Sparky Group BUR 15E Руководство пользователя

Бренд: Sparky Group

Модель: BUR 15E

Категория: Электроинструменты

Тип: Руководство пользователя

Это руководство также подходит для

Battery Charger BUR 15E

Contents

I - Introduction ..................................................................................................................................... 1

II - Technical speciﬁcations .................................................................................................................

III - General safety instructions for electric power tools .................................................................... 3

IV - Additional safety rules for drills .......................................................................................................

V - Additional instructions for work with the charger .........................................................................

VI - Additional instructions for work with the battery pack .................................................................. 5

VII - Know your product .................................................................................................................... A/6

VIII - Operation ........................................................................................................................................ 6

IX - Maintenance .................................................................................................................................. 8

X - Warranty ......................................................................................................................................... 9

I - Introduction

Your new SPARKY power tool will more than satisfy your expectations. It has been manufactured under

stringent SPARKY Quality Standards to meet superior performance criteria. You will ﬁnd your new tool

easy and safe to operate, and, with proper care, it will give you many years of dependable service.

CAUTION!

Carefully read through this entire Instruction Manual before using your new SPARKY Power Tool. Take

special care to heed the Cautions and Warnings. Your SPARKY power tool has many features that will

make your job faster and easier. Safety, performance, and dependability have been given top priority in

the development of this tool, making it easy to maintain and operate.

Do not dispose of electrical products together with household waste!

Waste electrical products should not be disposed of with household waste. Please recycle where

facilities exist. Check with your local authority or retailer for recycling advice.

ENVIRONMENTAL PROTECTION

The machine, accessories and packaging should be sorted for environmental-friendly recycling.

The plastic components are labelled for categorised recycling.

UNPACKING

Due to modern mass production techniques, it is unlikely that your power tool is faulty or that a part is

missing. If you ﬁnd anything wrong, do not operate the tool until the parts have been replaced or the fault

has been rectiﬁed. Failure to do so could result in serious personal injury.

ASSEMBLY

The SPARKY Cordless Impact Drill / Driver BUR 15E (BUR 18E) is packed fully assembled.

BUR 15E • BUR 18E – Instruction Manual

pages-BUR15-18-[13mm].indd 1 22.3.2006 ã. 09:05:32

BUR 15E • BUR 18EEN

DESCRIPTION OF SYMBOLS

The rating plate on your tool may show symbols. These represent important information about the product

or instructions on its use.

Wear hearing protection.

Wear eye protection.

Wear respiratory protection.

Double insulated for

additional protection.

Conforms to relevant European

safety standards.

pages-BUR15-18-[13mm].indd 2 22.3.2006 ã. 09:05:33

Instruction Manual EN

III - Safety instructions

WARNING. Read and understand all instructions.

Failure to follow all instructions listed below may

result in electric shock, ﬁre and/or serious injury.

The term “power tool” in all of the warnings below

refers to your mains-operated (corded) power tool

or battery-operated (cordless) power tool.

Save these instructions!

WORK AREA

▪ Keep work area clean and well lit. Cluttered and

dark areas invite accidents.

▪ Do not operate power tools in explosive atmos

pheres, such as in the presence of ﬂamma-

ble liquids, gases, or dust. Power tools create

sparks which may ignite the dust or fumes.

▪ Keep children and bystanders away while oper-

ating a power tool. Distractions can cause you

to lose control.

ELECTRICAL SAFETY

▪ Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁed plugs and matching outlets

will reduce risk of electric shock.

▪ Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of elec-

tric shock if your body is earthed or grounded.

▪ Do not expose power tools to rain or wet condi

tions. Water entering a power tool will increase

the risk of electric shock.

▪ Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords in

crease the risk of electric shock.

▪ When operating a power tool outdoors, use an

outdoor extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

PERSONAL SAFETY

▪ Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol, or medi

cation. A moment of inattention while operating

power tools may result in serious personal in

jury.

▪ Use safety equipment. Always wear eye protec-

tion. Safety equipment such as a dust mask,

non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will

reduce personal injuries.

▪ Avoid accidental starting. Ensure the switch is

in the off-position before plugging in. Carrying

power tools with your finger on the switch or

plugging in power tools that have the switch on

invites accidents.

▪ Remove any adjusting key or wrench before

turning the tool on. A wrench or a key that is left

attached to a rotating part of the power tool may

result in personal injury.

▪ Do not overreach. Keep proper footing and bal

ance at all times. This enables better control of

the power tool in unexpected situations.

▪ Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

▪ If devices are provided for the connection of

dust extraction and collection facilities ensure

that these are connected and properly used.

Use of these devices can reduce dust related

hazards.

II - Technical speciﬁcations

BUR 15E BUR 18E

▪ Nominal battery charge: 14.4 V 18 V

▪ Charger: 230–240V ~ 50Hz 230–240V ~ 50Hz

▪ Batteries: 2 x 1.5 Ah 2 x 1.5 Ah

▪ Charging time: 1.5 Hours 1.5 Hours

▪ Drill no load speed: 0–350, 0–1250 min

-1

0–350, 0–1250 min

-1

▪ Torque settings: 20 Positions 20 Positions

▪ Drill chuck capacity: 13 mm Keyless 13 mm Keyless

▪ Max drilling capacity in

steel / wood / concrete: 10 / 28 / 10 mm 13 / 28 / 13 mm

▪ Hammer impact frequency: 0–5600, 0–20.000 min

-1

0–5600, 0–20.000 min

-1

▪ Weight: 2.1 kg 2.1 kg

pages-BUR15-18-[13mm].indd 3 22.3.2006 ã. 09:05:33

BUR 15E • BUR 18EEN

POWER TOOL USE AND CARE

▪ Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

▪ Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

▪ Disconnect the plug from the power source be-

fore making any adjustments, changing acces

sories, or storing power tools. Such preventive

safety measures reduce the risk of starting the

power tool accidentally.

▪ Store idle power tools out of the reach of chil

dren and do not allow persons unfamiliar with

the power tool or these instructions to operate

the power tool. Power tools are dangerous in

the hands of untrained users.

▪ Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

▪ Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

▪ Use the power tool, accessories and tool bits

etc., in accordance with these instructions and

in the manner intended for the particular type

of power tool, taking into account the working

conditions and the work to be performed. Use

of the power tool for operations different from

intended could result in a hazardous situation.

SERVICE

▪ Have your power tool serviced by a qualified

repair personnel using only identical replace

ment parts. This will ensure that the safety of

the power tool is maintained.

IV - Additional safety rules

for drills

Wear ear protectors with impact drills. Expo-

sure to noise can cause hearing loss.

Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

▪ If possible, always use clamps or a vice to hold

your work.

▪ Always switch off before you put the drill down.

▪ Ensure that the lighting is adequate.

▪ Do not put pressure on the drill, such that it

slows the motor down. Allow the drill bit to cut

without pressure. You will get better results and

you will be taking better care of your tool.

▪ Keep the area free of tripping hazards.

▪ Do not let anyone under 18 years operate this

tool.

▪ Only use accessory bits in good condition.

▪ Before drilling, check that there is sufficient

clearance for the drill bit under the workpiece.

▪ Do not touch the bit after operation. It will be

very hot.

▪ Keep your hands away from under the work

piece.

▪ Never use your hands to remove sawdust, chips

or waste close by the bit.

▪ Rags, cloths, cord, string and the like should

never be left around the work area.

▪ Support the work properly.

▪ If you are interrupted when operating the drill,

complete the process and switch off before

looking up.

▪ Periodically check that all nuts, bolts and other

fixings are properly tightened.

▪ When using the drill, use safety equipment in

cluding safety glasses or shield, ear defenders,

and protective clothing including safety gloves.

Wear a dust mask if the drilling operation cre

ates dust.

If in doubt, do not plug in the tool. Using a power

source with a voltage less than the nameplate rat

ing is harmful to the motor.

The tool must be used only for its prescribed pur

pose. Any use other than those mentioned in this

Manual will be considered a case of misuse. The

user and not the manufacturer shall be liable for

any damage or injury resulting from such cases

of misuse.

To use this tool properly, you must observe the

safety regulations, the assembly instructions and

the operating instructions to be found in this Man

ual. All persons who use and service the machine

have to be acquainted with this Manual and must

be informed about its potential hazards.

Children and frail people must not use this tool.

Children should be supervised at all times if they

are in the area in which the tool is being used. It

is also imperative that you observe the accident

prevention regulations in force in your area. The

same applies for general rules of occupational

health and safety.

The manufacturer shall not be liable for any

changes made to the tool nor for any damage re

pages-BUR15-18-[13mm].indd 4 22.3.2006 ã. 09:05:33

Instruction Manual EN

sulting from such changes.

Even when the tool is used as prescribed it is not

possible to eliminate all residual risk factors. The

following hazards may arise in connection with the

tool’s construction and design:

▪ Damage to the lungs if an effective dust mask is

not worn.

▪ Damage to hearing if effective ear defenders

are not worn.

V - Additional instructions

for work with the

charger

▪ Before using the charger, read all the instruc-

tions and cautionary markings on the charger

and battery pack as well as the instructions on

using the battery pack.

▪ Only charge your batteries indoors as the

charger is designed for indoor use only.

CAUTION! If the battery pack is cracked or dam

aged in any other way, do not insert it in the charg

er. There is a danger of electric shock or electro

cution.

WARNING. Do not allow any liquid to come into

contact with the charger. There is a danger of

electric shock.

▪ To allow the battery pack to cool down after

charging, do not place it in a hot environment

such as a metal shed or open trailer left in the

sun.

▪ The charger is not intended for any use other

than charging the exact type of rechargeable

battery pack as supplied with the charger.Any

other use may result in the risk of fire, electric

shock or electrocution.

▪ The charger and battery packs supplied with it

are specifically designed to work together. Do

not attempt to charge the battery pack with any

other charger than the one supplied.

▪ Do not place any object on top of the charger

as it could cause overheating. Do not place the

charger near any heat source.

▪ Do not pull on the lead of the charger to discon

nect it from the power source.

▪ Make sure that the charger cable is positioned

where it will not be stepped on, tripped over or

otherwise subjected to damage or stress.

▪ Do not use an extension cord unless it is abso-

lutely necessary. The use of an improper exten-

sion cord could cause the risk of fire, electric

shock or electrocution.

▪ Do not use the charger if it has been subjected

to a heavy knock, dropped or otherwise dam

aged in any way. Take the charger to an author

ised service centre for a check or repair.

▪ Do not disassemble the charger. Take it to an

authorised service centre when service or re-

pair is required. Incorrect re-assembly may re

sult in the risk of fire, electric shock or electrocu

tion.

▪ To reduce the risk of an electric shock, unplug

the charger from the power supply before at-

tempting to clean it. Removing the battery alone

does not reduce the risk.

▪ Never attempt to connect two chargers togeth

er.

▪ Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) such as alongside sheds

or metal structures in the summer.

▪ The charger is designed for use from a standard

household electrical supply (230–240 volts).

Do not attempt to connect the charger to a sup-

ply with a different supply.

▪ If you wish to charge a second battery pack,

unplug the charger from the mains supply and

leave it for at least 15 minutes. After this time

you can charge a second battery pack.

VI - Additional instructions

for work with the

battery pack

▪ The battery pack for this tool has been shipped

in a low charge condition. You should charge

the battery pack fully before use.

▪ To ensure the longest battery life and best bat-

tery performance, always charge the battery

when the air temperature is between 18–24°C.

Do not charge the battery pack when the tem-

perature is below 0°C, or above 40°C. This is

important. Failure to observe this safety rule

could cause serious damage to the battery

pack.

▪ Do not incinerate the battery pack even if it is

seriously damaged or can no longer hold a

charge. The battery pack can explode in a fire.

▪ Never attempt to open the battery pack for any

reason. If the plastic housing of the battery pack

breaks open or cracks, immediately discontinue

its use and do not recharge it.

▪ The battery pack utilizes nickel-cadmium cells.

Cadmium is considered to be a toxic material.

Use an environmentally safe disposal unit at a

municipal waste disposal centre to dispose of a

damaged or worn out battery.

pages-BUR15-18-[13mm].indd 5 22.3.2006 ã. 09:05:34

BUR 15E • BUR 18EEN

FITTING AND REMOVING THE

BATTERY PACK

To remove the battery pack from the drill ﬁrmly

press the battery release tabs (7) at either side of

the battery pack, and slide the battery backward

out of the tool.

Prior to inserting the battery pack ensure the

switch is in OFF position.

To install the battery pack, align rails, on the tool

with the tabs on the battery pack and slide the bat

tery pack on to the drill. Ensure the battery pack

is sitting straight on the foot and correctly enter-

ing the runners. The battery should slide fully on

to the drill foot until the battery pack “clicks” into

position.

BATTERY CHARGING

NOTE. The battery will be fully charged after

1.5 hours, remove it from the charger after this

time.

1. Align and slide the battery pack (8) onto the

charger (9) until the battery pack latches “click”

into position. Check that there is a firm con

nection between the battery and the charger

groove.

2. Plug in the charger to the wall outlet. The red

LED will be lit during the charging.

3. The battery charging time is approximately

1.5 hours. The red LED goes out when the

charging cycle is complete and the green light

goes on. Unplug the charger power cable from

the mains and then remove the battery from the

charger.

TO OBTAIN THE BEST LIFE FOR

THE BATTERY

Never allow the drill to come to a complete stand

still before recharging. The battery should be

placed on charge whenever the battery is notice-

ably running down or the drill no longer performs

a task it previously performed.

Avoid conducting short charges. Make sure that

the battery is fully charged every time by allowing

the charger to complete its full charging cycle.

Avoid allowing lose items like screws or nails etc.

to be stored with battery packs as these or similar

items can short battery packs and cause a ﬁre or

explosion.

Always unplug the charger when not in use and

store in a dry secure place.

Avoid charging or storing your battery in tempera

tures below 0º C and above 40º C.

BATTERY INDICATOR

To activate the battery indicator feature ﬁrst pull

the trigger switch (3) then press the battery indica

tor button (10), this will display the level of charge

remaining in the battery. There are 3 levels of

charge low, medium and high. When the battery

indicator is showing only 1 LED (low) the battery

should be removed and put on the charger.

VII - Know your product

This drill is mainly used for drilling in wood or metal

sheet and screwdriving. Use the tool and acces

sories only for intended applications. All other ap

plications are expressly ruled out.

1. Keyless chuck

2. Torque adjustment/hammer selection collar

3. Trigger with variable speed control

4. Forward/reverse switch

5. Side handle

6. Side handle clamp knob

7. Battery pack release tabs

8. Rechargeable battery pack

9. Quick charger

10. Battery indicator button

11. LED Lights

12. LED Light switch

13. 2 Speed gear selector

VIII - Operation

LED WORK AREA LIGHT

The drill has 3 LED lights (11) to illuminate the work

area and improve vision when drilling in areas with

insufﬁcient light.

To turn the LED lights on and off depress the LED

light switch (12).

USING THE DRILL

Use the forward/reverse switch (4) to select the

direction of rotation, then pull the trigger (3).

This trigger switch is an electronic variable speed

control which enables the user to vary the speed

continuously. The speed varies according to how

far the trigger switch is depressed, the further it is

depressed the faster the chuck will rotate and the

lighter it is depressed, the slower it will rotate.

To stop the drill, release the trigger switch.

NOTE. You can only change the direction of rota

pages-BUR15-18-[13mm].indd 6 22.3.2006 ã. 09:05:34

Instruction Manual EN

tion of the drill using the forward/reverse switch

when the trigger is NOT depressed.

FORWARD / REVERSE SWITCH

This switch (4) will allow you to change the direc-

tion of the motor while the trigger switch is not de

pressed.

Drilling uses the forward mode. The reverse mode

is intended for the removal of screws.

DRILLING POSITIONS

This symbol indicates the “DRILLING

MODE”. Used for all normal drilling (Wood,

Aluminium, and Steel) in this mode the

clutch is deactivated.

This symbol indicates the “HAMMER

MODE”. This mode will activate hammer

action, whilst drilling. For best results in

hammer mode, set the gear selector to

high gear.

TORQUE ADJUSTMENT / HAMMER

SELECTION COLLAR

By rotating the torque adjustment / hammer selec-

tion collar (2) behind the chuck, it is possible to

adjust the torque to each of 20 settings, or select

hammer action or the drill setting.

The range of 20 torque settings allows better con

trol when using the drill as a screwdriver as it pre

vents over-tightening of the screws.

The symbols circling the collar are used to indi

cate the level of torque. The larger the symbol

on the collar, the higher torque and the larger the

fastener which can be driven. To select any of

the symbols, rotate the collar (2) until the desired

symbol aligns with the arrow head indicator on the

housing.

2 SPEED GEARBOX

The 2 Speed Gearbox allows you to select a gear

with the optimum speed and torque to suit the ap

plication.

NOTE. When changing the gear selector ensure

the drill is not operating.

1. To select the LOW gear (low speed, high torque

setting), push the gear selector (13) forward,

towards the chuck. The word LOW will be dis

played.

2. To select the HIGH gear (high speed, low torque

setting), push the gear selector (13) back, away

from the chuck. The word HIGH will be dis

played.

INSERTING AND REMOVING BITS

The drill is ﬁttedwithauto spindlelockwhichmeans

if you try and rotate the chuck by hand the spindle

of the drill will automatically lock. This means you

only need to grasp the chuck and rotate the chuck

housing to remove or ﬁt accessories.

This drill has a keyless chuck, hence a chuck key

is not needed to secure a bit in the drill. Always set

the forward/reverse switch (4) to the locked ‘OFF’

position when installing and removing bits. It is

also recommended to remove the battery pack to

avoid unintentional starting.

1. Open the chuck jaws by firmly holding the

chuck housing and rotating the housing in an

anti-clockwise direction. Open the jaws suffi

ciently so as to fit the desired accessory.

2. Ensure the accessory is fully inserted, so that

the jaws of the chuck grip onto the flat section

of the accessory.

3. To firmly clamp the accessory in the chuck,

grasp the chuck housing and rotate the chuck

housing in a clockwise direction. Ensure the bit

is retained firmly or damage to the chuck jaws

can result.

4. To remove the accessory, open the chuck jaws

by firmly holding the chuck housing and rotat-

ing the housing in an anti clockwise direction.

Open the jaws sufficiently so as to remove the

specific accessory.

ADJUSTABLE SIDE HANDLE

1. Turn the side handle clamp knob (6) anti-clock-

wise to loosen the collar fully and slip it over the

chuck (1) onto the drill.

2. Adjust the position of the side handle (5) to

suit the application and tighten the side handle

clamp knob (6) to secure it in place.

DRILLING

Drilling metals

▪ For maximum performance, use high speed

steel bits for metal or steel drilling.

▪ Ensure that the torque adjustment / hammer se

lection collar (2) is in normal drilling mode.

▪ Begin drilling at a very low speed to prevent the

bit from slipping off the starting point.

▪ Always clamp sheet metal.

▪ Support thin metal with a block of wood to avoid

distorting it.

▪ Use a punch to mark the centre of the hole.

▪ Use a suitable lubricant for the material you are

working on.

pages-BUR15-18-[13mm].indd 7 22.3.2006 ã. 09:05:35

BUR 15E • BUR 18EEN

Use: For:

Oil Steel

Turpentine or parafﬁn Aluminium

Do not lubricate Brass, copper or cast iron

Drilling plastics and plastic coated chipboard

▪ Use high speed drill bits

▪ See drilling wood below

Drilling masonry

▪ For maximum performance use carbide-tipped

masonry impact bits when drilling holes in brick,

tile, concrete etc.

▪ Turn the mode selector to hammer mode, then

rotate the torque collar to the drill position.

▪ Apply light pressure and medium speed for best

results in brick.

▪ Apply additional pressure and high speed for

hard materials such as concrete.

▪ When drilling holes in tile, practice on a scrap

piece to determine the best speed and pres

sure.

Drilling wood

▪ For maximum performance, use high speed

steel bits for wood drilling.

▪ Ensure that the mode selector is in normal drill

ing mode.

▪ Begin drilling at a very low speed to prevent the

bit from slipping off the starting point. Increase

the speed as the drill bites into the material.

▪ When drilling through holes, place a block of

wood behind the work piece to prevent rag

ged or splintered edges on the back side of the

hole.

WARNING. Never attempt to lock the trigger

switch in the on position, do not lock the trigger

on jobs where your hammer drill may need to be

stopped suddenly.

All drilling operations

▪ Mark off the centre of the hole using a centre

punch or nail.

CHUCK REPLACEMENT

Chuck removal

Always wear eye protection.

Turn the torque adjustment collar/hammer selec

tion collar (2) to the “drill” position and low gear, on

the gear selector (13). Tighten the chuck around

the shorter end of a hex key (not supplied) of 5 mm

or greater size.

Using a wooden mallet or similar object, strike

the longer end in the clockwise direction. This will

loosen the screw inside the chuck.

1. Open chuck jaws fully.

2. Insert a 5 mm hex key into front of chuck be

tween jaws to engage screw head. Remove

screw by turning clockwise.

3. Place the hex key in chuck and tighten. Using

a wooden mallet or similar object, strike key

sharply in the anti-clockwise direction. This will

loosen the chuck so that it can be unscrewed by

hand.

Chuck installation

1. Screw the chuck on by hand as far as it will go

and insert screw (LH thread).

2. Tighten the chuck around the shorter end of hex

key (not supplied) strike the longer end in the

clockwise direction with a wooden mallet.

3. Remove the hex key and open the jaws fully.

Tighten the screw in the centre of the chuck

firmly, with the hex key in an anti-clockwise di

rection.

IX - Maintenance

WARNING. Always ensure that the tool is

switched off before making any adjustments or

maintenance procedures.

CLEANING

▪ Keep the tool’s air vents unclogged and clean at

all times.

▪ Remove dust and dirt regularly. Cleaning is best

done with a rag.

▪ Re-lubricate all moving parts at regular inter

vals.

CAUTION! Do not use cleaning agents to clean

the plastic parts of the tool. A mild detergent on a

damp cloth is recommended. Water must never

come into contact with the tool.

GENERAL INSPECTION

Regularly check that all the ﬁxing screws are tight.

They may vibrate loose over time.

pages-BUR15-18-[13mm].indd 8 22.3.2006 ã. 09:05:35

Instruction Manual EN

X - Warranty

The guarantee period for SPARKY power tools is

determined in the guarantee card.

Faults due to normal wear, overloading or improp

er handling will be excluded from the guarantee.

Faults due to defective materials implemented as

well as defects in workmanship will be corrected

free of charge through replacement or repair.

The complaints for defective SPARKY power

tools will be recognized if the machine is sent

back to the dealer or is presented to the author

ised warranty service centre undismantled, in its

initial condition.

Notes

Carefully read the entire Instruction Manual before

using this product.

With continuing product development changes

may have occurred which render the product

received slightly different to that shown in this in

struction manual. The manufacturer reserves the

right to change speciﬁcations without notice.

Speciﬁcations may differ from country to country.

pages-BUR15-18-[13mm].indd 9 22.3.2006 ã. 09:05:35

BUR 15E • BUR 18EFR

DEBALLAGE

Grâce aux techniques modernes de fabrication, il est improbable que votre outil soit défectueux ou qu’une

pièce soit manquante. Si toutefois vous trouvez une anomalie, n’utilisez pas l’outil avant que les pièces

aient été remplacées ou le défaut corrigé. Ne pas observer cette règle pourrait causer des blessures

graves.

MONTAGE

La perceuse sans ﬁl BUR 15E (BUR 18E) est emballée complètement montée.

Sommaire

I - Introduction ................................................................................................................................... 10

II - Caractéristiques techniques ........................................................................................................ 12

III - Instructions de sécurité générales pour les outillages électriques .......................................... 12

IV - Règles de sécurité complémentaires pour les perceuses ........................................................ 13

V - Règles complémentaires pour travail avec le chargeur ............................................................ 14

VI - Règles complémentaires pour travail avec les accumulateurs ................................................. 14

VII - Nomenclature ........................................................................................................................... A/15

VIII - Utilisation ....................................................................................................................................... 15

IX - Entretien ........................................................................................................................................ 17

X - Garantie ........................................................................................................................................ 17

I - Introduction

Votre nouvel instrument a été conçu et produit selon tous les standards de qualité pour répondre aux

exigences les plus élevées. Son exploitation est facile et sécurisée. Et avec une utilisation correcte il vous

servira longtemps.

ATTENTION

Lire attentivement les instructions avant d’utiliser votre nouvel outil. Prêter attention aux sections «Aver-

tissement» et «Attention». Votre outil électrique possède des caractéristiques qui facilitent votre travail.

Cet instrument a été conçu et produit selon toutes les exigences de sécurité pour que son usage et son

entretien soient faciles.

Ne pas jeter les outils électroportatifs avec les ordures ménagères !

Les déchets provenant d’outils électriques ne doivent pas être ramassés avec les ordures

ménagères. Prière de recycler sur les lieux qui y sont spécialement destinés. Contacter les

autorités locales ou un représentant pour des consultations concernant le recyclage.

RESPECT DE L’ENVIRONNEMENT

Récupération des matières premières plutôt qu’élimination des déchets.

En vue à la protection de l’environnement, les appareils, comme d’ailleurs leurs accessoires et

emballages, doivent pouvoir suivre chacun une voie de recyclage appropriée. Nos pièces en

matières artiﬁcielles ont été marquées en vue d’un recyclage sélectif des différents matériaux.

Portez des équipements de protection

adaptés: lunettes de protection, casque

anti-bruit et masque anti-poussière.

Double isolation pour une

meilleure sécurité..

pages-BUR15-18-[13mm].indd 10 22.3.2006 ã. 09:05:35

Instructions d’utilisation FR