HOTPOINT/ARISTON BWMD 742 (EU) Руководство пользователя

GB

1

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Instructions for the fitter

Description of the washing machine, 6-7

Control panel

Display

Running a wash cycle, 8

Wash cycles and functions, 9

Table of wash cycles

Wash functions

Detergents and laundry, 10

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Load balancing system

Precautions and tips, 11

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 12

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 13

Service, 14

BWMD 742

Instructions for use

WASHING MACHINE

English,1

GB

ES

Español,29Italiano,15

I

Русский,43

CIS

DE

Deutsch,57

2

GB

! This instruction manual should be kept in a safe place for

future reference. If the washing machine is sold, transferred

or moved, make sure that the instruction manual remains

with the machine so that the new owner is able to familiari-

se himself/herself with its operation and features.

! Read these instructions carefully: they contain vital infor-

mation relating to the safe installation and operation of the

appliance.

Unpacking and levelling

Unpacking

1. Remove the washing machine from its packaging.

2. Make sure that the washing machine has not been

damaged during the transportation process. If it has been

damaged, contact the retailer and do not proceed any

further with the installation process.

3. Remove the 4 protective

screws (used during tran-

sportation) and the rubber

washer with the correspon-

ding spacer, located on the

rear part of the appliance

(see figure).

4. Close off the holes using the plastic plugs provided.

5. Keep all the parts in a safe place: you will need them

again if the washing machine needs to be moved to ano-

ther location.

! Packaging materials should not be used as toys for

children.

Levelling

1. Install the washing machine on a flat sturdy floor, without

resting it up against walls, furniture cabinets or anything

else.

2. If the floor is not perfectly

level, compensate for any

unevenness by tightening

or loosening the adjusta-

ble front feet (see figure);

the angle of inclination,

measured in relation to the

worktop, must not exceed

2°.

Levelling the machine correctly will provide it with stability,

help to avoid vibrations and excessive noise and prevent it

from shifting while it is operating. If it is placed on carpet or

a rug, adjust the feet in such a way as to allow a sufficient

ventilation space underneath the washing machine.

Connecting the electricity and water

supplies

Connecting the water inlet hose

1. Connect the supply pipe

by screwing it to a cold

water tap using a ¾ gas

threaded connection (see

figure).

Before performing the con-

nection, allow the water to

run freely until it is perfectly

clear.

2. Connect the inlet hose

to the washing machine by

screwing it onto the corre-

sponding water inlet of the

appliance, which is situa-

ted on the top right-hand

side of the rear part of the

appliance (see figure).

3. Make sure that the hose is not folded over or bent.

! The water pressure at the tap must fall within the values

indicated in the Technical details table (see next page).

! If the inlet hose is not long enough, contact a specialised

shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

Installation

GB

3

Connecting the drain hose

Connect the drain hose,

without bending it, to a drai-

nage duct or a wall drain

located at a height between

65 and 100 cm from the

floor;

alternatively, rest it on

the side of a washbasin

or bathtub, fastening the

duct supplied to the tap

(see figure). The free end

of the hose should not be

underwater.

! We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the same

diameter as the original hose and must not exceed 150 cm

in length.

Electrical connections

Before plugging the appliance into the electricity socket,

make sure that:

• the socket is earthed and complies with all applicable

laws;

• the socket is able to withstand the maximum power load

of the appliance as indicated in the Technical data table

(see opposite);

• the power supply voltage falls within the values indicated

in the Technical data table (see opposite);

• the socket is compatible with the plug of the washing

machine. If this is not the case, replace the socket or the

plug.

! The washing machine must not be installed outdoors,

even in covered areas. It is extremely dangerous to leave

the appliance exposed to rain, storms and other weather

conditions.

! When the washing machine has been installed, the elec-

tricity socket must be within easy reach.

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable must only be replaced by autho-

rised technicians.

Warning! The company shall not be held responsible in the

event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before you use

it for the first time, run a wash cycle with detergent and no

laundry, using the wash cycle (60°C).

65 - 100 cm

Technical data

Model

BWMD 742

Dimensions

width 59.5 cm

height 81.5 cm

depth 54.5 cm

Capacity

from 1 to 7 kg

Electrical

connections

please refer to the technical data plate

fixed to the machine

Water connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1400 rotations per minute

Test wash cycles

in accordance

with directives

1061/2010 and

1015/2010

programme

(60°) (1st press of the button);

Standard Cotton 60°C.

programme (40°) (2nd press of the button);

Standard Cotton 40°C.

This appliance conforms to the following

EC Directives:

- 2004/108/EC (Electromagnetic Compatibility)

- 2006/95/EC (Low Voltage)

- 2012/19/EU

4

GB

Instructions for the fitter

Mounting the wooden panel onto the door and inser-

ting the machine into cabinets:

In the case where the machine must be shipped for final

installation after the wooden panel has been mounted, we

suggest leaving it in its original packaging. The packaging was

designed to make it possible to mount the wooden panel

onto the machine without removing it completely (see figures

below).

The wooden panel that covers the face of the machine must

not be less than 18 mm in thickness and can be hinged on

either the right or left. For the sake of practicality when using

the machine, we recommend that the panel be hinged on the

same side as the door for the machine itself - the left.

A

B

C

D

E

Tur seite

Door Mounting Accessories (Fig. 1-2-3-4-5).

Fig. 1

N° 2 Hinges

N° 1 Magnet N° 1 Magnet plate

N° 1 Rubber plug

N° 2 Hinge Supports

N° 4 Spacers

Fig. 2

Fig. 3 Fig. 4

Fig. 5

Fig. 4/B

- No. 6 type A self-threading screws, l =13 mm.

- No. 2 type B metric, countersunk screws, l =25; for faste-

ning the magnet plate to the cabinet.

- No. 4 type C metric screws, l =15 mm; for mounting the

hinge supports to the cabinet.

- No. 4 type D metric screws, l =7 mm; for mounting the

hinges on the supports.

Mounting the Parts onto the Face of the Machine.

- Fit the hinge supports to the appliance front panel, positioning

the hole marked with an arrow in fig. 1 so that it is on the inner

side of the front panel. Fit a spacer (fig. 4/B) between the

surfaces using type C screws.

- Fit the magnet plate at the top of the opposite side, using

type B screws to fix two spacers (fig. 4/B) between the plate

and the surface.

GB

5

Using the Drilling Template.

- To trace the positions of the holes on the left-hand side of

the panel, align the drilling template to the top left side of the

panel using the lines traced on the extremities as a reference.

- To trace the positions of the holes on the right-hand side of

the panel, align the drilling template to the top right side of the

panel.

- Use an appropriately sized router to mill the holes for the two

hinges, the rubber plug and the magnet.

Mounding the Parts onto the Wooden Panel (Door).

- Insert the hinges into the holes (the movable part of the hin-

ge must be positioned facing away from the panel) and fasten

them with the 4 type A screws.

- Insert the magnet into the top hole on the opposite side of

the hinges and fasten it with the two type B screws.

- Insert the rubber plug into the bottom hole.

The panel is now ready to be mounted onto the machine.

Mounting the Panel into the machine.

Insert the nib of the hinge (indicated by the arrow in fig. 2) into

the hole for the hinge and push the panel towards the front of

the machine. Fasten the two hinges with the type D screws.

Fastening the plinth guide.

If the machine is installed at the end of a set of modular

cabinets, mount either one or both of the guides for the base

molding (as shown in fig. 8). Adjust them for depth based on

the position of the base molding, and, if necessary, fasten the

base to the guides (fig. 9).

This is how to assemble the plinth guide (fig. 8):

Fasten angle P using screw R, insert plinth guide Q into the

special slot and once it is in the desired position, lock it in

place using angle P and screw R.

Inserting the machine into the Cabinet.

- Push the machine into the opening, aligning it with the cabi-

nets (fig. 6).

- Regulate the adjustable feet to raise the machine to the

appropriate height.

- To adjust the position of the wooden panel in both the

vertical and horizontal directions, use the C and D screws, as

shown in fig. 7.

Important: close the lower part of the appliance front by

ensuring that the plinth rests against the floor.

Fig. 8 Fig. 9

Accessories provided for the height adjustment.

The following can be found inside the polystyrene lid (fig. 10): 2

crossbars (G), 1 strip (M)

the following can be found inside

the appliance drum:

4 additional feet (H),

4 screws (I),

4 screws (R),

4 nuts (L),

2 plinth guides (Q)

Adjusting the appliance height.

The height of the appliance can be adjusted (from 815 mm to

835 mm), by turning the 4 feet.

Should you require the appliance to be placed higher than the

above height, you need to use the following accessories to

raise it to up to 870 mm:

the two crossbars (G); the 4 feet (H); the 4 screws (I); the 4

nuts (L) then perform the following operations (fig. 11):

remove the 4 original feet, place a crossbar G at the front of the

appliance, fastening it in place using screws I (screwing them in

where the original feet were) then insert the new feet H.

Repeat the same operation at the back of the appliance.

Now adjust feet H to raise or lower the appliance from 835 mm

to 870 mm.

Once you have reached the desired height, lock nuts L onto

crossbar G.

To adjust the appliance to a height between 870 mm and 900

mm, you need to mount strip M, adjusting feet H to the requi-

red height.

Insert the strip as follows:

loosen the three screws N situated at the front of the Top cover

of the appliance, insert strip M as shown in fig. 12, then fasten

screws N.

D

C

570

min

815

540

595

820 ÷ 900

600 min

Fig. 6 Fig. 7

L

I

H

G

M

Fig. 11 Fig. 12

Fig. 10

6

GB

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents and

laundry”).

ON/OFF button : press this briefly to switch the ma-

chine on or off. The START/PAUSE indicator light, which

flashes slowly in a green colour shows that the machine is

switched on. To switch off the washing machine during the

wash cycle, press and hold the button for approximately 2

seconds; if the button is pressed briefly or accidentally the

machine will not switch off. If the machine is switched off

during a wash cycle, this wash cycle will be cancelled.

WASH CYCLE SELECTOR buttons: used to set the

desired wash cycle (see “Table of wash cycles”).

MEMORY button: press and hold the button to store a

cycle with your own set of preferences in the memory of

the machine. To recall a previously stored cycle, press the

MEMORY button.

FUNCTION buttons: press the button to select the

desired function. The corresponding indicator light on the

display will switch on.

SPIN button : press to reduce or completely exclude

the spin cycle - the value is indicated on the display.

TEMPERATURE button : press to decrease the tem-

perature: the value will be shown on the display.

CONTROL PANEL LOCK button : to activate

the control panel lock, press and hold the button for

approximately 2 seconds. When the symbol is

illuminated, the control panel is locked. This means it

is possible to prevent wash cycles from being modified

accidentally, especially where there are children in the

home. To deactivate the control panel lock, press and

hold the button for approximately 2 seconds.

DELAYED START button : press to set a delayed start

time for the selected wash cycle. The delay time will be

shown on the display.

START/PAUSE button with indicator light: when the gre-

en indicator light flashes slowly, press the button to start a

wash cycle. Once the cycle has begun the indicator light

will remain lit in a fixed manner. To pause the wash cycle,

press the button again; the indicator light will flash in an

orange colour. If the symbol is not illuminated, the door

may be opened. To start the wash cycle from the point at

which it was interrupted, press the button again.

Standby mode

This washing machine, in compliance with new energy sa-

ving regulations, is fitted with an automatic standby system

which is enabled after about 30 minutes if no activity is

detected. Press the ON-OFF button briefly and wait for the

machine to start up again.

Description of the washing

machine

SPIN SPEED

Button

START/PAUSE

button with indicator

light

Control panel

TEMPERATURE

Button

WASH

CYCLE

SELECTOR

Buttons

Detergent dispenser drawer

FUNCTION

buttons

ON/OFF

button

DISPLAY

DELAYED

START

Button

MEMORY

Button

CONTROL PANEL

LOCK button

GB

7

Display

The display is useful when programming the machine and provides a great deal of information.

The two upper strings A and B provide details of the wash cycle selected, the wash cycle phase in progress and all informa-

tion relating to the progress status of the wash cycle.

String C shows the time remaining until the end of the wash cycle in progress and, if a DELAYED START has been set, the

time remaining until the start of the selected wash cycle.

String D shows the maximum spin speed value (this depends on the selected wash cycle); if the wash cycle does not include

a spin cycle, the string remains unused.

String E shows the maximum temperature value which may be selected (this depends on the wash cycle used); if the tempe-

rature of the wash cycle cannot be modified, the string remains unused.

Indicator lights F correspond to the functions and light up when the selected function is compatible with the set wash cycle.

Door locked symbol

If the symbol is lit, this indicates that the washing machine door is blocked to prevent it from being opened accidentally. To

prevent any damage from occurring, wait for the symbol to switch itself off before opening the appliance door.

N.B.: if the DELAYED START function has been activated, the door cannot be opened; pauses the machine by pressing the

START/PAUSE button if you wish to open it.

! The first time the machine is switched on, you will be asked to select the language and the display will automatically show

the language selection menu.

To select the desired language press the X and Y buttons; to confirm the selection press the Z button.

To change the language switch off the machine and press buttons X, Y, Z simultaneously until an alarm is heard: the

language-selection menu will be displayed again.

A

B

C

D

E

Z

X

Y

START/PAUSE

button with indicator

light

F

8

GB

Running a wash cycle

1. SWITCH THE MACHINE ON. Press the button;

the text HELLO will appear on the display and the

START/PAUSE indicator light will flash slowly in a green

colour.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes on the following page.

3. MEASURE OUT THE DETERGENT. Pull out the

detergent dispenser drawer and pour the detergent into

the relevant compartments as described in “Detergents

and laundry”.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Press one of the WASH

CYCLE SELECTOR buttons to select the required wash

cycle; the name of the wash cycle will appear on the

display. A temperature and spin speed is set for each

wash cycle; these may be adjusted. The duration of the

cycle will appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons:

Modifying the temperature and/or spin

speed. The machine automatically selects the

maximum temperature and spin speed set for the

selected wash cycle; these values cannot therefore

be increased. The temperature can be decreased by

pressing the button, until the cold wash “OFF”

setting is reached. The spin speed may be progressively

reduced by pressing the button, until it is completely

excluded (the “OFF” setting). If these buttons are

pressed again, the maximum values are restored.

! Exception: if the (60°C)

(1st press of the button)

programme is selected, the temperature can be

increased up to a value of 90°C.

Setting a delayed start.

To set a delayed start for the selected programme,

press the corresponding button repeatedly until the

required delay period has been reached. When this

option is enabled, the symbol lights up on the

display. To remove the delayed start function press the

button until the text “OFF” appears on the display.

Modifying the cycle settings.

• Press the button to enable the function; the indicator

light corresponding to the button will switch on.

• Press the button again to disable the function; the

indicator light will switch off.

! If the selected function is not compatible with the

programmed wash cycle, the indicator light will flash

and the function will not be activated.

! If the selected function is not compatible with

another function which has been selected previously,

the indicator light corresponding to the first function

selected will flash and only the second function will

be activated; the indicator light corresponding to the

enabled function will remain lit.

! The functions may affect the recommended load value

and/or the duration of the cycle.

7. START THE PROGRAMME. Press the START/

PAUSE button. The corresponding indicator light will

become green, remaining lit in a fixed manner, and the

door will be locked (the DOOR LOCKED symbol will

be on). During the wash cycle, the name of the phase

in progress will appear on the display. To change a

wash cycle while it is in progress, pause the washing

machine using the START/PAUSE button (the START/

PAUSE indicator light will flash slowly in an orange

colour); then select the desired cycle and press the

START/PAUSE button again.

To open the door while a cycle is in progress, press

the START/PAUSE button; if the DOOR LOCKED

symbol is switched off the door may be opened. Press

the START/PAUSE button again to restart the wash

cycle from the point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This will be

indicated by the text “END OF CYCLE” on the display;

when the DOOR LOCKED symbol switches off

the door may be opened. Open the door, unload the

laundry and switch off the machine.

! If you wish to cancel a cycle which has already begun,

press and hold the button. The cycle will be stopped

and the machine will switch off.

GB

9

Wash cycles and functions

Wash functions

Super Wash

This option offers a high-

performance wash due to the

greater quantity of water used

in the initial phase of the cycle,

and due to the increased wash

cycle duration, is particular-

ly useful for the removal of

stubborn stains. It can be used

with or without bleach. If you

desire bleaching, insert the

extra tray compartment (4) into

compartment 1. When pouring

in the bleach, be careful not

to exceed the “max” level marked on the central pivot (see

figure). To bleach laundry without carrying out a full wash

cycle, pour the bleach into the extra compartment 4, select

the “Rinse” cycle and activate the “Super Wash” option.

! The use of extra compartment 4 excludes the “Pre-wash”

function.

! It cannot be used with the , , , , “Fast Spin Cottons”,

“Pump out”.

Extra Rinse

By selecting this option, the efficiency of the rinse is increased

and optimal detergent removal is guaranteed. It is particularly

useful for sensitive skin.

! It cannot be used with the “Fastwash 30’”, , , “Fast Spin

Cottons”, “Pump out”.

Table of wash cycles

Easy Iron

By selecting this function, the wash and spin cycles will be modified

in order to reduce the formation of creases. At the end of the cycle

the washing machine will perform slow rotations of the drum; the

EASY IRON and START/PAUSE indicator lights will flash (orange)

and the text “END OF CYCLE” will appear on the display. To end

the cycle, press the START/PAUSE button or the EASY IRON

button. To drain the water so that the laundry may be removed,

press the START/PAUSE button or the EASY IRON button.

! It cannot be used with the , “Fastwash 30’”, , , .

Prewash

If this function is selected, the pre-wash cycle will run; this is

useful for removing stubborn stains.

N.B.: put the detergent in the relevant compartment.

! It cannot be used with the , , , , ,

(60°), (40°),

.

Eco Wash

The Eco Wash function saves energy by not heating the

water used to wash your laundry – an advantage both to the

environment and to your energy bill. Instead, intensified wash

action and water optimisation ensure great wash results in the

same average time of a standard cycle.

For the best washing results we recommend the usage of a

liquid detergent.

! It cannot be used with the , , , , , .

M

AX

1

2

4

3

Wash cycles

Description of the wash cycle

Max. temp.

(°C)

Max. speed

(rpm)

Detergents

Max. load

(kg)

Residual dam-

pness %

Energy con-

sumption kWh

Total water lt

Cycle duration

Prewash

Wash

Fabric

softener

Bleach

Anti Stain

40° 1400

   

4 - -

-

180’

Standard Cotton 60° (1) (1st press of the button): heavily soiled whites and

delicate colours.

60°

(Max. 90°)

1400



(3)

  

7 53 1,10 52,5 190’

Standard Cotton 40° (2) (2nd press of the button): lightly soiled whites and

delicate colours.

40° 1400 -

  

7 53 0,99

82

185’

Standard Cotton 20° (3rd press of the button): lightly soiled whites and

delicate colours.

20° 1400 -

  

7 - -

-

170’

Synthetics Resistant (1st press of the button): heavily soiled resistant colours. 60° 800

   

3 44 0,93 47 110’

Synthetics Resistant (4) (1st press of the button): lightly soiled resistant colours. 40° 800

   

3 44 0,57 46 95’

Synthetics Delicate (2nd press of the button): lightly soiled resistant colours. 40° 800

   

3 - - - 70’

Fastwash 60' (1st press of the button): to refresh normal soiled garments quic-

kly (not suitable for wool, silk and clothes which require washing by hand).

60° 1400 -

 

- 3,5 53 0,81 40 60’

Fastwash 30' (2nd press of the button): to refresh lightly soiled garments quic-

kly (not suitable for wool, silk and clothes which require washing by hand).

30° 800 -

 

- 3 71 0,15 35 30’

M

My Cycle: allows for any wash cycle to be stored.

Anti Allergy

60° 1400 -

 

- 4 - - - 195’

Woolmark Platinum (Wool): for wool, cashmere, etc. 40° 800 -

 

- 1,5 - - - 70’

Delicates

30° 0 -

 

- 1 - - - 80’

Fast Spin Cottons (1st press of the button) - 1400 - - - - 7 - - - 16’

Rinse Cottons (2nd press of the button) - 1400 - -

 

7 - - - 36’

Pump out (3rd press of the button) - 0 - - - - 7 - - - 2’

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors

such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

1) Test wash cycle in compliance with directive 1061/2010: set wash cycle 60°C (1st press of the button).

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be

washed at 60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with directive 1061/2010: set wash cycle 40°C (2nd press of the button).

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be

washed at 40°C. The actual washing temperature may differ from the indicated value.

3) At 60 °C the “Prewash” function cannot be selected.

For all Test Institutes:

2) Long wash cycle for cottons: set wash cycle 40°C (2nd press of the button).

4) Long wash cycle for synthetics: set wash cycle 60°C (1st press of the button); temperature of 40°C (press TEMPERATURE button).

10

GB

Detergent dispenser drawer

Good washing results also depend on the correct dose of

detergent: adding too much detergent will not necessa-

rily result in a more efficient wash, and may in fact cause

build up on the inside of your appliance and contribute to

environmental pollution.

! Use powder detergent for white cotton garments, for

pre-washing, and for washing at temperatures over 60°C.

! Follow the instructions given on the detergent packaging.

! Do not use hand washing detergents because these

create too much foam.

Open the detergent di-

spenser drawer and pour

in the detergent or washing

additive, as follows.

compartment 1: Pre-wash detergent (powder)

Before pouring in the detergent, make sure that extra com-

partment 4 has been removed.

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in immediately

prior to the start of the wash cycle.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

extra compartment 4: Bleach

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites

• Empty all garment pockets and check the buttons.

• Do not exceed the listed values, which refer to the

weight of the laundry when dry: see “Table of wash

cycles”.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Special wash cycles

Anti Stain : this programme is suitable to heavily-soiled

garments with resistant colours. It ensures a washing

class that is higher than the standard class (A class). When

running the programme, do not mix garments of different

colours. We recommend the use of powder detergent.

Pre-treatment with special additives is recommended if

there are obstinate stains.

Standard Cotton 20°: ideal for lightly soiled cotton loads.

The effective performance levels achieved at cold tempe-

ratures, which are comparable to washing at 40°, are gua-

ranteed by a mechanical action which operates at varying

speed, with repeated and frequent peaks.

Anti Allergy: use programme to remove major allergens

such as pollen, mites, cat’s and dog’s hair.

Wool: the wool wash cycle on this Hotpoint/Ariston ma-

chine has been tested and approved by The Woolmark

Company for washing wool garments labelled as hand wa-

shable provided that the garments are washed according

to the instructions on the garment label and those issued

by the manufacturer of this washing machine. Hotpoint/

Ariston is the first washing machine brand to be approved

by The Woolmark Company for Apparel Care- Platinum for

its washing performance and consumption of energy and

water. (M1126)

Delicates: use programme to wash very delicate

garments with decorative features, such as diamantes and

sequins.

We recommend turning the garments inside out before

washing and placing small items into the special bag

for washing delicates. Use liquid detergent on delicate

garments for best results.

To wash Silk garments and Curtains, select cycle and

then function (in this case it will also be possible

to enable the “Extra Rinse” function); the machine will

end the cycle while the laundry is soaking and the

indicator light will flash. To drain the water so that the

laundry may be removed, press the START/PAUSE button

or the button.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and

to distribute the load in a uniform manner, the drum rotates

continuously at a speed which is slightly greater than the

washing rotation speed. If, after several attempts, the load

is not balanced correctly, the machine spins at a reduced

spin speed. If the load is excessively unbalanced, the

washing machine performs the distribution process instead

of spinning. To encourage improved load distribution and

balance, we recommend small and large garments are

mixed in the load.

Detergents and laundry

M

AX

1

2

4

3

GB

11

Precautions and tips

! This washing machine was designed and constructed in

accordance with international safety regulations. The fol-

lowing information is provided for safety reasons and must

therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance is not intended for use by persons (inclu-

ding children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concer-

ning use of the appliance by a person responsible for

their safety. Children should be supervised to ensure that

they do not play with the appliance.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not open the detergent dispenser drawer while the

machine is in operation.

• Do not touch the drained water as it may reach extreme-

ly high temperatures.

• Never force the porthole door. This could damage the safety

lock mechanism designed to prevent accidental opening.

• If the appliance breaks down, do not under any circum-

stances access the internal mechanisms in an attempt

to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make

sure the drum is empty.

Disposal

• Disposing of the packaging materials: observe local regu-

lations so that the packaging may be re-used.

• The European Directive 2012/19/EU on Waste Electrical

and Electronic Equipment, requires that old household

electrical appliances must not be disposed of in the normal

unsorted municipal waste stream. Old appliances must be

collected separately in order to optimise the recovery and

recycling of the materials they contain and reduce the im-

pact on human health and the environment. The crossed

out “wheeled bin” symbol on the product reminds you of

your obligation, that when you dispose of the appliance it

must be separately collected. Consumers should contact

their local authority or retailer for information concerning the

correct disposal of their old appliance.

Opening the porthole door manually

In the event that it is not possible to open the porthole

door due to a powercut, and if you wish to remove the

laundry, proceed as follows:

1. remove the plug from the electrical socket.

2. make sure the water level inside the machine is lower

than the door opening; if it is not, remove excess water

using the drain hose, collecting it in a bucket as indicated

in the figure.

3. pull outwards using the tab as indicated in the figure,

until the plastic tie-rod is freed from its stop position; pull

downwards and open the door at the same time.

12

GB

Care and maintenance

Cutting off the water and electricity

supplies

• Turn off the water tap after every wash cycle. This will limit

wear on the hydraulic system inside the washing machine

and help to prevent leaks.

• Unplug the washing machine when cleaning it and du-

ring all maintenance work.

Cleaning the washing machine

The outer parts and rubber components of the appliance

can be cleaned using a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser dra-

wer

Remove the dispenser by

raising it and pulling it out

(see figure).

Wash it under running wa-

ter; this operation should be

repeated frequently.

Caring for the door and drum of your

appliance

• Always leave the porthole door ajar in order to prevent

unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning pump

which does not require any maintenance. Sometimes,

small items (such as coins or buttons) may fall into the pre-

chamber which protects the pump, situated in its bottom

part.

! Make sure the wash cycle has finished and unplug the

appliance.

To access the pre-chamber:

1. unscrew the lid by rota-

ting it anti-clockwise (see

figure): a little water may

trickle out. This is perfectly

normal;

2. clean the inside thoroughly;

3. screw the lid back on;

Checking the water inlet hose

Check the inlet hose at least once a year. If there are any

cracks, it should be replaced immediately: during the wash

cycles, water pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

1

2

GB

13

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure

that the problem cannot be solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not

take in water (the text “NO WATER,

CHECK SUPPLY” appears on the

display).

The washing machine continuously

takes in and

drains water.

The washing machine does not

drain or spin.

The washing machine vibrates a lot

during the spin cycle.

The washing machine leaks.

The machine is locked and the display

flashes, indicating an error code (e.g.

F-01, F-..).

There is too much foam.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or is not making contact.

• There is no power in the house.

• The washing machine door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set (see “Running a wash cycle”).

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

• The free end of the hose is under water (see “Installation”).

• The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch

the appliance off and contact the Assistance Service. If the dwelling is on one of

the upper floors of a building, there may be problems relating to water drainage,

causing the washing machine to fill with water and drain continuously. Special

anti-draining valves are available in shops and help to avoid this inconvenience.

• The wash cycle does not include draining: some wash cycles require the drain

phase to be started manually (see “Wash cycles and functions”).

• The EASY IRON function has been activated: To complete the wash cycle,

press the START/PAUSE button (see “Wash cycles and functions”).

• The drain hose is bent (see “Installation”).

• The drainage duct is clogged.

• The drum was not unlocked correctly during installation (see “Installation”).

• The washing machine is not level (see “Installation”).

• The washing machine is trapped between cabinets and walls (see “Installation”).

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser drawer is blocked (for cleaning instructions, see

“Care and maintenance”).

• The drain hose is not fixed properly (see “Installation”).

• Switch off the machine and unplug it, wait for approximately 1 minute and

then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

• The detergent is not suitable for machine washing (it should display the text

“for washing machines” or “hand and machine wash”, or the like).

• Too much detergent was used.

14

GB

Service

Before calling for Assistance:

• Check whether you can solve the problem alone (see “Troubleshooting”);

• Restart the programme to check whether the problem has been solved;

• If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the

guarantee certificate.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• the type of problem;

• the appliance model (Mod.);

• the serial number (S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the

front of the appliance by opening the door.

15

I

Italiano

Sommario

Installazione, 16-17-18-19

Disimballo e livellamento

Collegamenti idraulici ed elettrici

Primo ciclo di lavaggio

Dati tecnici

Istruzioni per l’installatore

Descrizione della lavabiancheria, 20-21

Pannello di controllo

Display

Come effettuare un ciclo di lavaggio, 22

Programmi e funzioni, 23

Tabella dei programmi

Funzioni di lavaggio

Detersivi e biancheria, 24

Cassetto dei detersivi

Preparare la biancheria

Programmi particolari

Sistema bilanciamento del carico

Precauzioni e consigli, 25

Sicurezza generale

Smaltimento

Apertura manuale della porta oblò

Manutenzione e cura, 26

Escludere acqua e corrente elettrica

Pulire la lavabiancheria

Pulire il cassetto dei detersivi

Curare oblò e cestello

Pulire la pompa

Controllare il tubo di alimentazione dell’acqua

Anomalie e rimedi, 27

Assistenza, 28

Assistenza Attiva 7 giorni su 7

I

LAVABIANCHERIA

BWMD 742

Istruzioni per l’uso

16

I

! È importante conservare questo libretto per poterlo con-

sultare in ogni momento. In caso di vendita, di cessione o

di trasloco, assicurarsi che resti insieme alla lavabiancheria

per informare il nuovo proprietario sul funzionamento e sui

relativi avvertimenti.

! Leggere attentamente le istruzioni: ci sono importanti

informazioni sull’installazione, sull’uso e sulla sicurezza.

Disimballo e livellamento

Disimballo

1. Disimballare la lavabiancheria.

2. Controllare che la lavabiancheria non abbia

subìto danni nel trasporto. Se fosse danneggiata

non collegarla e contattare il rivenditore.

3. Rimuovere le 4 viti di

protezione per il trasporto

e il gommino con il relativo

distanziale, posti nella parte

posteriore (vedi figura).

4. Chiudere i fori con i tappi di plastica in dotazione.

5. Conservare tutti i pezzi: qualora la lavabiancheria debba

essere trasportata, dovranno essere rimontati.

! Gli imballaggi non sono giocattoli per bambini.

Livellamento

1. Installare la lavabiancheria su un pavimento piano e rigi-

do, senza appoggiarla a muri, mobili o altro.

2. Se il pavimento non fosse

perfettamente orizzontale,

compensare le irregolarità

svitando o avvitando i piedini

anteriori (vedi figura); l’ango-

lo di inclinazione, misurato

sul piano di lavoro, non deve

superare i 2°.

Un accurato livellamento dà stabilità alla macchina ed

evita vibrazioni, rumori e spostamenti durante il funzio-

namento. In caso di moquette o di un tappeto, regolare i

piedini in modo da conservare sotto la lavabiancheria uno

spazio sufficiente per la ventilazione.

Collegamenti idraulici ed elettrici

Collegamento del tubo di alimentazione dell’acqua

1. Collegare il tubo di

alimentazione avvitandolo

a un rubinetto d’acqua

fredda con bocca filettata

da 3/4 gas (vedi figura).

Prima di allacciare, far

scorrere l’acqua finché

non sia limpida.

2. Collegare il tubo di ali-

mentazione alla lavabian-

cheria avvitandolo all’ap-

posita presa d’acqua,

nella parte posteriore in

alto a destra (vedi figura).

3. Fare attenzione che nel tubo non ci siano né pieghe né

strozzature.

! La pressione idrica del rubinetto deve essere compresa

nei valori della tabella Dati tecnici

(vedi pagina a fianco).

! Se la lunghezza del tubo di alimentazione non fosse

sufficiente, rivolgersi a un negozio specializzato o a un

tecnico autorizzato.

! Non utilizzare mai tubi già usati.

! Utilizzare quelli in dotazione alla macchina.

Installazione

17

I

Collegamento del tubo di scarico

Collegare il tubo di scari-

co, senza piegarlo, a una

conduttura di scarico o a

uno scarico a muro posti

tra 65 e 100 cm da terra;

oppure appoggiarlo al

bordo di un lavandino o

di una vasca, legando la

guida in dotazione al

rubinetto (vedi figura).

L’estremità libera del tubo

di scarico non deve rima-

nere immersa nell’acqua.

! È sconsigliato usare tubi di prolunga; se indispensabile,

la prolunga deve avere lo stesso diametro del tubo origi-

nale e non superare i 150 cm.

Collegamento elettrico

Prima di inserire la spina nella presa della corrente, accer-

tarsi che:

• la presa abbia la messa a terra e sia a norma

di legge;

• la presa sia in grado di sopportare il carico

massimo di potenza della macchina, indicato nella

tabella Dati tecnici (vedi a fianco);

• la tensione di alimentazione sia compresa nei

valori indicati nella tabella Dati tecnici (vedi a

fianco);

• la presa sia compatibile con la spina della

lavabiancheria. In caso contrario sostituire la

presa o la spina.

! La lavabiancheria non va installata all’aperto, nemmeno

se lo spazio è riparato, perché è molto pericoloso lasciar-

la esposta a pioggia e temporali.

! A lavabiancheria installata, la presa della corrente deve

essere facilmente raggiungibile.

! Non usare prolunghe e multiple.

! Il cavo non deve subire piegature o compressioni.

! Il cavo di alimentazione deve essere sostituito solo da

tecnici autorizzati.

Attenzione! L’azienda declina ogni responsabilità qualora

queste norme non vengano rispettate.

Primo ciclo di lavaggio

Dopo l’installazione, prima dell’uso, effettuare un ciclo di

lavaggio con detersivo e senza biancheria impostando il

programma

(60° C).

65 - 100 cm

Dati tecnici

Modello

BWMD 742

Dimensioni

larghezza cm 59,5

altezza cm 81,5

profondità cm 54,5

Capacità

da 1 a 7 kg

Collegamenti

elettrici

Vedi targhetta caratteristiche tecniche

applicata sulla macchina

Collegamenti

idrici

pressione massima 1 MPa (10 bar)

pressione minima 0,05 MPa (0,5 bar)

capacità del cesto 52 litri

Velocità di cen-

trifuga

sino a 1400 giri al minuto

Programmi di

prova

secondo la

direttive

1061/2010 e

1015/2010

programma

(60°) (1° pressione del tasto);

Cotone standard 60°C.

programma

(40°) (2° pressione del tasto);

Cotone standard 40°C.

Questa apparecchiatura è conforme alle

seguenti Direttive Comunitarie:

- 2004/108/CE (Compatibilità

Elettromagnetica)

- 2006/95/CE (Bassa Tensione)

- 2012/19/EU

18

I

Istruzioni per l’installatore

Applicazione del pannello in legno alla porta e inse-

rimento della macchina nei mobili:

Nel caso in cui, dopo il montaggio del pannello in legno, sia

necessario spedire la macchina per l’installazione finale,

consigliamo di lasciarla nel suo imballo originale. A questo

scopo l’imballo è stato realizzato in modo da permettere il

montaggio del pannello di legno sulla macchina senza disim-

ballare completamente il prodotto (vedi figure sottostanti).

Il pannello di legno che copre la facciata non deve essere di

spessore inferiore a 18 mm e può essere incernierato sia sul

lato destro che sinistro. Per ragioni di praticità d’uso della

macchina consigliamo lo stesso senso di apertura dell’oblò

con le cerniere applicate sul lato sinistro.

A

B

C

D

E

Tur seite

Accessori montaggio portina (Fig. 1-2-3-4-5).

Fig. 1

N° 2 cerniere

N° 1 Magnete N° 1 Riscontro magnete

N° 1 Tassello in gomma

N° 2 Supporti cerniera

N° 4 Distanziali

Fig. 2

Fig. 3 Fig. 4

Fig. 5

Fig. 4/B

- n° 6 viti autofilettanti l = 13 mm “tipo A”.

- n° 2 viti metriche testa svasata l = 25 mm “tipo B”; per il

fissaggio del riscontro magnete al mobile.

- n° 4 viti metriche l = 15 mm “tipo C”; per il montaggio dei

supporti cerniera al mobile.

- n° 4 viti metriche l = 7 mm “tipo D”; per il montaggio delle

cerniere ai supporti.

Montaggio dei particolari sulla facciata della macchina.

- Montare i supporti cerniera alla facciata posizionando il

foro indicato da una freccia nella fig. 1 verso l’interno della

facciata interponendo un distanziale (fig. 4/B), utilizzando le

viti tipo C.

- Montare il riscontro magnete dalla parte opposta in alto

interponendo due distanziali (fig. 4/B) utilizzando le due viti

tipo B.

19

I

Uso della maschera di foratura.

- Per tracciare le posizioni dei fori sul lato sinistro del pan-

nello, allinerare la maschera di foratura al lato superiore e

sinistro del pannello facendo riferimento alle linee tracciate

alle estremità.

- Per tracciare le posizioni dei fori sul lato destro del pannel-

lo, allinerare la maschera di foratura al lato superiore e destro

del pannello.

- Con una fresa di adeguate dimensioni realizzare le quattro

sedi che dovranno alloggiare le due cerniere, il tassello di

gomma e il magnete.

Montaggio dei particolari sul pannello di legno (Antina).

- Inserire le cerniere nelle sedi predisposte (la parte mobile

della cerniera deve trovarsi verso l’esterno del pannello) e

fissarle con 4 viti del tipo A.

- Inserire il magnete nella sede in alto dalla parte opposta

alle cerniere e fissarlo con due viti tipo B.

- Inserire il tassello in gomma nella sede in basso.

Il pannello è ora pronto per essere montato sulla macchina.

Montaggio del pannello alla macchina.

Inserire il nasello della cerniera indicato dalla freccia nella fig.

2 nella sede del supporto cerniera spingere il pannello verso

la facciata della macchina e fissare le due cerniere con le

due viti tipo D.

Fissaggio della guida zoccolo.

Se la macchina è installata ad una estremità della cucina

componibile montare una o entrambe le guide zoccolo

come indicato in fig. 8, regolandone la profondità in funzione

della posizione dello zoccolo e se necessario fissarlo alle

stesse (fig. 9).

Per montare la guida zoccolo agire cone segue (fig. 8):

Fissare la squadretta P con la vite R, infilare la guida zoccolo

Q nell’apposita asola e una volta posizionata nel punto desi-

derato bloccarla alla squadretta P con la vite R.

Inserimento della macchina nei mobili.

- Spingere l’apparecchio nell’apertura allineandola con gli

altri mobili (fig. 6).

- Agire sui piedini di regolazione per portare la macchina

all’altezza desiderata.

- Per regolare la posizione del pannello in legno in senso

verticale ed orizzontale, agire sulle viti C e D come indicato

in fig. 7.

Importante: chiudere la parte inferiore della facciata con lo

zoccolo a battuta sul pavimento.

Fig. 8 Fig. 9

Accessori in dotazione per la regolazione in altezza.

Alloggiate nel coperchio di polistirolo (fig. 10) si trovano:

2 traverse (G); 1 listello (M)

all’interno del cestello si trovano:

4 piedini supplementari (H)

4 viti (I)

4 viti (R)

4 dadi (L)

2 guide zoccolo (Q)

Regolazione in altezza della macchina.

La macchina può essere regolata in altezza (da 815 mm a 835

mm) agendo sui 4 piedini.

Se si desidera portarla ad un’altezza superiore a quella soprain-

dicata, arrivando fino a 870 mm, occorre utilizzare i seguenti

accessori:

le 2 traverse (G); i 4 piedini (H); le 4 viti (I); i 4 dadi (L), quindi

agire come segue (fig. 11):

togliere i 4 piedini originali, posizionare una traversa G nella par-

te anteriore della macchina, fissarla con le viti I (avvitandole nei

fori dove erano montati i piedini originali) quindi inserire i nuovi

pedini H.

Ripetere la stessa operazione nella parte posteriore della macchina.

A questo punto regolando i piedini H la macchina può essere

abbassata o alzata da 835 mm a 870 mm.

Una volta raggiunta l’altezza desiderata bloccare i dadi L alla

traversa G.

Per regolare la macchina ad un’altezza compresa tra 870 mm e

900 mm occorre montare il listello M regolando i piedini H fino

all’altezza desiderata. Per inserire il listello agire come segue:

allentare le tre viti N poste nella parte anteriore della copertu-

ra Top, inserire il listello M come indicato nella fig. 12, quindi

bloccare le viti N.

D

C

570

min

815

540

595

820 ÷ 900

600 min

Fig. 6 Fig. 7

L

I

H

G

M

Fig. 11 Fig. 12

Fig. 10

20

I

Descrizione della lavabiancheria

Cassetto dei detersivi: per caricare detersivi e additivi

(vedi “Detersivi e biancheria”).

Tasto ON/OFF : premere brevemente il tasto per ac-

cendere o spegnere la macchina. La spia START/PAUSE

che lampeggia lentamente di colore verde indica che la

macchina è accesa. Per spegnere la lavabiancheria du-

rante il lavaggio è necessario tenere premuto il tasto più

a lungo, circa 2 sec.; una pressione breve o accidentale

non permetterà lo spegnimento della macchina.

Lo spegnimento della macchina durante un lavaggio in

corso annulla il lavaggio stesso.

Tasti SELETTORE PROGRAMMI: per impostare il pro-

gramma desiderato (vedi “Tabella dei programmi”).

Tasto MEMO: tenere premuto il tasto per memorizzare

un ciclo e le proprie personalizzazioni preferite. Per richia-

mare un ciclo precedentemente memorizzato premere il

tasto MEMO.

Tasti FUNZIONE: premere il tasto per selezionare la fun-

zione desiderata. Sul display si illuminerà la spia relativa.

Tasto CENTRIFUGA : premere per ridurre o escludere

del tutto la centrifuga; il valore viene indicato nel display.

Tasto TEMPERATURA : premere per ridurre la tem-

peratura; il valore viene indicato nel display.

Tasto BLOCCO TASTI : per attivare il blocco del

pannello di controllo, tenere premuto il tasto per circa

2 secondi. Il simbolo acceso indica che il pannello

di controllo è bloccato. In questo modo si impediscono

modifiche accidentali dei programmi, soprattutto se in

casa ci sono dei bambini.

Per disattivare il blocco del pannello di controllo, tenere

premuto il tasto per circa 2 secondi.

Tasto PARTENZA RITARDATA : premere per impo-

stare una partenza ritardata del programma prescelto; il

ritardo viene indicato nel display.

Tasto con spia START/PAUSE: quando la spia verde

lampeggia lentamente, premere il tasto per avviare un

lavaggio. A ciclo avviato la spia diventa fissa. Per mettere

in pausa il lavaggio, premere nuovamente il tasto; la spia

lampeggerà con colore arancione. Se il simbolo non è

illuminato, si potrà aprire l’oblò. Per far ripartire il lavaggio

dal punto in cui è stato interrotto, premere nuovamente il

tasto.

Modalità di stand by

Questa lavatrice, in conformità alle nuove normative

legate al risparmio energetico, è dotata di un sistema

di autospegnimento (stand by) che entra in funzione

dopo circa 30 minuti nel caso di non utilizzo. Premere

brevemente il tasto ON/OFF e attendere che la macchina

si riattivi.

Tasto con spia

START/

PAUSE

Tasto

TEMPERATURA

Tasto

CENTRIFUGA

Pannello di controllo

Tasto

BLOCCO

TASTI

Tasti

FUNZIONE

Tasto ON/OFF

Tasto

MEMO

Tasto

PARTENZA

RITARDATA

Tasti

SELETTORE

PROGRAMMI

Cassetto dei detersivi

DISPLAY

Страница загружается ...

HOTPOINT/ARISTON BWMD 742 (EU) Руководство пользователя

HOTPOINT/ARISTON BWMD 742 (EU) Руководство пользователя

на других языках

Похожие модели бренда

Модели других брендов