Yamaha R-N602 Инструкция по применению

R-N602

Network Receiver

Réseau Ampli-Tuner

R-N602

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

G

i En

English

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. For proper ventilation, allow the

following minimum clearances.

Top: 30 cm (11-3/4 in)

Rear: 20 cm (7-7/8 in)

Sides: 20 cm (7-7/8 in)

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord

disconnected from a wall outlet or the unit during a lightning

storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15

When not planning to use this unit for long periods of time (i.e.

vacation), disconnect the AC power plug from the wall outlet.

16 Be sure to read the “Troubleshooting” section in the owner’s

manual on common operating errors before concluding that

this unit is faulty.

17 Before moving this unit, press A downward to turn off this

unit and then disconnect the AC power plug from the AC wall

outlet.

18 Condensation will form when the surrounding temperature

changes suddenly. Disconnect the power cable from the

outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may become

warm. Turn the system off, then leave this unit alone for

cooling.

20 Install this unit near the wall outlet and where the AC power

plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such as

sunshine, fire or the like. When you dispose of batteries,

follow your regional regulations.

22 Excessive sound pressure from earphones and headphones

can cause hearing loss.

Do not touch the surface having this label. Doing so may cause

burns. The label on the device indicates that the surface to which

the label is attached may become hot during operation.

Caution: Read this before operating your unit.

This unit is not disconnected from the AC power source as long as

it is connected to the wall outlet, even if this unit itself is turned off

by A. This state is called the standby mode. In this state, this unit is

designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

Do not use this unit within 15 cm (6 inches) of persons with a heart

pacemaker implant or defibrillator implant.

Caution: Read this before operating your unit.

ii En

English

■ Notes on remote controls and batteries

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following

conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

– dusty places

• Insert batteries according to the polarity markings (+ and -).

• Change all batteries if you notice the operation range of the

remote control narrows.

• If the batteries run out, immediately remove them from the

remote control to prevent an explosion or acid leak.

• If you find leaking batteries, discard the batteries

immediately, taking care not to touch the leaked material. If

the leaked material comes into contact with your skin or gets

into your eyes or mouth, rinse it away immediately and

consult a doctor. Clean the battery compartment thoroughly

before installing new batteries.

• Do not use old batteries together with new ones. This may

shorten the life of the new batteries or cause old batteries to

leak.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully

as these different types of batteries may have the same shape

and color.

• Before inserting new batteries, wipe the battery compartment

clean.

• Keep the batteries in a location out of reach of children.

Batteries can be dangerous if a child were to put in his or her

mouth.

• If the batteries grow old, the effective operation range of the

remote control decreases considerably. If this happens,

replace the batteries with new one as soon as possible.

• If you plan not to use the unit for a long period of time,

remove the batteries from the unit. Otherwise, the batteries

will wear out, possibly resulting in a leakage of battery liquid

that may damage the unit.

• Do not throw away batteries with general house waste.

Dispose of them correctly in accordance with your local

regulations.

Caution: Read this before operating your unit.

iii En

Bluetooth

• Bluetooth is a technology for wireless communication between

devices within an area of about 10 meters (33 ft) employing the

2.4 GHz frequency band, a band which can be used without a

license.

Handling Bluetooth communications

• The 2.4 GHz band used by Bluetooth compatible devices is a

radio band shared by many types of equipment. While

Bluetooth compatible devices use a technology minimizing the

influence of other components using the same radio band, such

influence may reduce the speed or distance of communications

and in some cases interrupt communications.

• The speed of signal transfer and the distance at which

communication is possible differs according to the distance

between the communicating devices, the presence of obstacles,

radio wave conditions and the type of equipment.

• Yamaha does not guarantee all wireless connections between

this unit and devices compatible with Bluetooth function.

Information for users on collection and

disposal of old equipment and used batteries:

These symbols on the products, packaging, and/or

accompanying documents mean that used electrical

and electronic products and batteries should not be

mixed with general household waste.

For proper treatment, recovery and recycling of old

products and used batteries, please take them to

applicable collection points, in accordance with your

national legislation.

By disposing of these products and batteries

correctly, you will help to save valuable resources

and prevent any potential negative effects on human

health and the environment which could otherwise

arise from inappropriate waste handling.

For more information about collection and recycling

of old products and batteries, please contact your

local municipality, your waste disposal service or the

point of sale where you purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic

equipment, please contact your dealer or supplier for

further information.

Information on Disposal in other Countries

outside the European Union:

These symbols are only valid in the European Union.

If you wish to discard these items, please contact

your local authorities or dealer and ask for the

correct method of disposal.

Note for the battery symbol (bottom two

symbol examples):

This symbol might be used in combination with a

chemical symbol. In this case it complies with the

requirement set by the EU Battery Directive for the

chemical involved.

Cd

1 En

PREPARATIONINTRODUCTION

BASIC

OPERATION

ADDITIONAL

INFORMATION

ADVANCED

OPERATION

English

INTRODUCTION

What you can do with this unit ................................. 2

Sources that can be played back on this unit ................. 2

Mastering useful apps (MusicCast CONTROLLER).... 3

Supplied accessories ................................................... 4

Controls and functions ............................................... 5

Front panel ..................................................................... 5

Front display .................................................................. 7

Rear panel ...................................................................... 8

Remote control............................................................... 9

PREPARATION

Connections............................................................... 11

Connecting the speakers .............................................. 12

Connecting the FM and AM antennas ......................... 13

Connecting the network cable ..................................... 14

Preparing a wireless antenna ....................................... 14

Connecting power cable .............................................. 14

Connecting to network ............................................. 15

Sharing the iOS device setting..................................... 16

Using the WPS push button configuration .................. 17

Set the wireless network connection manually............ 18

Connecting a mobile device to the unit directly

(Wireless Direct) ..................................................... 19

Verify the network connection status .......................... 20

BASIC OPERATION

Playback .................................................................... 21

Playing a source........................................................... 21

Using the sleep timer ................................................... 23

Listening to FM/AM radio....................................... 24

FM/AM tuning............................................................. 24

Automatic preset tuning (FM stations only)................ 24

Manual tuning preset ................................................... 25

Recalling a preset station ............................................. 26

Clearing a preset station............................................... 26

Radio Data System tuning ........................................... 27

Playing back music via Bluetooth............................ 28

Connecting a Bluetooth device (pairing) ..................... 28

Playing back Bluetooth device contents ...................... 28

Disconnecting a Bluetooth connection ........................ 29

Playing back music stored on media servers

(PCs/NAS) ............................................................. 30

Setting the media sharing of music files...................... 30

Playback of PC music contents.................................... 31

Listening to Internet radio .......................................33

Playing back iPod/iTunes music via a network

(AirPlay).................................................................35

Playback of iPod/iTunes music contents ..................... 35

Playing back music stored on a USB storage

device ......................................................................37

Connecting a USB storage device ............................... 37

Playback of USB storage device contents ................... 37

Playing back iPod music...........................................39

Connecting an iPod...................................................... 39

Playback of iPod content ............................................. 39

Switching information on the front display ............41

Registering the current playback song/station

(Preset function) ....................................................42

Registering to a preset ................................................. 42

Recalling a preset......................................................... 42

ADVANCED OPERATION

Configuring playback settings for different

playback sources (Option menu) .........................43

Option menu items....................................................... 43

Configuring various functions (Setup menu) .........44

Setup menu items......................................................... 44

Network ....................................................................... 45

Bluetooth ..................................................................... 46

Max Volume ................................................................ 47

Initial Volume.............................................................. 47

AutoPowerStdby (Auto Power Standby)..................... 47

ECO Mode................................................................... 47

Configuring the system settings

(ADVANCED SETUP menu)...............................48

ADVANCED SETUP menu items .............................. 48

Changing the speaker impedance setting (SP IMP.) ... 48

Selecting the remote control ID (REMOTE ID).......... 48

Restoring the default settings (INIT)........................... 48

Updating the firmware (UPDATE) ............................. 49

Checking the firmware version (VERSION)............... 49

Updating the unit’s firmware via the network.......50

ADDITIONAL INFORMATION

Troubleshooting.........................................................51

Error indications on the front display.....................57

Trademarks ...............................................................58

Specifications .............................................................59

Index...........................................................................60

Contents

• “Note” indicates precautions for use of the unit and its feature limitations. y indicates supplementary explanations for better use.

• This manual explains operations using the supplied remote control.

• This manual describes all the “iPod” and “iPhone” as the “iPod”. “iPod” refers to “iPod” and “iPhone”, unless otherwise specified.

• In this manual, iOS and Android mobile devices are collectively referred to as “mobile devices”. The specific type of mobile

device is noted in explanations as needed.

2 En

INTRODUCTION

This unit is a network receiver compatible with a network source such as a media server and mobile device.

It supports playback from not only analog sources such as a CD player but also Bluetooth devices and network streaming

services.

*

You need a commercially available wireless router (access point) when you use a mobile device.

1 Play back the Internet radio (p. 33)

2 Play back the streaming service

(see the supplement for each service.)

3 Play back music files stored on your PC (p. 30)

4 Play back music files stored on your NAS

(p. 30)

5 Play back music files stored on your iPod/

iTunes with AirPlay (p. 35)

6 Play back audio content from Bluetooth

devices (p. 28)

7 Play back music files stored on your iPod

(p. 39)

8 Play back music files stored on your USB

device (p. 37)

9 Play back your external component (p. 11)

0 Listening to FM/AM radio (p. 24)

y

For details on connecting the external devices, see “Connections” (p. 11).

What you can do with this unit

Sources that can be played back on this unit

FM/AMFM/AM

VOLUME

PURE DIRECT

RETURN

CONNECT

PUSH - ENTER

TUNINGPRESET

BAND

MEMORY CLEAR

BASSINPUT

5V

1A

BALANCE

LR

TREBLE

LOUDNESS

FLAT

-30dB

DIMMER

DISPLAY

SELECT

PHONES

SPEAKERS

AB

MODE

This unit

1 Internet

2 Streaming service

Modem

Router*

3 PC

5 AirPlay (iTunes)

4 NAS

7 iPod

0

5 AirPlay (iPod)

6 Bluetooth

8 USB

device

9 CD player etc.

Mobile

device

What you can do with this unit

3 En

INTRODUCTION

English

You can operate and program the unit, or play streaming services via this unit, by installing the free dedicated MusicCast

CONTROLLER app on a mobile device. For details, search for “MusicCast CONTROLLER” on the App Store or

Google Play.

■ MusicCast CONTROLLER capabilities

• Basic operations of the unit (turn on/standby, adjust volume and select input)

• Play songs stored on computers (servers)

• Select an Internet radio station

• Play music stored on mobile devices

• Play music on streaming service

• Distribute and receive audio between the unit and other Yamaha MusicCast supported devices

See MusicCast Setup Guide for details.

Mastering useful apps (MusicCast CONTROLLER)

4 En

Check that the following accessories are supplied with the product.

Supplied accessories

LINE 1

OPT 1 OPT 2 CD

COAX 1 COAX 2

BLUETOOTH

NET USB

LINE 2 LINE 3

TUNER

PRESET

TUNING

BAND

MEMORY

SETUP

HOME

MUTENOW PLAYING

VOLUME

RETURN

ENTER

REPEAT

SHUFFLE

SLEEP

PHONO

B

A

SPEAKERS

OPTION

Remote control

FM antennaAM antenna

Batteries (x2)

(AA, R6, UM-3)

MusicCast Setup Guide

Controls and functions

5 En

INTRODUCTION

English

1 A (power)

Turns on/off (standby) the unit.

2 STANDBY/ON indicator

Lights up as follows:

Brightly lit: Power is on

Dimly lit: Standby mode

In standby mode, this unit consumes a small amount of power to

receive infrared signals from the remote control.

3 Remote control sensor

Receives infrared signals from the remote control.

4 DIMMER

Changes the brightness level of the front display. Choose

brightness from 5 levels by pressing this button

repeatedly.

5 DISPLAY

Selects the information displayed on the front display

(p. 41).

6 MODE

Sets the FM band reception mode to automatic stereo or

monaural (p. 24).

Switches the iPod operation modes (p. 40).

7 MEMORY

Registers the current FM/AM station as a preset when

TUNER is selected as the input source (p. 25).

Registers the current playback song or streaming station

as a preset when NET, USB (except iPod) are selected as

the input source (p. 42).

8 CLEAR

Clears a FM/AM preset station when TUNER is selected

as the input source (p. 26).

9 BAND

Switches between FM and AM (p. 24).

0 Front display

Shows information about the operational status of this

unit.

A PRESET j / i

Recalls a preset FM/AM station (p. 26) or song/streaming

station (p. 42).

B TUNING jj / ii

Selects the tuning frequency when TUNER is selected as

the input source (p. 24).

C PURE DIRECT and indicator

Allows you to listen to a source in the purest possible

sound (p. 21). The indicator above it lights up and the

front display turns off when this function is turned on.

Controls and functions

Front panel

VOLUME

PURE DIRECT

RETURN

CONNECT

PUSH - ENTER

TUNINGPRESET

BAND

MEMORY CLEAR

BASSINPUT

5V

1A

BALANCE

LR

TREBLE

LOUDNESS

FLAT

-30dB

DIMMER MODE

DISPLAY

SELECT

PHONES

SPEAKERS

AB

12 3 4 5 6 7 8 9: B CA

Note

Controls and functions

6 En

D PHONES jack

Outputs audio to your headphones for private listening.

E SPEAKERS A/B

Turns on or off the speaker set connected to the

SPEAKERS A and/or SPEAKERS B terminals on the rear

panel each time the corresponding button is pressed.

F USB jack

For connecting a USB storage device (p. 37) or an iPod

(p. 39).

G INPUT selector

Selects the input source you want to listen to.

H BASS +/– control

Increases or decreases the low frequency response. The

center position produces a flat response (p. 22).

I TREBLE +/– control

Increases or decreases the high frequency response. The

center position produces a flat response (p. 22).

J BALANCE control

Adjusts the sound output balance of the left and right

speakers to compensate for sound imbalances caused by

speaker locations or listening room conditions (p. 22).

K LOUDNESS control

Retains a full tonal range at any volume level to

compensate for the human ears’ loss of sensitivity to high

and low-frequency ranges at a low volume level (p. 22).

L SELECT/ENTER (jog dial)

Turn the dial to select a numeric value or setting, and press

the dial to confirm.

M RETURN

Returns to the previous indication of the front display.

CONNECT

Use to control the unit using the dedicated MusicCast

CONTROLLER app for mobile devices. See MusicCast

Setup Guide for details.

N VOLUME control

Increases or decreases the sound output level.

VOLUME

PURE DIRECT

RETURN

CONNECT

PUSH - ENTER

TUNINGPRESET

BAND

MEMORY CLEAR

BASSINPUT

5V

1A

BALANCE

LR

TREBLE

LOUDNESS

FLAT

-30dB

DIMMER MODE

DISPLAY

SELECT

PHONES

SPEAKERS

AB

NIHGED J KLMF

Controls and functions

7 En

INTRODUCTION

English

y

If the network connection is not set, turn the power ON to display “WAC” (Wireless Accessory Configuration) on the front panel and

trigger an automatic iOS device search. See “Sharing the iOS device setting” (p. 16) for details on the iOS device and network

connection.

1 Information display

Displays the current status (such as input name).

You can switch the information that is displayed when you

press DISPLAY on the front panel (p. 41).

2 STEREO

Lights up when the unit is receiving a stereo FM radio

signal.

3 TUNED

Lights up when the unit is receiving an FM/AM radio

station signal.

4 Signal strength indicator

Lights up when the unit connects to a wireless network or

operates as an access point. The strength of the wireless

network signal can be verified by the indicator status.

5 Bluetooth indicator

Lights up when the unit is connecting to a Bluetooth

device.

6 Speaker indicators

“A” lights up when the SPEAKERS A output is enabled

and “B” lights up when the SPEAKERS B output is

enabled.

7 SLEEP

Lights up when the sleep timer is on.

8 MUTE

Blinks when audio is muted.

9 Volume indicator

Indicates the current volume.

0 Cursor indicators

Indicate the remote control cursor keys currently

operational.

y

You can change the brightness level of the front display by

pressing DIMMER on the front panel (p. 5).

Front display

VOL.

MUTE

TUNEDSTEREO

A

SLEEP

B

1 9

6

: :

2

3 7 854

Controls and functions

8 En

1 PHONO jacks

For connecting to a turntable (p. 11).

2 OPTICAL 1/2 jacks

For connecting to audio components equipped with

optical digital output (p. 11).

3 ANTENNA terminals

For connecting to FM and AM antennas (p. 13).

4 COAXIAL 1/2 jacks

For connecting to audio components equipped with a

coaxial digital output (p. 11).

5 SPEAKERS terminals

Used to connect speakers (p. 12).

6 NETWORK jack

For connecting to a network with a network cable (p. 14).

7 Wireless antenna

For connecting to a network device wirelessly (p. 14).

8 Power cable

For connecting to an AC wall outlet (p. 14).

9 LINE 1-3 jacks

For connecting to analog audio components (

p. 11

).

0 CD jacks

For connecting to a CD player (p. 11).

A SUBWOOFER PRE OUT jack

For connecting to a subwoofer with built-in amplifier

(p. 11).

Rear panel

A

B

SPEAKERS

NETWORK

COAXIAL

OPTICAL

FM AM

75Ω

ANTENNA

SUBWOOFER

PRE OUT

PHONO

IN

1

IN

OUT

2

1

2

1

2

IN

CD

LINE

OUT

3

SIGNAL

GND

3 5 68

A

1 2 4 7

9 :

Controls and functions

9 En

INTRODUCTION

English

1 Infrared signal transmitter

Sends infrared signals.

2 SPEAKERS A/B

Turns on and off the set of speakers connected to the SPEAKERS

A and/or SPEAKERS B terminals on the rear panel of this unit

when the corresponding key is pressed.

3 Input selection keys

Select an input source for playback.

PHONO PHONO jacks

COAX 1/2 COAXIAL1/2 jacks

BLUETOOTH Bluetooth connection

OPT 1/2 OPTICAL 1/2 jacks

CD CD jacks

LINE 1-3 LINE 1-3 jacks

TUNER FM/AM tuner

NET Network source (press repeatedly to select a

desired network source)

USB USB jack (on the front panel)

4 Radio keys

Operate the FM/AM radio (p. 24).

BAND Switches between FM and AM.

TUNING jj/ii Selects the radio frequency.

5 Preset keys

MEMORY Registers the current FM/AM station as a

preset when TUNER is selected as the input

source (p. 25).

Registers the current playback song or

streaming station as a preset when NET, USB

(except iPod) are selected as the input source

(p. 42).

PRESET j/i Recalls a preset FM/AM station (p. 26) or

song/streaming station (p. 42).

6 Menu operation keys

Cursor keys Select a menu or a parameter.

(B/C/D/E)

ENTER Confirms a selected item.

RETURN Returns to the previous state.

7 HOME

Moves up top level when selecting music files, folders, etc.

8 SETUP

Displays the “Setup” menu (p. 44).

9 NOW PLAYING

Displays music information when selecting music files, folders,

etc.

0 VOLUME +/-

Adjust the volume.

A Playback keys

Let you play back and perform other operations for network

sources, Bluetooth devices and USB devices.

Remote control

LINE 1

OPT 1 OPT 2 CD

COAX 1 COAX 2

BLUETOOTH

NET USB

LINE 2 LINE 3

TUNER

PRESET

TUNING

BAND

MEMORY

SETUP

HOME

MUTENOW PLAYING

VOLUME

RETURN

ENTER

REPEAT

SHUFFLE

SLEEP

PHONO

B

A

SPEAKERS

OPTION

1

3

6

7

0

8

9

2

4

5

A

Controls and functions

10 En

B A (power)

Turns on/off (standby) the unit.

C SLEEP

Sets the sleep timer (p. 23).

D OPTION

Displays the “Option” menu (p. 43).

E MUTE

Mutes the audio output.

■ Installing batteries

• Change all batteries if the operation range of the remote control

narrows.

• Before inserting new batteries, wipe the compartment clean.

■ Operation range

The remote controls transmit a directional infrared beam.

Be sure to aim the remote controls directly at the remote

control sensor on the front panel of this unit.

LINE 1

OPT 1 OPT 2 CD

COAX 1 COAX 2

BLUETOOTH

NET USB

LINE 2 LINE 3

TUNER

PRESET

TUNING

BAND

MEMORY

SETUP

HOME

MUTENOW PLAYING

VOLUME

RETURN

ENTER

REPEAT

SHUFFLE

SLEEP

PHONO

B

A

SPEAKERS

OPTION

B

C

D

E

Notes

30° 30°

Remote control

Approximately

6 m (20 ft)

11 En

PREPARATION

English

PREPARATION

• Do not connect this unit or other components to the main power until all connections between components are complete.

• All connections must be correct: L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty,

no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be

unnatural and lack bass. Refer to the owner’s manual for each of your components.

• Do not let bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or the speakers.

• Make sure to use RCA cables, optical cables to connect audio components.

y

• The PHONO jacks are designed for connecting a turntable with an MM cartridge.

• Connect your turntable to the GND terminal to reduce noise in the signal. However, for some turntables, you may hear less noise

without the GND connection.

• In order to prevent the audio signal from looping when an audio recording device is connected, the audio signal is not output from the

LINE 2 (OUT) jacks when LINE 2 is selected. Similarly, the audio signal is not output from the LINE 3 (OUT) jacks when LINE 3 is

selected.

• Do not bundle audio cables and speaker cables together with the power cable. Doing so may generate noise.

Connections

CAUTION

Only PCM signals can be input to the digital (OPTICAL/COAXIAL) jacks of this unit.

Notes

A

B

SPEAKERS

NETWORK

COAXIAL

OPTICAL

FM AM

75Ω

ANTENNA

SUBWOOFER

PRE OUT

PHONO

IN

1

IN

OUT

2

1

2

1

2

IN

CD

LINE

OUT

3

SIGNAL

GND

O C

Audio

input

Audio

output

Speakers B

Turntable

Audio

output

DVD player, etc.

GND

Audio output

(digital coaxial)

Audio output

(digital optical)

CD player, etc.

Audio

output

CD player

Subwoofer

CD recorder, etc.

Speakers A

12 En

Connections

■ Connecting speaker cables

Speaker cables have two wires. One is for connecting the

negative (–) terminal of the unit and the speaker, and the

other is for the positive (+) terminal. If the wires are

colored to prevent confusion, connect the black wire to the

negative and the other wire to the positive terminal.

a

Remove approximately 10 mm (3/8”) of insulation from the ends of

the speaker cable and twist the bare wires of the cable firmly together.

b Loosen the speaker terminal.

c Insert the bare wires of the cable into the gap on the side (upper

right or bottom left) of the terminal.

d Tighten the terminal.

■ Bi-wire connection

Bi-wire connection separates the woofer from the

combined midrange and tweeter section. A bi-wire

compatible speaker has four binding post terminals. These

two sets of terminals allow the speaker to be split into two

independent sections. With these connections, the mid and

high frequency drivers are connected to one set of terminals

and the low frequency driver to another set of terminals.

Connect the other speaker to the other set of terminals in

the same way.

When making bi-wire connections, remove the shorting bridges

or cables on the speaker. Refer to the speakers’ instruction

manuals for more information.

y

To use the bi-wire connections, press SPEAKERS A and

SPEAKERS B on the front panel or on the remote control so that

both speaker indicators (“A” and “B”) light up on the front

display.

Connecting the speakers

aa

b

d

c

10 mm

(3/8")

Note

A

B

SPEAK

This unit

Speaker

VOLUME

PURE DIRECT

RETURN

CONNECT

PUSH - ENTER

TUNINGPRESET

BAND

MEMORY CLEAR

BASSINPUT

5V

1A

BALANCE

LR

TREBLE

LOUDNESS

FLAT

-30dB

DIMMER MODE

DISPLAY

SELECT

PHONES

SPEAKERS

AB

SPEAKERS A/B

OPT 1 OPT 2 CD

COAX 1 COAX 2

BLUETOOTH

SLEEP

PHONO

B

A

SPEAKERS

SPEAKERS A/B

13 En

Connections

PREPARATION

English

The antennas for receiving FM and AM broadcasts are included with this unit. In general, these antennas should provide

sufficient signal strength. Connect each antenna correctly to the designated terminals.

If you experience poor reception quality, install an outdoor antenna. Consult the nearest authorized Yamaha dealer or service center

about outdoor antennas.

■ Assembling the supplied AM antenna ■ Connecting the wires of the AM antenna

Connecting the FM and AM antennas

Note

COAXIAL

OPTICAL

FM AM

75Ω

ANTENNA

SUBWOOFER

PRE OUT

PHONO

IN

1

IN

OUT

2

1

2

1

2

IN

CD

LINE

OUT

3

SIGNAL

GND

FM antenna

(included)

Outdoor AM antenna

Use 5 to 10 m of vinyl-covered wire extended

outdoors from a window.

Outdoor

FM antenna

• The AM antenna should always be connected, even if an outdoor

AM antenna is connected to this unit.

• The AM antenna should be placed away from this unit.

AM antenna (included)

or

Insert

2

Hold down

1

14 En

Connections

Connect the unit to your router with a commercially-available STP network cable (CAT-5 or higher straight cable).

If you connect the unit wirelessly, erect the wireless

antenna. For information on how to connect the unit to a

wireless network, see “Connecting to network” (p. 15).

Do not apply excessive force on the wireless antenna. Doing so

may damage the antenna.

After all the connections are complete, plug in the power

cable.

Connecting the network cable

A

B

SPEAKERS

NETWORK

COAXIAL

OPTICAL

FM AM

75Ω

ANTENNA

SUBWOOFER

PRE OUT

PHONO

IN

1

IN

OUT

2

1

2

1

2

IN

CD

LINE

OUT

3

SIGNAL

GND

LAN

WAN

Network Attached Storage

(NAS)

Internet

Modem

Router

Network cable

PC

This unit (rear)

Mobile device

(such as iPhone)

Preparing a wireless antenna

Note

WIRELES

S

WORK

Connecting power cable

To an AC wall outlet

Connecting to network

15 En

PREPARATION

English

There are several methods to connect the unit to a network. Select a connection method according to your environment.

• Some security software installed on your PC or the firewall settings of network devices (such as a router) may block the access of the

unit to the network devices or the Internet. In these cases, configure the security software or firewall settings appropriately.

• Each server must be connected to the same subnet as the unit.

• To use the service via the Internet, broadband connection is strongly recommended.

■ Connecting with the MusicCast CONTROLLER app

See MusicCast Setup Guide for details.

■ Connecting with the wired router

■ Connecting with a wireless router (access point)

Connect to the network with the method listed below that corresponds to your environment.

■ Connecting without a wired router or wireless router (access point)

When the unit is connected to the network with Wireless Direct, it cannot connect to any other wireless router (access point). To play

back contents from the Internet, connect this unit to a network with a wired router or wireless router (access point).

Connecting to network

Notes

When playing a high-resolution audio source via the network, we recommend connecting with a wired router for stable playback.

Note

Connecting using the DHCP server function of the

router

You can connect to the network by

simply making a wired connection

(p. 14)

Connecting using the Wi-Fi setting of the iOS

device (iPhone / iPod touch)

Share the Wi-Fi setting of the iOS

device (p. 16)

Connecting using WPS push button configuration

on the wireless router (or access point)

Use the WPS push button

configuration (p. 17)

Connecting with a wireless router (access point)

without WPS push button configuration

Set the network connection

manually (p. 18)

Connecting wirelessly to a mobile device

(Wireless Direct)

Connect wirelessly with Wireless

Direct (p. 19)

16 En

Connecting to network

You can easily setup a wireless connection by applying the

connection settings on iOS devices (iPhone/iPod touch).

Before proceeding, confirm that your iOS device is

connected to a wireless router (access point).

1 Press A to turn on this unit.

2 Press SETUP.

3 Use the cursor keys (B / C) to select

“Network” and press ENTER.

y

To return to the previous state, press RETURN.

4 Use the cursor keys (B / C) to select

“Connection” and press ENTER.

5 Use the cursor keys (B / C) to select

“Wireless” and press ENTER.

6 Use the cursor keys (B / C) to select “Share

Setting” and press ENTER.

7 Use the cursor keys (B / C) to select the

desired connection method and press

ENTER.

The following connection methods are available.

When you select “Wireless (WAC)” as the connection method, all

network settings are initialized.

■ Sharing the iOS device setting wirelessly

If you select “Wireless (WAC)” as the connection method,

perform the network setting sharing operation on your iOS

device. (The following procedure is a setup example for

iOS 8.)

1 On the iOS device, select the unit as the

AirPlay speaker in the Wi-Fi screen.

2 Check the network currently selected and tap

“Next”.

When the sharing process finishes, the unit is

automatically connected to the selected network

(access point).

When the setting finishes, verify whether the unit is

connected to a wireless network (p. 20).

Sharing the iOS device setting

If the network connection is not set, when you turn on

this unit, “WAC” (Wireless Accessory Configuration)

appears on the front display, and the iOS device setting

can be shared.

To share the iOS device setting, perform the network

setting sharing operation on your iOS device.

R-N602 XXXXXX

WAC

PRESET

MEMORY

SETUP

HOME

MUTENOW PLAYING

VOLUME

RETURN

ENTER

OPTION

RETURN

SETUP

ENTER

Cursor keys

B

/

C

WPS

WIRELESS

Wireless(WAC)

SHARE

Wireless

(WAC)

You can apply the connection settings on the iOS

device to the unit using a wireless connection. For

details, see “Sharing the iOS device setting

wirelessly”. (You need iOS device with iOS 7 or

later.)

USB

Cable

You can apply the connection settings on the iOS

device to the unit using a USB cable. For details, see

“Sharing the iOS device setting using a USB cable”.

(You need iOS device with iOS 5 or later.)

Note

The name of this unit

Tap here to start setup

The network currently

selected

Страница загружается...

Yamaha R-N602 Инструкция по применению

Похожие модели бренда