Pioneer MVH-171UB Руководство пользователя

Бренд: Pioneer

Модель: MVH-171UB

Тип: Руководство пользователя

English Русский

DIGITAL MEDIA RECEIVER

ЦИФРОВОЙ МУЛЬТИМЕДИЙНЫЙ ПРИЕМНИК

MVH-171UB

Owner’s Manual

Руководство пользователя

2En

Before You Start....................................................................................... 3

Getting Started........................................................................................ 3

Radio.......................................................................................................... 6

USB/AUX ................................................................................................... 7

Settings ..................................................................................................... 8

FUNCTION settings ................................................................................. 8

AUDIO settings......................................................................................... 8

SYSTEM settings ...................................................................................... 9

ILLUMINATION settings.......................................................................... 9

Connections/Installation ..................................................................... 10

Additional Information ........................................................................ 12

Table of Contents

About this manual:

In the following instructions, a USB memory or USB audio player are referred to as “USB

device”.

3En

English

Thank you for purchasing this PIONEER product

To ensure proper use, please read through this manual before using this product. It is especially

important that you read and observe WARNINGs and CAUTIONs in this manual. Please keep the

manual in a safe and accessible place for future reference.

WARNING

•Do not attempt to install or service this product by yourself. Installation or servicing of this

product by persons without training and experience in electronic equipment and automotive

accessories may be dangerous and could expose you to the risk of electric shock, injury or other

hazards.

• Do not attempt to operate the unit while driving. Make sure to pull off the road and park your vehicle

in a safe location before attempting to use the controls on the device.

CAUTION

• Do not allow this unit to come into contact with moisture and/or liquids. Electrical shock could result.

Also, damage to this unit, smoke, and overheating could result from contact with liquids.

• Always keep the volume low enough to hear outside sounds.

If you experience problems

Should this unit fail to work properly, please contact your dealer or nearest authorized PIONEER Service

Station.

MVH-171UB

* This button is referred to as DISP in this manual.

Remote Control

Before You Start Getting Started

Basic operation

SRC (source)/OFF

Detach button

Display window

M.C. (multi-control) dial

BAND /DIMMER

Display button*

SRC (source)

VOLUME +/–

MUTE

DISP (display)

FUNCTION AUDIO

4En

Frequently used operations

* When this unit’s blue/white lead is connected to the vehicle’s auto-antenna relay control terminal,

the vehicle’s antenna extends when this unit’s source is turned on. To retract the antenna, turn the

source off.

Display indication

Detach the front panel to prevent theft. Remove any cables and devices attached to the

front panel and turn off the unit before detaching it.

Important

• Avoid subjecting the front panel to excessive shock.

• Keep the front panel out of direct sunlight and high temperatures.

• Always store the detached front panel in a protective case or bag.

Remove the insulation sheet before use.

WARNING

• Keep the battery out of the reach of children. Should the battery be swallowed, consult a doctor

immediately.

• Do not expose the battery or remote control to excessive heat such as direct sunlight or fire.

CAUTION

• There is a potential danger of explosion if the battery is incorrectly replaced. When replacing the

battery, replace it with the same type.

• Do not handle or store the battery with metallic tools or objects.

Operation

Purpose Head Unit Remote Control

Turn on the power* Press SRC/OFF to turn on

the power.

Press and hold SRC/OFF to

turn off the power.

Press SRC to turn on the

power.

Press and hold SRC to turn

off the power.

Adjust the volume Turn the M.C. dial. Press VOLUME + or –.

Press MUTE to mute the

unit. Press again to unmute.

Select a source Press SRC/OFF repeatedly. Press SRC repeatedly.

Change the display

information

Press DISP repeatedly. Press DISP repeatedly.

Return to the previous

display/list

Press /DIMMER.Press / to select the

next/previous folder.

Return to the normal display

from the menu

Press BAND

–

Indication Description

Appears when a lower tier of the menu or folder exists.

Appears when the button is pressed.

Appears when the local seek tuning function is set (page 8).

Appears when a traffic program is received.

Appears when traffic announcements are received (page 8).

Appears when the sound retriever function is set (page 8).

Appears when random/shuffle play is set.

Appears when repeat play is set.

Detaching the front panel

Preparing the remote control

Detach Attach

How to replace the battery

Insert the CR2025 (3 V) battery with the plus (+) and

minus (–) poles orientated properly.

5En

English

• If the battery leaks, remove the battery and wipe the remote control completely clean. Then install a

new battery.

• When disposing of used batteries, compliance with governmental regulations or environmental

institutions’ rules that apply in your country/area must be followed that pertain to any special

handling needed for disposal.

Important

• Do not store the remote control in high temperatures or direct sunlight.

• Do not let the remote control fall onto the floor, where it may become jammed under the brake or

accelerator pedal.

When you turn the ignition switch to ON after installation, [SET UP :YES] appears in the

display.

1 Press the M.C. dial.

The setup menu disappears after 30 seconds of no operation. If you prefer not to set

at this time, turn the M.C. dial to select [NO], then press to confirm.

2 Turn the M.C. dial to select the options, then press to confirm.

To proceed to the next menu option, you need to confirm your selection.

3 [QUIT :YES] appears when all the settings have been made.

To return to the first item of the setup menu, turn the M.C. dial to select [QUIT :NO],

then press to confirm.

4 Press the M.C. dial to confirm the settings.

NOTES

• You can cancel the menu setting by pressing SRC/OFF.

• These settings can be made at any time from the SYSTEM settings (page 9) and INITIAL settings

(page 5).

1 Press the M.C. dial to display the main menu.

2 Turn the M.C. dial to select [SYSTEM], then press to confirm.

3 Turn the M.C. dial to select [DEMO OFF], then press to confirm.

4 Turn the M.C. dial to select [YES], then press to confirm.

1 Press and hold SRC/OFF until the unit turns off.

2 Press and hold SRC/OFF to display the main menu.

3 Turn the M.C. dial to select [INITIAL], then press to confirm.

4 Turn the M.C. dial to select an option, then press to confirm.

Setup menu

Menu Item Description

LANGUAGE Select the language to display the text information from a

compressed audio file.

[ENG](English),

[РУС](Russian),

[TUR](Turkish)

CLOCK SET Set the clock.

FM STEP Select the FM tuning step from 100 kHz or 50 kHz.

[100], [50]

Canceling the demonstration display (DEMO OFF)

INITIAL settings

Menu Item Description

FM STEP Select the FM tuning step from 100 kHz or 50 kHz.

[100], [50]

SP-P/O MODE Select when there is a full-range speaker connected to the rear

speaker output leads and there is a subwoofer connected to the

RCA output.

[REAR/SUB.W]

[SUB.W/SUB.W] Select when there is a passive subwoofer connected directly to

the rear speaker output leads and there is a subwoofer

connected to the RCA output.

[REAR/REAR] Select when there are full-range speakers connected to the rear

speaker output leads and RCA output. If there is a full-range

speaker connected to the rear speaker output leads, and the

RCA output is not used, you may select either [REAR/SUB.W] or

[REAR/REAR].

SYSTEM RESET Select [YES] to initialize the unit settings. The unit will be

restarted automatically. (Some of the settings may be retained

even after resetting the unit.)

[YES], [CANCEL]

6En

The tuner frequencies on this unit are allocated for use in Western Europe, Asia, the

Middle East, Africa and Oceania. Use in other areas may result in poor reception. The RDS

(radio data system) function only works in areas that broadcast RDS signals for FM

stations.

1 Press SRC/OFF to select [RADIO].

2 Press BAND to select the band from [FM1], [FM2], [FM3], [MW] or [LW].

3 Press a number button (1/ to 6/).

TIP

The / buttons can be also used to select a preset station when [SEEK] is set to [PCH] in the

FUNCTION settings (page 8).

The six strongest stations are stored on the number buttons (1/ to 6/).

1 After selecting the band, press the M.C. dial to display the main menu.

2 Turn the M.C. dial to select [FUNCTION], then press to confirm.

3 Turn the M.C. dial to select [BSM], then press to confirm.

To seek a station manually

After selecting the band, press / to select a station.

Press and hold / then release to seek an available station. Scanning stops

when the unit receives a station. To cancel seek tuning, press / .

NOTE

[SEEK] needs to be set to [MAN] in the FUNCTION settings (page 8).

To store stations manually

While receiving the station you want to store, press and hold one of the number

buttons (1/ to 6/ ) until it stops flashing.

The unit searches for a station by PTY (program type) information.

1 Press during FM reception.

2 Turn the M.C. dial to select a program type from [NEWS/INFO], [POPULAR],

[CLASSICS] or [OTHERS].

3 Press the M.C. dial.

The unit begins to search for a station. When it is found, its program service name is

displayed.

NOTES

• To cancel the search, press the M.C. dial.

• The program of some stations may differ from that indicated by the transmitted PTY.

• If no station is broadcasting the type of program you searched for, [NOT FOUND] is displayed for

about two seconds and then the tuner returns to the original station.

PTY list

For more details about PTY list, visit the following site:

http://www.pioneer.eu/eur/products/25/121/tech/CarAudio/PTY.html

Radio

Receiving preset stations

Best stations memory (BSM)

Using PTY functions

7En

English

Disconnect headphones from the device before connecting it to the unit.

USB device

Open the USB port cover.

2 Plug in the USB device using an appropriate cable.

CAUTION

Use an optional Pioneer USB cable (CD-U50E) to connect the USB storage device as any device

connected directly to the unit will protrude out from the unit, which could be dangerous.

Before removing the device, stop playback.

MTP connection

A device installed with Android OS 4.0 or later can be connected to the unit via MTP, using the cable

supplied with the device. However, depending on the connected device and the numbers of the files in

the device, audio files/songs may not be able to be played back via MTP. Note that MTP connection is

not compatible with WAV and FLAC file formats.

AUX

Insert the stereo mini plug into the AUX input jack.

2 Press SRC/OFF to select [AUX] as the source.

NOTE

If [AUX] is set to [OFF] in the SYSTEM settings, [AUX] cannot be selected as a source.

You can make various adjustments in the FUNCTION settings (page 8).

Note that the following operations do not work for an AUX device. To operate an AUX

device, use the device itself.

*1 Compressed audio files only

*2 When there is no 3/S.Rtrv button on the unit, the sound retriever function can be set by the

FUNCTION settings.

USB/AUX

Playing back

AUX input jack (3.5 mm stereo jack)

USB port

SRC (source)/OFF

M.C. (multi-control) dial

Operations

Purpose Operation

Select a folder/album*1 Press 1/ or 2/.

Select a track/song (chapter) Press or .

Fast forward or reverse Press and hold or .

Search for a file from a list 1 Press to display the list.

2 Turn the M.C. dial to select the desired

file (folder) name or category, then press

to confirm.

3 Turn the M.C. dial to select the desired

file, then press to confirm.

Playback starts.

View a list of the files in the selected folder/

category*1

Press the M.C. dial when a folder/category

is selected.

Play a song in the selected folder/

category*1

Press and hold the M.C. dial when a folder/

category is selected.

Repeat play Press 6/.

Random play Press 5/.

Pause/resume playback Press 4/PAUSE.

Sound retriever*2 Press 3/S.Rtrv.

[1]: Effective for low compression rates

[2]: Effective for high compression rates

Return to root folder (USB only)*1 Press and hold BAND.

Change drives in USB device

(Devices that support the USB mass storage

device class protocol only)

Press BAND.

8En

You can adjust various settings in the main menu.

1 Press the M.C. dial to display the main menu.

2 Turn the M.C. dial to select one of the categories below, then press to confirm.

• FUNCTION settings (page 8)

• AUDIO settings (page 8)

• SYSTEM settings (page 9)

• ILLUMINATION settings (page 9)

3 Turn the M.C. dial to select the options, then press to confirm.

The menu items vary according to the source.

Settings

FUNCTION settings

Menu Item Description

FM SETTING

[TALK], [STANDARD], [MUSIC] Match the sound quality level with the broadcast

signal conditions of the FM band signal.

(Available only when FM band is selected.)

BSM

Store the six strongest stations on the number

buttons (1/ to 6/ ) automatically.

REGIONAL

[ON], [OFF] Limit the reception to the specific regional

programs when AF (alternative frequencies

search) is selected. (Available only when FM

band is selected.)

LOCAL

FM: [OFF], [LV1], [LV2], [LV3], [LV4]

MW/LW: [OFF], [LV1], [LV2]

Restrict the tuning station according to the

signal strength.

[ON], [OFF] Receive current traffic information if available.

(Available only when FM band is selected.)

[ON], [OFF] Allow the unit to retune to a different frequency

providing the same station. (Available only when

FM band is selected.)

NEWS

[ON], [OFF] Interrupt the currently selected source with

news programs. (Available only when FM band is

selected.)

SEEK

[MAN], [PCH] Assign / buttons to seek the stations

one by one (manual tuning) or select a station

from the preset channels.

S.RTRV

[1] (effective for low compression

rates),

[2] (effective for high

compression rates),

[OFF]

Enhance compressed audio and restore rich

sound. (Not available when the FLAC file is

played back.)

AUDIO settings

Menu Item Description

FADER*1

Adjust the front and rear speaker balance.

BALANCE

Adjust the left and right speaker balance.

EQ SETTING

[SUPER BASS], [POWERFUL],

[NATURAL], [VOCAL], [CUSTOM1],

[CUSTOM2], [FLAT]

Select an equalizer band and

level for further customizing.

Equalizer band: [80HZ], [250HZ],

[800HZ], [2.5KHZ], [8KHZ]

Equalizer level: [+6] to [–6]

Select or customize the equalizer curve.

[CUSTOM1] can be set separately for each source.

[CUSTOM2] is a shared setting used for all

sources.

You can also switch the equalizer by pressing

repeatedly.

Menu Item Description

USB

9En

English

*1 Not available when [SUB.W/SUB.W] is selected in [SP-P/O MODE] in the INITIAL settings (page 5).

*2 Not available when [REAR/REAR] is selected in [SP-P/O MODE] in the INITIAL settings (page 5).

*3 Not available when [OFF] is selected in [SUB.W].

You can also access to these menus when the unit is turned off.

* [PW SAVE] is canceled if the vehicle battery is disconnected and will need to be turned back on once

the battery is reconnected. When [PW SAVE] is off, depending on connection methods, the unit may

continue to draw power from the battery if your vehicle’s ignition does not have an ACC (accessory)

position.

LOUDNESS

[OFF], [LOW], [MID], [HI] Compensate for clear sound at low volume.

SUB.W*2

[NOR], [REV], [OFF] Select the subwoofer phase.

SUB.W CTRL*2*3

Cut-off frequency: [50HZ],

[63HZ], [80HZ], [100HZ], [125HZ],

[160HZ], [200HZ]

Output level: [–24] to [+6]

Slope level: [–12], [–24]

Only frequencies lower than those in the

selected range are output from the subwoofer.

BASS BOOST

[0] to [+6] Select the bass boost level.

HPF SETTING

Cut-off frequency: [OFF], [50HZ],

[63HZ], [80HZ], [100HZ], [125HZ],

[160HZ], [200HZ]

Slope level: [–12], [–24]

Only frequencies higher than the high-pass filter

(HPF) cutoff are output from the speakers.

SLA

[+4] to [–4] Adjust the volume level for each source except

FM.

SYSTEM settings

Menu Item Description

LANGUAGE

[ENG](English), [РУС](Russian),

[TUR](Turkish)

Select the language to display the text

information from a compressed audio file.

CLOCK SET

Set the clock (page 5).

12H/24H

[12H], [24H] Select the time notation.

Menu Item Description

AUTO PI

[ON], [OFF] Search for a different station with the same

programming, even if using a preset station.

AUX

[ON], [OFF] Set to [ON] when using an auxiliary device

connected to the unit.

PW SAVE*

[ON], [OFF] Reduce the battery power consumption.

Turning on the source is the only operation

allowed when this function is on.

ILLUMINATION settings

Menu Item Description

DIM SETTING

[SYNC CLOCK], [MANUAL] Change the display brightness.

BRIGHTNESS

[1] to [10] Change the display brightness.

The available setting ranges differ depending on

[DIM SETTING].

Menu Item Description

10En

Important

• When installing this unit in a vehicle

without an ACC (accessory) position on

the ignition switch, failure to connect the

red cable to the terminal that detects

operation of the ignition key may result

in battery drain.

• To prevent a short-circuit, overheating or

malfunction, be sure to follow the

directions below.

–Disconnect the negative terminal of the

battery before installation.

–Secure the wiring with cable clamps or

adhesive tape. Wrap adhesive tape

around wiring that comes into contact

with metal parts to protect the wiring.

– Place all cables away from moving parts,

such as the shift lever and seat rails.

–Place all cables away from hot places,

such as near the heater outlet.

–Do not connect the yellow cable to the

battery by passing it through the hole

to the engine compartment.

–Cover any disconnected cable

connectors with insulating tape.

–Do not shorten any cables.

–Never cut the insulation of the power

cable of this unit in order to share the

power with other devices. The current

capacity of the cable is limited.

–Use a fuse of the rating prescribed.

–Never wire the negative speaker cable

directly to ground.

–Never band together negative cables of

multiple speakers.

• When this unit is on, control signals are

sent through the blue/white cable.

Connect this cable to the system remote

control of an external power amp or the

vehicle’s auto-antenna relay control

terminal (max. 300mA 12 V DC). If the

vehicle is equipped with a glass antenna,

connect it to the antenna booster power

supply terminal.

• Never connect the blue/white cable to

the power terminal of an external power

amp. Also, never connect it to the power

terminal of the auto antenna. Doing so

may result in battery drain or a

malfunction.

This unit

Power cord input

Rear output or subwoofer output

Antenna input

Fuse (10 A)

Connections/Installation

Connections

ACC position No ACC position

Power cord

Perform these connections when not

connecting a rear speaker lead to a

subwoofer.

To power cord input

Depending on the kind of vehicle, the

function of and may be different.

In this case, be sure to connect to

and to .

Yel low

Back-up (or accessory)

Yel low

Connect to the constant 12 V supply

terminal.

Red

Accessory (or back-up)

Red

Connect to terminal controlled by the

ignition switch (12 V DC).

Connect leads of the same color to each

other.

Black (chassis ground)

Blue/white

The pin position of the ISO connector

will differ depending on the type of

vehicle. Connect and when Pin 5

is an antenna control type. In another

type of vehicle, never connect and

Blue/white

Connect to the system control terminal

of the power amp (max. 300 mA 12 V

DC).

Blue/white

Connect to the auto-antenna relay

control terminal (max. 300 mA 12 V DC).

Speaker leads

White: Front left

White/black: Front left

Gray: Front right

Gray/black: Front right

Green: Rear left or subwoofer

Green/black: Rear left or subwoofer

Violet: Rear right or subwoofer

Violet/black: Rear right or subwoofer

ISO connector

In some vehicles, the ISO connector

may be divided into two. In this case, be

sure to connect to both connectors.

NOTES

• Change the initial menu of this unit. Refer to

[SP-P/O MODE] (page 5). The subwoofer

output of this unit is monaural.

• When using a subwoofer of 70 W (2 Ω), be sure

to connect the subwoofer to the violet and

violet/black leads of this unit. Do not connect

anything to the green and green/black leads.

Power amp (sold separately)

Perform these connections when using the

optional amplifier.

System remote control

Connect to blue/white cable.

Power amp (sold separately)

11En

English

Connect with RCA cables (sold

separately)

To rear output or subwoofer output

Rear speaker or subwoofer

Important

• Check all connections and systems before

final installation.

• Do not use unauthorized parts as this

may cause malfunctions.

• Consult your dealer if installation requires

drilling of holes or other modifications to

the vehicle.

• Do not install this unit where:

–it may interfere with operation of the

vehicle.

–it may cause injury to a passenger as a

result of a sudden stop.

• The semiconductor laser will be damaged

if it overheats. Install this unit away from

hot places such as near the heater outlet.

• Optimum performance is

obtained when the unit is

installed at an angle of less

than 60°.

• When installing, to ensure proper heat

dispersal when using this unit, make sure

you leave ample space behind the rear

panel and wrap any loose cables so they

are not blocking the vents.

DIN front/rear mount

This unit can be properly installed using

either front-mount or rear-mount

installation.

Use commercially available parts when

installing.

DIN Front-mount

1 Insert the mounting sleeve into the

dashboard.

For installation in shallow spaces, use

the supplied mounting sleeve. If there is

enough space, use the mounting sleeve

that came with the vehicle.

2 Secure the mounting sleeve by using a

screwdriver to bend the metal tabs

(90°) into place.

Dashboard

Mounting sleeve

Make sure that the unit is installed

securely in place. An unstable

installation may cause skipping or other

malfunctions.

DIN Rear-mount

1 Line up the holes on the mounting

bracket with the holes on the sides of

the unit to attach the bracket.

2 Screw in one screw on each side to

hold the unit in place.

Tapping screw (5 mm × 8 mm)

Mounting bracket

Installation

Leave ample

space

5 cm

Dashboard or console

Using the included bracket

You can also use the included bracket to

mount the unit. Check to make sure that

the included bracket matches your

particular model of vehicle and then attach

it to the unit as shown below.

Screw

Bracket

Removing the unit

1 Remove the trim ring.

Trim ring

Notched tab

• Releasing the front panel allows easier

access to the trim ring.

• When reattaching the trim ring, point

the side with the notched tab down.

2 Insert the supplied extraction keys

into both sides of the unit until they

click into place.

3 Pull the unit out of the dashboard.

12En

The display automatically returns to the

normal display.

→ No operations have been made for

about 30 seconds.

– Perform an operation.

The repeat play range changes

unexpectedly.

→ Depending on the repeat play range,

the selected range may change when

another folder or track is being selected

or during fast forwarding/reversing.

– Select the repeat play range again.

A subfolder is not played back.

→ Subfolders cannot be played when

[FLD] (folder repeat) is selected.

– Select another repeat play range.

The sound is intermittent.

→ You are using a device, such as a cellular

phone, that may cause audible

interference.

– Move electrical devices that may be

causing the interference away from

the unit.

Common

AMP ERROR

→ This unit fails to operate or the speaker

connection is incorrect.

→ The protective circuit is activated.

– Check the speaker connection.

– Turn the ignition switch OFF and back

to ON again. If the message remains,

contact your dealer or an authorized

Pioneer Service Station for assistance.

NO XXXX (NO TITLE, for example)

→ There is no embedded text information.

– Switch the display or play another

track/file.

USB device

FORMAT READ

→ Sometimes there is a delay between the

start of playback and when you start to

hear any sound.

– Wait until the message disappears and

you hear sound.

NO AUDIO

→ There are no songs.

– Transfer the audio files to the USB

device and connect.

→ The connected USB device has security

enabled.

– Follow the USB device instructions to

disable the security.

SKIPPED

→ The connected USB device contains

DRM protected files.

– The protected files are skipped.

PROTECT

→ All the files on the connected USB

device are embedded with DRM.

– Replace the USB device.

N/A USB

→ The connected USB device is not

supported by this unit.

– Disconnect your device and replace it

with a compatible USB device.

CHECK USB

→ The USB connector or USB cable has

short-circuited.

Additional Information

Troubleshooting

Error messages

– Check that the USB connector or USB

cable is not caught in something or

damaged.

→ The connected USB device consumes

more than maximum allowable current.

– Disconnect the USB device and do not

use it. Turn the ignition switch OFF

and back to ACC or ON. Connect only

compliant USB devices.

ERROR-19

→ Communication failed.

– Perform one of the following

operations, then return to the USB

source.

• Turn the ignition switch OFF and

back to ON.

• Disconnect the USB device.

• Change to a different source.

ERROR-23

→ USB device was not formatted properly.

– Format the USB device with FAT12,

FAT16 or FAT32.

STOP

→ There are no songs in the current list.

– Select a list that contains songs.

USB storage device

• Connections via USB hubs are not

supported.

• Firmly secure the USB storage device

before driving. Do not let the USB storage

device fall onto the floor, where it may

become jammed under the brake or

accelerator pedal.

• Depending on the USB storage device,

the following problems may occur.

–Operations may vary.

–The storage device may not be

recognized.

–Files may not be played back properly.

–The device may cause audible

interference when you are listening to

the radio.

• Only the first 32 characters can be

displayed as a file name (including the file

extension) or a folder name.

• The unit may not work properly

depending on the application used to

encode WMA files.

• There may be a slight delay at the start of

the playback of audio files embedded

with image data, or audio files stored on a

USB device with numerous folder

hierarchies.

• Russian text to be displayed on this unit

should be encoded in one of the

following character sets:

–Unicode (UTF-8, UTF-16)

– A character set other than Unicode that

is used in a Windows environment and

is set to Russian in the multi-language

setting

CAUTION

• Pioneer cannot guarantee compatibility

with all USB mass storage devices, and

assumes no responsibility for any loss of

data on media players, smartphones, or

other devices while using this product.

• Do not leave discs or a USB storage

device in any place that is subject to high

temperatures.

WMA files

Handling guidelines

Compressed audio

compatibility

File extension .wma

Bit rate 48 kbps to 320 kbps

(CBR), 48 kbps to 384

kbps (VBR)

Sampling frequency 32 kHz, 44.1 kHz, 48

kHz

13En

English

MP3 files

WAV files

• WAV file formats cannot be connected via

MTP.

FLAC files

• FLAC file formats cannot be connected

via MTP.

• FLAC files may not be playable,

depending on the encoder.

USB device

• There may be a slight delay when starting

playback of audio files on a USB storage

device with numerous folder hierarchies.

The user cannot assign folder numbers and

specify playback sequences with this unit.

Sequence of audio file depends on the

connected device.

Note that the hidden files in a USB device

cannot be played back.

Example of a hierarchy

Windows Media™

Audio Professional,

Lossless, Voice/DRM

Stream/Stream with

video

Not compatible

File extension .mp3

Bit rate 8 kbps to 320 kbps

(CBR), VBR

Sampling frequency 8 kHz to 48 kHz (32

kHz, 44.1 kHz, 48 kHz

for emphasis)

Compatible ID3 tag

version

1.0, 1.1, 2.2, 2.3, 2.4

(ID3 tag Version 2.x is

given priority over

Version 1.x.)

M3u playlist Not compatible

MP3i (MP3

interactive), mp3 PRO

Not compatible

File extension .wav

Quantization bits 8 and 16 (LPCM), 4

(MSADPCM)

Sampling frequency 16 kHz to 48 kHz

(LPCM), 22.05 kHz and

44.1 kHz (MS ADPCM)

File extension .flac

Sampling frequency 8/11.025/12/16/22.05/

24/32/44.1/48 [kHz]

Quantization bit rate 16 bit

Channel mode 1/2 ch

Playable folder

hierarchy

Up to eight tiers (A

practical hierarchy is

less than two tiers.)

Playable folders Up to 500

Playable files Up to 15 000

Playback of copyright-

protected files

Not compatible

Partitioned USB

device

Only the first partition

can be played.

Sequence of audio files

Folder

Compressed audio

file

to : Playback sequence

01 to 05: Folder number

WMA

Windows Media is either a registered

trademark or trademark of Microsoft

Corporation in the United States and/or

other countries.

This product includes technology owned

by Microsoft Corporation and cannot be

used or distributed without a license from

Microsoft Licensing, Inc.

FLAC

Foundation

Redistribution and use in source and

binary forms, with or without modification,

are permitted provided that the following

conditions are met:

–Redistributions of source code must

retain the above copyright notice, this list

of conditions and the following

disclaimer.

–Redistributions in binary form must

reproduce the above copyright notice,

this list of conditions and the following

disclaimer in the documentation and/or

other materials provided with the

distribution.

–Neither the name of the Xiph.org

Foundation nor the names of its

contributors may be used to endorse or

promote products derived from this

software without specific prior written

permission.

THIS SOFTWARE IS PROVIDED BY THE

CONTRIBUTORS “AS IS” AND ANY EXPRESS

OR IMPLIED WARRANTIES, INCLUDING, BUT

NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE

FOUNDATION OR CONTRIBUTORS BE

LIABLE FOR ANY DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, EXEMPLARY, OR

CONSEQUENTIAL DAMAGES (INCLUDING,

BUT NOT LIMITED TO, PROCUREMENT OF

SUBSTITUTE GOODS OR SERVICES; LOSS OF

USE, DATA, OR PROFITS; OR BUSINESS

INTERRUPTION) HOWEVER CAUSED AND

ON ANY THEORY OF LIABILITY, WHETHER

IN CONTRACT, STRICT LIABILITY, OR TORT

(INCLUDING NEGLIGENCE OR OTHERWISE)

ARISING IN ANY WAY OUT OF THE USE OF

THIS SOFTWARE, EVEN IF ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE.

Russian character chart

D: Display C: Character

14En

General

Power source: 14.4 V DC (10.8 V to 15.1 V

allowable)

Grounding system: Negative type

Maximum current consumption: 10.0 A

Dimensions (W × H × D):

DIN

Chassis: 178 mm × 50 mm × 97 mm

Nose: 188 mm × 58 mm × 17 mm

Chassis: 178 mm × 50 mm × 97 mm

Nose: 170 mm × 46 mm × 17 mm

Weight: 0.5 kg

Audio

Maximum power output:

50 W × 4

70 W × 1/2 Ω (for subwoofer)

Continuous power output:

22 W × 4 (50 Hz to 15 000 Hz, 5 %

THD, 4 Ω load, both channels driven)

Load impedance: 4 Ω (4 Ω to 8 Ω allowable)

Preout maximum output level: 2.0 V

Loudness contour: +10 dB (100 Hz),

+6.5 dB (10 kHz) (volume: –30 dB)

Equalizer (5-Band Graphic Equalizer):

Frequency: 80 Hz/250 Hz/800 Hz/2.5

kHz/8 kHz

Equalization range: ±12 dB (2 dB step)

Subwoofer (mono):

Frequency: 50 Hz/63 Hz/80 Hz/100

Hz/125 Hz/160 Hz/200 Hz

Slope: –12 dB/oct, –24 dB/oct

Gain: +6 dB to –24 dB

Phase: Normal/Reverse

USB

USB standard specification: USB 2.0 full

speed

Maximum current supply: 1 A

USB Class: MSC (Mass Storage Class)

File system: FAT12, FAT16, FAT32

MP3 decoding format: MPEG-1 & 2 Audio

Layer 3

WMA decoding format: Ver. 7, 7.1, 8, 9, 10,

11, 12 (2 ch audio) (Windows Media

Player)

FLAC decoding format: v1.3.0 (Free

Lossless Audio Codec)

WAV signal format: Linear PCM & MS

ADPCM (Non-compressed)

FM tuner

Frequency range: 87.5 MHz to 108.0 MHz

Usable sensitivity: 11 dBf (1.0 μV/75 Ω,

mono, S/N: 30 dB)

Signal-to-noise ratio: 72 dB (IEC-A network)

MW tuner

Frequency range: 531 kHz to 1 602 kHz

Usable sensitivity: 25 μV (S/N: 20 dB)

Signal-to-noise ratio: 62 dB (IEC-A network)

LW tuner

Frequency range: 153 kHz to 281 kHz

Usable sensitivity: 28 μV (S/N: 20 dB)

Signal-to-noise ratio: 62 dB (IEC-A network)

NOTE

Specifications and the design are subject

to modifications without notice.

Specifications

15En

English

2Ru

Перед началом эксплуатации............................................................ 3

Начало работы....................................................................................... 3

Радио ........................................................................................................ 6

USB/AUX ................................................................................................... 7

Настройки ............................................................................................... 8

Настройки FUNCTION ........................................................................... 8

Настройки AUDIO................................................................................... 9

Настройки SYSTEM ............................................................................. 10

Настройки ILLUMINATION................................................................. 10

Подключения/Установка .................................................................. 11

Дополнительная информация ........................................................ 14

Содержание

О данном руководстве:

В следующих инструкциях USB-накопитель и аудиопроигрыватель USB

называются “USB-устройство”.

3Ru

Русский

Благодарим Вас за покупку этого изделия компании PIONEER

Для обеспечения правильности эксплуатации внимательно прочитайте данное руководство

перед началом использования изделия. Особенно важно, чтобы Вы прочли и соблюдали

инструкции, помеченные в данном руководстве заголовками ПРЕДУПРЕЖДЕНИЕ и ВНИМАНИЕ.

Держите данное руководство под рукой для обращения к нему в будущем.

Дату изготовления оборудования можно определить по серийному номеру, который содержит

информацию о месяце и годе производства.

ПРЕДУПРЕЖДЕНИЕ

• Не пытайтесь самостоятельно производить установку или ремонт изделия. Установка

или ремонт изделия лицами, не обладающими специальными навыками и опытом

работы с электронным оборудованием и автомобильными аксессуарами, могут создать

опасность поражения электрическим током или иных инцидентов.

• Ни в коем случае не пытайтесь управлять устройством во время движения. Прежде чем

использовать органы управления устройством, необходимо съехать с дороги и припарковать

автомобиль в безопасном месте.

ВНИМАНИЕ

• Не допускайте попадания жидкости на устройство. Это может повлечь поражение

электрическим током. Кроме того, попадание жидкости в устройство может стать причиной его

выхода из строя, перегрева и появления дыма.

• Всегда сохраняйте уровень громкости достаточно низким, чтобы были слышны звуки извне.

При возникновении проблем

При неполадках в работе этого изделия свяжитесь с торговым представителем компании-

производителя или с ближайшим сервисным пунктом PIONEER.

MVH-171UB

* В этом руководстве данная кнопка именуется как DISP.

Пульт ДУ

Перед началом эксплуатации Начало работы

Основные операции

SRC (источник)/OFF

Кнопка отсоединения

Окно дисплея

Регулятор M.C.

(многозадачное управление)

BAND /DIMMER

Кнопка дисплея*

SRC (источник)

VOLUME +/–

MUTE

DISP (дисплей)

4Ru

Часто используемые операции

* Когда голубой/белый провод этого устройства подключен к терминалу релейного управления

автоматической антенны, антенна на автомобиле выдвигается при включении источника

сигнала этого устройства. Чтобы втянуть антенну, выключите источник сигнала.

Индикация на дисплее

Снимите переднюю панель во избежание кражи. Перед снятием панели

отсоедините кабели и устройства, подключенные к передней панели, и отключите

устройство.

Важно

• Оберегайте переднюю панель от сильных ударов.

• Не подвергайте переднюю панель воздействию прямых солнечных лучей и высоких

температур.

• Всегда храните снятую панель в защитном чехле или сумке.

Перед использованием снимите изоляционную пленку.

Операция

Назначение Главное устройство Пульт ДУ

Включение питания* Нажмите SRC/OFF для

включения питания.

Нажмите и удерживайте

SRC/OFF для выключения

питания.

Нажмите SRC для

включения питания.

Нажмите и удерживайте

SRC для выключения

питания.

Настройка громкости Поверните регулятор M.C..Нажмите VOLUME + или –.

Нажмите MUTE, чтобы

отключить звук. Нажмите

еще раз, чтобы включить

звук.

Выбор источника Несколько раз нажмите

SRC/OFF.

Несколько раз нажмите

SRC.

Изменение информации

на дисплее

Несколько раз нажмите

DISP.

Несколько раз нажмите

DISP.

Возврат к предыдущему

экрану/списку

Нажмите /DIMMER.Нажмите / для

выбора следующей/

предыдущей папки.

Возврат к обычному

дисплею из меню

Нажмите BAND.

–

Индикация Описание

Отображается при наличии нижнего уровня меню или папки.

Отображается, если нажата кнопка .

Отображается при настройке функции поиска локальных

радиостанций (стр. 9).

Отображается при получении программы с трафиком .

Отображается при получении уведомления о трафике (стр. 9).

Отображается, если установлена функция преобразования звука

(стр. 9).

Отображается при настройке произвольного/перемешанного

воспроизведения.

Отображается при установке повтора воспроизведения.

Снятие передней панели

Подготовка пульта ДУ

Индикация Описание

Снятие Установка

5Ru

Русский

ПРЕДУПРЕЖДЕНИЕ

• Храните батареи в недоступном для детей месте. В случае проглатывания батареи немедленно

обратитесь к врачу.

• Не подвергайте батареи и пульт ДУ чрезмерному воздействию тепла, например прямых

солнечных лучей и огня.

ВНИМАНИЕ

• В случае неправильной установки батарей существует опасность взрыва. При замене батареи

используйте батареи одинакового типа.

• Не храните батареи вместе с металлическими инструментами или предметами.

• В случае протекания батареи извлеките ее и немедленно тщательно протрите пульт ДУ. Затем

установите новую батарею.

• При утилизации отработанных батарей необходимо соблюдать государственные нормативы

или правила природоохранных учреждений, действующие в вашей стране/области.

Важно

• Не храните пульт ДУ под воздействием высоких температур или прямых солнечных лучей.

• Не допускайте падения пульта ДУ на пол, где он может застрять под педалью газа или тормоза.

После установки устройства поверните ключ зажигания в положение ON; на

дисплее отобразится установочное меню [SET UP :YES].

1 Нажмите регулятор M.C. .

Если в течение 30 секунд устройство не используется, установочное меню не

будет выводиться. Если вы хотите выполнить настройку позже, поверните M.C.,

чтобы выбрать [NO], и нажмите для подтверждения.

2 Поверните M.C. для выбора параметров, затем нажмите для подтверждения.

Для перехода к следующему пункту меню необходимо подтвердить выбор.

3 [QUIT :YES] отображается после выполнения всех настроек.

Чтобы вернуться к первому пункту установочного меню, поверните регулятор

M.C. для выбора [QUIT :NO],

затем нажмите повторно для подтверждения.

4 Нажмите регулятор M.C., чтобы подтвердить настройки.

ПРИМЕЧАНИЯ

• Вы можете отменить настройку параметра меню, нажав кнопку SRC/OFF.

• Настроить параметры меню можно в настройках SYSTEM (стр. 10) и настройках INITIAL (стр. 5).

1 Нажмите M.C. для отображения главного меню.

2 Поверните M.C. для выбора [SYSTEM], затем нажмите для подтверждения.

3 Поверните M.C. для выбора [DEMO OFF], затем нажмите для подтверждения.

4 Поверните M.C. для выбора [YES], затем нажмите для подтверждения.

1 Нажмите и удерживайте SRC/OFF, пока устройство не отключится.

2 Нажмите и удерживайте SRC/OFF, чтобы отобразить главное меню.

3 Поверните M.C. для выбора [INITIAL], затем нажмите для подтверждения.

4 Поверните M.C. для выбора параметра, затем нажмите для подтверждения.

Установочное меню

Замена батарей

Вставьте батарею CR2025 (3 В), соблюдая полярность

(+) и (–).

Элемент меню Описание

LANGUAGE Выбор языка для отображения текстовой информации с

сжатого аудиофайла.

[ENG]

(Английский),

[РУС]

(Русский),

[TUR]

(Турецкий)

CLOCK SET Настройка часов.

FM STEP Выбор шага настройки в FM-диапазоне (100 кГц или 50 кГц).

[100], [50]

Отмена демонстрационного дисплея (DEMO

OFF)

Настройки INITIAL

6Ru

Радиочастоты данного устройства предназначены для использования в Западной

Европе, Азии, Среднем Востоке, Африке и Океании. В других областях прием может

быть неудовлетворительным. Функция RDS (система радиоданных) работает

только в областях, где выполняется вещание сигналов RDS для FM-станций.

1 Нажмите SRC/OFF для выбора [RADIO].

2 Нажмите BAND для выбора полосы [FM1], [FM2], [FM3], [MW] или [LW].

3 Нажмите числовую кнопку (от1/ до 6/).

СОВЕТ

Кнопки / можно также использовать для выбора предварительно установленной

станции, если для параметра [SEEK] установлено значение [PCH] в настройках FUNCTION (стр. 9).

За каждой числовой кнопкой сохранена одна из шести радиостанций с наилучшим

качеством приема (с 1/ по 6/).

1 После выбора полосы нажмите регулятор M.C., чтобы отобразить главное

меню.

2 Поверните M.C. для выбора [FUNCTION], затем нажмите для подтверждения.

3 Поверните M.C. для выбора [BSM], затем нажмите для подтверждения.

Поиск станции вручную

После выбора полосы нажмите / для выбора станции.

Нажмите и удерживайте / , затем отпустите для поиска доступной

станции. Поиск остановится, когда устройство выполнит прием станции. Для

отмены поиска нажмите / .

ПРИМЕЧАНИЕ

Для параметра [SEEK] необходимо установить значение [MAN] в настройках FUNCTION (стр. 9).

Элемент меню Описание

FM STEP Выбор шага настройки в FM-диапазоне (100 кГц или 50 кГц).

[100], [50]

SP-P/O MODE Используется, когда полночастотный динамик подключен к

проводам вывода заднего динамика, а сабвуфер подключен

к выводу RCA.

[REAR/SUB.W]

[SUB.W/SUB.W] Используется, когда пассивный сабвуфер подключен

непосредственно к проводам вывода заднего динамика, а

сабвуфер подключен к выводу RCA.

[REAR/REAR] Используется, когда полночастотный динамик подключен к

проводам вывода заднего динамика выводу RCA Если

полночастотный динамик подключен к проводам вывода

заднего динамика и вывод RCA не используется, выберите

[REAR/SUB.W] или [REAR/REAR].

SYSTEM RESET Выберите [YES], чтобы инициализировать настройки.

Перезапуск устройства будет выполнен автоматически.

(Некоторые настройки устройства будут сохранены даже

после выполнения сброса.)

[YES], [CANCEL]

Радио

Прием сохраненных станций

Память для записи избранных станций (BSM)

Страница загружается ...

Pioneer MVH-171UB Руководство пользователя

Бренд: Pioneer

Модель: MVH-171UB

Тип: Руководство пользователя

Скачать PDF

сообщить о нарушении

на других языках

English: Pioneer MVH-171UB User manual

Pioneer MVH-171UB Руководство пользователя

Pioneer MVH-171UB Руководство пользователя

на других языках

Похожие модели бренда