Yamaha BRK-TV2 Инструкция по установке

Yamaha
Бренд
Yamaha
Модель
BRK-TV2
Тип
Инструкция по установке
MOUNTING ACCESSORY
BRK-TV2 Installation Manual
EN
© 2023 Yamaha Corporation
Published 09/2023
IP-A0
BRK-TV2 is a mounting bracket for attaching video conference system CS-800/CS-500 to a TV.
Installation conditions for BRK-TV2
This bracket can be attached to the VESA mount of a 40" to 90" TV. Make sure that the TV to which the bracket will be mounted meets all
three of the following conditions.
X
A
B
Y
Z
1. Spacing between screw holes (A and B must be
any of the following measurements.)
A = 100 / 200 / 300 / 400mm
B = 100 / 200 / 300 / 400 / 600mm
2. TV height
Z = 490mm or more
3. Distance from edge of TV to VESA hole
When installing the device above the TV:
X = 980 mm or less
When installing the device below the TV:
Y = 980 mm or less
Before installation
Before installing BRK-TV2 and the device, we recommend connecting the cables to the device and pairing the remote control. For the
pre-installation procedure for the device, refer to “Procedures preparing for use” in the User Guide for the corresponding model.
About this manual
•This manual provides details on installing BRK-TV2. For details on using and connecting the CS-800/CS-500, refer to the corresponding
User Guide.
• The illustrations in this manual are for instructional purposes only.
• Be sure to have the mounting bracket installed by the dealer where you purchased the product or a professional
contractor.
• After installation, make sure that the device is firmly secured. Also, regularly check that there is no possibility of the
device falling or tipping over. We cannot be held responsible for accidents caused by incorrect installation.
• After installation, do not lean against the device or apply a strong force to it from above. If the device falls, injuries or
damage may result.
WARNING
• The installation procedure may vary depending on the specifications of the metal fittings on the TV stand.
• For details on assembling the TV stand and mounting the TV to it, follow the instructions in the manual for the TV stand.
• The TV should be mounted to the TV stand by two or more people.
NOTICE
• Neither a TV stand nor wall-mounted TV stand is included.
• The VESA standards are international standards that define the spacing between screw holes used when attaching
video equipment, such as TVs, to wall mounts and TV stands.
NOTE
Items to prepare
1. Items included with BRK-TV2
Mounting bracket
A B C D
× 1× 2
D is used when installing the device onto a large TV. (Refer to step 3 in “Installation procedure”.)
Spacers/screws
E F G H
or
G H
× 4× 16 × 4
or × 4
× 4
× 4
or × 4
× 4
Ø25 × t18 mm M4 × 10 mm
with washer
M6 × 12 mm or
M6 × 30 mm
Flat washer (M6)
Spring washer (M6)
M8 × 15 mm or
M8 × 35 mm
Flat washer (M8)
Spring washer (M8)
Use E depending on the
configuration of the TV stand.
Use only four of G. Use screws of the size suitable for the TV stand.
× 1× 1
2. Wall mounting bracket
When installing CS-800
Use the wall mounting bracket included with CS-800.
I J
× 1
× 1
Wall mounting bracket M3 × 8 mm
When installing CS-500
Use the separately sold wall mounting bracket BRK-WL1.
I J
× 1
× 1
Wall mounting bracket 1/4 inch
3. Items to prepare yourself
K VESA-compatible TV stand (or wall mount)
L Phillips screwdriver or electric screwdriver
M Measuring tape
Included with CS-800
Separately sold BRK-WL1
CS-500
Installation procedure
The illustrations in this “Installation procedure” are for “When installing the device above the TV”.
When installing the device below the TV
Step 2: Turn the part assembled in step 1 upside down before installing it.
Steps 5 and 6: Turn the part assembled in step 2 upside down before installing it.
1
F× 4
A
C
4 Install parts B and K aligned with the screw holes in the TV.
Depending on the configuration of the TV stand, tighten the parts together with E between them to adjust the spacing to the TV.
B× 2
E× 4
G× 4
K
H× 4
Flat washer
H× 4
Spring washer
TV
Location where device
is to be installed.
Screw holes
5When the distance measured in step 3 is
505mm or less
Attach the part from step 2 directly to B.
When the distance measured in step 3 is 506mm
or more
Attach D to B, and then attach the part from step 2 to D.
B× 2B× 2
D
F× 4
F× 8
2
2
2 CS-800 CS-500
F× 4F× 2
I
I
11
* When installing the device below the TV,
use the lower screw holes.
3
Measure the distance from the edge of the TV to the VESA hole. (This measurement will be used in step 5.)
a
b
When installing the device above the TV: a
Measure the distance from the top edge of the TV to the lower
VESA hole.
When installing the device below the TV: b
Measure the distance from the bottom edge of the TV to the upper
VESA hole.
When 505 mm or less: Extension D is not required.
When 506 mm or more: Extension D is required.
6 CS-800
I
I
J
2
2
CS-800
(back)
CS-500
CS-800
(front)
Tighten with a long
screwdriver.
J
  • Page 1 1
  • Page 2 2

Yamaha BRK-TV2 Инструкция по установке

Yamaha
Бренд
Yamaha
Модель
BRK-TV2
Тип
Инструкция по установке
Скачать PDF
сообщить о нарушении

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ

на других языках

Похожие модели бренда

Модели других брендов