the corresponding reference page(s).

IMPORTANT

THE WIRES IN MAINS LEAD ARE

COLOURED IN ACCORDANCE WITH THE

FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured BLUE must be

connected to the terminal which is marked with the

letter N or coloured BLACK. The wire which is

coloured BROWN must be connected to the

terminal which is marked with the letter L or

coloured RED.

Make sure that neither core is connected to the

earth terminal of the three pin plug.

Information for Users on Collection

and Disposal of Old Equipment:

This symbol on the products, packaging,

and/or accompanying documents means

that used electrical and electronic products

should not be mixed with general

household waste.

For proper treatment, recovery and

recycling of old products, please take them

to applicable collection points, in

accordance with your national legislation.

By disposing of these products correctly,

you will help to save valuable resources

and prevent any potential negative effects

on human health and the environment

which could otherwise arise from

inappropriate waste handling.

For more information about collection and

recycling of old products, please contact

your local municipality, your waste

disposal service or the point of sale where

you purchased the items.

For business users in the European

Union:

If you wish to discard electrical and

electronic equipment, please contact your

dealer or supplier for further information.

Information on Disposal in other

Countries outside the European

Union:

This symbol is only valid in the European

Union. If you wish to discard these items,

please contact your local authorities or dealer

and ask for the correct method of disposal.

If there should be color blotching or noise when

used near a TV, move this unit away from the TV

when using it.

Do not use this unit within 22 cm (9 inches) of

persons with a heart pacemaker implant or

defibrillator implant.

Radio waves may affect electro-medical devices.

Do not use this unit near medical devices or inside

medical facilities.

The user shall not reverse engineer, decompile,

alter, translate or disassemble the software used in

this unit, whether in part or in whole. For

corporate users, employees of the corporation

itself as well as its business partners shall observe

the contractual bans stipulated within this clause.

If the stipulations of this clause and this contract

cannot be observed, the user shall immediately

discontinue using the software.

Note

☞

Smooth operation and wireless music playback using iPhone/Android

devices

• By installing the free dedicated app “MusicCast CONTROLLER” on your iPhone/iPad/iPod touch or Android device, you

will be able to set up a network, make various settings, and select songs to play back. You can also use these devices as a

remote controller (☞ P.7).

• Equipped with Wi-Fi, which allows the unit to connect to the wireless router (access point) without any cables.

Plays various supported content with high quality sound

• Plays music from DLNA servers/Internet radio (☞ P.17), AirPlay and Bluetooth.

• Rich sound provided by the two-way speaker, large passive radiator, and DSP (Digital Signal Processor) developed by

Yamaha.

• Enhanced treble and thick mid/bass sound, even when playing a compressed audio source, such as MP3. (Music Enhancer)

Supports streaming services

• You can enjoy music from a variety streaming services. (Supported music streaming services vary by the country or region of

use.)

Stereo Pair function

• You can enjoy stereo reproduction using two WX-010 units.

FEATURES

WX-010

 INTRODUCTION

SUPPLIED ACCESSORIES...................................2

PART NAME ..........................................................3

 PREPARATION

INSTALLATION .....................................................4

Mounting the unit on a wall

(Except for U.S.A. and Canada model)..........4

TURNING ON THE POWER ..................................5

CONNECTING TO THE NETWORK ......................6

HOME AUDIO NETWORK WITH MusicCast........7

Connecting to the network using MusicCast

CONTROLLER ..............................................7

CONNECTING TO THE NETWORK BY

SHARING THE iOS DEVICE SETTING .................9

 LISTENING TO THE MUSIC

LISTENING TO THE INTERNET RADIO.............10

LISTENING TO THE SONGS IN THE

COMPUTER AND NAS ........................................10

Setting the media sharing of music files...........10

PLAYING BACK MUSIC WITH AirPlay ..............11

Playback of iTunes/iPhone music contents......11

Clearing AirPlay................................................11

LISTENING TO MUSIC FROM YOUR Bluetooth

DEVICE ................................................................12

Pairing this unit with your Bluetooth device......12

Connecting an already-paired device via

Bluetooth......................................................12

Disconnecting a Bluetooth connection .............12

Listening to music through wireless

headphones .................................................13

 OTHER FUNCTIONS AND

INFORMATION

STEREO PAIR .....................................................14

Setting/Playing back music ..............................14

Canceling Stereo Pair ......................................15

UPDATING THE FIRMWARE ..............................16

OPTION SETTINGS .............................................16

ADDITIONAL INFORMATION .............................17

TRADEMARKS ....................................................17

TROUBLESHOOTING .........................................18

General.............................................................18

MusicCast.........................................................18

Network ............................................................18

Bluetooth ..........................................................20

SUPPORTED DEVICES/MEDIA AND FILE

FORMATS ............................................................21

SPECIFICATIONS................................................22

INTRODUCTION

CONTENTS

SUPPLIED ACCESSORIES



Power cable



Anti-vibration pad

To prevent the vibration from the sound from reaching

the wall, attach the Anti-vibration pads on the four

corners of the rear panel.

(Except for U.S.A.

and Canada model)



Quick Manual



Safety Brochure

■ Top panel

(power)/CONNECT (☞ P.5, 7)

Turns down the volume.

Turns up the volume.

Plays/pauses.

Bluetooth indicator

Lights during Bl uetooth connection.

Power indicator

Lights while the unit is turned on.

Wi-Fi indicator

Lights while the unit is connected to the wireless (Wi-Fi)

network.

, , , are touch sensors. They react when you touch them with your finger.

If the volume reaches the maximum/minimum value, these three indicators (

, , ) flash twice at the same time.

■ Rear panel

Key hole slot (☞ P.4)

(Except for U.S.A. and Canada model)

Wall mount hanger hole (☞ P.5)

Use to mount the unit to a wall mount hanger.

Power connector (☞ P.5)

Network terminal (☞ P.6)

Use a network cable (commercially available) to connect

to the network.

If you use the unit with Wi-Fi, a network cable is not

necessary to connect to the unit.

PART NAME

Note

PREPARATION

Plug the power cable into the wall outlet after completing installation.

• Placing the unit too close to a CRT TV may impair the picture color or cause a buzzing noise. In this case, move the unit at

least 20 cm (8") away from the TV. This is not an issue with LCD and plasma TVs.

• Install in a stable place, being careful of the following points:

– Do not place on top of steel or other metal plates.

– Do not cover with a cloth, etc.

You can mount the unit on the wall as follows.

Install screw (commercially available) into a solid wall or wall support as shown in the illustration. Use 3.5 to 4 mm (1/8")

diameter self-tapping screw.

Hang the unit by its keyhole slot onto the protruding screw.

• Make sure the shaft of the screw is seated in the narrow part of the keyhole slot. Otherwise, the unit may fall.

• Do not mount the unit on thin plywood or on a wall with a soft surface material. Otherwise, the screw may pull out of the

surface and the unit may fall, possibly damaging the unit or causing personal injury.

• Do not affix the unit to a wall using nails, adhesives, or unstable hardware. Long-term use and vibration may cause the unit to

fall.

• To avoid accidents resulting from tripping over loose cables (such as a power cable), affix the cables to the wall.

• When using the brackets to mount the unit on a wall / ceiling, please use safety wire (not included) between the unit and the

bracket to prevent the unit from falling.

• If you are not sure of a safe way to install the unit, consult a professional installer or a building contractor.

• To prevent the vibration from the sound from reaching the wall, attach the Anti-vibration pads on the four corners of the rear

panel (☞ P.2).

INSTALLATION

Note

Mounting the unit on a wall (Except for U.S.A. and Canada model)

Wall/wall support

Minimum

20 mm (3/4")

5 mm

(1/4")

WX-010

1.7 kg (3.7 lbs.)

Note

TURNING ON THE POWER

■ To mount the unit to a wall mount hanger

The unit can be mounted to the wall using a commerciallyavailable wall mount hanger. Use the wall mount hanger hole on the

rear panel to mount.

Use a wall mount hanger that is compatible for a unified coarse screw, such as those used for the tripod stand of a camera.

• If using a wall mount hanger, use the one compatible for this unit.

• Use the wall mount hanger whose withstand load capacity is over 4.5 kg (10 lbs.).

• Follow the instructions in the owner’s manual of the wall mount hanger and mount the unit correctly.

• If you mount the unit incorrectly or use a wall mount hanger that is not compatible for the unit, the unit may fall and cause

injury.

• Check the safety after mounting the unit. Yamaha is not responsible for any accidents which may be caused due to an

incorrect installation position or incorrect installation methods, or for any malfunction of the wall mount hanger. If you are

worried about the safety, ask a professional to install.

Rear panel

120 mm (4-3/4")

60 mm (2-3/8")

58mm

(2-1/4")

WX-010

1.7 kg

(3.7 lbs.)

160 mm (6-1/4")

Minimum

5 mm (1/4")

Specification of mounting screw:

UNC 1/4-20

Specifications of the screw hole

Diameter 6.35 mm (1/4")

Screw thread 20 (per 1")

Diameter 6.35 mm (1/4")

Depth 9 mm (3/8")

WX-010

Note

TURNING ON THE POWER

Plug the power cable into the wall outlet and

tap (power)/CONNECT.

The unit turns on and the power indicator lights. If you

tap again, the unit turns off (standby) and the power

indicator turns off.

• After the power plug is inserted into the wall outlet, it

takes about 10 seconds for the touch sensors to be

adjusted. In order to prevent malfunction of the touch

sensors, do not touch them ( (power)/CONNECT/

// ) or play back for about 10 seconds.

y Auto Standby

If about 20 minutes have elapsed with no playback and no

operation while the unit is on, it will automatically enter

standby.

You can change the auto standby function setting in the

MusicCast CONTROLLER app (☞ P.7). Tap

(Settings) in the room select display, and then change the

setting.

Power cable

Power indicator

Tap (power)/CONNECT.

Rear pannel

Top pannel

Note

Connect the unit to the network as shown below.

• For details on Internet connection, refer to the owner’s manuals of your connecting devices.

• Some security software installed on your PC or the firewall settings of connecting devices (such as a router) may block the

access of the unit to the connecting devices or the Internet. In this case, change the setting of the security software or

connecting devices.

• If you connect the unit to the network with a network cable, connect with a commercially available STP (shielded twisted

pair) network cable (straight, CAT-5 or higher).

• Using the MusicCast CONTROLLER app, make sure that the unit and other connecting devices are connected to the same

router (☞ P.7).

CONNECTING TO THE NETWORK

LAN

WAN

Internet

Modem

Wireless

router

This unit

Tablet

Smartphone

NAS

(Network attached storage)

Network cable

Wired or wireless

MusicCast is a brand new wireless musical solution from Yamaha, allowing you to share music among all of your rooms with a

variety of devices. You can enjoy music from your smartphone, PC, NAS drive and music streaming service anywhere in your

house with one easy-to-use app. For more details and a lineup of MusicCast compatible products, visit our website.

http://www.yamaha.com/musiccast/

■ MusicCast CONTROLLER

• Main functions

- Basic operations such as turning the unit on/off and,

volume adjustment

- Select/play/pause the music

- Play music in the devices

- Listening to the Internet radio

- Listening to the songs in the computer and NAS

- Playing back music with AirPlay

- Listening to music from your Bluetooth device

- Using the equalizer

- Using the sleep timer

- Updating the firmware

• System requirements

- For details, search App Store or Google Play

for “MusicCast CONTROLLER.”

• The application supports iPhone/iPad/iPod touch and Android mobile devices.

For details, refer to the instructions for this app in each store.

- Wireless network environment.

■ Mobile device (smartphone, etc.)

To use the unit, you need the dedicated app “MusicCast CONTROLLER” for the operation.

HOME AUDIO NETWORK WITH MusicCast

Connecting to the network using MusicCast CONTROLLER

Install the MusicCast CONTROLLER app to

the mobile device.

Start the app.

After the app starts, select “Setup.”

If you have already connected a MusicCast compatible

device to the network, tap (Settings) in the room

select display and then add this unit as a new device.

Turn on the unit.

The power indicator lights.

Touch and hold the (power)/CONNECT

on the unit for 5 seconds.

The Wi-Fi and the Bluetooth indicators flash quickly.

Follow the guidance displayed in the app to set.

Follow the instructions in the MusicCast

CONTROLLER app to play music.

(power)/

CONNECT

Wi-Fi indicator

Bluetooth indicator

Power indicator

If your router supports multiple SSID’s (network names), connect the mobile device to the first access point (“SSID 1”,

etc.)

HOME AUDIO NETWORK WITH MusicCast

■ Setting of the devices and playback

Create the following network (MusicCast Network) using the MusicCast CONTROLLER app.

If you want to install a MusicCast compatible device to a location that is out of range of the wireless router, connect another

MusicCast support device to the router with a network cable to extend the range (Extend mode).

Depending on where it is placed, the MusicCast compatible device may not be able to play back a high-resolution audio source.

In this case, connect the device directly to the router with a network cable.

WX-010

Wireless router

Standard Mode

Extend Mode

WX-010

When you turn on the unit for the first time after purchase or initialize the unit (☞ P.16), the Wi-Fi indicator blinks and the unit

automatically starts to search iOS device (such as iPhone). You can easily setup a wireless connection by applying the network

settings on iOS devices.

Before proceeding, confirm that your iOS device is connected to a wireless router (access point).

This setting does not need to be specified if the unit is connected to a network with “MusicCast CONTROLLER.”

Display the Wi-Fi setup screen on the iOS device and select the unit from “SETUP A NEW

AIRPLAY SPEAKER...”.

• Follow the on-screen instructions displayed on the iOS device.

• In order to enjoy all of the unit’s functions, connect it to a network with “MusicCast CONTROLLER.” (☞ P.7)

• You need iOS device with iOS 7.1 or later.

• The network settings on iOS devices cannot be applied to the unit to establish a wireless connection if your wireless router

(access point) uses WEP encryption.

CONNECTING TO THE NETWORK BY SHARING THE

iOS DEVICE SETTING

Note

LISTENING TO THE MUSIC

You can listen to world-wide radio stations via Internet. After connecting the unit to the network, use the MusicCast

CONTROLLER app (☞ P.7) to play the radio.

You can use the advanced feature of vTuner (such as adding a new station to the list) by accessing the following website with

the web browser on your PC.

http://yradio.vtuner.com/

- Before registering the Internet radio station, play any Internet radio station with this unit.

- To create a necessary account for registration, you need the vTuner ID of this unit and your e-mail address. You can check the

vTuner ID in the MusicCast CONTROLLER app. (☞ P.7)

Tap (Settings) in the room select display and then check the unit information.

This unit allows you to play back music files such as MP3, WMA, or FLAC (lossless audio data compression format) files

stored in the computer (server) connected to the network or NAS.

To play back music files in your computer with this unit, you need to make the media sharing setting between the unit and

computer (Windows Media Player 11 or later). The following instructions use Windows Media Player 12 in Windows 7 as an

example.

■ For Windows Media Player 12

LISTENING TO THE INTERNET RADIO

LISTENING TO THE SONGS IN THE COMPUTER AND NAS

Setting the media sharing of music files

Start Windows Media Player 12 on your PC.

Select “Stream”, then “Turn on media

streaming.”

The control panel window of your PC is shown.

Click “Turn on media streaming.”

Select “Allowed” from the drop-down list

next to “WX-010.”

The names on the list are device names (Room names).

You can set Room names on (Settings) in the room

select display. If the Room name is not set, the Room

name is “WX-010 ***.” (*** is an arbitrary number.)

Click “OK” to exit.

For details on media sharing settings, refer to Windows

Media Player help.

Turn on media streaming...

Turn on media streaming

Only setting the media sharing is explained in this section.

After setting, operate Windows Media Player with your

PC as usual to play back.

WX-010



Allowed

PLAYING BACK MUSIC WITH AirPlay

Playing abundant supported contents with high quality sound from AirPlay.

The AirPlay function allows you to play back iTunes/iPhone music on the unit wirelessly via a network.

Follow the procedure below to play back iTunes/iPhone music contents on the unit.

Click/tap on the iTunes/iPhone screen and select a device other than WX-010 from the speaker list. Or, change the source

to other than AirPlay, using “MusicCast CONTROLLER.”

◆ For Windows Media Player 11

Start the Windows Media Player 11 on your PC.

Select “Library” then “Media Sharing.”

Check the “Share my media to” box, select the “WX-010” icon, and click “Allow.”

The names on the list are device names (Room names). You can set Room names on (Settings) in the room select

display. If the Room name is not set, the Room name is “WX-010 ***.” (*** is an arbitrary number.)

Click “OK” to exit.

◆ For a PC or a NAS with other DLNA server software installed

Refer to the owner’s manual of your device or software and configure the media sharing settings.

PLAYING BACK MUSIC WITH AirPlay

Playback of iTunes/iPhone music contents

Turn on the unit, and start iTunes on the PC

or display the playback screen on the

iPhone.

If the iTunes/iPhone recognizes the unit, the AirPlay

icon ( ) appears.

On the iTunes/iPhone, click (tap) the AirPlay

icon and select the unit (room name of the

unit) as the audio output device.

Select a song and start playback.

The source automatically switches to “AirPlay” and

playback starts (except in the eco standby).

Clearing AirPlay

iPhone

iTunes

(example)

iPhone iOS9

(example)

iTunes

(example)

iPhone iOS9

(example)

The unit’s room name is

displayed where “-------” is

indicated above.

This unit provides Bluetooth functionality. You can enjoy wireless music playback from your Bluetooth device

(smartphone, digital audio player, etc.). Please also refer to the owner’s manual of your Bluetooth device.

• Install in the same room as the device with which signals are to be exchanged (Bluetooth profile A2DP

compatible smartphone, digital audio player, etc.) within a direct line-of-sight distance of 10 m (33 ft).

• Make sure there are no obstacles between this unit and the Bluetooth device.

■ Pairing (Registration)

■ Connecting from the connecting device

In the Bluetooth settings of the connecting device, turn Bluetooth on.

From the Bluetooth connection list of the connecting device, choose this unit (the Room name of

this unit ☞ P.10).

The Bluetooth connection will be established, and the Bluetooth indicator will light.

If any of the following operations are performed while a Bluetooth connection is established, the Bluetooth

connection will be disconnected.

• Tapping (power)/CONNECT to enter standby.

• Touching and holding for 3 seconds.

• Disconnecting the Bluetooth connection from the connecting device.

LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE

Pairing this unit with your Bluetooth device

Turn on the unit.

The power indicator lights.

On your connecting device (mobile device),

set Bluetooth to on.

Perform Bluetooth pairing on the connecting

device.

For details, refer to the owner’s manual of the connecting

device.

From the Bluetooth connection list of the

connecting device, choose this unit (the

Room name of this unit ☞ P.10).

• Finish the operation from turning on the unit to completing

pairing in 5 minutes.

• If you are asked to enter a password, enter the numerals

“0000.”

Connecting an already-paired device via Bluetooth

Disconnecting a Bluetooth connection

(power)/CONNECT

Power indicator

-------

The unit’s Room name is displayed where

“-------” is indicated above.

Check that the pairing process on the connecting device

has been completed. If the pairing process fails, start over

from step . For details, see the connecting device’s

owner's manual.

Note

LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE

You can listen to the audio played back by this unit through Bluetooth-compatible wireless headphones. The audio will be

transmitted to the wireless headphones using “MusicCast CONTROLLER” installed on your mobile device.

Listening to music through wireless headphones

Set the

Bluetooth

connection for the

Bluetooth

device (wireless headphones, etc.) to standby.

Tap in the playback display of

“MusicCast CONTROLLER.”

Tap “Bluetooth Transmission.”

Select the Bluetooth device (wireless

headphones, etc.).

When the connection is established, the Bluetooth

indicator (☞ P.3) lights up.

Tap “Done.”

The sound is output by the receiving Bluetooth

device (wireless headphones, etc.).

•Use Bluetooth devices compatible with the A2DP profile.

• Audio from AirPlay or a Bluetooth device cannot be

transmitted to and output by another Bluetooth device.

• The playback sound is also output by the unit.

• The “MusicCast CONTROLLER” app displays shown here

are from an iPhone.

• For details on using your Bluetooth device, refer to its

owner’s manual.

WX-010

Bluetooth

speakers/headphones

Tap

Note

OTHER FUNCTIONS AND INFORMATION

You can use two WX-010 units to reproduce stereo sound by setting each speaker as the right

or left speaker.

Set the left and right speakers separately by following the steps below.

Connect each WX-010 to the same network by using the dedicated app “MusicCast

CONTROLLER.”

If the WX-010 is linked to another MusicCast unit, first disconnect the link by using the dedicated app “MusicCast

CONTROLLER.”

Tap (power)/CONNECT of each unit to set them to standby.

Tap and hold the following together for 3 seconds to set the left/right speakers.

1 For setting the left speaker: and

Indicators light from right to left repeatedly (refer to

of the table), and the unit enters pairing standby.

For setting the right speaker: and

Indicators light from left to right repeatedly (refer to

of the table), and the units start pairing.

Indicator display during the Stereo Pair

After paring is completed, the indicators light from the center to both sides (refer to of the table), and all indicators

return to the normal status.

Use the dedicated app “MusicCast CONTROLLER” to play back.

• You can check which speaker is the left or right speaker with the dedicated app “MusicCast CONTROLLER” (Indicators

light as

or of the table).

• In Stereo Pair mode, you can operate one speaker to simultaneously turn off both speakers or adjust the volume of both

speakers.

• If about five minutes passes while the unit cannot find the other speaker to connect to, the pairing standby will be cancelled

automatically.

• When in Stereo Pair mode, the option settings other than “Initialize the unit.” (☞ P.16) cannot be set.

The Stereo Pair setting remains even if the speakers enter standby or the power cable is unplugged and plugged again.

STEREO PAIR

• To use the Stereo Pair function, you need two

WX-010.

• Stereo Pair is available only when the Network

Standby of the unit is enabled (

☞

P.16).

Setting/Playing back music

WX-010

Left

speaker

WX-010

Right

speaker

Note

Stereo Pair

status

Indicator display

Start Pairing/

Checking the

Left and Right

Speaker

Pairing

Completed

Left speaker

Right speaker

Right-to-Left

Left-to-Right

Center to both sides

Note

STEREO PAIR

Tap (power)/CONNECT to set the left and right speakers to the standby.

Tap and hold (or ) and on either speaker together for 3 seconds.

Indicators light from both sides to the center and Stereo Pair will be canceled.

• The Stereo Pair can be canceled only during standby.

• If you cancel Stereo Pair with one of the two speakers, the other one will be canceled automatically.

• If one of the two speakers is disconnected from the network when canceling the Stereo Pair, cancel Stereo Pair on each

speaker.

Canceling Stereo Pair

Both sides to center

Indicator display

Note

Страница загружается...

Yamaha WX-010BL Руководство пользователя

Похожие модели бренда

Модели других брендов