3
English
Do not open
• This product contains no user-serviceable parts. Do not
attempt to disassemble the internal parts or modify them in
any way.
Water warning
• Do not expose the product to rain, use it near water or in
damp or wet conditions, or place on it any containers (such
as vases, bottles or glasses) containing liquids which might
spill into any openings.
• Never insert or remove an electric plug with wet hands.
Fire warning
• Do not place any burning items or open flames near the
product, since they may cause a fire.
Hearing loss
• Before turning the power of all devices on or off, make sure
that all volume levels are set to the minimum. Failing to
do so may result in hearing loss, electric shock, or device
damage.
• When turning on the AC power in your audio system,
always turn on the product LAST, to avoid hearing loss and
speaker damage. When turning the power off, the product
should be turned off FIRST for the same reason.
CAUTION
Always follow the basic precautions listed below to
avoid the possibility of physical injury to you or others.
These precautions include, but are not limited to, the
following:
Power supply
• When removing the electric plug from the product or an
outlet, always hold the plug itself and not the cord. Pulling
by the cord can damage it.
Location and connection
• Do not place the product in an unstable position or
a location with excessive vibration, where it might
accidentally fall over and cause injury.
• Keep this product out of reach of children. This product is
not suitable for use in locations where children are likely to
be present.
• To ensure proper heat dissipation of the product when
mounting this speaker in a rack, make sure that there
is adequate space around the product: at least 30 cm
above, 10 cm at the sides and 20 cm behind. Inadequate
ventilation can result in overheating, possibly causing
damage to the product(s), or even fire. For normal
ventilation during use, remove the rear of the rack or open
a ventilation hole.
• Secure the product with non-skid pads, etc. to prevent it
from moving. If the product is placed unsecured on a table
or platform, it will move gradually due to its vibration and
may fall off the table, causing damage or injury.
• Do not place the product in a location where it may come
into contact with corrosive gases or salt air. Doing so may
result in malfunction.
• Before moving the product, remove all connected cables.
• Do not press the rear panel of the product against the wall.
Doing so may cause the plug to come in contact with the
wall and detach from the power cord, resulting in short
circuiting, malfunction, or even fire.
Maintenance
• Remove the power plug from the AC outlet when cleaning
the product.
Handling caution
• Do not insert your fingers or hands in any gaps or openings
on the product (ports).
• Do not rest your weight on the product or place heavy
objects on it.
• Do not operate the product if the sound is distorting.
Prolonged use in this condition could cause overheating
and result in fire.
Notice
To avoid the possibility of malfunction/damage to the product
or damage to other property, follow the notices below.
Handling and maintenance
• Do not use the product in the vicinity of a TV, radio, or other
electric products. Otherwise, the product, TV, or radio may
generate noise.
• Do not expose the product to excessive dust or vibration,
or extreme cold or heat, in order to prevent the possibility
of panel disfiguration, unstable operation, or damage to the
internal components.
• Do not install in locations where temperature changes are
severe. Otherwise, condensation may form on the inside or
the surface of the product, causing it to break.
• If there is reason to believe that condensation might have
occurred, leave the product for several hours without
turning on the power until the condensation has completely
dried out, in order to prevent possible damage.
• Do not touch the speaker driver unit, since it might cause
malfunction.
• Do not place vinyl, plastic or rubber objects on the product,
since this might cause alteration or discoloration of the
panel.
• When cleaning the product, use a dry and soft cloth.
Do not use paint thinners, solvents, cleaning fluids, or
chemical-impregnated wiping cloths, since this might
cause alteration or discoloration.
Information
About functions/data bundled with the product
• XLR-type connectors are wired as follows (IEC60268
standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (−).
About this manual
• The illustrations as shown in this manual are for instructional
purposes only.
• The company names and product names in this manual are
the trademarks or registered trademarks of their respective
companies.
PA_en_12 2/2
