Yamaha NS-10MMTS Инструкция по применению

Тип
Инструкция по применению
English
E-1
Read this before using the speakers.
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install the speakers in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold. Avoid sources of humming
(transformers, motors). To prevent fire or electrical shock,
do not expose the speakers to rain or water.
To prevent the enclosure from warping or discoloring, do
not place the speakers where they will be exposed to
direct sunlight or excessive humidity.
Do not place the following objects on the speakers:
Glass, china, etc.
If glass etc. falls by vibrations and breaks, it may cause
personal injury.
A burning candle etc.
If the candle falls by vibrations, it may cause fire and
personal injury.
A vessel with water in it
If the vessel falls by vibrations and water spills, it may
cause damage to the speakers, and/or you may get an
electric shock.
Do not place the speakers where foreign objects such as
water drips might fall. It might cause a fire, damage to
the speakers, and/or personal injury.
Do not place the speakers where they are liable to be
knocked over or struck by falling objects. Stable
placement will also ensure better sound performance.
PRECAUTIONS
Thank you for selecting this YAMAHA NS-10MMTS speaker system.
Placing the speakers on the same shelf or rack as the
turntable can result in feedback.
Never put a hand or a foreign object into the port located
on the rear of the speaker as this might cause personal
injury and/or damage to the speaker.
When moving the speaker, do not hold the port as it
might cause personal injury and/or damage to the
speaker.
Any time you note distortion, reduce the volume control
on your amplifier to a lower setting. Never allow your
amplifier to be driven into “clipping”. Otherwise the
speakers may be damaged.
When using an amplifier with a rated output power higher
than the nominal input power of the speakers, care should
be taken never to exceed the speakers’ maximum input.
Do not attempt to clean the speakers with chemical solvents
as this might damage the finish. Use a clean, dry cloth.
Do not attempt to modify or fix the speakers. Contact
qualified YAMAHA service personnel when any service
is needed. The cabinet should never be opened for any
reasons.
Secure placement or installation is the owner’s
responsibility.
YAMAHA shall not be liable for any accident caused
by improper placement or installation of speakers.
Check that the following items are included.
Speaker cable (10m) x 1 Mounting bracket x 1 Screw x 2 Pad x 2
ACCESSORIES
NS-10MMTS
Speaker System
OWNER’S MANUAL
G
E-2
Place the speaker precisely between the rear speakers as
shown in the figure below.
To mount the speaker on a wall by using
the provided mounting bracket
1 Attach the bracket to the rear of the speaker by using the
provided screws. Remove the provided pads from the
backing sheet and put them at the lower corners of the
speaker.
PLACING THE SPEAKER
2
Fasten screws into a firm wall or wall support as shown
in the figure, and hang the holes of the mounting
bracket on the protruding screws.
* Make sure that the screws are securely caught by the
narrow parts of the holes.
WARNING
This speaker weighs 1.5 kg (3 lbs. 5 oz.). Do not
mount it on thin plywood or a wall with soft surface
material. If mounted, the screws may come out of the
flimsy surface and the speaker may fall. This
damages the speaker or causes personal injury.
Do not install the speaker to a wall with nails,
adhesives, or any other unstable hardware. Long-
term use and vibrations may cause it to fall.
To avoid accidents resulting from tripping over loose
speaker cable, fix it to the wall.
This speaker features a magnetically shielded design,
but there is still a chance that placing it too close to a
TV set might impair picture color. Should this
happen, move the speaker away from the TV set.
Rear R
60 mm
You can also use the screw holes on the bottom of the
speaker for installing the speaker on commericially
available speaker stand (if you do not use the provided
mounting bracket.)
A screw with a diameter of 4 mm can be
used.
(Hole depth : 10 mm)
Wall/ wall
support
Tapping screw (3.5–4 mm)
(Available at the hardware
store)
40 mm
Min.
20 mm
3 mm
Pad
Screw
Mounting bracket
Rear L
Subwoofer
Center
Main L
Main R
NS-10MMTS
English
E-3
REAR
CENTER
+
CONNECTIONS TO YOUR AMPLIFIER
Amplifier or
Receiver
Tighten
NS-10MMTS
Before making connections, make sure that the amplifier is switched off.
CONNECTIONS
Connect the screw-type input terminals at the rear of the
speaker to the speaker output terminals of the amplifier
(or receiver) with the speaker cable.
Connect the (+) terminals on the amplifier (or receiver)
and the speaker using one side of the cable. Connect the
(–) terminals on both components using the other side of
the cable.
Connect the speaker to the rear center terminals of your
amplifier (or receiver), making sure not to reverse the
polarity (+, –). If the speaker is connected with reversed
polarity, the sound will be unnatural and lack bass.
How to connect:
1 Loosen the knob.
2 Remove the insulation coating at the extremity of each
speaker cable by twisting the coating off.
3 Insert the bare wire.
4 Tighten the knob and secure the cable.
Test the firmness of the connection by pulling lightly on
the cable at the terminal.
Note
Do not let the bare speaker wires touch each other as
this could damage the speaker or the amplifier, or both
of them.
Loosen
Black ()
When using a banana plug
1 Remove the cover by pulling it toward you.
2 Tighten the terminal knob.
3 Simply insert the banana plug into the terminal.
Banana plug
2
1
3
Red (+)
+
E-4
SPECIFICATIONS
Type ............................. 2-way bass reflex speaker system
Magnetic shielding type
Driver ........................................ 9 cm (3-1/2”) cone woofer
2.5 cm (1”) balanced dome tweeter
Impedance ................................................................... 6
Frequency Response ................................75 Hz to 33 kHz
Nominal Input Power .................................................. 40 W
Maximum Input Power.............................................. 100 W
Sensitivity ...................................................88 dB/2.83 V/m
Crossover Frequency ................................................. 7kHz
Dimensions (WxHxD) ......................... 107 x 191 x 141 mm
(4-3/16” x 7-1/2” x 5-9/16”)
Weight .................................................. 1.5 kg (3 lbs. 5 oz.)
Accessories ................................. Speaker cable (10m) x 1
Mounting bracket x 1
Screw x 2
Pad x 2
Specifications are subject to change without notice due
to product improvements.
Care should be taken not to exceed the input power
values noted above.
REMOVING THE FRONT COVER
The front cover is fastened to the enclosure at four points
and can be removed if desired. To remove the cover, hold
on to both sides and slowly pull straight away from the
speaker. To reattach, line up the four holes on the inner
surface of the cover with the four corresponding pegs on
the speaker and push gently.
Note
When the cover is removed, take care not to touch the
speaker units with your hands or to exert excessive
force with tools.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, 25462 RELLINGEN, BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VASTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
V921090
Printed in Indonesia
NS-P70 FRE(02.2.27)b 02.2.27, 8:12 PM8
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Yamaha NS-10MMTS Инструкция по применению

Тип
Инструкция по применению

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ