Pioneer MVH-08UBG Руководство пользователя

Категория
Мультимедиа-приемники для автомобилей
Тип
Руководство пользователя

Это руководство также подходит для

H:\PDF-OUT\127075006696_KM636UW\010COV_KM636UW.fm
English Русский
MVH-08UB/MVH-08UBG
127075006696
DIGITAL MEDIA RECEIVER
ЦИФРОВОЙ МЕДИАРЕСИВЕР
MVH-08UB
MVH-08UBG
Owners Manual
Руководство пользователя
_127075006696_artwork.book Page 1 Monday, July 27, 2015 10:01 AM
2
H:\PDF-OUT\127075006696_KM636UW\020Chapter_EN.fm
MVH-08UB/MVH-08UBG
127075006696
En
Before You Start ......................................................................... 2
Getting Started .......................................................................... 3
Radio ............................................................................................ 5
USB/AUX ...................................................................................... 5
Settings........................................................................................ 7
FUNCTION settings .................................................................. 7
AUDIO settings.......................................................................... 7
SYSTEM settings ....................................................................... 8
Connections/Installation.......................................................... 9
Additional Information........................................................... 12
About this manual:
In the following instructions, a USB memory or USB audio player are referred
to as “USB device”.
Table of Contents
Thank you for purchasing this PIONEER product
To ensure proper use, please read through this manual before using this product. It is
especially important that you read and observe WARNINGs and CAUTIONs in this manual.
Please keep the manual in a safe and accessible place for future reference.
Private households in the member states of the EU, in Switzerland and Norway may return
their used electronic products free of charge to designated collection facilities or to a
retailer (if you purchase a similar new one).
For countries not mentioned above, please contact your local authorities for the correct
method of disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment,
recovery and recycling and thus prevent potential negative effects on the environment and
human health.
WARNING
Do not attempt to install or service this product by yourself. Installation or servicing
of this product by persons without training and experience in electronic equipment
and automotive accessories may be dangerous and could expose you to the risk of
electric shock, injury or other hazards.
Do not attempt to operate the unit while driving. Make sure to pull off the road and park
your vehicle in a safe location before attempting to use the controls on the device.
CAUTION
Do not allow this unit to come into contact with moisture and/or liquids. Electrical shock
could result. Also, damage to this unit, smoke, and overheating could result from contact
with liquids.
Always keep the volume low enough to hear outside sounds.
Before You Start
If you want to dispose this product, do not mix it with general household waste. There is a
separate collection system for used electronic products in accordance with legislation
that requires proper treatment, recovery and recycling.
_127075006696_artwork.book Page 2 Monday, July 27, 2015 10:01 AM
3
H:\PDF-OUT\127075006696_KM636UW\020Chapter_EN.fm
MVH-08UB/MVH-08UBG
127075006696
En
English
If you experience problems
Should this unit fail to work properly, please contact your dealer or nearest authorized
PIONEER Service Station.
MVH-08UB/08UBG
Frequently used operations
Getting Started
Basic operation
Purpose Operation
Turn on the power* Press SRC/OFF to turn on the power.
Press and hold SRC/OFF to turn off the
power.
Adjust the volume Turn the M.C. dial.
Select a source Press SRC/OFF repeatedly.
Change the display information Press DISP repeatedly.
SRC (source)/OFF
Detach button
Display window
M.C. (multi-control) dial
BAND/DIMMER
DISP (display)
* When this unit’s blue/white lead is connected to the vehicles auto-antenna relay control
terminal, the vehicles antenna extends when this unit’s source is turned on. To retract the
antenna, turn the source off.
Display indication
Detach the front panel to prevent theft. Remove any cables and devices
attached to the front panel and turn off the unit before detaching it.
Important
Avoid subjecting the front panel to excessive shock.
Return to the previous display/list Press BAND/DIMMER .
Return to the normal display from the
menu
Press and hold BAND/DIMMER .
Indication Description
Appears when a lower tier of the menu or folder exists.
Appears when the button is pressed.
Appears when the local seek tuning function is set (page 7).
Appears when random/shuffle play is set.
Appears when repeat play is set.
Detaching the front panel
Purpose Operation
Detach Attach
_127075006696_artwork.book Page 3 Monday, July 27, 2015 10:01 AM
4
H:\PDF-OUT\127075006696_KM636UW\020Chapter_EN.fm
MVH-08UB/MVH-08UBG
127075006696
En
Keep the front panel out of direct sunlight and high temperatures.
Always store the detached front panel in a protective case or bag.
When you turn the ignition switch to ON after installation, [SET UP :YES]
appears in the display.
1 Press the M.C. dial.
The setup menu disappears after 30 seconds of no operation. If you prefer
not to set at this time, turn the M.C. dial to select [NO], then press to
confirm.
2 Turn the M.C. dial to select the options, then press to confirm.
To proceed to the next menu option, you need to confirm your selection.
3 [QUIT :YES] appears when all the settings have been made.
To return to the first item of the setup menu, turn the M.C. dial to select
[QUIT :NO], then press to confirm.
4 Press the M.C. dial to confirm the settings.
NOTES
You can cancel the menu setting by pressing SRC/OFF.
Setup menu
Menu Item Description
LANGUAGE Select the language to display the text information from a
compressed audio file.
[ENG]
(English),
[РУС]
(Russian),
[TUR]
(Turkish)
CLOCK SET Set the clock.
FM STEP Select the FM tuning step from 100 kHz or 50 kHz.
[100], [50]
These settings can be made at any time from the SYSTEM settings (page 8) and INITIAL
settings (page 4).
1 Press the M.C. dial to display the main menu.
2 Turn the M.C. dial to select [SYSTEM], then press to confirm.
3 Turn the M.C. dial to select [DEMO OFF], then press to confirm.
4 Turn the M.C. dial to select [YES], then press to confirm.
1 Press and hold SRC/OFF until the unit turns off.
2 Press the M.C. dial to display the main menu.
3 Turn the M.C. dial to select [INITIAL], then press to confirm.
4 Turn the M.C. dial to select an option, then press to confirm.
NOTE
The options vary depending on the unit.
Canceling the demonstration display (DEMO
OFF)
INITIAL settings
Menu Item Description
FM STEP Select the FM tuning step from 100 kHz or 50 kHz.
[100], [50]
_127075006696_artwork.book Page 4 Monday, July 27, 2015 10:01 AM
5
H:\PDF-OUT\127075006696_KM636UW\020Chapter_EN.fm
MVH-08UB/MVH-08UBG
127075006696
En
English
The tuner frequencies on this unit are allocated for use in Western Europe,
Asia, the Middle East, Africa and Oceania. Use in other areas may result in poor
reception. The RDS (radio data system) function only works in areas that
broadcast RDS signals for FM stations.
1 Press SRC/OFF to select [RADIO].
2 Press BAND/DIMMER to select the band from [FM1], [FM2], [FM3],
[MW] or [LW].
SP-P/O MODE Select when there is a full-range speaker connected to
the rear speaker output leads and there is a subwoofer
connected to the RCA output.
[REAR/SUB.W]
[SUB.W/SUB.W] Select when there is a passive subwoofer connected
directly to the rear speaker output leads and there is a
subwoofer connected to the RCA output.
[REAR/REAR] Select when there are full-range speakers connected to
the rear speaker output leads and RCA output. If there is
a full-range speaker connected to the rear speaker
output leads, and the RCA output is not used, you may
select either [REAR/SUB.W] or [REAR/REAR].
DIM SETTING Change the display brightness.
[SYNC CLOCK],
[MANUAL]
SYSTEM RESET Select [YES] to initialize the unit settings. The unit will be
restarted automatically.
(Some of the settings may be retained even after
resetting the unit.)
[YES], [CANCEL]
Radio
Receiving preset stations
Menu Item Description
3 Press a number button (1/ to 6/).
TIP
The / buttons can be also used to select a preset station when [SEEK] is set to
[PCH] in the FUNCTION settings (page 7).
The six strongest stations are stored on the number buttons (1/ to 6/).
1 After selecting the band, press the M.C. dial to display the main menu.
2 Turn the M.C. dial to select [FUNCTION], then press to confirm.
3 Turn the M.C. dial to select [BSM], then press to confirm.
To seek a station manually
1
After selecting the band, press / to select a station.
Press and hold / then release to seek an available station.
Scanning stops when the unit receives a station. To cancel seek tuning,
press / .
NOTE
[SEEK] needs to be set to [MAN] in the FUNCTION settings (page 7).
To store stations manually
1
While receiving the station you want to store, press and hold one of the
number buttons (1/ to 6/ ) until it stops flashing.
Disconnect headphones from the device before connecting it to the unit.
Best stations memory (BSM)
USB/AUX
Playing back
_127075006696_artwork.book Page 5 Monday, July 27, 2015 10:01 AM
6
H:\PDF-OUT\127075006696_KM636UW\020Chapter_EN.fm
MVH-08UB/MVH-08UBG
127075006696
En
USB devices (including Android)
1
Open the USB port cover.
2 Plug in the USB.
NOTE
To automatically switch to [USB] source when a USB device is connected to the unit, set
[USB AUTO] to [ON] in the SYSTEM settings (page 9).
CAUTION
Use an optional Pioneer USB cable (CD-U50E) to connect the USB device as any device
connected directly to the unit will protrude out from the unit, which could be dangerous.
Before removing the device, stop playback.
AOA connections
A device installed with Android OS 5.0 or later can be connected to the unit via
AOA, using the cable supplied with the device.
This function is compatible with devices that have Android OS 5.0 or later
installed and also support Bluetooth SPP (Serial Port Profile) and AOA (Android
Open Accessory) 2.0.
Listening to music on Android
AUX input jack (3.5 mm stereo jack)
USB port
SRC (source)/OFF
M.C. (multi-control) dial
1 Press SRC/OFF to select [ANDROID].
Basic operations
AUX
1
Insert the stereo mini plug into the AUX input jack.
2 Press SRC/OFF to select [AUX] as the source.
NOTE
If [AUX] is set to [OFF] in the SYSTEM settings, [AUX] cannot be selected as a source (page 8).
You can make various adjustments in the FUNCTION settings (page 7).
Note that the following operations do not work for an AUX device. To operate
an AUX device, use the device itself.
Purpose Operation
Select a track Press or .
Fast forward or reverse Press and hold or .
Pause/resume playback Press 4/PAUS E.
Operations
Purpose Operation
Select a folder/album* Press 1/ or 2/.
Select a track/song (chapter) Press or .
Fast forward or reverse Press and hold or .
Search for a file from a list 1 Press to display the list.
2 Turn the M.C. dial to select the
desired file (folder) name or
category, then press to confirm.
3 Turn the M.C. dial to select the
desired file, then press to confirm.
Playback starts.
_127075006696_artwork.book Page 6 Monday, July 27, 2015 10:01 AM
7
H:\PDF-OUT\127 07500669 6_KM636UW\020Chapter_EN.fm
MVH-08UB/MVH-08UBG
127075006696
En
English
* Compressed audio les only
You can adjust various settings in the main menu.
1 Press the M.C. dial to display the main menu.
2 Turn the M.C. dial to select one of the categories below, then press to
con
rm.
FUNCTION settings (page 7)
AUDIO settings (page 7)
SYSTEM settings (page 8)
3 Turn the M.C. dial to select the options, then press to con rm.
The menu items vary according to the source.
View a list of the les in the selected
folder/category*
Press the M.C. dial when a folder/
category is selected.
Play a song in the selected folder/
category*
Press and hold the M.C. dial when a
folder/category is selected.
sserPyalp taepeR 6/ .
Random/shu
play Press 5/ .
Pause/resume playback Press 4/PAUSE.
Settings
FUNCTION settings
Purpose Operation Menu Item Description
BSM
Store the six strongest stations on the
number buttons (1/ to 6/ )
automatically.
LOCAL
FM: [OFF], [LV1], [LV2], [LV3],
[LV4]
MW/LW: [OFF], [LV1], [LV2]
Restrict the tuning station according to the
signal strength.
SEEK
[MAN], [PCH] Assign or buttons to seek the
stations one by one (manual tuning) or
select a station from the preset channels.
AUDIO settings
Menu Item Description
FADER*1
Adjust the front and rear speaker balance.
BALANCE
Adjust the left and right speaker balance.
_127075006696_artwork.book Page 7 Monday, July 27, 2015 10:01 AM
8
H:\PDF-OUT\127075006696_KM636UW\020Chapter_EN.fm
MVH-08UB/MVH-08UBG
127075006696
En
EQ SETTING
[SUPER BASS], [POWERFUL],
[NATURAL], [VOCAL],
[CUSTOM1], [CUSTOM2],
[FLAT]
Select an equalizer band and
level for further customizing.
Equalizer band: [80HZ],
[250HZ], [800HZ], [2.5KHZ],
[8KHZ]
Equalizer level: [+6] to [–6]
Select or customize the equalizer curve.
[CUSTOM1] can be set separately for each
source. However, each of the below
combinations are set to the same setting
automatically.
USB, ANDROID, and APP (Android)
[CUSTOM2] is a shared setting used for all
sources.
You can also switch the equalizer by
pressing repeatedly.
LOUDNESS
[OFF], [LOW], [MID], [HI] Compensate for clear sound at low volume.
SUB.W*2
[NOR], [REV], [OFF] Select the subwoofer phase.
SUB.W CTRL*2*3
Cut-off frequency: [50HZ],
[63HZ], [80HZ], [100HZ],
[125HZ], [160HZ], [200HZ]
Output level: [–24] to [+6]
Slope level: [–12], [–24]
Only frequencies lower than those in the
selected range are output from the
subwoofer.
BASS BOOST
[0] to [+6] Select the bass boost level.
HPF SETTING
Cut-off frequency: [OFF],
[50HZ], [63HZ], [80HZ],
[100HZ], [125HZ], [160HZ],
[200HZ]
Slope level: [–12], [–24]
Only frequencies higher than the high-pass
filter (HPF) cutoff are output from the
speakers.
Menu Item Description
*1 Not available when [SUB.W/SUB.W] is selected in [SP-P/O MODE] in the INITIAL settings
(page 5).
*2 Not available when [REAR/REAR] is selected in [SP-P/O MODE] in the INITIAL settings
(page 5).
*3 Not available when [OFF] is selected in [SUB.W].
You can also access to these menus when the unit is turned off.
SLA
[+4] to [–4] Adjust the volume level for each source
except RADIO.
Each of the below combinations are set to
the same setting automatically.
USB, APP (Android)
SYSTEM settings
Menu Item Description
LANGUAGE
[ENG](English), [РУС]
(Russian), [TUR](Turkish)
Select the language to display the text
information from a compressed audio file.
CLOCK SET
Set the clock (page 4).
12H/24H
[12H], [24H] Select the time notation.
AUX
[ON], [OFF] Set to [ON] when using an auxiliary device
connected to the unit.
Menu Item Description
_127075006696_artwork.book Page 8 Monday, July 27, 2015 10:01 AM
9
H:\PDF-OUT\127075006696_KM636UW\020Chapter_EN.fm
MVH-08UB/MVH-08UBG
127075006696
En
English
USB AUTO
[ON], [OFF] Select [ON] to automatically switch to
[USB] source when a USB device/Android is
connected to the unit.
Select [OFF] when a USB device/Android is
being connected to the unit just for
charging.
Menu Item Description
Important
When installing this unit in a vehicle
without an ACC (accessory) position
on the ignition switch, failure to
connect the red cable to the terminal
that detects operation of the ignition
key may result in battery drain.
Use of this unit in conditions other
than the following could result in fire
or malfunction.
Vehicles with a 12-volt battery and
negative grounding.
Use speakers over 50 W (Maximum
input power) and between 4 Ω to 8
Ω (impedance value).
To prevent a short-circuit,
overheating or malfunction, be sure
to follow the directions below.
Disconnect the negative terminal
of the battery before installation.
Secure the wiring with cable
clamps or adhesive tape. Wrap
adhesive tape around wiring that
comes into contact with metal
parts to protect the wiring.
Place all cables away from moving
parts, such as the shift lever and
seat rails.
Place all cables away from hot
places, such as near the heater
outlet.
Do not connect the yellow cable to
the battery by passing it through
the hole to the engine
compartment.
Cover any disconnected cable
connectors with insulating tape.
Do not shorten any cables.
Never cut the insulation of the
power cable of this unit in order to
share the power with other devices.
The current capacity of the cable is
limited.
Use a fuse of the rating prescribed.
Never wire the negative speaker
cable directly to ground.
Never band together negative
cables of multiple speakers.
When this unit is on, control signals
are sent through the blue/white
cable. Connect this cable to the
system remote control of an external
power amp or the vehicle’s auto-
antenna relay control terminal (max.
300mA 12 V DC). If the vehicle is
equipped with a glass antenna,
connect it to the antenna booster
power supply terminal.
Never connect the blue/white cable
to the power terminal of an external
power amp. Also, never connect it to
the power terminal of the auto
antenna. Doing so may result in
battery drain or a malfunction.
Connections/Installation
Connections
ACC position No ACC position
_127075006696_artwork.book Page 9 Monday, July 27, 2015 10:01 AM
10
H:\PDF-OUT\127075006696_KM636UW\020Chapter_EN.fm
MVH-08UB/MVH-08UBG
127075006696
En
The black cable is ground. Ground
cables for this unit and other
equipment (especially, high-current
products such as power amps) must
be wired separately. If they are not,
an accidental detachment may result
in a fire or malfunction.
This unit
Rear output or subwoofer output
Antenna input
Power cord input
Fuse (10 A)
Power cord
Perform these connections when not
connecting a rear speaker lead to a
subwoofer.
Perform these connections when
using a subwoofer without the
optional amplifier.
To power cord input
Left
Right
Front speaker
Rear speaker
White
White/black
Gray
Gray/black
Green
Green/black
Violet
Violet/black
Black (chassis ground)
Connect to a clean, paint-free
metal location.
Yel low
Connect to the constant 12 V
supply terminal.
Red
Connect to terminal controlled by
the ignition switch (12 V DC).
Blue/white
Connect to the system control
terminal of the power amp or auto-
antenna relay control terminal
(max. 300 mA 12 V DC).
Subwoofer (4 Ω)
When using a subwoofer of 2 Ω, be
sure to connect the subwoofer to
the violet and violet/black leads of
this unit. Do not connect anything
to the green and green/black leads.
Not used.
Subwoofer (4 Ω) × 2
NOTE
Change the initial menu of this unit.
Refer to [SP-P/O MODE] (page 5). The
subwoofer output of this unit is
monaural.
Power amp (sold separately)
Perform these connections when
using the optional amplifier.
System remote control
Connect to blue/white cable.
Power amp (sold separately)
Connect with RCA cables (sold
separately)
To rear output or subwoofer output
Rear speaker or subwoofer
Important
Check all connections and systems
before final installation.
Do not use unauthorized parts as
this may cause malfunctions.
Consult your dealer if installation
requires drilling of holes or other
modifications to the vehicle.
Do not install this unit where:
it may interfere with operation of
the vehicle.
it may cause injury to a passenger
as a result of a sudden stop.
The semiconductor laser will be
damaged if it overheats. Install this
unit away from hot places such as
near the heater outlet.
Optimum
performance is
obtained when the
unit is installed at an
angle of less than 60°.
When installing, to ensure proper
heat dispersal when using this unit,
make sure you leave ample space
behind the rear panel and wrap any
loose cables so they are not blocking
the vents.
Installation
Leave ample
space
5 cm
5 cm
_127075006696_artwork.book Page 10 Monday, July 27, 2015 10:01 AM
11
H:\PDF-OUT\127075006696_KM636UW\020Chapter_EN.fm
MVH-08UB/MVH-08UBG
127075006696
En
English
DIN mount installation
1 Insert the supplied mounting
sleeve into the dashboard.
2 Secure the mounting sleeve by
using a screwdriver to bend the
metal tabs (90°) into place.
Dashboard
Mounting sleeve
Make sure that the unit is
installed securely in place. An
unstable installation may cause
skipping or other malfunctions.
When not using the supplied
mounting sleeve
1 Line up the holes on the
mounting bracket with the holes
on the sides of the unit to attach
the bracket.
2 Screw in one screw on each side to
hold the unit in place.
Tapping screw (5 mm × 9 mm,
not supplied with product)
Mounting bracket
Dashboard or console
Using the included bracket
Check to make sure that the included
bracket matches your particular
model of vehicle and then attach it to
the unit as shown below.
Screw
Bracket
Removing the unit (installed
with the supplied mounting
sleeve)
1 Remove the trim ring.
Trim ring
Notched tab
Releasing the front panel allows
easier access to the trim ring.
When reattaching the trim ring,
point the side with the notched
tab down.
2 Insert the supplied extraction
keys into both sides of the unit
until they click into place.
3 Pull the unit out of the dashboard.
_127075006696_artwork.book Page 11 Monday, July 27, 2015 10:01 AM
12
H:\PDF-OUT\127075006696_KM636UW\020Chapter_EN.fm
MVH-08UB/MVH-08UBG
127075006696
En
The display automatically returns to
the normal display.
No operations have been made for
about 30 seconds.
Perform an operation.
The repeat play range changes
unexpectedly.
Depending on the repeat play
range, the selected range may
change when another folder or
track is being selected or during
fast forwarding/reversing.
Select the repeat play range
again.
A subfolder is not played back.
Subfolders cannot be played when
[FLD] (folder repeat) is selected.
Select another repeat play range.
The sound is intermittent.
You are using a device, such as a
cellular phone, that may cause
audible interference.
Move electrical devices that may
be causing the interference away
from the unit.
Common
AMP ERROR
This unit fails to operate or the
speaker connection is incorrect.
The protective circuit is activated.
Check the speaker connection.
Turn the ignition switch OFF and
back to ON again. If the message
remains, contact your dealer or an
authorized Pioneer Service
Station for assistance.
USB device
NO AUDIO
There are no songs.
Transfer the audio files to the USB
device and connect.
The connected USB device has
security enabled.
Follow the USB device
instructions to disable the
security.
SKIPPED
The connected USB device contains
DRM protected files.
The protected files are skipped.
PROTECT
All the files on the connected USB
device are embedded with DRM.
Replace the USB device.
Additional Information
Troubleshooting Error messages
N/A USB
The connected USB device is not
supported by this unit.
Disconnect your device and
replace it with a compatible USB
device.
CHECK USB
The USB connector or USB cable
has short-circuited.
Check that the USB connector or
USB cable is not caught in
something or damaged.
The connected USB device
consumes more than maximum
allowable current.
Disconnect the USB device and
do not use it. Turn the ignition
switch OFF and back to ACC or
ON. Connect only compliant USB
devices.
ERROR-19
Communication failed.
Perform one of the following
operations, then return to the
USB source.
Turn the ignition switch OFF and
back to ON.
Disconnect the USB device.
Change to a different source.
ERROR-23
USB device was not formatted
properly.
Format the USB device with
FAT12, FAT16 or FAT32.
USB storage device
Connections via USB hubs are not
supported.
Firmly secure the USB storage device
before driving. Do not let the USB
storage device fall onto the floor,
where it may become jammed under
the brake or accelerator pedal.
Depending on the USB storage
device, the following problems may
occur.
–Operations may vary.
The storage device may not be
recognized.
Files may not be played back
properly.
The device may cause audible
interference when you are listening
to the radio.
Only the first 32 characters can be
displayed as a file name (including
the file extension) or a folder name.
The unit may not work properly
depending on the application used
to encode WMA files.
There may be a slight delay at the
start of the playback of audio files
embedded with image data, or audio
files stored on a USB device with
numerous folder hierarchies.
Handling guidelines
Compressed audio
compatibility
_127075006696_artwork.book Page 12 Monday, July 27, 2015 10:01 AM
13
H:\PDF-OUT\127075006696_KM636UW\020Chapter_EN.fm
MVH-08UB/MVH-08UBG
127075006696
En
English
Russian text to be displayed on this
unit should be encoded in one of the
following character sets:
Unicode (UTF-8, UTF-16)
A character set other than Unicode
that is used in a Windows
environment and is set to Russian
in the multi-language setting
CAUTION
Pioneer cannot guarantee
compatibility with all USB mass
storage devices, and assumes no
responsibility for any loss of data on
media players, smartphones, or
other devices while using this
product.
Do not leave discs or a USB storage
device in any place that is subject to
high temperatures.
WMA files
MP3 files
WAV files
USB device
There may be a slight delay when
starting playback of audio files on a
USB storage device with numerous
folder hierarchies.
File extension .wma
Bit rate 48 kbps to 320 kbps
(CBR), 48 kbps to
384 kbps (VBR)
Sampling
frequency
32 kHz, 44.1 kHz, 48
kHz
Windows Media™
Audio Professional,
Lossless, Voice/
DRM Stream/
Stream with video
Not compatible
File extension .mp3
Bit rate 8 kbps to 320 kbps
(CBR), VBR
Sampling
frequency
16 kHz to 48 kHz (32
kHz, 44.1 kHz, 48
kHz for emphasis)
Compatible ID3 tag
version
2.2, 2.3, 2.4
M3u playlist Not compatible
MP3i (MP3
interactive), mp3
PRO
Not compatible
File extension .wav
Quantization bits 8 and 16 (LPCM), 4
(MSADPCM)
Sampling
frequency
16 kHz to 48 kHz
(LPCM), 22.05 kHz
and 44.1 kHz (MS
ADPCM)
Playable folder
hierarchy
Up to eight tiers (A
practical hierarchy
is less than two
tiers.)
Playable folders Up to 500
Playable files Up to 15 000
Playback of
copyright-
protected files
Not compatible
The user cannot assign folder
numbers and specify playback
sequences with this unit. Sequence of
audio file depends on the connected
device.
Note that the hidden files in a USB
device cannot be played back.
Example of a hierarchy
WMA
Windows Media is either a registered
trademark or trademark of Microsoft
Corporation in the United States and/
or other countries.
Partitioned USB
device
Only the first
partition can be
played.
Sequence of audio files
Folder
Compressed
audio file
to : Playback sequence
01 to 05: Folder number
Russian character
chart
Copyright and
trademark
_127075006696_artwork.book Page 13 Monday, July 27, 2015 10:01 AM
14
H:\PDF-OUT\127075006696_KM636UW\020Chapter_EN.fm
MVH-08UB/MVH-08UBG
127075006696
En
This product includes technology
owned by Microsoft Corporation and
cannot be used or distributed without
a license from Microsoft Licensing, Inc.
Android™
Android is a trademark of Google Inc.
General
Power source: 14.4 V DC (10.8 V to 15.1
V allowable)
Grounding system: Negative type
Maximum current consumption: 10.0
A
Dimensions (W × H × D):
DIN
Chassis: 178 mm × 50 mm × 97
mm
Nose: 188 mm × 58 mm × 17 mm
D
Chassis: 178 mm × 50 mm × 97
mm
Nose: 170 mm × 46 mm × 17 mm
Weight: 0.5 kg
Audio
Maximum power output:
50 W × 4 ch/4 Ω (for no
subwoofer)
50 W × 2 ch/4 Ω + 70 W × 1 ch/2
Ω (for subwoofer)
Continuous power output:
22 W × 4 (50 Hz to 15 000 Hz, 5 %
THD, 4 Ω load, both channels
driven)
Load impedance: 4 Ω (4 Ω to 8 Ω
allowable)
Preout maximum output level: 2.0 V
Loudness contour: +10 dB (100 Hz),
+6.5 dB (10 kHz) (volume: –30 dB)
Equalizer (5-Band Graphic Equalizer):
Frequency: 80 Hz/250 Hz/800 Hz/
2.5 kHz/8 kHz
Equalization range: ±12 dB (2 dB
step)
Subwoofer (mono):
Frequency: 50 Hz/63 Hz/80 Hz/
100 Hz/125 Hz/160 Hz/200 Hz
Slope: –12 dB/oct, –24 dB/oct
Gain: +6 dB to –24 dB
Phase: Normal/Reverse
USB
USB standard specification: USB 2.0
full speed
Maximum current supply: 500 mA
USB Protocol:
MSC (Mass Storage Class)
AOA (Android Open Accessory)
2.0
File system: FAT12, FAT16, FAT32
MP3 decoding format: MPEG-1 & 2
Audio Layer 3
WMA decoding format: Ver. 7, 7.1, 8, 9
(2 ch audio) (Windows Media
Player)
WAV signal format: Linear PCM & MS
ADPCM (Non-compressed)
FM tuner
Frequency range: 87.5 MHz to 108.0
MHz
Usable sensitivity: 11 dBf (1.0 μV/75 Ω,
mono, S/N: 30 dB)
Signal-to-noise ratio: 72 dB (IEC-A
network)
Specifications
MW tuner
Frequency range: 531 kHz to 1 602 kHz
Usable sensitivity: 25 μV (S/N: 20 dB)
Signal-to-noise ratio: 62 dB (IEC-A
network)
LW tuner
Frequency range: 153 kHz to 281 kHz
Usable sensitivity: 28 μV (S/N: 20 dB)
Signal-to-noise ratio: 62 dB (IEC-A
network)
NOTE
Specifications and the design are
subject to modifications without
notice.
_127075006696_artwork.book Page 14 Monday, July 27, 2015 10:01 AM
15
H:\PDF-OUT\127075006696_KM636UW\020Chapter_EN.fm
MVH-08UB/MVH-08UBG
127075006696
En
English
_127075006696_artwork.book Page 15 Monday, July 27, 2015 10:01 AM
2
H:\PDF-OUT\127075006696_KM636UW\030Chapter_RU.fm
MVH-08UB/MVH-08UBG
127075006696
Ru
Перед началом эксплуатации .............................................. 2
Начало работы.......................................................................... 3
Радио ........................................................................................... 5
USB/AUX ...................................................................................... 6
Настройки .................................................................................. 8
Настройки FUNCTION ............................................................ 8
Настройки AUDIO.................................................................... 8
Настройки SYSTEM ................................................................. 9
Подключения/Установка ..................................................... 10
Дополнительная информация........................................... 13
О данном руководстве:
В следующих инструкциях USB-накопитель и аудиопроигрыватель USB
называются “USB-устройство”.
Содержание
Благодарим Вас за покупку этого изделия компании PIONEER
Для обеспечения правильности эксплуатации внимательно прочитайте данное
руководство перед началом использования изделия. Особенно важно, чтобы Вы
прочли и соблюдали инструкции, помеченные в данном руководстве заголовками
ПРЕДУПРЕЖДЕНИЕ и ВНИМАНИЕ. Держите данное руководство под рукой для
обращения к нему в будущем.
Частные лица в странах Евросоюза, Швейцарии и Норвегии могут бесплатно
возвращать использованные электронные изделия в специализированные пункты
приема или в магазин (при покупке аналогичного нового устройства).
Если Ваша страна не указана в приведенном выше перечне, обращайтесь в органы
местного управления за инструкциями по правильной утилизации продукта.
Тем самым Вы обеспечите утилизацию Вашего изделия с соблюдением обязательных
процедур по обработке, утилизации и вторичной переработке и, таким образом,
предотвратите потенциальное негативное воздействие на окружающую среду и
здоровье людей.
Дату изготовления оборудования можно определить по серийному номеру, который
содержит информацию о месяце и годе производства.
Перед началом эксплуатации
Если вы желаете утилизировать данное изделие, не выбрасывайте его вместе с
обычным бытовым мусором. Существует отдельная система сбора использованных
электронных изделий в соответствии с законодательством, которая предполагает
соответствующее обращение, возврат и переработку.
_127075006696_artwork.book Page 2 Monday, July 27, 2015 10:01 AM
3
H:\PDF-OUT\127075006696_KM636UW\030Chapter_RU.fm
MVH-08UB/MVH-08UBG
127075006696
Ru
Русский
ПРЕДУПРЕЖДЕНИЕ
Не пытайтесь самостоятельно производить установку или ремонт изделия.
Установка или ремонт изделия лицами, не обладающими специальными
навыками и опытом работы с электронным оборудованием и
автомобильными аксессуарами, могут создать опасность поражения
электрическим током или иных инцидентов.
Ни в коем случае не пытайтесь управлять устройством во время движения. Прежде
чем использовать органы управления устройством, необходимо съехать с дороги и
припарковать автомобиль в безопасном месте.
ВНИМАНИЕ
Не допускайте попадания жидкости на устройство. Это может повлечь поражение
электрическим током. Кроме того, попадание жидкости в устройство может стать
причиной его выхода из строя, перегрева и появления дыма.
Всегда сохраняйте уровень громкости достаточно низким, чтобы были слышны звуки
извне.
При возникновении проблем
При неполадках в работе этого изделия свяжитесь с торговым представителем
компании-производителя или с ближайшим сервисным пунктом PIONEER.
MVH-08UB/08UBG
Часто используемые операции
Начало работы
Основные операции
Назначение Операция
Включение питания* Нажмите SRC/OFF для включения
питания.
Нажмите и удерживайте SRC/OFF
для выключения питания.
Настройка громкости Поверните регулятор M.C..
Выбор источника Несколько раз нажмите SRC/OFF.
Изменение информации на дисплее Несколько раз нажмите DISP.
Возврат к предыдущему экрану/
списку
Нажмите BAND/DIMMER .
Возврат к обычному дисплею из
меню
Нажмите и удерживайте BAND/
DIMMER .
SRC (источник)/OFF
Кнопка отсоединения
Окно дисплея
Регулятор M.C. (многозадачное управление)
BAND/DIMMER
DISP (дисплей)
_127075006696_artwork.book Page 3 Monday, July 27, 2015 10:01 AM
4
H:\PDF-OUT\127075006696_KM636UW\030Chapter_RU.fm
MVH-08UB/MVH-08UBG
127075006696
Ru
* Когда голубой/белый провод этого устройства подключен к терминалу релейного
управления автоматической антенны, антенна на автомобиле выдвигается при
включении источника сигнала этого устройства. Чтобы втянуть антенну, выключите
источник сигнала.
Индикация на дисплее
Снимите переднюю панель во избежание кражи. Перед снятием панели
отсоедините кабели и устройства, подключенные к передней панели, и
отключите устройство.
Важно
Оберегайте переднюю панель от сильных ударов.
Не подвергайте переднюю панель воздействию прямых солнечных лучей и высоких
температур.
Индикаци
я
Описание
Отображается при наличии нижнего уровня меню или папки.
Отображается при нажатии кнопки .
Отображается при настройке функции поиска локальных
радиостанций (стр. 8).
Отображается при настройке произвольного/перемешанного
воспроизведения.
Отображается при установке повтора воспроизведения.
Снятие передней панели
Снятие Установка
Всегда храните снятую панель в защитном чехле или сумке.
После установки устройства поверните ключ зажигания в положение ON;
на дисплее отобразится [SET UP :YES].
1 Нажмите регулятор M.C..
Если в течение 30 секунд устройство не используется, установочное
меню не будет выводиться. Если вы хотите выполнить настройку
позже, поверните M.C., чтобы выбрать [NO], и нажмите для
подтверждения.
2 Поверните M.C. для выбора параметров, затем нажмите для
подтверждения.
Для перехода к следующему пункту меню необходимо подтвердить
выбор.
3 [QUIT :YES] отображается после выполнения всех настроек.
Для возврата к первому элементу установочного меню поверните
M.C. для выбора [QUIT :NO], затем нажмите для подтверждения.
4 Нажмите M.C. для подтверждения настроек.
Установочное меню
Элемент меню Описание
LANGUAGE Выбор языка для отображения текстовой информации с
сжатого аудиофайла.
[ENG]
(Английский
), [РУС]
(Русский),
[TUR]
(Турецкий)
CLOCK SET Настройка часов.
FM STEP Выбор шага настройки в FM-диапазоне (100 кГц или 50
кГц).
[100], [50]
_127075006696_artwork.book Page 4 Monday, July 27, 2015 10:01 AM
5
H:\PDF-OUT\127075006696_KM636UW\030Chapter_RU.fm
MVH-08UB/MVH-08UBG
127075006696
Ru
Русский
ПРИМЕЧАНИЯ
Вы можете отменить настройку параметра меню, нажав кнопку SRC/OFF.
Настроить параметры меню можно в настройках SYSTEM (стр. 9) и настройках INITIAL
(стр. 5).
1 Нажмите M.C. для отображения главного меню.
2 Поверните M.C. для выбора [SYSTEM], затем нажмите для
подтверждения.
3 Поверните M.C. для выбора [DEMO OFF], затем нажмите для
подтверждения.
4 Поверните M.C. для выбора [YES], затем нажмите для
подтверждения.
1 Нажмите и удерживайте SRC/OFF, пока устройство не отключится.
2 Нажмите M.C. для отображения главного меню.
3 Поверните M.C. для выбора [INITIAL], затем нажмите для
подтверждения.
4 Поверните M.C. для выбора параметра, затем нажмите для
подтверждения.
ПРИМЕЧАНИЕ
Параметры могут отличаться в зависимости от устройства.
Отмена демонстрационного дисплея
(DEMO OFF)
Настройки INITIAL
Элемент меню Описание
FM STEP Выбор шага настройки в FM-диапазоне (100 кГц или
50 кГц).
[100], [50]
Радиочастоты данного устройства предназначены для использования в
Западной Европе, Азии, Среднем Востоке, Африке и Океании. В других
областях прием может быть неудовлетворительным. Функция RDS
(система радиоданных) работает только в областях, где выполняется
вещание сигналов RDS для FM-станций.
SP-P/O MODE Используется, когда полночастотный динамик
подключен к проводам вывода заднего динамика, а
сабвуфер подключен к выводу RCA.
[REAR/SUB.W]
[SUB.W/SUB.W] Используется, когда пассивный сабвуфер подключен
непосредственно к проводам вывода заднего
динамика, а сабвуфер подключен к выводу RCA.
[REAR/REAR] Используется, когда полночастотный динамик
подключен к проводам вывода заднего динамика
выводу RCA Если полночастотный динамик
подключен к проводам вывода заднего динамика и
вывод RCA не используется, выберите [REAR/SUB.W]
или [REAR/REAR].
DIM SETTING Изменение яркости дисплея.
[SYNC CLOCK],
[MANUAL]
SYSTEM RESET Выберите [YES] для инициализации настроек
устройства. Устройство будет перезагружено
автоматически.
(Некоторые настройки будут сохранены даже после
сброса параметров устройства.)
[YES], [CANCEL]
Радио
Элемент меню Описание
_127075006696_artwork.book Page 5 Monday, July 27, 2015 10:01 AM
6
H:\PDF-OUT\127075006696_KM636UW\030Chapter_RU.fm
MVH-08UB/MVH-08UBG
127075006696
Ru
1 Нажмите SRC/OFF для выбора [RADIO].
2 Нажмите BAND/DIMMER для выбора полосы [FM1], [FM2], [FM3],
[MW] или [LW].
3 Нажмите числовую кнопку (от 1/ до 6/).
СОВЕТ
Кнопки / можно также использовать для выбора предварительно
установленной станции, если для параметра [SEEK] установлено значение [PCH] в
настройках FUNCTION (стр. 8).
За каждой числовой кнопкой сохранена одна из шести радиостанций с
наилучшим качеством приема (с 1/ по 6/).
1 После выбора полосы нажмите регулятор M.C. для отображения
главного меню.
2 Поверните M.C. для выбора [FUNCTION], затем нажмите для
подтверждения.
3 Поверните M.C. для выбора [BSM], затем нажмите для
подтверждения.
Поиск станции вручную
1
После выбора полосы нажмите / для выбора станции.
Нажмите и удерживайте / , затем отпустите для поиска
доступной станции. Поиск остановится, когда устройство выполнит
прием станции. Для отмены поиска нажмите / .
Прием предварительно установленных
станций
Запоминание лучших станций (BSM)
ПРИМЕЧАНИЕ
Для параметра [SEEK] необходимо установить значение [MAN] в настройках FUNCTION
(стр. 8).
Сохранение станций вручную
1
Во время приема станции, которую требуется сохранить, нажмите и
удерживайте одну из числовых кнопок (с 1/ по 6/), пока
мигание не прекратится.
Отключите от устройства наушники перед подключением к
оборудованию.
Устройства USB (включая Android)
1
Откройте крышку порта USB.
2 Подключите USB.
USB/AUX
Воспроизведение
Вход AUX (стереоразъем 3,5 мм)
USB-порт
SRC (источник)/OFF
Регулятор M.C.
(многозадачное управление)
_127075006696_artwork.book Page 6 Monday, July 27, 2015 10:01 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Pioneer MVH-08UBG Руководство пользователя

Категория
Мультимедиа-приемники для автомобилей
Тип
Руководство пользователя
Это руководство также подходит для

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ