Huawei P Smart Z Инструкция по началу работы

Quick Start Guide

Краткое руководство пользователя

Жылдам бастау нұсқаулығы

STK-LX1

Contents

English............................................................................ 1

Русский ........................................................................12

Қазақ тілі.......................................................................43

i

Know Your Device

Before using the device, familiarize yourself with its basic

operations.

l To power on your device, press and hold the power button

until the screen turns on.

l To power off your device, press and hold the power button,

and then touch .

l To restart your device, press and hold the power button,

and then touch .

l Press and hold the power button for 10 or more seconds to

forcibly restart your device.

NFC

3

6

5

2

1

4

7

Card slot Fingerprint scanner

Type-C port Headset jack

Power button Volume button

Pop-up front camera

l Please keep the NFC area close to other devices or

objects while using the NFC function.

l Check out the pre-installed Tips app and master all the

great features on your device.

English

1

Getting Started

l Do not insert or remove the SIM card when your device

is powered on.

l Ensure that the card is correctly aligned and that the

card tray is level when you insert it into your device.

l Be careful not to scratch your device or hurt yourself

when using the eject pin.

l Store the eject pin out of the reach of children to

prevent accidental swallowing or injury.

l Do not use cut or modied SIM or microSD cards with

your device as these may not be recognized and could

damage the card tray (slot).

l If your SIM card does not match your device, please

contact your carrier.

Follow the instructions in the following gures to set up your

device. Please use the eject pin included.

3

2

1

microSD

nano-SIM 1

nano-SIM 2

2

Dual Card Dual Standby Single

Pass

Your device supports only dual card dual standby single pass,

which means you cannot use both SIM cards for calls or data

services simultaneously.

l When you are on a call using SIM card 1, SIM card 2 cannot

be used to make or answer calls. If someone calls SIM card

2, the caller will hear a voice message similar to "The

subscriber you dialed is out of the service area" or "The

subscriber you dialed cannot be connected for the moment,

please try again later." The actual message will vary by

service provider.

l When you are using SIM card 1's data service, SIM card 2's

data service will be disabled.

Your device's single pass feature helps reduce power

consumption and increase your device's standby time. It is not

related to your service provider's network conditions.

l You can enable call forwarding between SIMs on the

device to avoid missed calls.

3

For More Information

If you encounter any problems while using your device, you

can obtain help from the following resources:

l Visit http://consumer.huawei.com/en to view device

information, frequently asked questions and other

information.

l Visit http://consumer.huawei.com/en/support for the most

up-to-date contact information for your country or region.

l You can nd service hotlines, retailer addresses, service

policies and more information for your local region in

HiCare.

Go to Settings and touch System > About phone > Legal to

view legal information for your product.

Go to Settings and touch System > About phone > Legal >

Safety information to view safety information for your

product.

Go to Settings and touch System > About phone >

Authentication info to view regulatory information for your

product.

Go to Settings and touch System > Certication logos to

view more information on certication logos for your product.

All pictures and illustrations in this guide, including but

not limited to the device color, size, and display content,

are for your reference only. The actual device may vary.

Nothing in this guide constitutes a warranty of any kind,

express or implied.

4

Safety Information

Please read all of the safety information carefully before using

your device to ensure its safe and proper operation and to

learn how to dispose of your device properly.

Operation and safety

l To prevent possible hearing damage, do not

listen at high volume levels for long periods.

l Using an unapproved or incompatible power adapter,

charger, or battery may damage your device, shorten its

lifespan, or cause a re, explosion, or other hazards.

l Ideal operating temperatures are 0 °C to 35 °C. Ideal

storage temperatures are -20 °C to +45 °C.

l Pacemaker manufacturers recommend that a minimum

distance of 15 cm be maintained between a device and a

pacemaker to prevent potential interference with the

pacemaker. If using a pacemaker, hold the device on the

side opposite the pacemaker and do not carry the device in

your front pocket.

l Keep the device and the battery away from excessive heat

and direct sunlight. Do not place them on or in heating

devices, such as microwave ovens, stoves, or radiators.

l Observe local laws and regulations while using the device.

To reduce the risk of accidents, do not use your wireless

device while driving.

l While ying in an aircraft or immediately before boarding,

only use your device according to instructions provided. Use

of a wireless device in an aircraft may disrupt wireless

networks, present a hazard to aircraft operation, or be

illegal.

l To prevent damage to your device's parts or internal

circuits, do not use it in dusty, smoky, damp, or dirty

environments or near magnetic elds.

l When charging the device, make sure the power adapter is

plugged into a socket near the devices and is easily

accessible.

l Unplug the charger from electrical outlets and the device

when not in use.

l Do not use, store or transport the device where ammables

or explosives are stored (in a gas station, oil depot, or

5

chemical plant, for example). Using your device in these

environments increases the risk of explosion or re.

l Dispose of this device, the battery, and accessories

according to local regulations. They should not be disposed

of in normal household waste. Improper battery use may

lead to re, explosion, or other hazards.

l This device contains a built-in battery. Do not attempt to

replace the battery by yourself. Otherwise, the device may

not run properly or it may damage the battery. For your

personal safety and to ensure that your device runs

properly, you are strongly advised to contact a Huawei

authorized service center for a replacement.

Disposal and recycling information

The crossed-out wheeled-bin symbol on your product, battery,

literature or packaging reminds you that all electronic products

and batteries must be taken to separate waste collection

points at the end of their working lives; they must not be

disposed of in the normal waste stream with household

garbage. It is the responsibility of the user to dispose of the

equipment using a designated collection point or service for

separate recycling of waste electrical and electronic equipment

(WEEE) and batteries according to local laws.

Proper collection and recycling of your equipment helps ensure

electrical and electronic equipment (EEE) waste is recycled in a

manner that conserves valuable materials and protects human

health and the environment, improper handling, accidental

breakage, damage, and/or improper recycling at the end of its

life may be harmful for health and environment. For more

information about where and how to drop off your EEE waste,

please contact your local authorities, retailer or household

waste disposal service or visit the website http://

consumer.huawei.com/en/.

Reduction of hazardous substances

This device and its electrical accessories are compliant with

local applicable rules on the restriction of the use of certain

hazardous substances in electrical and electronic equipment,

such as EU REACH, RoHS and Batteries (where included)

regulations. For declarations of conformity about REACH and

6

RoHS, please visit our web site http://consumer.huawei.com/

certication.

EU regulatory conformance

Body worn operation

The device complies with RF specications when used near

your ear or at a distance of 0.50 cm from your body. Ensure

that the device accessories, such as a device case and device

holster, are not composed of metal components. Keep the

device away from your body to meet the distance requirement.

The highest SAR value reported for this device type when

tested at the ear is

STK-LX1 0.84 W/kg

And when properly worn on the body is

STK-LX1 1.08 W/kg

Statement

Hereby, Huawei Technologies Co., Ltd. declares that this device

STK-LX1 is in compliance with the essential requirements and

other relevant provisions of Directive 2014/53/EU.

The most recent and valid version of the DoC (Declaration of

Conformity) can be viewed at http://consumer.huawei.com/

certication.

This device may be operated in all member states of the EU.

Observe national and local regulations where the device is

used.

This device may be restricted for use, depending on the local

network.

Restrictions in the 2.4 GHz band:

Norway: This subsection does not apply for the geographical

area within a radius of 20 km from the centre of Ny-Ålesund.

Restrictions in the 5 GHz band:

According to Article 10 (10) of Directive 2014/53/EU, the

packaging shows that this radio equipment will be subject to

some restrictions when placed on the market in Belgium (BE),

Bulgaria (BG), the Czech Republic (CZ), Denmark (DK),

Germany (DE), Estonia (EE), Ireland (IE), Greece (EL), Spain (ES),

France (FR), Croatia (HR), Italy (IT), Cyprus (CY), Latvia (LV),

Lithuania (LT), Luxembourg (LU), Hungary (HU), Malta (MT),

Netherlands (NL), Austria (AT), Poland (PL), Portugal (PT),

Romania (RO), Slovenia (SI), Slovakia (SK), Finland (FI), Sweden

(SE), the United Kingdom (UK), Turkey (TR), Norway (NO),

Switzerland (CH), Iceland (IS), and Liechtenstein (LI).

7

The WLAN function for this device is restricted to indoor use

only when operating in the 5150 to 5350 MHz frequency

range.

Frequency Bands and Power

(a) Frequency bands in which the radio equipment operates:

Some bands may not be available in all countries or all areas.

Please contact the local carrier for more details.

(b) Maximum radio-frequency power transmitted in the

frequency bands in which the radio equipment operates: The

maximum power for all bands is less than the highest limit

value specied in the related Harmonized Standard.

The frequency bands and transmitting power (radiated and/or

conducted) nominal limits applicable to this radio equipment

are as follows:

STK-LX1 GSM900: 35dBm, GSM1800: 32dBm,

WCDMA900/2100: 25.7dBm, LTE Band

1/3/7/8/20: 25.7dBm, Wi-Fi 2.4G: 20dBm,

Bluetooth: 20dBm, Wi-Fi 5G: 5150-5250MHz:

23dBm, 5250-5350MHz: 20dBm,

5470-5725MHz: 20dBm, 5725-5850MHz:

25mW, NFC: 42 dBuA/m at 10 m

Accessories and Software Information

Some accessories are optional in certain countries or regions.

Optional accessories can be purchased from a licensed vendor

as required. The following accessories are recommended:

Adapters: HW-050200X01, HW-050200X02 (X represents the

different plug types used, which can be either C, U, J, E, B, A, I,

R, Z or K, depending on your region)

Batteries: HB446486ECW

Earphones: 1293-3283-3.5mm-322, MEND1532B528A02

The product software version is STK-LX1: STK-LX1 9.0.1.15.

Software updates will be released by the manufacturer to x

bugs or enhance functions after the product has been

released. All software versions released by the manufacturer

have been veried and are still compliant with the related

rules.

All RF parameters (for example, frequency range and output

power) are not accessible to the user, and cannot be changed

by the user.

For the most recent information about accessories and

software, please see the DoC (Declaration of Conformity) at

http://consumer.huawei.com/certication.

8

FCC Regulatory Compliance

Body worn operation

The device complies with RF specications when used near

your ear or at a distance of 1.50 cm from your body. Ensure

that the device accessories, such as a device case and device

holster, are not composed of metal components. Keep the

device away from your body to meet the distance requirement.

Certication information (SAR)

This device is also designed to meet the requirements for

exposure to radio waves established by the Federal

Communications Commission (USA).

The SAR limit adopted by the USA is 1.6 W/kg averaged over

one gram of tissue. The highest SAR value reported to the FCC

for this device type complies with this limit.

The highest SAR value reported to the FCC for this device type

when using it at the ear is

STK-LX1 1.07 W/kg

And when properly worn on the body is

STK-LX1 0.42 W/kg

And when using the Wi-Fi hotspot function is

STK-LX1 0.88 W/kg

FCC statement

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following

measures:

--Reorient or relocate the receiving antenna.

--Increase the separation between the equipment and receiver.

--Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

--Consult the dealer or an experienced radio/TV technician for

help.

9

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may

cause undesired operation.

Caution: Any changes or modications to this device not

expressly approved by Huawei Technologies Co., Ltd. for

compliance could void the user's authority to operate the

equipment.

10

Legal Notice

Trademarks and Permissions

, , and are trademarks or

registered trademarks of Huawei Technologies Co., Ltd.

Android™ is a trademark of Google Inc.

LTE is a trademark of ETSI.

The Bluetooth

®

word mark and logos are registered

trademarks owned by Bluetooth SIG, Inc. and any use of such

marks by Huawei Technologies Co., Ltd. is under license.

Wi-Fi

®

, the Wi-Fi CERTIFIED logo, and the Wi-Fi logo are

trademarks of Wi-Fi Alliance.

The N-Mark is a trademark or registered trademark

of NFC Forum, Inc. in the United States and in other countries.

Privacy Policy

To better understand how we protect your personal

information, please see the privacy policy at http://

consumer.huawei.com/privacy-policy.

THIS DOCUMENT IS FOR INFORMATION PURPOSE ONLY, AND

DOES NOT CONSTITUTE ANY KIND OF WARRANTIES.

11

Знакомство с устройством

Перед использованием устройства познакомьтесь с

основными операциями.

l Чтобы включить устройство, нажмите и удерживайте

кнопку питания, пока не включится экран устройства.

l Чтобы выключить устройство, нажмите и

удерживайте кнопку питания, затем нажмите .

l Чтобы перезагрузить устройство, нажмите и

удерживайте кнопку питания, затем нажмите .

l Нажмите и удерживайте кнопку питания 10 секунд

или дольше, чтобы принудительно перезагрузить

устройство.

NFC

3

6

5

2

1

4

7

Слот для установки

карты

Датчик отпечатка

пальца

Порт Type-C

Разъем для

наушников

Кнопка питания

Кнопка регулировки

громкости

Фронтальная

выдвижная камера

Русский

12

l При использовании функции NFC размещайте

область NFC-датчика устройства рядом с

другими устройствами или объектами.

l Посмотрите предустановленное приложение

Советы и узнайте, как пользоваться всеми

функциями на Вашем устройстве.

13

Начало работы

l Не вставляйте и не извлекайте SIM-карту, когда

устройство включено.

l Убедитесь, что карта корректно размещена в

слоте при установке слота в устройство.

l Не поцарапайте себя или устройство, используя

инструмент для извлечения карт.

l Храните инструмент для извлечения карт в

недоступном для детей месте.

l Не устанавливайте обрезанные или измененные

вручную SIM-карты или карты microSD на Вашем

устройстве. Они не будут определены, могут

повредить слот для установки карт.

l Если Ваша SIM-карта не подходит к Вашему

устройству, обратитесь к оператору для ее

замены.

Подготовьте устройство к работе, следуя инструкциям

на нижеприведенных рисунках. Используйте

инструмент для извлечения карт, входящий в комплект

поставки.

3

2

1

microSD

nano-SIM 1

nano-SIM 2

14

Поддержка двух SIM-карт в

режиме ожидания

Ваше устройство поддерживает работу двух SIM-карт в

режиме ожидания. Это значит, что Вы не сможете

одновременно использовать две SIM-карты для

вызовов или передачи данных.

l Совершая вызов с помощью SIM-карты 1, Вы не

сможете использовать SIM-карту 2 для выполнения

вызова или ответа на вызов. Если во время

разговора по SIM-карте 1 на SIM-карту 2 поступает

вызов, вызывающий абонент слышит голосовое

сообщение "Вызываемый абонент находится вне

зоны действия сети" или "Вызываемый абонент в

данный момент недоступен, позвоните позже." Текст

сообщения зависит от настроек оператора.

l Во время использования службы передачи данных

SIM-карты 1 служба передачи данных SIM-карты 2

выключена.

Функция поддержки двух SIM-карт в режиме ожидания

позволяет снизить энергопотребление устройства и

увеличить время его работы в режиме ожидания.

Работа этой функции не зависит от настроек сети

оператора.

l Вы можете включить переадресацию вызовов

между SIM-картами, установленными в

устройстве, чтобы не пропустить ни одного

звонка.

15

Дополнительная информация

Справочную информацию о работе устройства можно

найти в следующих источниках:

l Откройте http://consumer.huawei.com/en, чтобы

посмотреть данные устройства, вопросы и ответы и

другую полезную информацию.

l На веб-странице http://consumer.huawei.com/en/

support можно найти актуальную контактную

информацию в Вашей стране или регионе.

l В приложении HiCare можно найти телефон горячей

линии службы поддержки клиентов, адреса

магазинов, сервисные политики и другую полезную

информацию для Вашего региона.

Откройте Настройки, нажмите Система > О телефоне

> Правовая информация, чтобы посмотреть правовую

информацию о Вашем устройстве.

Откройте Настройки, нажмите Система > О телефоне

> Правовая информация > Сведения о

безопасности, чтобы посмотреть меры

предосторожности, которые следует соблюдать при

работе с устройством.

Откройте Настройки, нажмите Система > О телефоне

> Аутентификационные данные, чтобы посмотреть

нормативную информацию о Вашем устройстве.

Откройте Настройки, нажмите Система > Логотипы

сертификатов, чтобы посмотреть дополнительную

информацию о логотипах сертификатов Вашего

устройства.

Все изображения в данном руководстве, включая

цвет и размер устройства, а также изображения на

экране, приведены для справки. Приобретенное

устройство может отличаться от изображенного в

данном руководстве. Положения настоящего

руководства не подразумевают никаких гарантий,

явных или неявных.

16

Страница загружается...

Huawei P Smart Z Инструкция по началу работы

Похожие модели бренда

Модели других брендов