Pioneer MVH-09UBG Руководство пользователя

Бренд: Pioneer

Модель: MVH-09UBG

Категория: Мультимедиа-приемники для автомобилей

Тип: Руководство пользователя

H:\PDF-OUT\127075007251\010COV_KM686UW.fm

English Русский

MVH-09UB/MVH-09UBG

127075007251_(B6_Horizon)

DIGITAL MEDIA RECEIVER

ЦИФРОВОЙ МЕДИАРЕСИВЕР

MVH-09UB

MVH-09UBG

Owner’s Manual

Руководство пользователя

_127075007251_artwork.book Page 1 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\020Chapter_EN.fm

MVH-09UB/MVH-09UBG

127075007251

Before You Start ......................................................................... 2

Getting Started .......................................................................... 3

Radio ............................................................................................ 5

USB/AUX ...................................................................................... 5

Settings........................................................................................ 7

FUNCTION settings .................................................................. 7

AUDIO settings.......................................................................... 7

SYSTEM settings ....................................................................... 8

Connections/Installation.......................................................... 9

Additional Information........................................................... 12

About this manual:

• In the following instructions, a USB memory or USB audio player are referred

to as “USB device”.

Table of Contents

Thank you for purchasing this PIONEER product

To ensure proper use, please read through this manual before using this product. It is

especially important that you read and observe WARNINGs and CAUTIONs in this manual.

Please keep the manual in a safe and accessible place for future reference.

Private households in the member states of the EU, in Switzerland and Norway may return

their used electronic products free of charge to designated collection facilities or to a

retailer (if you purchase a similar new one).

For countries not mentioned above, please contact your local authorities for the correct

method of disposal.

By doing so you will ensure that your disposed product undergoes the necessary treatment,

recovery and recycling and thus prevent potential negative effects on the environment and

human health.

WARNING

•Do not attempt to install or service this product by yourself. Installation or servicing

of this product by persons without training and experience in electronic equipment

and automotive accessories may be dangerous and could expose you to the risk of

electric shock, injury or other hazards.

• Do not attempt to operate the unit while driving. Make sure to pull off the road and park

your vehicle in a safe location before attempting to use the controls on the device.

CAUTION

• Do not allow this unit to come into contact with moisture and/or liquids. Electrical shock

could result. Also, damage to this unit, smoke, and overheating could result from contact

with liquids.

• Always keep the volume low enough to hear outside sounds.

Before You Start

If you want to dispose this product, do not mix it with general household waste. There is a

separate collection system for used electronic products in accordance with legislation

that requires proper treatment, recovery and recycling.

_127075007251_artwork.book Page 2 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\020Chapter_EN.fm

MVH-09UB/MVH-09UBG

127075007251

English

If you experience problems

Should this unit fail to work properly, please contact your dealer or nearest authorized

PIONEER Service Station.

MVH-09UB/09UBG

Frequently used operations

Getting Started

Basic operation

Purpose Operation

Turn on the power* Press SRC/OFF to turn on the power.

Press and hold SRC/OFF to turn off the

power.

Adjust the volume Turn the M.C. dial.

Select a source Press SRC/OFF repeatedly.

Change the display information Press DISP repeatedly.

SRC (source)/OFF

Detach button

Display window

M.C. (multi-control) dial

BAND/DIMMER

DISP (display)

* When this unit’s blue/white lead is connected to the vehicle’s auto-antenna relay control

terminal, the vehicle’s antenna extends when this unit’s source is turned on. To retract the

antenna, turn the source off.

Display indication

Detach the front panel to prevent theft. Remove any cables and devices

attached to the front panel and turn off the unit before detaching it.

Important

• Avoid subjecting the front panel to excessive shock.

Return to the previous display/list Press BAND/DIMMER .

Return to the normal display from the

Press and hold BAND/DIMMER .

Indication Description

Appears when a lower tier of the menu or folder exists.

Appears when the button is pressed.

Appears when the local seek tuning function is set (page 7).

Appears when random/shuffle play is set.

Appears when repeat play is set.

Detaching the front panel

Purpose Operation

Detach Attach

_127075007251_artwork.book Page 3 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\020Chapter_EN.fm

MVH-09UB/MVH-09UBG

127075007251

• Keep the front panel out of direct sunlight and high temperatures.

• Always store the detached front panel in a protective case or bag.

When you turn the ignition switch to ON after installation, [SET UP :YES]

appears in the display.

1 Press the M.C. dial.

The setup menu disappears after 30 seconds of no operation. If you prefer

not to set at this time, turn the M.C. dial to select [NO], then press to

confirm.

2 Turn the M.C. dial to select the options, then press to confirm.

To proceed to the next menu option, you need to confirm your selection.

3 [QUIT :YES] appears when all the settings have been made.

To return to the first item of the setup menu, turn the M.C. dial to select

[QUIT :NO], then press to confirm.

4 Press the M.C. dial to confirm the settings.

NOTES

• You can cancel the menu setting by pressing SRC/OFF.

• These settings can be made at any time from the SYSTEM settings (page 8) and INITIAL

settings (page 4).

Setup menu

Menu Item Description

LANGUAGE Select the language to display the text

information from a compressed audio file.

[ENG](English),

[РУС](Russian),

[TUR](Turkish)

CLOCK SET Set the clock.

FM STEP Select the FM tuning step from 100 kHz or 50 kHz.

[100], [50]

1 Press the M.C. dial to display the main menu.

2 Turn the M.C. dial to select [SYSTEM], then press to confirm.

3 Turn the M.C. dial to select [DEMO OFF], then press to confirm.

4 Turn the M.C. dial to select [YES], then press to confirm.

1 Press and hold SRC/OFF until the unit turns off.

2 Press the M.C. dial to display the main menu.

3 Turn the M.C. dial to select [INITIAL], then press to confirm.

4 Turn the M.C. dial to select an option, then press to confirm.

NOTE

The options vary depending on the unit.

Canceling the demonstration display (DEMO

OFF)

INITIAL settings

Menu Item Description

FM STEP Select the FM tuning step from 100 kHz or 50 kHz.

[100], [50]

_127075007251_artwork.book Page 4 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\020Chapter_EN.fm

MVH-09UB/MVH-09UBG

127075007251

English

The RDS (radio data system) function only works in areas that broadcast RDS

signals for FM stations.

1 Press SRC/OFF to select [RADIO].

2 Press BAND/DIMMER to select the band from [F1], [FM2], [FM3],

[MW] or [LW].

TIP

F1 is for advanced FM band.

SP-P/O MODE Select when there is a full-range speaker connected to

the rear speaker output leads and there is a subwoofer

connected to the RCA output.

[REAR/SUB.W]

[SUB.W/SUB.W] Select when there is a passive subwoofer connected

directly to the rear speaker output leads and there is a

subwoofer connected to the RCA output.

[REAR/REAR] Select when there are full-range speakers connected to

the rear speaker output leads and RCA output. If there is

a full-range speaker connected to the rear speaker

output leads, and the RCA output is not used, you may

select either [REAR/SUB.W] or [REAR/REAR].

DIM SETTING Change the display brightness.

[SYNC CLOCK],

[MANUAL]

SYSTEM RESET Select [YES] to initialize the unit settings. The unit will be

restarted automatically.

(Some of the settings may be retained even after

resetting the unit.)

[YES], [CANCEL]

Radio

Receiving preset stations

Menu Item Description

3 Press a number button (1/ to 6/).

TIP

The / buttons can be also used to select a preset station when [SEEK] is set to

[PCH] in the FUNCTION settings (page 7).

The six strongest stations are stored on the number buttons (1/ to 6/).

1 After selecting the band, press the M.C. dial to display the main menu.

2 Turn the M.C. dial to select [FUNCTION], then press to confirm.

3 Turn the M.C. dial to select [BSM], then press to confirm.

To seek a station manually

After selecting the band, press / to select a station.

Press and hold / then release to seek an available station.

Scanning stops when the unit receives a station. To cancel seek tuning,

press / .

NOTE

[SEEK] needs to be set to [MAN] in the FUNCTION settings (page 7).

To store stations manually

While receiving the station you want to store, press and hold one of the

number buttons (1/ to 6/ ) until it stops flashing.

Disconnect headphones from the device before connecting it to the unit.

Best stations memory (BSM)

USB/AUX

Playing back

_127075007251_artwork.book Page 5 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\020Chapter_EN.fm

MVH-09UB/MVH-09UBG

127075007251

USB devices (including Android)

Open the USB port cover.

2 Plug in the USB.

NOTE

To automatically switch to [USB] source when a USB device is connected to the unit, set

[USB AUTO] to [ON] in the SYSTEM settings (page 9).

CAUTION

Use an optional Pioneer USB cable (CD-U50E) to connect the USB device as any device

connected directly to the unit will protrude out from the unit, which could be dangerous.

Before removing the device, stop playback.

AOA connections

A device installed with Android OS 5.0 or later can be connected to the unit via

AOA, using the cable supplied with the device.

This function is compatible with devices that have Android OS 5.0 or later

installed and also support AOA (Android Open Accessory) 2.0.

1 Press SRC/OFF to select [ANDROID].

Listening to music on Android

AUX input jack (3.5 mm stereo jack)

USB port

SRC (source)/OFF

M.C. (multi-control) dial

NOTE

Some Android devices connected via AOA 2.0 may not work properly or emit sounds due to

their own software design, regardless of the OS version.

Basic operations

AUX

Insert the stereo mini plug into the AUX input jack.

2 Press SRC/OFF to select [AUX] as the source.

NOTE

If [AUX] is set to [OFF] in the SYSTEM settings, [AUX] cannot be selected as a source (page 8).

You can make various adjustments in the FUNCTION settings (page 7).

Note that the following operations do not work for an AUX device. To operate

an AUX device, use the device itself.

Purpose Operation

Select a track Press or .

Fast forward or reverse Press and hold or .

Pause/resume playback Press 4/PAUS E.

Operations

Purpose Operation

Select a folder/album* Press 1/ or 2/.

Select a track/song (chapter) Press or .

Fast forward or reverse Press and hold or .

_127075007251_artwork.book Page 6 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\020Chapter_EN.fm

MVH-09UB/MVH-09UBG

127075007251

English

* Compressed audio files only

You can adjust various settings in the main menu.

1 Press the M.C. dial to display the main menu.

2 Turn the M.C. dial to select one of the categories below, then press to

confirm.

• FUNCTION settings (page 7)

• AUDIO settings (page 7)

• SYSTEM settings (page 8)

3 Turn the M.C. dial to select the options, then press to confirm.

Search for a file from a list 1 Press to display the list.

2 Turn the M.C. dial to select the

desired file (folder) name or

category, then press to confirm.

3 Turn the M.C. dial to select the

desired file, then press to confirm.

Playback starts.

View a list of the files in the selected

folder/category*

Press the M.C. dial when a folder/

category is selected.

Play a song in the selected folder/

category*

Press and hold the M.C. dial when a

folder/category is selected.

Repeat play Press 6/.

Random/shuffle play Press 5/.

Pause/resume playback Press 4/PAUSE.

Settings

Purpose Operation

The menu items vary according to the source.

FUNCTION settings

Menu Item Description

BSM

Store the six strongest stations on the

number buttons (1/ to 6/)

automatically.

LOCAL

F1/FM: [OFF], [LV1], [LV2],

[LV3], [LV4]

MW/LW: [OFF], [LV1], [LV2]

Restrict the tuning station according to the

signal strength.

SEEK

[MAN], [PCH] Assign or buttons to seek the

stations one by one (manual tuning) or

select a station from the preset channels.

AUDIO settings

Menu Item Description

FADER*1

Adjust the front and rear speaker balance.

BALANCE

Adjust the left and right speaker balance.

_127075007251_artwork.book Page 7 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\020Chapter_EN.fm

MVH-09UB/MVH-09UBG

127075007251

EQ SETTING

[SUPER BASS], [POWERFUL],

[NATURAL], [VOCAL],

[CUSTOM1], [CUSTOM2],

[FLAT]

Select an equalizer band and

level for further customizing.

Equalizer band: [80HZ],

[250HZ], [800HZ], [2.5KHZ],

[8KHZ]

Equalizer level: [+6] to [–6]

You can also switch the equalizer by

pressing repeatedly.

LOUDNESS

[OFF], [LOW], [MID], [HI] Compensate for clear sound at low volume.

SUB.W*2

[NOR], [REV], [OFF] Select the subwoofer phase.

SUB.W CTRL*2*3

Cut-off frequency: [50HZ],

[63HZ], [80HZ], [100HZ],

[125HZ], [160HZ], [200HZ]

Output level: [–24] to [+6]

Slope level: [–12], [–24]

Only frequencies lower than those in the

selected range are output from the

subwoofer.

BASS BOOST

[0] to [+6] Select the bass boost level.

HPF SETTING

Cut-off frequency: [OFF],

[50HZ], [63HZ], [80HZ],

[100HZ], [125HZ], [160HZ],

[200HZ]

Slope level: [–12], [–24]

Only frequencies higher than the high-pass

filter (HPF) cutoff are output from the

speakers.

Menu Item Description

*1 Not available when [SUB.W/SUB.W] is selected in [SP-P/O MODE] in the INITIAL settings

(page 5).

*2 Not available when [REAR/REAR] is selected in [SP-P/O MODE] in the INITIAL settings

(page 5).

*3 Not available when [OFF] is selected in [SUB.W].

You can also access to these menus when the unit is turned off.

SLA

[+4] to [–4] Adjust the volume level for each source

except RADIO.

Each of the below combinations are set to

the same setting automatically.

• USB, APP (Android)

SYSTEM settings

Menu Item Description

LANGUAGE

[ENG](English),

[РУС](Russian), [TUR](Turkish)

Select the language to display the text

information from a compressed audio file.

CLOCK SET

Set the clock (page 4).

12H/24H

[12H], [24H] Select the time notation.

AUX

[ON], [OFF] Set to [ON] when using an auxiliary device

connected to the unit.

Menu Item Description

_127075007251_artwork.book Page 8 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\020Chapter_EN.fm

MVH-09UB/MVH-09UBG

127075007251

English

USB AUTO

[ON], [OFF] Select [ON] to automatically switch to [USB]

source when a USB device/Android is

connected to the unit.

Select [OFF] when a USB device/Android is

being connected to the unit just for

charging.

Menu Item Description

WARNING

• Use speakers over 50 W (output

value) and between 4 Ω to 8 Ω

(impedance value). Do not use 1 Ω to

3 Ω speakers for this unit.

• The black cable is ground. When

installing this unit or power amp

(sold separately), make sure to

connect the ground wire first. Ensure

that the ground wire is properly

connected to metal parts of the car’s

body. The ground wire of the power

amp and the one of this unit or any

other device must be connected to

the car separately with different

screws. If the screw for the ground

wire loosens or falls out, it could

result in fire, generation of smoke or

malfunction.

Important

• When installing this unit in a vehicle

without an ACC (accessory) position

on the ignition switch, failure to

connect the red cable to the terminal

that detects operation of the ignition

key may result in battery drain.

• Use of this unit in conditions other

than the following could result in fire

or malfunction.

– Vehicles with a 12-volt battery and

negative grounding.

– When speaker output is used by 4

channels, use speakers over 50 W

(maximum input power) and

between 4 Ω to 8 Ω (impedance

value). Do not use 1 Ω to 3 Ω

speakers for this unit.

– When rear speaker output is used

by 2 Ω of subwoofer, use speakers

over 70 W (maximum input power).

* Please refer to connection for a

connection method.

• To prevent a short-circuit,

overheating or malfunction, be sure

to follow the directions below.

– Disconnect the negative terminal

of the battery before installation.

–Secure the wiring with cable

clamps or adhesive tape. Wrap

Connections/Installation

Connections

Ground wire POWER AMP

Other devices

(Another electronic

device in the car)

Metal parts of

car’s body

*1 Not supplied for this unit

ACC position No ACC position

_127075007251_artwork.book Page 9 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\020Chapter_EN.fm

MVH-09UB/MVH-09UBG

127075007251

adhesive tape around wiring that

comes into contact with metal

parts to protect the wiring.

–Place all cables away from moving

parts, such as the shift lever and

seat rails.

–Place all cables away from hot

places, such as near the heater

outlet.

– Do not connect the yellow cable to

the battery by passing it through

the hole to the engine

compartment.

–Cover any disconnected cable

connectors with insulating tape.

–Do not shorten any cables.

–Never cut the insulation of the

power cable of this unit in order to

share the power with other devices.

The current capacity of the cable is

limited.

–Use a fuse of the rating prescribed.

–Never wire the negative speaker

cable directly to ground.

–Never band together negative

cables of multiple speakers.

• When this unit is on, control signals

are sent through the blue/white

cable. Connect this cable to the

system remote control of an external

power amp or the vehicle’s auto-

antenna relay control terminal (max.

300mA 12 V DC). If the vehicle is

equipped with a glass antenna,

connect it to the antenna booster

power supply terminal.

• Never connect the blue/white cable

to the power terminal of an external

power amp. Also, never connect it to

the power terminal of the auto

antenna. Doing so may result in

battery drain or a malfunction.

• The black cable is ground. Ground

cables for this unit and other

equipment (especially, high-current

products such as power amps) must

be wired separately. If they are not,

an accidental detachment may result

in a fire or malfunction.

This unit

Rear output or subwoofer output

Antenna input

Power cord input

Fuse (10 A)

Power cord

Perform these connections when not

connecting a rear speaker lead to a

subwoofer.

Perform these connections when

using a subwoofer without the

optional amplifier.

To power cord input

Left

Right

Front speaker

Rear speaker

White

White/black

Gray

Gray/black

Green

Green/black

Violet

Violet/black

Black (chassis ground)

Connect to a clean, paint-free

metal location.

Yel low

Connect to the constant 12 V

supply terminal.

Red

Connect to terminal controlled by

the ignition switch (12 V DC).

Blue/white

Connect to the system control

terminal of the power amp or auto-

antenna relay control terminal

(max. 300 mA 12 V DC).

Subwoofer (4 Ω)

When using a subwoofer of 2 Ω, be

sure to connect the subwoofer to

the violet and violet/black leads of

this unit. Do not connect anything

to the green and green/black leads.

Not used.

Subwoofer (4 Ω) × 2

NOTE

Change the initial menu of this unit.

Refer to [SP-P/O MODE] (page 5). The

subwoofer output of this unit is

monaural.

Power amp (sold separately)

Perform these connections when

using the optional amplifier.

_127075007251_artwork.book Page 10 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\020Chapter_EN.fm

MVH-09UB/MVH-09UBG

127075007251

English

System remote control

Connect to blue/white cable.

Power amp (sold separately)

Connect with RCA cables (sold

separately)

To rear output or subwoofer output

Rear speaker or subwoofer

Important

• Check all connections and systems

before final installation.

• Do not use unauthorized parts as

this may cause malfunctions.

• Consult your dealer if installation

requires drilling of holes or other

modifications to the vehicle.

• Do not install this unit where:

–it may interfere with operation of

the vehicle.

–it may cause injury to a passenger

as a result of a sudden stop.

• Optimum

performance is

obtained when the

unit is installed at an

angle of less than 60°.

• When installing, to ensure proper

heat dispersal when using this unit,

make sure you leave ample space

behind the rear panel and wrap any

loose cables so they are not blocking

the vents.

DIN mount installation

1 Insert the supplied mounting

sleeve into the dashboard.

2 Secure the mounting sleeve by

using a screwdriver to bend the

metal tabs (90°) into place.

Dashboard

Mounting sleeve

• Make sure that the unit is

installed securely in place. An

unstable installation may cause

skipping or other malfunctions.

When not using the supplied

mounting sleeve

1 Line up the holes on the

mounting bracket with the holes

on the sides of the unit to attach

the bracket.

Installation

Leave ample

space

5 cm

2 Screw in one screw on each side to

hold the unit in place.

Tapping screw (φ5 mm × 9 mm,

not supplied with product)

Mounting bracket

Dashboard or console

Using the included bracket

Check to make sure that the included

bracket matches your particular

model of vehicle and then attach it to

the unit as shown below.

Removing the unit (installed

with the supplied mounting

sleeve)

1 Remove the trim ring.

Trim ring

Notched tab

• Releasing the front panel allows

easier access to the trim ring.

• When reattaching the trim ring,

point the side with the notched

tab down.

2 Insert the supplied extraction

keys into both sides of the unit

until they click into place.

3 Pull the unit out of the dashboard.

Screw

Bracket

_127075007251_artwork.book Page 11 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\020Chapter_EN.fm

MVH-09UB/MVH-09UBG

127075007251

The display automatically returns to

the normal display.

→ No operations have been made for

about 30 seconds.

– Perform an operation.

The repeat play range changes

unexpectedly.

→ Depending on the repeat play

range, the selected range may

change when another folder or

track is being selected or during

fast forwarding/reversing.

– Select the repeat play range

again.

A subfolder is not played back.

→ Subfolders cannot be played when

[FLD] (folder repeat) is selected.

– Select another repeat play range.

The sound is intermittent.

→ You are using a device, such as a

cellular phone, that may cause

audible interference.

– Move electrical devices that may

be causing the interference away

from the unit.

Common

AMP ERROR

→ This unit fails to operate or the

speaker connection is incorrect.

→ The protective circuit is activated.

–Check the speaker connection.

–Turn the ignition switch OFF and

back to ON again. If the message

remains, contact your dealer or an

authorized Pioneer Service

Station for assistance.

NO XXXX (NO TITLE, for example)

→ There is no embedded text

information.

–Switch the display or play another

track/file.

USB device

FORMAT READ

→ Sometimes there is a delay

between the start of playback and

when you start to hear any sound.

–Wait until the message

disappears and you hear sound.

NO AUDIO

→ There are no songs.

–Transfer the audio files to the USB

device and connect.

→ The connected USB device has

security enabled.

Additional Information

Troubleshooting Error messages

_127075007251_artwork.book Page 12 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\020Chapter_EN.fm

MVH-09UB/MVH-09UBG

127075007251

English

– Follow the USB device

instructions to disable the

security.

SKIPPED

→ The connected USB device contains

DRM protected files.

– The protected files are skipped.

PROTECT

→ All the files on the connected USB

device are embedded with DRM.

– Replace the USB device.

N/A USB

→ The connected USB device is not

supported by this unit.

– Disconnect your device and

replace it with a compatible USB

device.

CHECK USB

→ The USB connector or USB cable

has short-circuited.

– Check that the USB connector or

USB cable is not caught in

something or damaged.

→ The connected USB device

consumes more than maximum

allowable current.

– Disconnect the USB device and

do not use it. Turn the ignition

switch OFF and back to ACC or

ON. Connect only compliant USB

devices.

ERROR-19

→ Communication failed.

–Perform one of the following

operations, then return to the

USB source.

• Turn the ignition switch OFF and

back to ON.

• Disconnect the USB device.

• Change to a different source.

ERROR-23

→ USB device was not formatted

properly.

– Format the USB device with

FAT12, FAT16 or FAT32.

USB storage device

• Connections via USB hubs are not

supported.

• Firmly secure the USB storage device

before driving. Do not let the USB

storage device fall onto the floor,

where it may become jammed under

the brake or accelerator pedal.

• Depending on the USB storage

device, the following problems may

occur.

–Operations may vary.

– The storage device may not be

recognized.

– Files may not be played back

properly.

– The device may cause audible

interference when you are listening

to the radio.

Handling guidelines

• Only the first 32 characters can be

displayed as a file name (including

the file extension) or a folder name.

• The unit may not work properly

depending on the application used

to encode WMA files.

• There may be a slight delay at the

start of the playback of audio files

embedded with image data, or audio

files stored on a USB device with

numerous folder hierarchies.

• Russian text to be displayed on this

unit should be encoded in one of the

following character sets:

–Unicode (UTF-8, UTF-16)

– A character set other than Unicode

that is used in a Windows

environment and is set to Russian

in the multi-language setting

CAUTION

• Pioneer cannot guarantee

compatibility with all USB mass

storage devices, and assumes no

responsibility for any loss of data on

media players, smartphones, or

other devices while using this

product.

• Do not leave a USB storage device in

any place that is subject to high

temperatures.

WMA files

MP3 files

WAV files

FLAC files

• FLAC files may not be playable,

depending on the encoder.

Compressed audio

compatibility

File extension .wma

Bit rate 48 kbps to 320 kbps

(CBR), 48 kbps to

384 kbps (VBR)

Sampling

frequency

32 kHz, 44.1 kHz, 48

kHz

Windows Media™

Audio Professional,

Lossless, Voice/

DRM Stream/

Stream with video

Not compatible

File extension .mp3

Bit rate 8 kbps to 320 kbps

(CBR), VBR

Sampling

frequency

16 kHz to 48 kHz (32

kHz, 44.1 kHz, 48

kHz for emphasis)

Compatible ID3 tag

version

2.2, 2.3, 2.4

M3u playlist Not compatible

MP3i (MP3

interactive), mp3

PRO

Not compatible

File extension .wav

Quantization bits 8 and 16 (LPCM), 4

(MSADPCM)

Sampling

frequency

16 kHz to 48 kHz

(LPCM), 22.05 kHz

and 44.1 kHz (MS

ADPCM)

_127075007251_artwork.book Page 13 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\020Chapter_EN.fm

MVH-09UB/MVH-09UBG

127075007251

USB device

• There may be a slight delay when

starting playback of audio files on a

USB storage device with numerous

folder hierarchies.

The user cannot assign folder

numbers and specify playback

sequences with this unit. Sequence of

audio file depends on the connected

device.

Note that the hidden files in a USB

device cannot be played back.

Example of a hierarchy

File extension .flac

Sampling

frequency

8/11.025/12/16/

22.05/24/32/44.1/

48 kHz

Quantization bit

rate

16 bit

Channel mode 1/2 ch

Playable folder

hierarchy

Up to eight tiers (A

practical hierarchy

is less than two

tiers.)

Playable folders Up to 500

Playable files Up to 15 000

Playback of

protected files

Not compatible

Partitioned USB

device

Only the first

partition can be

played.

Sequence of audio files

Folder

Compressed

audio file

to : Playback sequence

01 to 05: Folder number

WMA

Windows Media is either a registered

trademark or trademark of Microsoft

Corporation in the United States and/

or other countries.

This product includes technology

owned by Microsoft Corporation and

cannot be used or distributed without

a license from Microsoft Licensing, Inc.

FLAC

Foundation

Redistribution and use in source and

binary forms, with or without

modification, are permitted provided

that the following conditions are met:

–Redistributions of source code must

retain the above copyright notice,

this list of conditions and the

following disclaimer.

–Redistributions in binary form must

reproduce the above copyright

notice, this list of conditions and the

following disclaimer in the

documentation and/or other

materials provided with the

distribution.

–Neither the name of the Xiph.org

Foundation nor the names of its

contributors may be used to endorse

or promote products derived from

this software without specific prior

written permission.

THIS SOFTWARE IS PROVIDED BY THE

CONTRIBUTORS “AS IS” AND ANY

EXPRESS OR IMPLIED WARRANTIES,

INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE

Russian character

chart

trademark

D: Display C: Character

_127075007251_artwork.book Page 14 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\020Chapter_EN.fm

MVH-09UB/MVH-09UBG

127075007251

English

FOUNDATION OR CONTRIBUTORS BE

LIABLE FOR ANY DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, EXEMPLARY, OR

CONSEQUENTIAL DAMAGES

(INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE

GOODS OR SERVICES; LOSS OF USE,

DATA, OR PROFITS; OR BUSINESS

INTERRUPTION) HOWEVER CAUSED

AND ON ANY THEORY OF LIABILITY,

WHETHER IN CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING

IN ANY WAY OUT OF THE USE OF THIS

SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE.

Android™

Android is a trademark of Google Inc.

General

Power source: 14.4 V DC (10.8 V to 15.1

V allowable)

Grounding system: Negative type

Maximum current consumption: 10.0

Dimensions (W × H × D):

DIN

Chassis: 178 mm × 50 mm × 97

Nose: 188 mm × 58 mm × 17 mm

Chassis: 178 mm × 50 mm × 97

Nose: 170 mm × 46 mm × 17 mm

Weight: 0.5 kg

Audio

Maximum power output:

•50 W × 4 ch/4 Ω (for no

subwoofer)

• 50 W × 2 ch/4 Ω + 70 W × 1 ch/2

Ω (for subwoofer)

Continuous power output:

22 W × 4 (50 Hz to 15 000 Hz, 5 %

THD, 4 Ω load, both channels

driven)

Load impedance: 4 Ω (4 Ω to 8 Ω

allowable)

Preout maximum output level: 2.0 V

Loudness contour: +10 dB (100 Hz),

+6.5 dB (10 kHz) (volume: –30 dB)

Equalizer (5-Band Graphic Equalizer):

Frequency: 80 Hz/250 Hz/800 Hz/

2.5 kHz/8 kHz

Equalization range: ±12 dB (2 dB

step)

Subwoofer (mono):

Frequency: 50 Hz/63 Hz/80 Hz/

100 Hz/125 Hz/160 Hz/200 Hz

Slope: –12 dB/oct, –24 dB/oct

Gain: +6 dB to –24 dB

Phase: Normal/Reverse

USB

USB standard specification: USB 2.0

full speed

Maximum current supply: 500 mA

USB Protocol:

MSC (Mass Storage Class)

AOA (Android Open Accessory)

2.0

File system: FAT12, FAT16, FAT32

MP3 decoding format: MPEG-1 & 2

Audio Layer 3

Specifications

WMA decoding format: Ver. 7, 7.1, 8, 9

(2 ch audio) (Windows Media

Player)

FLAC decoding format:

v1.2.1 (Free Lossless Audio

Codec)

WAV signal format: Linear PCM & MS

ADPCM (Non-compressed)

FM tuner

Frequency range (F1): 65.0 MHz to

74.0 MHz

Usable sensitivity (F1): 11 dBf (1.0 μV/

75 Ω, mono, S/N: 30 dB)

Signal-to-noise ratio (F1): 72 dB (IEC-A

network)

Frequency range (FM2/FM3): 87.5 MHz

to 108.0 MHz

Usable sensitivity (FM2/FM3): 11 dBf

(1.0 μV/75 Ω, mono, S/N: 30 dB)

Signal-to-noise ratio (FM2/FM3): 72 dB

(IEC-A network)

MW tuner

Frequency range: 531 kHz to 1 602 kHz

Usable sensitivity: 25 μV (S/N: 20 dB)

Signal-to-noise ratio: 62 dB (IEC-A

network)

LW tuner

Frequency range: 153 kHz to 281 kHz

Usable sensitivity: 28 μV (S/N: 20 dB)

Signal-to-noise ratio: 62 dB (IEC-A

network)

NOTE

Specifications and the design are

subject to modifications without

notice.

_127075007251_artwork.book Page 15 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\020Chapter_EN.fm

MVH-09UB/MVH-09UBG

127075007251

_127075007251_artwork.book Page 16 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\020Chapter_EN.fm

MVH-09UB/MVH-09UBG

127075007251

English

_127075007251_artwork.book Page 17 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\030Chapter_RU.fm

MVH-09UB/MVH-09UBG

127075007251

Перед началом эксплуатации .............................................. 2

Начало работы.......................................................................... 3

Радио ........................................................................................... 5

USB/AUX ...................................................................................... 6

Настройки .................................................................................. 8

Настройки FUNCTION ............................................................ 8

Настройки AUDIO.................................................................... 8

Настройки SYSTEM ................................................................. 9

Подключения/Установка ..................................................... 10

Дополнительная информация........................................... 14

О данном руководстве:

• В следующих инструкциях USB-накопитель и аудиопроигрыватель USB

называются “USB-устройство”.

Содержание

Благодарим Вас за покупку этого изделия компании PIONEER

Для обеспечения правильности эксплуатации внимательно прочитайте данное

руководство перед началом использования изделия. Особенно важно, чтобы Вы

прочли и соблюдали инструкции, помеченные в данном руководстве заголовками

ПРЕДУПРЕЖДЕНИЕ и ВНИМАНИЕ. Держите данное руководство под рукой для

обращения к нему в будущем.

Частные лица в странах Евросоюза, Швейцарии и Норвегии могут бесплатно

возвращать использованные электронные изделия в специализированные пункты

приема или в магазин (при покупке аналогичного нового устройства).

Если Ваша страна не указана в приведенном выше перечне, обращайтесь в органы

местного управления за инструкциями по правильной утилизации продукта.

Тем самым Вы обеспечите утилизацию Вашего изделия с соблюдением обязательных

процедур по обработке, утилизации и вторичной переработке и, таким образом,

предотвратите потенциальное негативное воздействие на окружающую среду и

здоровье людей.

Дату изготовления оборудования можно определить по серийному номеру, который

содержит информацию о месяце и годе производства.

Перед началом эксплуатации

Если вы желаете утилизировать данное изделие, не выбрасывайте его вместе с

обычным бытовым мусором. Существует отдельная система сбора использованных

электронных изделий в соответствии с законодательством, которая предполагает

соответствующее обращение, возврат и переработку.

_127075007251_artwork.book Page 2 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\030Chapter_RU.fm

MVH-09UB/MVH-09UBG

127075007251

Русский

ПРЕДУПРЕЖДЕНИЕ

• Не пытайтесь самостоятельно производить установку или ремонт изделия.

Установка или ремонт изделия лицами, не обладающими специальными

навыками и опытом работы с электронным оборудованием и

автомобильными аксессуарами, могут создать опасность поражения

электрическим током или иных инцидентов.

• Ни в коем случае не пытайтесь управлять устройством во время движения. Прежде

чем использовать органы управления устройством, необходимо съехать с дороги и

припарковать автомобиль в безопасном месте.

ВНИМАНИЕ

• Не допускайте попадания жидкости на устройство. Это может повлечь поражение

электрическим током. Кроме того, попадание жидкости в устройство может стать

причиной его выхода из строя, перегрева и появления дыма.

• Всегда сохраняйте уровень громкости достаточно низким, чтобы были слышны звуки

извне.

При возникновении проблем

При неполадках в работе этого изделия свяжитесь с торговым представителем

компании-производителя или с ближайшим сервисным пунктом PIONEER.

MVH-09UB/09UBG

Часто используемые операции

Начало работы

Основные операции

Назначение Операция

Включение питания* Нажмите SRC/OFF для включения

питания.

Нажмите и удерживайте SRC/OFF

для выключения питания.

Настройка громкости Поверните регулятор M.C..

Выбор источника Несколько раз нажмите SRC/OFF.

Изменение информации на дисплее Несколько раз нажмите DISP.

Возврат к предыдущему экрану/

списку

Нажмите BAND/DIMMER .

Возврат к обычному дисплею из

меню

Нажмите и удерживайте BAND/

DIMMER .

SRC (источник)/OFF

Кнопка отсоединения

Окно дисплея

Регулятор M.C. (многозадачное управление)

BAND/DIMMER

DISP (дисплей)

_127075007251_artwork.book Page 3 Thursday, November 24, 2016 10:34 AM

H:\PDF-OUT\127075007251\030Chapter_RU.fm

MVH-09UB/MVH-09UBG

127075007251

* Когда голубой/белый провод этого устройства подключен к терминалу релейного

управления автоматической антенны, антенна на автомобиле выдвигается при

включении источника сигнала этого устройства. Чтобы втянуть антенну, выключите

источник сигнала.

Индикация на дисплее

Снимите переднюю панель во избежание кражи. Перед снятием панели

отсоедините кабели и устройства, подключенные к передней панели, и

отключите устройство.

Важно

• Оберегайте переднюю панель от сильных ударов.

• Не подвергайте переднюю панель воздействию прямых солнечных лучей и высоких

температур.

Индикаци

Описание

Отображается при наличии нижнего уровня меню или папки.

Отображается при нажатии кнопки .

Отображается при настройке функции поиска локальных

радиостанций (стр. 8).

Отображается при настройке произвольного/перемешанного

воспроизведения.

Отображается при установке повтора воспроизведения.

Снятие передней панели

Снятие Установка

• Всегда храните снятую панель в защитном чехле или сумке.

После установки устройства поверните ключ зажигания в положение ON;

на дисплее отобразится [SET UP :YES].

1 Нажмите регулятор M.C..

Если в течение 30 секунд устройство не используется, установочное

меню не будет выводиться. Если вы хотите выполнить настройку

позже, поверните M.C., чтобы выбрать [NO], и нажмите для

подтверждения.

2 Поверните M.C. для выбора параметров, затем нажмите для

подтверждения.

Для перехода к следующему пункту меню необходимо подтвердить

выбор.

3 [QUIT :YES] отображается после выполнения всех настроек.

Для возврата к первому элементу установочного меню поверните

M.C. для выбора [QUIT :NO], затем нажмите для подтверждения.

4 Нажмите M.C. для подтверждения настроек.

ПРИМЕЧАНИЯ

• Вы можете отменить настройку параметра меню, нажав кнопку SRC/OFF.

• Настроить параметры меню можно в настройках SYSTEM (стр. 9) и настройках INITIAL

(стр. 5).

Установочное меню

Элемент меню Описание

LANGUAGE Выбор языка для отображения текстовой

информации с сжатого аудиофайла.

[ENG](Английский),

[РУС](Русский),

[TUR](Турецкий)

CLOCK SET Настройка часов.

FM STEP Выбор шага настройки в FM-диапазоне (100 кГц

или 50 кГц).

[100], [50]

_127075007251_artwork.book Page 4 Thursday, November 24, 2016 10:34 AM

Страница загружается ...

Pioneer MVH-09UBG Руководство пользователя

Бренд: Pioneer

Модель: MVH-09UBG

Категория: Мультимедиа-приемники для автомобилей

Тип: Руководство пользователя

Скачать PDF

сообщить о нарушении

на других языках

English: Pioneer MVH-09UBG User manual

Pioneer MVH-09UBG Руководство пользователя

Pioneer MVH-09UBG Руководство пользователя

на других языках

Похожие модели бренда