Generac XG5600E G0062200 Руководство пользователя

  • Привет! Я прочитал руководство пользователя для портативного генератора Generac XG серии. Готов ответить на ваши вопросы о его характеристиках, эксплуатации и техническом обслуживании. В руководстве подробно описаны способы запуска, подключения нагрузок, профилактические меры и меры безопасности.
  • Где можно использовать этот генератор?
    Как часто нужно менять масло?
    Что делать, если генератор перегружен?
    Как запустить генератор?
www.generac.com
Owner's Manual
XG Series 5,600-6,400 Watt, 50 Hz Portable Generator

DEADLY EXHAUST FUMES! ONLY use OUTSIDE
far away from windows, doors and vents!
NOT INTENDED FOR USE IN CRITICAL LIFE
SUPPORT APPLICATIONS.

SAVE this Manual. Provide this manual to any
operator of the generator.
Introduction ............................................................. 1
Read this Manual Thoroughly ................................. 1
Safety Rules ........................................................... 1
Registration ............................................................ 3
General Information ................................................ 4
1.1 Unpacking ......................................................................4
1.1.1 Accessory Box ..................................................4
1.2 Assembly .......................................................................4
1.2.1 Assembling the Wheel Kit and Frame Foot ..........4
Operation ................................................................ 5
2.1 Know the Generator .......................................................5
2.1.1 Battery Connection ............................................6
2.2 Hourmeter ......................................................................6
2.3 Cord Sets and Connection Plugs ....................................6
2.3.1 230 VAC, 16 Amp, CEE 7/4, Type F Receptacle .6
2.3.2 230 VAC, 30 Amp Receptacle ............................7
2.3.3 Adapter Cable, 50 Hz (XG5600/XG6400 only) ....7
2.4 How to Use the Generator ..............................................7
2.4.1 System Ground ..................................................8
2.4.2 Connecting to a Building's Electrical System ......8
2.4.3 Connecting Electrical Loads ...............................8
2.5 Don’t Overload the Generator ..........................................8
2.6 Before Starting the Generator .........................................8
2.6.1 Adding Engine Oil ..............................................8
2.6.2 Adding Gasoline .................................................9
2.7 To Start the Engine .........................................................9
2.7.1 Manual (Recoil) Starting ..................................10
2.7.2 Electric Starting ...............................................10
2.8 Stopping the Engine .....................................................10
2.9 Low Oil Pressure Shutdown System .............................10
2.9.1 Restarting ........................................................10
2.10 Charging the Battery (Electric Start Units Only) .............10
Maintenance ......................................................... 11
3.1 Maintenance Schedule .................................................11
3.2 Product Specifications ..................................................11
3.2.1 Generator Specifications ..................................11
3.2.2 Engine Specifications .......................................11
3.3 General Recommendations ...........................................11
3.3.1 Generator Maintenance ....................................11
3.3.2 To Clean the Generator .....................................12
3.3.3 Engine Maintenance .........................................12
3.3.4 Checking Oil Level ...........................................12
3.3.5 Changing the Oil and Oil Filter ..........................12
3.3.6 Replacing the Spark Plug .................................12
3.4 Service Air Filter ...........................................................12
3.5 Clean Spark Arrestor Screen.........................................13
3.6 General ........................................................................13
3.7 Long Term Storage .......................................................13
3.8 Other Storage Tips .......................................................13
Battery Service ..................................................... 14
4.1 Battery Replacement ....................................................14
Troubleshooting .................................................... 15
5.1 Troubleshooting Guide ..................................................15
Warranty ................................................. Back Cover
Table of Contents
1
INTRODUCTION
Thank you for purchasing this model by Generac Power Systems,
Inc. This model is a compact, high performance, air-cooled,
engine driven generator designed to supply electrical power to
operate electrical loads where no utility power is available or in
place of utility due to a power outage.
READ THIS MANUAL THOROUGHLY
If any portion of this manual is not understood, contact the
nearest Authorized Dealer for starting, operating and servicing
procedures.
The operator is responsible for proper and safe use of the
equipment. We strongly recommend that the operator read this
manual and thoroughly understand all instructions before using the
equipment. We also strongly recommend instructing other users to
properly start and operate the unit. This prepares them if they need
to operate the equipment in an emergency.
The generator can operate safely, efficiently and reliably only if it
is properly located, operated and maintained. Before operating or
servicing the generator:
Become familiar with and strictly adhere to all local, state and
national codes and regulations.
Study all safety warnings in this manual and on the product
carefully.
Become familiar with this manual and the unit before use.
The manufacturer cannot anticipate every possible circumstance
that might involve a hazard. The warnings in this manual, and on
tags and decals affixed to the unit are, therefore, not all inclusive.
If using a procedure, work method or operating technique that the
manufacturer does not specifically recommend, ensure that it is
safe for others. Also make sure the procedure, work method or
operating technique utilized does not render the generator unsafe.
THE INFORMATION CONTAINED HEREIN WAS BASED ON
MACHINES IN PRODUCTION AT THE TIME OF PUBLICATION.
GENERAC RESERVES THE RIGHT TO MODIFY THIS MANUAL AT
ANY TIME.
SAFETY RULES
Throughout this publication, and on tags and decals affixed to the
generator, DANGER, WARNING, CAUTION and NOTE blocks are
used to alert personnel to special instructions about a particular
operation that may be hazardous if performed incorrectly or
carelessly. Observe them carefully. Their definitions are as
follows:
INDICATES A HAZARDOUS SITUATION OR ACTION WHICH, IF
NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.
Indicates a hazardous situation or action which, if not
avoided, could result in death or serious injury.
Indicates a hazardous situation or action which, if not
avoided, could result in minor or moderate injury.
NOTE:
Notes contain additional information important to a procedure
and will be found within the regular text body of this manual.
These safety warnings cannot eliminate the hazards that they
indicate. Common sense and strict compliance with the special
instructions while performing the action or service are essential to
preventing accidents.
Four commonly used safety symbols accompany the DANGER,
WARNING and CAUTION blocks. The type of information each
indicates is as follows:

This symbol points out important safety
information that, if not followed, could
endanger personal safety and/or property of
others.
This symbol points out potential explosion
hazard.
This symbol points out potential fire hazard.

This symbol points out potential electrical
shock hazard.
GENERAL HAZARDS
NEVER operate in an enclosed area, in a vehicle, or indoors
EVEN IF doors and windows are open.
• For safety reasons, the manufacturer recommends that the
maintenance of this equipment is carried out by an Authorized
Dealer. Inspect the generator regularly, and contact the nearest
Authorized Dealer for parts needing repair or replacement.
Operate generator only on level surfaces and where it will not be
exposed to excessive moisture, dirt, dust or corrosive vapors.
Keep hands, feet, clothing, etc., away from drive belts, fans,
and other moving parts. Never remove any fan guard or shield
while the unit is operating.
Certain parts of the generator get extremely hot during
operation. Keep clear of the generator until it has cooled to
avoid severe burns.
Do NOT operate generator in the rain.
• Do not alter the construction of the generator or change
controls which might create an unsafe operating condition.
Never start or stop the unit with electrical loads connected
to receptacles AND with connected devices turned ON. Start
the engine and let it stabilize before connecting electrical
loads. Disconnect all electrical loads before shutting down the
generator.
Do not insert objects through unit’s cooling slots.
When working on this equipment, remain alert at all times.
Never work on the equipment when physically or mentally
fatigued.
Introduction
2
Never use the generator or any of its parts as a step. Stepping
on the unit can stress and break parts, and may result in
dangerous operating conditions from leaking exhaust gases,
fuel leakage, oil leakage, etc.
On electric start models, disconnect the POSITIVE (+) battery
cable from the engine starter OR the NEGATIVE (-) battery
cable from the battery terminal, whichever is easier, before
transporting the generator.
NOTE:
This generator is equipped with a spark arrestor muffler.
The spark arrestor must be maintained in effective working
order by the owner/ operator. See the "Clean Spark Arrestor
Screen" section.
EXHAUST & LOCATION HAZARDS
Never operate in an enclosed area or indoors! NEVER use in
the home, in a vehicle, or in partly enclosed areas such as
garages, EVEN IF doors and windows are open! ONLY use
outdoors and far from open windows, doors, vents, and in an
area that will not accumulate deadly exhaust.
The engine exhaust fumes contain carbon monoxide, which
you cannot see or smell. This poisonous gas, if breathed in
sufficient concentrations, can cause unconsciousness or even
death.
Adequate, unobstructed flow of cooling and ventilating air
is critical to correct generator operation. Do not alter the
installation or permit even partial blockage of ventilation
provisions, as this can seriously affect safe operation of the
generator. The generator MUST be operated outdoors.
This exhaust system must be properly maintained. Do nothing
that might render the exhaust system unsafe or in noncompliance
with any local codes and/or standards.
• Always use a battery operated carbon monoxide alarm indoors,
installed according to the manufacturers instructions.
If you start to feel sick, dizzy, or weak after the generator has
been running, move to fresh air IMMEDIATELY. See a doctor, as
you could have carbon monoxide poisoning.
ELECTRICAL HAZARDS
The generator produces dangerously high voltage when in
operation. Avoid contact with bare wires, terminals, connections,
etc., while the unit is running, even on equipment connected
to the generator. Ensure all appropriate covers, guards and
barriers are in place before operating the generator.
Never handle any kind of electrical cord or device while
standing in water, while barefoot or while hands or feet are wet.
DANGEROUS ELECTRICAL SHOCK MAY RESULT.
Local electrical codes may require proper grounding of the
generator. Consult with a local electrician for grounding
requirements in the area.
Do not use worn, bare, frayed or otherwise damaged electrical
cord sets with the generator.
Before performing any maintenance on the generator,
disconnect the engine starting battery to prevent accidental
start up. Disconnect the cable from the battery post indicated
by a NEGATIVE, NEG or (–) first. Reconnect that cable last.
In case of accident caused by electric shock, immediately shut
down the source of electrical power. If this is not possible,
attempt to free the victim from the live conductor. AVOID
DIRECT CONTACT WITH THE VICTIM. Use a non-conducting
implement, such as a rope or board, to free the victim from the
live conductor. If the victim is unconscious, apply first aid and
get immediate medical help.
FIRE HAZARDS
Gasoline is highly FLAMMABLE and its vapors are EXPLOSIVE.
Do not permit smoking, open flames, sparks or heat in the
vicinity while handling gasoline.
• Never add fuel while unit is running or hot. Allow engine to cool
completely before adding fuel.
Never fill fuel tank indoors. Comply with all laws regulating
storage and handling of gasoline.
Do not overfill the fuel tank. Always allow room for fuel
expansion. If tank is over-filled, fuel can overflow onto a hot
engine and cause FIRE or an EXPLOSION. Never store generator
with fuel in tank where gasoline vapors might reach an open
flame, spark or pilot light (as on a furnace, water heater or
clothes dryer). FIRE or EXPLOSION may result. Allow unit to
cool entirely before storage.
• Wipe up any fuel or oil spills immediately. Ensure that no
combustible materials are left on or near the generator. Keep the
area surrounding the generator clean and free from debris and
keep a clearance of five (5) feet on all side to allow for proper
ventilation of the generator.
Do not insert objects through unit’s cooling slots.
• Do not operate the generator if connected electrical devices
overheat, if electrical output is lost, if engine or generator sparks
or if flames or smoke are observed while unit is running.
Keep a fire extinguisher near the generator at all times.
Safety Rules
3
REGISTRATION
Register your product online at www.generac.com to receive
important product information or updates.
MODEL NO:
SERIAL NO:
Generator Identification
Safety Rules
4
1.1 UNPACKING
Remove all packaging material.
Remove separate accessory box.
Remove carton off the generator.
1.1.1 ACCESSORY BOX
Check all contents (Figure 1). If any parts are missing or damaged
locate an authorized dealer at www.generac.com/Dealer Locator.
Contents include:
• 1-Owner’s manual
• 1-Frame Foot
• 2-Wheels
1-Hardware bag (containing the following):
– 5-Flange Nuts
– 2-Rubber Feet
– 2-Short Bolts
– 2-Cotter Pins
• 1-Axle
1-Handle with Grip
• 1-Plastic Spacer
• 1-Handle Bracket
• 3-Long Bolts
• 1-Handle Assembly
2-Long Curved Head Bolts
• 2-Acorn Nuts
• 2-Axle Pins
• 2-Washers
2-Flange Nuts (electric start only)
1-Battery Charger (electric start only)
1- Adapter Cable (see the "Adapter Cable, 50 Hz" section)
Figure 1 – Accessory Boxes
1.2 ASSEMBLY
Read entire Owner's Manual before attempting to assemble or
operate the generator. The generator requires some assembly
prior to using it. If problems arise when assembling the generator,
please call an authorized dealer at www.generac.com/Dealer
Locator.
1.2.1 ASSEMBLING THE WHEEL KIT AND FRAME FOOT
The wheel kit is designed to greatly improve the portability of the
generator. Refer to Figure 2 and install the wheel kit and frame foot
as follows.
You will need the following tools to install the wheel kit:
• Pliers
• 13mm wrench
13mm socket wrench
NOTE:
The wheel kit is not intended for over-the-road use.
Wheels
Slide the Axle Pin through the Wheel, Wheel Spacer (Washer)
and the Frame.
Install the Hair Pin to the Axle Pin to secure the wheel. Repeat
for the opposite side.
Foot
Secure the Vibration Mounts to the Frame Foot with the included
locking nuts.
To install the Frame Foot, install the Frame Bolts though the
Frame Washers, Frame and Frame foot. Secure with the flange
nuts.
Figure 2 – Wheel and Foot Assembly
General Information
5
2.1 KNOW THE GENERATOR
Read the entire Owner’s Manual and Safety Rules before
operating this generator.
Compare the generator to Figures 3 through 6 to become
familiarized with the locations of various controls and adjustments.
Save this manual for future reference.
1. Choke Knob – Used when starting a cold engine (Pull/Push).
2. Engine Switch – Controls the operation of the generator. The
switch is Start/Run/Stop.
3. Fuel Shut Off – Valve between fuel tank and carburetor. Turn
off and run carburetor out of fuel for extended storage.
4. Panel LED's – Provide illumination of the control panel while
the generator is operating.
5. 230 Volt AC, 30 Amp Locking Receptacle – Supplies
electrical power for the operation of 230 Volt AC, 30 Amp or
25 Amp, single-phase, 50 Hz, electrical lighting, appliances,
tools and motor loads.
6. 230 Volt AC, 16 Amp, CEE 7/4, Type F Receptacle – Supplies
electrical power for the operation of 230 Volt AC, 16 Amp,
single-phase, 50 Hz electrical lighting, appliances, tools and
motor loads.
7. Circuit Breakers (AC) – Each 16 Amp receptacle is provided
with a push-to-reset circuit breaker of the same rating to
protect the generator against electrical overload.
8. Circuit Breakers (AC) – The 30 Amp receptacle is protected
with a push-to-reset circuit breaker of the same rating to
protect the generator against electrical overload.
9. PowerBar – Indicates the amount of power being used from
the generator; each section is approximately 25%.
10. Hourmeter – Provides operating hours for Service Intervals.
11. Battery Charger Input – This receptacle allows the capability
to recharge the 12 VDC engine starting battery with the 12 Volt
Adaptor Plug Charger. The battery is protected by a 1.50 Amp
in-line fuse which is inside the control panel.
12. Fuel Tank – See generator specifications for tank capacity.
13. Fuel Gauge – Shows fuel level in tank.
14. Handles – Pivot and retract for storage. Press the spring-
loaded button to move handles.
15. Oil Fill – Check oil level and add oil here.
16. Grounding Lug – Ground the generator to an approved earth
ground here. See "Grounding the Generator" for details.
17. Muffler – Includes the spark arrestor and quiets the engine.
18. Spark Plug Location – The spark plug ignites the Air/Fuel
Mixture (Side panel must be removed).
19. Engine Oil Filter – Filters engine oil; see Section 3.1 for the
proper service intervals.
20. Air Filter – Filters intake air as it is drawn into the engine.
21. Oil Drain – Drain valve to remove used oil from the engine
crankcase.
22. Recoil Starter – Use to start engine manually.
Figure 3 – Generator Locations
Operation
6
2.1.1 BATTERY CONNECTION
NOTE:
The battery shipped with the generator has been fully charged.
A battery may lose some of its charge when not in use for
prolonged periods of time. If the battery is unable to crank
the engine, plug in the 12V charger included in the accessory
box (see the Charging the Battery section). RUNNING THE
GENERATOR DOES NOT CHARGE THE BATTERY.
The positive battery wire was deliberately left detached for
shipping. To operate the unit, attach this wire to the terminal on
the starter motor as shown. Do not overtighten. Slide the attached
rubber boot over the starter terminal. See Figure 4.
Figure 4 – Battery Connection
2.2 HOURMETER
The Hourmeter tracks hours of operation for scheduled maintenance
(see chart) (Figure 5).
Operation: Push and release the reset button to toggle between
screens. The hours count backwards from the set interval as
shown in the chart.
When the meter reaches 5 hours,the text "CHG OIL" (or "SVC AIR
FILTER" or "CHG PLUG") will flash continually for two minutes.
After this time, the meter will go back to displaying the total hours
of the unit (for 2 minutes). This cyle will repeat for the entire 5
hours.
When the service interval reaches zero hours, the text "NOW"
replaces the hours remaining.
For a new generator for instance, the message will say "CHG OIL"
then flash "in 30". This means that in 30 hours, the oil will need to
be changed. Pressing the button a few more times will bring the
meter back to the screen that shows the total hours run.
Reset: Toggle to the alert that you wish to reset then hold the
button down for 9 seconds. The maintenance hours are reset when
the display shows "0000.0".
Note:
The hour glass graphic will flash on and off when the engine
is running. This signifies that the meter is tracking hours of
operation.
Figure 5 – Hourmeter
HOUR GLASS
GRAPHIC
RESET BUTTON
(IF EQUIPPED)
0000.0
2.3 CORD SETS AND CONNECTION PLUGS
2.3.1 230 VAC 16A, CEE 7/4, TYPE F RECEPTACLE
This is a 230 Volt outlet (Figure 6) protected against overload by
a 16 Amp push-to-reset circuit breaker. Use each socket to power
230 Volt AC, single phase, 50 Hz electrical loads requiring up to a
combined 3680 watts (3.7 kW) or 16 Amps of current. Use only
high quality, well-insulated, 3-wire grounded cord sets rated for
230 Volts at 16 Amps (or greater).
Keep extension cords as short as possible, preferably less than
5 meters long, to prevent voltage drop and possible overheating
of wires.
Operation
Hourmeter Chart
Message Frequency of Message Interval Duration of message
CHG OIL Initial break-in period First 30 Hours
ON/OFF for 2 minutes in a 5
hour period
CHG OIL Re-occuring 100 hours
SVC AIR FILTER Re-occuring 200 hours
CHG PLUG Re-occuring 200 hours
7
2.3.2 230 VAC, 30 AMP RECEPTACLE
Use this receptacle (rotate to lock/unlock) to operate 230 Volt AC,
50 Hz, single phase loads requiring up to 5600 watts (5.6 kW), or
6400 watts (6.4 kW), of power depending on the model. The outlet
is protected by a 25 or 30 Amp circuit breaker.
Figure 6 – Generator Receptacles
2.3.3 ADAPTPER CABLE, 50 HZ (XG5600/XG6400 ONLY)
Included with this generator is an adapter cable that plugs into the
30 Amp Twistlock receptacle on the generator control panel on one
end, and provides a 32 Amp IP44 CEE 2P+E socket on the other
end (Figure 7).
Figure 7 – Adapter Cable
2.4 HOW TO USE THE GENERATOR
If there are any problems operating the generator, please call the
authorized dealer at www.generac.com/Dealer Locator.

Never operate in an enclosed area or indoors!
NEVER use in the home, in a vehicle, or in
partly enclosed areas such as garages, EVEN
IF doors and windows are open! ONLY use
outdoors and far from open windows, doors,
vents, and in an area that will not accumulate
deadly exhaust.

The engine exhaust fumes contain carbon
monoxide, which you cannot see or smell.
This poisonous gas, if breathed in sufficient
concentrations, can cause unconsciousness or
even death.

Adequate, unobstructed flow of cooling and
ventilating air is critical to correct generator
operation. Do not alter the installation or permit
even partial blockage of ventilation provisions,
as this can seriously affect safe operation
of the generator. The generator MUST be
operated outdoors.

This exhaust system must be properly
maintained. Do nothing that might render the
exhaust system unsafe or in noncompliance
with any local codes and/or standards.

The manufacturer recommends installing
a battery operated carbon monoxide alarm
indoors, according to the manufacturers
instructions.
Operation
8
2.4.1 SYSTEM GROUND
The generator has a system ground that connects the generator
frame components to the ground terminals on the AC output
receptacles.
Special Requirements
There may be federal, state, safety or health administration
regulations, local codes, or ordinances that apply to the intended
use of the generator.
Please consult a qualified electrician, electrical inspector, or the
local agency having jurisdiction:
In some areas, generators are required to be registered with
local utility companies.
If the generator is used at a construction site, there may be
additional regulations which must be observed.
2.4.2 CONNECTING TO A BUILDING’S ELECTRICAL
SYSTEM
Connections for standby power to a building’s electrical system
must be made by a qualified electrician. The connection must
isolate the generator power from utility power or other alternative
power sources and must comply with all applicable laws and
electrical codes.
Grounding The Generator
Local electrical codes may require proper grounding of the unit
(Figure 8). For that purpose, connecting a 2.59mm stranded
copper wire to the grounding lug and to an earth-driven copper
or brass grounding rod (electrode) provides adequate protection
against electrical shock. However, local codes may vary widely.
Consult with a local electrician for grounding requirements in
the area.
Figure 8 – Generator Ground Location
2.4.3 CONNECTING ELECTRICAL LOADS
DO NOT connect 120 Volt loads to 230 Volt receptacles.
DO NOT connect 3 phase loads to the generator.
DO NOT connect 60 Hz loads to the generator.
• Let engine stabilize and warm up for a few minutes after
starting.
Plug in and turn on the desired 230 Volt AC, single phase, 50
Hz electrical loads.
Add up the rated watts (or amps) of all loads to be connected
at one time. This total should no be greater than (a) the rated
wattage/amperage capacity of the generator or (b) circuit
breaker rating of the receptacle supplying the power. See “Don’t
Overload the Generator
2.5 DON’T OVERLOAD THE GENERATOR
Overloading a generator in excess of its rated wattage capacity
can result in damage to the generator and to connected electrical
devices. Observe the following to prevent overloading the unit:
Add up the total wattage of all electrical devices to be connected
at one time. This total should NOT be greater than the
generator's wattage capacity.
The rated wattage of lights can be taken from light bulbs. The
rated wattage of tools, appliances and motors can usually be
found on a data label or decal affixed to the device.
If the appliance, tool or motor does not give wattage, multiply
volts times ampere rating to determine watts (volts x amps =
watts).
Some electric motors, such as induction types, require about
three times more watts of power for starting than for running.
This surge of power lasts only a few seconds when starting
such motors. Make sure to allow for high starting wattage when
selecting electrical devices to connect to the generator:
1. Figure the watts needed to start the largest motor.
2. Add to that figure the running watts of all other connected
loads.
2.6 BEFORE STARTING THE GENERATOR
Prior to operating the generator, engine oil and gasoline will need
to be added, as follows:
2.6.1 ADDING ENGINE OIL
Use no special additives. Select the oil's viscosity grade according
to the expected operating temperature (also see chart).
Above 4° C, use SAE 30
Below 4° C and down to -12° F, use 10W-30
Below -12° C, use synthetic 5W-30

Any attempt to crank or start the engine before it has
been properly serviced with the recommended oil may
result in an engine failure.
Operation
9
TEMPERATURE IN DEGREES CELSIUS ( C)
1. Place generator on a level surface (not to exceed 15° in any
direction).
2. Clean area around oil fill and remove oil fill cap.
3. Slowly fill engine with oil through the oil fill opening until it
reaches the full mark. Stop filling occasionally to check oil
level. (Engine oil is full when level is up to the threads of the
oil fill plug, see Figure 9.)
4. Install oil fill cap and finger tighten securely.
5. Check engine oil level before starting each time thereafter.
Figure 9 – Oil Level
2.6.2 ADDING GASOLINE

NEVER fill fuel tank indoors. Avoid spilling
gasoline on hot engine. Allow engine to cool
entirely before adding fuel. NEVER fill fuel tank
when engine is running or hot. DO NOT light
a cigarette or smoke when filling the fuel tank.
Gasoline is highly flammable and its vapors are
EXPLOSIVE.

Do not overfill the fuel tank. Always leave room
for fuel expansion. If the fuel tank is overfilled,
fuel can over flow onto a hot engine and cause
fire or an explosion. Wipe up any spilled fuel
immediately.
1. Use regular UNLEADED gasoline with the generator engine. Do
not use premium gasoline. Do not mix oil with gasoline.
2. Clean area around fuel fill cap, remove cap.
3. Slowly add unleaded regular gasoline to fuel tank. Fill to
bottom of screen filter. Be careful not to overfill (Figure 10).
4. Install fuel cap and wipe up any spilled gasoline.
IMPORTANT: It is important to prevent gum deposits from forming
in fuel system parts such as the carburetor, fuel hose or tank
during storage. Alcohol-blended fuels (called gasohol, ethanol
or methanol) can attract moisture, which leads to separation and
formation of acids during storage. Acidic gas can damage the fuel
system of an engine while in storage. To avoid engine problems,
the fuel system should be emptied before storage of 30 days or
longer. See the "Storage" section. Never use engine or carburetor
cleaner products in the fuel tank as permanent damage may occur.
Figure 10 - Fuel Tank
DO NOT Fill Above Lip
Fuel
Fuel Tank
2.7 TO START THE ENGINE
Never start or stop engine with electrical devices plugged into
the receptacles AND devices turned on.
1. Unplug all electrical loads from the unit's receptacles before
starting the engine.
2. Make sure the unit is in a level position (not to exceed 15° in
any direction).
3. Open the fuel shut-off valve (Figure 11).
4. Pull engine CHOKE knob outward to “Full Choke” position
(Figure 12).
Figure 11 – Fuel Shut-off Valve
Operation
10
Figure 12 – Choke Operation
2.7.1 MANUAL (RECOIL) STARTING
1. To start the generator, put the Start/Run/Stop switch in the
RUN position.
2. Firmly grasp the recoil handle and pull slowly until increased
resistance is felt. Pull rapidly up and away to start engine.
3. When the engine starts, push choke knob to “1/2 Choke”
position until the engine runs smoothly and then fully in to the
“Run” position. If engine falters, pull choke knob back out to
“1/2 Choke” position until the engine runs smoothly and then
to “Run” position.
NOTE:
If engine fires, but does not continue to run, pull choke knob
to “Full Choke” and repeat starting instructions.
2.7.2 ELECTRIC STARTING
1. To start the engine, press and hold the Start/Run/Stop switch
in the “Start” position. The engine will crank and attempt to
start. When the engine starts, release the switch to the run
position.
2. When the engine starts, push choke knob to “1/2 Choke”
position until the engine runs smoothly and then fully in to the
“Run” position. If engine falters, pull choke knob back out to
“1/2 Choke” position until the engine runs smoothly and then
to “Run” position.
3. This generator is also equipped with a manual recoil starter
which may be used if the battery is discharged.
NOTE:
The switch must be in the RUN position.
2.8 STOPPING THE ENGINE
1. Shut off all loads, then unplug the electrical loads from
generator panel receptacles. Never start or stop the engine
with electrical devices plugged in and turned on.
2. Let engine run at no-load for several minutes to stabilize the
internal temperatures of engine and generator.
3. Move Start/Run/Stop switch to the “Stop” position.
4. Close fuel valve.
2.9 LOW OIL PRESSURE SHUTDOWN SYSTEM
The engine is equipped with a low oil pressure sensor that shuts
down the engine automatically when the oil pressure drops below
5 psi. A delay built into the low oil shutdown system allows oil
pressure to build during starting. The delay allows the engine to
run for about 10 seconds before sensing oil pressure. If the engine
shuts down by itself and the fuel tank has enough gasoline, check
engine oil level.
2.9.1 RESTARTING
If trying to restart the engine within 10 seconds after it shuts down,
the engine may NOT start. The system needs 5 to 10 seconds to
reset.
If the engine is restarted after such a shutdown and the low oil
pressure has not been corrected, the engine will run for about 10
seconds as described above and then stop.
2.10 CHARGING THE BATTERY (ELECTRIC START
UNITS ONLY)

Storage batteries give off explosive hydrogen
gas while recharging. An explosive mixture will
remain around the battery for a long time after
it has been charged. The slightest spark can
ignite the hydrogen and cause an explosion.
Such an explosion can shatter the battery and
cause blindness or other serious injury.
Do not permit smoking, open flame, sparks
or any other source of heat around a battery.
Wear protective goggles, rubber apron and
rubber gloves when working around a battery.
Battery electrolyte fluid is an extremely
corrosive sulfuric acid solution that can cause
severe burns. If spill occurs flush area with
clear water immediately.
NOTE:
The battery shipped with the generator has been fully charged.
A battery may lose some of its charge when not in use for
prolonged periods of time. If the battery is unable to crank the
engine, plug in the 12V charger included in the accessory box.
RUNNING THE GENERATOR DOES NOT CHARGE THE BATTERY.
Use battery charger plug to keep the battery charged and ready for
use. Battery charging should be done in a dry location.
1. Plug charger into “Battery Charger Input” jack, located on the
control panel. Plug wall receptacle end of the battery charger
into a 230 Volt AC wall outlet.
2. Unplug battery charger from wall outlet and control panel jack
when generator is going to be in use.
Operation
11
NOTE:
Do not use the battery charger for more than 48 hours at one
charge.
Figure 13 - Battery Charger Jack
BATTERY
CHARGER
INPUT
3.1 MAINTENANCE SCHEDULE
Follow the calendar intervals. More frequent service is required
when operating in adverse conditions noted below.
Check Oil Level At Each Use
Change Oil and Oil Filter‡ *Every Season/Every 100 Hours
Clean Spark Arrestor Screen **Every Season/Every 100 Hours
Service Air Filter **Every Season/Every 200 Hours
Replace Spark Plug Every Season
Change oil after first 30 hours of operation then every season.
* Change oil and oil filter every month when operating under heavy load or in
high temperatures.
** Clean more often under dirty or dusty operating conditions. Replace air filter
parts if very dirty.
3.2 PRODUCT SPECIFICATIONS
3.2.1 GENERATOR SPECIFICATIONS
Model
Rated Max. Power ...................................................................5.6 kW**
Surge Power ...............................................................................8400W
Rated AC Voltage .............................................................................230
Rated Max AC Load
Current @ 230V .............................................................24.3 Amps**
Rated Frequency .................................................... 50 Hz @ 3000 RPM
Phase ................................................................................ Single Phase
Rated DC Voltage ...................................................................... 12 Volts
Battery Type .................................................................... 10 AH, 12VDC
Model
Rated Max. Power ...................................................................6.4 kW**
Surge Power ...............................................................................9600W
Rated AC Voltage .............................................................................230
Rated Max AC Load
Current @ 230V .............................................................27.8 Amps**
Rated Frequency .................................................... 50 Hz @ 3000 RPM
Phase ................................................................................ Single Phase
Rated DC Voltage ...................................................................... 12 Volts
Battery Type .................................................................... 10 AH, 12VDC
** Operating temperature range: 18° C (0° F) to 40° C ( 104° F). When operating
above 25° C (77° F), there may be a decrease in engine power.
** Maximum wattage and current are subject to, and limited by, such factors
as fuel Btu content, ambient temperature, altitude, engine condition, etc..
Maximum power decreases about 3.5% for each 305 meters (1,000 feet)
above sea level.
3.2.2 ENGINE SPECIFICATIONS
Displacement ............................................................................... 407cc
Spark Plug Type ...................................Champion RC14YC or Equivalent
Spark Plug Part No. ...................................................................0E7585
Spark Plug Gap ........................................................................0.76 mm
Gasoline Capacity ............................................................... 34.07 Liters
Oil Type.................................... See Chart in "Adding Engine Oil" Section
Oil Capacity ............................................ w/ Filter Change = 1.42 Liters
w/o Filter Change = 1.136 Liters
Oil Filter Part No. . ....................................................................070185B
Run Time/Fuel Consumption-1/2 Load .....10 Hours / 3.4 Liters per hour
3.3 GENERAL RECOMMENDATIONS
The warranty of the generator does not cover items that have been
subjected to operator abuse or negligence. To receive full value
from the warranty, the operator must maintain the generator as
instructed in this manual.
Some adjustments will need to be made periodically to properly
maintain the generator.
All adjustments in the Maintenance section of this manual should
be made at least once each season. Follow the requirements in the
"Maintenance Schedule".
NOTE:
Once a year replace the spark plug and replace the air filter.
A new spark plug and clean air filter assure proper fuel-air
mixture and help the engine run better and last longer.
3.3.1 GENERATOR MAINTENANCE
Generator maintenance consists of keeping the unit clean and dry.
Operate and store the unit in a clean dry environment where it will
not be exposed to excessive dust, dirt, moisture or any corrosive
vapors. Cooling air slots in the generator must not become
clogged with snow, leaves, or any other foreign material.
Check the cleanliness of the generator frequently and clean when
dust, dirt, oil, moisture or other foreign substances are visible on
its exterior surface.

Never insert any object or tool through the air cooling
slots, even if the engine is not running.
NOTE:
DO NOT use a garden hose to clean generator. Water can
enter the engine fuel system and cause problems. In addition,
if water enters the generator through cooling air slots, some
water will be retained in voids and crevices of the rotor
and stator winding insulation. Water and dirt buildup on the
generator internal windings will eventually decrease the
insulation resistance of these windings.
Maintenance
12
3.3.2 TO CLEAN THE GENERATOR
Use a damp cloth to wipe exterior surfaces clean.
A soft, bristle brush may be used to loosen caked on dirt, oil, etc.
A vacuum cleaner may be used to pick up loose dirt and debris.
• Low pressure air (not to exceed 25 psi) may be used to
blow away dirt. Inspect cooling air slots and openings on the
generator. These openings must be kept clean and unobstructed.
3.3.3 ENGINE MAINTENANCE

When working on the generator, always disconnect
negative cable from battery. Also disconnect spark plug
wire from spark plug and keep wire away from spark
plug.
3.3.4 CHECKING OIL LEVEL
See the “BEFORE STARTING THE GENERATOR” section for
information on checking the oil level. The oil level should be
checked before each use, or at least every eight hours of operation.
Keep the oil level maintained.
3.3.5 CHANGING THE OIL AND OIL FILTER
Change the oil and filter after the first 30 hours of operation.
Change the oil every 100 hours or every season thereafter. If
running this unit under dirty or dusty conditions, or in extremely
hot weather, change the oil more often.

Hot oil may cause burns. Allow engine to cool before
draining oil. Avoid prolonged or repeated skin exposure
with used oil. Thoroughly wash exposed areas with soap.
Use the following instructions to change the oil:
1. Clean area around oil drain cap.
2. Remove oil drain cap from the drain hose and oil fill plug to
drain oil completely into a suitable container.
3. When oil has completely drained, install oil drain cap and
tighten securely.
4. Place a suitable container beneath the oil filter and turn filter
counterclockwise to remove. Discard according to local
regulations.
5. Coat gasket of new filter with clean engine oil. Turn filter
clockwise until gasket contacts lightly with filter adapter. Then
tighten an additional 3/4 turn.
6. Fill oil sump with recommended oil and replace the oil fill plug.
(See “Before Starting the Generator” for oil recommendations).
7. Wipe up any spilled oil.
8. Dispose of used oil at a proper collection center.
3.3.6 REPLACING THE SPARK PLUG
Use Champion RC14YC spark plug or equivalent. Replace the
plug once each year. This will help the engine start easier and
run better.
1. Stop the engine and pull the spark plug wire off of the spark
plug.
2. To gain access, remove the four (4) socket head screws and
take off the side panel.
3. Clean the area around the spark plug and remove it from the
cylinder head.
4. Set the spark plug's gap to .76 mm. Install the correctly
gapped spark plug into the cylinder head (Figure 14).
5. Push the boot firmly on the spark plug and install side panel.
Figure 14 – Spark Plug Gap
3.4 SERVICE AIR FILTER
The engine will not run properly and may be damaged if using a
dirty air filter. Clean or replace the air filter paper filter every 200
hours or once a year (Figure 15). Clean or replace more often if
operating under dusty conditions. To clean or replace paper air
filter:
1. Remove air filter cover and remove paper filter (Figure 15).
2. Clean paper filter by tapping it gently on a solid surface. If the
filter is too dirty, replace it with a new one. Dispose of the old
filter properly.
3. Clean air filter cover. Next insert new paper filter into the base
of the air filter. Re-install air filter cover.
NOTE:
To order a new air filter, please contact the nearest authorized
service center at www.generac.com/Dealer Locator. The air
filter part number is 073111.
Figure 15 – Air Filter
AIR FILTER
COVER
Maintenance
13
3.5 CLEAN SPARK ARRESTOR SCREEN
The engine exhaust muffler has a spark arrestor screen. Inspect
and clean the screen at least once each year (Figure 16). If unit is
used regularly, inspect and clean more often.
If using the generator on any forest-covered,
brush-covered or grass-covered unimproved
land, it must equipped with a spark arrestor.
The spark arrestor must be maintained in good
condition by the owner/operator.
Clean and inspect the spark arrestor when the engine is at ambient
temperature as follows:
1. Loosen the clamp and remove the spark arrestor screen from
the muffler.
2. Inspect screen and replace if torn, perforated or otherwise
damaged. DO NOT USE a defective screen. If screen is not
damaged, clean it with commercial solvent.
3. Replace the spark arrestor and secure with the clamp.
Figure 16 – Spark Arrestor Screen
ARRESTOR
SCREEN
CLAMP
SPARK
ARRESTOR
SCREEN
3.6 GENERAL
The generator should be started at least once every 30 days and
be allowed to run at least 30 minutes. If this cannot be done and
the unit must be stored for more than 30 days, use the following
information as a guide to prepare it for storage.
NEVER store engine with fuel in tank indoors
or in enclosed, poorly ventilated areas where
fumes may reach an open flame, spark or pilot
light as on a furnace, water heater, clothes dryer
or other gas appliance.

Allow unit to cool entirely before storage.
3.7 LONG TERM STORAGE
It is important to prevent gum deposits from forming in essential
fuel system parts such as the carburetor, fuel hose or tank during
storage. Also, experience indicates that alcohol-blended fuels
(called gasohol, ethanol or methanol) can attract moisture, which
leads to separation and formation of acids during storage. Acidic
gas can damage the fuel system of an engine while in storage.
To avoid engine problems, the fuel system should be emptied
before storage of 30 days or longer, as follows:
1. Add a quality gasoline stabilizer to the fuel per the manufacturers
specifications, and run the unit for 10-15 minutes.
2. After engine cools down, remove all gasoline from the fuel
tank. Use a commercially available, non-conductive vacuum
siphon.
Drain fuel into approved container outdoors,
away from open flame. Be sure engine is cool.
Do not smoke.
3. Start and run engine until engine stops from lack of fuel.
4. After engine cools down, drain oil from engine. Refill with
recommended grade.
5. Remove spark plug and pour about 1/2 ounce (15 ml) of
engine oil into the cylinder. Cover spark plug hole with rag. Pull
the recoil starter a couple times to lubricate the piston rings
and cylinder bore. A fogging agent can also be used in the
place of oil.

Avoid spray from spark plug hole when
cranking engine.
6. Install and tighten spark plug. Do not connect spark plug wire.
7. Clean the generator outer surfaces. Check that cooling air
slots and openings on generator are open and unobstructed.
8. Store the unit in a clean, dry place.
3.8 OTHER STORAGE TIPS
Do not store gasoline from one season to another.
Replace any gasoline can that starts to rust. Rust and/or dirt in
the gasoline will cause problems with the carburetor and fuel
system.
• If possible, store the unit indoors and cover it to give protection
from dust and dirt. Cover the unit with a suitable protective
cover that does not retain moisture.
BE SURE TO EMPTY THE FUEL TANK. If it is not practical
to empty the fuel tank and the unit is to be stored for some
time, use a commercially available fuel stabilizer added to the
gasoline to increase the life of the gasoline.

NEVER cover the generator while engine and
exhaust area are warm.
Maintenance
14
4.1 BATTERY REPLACEMENT
NOTE:
The battery shipped with the generator has been fully charged.
A battery may lose some of its charge when not in use for
prolonged periods of time. If the battery is unable to crank
the engine, plug in the 12V charger included in the accessory
box (see the Charging a Battery section). RUNNING THE
GENERATOR DOES NOT CHARGE THE BATTERY.
The battery shipped with the generator has been provided fully
charged. To replace the battery (See Figure 17):
1. Remove the side panel as shown. Remove the four bolts
securing the fuel tank.
2. Turn the fuel valve on the control panel to the "OFF" position.
Pull the fuel tank back slightly and remove the fuel hose that
runs from the engine to the fuel valve.

Drain fuel into approved container outdoors, away from
open flame. Be sure engine is cool. Do not smoke in the
vicinity or light a cigarette.
3. Push the fuel valve from the control panel and remove the fuel
tank.
4. Remove the battery wire connections (black wire first) and the
battery hold-down bracket.
5. Replace the battery, connecting the RED wire to the POSITIVE
(+) terminal and the BLACK wire to the NEGATIVE (-) terminal
NOTE:
Start all four screws on the side panel before tightening or it
may not be possible to get all the screws in place.
Figure 17 – Battery Removal
Battery Service
15
5.1 TROUBLESHOOTING GUIDE
PROBLEM CAUSE CORRECTION
Engine is running, but no AC output
is available.
1. Circuit breaker is open.
2. Poor connection or defective cord set.
3. Connected device is bad.
4. Fault in generator.
1. Reset circuit breaker.
2. Check and repair.
3. Connect another device that is in good condition.
4. Contact Authorized Service Facility.
Engine runs good but bogs down
when loads are connected.
1. Short circuit in a connected load.
2. Generator is overloaded.
3. Engine speed is too slow.
4. Shorted generator circuit.
1. Disconnect shorted electrical load.
2. See “Don’t Overload the Generator” .
3. Contact Authorized Service Facility.
4. Contact Authorized Service Facility.
Engine will not crank. 1. Battery weak or dead. 1. Recharge or replace battery (see "No Battery
Charger DC output" at bottom of guide).
2. Start engine manually using recoil starter.
Engine will not start; or starts and
runs rough.
1. Fuel shut-off is OFF.
2. Dirty air filter.
3. Out of gasoline.
4. Stale gasoline.
5. Spark plug wire not connected to spark plug.
6. Bad spark plug.
7. Water in gasoline.
8. Over-choking.
9. Low oil level.
10. Excessive rich fuel mixture.
11. Intake valve stuck open or closed.
12. Engine has lost compression.
1. Turn Fuel shut-off ON.
2. Clean or replace air filter.
3. Fill fuel tank.
4. Drain fuel tank and fill with fresh fuel.
5. Connect wire to spark plug.
6. Replace spark plug.
7. Drain fuel tank; fill with fresh fuel.
8. Put choke knob to No Choke position.
9. Fill crankcase to proper level.
10. Contact Authorized Service Facility.
11. Contact Authorized Service Facility.
12. Contact Authorized Service Facility.
Engine shuts down during
operation.
1. Out of gasoline.
2. Low oil level.
3. Fault in engine.
1. Fill fuel tank.
2. Fill crankcase to proper level.
3. Contact Authorized Service Facility.
Engine lacks power. 1. Load is too high.
2. Dirty air filter.
3. Engine needs to be serviced.
1. See “Don’t Overload the Generator”.
2. Replace air filter.
3. Contact Authorized Service Facility.
Engine “hunts” or falters. 1. Choke is opened too soon.
2. Carburetor is running too rich or too lean.
1. Move choke to halfway position until engine runs
smoothly.
2. Contact Authorized Service Facility.
No Battery Charger DC output. 1. Battery posts are corroded.
2. Battery cable is bad.
3. Battery is defective.
4. Receptacle is bad.
5. Battery Charger in-line fuse (1.5A) melted open.
1. Clean battery posts.
2. Replace cable.
3. Check battery condition; replace if defective.
4. Contact Authorized Service Facility.
5. Replace fuse with identical 1.5A replacement fuse
only (located inside control panel).
Troubleshooting
Manual Part No. 0J9224 Revision B (11/12/15) Printed in U.S.A.
www.generac.com
Manual del propietario
Generador portátil Serie XG 5600-6400 W, 50 Hz
GARANTÍA
LIMITADA
AÑOS
¡PELIGRO!
¡EMANACIONES DE ESCAPE MORTALES! ¡Use ÚNICAMENTE
en EXTERIORES, lejos de ventanas, puertas y ventilaciones!
O ESTÁN DESTINADOS AL USO EN APLICACIONES CRÍTICAS
DE SOPORTE A LA VIDA HUMANA.
GUARDE este manual. Proporcione este manual a todos los
operadores del generador.
Introducción ............................................................ 1
Lea este manual minuciosamente .......................... 1
Reglas de seguridad ............................................... 1
Registro .................................................................. 3
Información general................................................ 4
1.1 Desembalaje ..................................................................4
1.1.1 Caja de accesorios ............................................4
1.2 Armado .........................................................................4
1.2.1 Montaje del kit de rueda y el pie del bastidor ...... 4
Operación ............................................................... 5
2.1 Conozca el generador .....................................................5
2.1.1 Conexión de la batería ........................................6
2.2 Horómetro ......................................................................6
2.3 Juegos de cordones y enchufes de conexión .................6
2.3.1 Tomacorriente de 230 VCA, 16 A,
CEE 7/4, Tipo F .................................................6
2.3.2 Tomacorriente de 230 VCA, 30 A ....................... 7
2.3.3 Cable adaptador, 50 Hz (solo XG5600/XG6400) ....7
2.4 Cómo usar el generador .................................................7
2.4.1 Conexión a tierra del sistema .............................8
2.4.2 Conexión al sistema eléctrico de un edificio .......8
2.4.3 Conexión de cargas eléctricas ............................8
2.5 No sobrecargue el generador..........................................8
2.6 Antes de poner en marcha el generador .........................8
2.6.1 Cómo añadir aceite de motor .............................8
2.6.2 Cómo añadir gasolina ........................................9
2.7 Para poner en marcha ....................................................9
2.7.1 Arranque manual (con tirador y cuerda) ........... 10
2.7.2 Arranque eléctrico ............................................10
2.8 Parada del motor .......................................................... 10
2.9 Sistema de parada por baja presión de aceite ............... 10
2.9.1 Volver a poner en marcha ................................10
2.10 Carga de la batería (solo unidades con
arranque eléctrico) .......................................................10
Mantenimiento ...................................................... 11
3.1 Programa de mantenimiento ......................................... 11
3.2 Especificaciones del producto ......................................11
3.2.1 Especificaciones del generador ........................11
3.2.2 Especificaciones del motor ..............................11
3.3 Recomendaciones generales ........................................11
3.3.1 Mantenimiento del generador ...........................11
3.3.2 Limpieza del generador ....................................12
3.3.3 Mantenimiento del motor .................................12
3.3.4 Comprobación del nivel de aceite ..................... 12
3.3.5 Cambio de aceite y sustitución del
filtro de aceite ..................................................12
3.3.6 Sustitución de la bujía ...................................... 12
3.4 Servicio del filtro de aire ............................................... 12
3.5 Limpieza del tamiz del supresor de chispas ..................13
3.6 Normas generales ........................................................13
3.7 Almacenamiento de largo plazo ....................................13
3.8 Otros consejos sobre almacenamiento .........................13
Servicio de la batería ........................................... 14
4.1 Sustitución de la batería ...............................................14
Resolución de problemas ..................................... 15
5.1 Guía de resolución de problemas .................................15
Garantía ...................................................Contratapa
Índice
/