Key D : decreases motor speed / Reset; decreases motor speed to zero
(stopping); in any case however, after approximately 1 minute, the hood
resumes automatic operation at the speed set by the sensor. Whenever the
key is pressed during the display of fi lter alarms, a RESET occurs, and the
counting of the hours resumes again.
Key E : increases motor speed; in any case however, after approximately
1 minute, the hood resumes automatic operation at the speed set by the
sensor.
Modifi cation of sensor sensitivity: sensor sensitivity can be modifi ed by
operating as follows:
- stop the hood by pressing key B. – Simultaneously press keys D and E
(the sensor’s sensitivity index will appear on the display) - Pressing keys D
or E, the sensor’s sensitivity will either increase or decrease (1 : minimum
sensitivity / 9: maximum sensitivity). – whenever the power supply is
interrupted, the sensor will resume operation with a sensitivity index of 5.
Warning: in order to avoid damaging the sensor, never use silicone products
near the hood!
OPERATION AS TRADITIONAL HOOD:
Key A : switches the lights on/off .
Display C : - indicates the motor speed selected (from 1 to 4); - indicates
the operation of the Timer when the number is fl ashing; - indicates fi lter
alarms whenever the central segment is illuminated or fl ashing.
Key D : decreases motor speed / Stop / Reset; decreases motor speed to
zero (stopping). Whenever the key is pressing during fi lter alarm display, a
RESET occurs, and the counting of the hours resumes again.
Key E : enables the motor / increases motor speed /TIMER. Pressing
this key starts the motor (at the latest speed set); pressing the key again
increases motor speed, while keeping the key pressed down for a few
seconds enables the TIMER, and 5 minutes later the motor will stop (while
the number of speed setting selected will simultaneously begin fl ashing on
the display); the Timer will remain enabled if motor speed is changed. In
order to disable the Timer, press the key again.
Controls of Fig. 22
Key L: light switch.
Key 1 : B = Motor ON/OFF switch - Speed I
Key 2: B = Motor ON/OFF switch - Speed I
Key 3: B = Motor ON/OFF switch - Speed I
Key 4: B = Motor ON/OFF switch - Speed I
Filter alarm: after about 30 hours of operation, with the motor off , the
speed keys (keys 1, 2, 3 and 4) fl ash for 30 seconds to indicate the grease
fi lters need cleaning. After cleaning the grease fi lters (and/or replacing the
charcoal fi lters), restart the hour counter (RESET) by pressing key C during
fi lter alarm display.
Timer 5’; the timer can be started (switch-off delayed by 5 minutes) by
pressing one of the speed keys for 2 seconds(key 1, 2, 3 or 4) when the
motor is running; the selected speed key starts fl ashing.
Controls of Fig. 23
Key L: light switch.
Key 1: activates/deactivates the sensor (AUTOMATIC or MANUAL mode).
In Automatic mode the sensor is activeand the speed of the motor increases
or decreases depending on the smoke.- signals the fi lter alarm (with motor
off )
Key 2: Motor ON/OFF switch - Speed I
Key 3: Motor ON/OFF switch - Speed II
Key 4: Motor ON/OFF switch - Speed III
Filter alarm: after about 30 hours of operation, with the motor off , the
speed keys (keys 1, 2, 3 and 4) fl ash for 30 seconds to indicate the
antigrease fi lters need cleaning. After cleaning the anti-grease fi lters (and/or
replacingthe charcoal fi lters), restart the hour counter (RESET) by pressing
one of the speed keys for 2 seconds during fi lter alarm display.
SENSOR SENSITIVITY: When the sensor is on, the hood automatically
starts working when any smell, vapour, smoke or heat is detectedduring
cooking. The sensor sensitivi-ty can be changed according to need. For
example: very sensitive when using an electric hob or little sensitive when
using a gas hob. Change thesensitivity by simultaneously pressing key L
and key 1. The sensitivity selected will be set. Using the keys 2,3,4 you can
set the desired sensitivity. Store the new sensitivity by pressing key1.
Attention: To prevent damaging the sensor, do not use silicone products
near the hood!
Controls of Fig. 24
Button A: Turns the lights on/off . If held down for about 2” when the fi lter
alarm is active, it resets the hour counter.
Button B: Activates/deactivates the “Automatic” function.
Light S – Filter alarm: When the light comes on, it indicatesthat 30 h of use
have elapsed; it remains on for 30”. When the light S fl ashes, it means that
about 120 h of operationhave elapsed. The fi lter reset is indicated only
when the motor is off , both in manual and automatic mode.
Automatic operation with sensor: when the button B is pressed, the
automatic function is activated. This is indicated by the corresponding LED
comingon. When the LED B fl ashes, it means that the sensor is waiting for
data.
Modifying sensor sensitivity: while in manual mode and with the motor off ,
simultaneously press the buttons B and C. At this point, the set sensitivity
is indicated by the LED C, D or E coming on. To set the desired sensitivity
press one of the buttons C, Dor E (min, med, max). Press B again to store
it.Press button B once again to go to manual mode.
Operation as traditional hood: if in automatic mode, press the button B to
change to manual mode; the LED B goes off .Press one of the buttons C, D
or E to start the motor in 1st, 2nd or 3rd speed, respectively. Hold the same
buttondown for 2” to turn off the motor.
Controls of Fig. 25
P1: It turns on an off the light.
P2: It starts the engine setting it to the fi rst speed (the icon is highlighted).
Other speed icons remain inactive.
P3: It starts the engine setting it to the second speed (the icon is
highlighted). Other speed icons remain inactive.
P4: It starts the engine setting it to the third speed (the icon is highlighted).
Other speed icons remain inactive.
P5: It starts the engine setting it to the fourth speed (the icon is blinking).
Other speed icons remain inactive. The maximum speed is set to be
maintained for maximum 5 minutes, after this time the speed will be
automatically adjusted to the third speed.
P6: It starts the timer (the icon is highlighted). By running the timer (5
minutes), the engine stops automatically after 5 minutes.
P7: FILTER ALARM. After 30 hours of operation the icon is highlighted to
indicate that the fi lter should be cleaned.
After 120 hours of operation the icon is highlighted to indicate that the
grease fi lter should be cleaned and the charcoal fi lters - replaced.
To RESET the alarm, press the icon while it is highlighted (or while it is
blinking).
Controls of Fig. 26-27
Button TC1 (Lights): Switches main light ON/OFFWhen the main light is on,
BL1 changes colour and becomes active.When the button is pressed for
more than a second, it switches the courtesy lights (optional) on/off .
Button TC2 (Motor-V1): Motor ON/OFF - Activates the motor at 1st speed.
Button TC3 (Motor-V2)Activates the motor at 2nd speed.
Button TC4 (Motor-V3)Activates the motor at 3rd speed.
Button TC5 (Motor-V4)Activates the motor at 4th speedMaximum
speed is timed at a maximum of 5 minutes, after which 3rd speed is set
automatically.When the motor is active, the LED of the last selected button
(TC2-TC5) active to signal which speed has been set.
Button TC6 (TIMER auto power off 5 min.)Activates the TIMER function
at the speed that has already been selectedIf the motor is NOT active,
it switches on the motor at the 1st speed and activates the TIMER
functionWhen the TIMER function is active, BL6 becomes active.
30h fi lter ALARM: after 30 hours of operation, an alarm switches on to
signal the need for anti-grease fi lter cleaning.The fi lter alarm, when active,
is displayed for 30 sec each time the motor is deactiva-ted:BL6 remains
ON.During this period, it is possible to reset the alarm by pressing the TC6
button for longer than a second.
120h fi lter ALARM: after 120 hours of operation, an alarm switches on to
signal the need for active carbon fi lter (optional) replacement.The fi lter
alarm, when active, is displayed for 30 sec each time the motor is deactiva-
ted:BL6 lighting blinking.During this period, it is possible to reset the alarm
by pressing the TC6 button for longer than a second.
Work Time Limit: if the hood is left on (lights and/or motor), after 10 hours in
the absence of commands from the user, it will automatically switch to OFF
condition with all services switched off .
Buzzer: the Buzzer emits a “beep” each time that a command is set from
the keyboard or remote control (optional).
WARNING - All fl ashing keys (Fig.27): the unit is equipped with infrared
sensor controls that, if exposed to direct sunlight may not work properly;
use curtains or other devices to shield the sunlight.
Controls of Fig. 28-29
Button TC1 (Lights): Switches main light ON/OFFWhen the main light is on,
BL1 changes colour and becomes active.When the button is pressed for
more than a second, it switches the courtesy lights (optional) on/off .
Button TC2 (Motor-V1)Motor ON/OFF - Activates the motor at 1st speed.
Button TC3 (Motor-V2) Activates the motor at 2nd speed.
Button TC4 (Motor-V3)Activates the motor at 3rd speed.
Button TC5 (Motor-V4)Activates the motor at 4th speedMaximum
speed is timed at a maximum of 5 minutes, after which 3rd speed is set
automatically.When the motor is active, the LED of the last selected button
(TC2-TC5) active to signal which speed has been set.
Button TC6 (Auto ASC)Activates/deactivates the automatic ASC function.In
this mode, motor speed increases or decreases depending on the quantity
of smoke and odours being produced under the hood. When the function is
active, BL6 becomes active.Each time that the motor changes speed, either
automatically or forced by the user, BL6 lighting blinking for a few seconds.
30h fi lter ALARM: After 30 hours of operation, an alarm switches on to
signal the need for anti-grease fi lter cleaning.The fi lter alarm, when active,
is displayed for 30 sec each time the motor is deactivated:BL6 remains
ON.During this period, it is possible to reset the alarm by pressing the TC6
