Yamaha NX-E200 Руководство пользователя

Бренд: Yamaha

Модель: NX-E200

Категория: Акустические системы

Тип: Руководство пользователя

Yamaha NX-E200 — это двухполосная акустическая система фазоинверторного типа с магнитным экранированием. 13-сантиметровый НЧ-динамик и 2,5-сантиметровый ВЧ-динамик с куполом обеспечивают частотный диапазон от 55 Гц до 28 кГц и чувствительность 87 дБ/2,83 В/м. Система имеет номинальную входную мощность 60 Вт и максимальную входную мощность 110 Вт. Импеданс акустики составляет 6 Ом. Размеры каждого громкоговорителя — 186 x 300 x 222 мм, вес — 4 кг. В комплект входят два 4-метровых кабеля для подключения.

OWNER’S MANUAL

MODE D’EMPLOI

NX-E200

Speaker System

Systeme D’enceintes

Thank you for selecting this Yamaha NX-E200 speaker system.

PRECAUTIONS

Read this before using the speakers.

• To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

• Install the speakers in a cool, dry, clean place – away

from windows, heat sources, sources of excessive

vibration, dust, moisture and cold. Avoid sources of

humming (transformers, motors). To prevent fire or

electrical shock, do not expose the speakers to rain or

water.

• To prevent the enclosure from warping or discoloring,

do not place the speakers where they will be exposed

to direct sunlight or excessive humidity.

• Do not place the following objects on the speakers:

Glass, chine, etc.

If glass etc. falls by vibrations and breaks, it may

cause personal injury.

A burning candle etc.

If the candle falls by vibrations, it may cause fire

and personal injury.

A vessel with water in it

If the vessel falls by vibrations and water spills, it

may cause damage to the speakers, and/or you may

get an electrical shock.

• Do not place the speakers where foreign objects such

as water drips might fall. It might cause a fire, damage

to the speakers, and/or personal injury.

• Do not place the speakers where they are liable to be

knocked over or struck by falling objects. Stable

placement will also ensure better sound performance.

• Placing the speakers on the same shelf or rack as the

turntable can result in feedback.

• Any time you note distortion, reduce the volume

control on your receiver to a lower setting. Never

allow your receiver to be driven into “clipping”.

Otherwise the speakers may be damaged.

• When using a receiver with a rated output power

higher than the nominal input power of the speakers,

care should be taken never to exceed the speakers'

maximum input.

• Do not attempt to clean the speakers with chemical

solvents as this might damage the finish. Use a clean,

dry cloth.

• Do not attempt to modify or fix the speakers. Contact

qualified YAMAHA service personnel when any

service is needed. The cabinet should never be opened

for any reasons.

• Secure placement or installation is the

owner's responsibility.

YAMAHA shall not be liable for any accident

caused by improper placement or installation

of speakers.

CONNECTION TO YOUR RX-E200

RECEIVER

BEFORE MAKING CONNECTIONS, MAKE SURE

THAT THE RX-E200 RECEIVER IS SWITCHED

OFF.

• When this unit is connected to the RX-E200 receiver,

refer also to the owner's manual supplied with the

receiver.

■ CONNECTIONS

• Connect the screw-type input terminals at the rear of

the speakers to the speaker output terminals of the

receiver with the provided speaker cables.

• One side of the speaker cable is red and the other side

is black. Connect the (+) terminals on the receiver and

speakers using the red side. Connect the (–) terminals

on both components using the black side of the cable.

• Connect one speaker to the left (marked L) terminals

of the receiver, and the other to the right (marked R)

terminals. Make sure not to reverse polarity (+, –).

If a speaker is connected with reverse polarity, the

sound will be unnatural and lack bass.

RX-E200

Tighten

Loosen

Red (+)

Red line

Speaker (L)Speaker (R)

Black line

Red line

Speaker output terminals

of the receiver

Black (–)

• Place the speakers on a sturdy, vibration-free surface.

You may not be able to obtain good bass quality when

the speakers are placed directly on the floor. Put a

block, etc. under the speakers.

• Better stereo images will be obtained when the

speakers are slightly angled in towards the listening

position.

The front cover is fastened to the enclosure at four point

and can be removed if desired. To remove the cover, hold

on to both sides and slowly pull straight away from the

speaker.

To reattach, line up the four pegs on the inner surface of

the cover with the four corresponding holes on the

speaker and push gently.

REMOVING THE FRONT COVER

Type ............................. 2-way bass-reflex speaker system

(Magnetic shielding type)

Driver ...........................................13 cm (5") cone woofer

2.5 cm (1") dome tweeter

Nominal Input Power ............................................... 60 W

Maximum Input Power ........................................... 110 W

Impedance.................................................................... 6 Ω

Frequency Response ................................ 55 Hz – 28 kHz

Sensitivity ................................................ 87 dB/2.83 V/m

Crossover Frequency ............................................... 3 kHz

Dimensions (W x H x D) ................. 186 x 300 x 222 mm

(7-5/16" x 11-13/16" x 8-3/4")

Weight ...........................................4 kg (8 lbs. 13 oz.) x 2

Accessories ..................................Speaker cable (4 m) x 2

* Please note that all specifications are subject to change

without notice.

* Care should be taken not to exceed the input power

values noted above.

SPECIFICATIONS

Note

When the cover is removed, be sure not to

touch the speaker units with your hands or to

exert excessive force with tools.

PLACING THE SPEAKERS

How to connect:

1 Loosen the knob.

2 Insert the bare wire. [Remove the insulation coating at

the extremity of each speaker cable by twisting the

coating off.]

3 Tighten the knob and secure the cable.

Test the firmness of the connection by pulling lightly

on the cable at the terminal.

Note

Do not let the bare speaker wires touch each

other as this could damage the speaker or the

amplifier, or both of them.

Good No Good

Note

These speakers feature a magnetically shielded

design, but there is still a chance that placing

them too close to a TV set might impair picture

color. Should this happen, move the speakers

away from the TV set.

Printed in China V685700

Yamaha NX-E200 Руководство пользователя

Бренд: Yamaha

Модель: NX-E200

Категория: Акустические системы

Тип: Руководство пользователя

Скачать PDF

сообщить о нарушении

на других языках

English: Yamaha NX-E200 User manual
français: Yamaha NX-E200 Manuel utilisateur
italiano: Yamaha NX-E200 Manuale utente
español: Yamaha NX-E200 Manual de usuario
Deutsch: Yamaha NX-E200 Benutzerhandbuch
Nederlands: Yamaha NX-E200 Handleiding
português: Yamaha NX-E200 Manual do usuário
dansk: Yamaha NX-E200 Brugermanual
polski: Yamaha NX-E200 Instrukcja obsługi
čeština: Yamaha NX-E200 Uživatelský manuál
svenska: Yamaha NX-E200 Användarmanual
Türkçe: Yamaha NX-E200 Kullanım kılavuzu
suomi: Yamaha NX-E200 Ohjekirja
română: Yamaha NX-E200 Manual de utilizare

Yamaha NX-E200 Руководство пользователя

Yamaha NX-E200 Руководство пользователя

на других языках

Похожие модели бренда