Yamaha RX-V1000 Руководство пользователя

Категория
Синтезаторы
Тип
Руководство пользователя

Это руководство также подходит для

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Malaysia ID
V641380
OWNER’S MANUAL
MODE D’EMPLOI
RX-V1000
Natural Sound AV Receiver
Ampli-tuner audio-vidéo
U C A
RX-V1000
0100V1000(UCA)-cv1/4 8/29/0, 4:31 PM1
II
SAFETY INSTRUCTIONS
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
you to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
1 Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2 Retain Instructions – The safety and operating instructions
should be retained for future reference.
3 Heed Warnings – All warnings on the unit and in the operating
instructions should be adhered to.
4 Follow Instructions – All operating and other instructions
should be followed.
5 Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, etc.
6 Carts and Stands – The unit should be used only with a cart
or stand that is recommended by the manufacturer.
6A A unit and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
unit and cart combination to overturn.
7 Wall or Ceiling Mounting – The unit should be mounted to
a wall or ceiling only as recommended by the
manufacturer.
8 Ventilation – The unit should be situated so that its location
or position does not interfere with its proper ventilation. For
example, the unit should not be situated on a bed, sofa, rug,
or similar surface, that may block the ventilation openings;
or placed in a built-in installation, such as a bookcase or
cabinet that may impede the flow of air through the
ventilation openings.
9 Heat – The unit should be situated away from heat sources
such as radiators, stoves, or other appliances that produce
heat.
10 Power Sources – The unit should be connected to a power
supply only of the type described in the operating instructions or
as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into the
inside of the unit.
15 Damage Requiring Service – The unit should be serviced by
qualified service personnel when:
A. The power-supply cord or the plug has been damaged;
or
B. Objects have fallen, or liquid has been spilled into the
unit; or
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or
exhibits a marked change in performance; or
E. The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the unit
beyond those means described in the operating instructions.
All other servicing should be referred to qualified service
personnel.
17 Power Lines – An outdoor antenna should be located away
from power lines.
18 Grounding or Polarization – Precautions should be taken so
that the grounding or polarization is not defeated.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
I CAUTION
0101V1000_Cau_EN 8/29/0, 1:32 PM2
EnglishINTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
III
SAFETY INSTRUCTIONS
1. IMPORTANT NOTICE : DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC,
to use the product.
2. IMPORTANT : When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable/s supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE : This product has been tested and found to
comply with the requirements listed in FCC
Regulations, Part 15 for Class “B” digital devices.
Compliance with these requirements provides a
reasonable level of assurance that your use of this
product in a residential environment will not result in
harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions
found in the users manual, may cause interference
harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon
lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your equipment
by playing it at a safe level. One that lets the sound come through
loud and clear without annoying blaring or distortion – and, most
importantly, without affecting your sensitive hearing.
19 For US customers only:
Outdoor Antenna Grounding – If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against voltage
surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to
an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
ELECTRIC
SERVICE
EQUIPMENT
NEC
– NATIONAL ELECTRICAL CODE
FCC INFORMATION (for US customers only)
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume
levels.
Note to CATV system installer:
This reminder is provided to call the CATV system
installers attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
CAUTION II
0101V1000_Cau_EN 8/29/0, 1:32 PM3
IV
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this unit in a well ventilated, cool, dry, clean
place with at least 5 cm of ventilation space on the
top, right and left, and at the back of this unit
— away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold.
3 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds. To prevent fire or electrical
shock, do not place this unit where it may get
exposed to rain, water, and/or any type of liquid.
4 Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this
unit in a environment with high humidity (i.e. a room
with a humidifier) to prevent condensation inside
this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5 On the top of this unit, do not place:
Other components, as they may cause damage
and/or discoloration on the surface of this unit.
Buring objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
Containers with liquid in them, as they may cause
electrical shock to the user and/or damage to this
unit.
6 Do not cover the rear panel of this unit with a
newspaper, tablecloth, curtain, etc. in order not to
obstruct heat radiation. If the temperature inside
this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified
is dangerous and may cause fire, damage to this
unit, and/or personal injury. YAMAHA will not be
held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, disconnect the
power cord from the wall outlet during an electrical
storm.
14 Take care of this unit so that no foreign objects and/
or liquid drops inside this unit.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
15 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
16 When not planning to use this unit for long periods
of time (i.e. vacation), disconnect the AC power plug
from the wall outlet.
17 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
18 Before moving this unit, press STANDBY/ON to set
this unit in the standby mode, and disconnect the
AC power plug from the wall outlet.
19 VOLTAGE SELECTOR (China and general models
only)
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local main voltage
BEFORE plugging into the AC main supply.
Voltages are 110/120/220/240 V AC, 50/60 Hz.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is called
the standby mode. In this state, this unit is designed to
consume a very small quantity of power.
FREQUENCY STEP switch
(China and general models only)
Because the interstation frequency spacing differs in
different areas, set the FREQUENCY STEP switch
(locating at the rear) according to the frequency
spacing in your area.
North, Central and South America: 100 kHz/10 kHz
Other area: 50 kHz/9 kHz
Before setting this switch, disconnect the AC power
plug of this unit from the AC outlet.
IMPORTANT
Please record the serial number of this unit in the
space below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owners Manual in a safe place for future
reference.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
III CAUTION
0101V1000_Cau_EN 8/29/0, 1:32 PM4
1
EnglishINTRODUCTION PREPARATION
BASIC
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
ADVANCED
OPERATION
CONTENTS
INTRODUCTION
INTRODUCTION
CONTENTS........................................................... 1
FEATURES............................................................ 2
GETTING STARTED........................................... 3
Checking the Package Contents ............................... 3
Installing Batteries in the Remote Control ............... 3
CONTROLS AND FUNCTIONS ........................ 4
Front Panel ............................................................... 4
Remote Control ........................................................ 6
Using the Remote Control........................................ 8
Front Panel Display .................................................. 9
Rear Panel .............................................................. 10
PREPARATION
SPEAKER SETUP .............................................. 11
Speakers to Be Used............................................... 11
Speaker Placement ................................................. 11
CONNECTIONS ................................................. 12
Before Connecting Components ............................ 12
Connecting Audio Components ............................. 12
Connecting Video Components .............................. 14
Connecting the Speakers ........................................ 16
Connecting to an External Amplifier ..................... 18
Connecting an External Decoder ........................... 18
IMPEDANCE SELECTOR Switch ....................... 19
Connecting the Power Supply Cords ..................... 19
ON-SCREEN DISPLAY (OSD) ......................... 20
OSD Modes ............................................................ 20
Selecting the OSD Mode........................................ 20
SPEAKER MODE SETTINGS ......................... 21
Summary of SPEAKER SET Items
1A through 1F .................................................... 21
ADJUSTING THE SPEAKER
OUTPUT LEVELS ......................................... 22
Before You Begin ................................................... 22
Using the Test Tone (TEST DOLBY SUR.) .......... 23
BASIC OPERATION
BASIC PLAYBACK ........................................... 24
Input Modes and Indications .................................. 26
Selecting a Sound Field Program ........................... 28
Normal Stereo Reproduction.................................. 29
TUNING............................................................... 30
Connecting the Antennas........................................ 30
Automatic (or Manual) Tuning .............................. 31
Presetting Stations .................................................. 32
Tuning in to a Preset Station .................................. 33
Exchanging Preset Stations .................................... 34
BASIC RECORDING......................................... 35
ADVANCED OPERATION
SET MENU .......................................................... 36
Adjusting the Items on the SET MENU................. 36
1 SPEAKER SET (speaker mode settings)........... 37
2 LOW FRQ TEST ............................................... 40
3 L/R BALANCE (balance of the left and
right main speakers) ........................................... 41
4 HP TONE CTRL (headphone tone control) ....... 41
5 CENTER GEQ (center graphic equalizer)......... 41
6 INPUT RENAME .............................................. 41
7 I/O ASSIGNMENT ............................................ 41
8 INPUT MODE (initial input mode) ................... 42
9 PARAM. INI (parameter initialization) ............. 42
10 DOLBY D. SET (Dolby Digital set) ................ 42
11 DTS LFE LEVEL ............................................. 43
12 6.1/ES AUTO.................................................... 43
13 SP DELAY TIME ............................................. 43
14 DISPLAY SET.................................................. 44
15 MEMORY GUARD ......................................... 44
ADJUSTING THE LEVEL OF THE EFFECT
SPEAKERS...................................................... 45
SLEEP TIMER.................................................... 46
Setting the Sleep Timer .......................................... 46
Canceling the Sleep Timer ..................................... 46
REMOTE CONTROL FEATURES .................. 47
Control Area ........................................................... 47
Each Component Control Area .............................. 49
Setting the Manufacturer Code .............................. 54
Programming a New Remote Control Function
(Learn Feature)................................................... 55
Using the Macro Feature ........................................ 57
Changing the Source Name in
the Display Window........................................... 59
Clearing a Learned Function or Macro .................. 59
Clearing Learned Functions, Macros,
Renamed Source Names, and
Setup Manufacturer Codes................................. 60
ZONE 2 ................................................................ 61
Zone 2 Connections................................................ 61
Remote Control in Zone 2 ...................................... 62
ADDITIONAL INFORMATION
SOUND FIELD PROGRAM ............................. 63
Hi-Fi DSP Programs............................................... 63
CINEMA DSP Programs ........................................ 64
MOVIE THEATER Programs................................ 67
SOUND FIELD PROGRAM PARAMETER
EDITING ......................................................... 68
What is a sound field? ............................................ 68
Sound Field Program Parameters ........................... 68
Changing Parameter Settings ................................. 69
Resetting a Parameter to the Factory-set Value...... 69
Digital Sound Field Parameter Descriptions .......... 70
APPENDIX
TROUBLESHOOTING ..................................... 74
SPECIFICATIONS ............................................. 79
0102V1000_1-10_EN 8/29/0, 1:32 PM1
2
Thank you for selecting this YAMAHA AV receiver.
Built-in 5-Channel Power Amplifier
Minimum RMS Output Power
(0.04% THD, 20 Hz – 20 kHz)
Main: 100 W + 100 W (8 )
Center: 100 W (8 )
Rear: 100 W + 100 W (8 )
Maximum Power (EIAJ)
(10% THD, 1 kHz)
[China and general models]
Main: 140 W + 140 W (8 )
Center: 140 W (8 )
Rear: 140 W + 140 W (8 )
Multi-Mode Digital Sound Field
Processing
Digital Sound Field Processor (DSP)
Dolby Pro Logic decoder
Dolby Digital/Dolby Digital Matrix 6.1
Decoder
DTS/DTS ES Decoder
CINEMA DSP: Combination of YAMAHA
DSP Technology and Dolby Pro Logic, Dolby
Digital or DTS
Virtual CINEMA DSP
SILENT CINEMA DSP
Sophisticated AM/FM Tuner
40-Station Random Access Preset Tuning
Automatic Preset Tuning
Preset Station Shifting Capability (Preset
Editing)
Other Features
96-kHz/24-bit D/A Converter
“SET MENU” which Provides You with
15 Items for Optimizing This Unit for Your
Audio/Video System
Test Tone Generator for Easier Speaker Balance
Adjustment
6-Channel External Decoder Input for Other
Future Formats
BASS EXTENSION Button for Reinforcing
Bass Response
On Screen Display Function Helpful in
Controlling This Unit
S Video Signal Input/Output Capability
Component Video Input/Output Capability
Optical and Coaxial Digital Audio Signal
Jacks
Sleep Timer
Multi-Function Remote Control
Custom Installation Facility
FEATURES
Manufactured under license from Dolby Laboratories. “Dolby”,
“AC-3”, “Pro Logic”, “Surround EX” and the double-D symbol
are trademarks of Dolby Laboratories.
Confidential Unpublished Works. © 1992-1997 Dolby
Laboratories, Inc. All rights reserved.
Manufactured under license from Digital Theater Systems, Inc.
US Pat. No. 5,451,942 and other world-wide patents issued and
pending. “DTS”, “DTS Digital Surround” and “DTS ES” are
trademarks of Digital Theater Systems, Inc. Copyright 1996
Digital Theater Systems, Inc. All Rights Reserved.
y indicates a tip for your operation.
Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button
names differ between the main unit and the remote control for such operations, the button name on the remote control is given in
parentheses in this manual.
0102V1000_1-10_EN 8/29/0, 1:32 PM2
3
EnglishINTRODUCTION PREPARATION
BASIC
OPERAIONT
ADDITIONAL
INFORMATION
APPENDIX
ADVANCED
OPERATION
GETTING STARTED
Checking the Package Contents
Check your package to make sure it has the following items.
Remote control
Manganese batteries (3)
(AA, R6, UM-3)
Indoor FM antenna
(U.S.A., Canada, China
and general models)
AM loop antenna
Quick Reference Card
Installing Batteries in the Remote
Control
Insert the batteries in the correct direction by aligning the
+ and – marks on the batteries with the polarity markings
(+ and –) inside the battery compartment.
RESET button
Notes on batteries
Change the batteries periodically.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline
and manganese batteries) together. Read the packaging
carefully as these different types of batteries may have
the same shape and color.
Changing batteries
As the batteries lose power, the operating range of the
remote control decreases and the TRANSMIT indicator
does not flash or its light becomes dim. When you notice
any of these conditions, change all of the batteries.
After you have inserted new batteries, be sure to push
RESET in the battery compartment by using a ballpoint
pen or similar object before using the remote control.
(This does not clear the contents of the memory.)
If the remote control is without batteries for more than
3 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the manufacturer code and program
any acquired functions that may have been cleared.
TRANSMIT RE-NAME CLEAR
MACRO
MACROLEARN
OFF ON
SYSTEM
POWER
STANDBY
PHONO
V-AUX TUNER MD/TAPE CD-R CD
D-TV/LD CBL/SAT VCR 1 VCR 2/DVR DVD
6CH INPUT
TITLE
ENTER
MENU
SOUND
DISPLAY
SOURCE
SELECT
SEARCH CHAPTER
10KEY DSP HALL 1 HALL 2 CHURCH JAZZ CLUB
ROCK
CONCERT STADIUM
TV
SPORTS
ENTER-
TAINMENT
POWER REC STOP PAUSE PLAY
6.1/ES
MONO
MOVIE
MOVIE
THEATER 2
MOVIE
THEATER 1
/DTS
SUR.
0 +10 +100
1234
5678
9101112
++ +
TV VOL
A / B / C / D / E PRESET
TV INPUT
TV MUTE
CH
DISC
MUTE
EFFECT
VOLUME
+
/
CHP/INDEX
––
Note
If the batteries have leaked, dispose of them immediately.
Avoid touching the leaked material or letting it come into
contact with clothing, etc. Clean the battery compartment
thoroughly before installing new batteries.
(Australia and
Singapore models)
0102V1000_1-10_EN 8/29/0, 1:33 PM3
4
CONTROLS AND FUNCTIONS
Front Panel
1 STANDBY/ON
Turns on and sets this unit in the standby mode. When
you turn on this unit, you will hear a click and there will
be a 4 to 5-second delay before this unit can reproduce
sound.
Standby mode
In this mode, this unit consumes a small amount of
power to receive infrared-signals from the remote
control.
2 Remote control sensor
Receives signals from the remote control.
3 Front panel display
Shows information about the operational status of this
unit (see page 9).
4 INPUT MODE
Selects the mode of input for sources that send two or
more types of signals to this unit (see page 26).
You cannot control the input mode when you select 6CH
INPUT as the input source.
5 INPUT l / h
Selects the input source (DVD, D-TV/LD, CBL/SAT,
VCR 1, VCR 2/DVR, V-AUX, PHONO, CD, TUNER,
CD-R, MD/TAPE) you want to listen to or watch.
6 VOLUME
Controls the output level of all audio channels.
This does not affect the REC OUT level.
7 6CH INPUT
Selects the source connected to the 6CH INPUT jacks.
The source selected by pressing 6CH INPUT takes
priority over the source selected with INPUT l / h (or
the input selector buttons).
8 SPEAKERS A/B
Turn on or off the set of main speakers connected to the A
and/or B terminals on the rear panel.
9 BASS EXTENSION ON/OFF
When pushed in (ON), this feature boosts the bass
frequency of the left and right main channels by +6 dB
(60 Hz) while maintaining overall tonal balance. This
boost is useful if you do not use a subwoofer.
However, this boost may not be noticeable if “1B MAIN
SP” on the SET MENU is set to SMALL and “1E LFE/
BASS OUT” is set to SWFR.
0 PROCESSOR DIRECT ON/OFF
When pushed in (ON), BASS, TREBLE, and BASS
EXTENSION are bypassed, eliminating any alteration of
the original signal.
VCR2
/DVR
V-AUX
VCR 1
CBL/SAT
D-TV/LD
DVD
SOURCE
/REMOTE
REC OUT/ZONE 2
A/B/C/D/E
SPEAKERS
STANDBY
/ON
AB
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET/
TUNING
MD/TAPE
CD-R
TUNER
CD
PHONO
BASS
6CH INPUT
VOLUME
INPUT
INPUT MODE
+
TREBLE
+
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
FM/AM
PHONES S VIDEO VIDEO
L AUDIO R OPTICAL
SILENT
VIDEO AUX
EFFECT
PROGRAM
ON OFF
SURROUND
DIGITAL
DIGITAL
123 4567
89 0
q
w
e
rt yu
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
FM/AM
iopa
s
d
0102V1000_1-10_EN 8/29/0, 1:33 PM4
5
EnglishINTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
q REC OUT/ZONE 2
Selects the source you want to direct to the audio/video
recorder and ZONE 2 outputs independent of the source
you are listening to in the main room. When set to the
SOURCE/REMOTE position, the input source is directed
to all outputs.
w EFFECT
Switches the effect speakers (center, rear and rear center
(see page 17)) on and off. If you turn off the output of
these speakers by using EFFECT, all Dolby Digital and
DTS audio signals except for the LFE channel are
directed to the left and right main channels.
When Dolby Digital or DTS signals are mixed, the left
and right main channel signal levels may not match.
e A/B/C/D/E
Selects one of the 5 preset station groups (A to E).
r PROGRAM l / h
Selects the DSP program (see page 28).
t PRESET/TUNING l / h
Selects preset station number 1 to 8 when the colon (:)
appears next to the band indication on the front panel
display, and selects the tuning frequency when the colon
(:) does not appear.
y PHONES jack
Outputs audio signals for private listening with
headphones. When you connect headphones, no signals
are output to the PRE OUT jacks or to the speakers.
u VIDEO AUX jacks
Inputs audio and video signals from a portable external
source such as a game console. To reproduce source
signals from these jacks, select V-AUX as the input
source. To direct this source to the VCR 1 output jacks,
select V-AUX by using REC OUT/ZONE 2.
i PRESET/TUNING (EDIT)
Switches the function of PRESET/TUNING l / h (the
colon (:) turns on or off) between selecting a preset
station number and tuning.
This button is also used to exchange the assignment of
two preset stations with each other.
o FM/AM
Switches the reception band between FM and AM.
p MEMORY (MAN’L/AUTO FM)
Stores a station in the memory. Hold down this button for
more than 3 seconds to start automatic preset tuning.
a TUNING MODE (AUTO/MAN’L MONO)
Switches the tuning mode between automatic and manual.
To select the automatic tuning mode, press this button so
that the “AUTO” indicator lights up on the front panel
display. To select the manual tuning mode, press this
button so that the “AUTO” indicator does not light up.
s BASS
Adjusts the low-frequency response for the left and right
main channels.
Turn the control to the right to increase or to the left to
decrease the low-frequency response.
d TREBLE
Adjusts the high-frequency response for the left and right
main channels.
Turn the control to the right to increase or to the left to
decrease the high-frequency response.
Note
If you increase or decrease the high-frequency or the low-
frequency sound to an extreme level, the tonal quality from the
center, rear and rear center speakers may not match that of the
left and right main speakers.
Opening and closing the front
panel door
When you are not operating the controls behind the front
panel door, close the door.
To open, press gently on the lower part of the panel.
DIGITAL
0102V1000_1-10_EN 8/29/0, 1:33 PM5
6
CONTROLS AND FUNCTIONS
Remote Control
This section describes the basic operation of this unit with the remote control. See “REMOTE CONTROL FEATURES”
on pages 47 to 60 for full details.
ON SCREEN
LEVEL
SLEEP TEST
PARAMETER
SET MENU
TRANSMIT RE-NAME CLEAR
MACRO
MACROLEARN
OFF ON
SYSTEM
POWER
STANDBY
PHONO
V-AUX TUNER MD/TAPE CD-R CD
D-TV/LD CBL/SAT VCR 1 VCR 2/DVR DVD
6CH INPUT
TITLE
ENTER
MENU
SOUND
DISPLAY
SOURCE
SELECT
SEARCH CHAPTER
10KEY DSP HALL 1 HALL 2 CHURCH JAZZ CLUB
ROCK
CONCERT STADIUM
TV
SPORTS
ENTER-
TAINMENT
POWER REC STOP PAUSE PLAY
6.1/ES
MONO
MOVIE
MOVIE
THEATER 2
MOVIE
THEATER 1
/DTS
SUR.
0 +10 +100
1234
5678
9101112
++ +
TV VOL
A / B / C / D / E PRESET
TV INPUT
TV MUTE
CH
DISC
MUTE
EFFECT
VOLUME
+
/
CHP/INDEX
––
e
t
r
y
u
i
o
p
a
s
l
j
k
d
w
q
0
9
8
7
6
4
5
3
2
1
f
g
h
A
B
C
D
E
A Programming section
Provides a selection of programming types you can utilize to
conveniently operates your other components.
B A and B buttons
See page 47.
C Operation section
Provides functions such as play, stop, skip, etc. for operating
your other components.
D Others
Functions vary depending on your components that are set up
with the manufacturer code.
E Setup section
Sets speaker output levels, SET MENU, DSP parameters, etc.
0102V1000_1-10_EN 8/29/0, 1:33 PM6
7
EnglishINTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
2 TRANSMIT indicator
Flashes while the remote control is sending signals.
3 STANDBY
Sets this unit in the standby mode.
4 SYSTEM POWER
Turns on the power of this unit.
5 Input selector buttons
Select the input source.
6 Display window
Shows the selected source component that you are
controlling.
7 SOURCE SELECT k/n
Selects the source component without switching the
input.
8 10KEY/DSP
Selects the numeric button (10KEY) mode or DSP mode.
9 DSP program group/Numeric buttons
Select DSP programs or numbers according to the
position of 10KEY/DSP. (Press a button repeatedly to
select a DSP program within that group.)
0 6.1/ES
Turns on or off the Dolby Digital Matrix 6.1 or DTS ES
decoder with 10KEY/DSP set to the DSP position.
q A/B/C/D/E
Selects one of the 5 preset station groups.
w PRESET +/–
Selects a preset station number (1 to 8).
e RE-NAME
Used for changing the input source name in the display
window (see page 59).
r CLEAR
Used for clearing functions acquired when using the learn
and rename features, programmed macros, and set
manufacturer codes (see pages 59 and 60).
t LEARN
Used for setting up the manufacturer code or for
programming the functions of other remote controls (see
pages 54 to 56).
y MACRO
Used to program a series of operations for control by a
single button (see page 58).
u MACRO ON/OFF
Turns the macro function on and off.
i 6CH INPUT
Selects the source connected to the 6CH INPUT jacks.
o MUTE
Mutes the sound. Press again to restore the audio output
to the previous volume level.
p VOLUME +/–
Increases or decreases the volume level.
a EFFECT
Switches the effect speakers (center, rear and rear center
(see page 17)) on and off. If the output of these speakers
is turned off, all Dolby Digital and DTS audio signals
except for the LFE channel are directed to the left and
right main channels.
s Cover
Slides down to show the setup buttons.
d LEVEL
Selects the effect speaker channels (center, rear, rear
center (see page 17) and subwoofer) so you can adjust
their output level independently.
f ON SCREEN
Selects the on-screen display (OSD) mode for your video
monitor.
g SLEEP
Sets the sleep timer.
h TEST
Outputs the test tone.
j PARAMETER/SET MENU
Selects the PARAMETER mode or SET MENU mode.
k Cursor buttons k/n/–/+
Select and adjust DSP program parameters and SET
MENU items according to the position of PARAMETER/
SET MENU.
l RESET
Press this button after you have changed the batteries or
when the remote control stops working properly.
(Pressing RESET does not clear the acquired functions.)
0102V1000_1-10_EN 8/29/0, 1:33 PM7
8
CONTROLS AND FUNCTIONS
Using the Remote Control
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.
Handling the remote control
Do not spill water or other liquids on the remote
control.
Do not drop the remote control.
Do not leave or store the remote control in the
following types of conditions:
high humidity or temperature such as near a heater,
stove or bath;
dusty places; or
in places subject to extremely low temperatures.
STANDBY
/ON
+
+
30° 30°
TRANSMIT RE-NAME CLEAR
MACRO
MACROLEARN
OFF ON
SYSTEM
POWER
STANDBY
PHONO
V-AUX TUNER MD/TAPE CD-R CD
D-TV/LD CBL/SAT VCR 1 VCR 2/DVR DVD
6CH INPUT
TITLE
ENTER
MENU
SOUND
DISPLAY
SOURCE
SELECT
SEARCH CHAPTER
10KEY DSP HALL 1 HALL 2 CHURCH JAZZ CLUB
ROCK
CONCERT STADIUM
TV
SPORTS
ENTER-
TAINMENT
POWER REC STOP PAUSE PLAY
6.1/ES
MONO
MOVIE
MOVIE
THEATER 2
MOVIE
THEATER 1
/DTS
SUR.
0 +10 +100
1234
5678
9101112
++ +
TV VOL
A / B / C / D / E PRESET
TV INPUT
TV MUTE
CH
DISC
MUTE
EFFECT
VOLUME
+
/
CHP/INDEX
––
SURROUND
DIGITAL
DIGITAL
Approximately 6 m (20 feet)
0102V1000_1-10_EN 8/29/0, 1:33 PM8
9
EnglishINTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
Front Panel Display
1 t indicator
Lights up when the built-in DTS decoder is on.
2 VIRTUAL indicator
Lights up when using Virtual CINEMA DSP (see
page 29).
3 g and o indicators
Light up according to the type of Dolby signals this unit
is reproducing. “ g ” lights up when the built-
in Dolby Digital decoder is on. “ o ” lights up
when the built-in Dolby Pro Logic decoder is on.
4 x indicator
Lights up when you select a DSP program.
5 DSP program indicators
The name of the selected DSP program lights up when the
ENTERTAINMENT, MOVIE THEATER 1, MOVIE
THEATER 2 or q/DTS SURROUND DSP program is
selected.
6 STEREO indicator
Lights up when the unit is receiving a strong signal for an
FM stereo broadcast while the “AUTO” indicator is lit.
7 AUTO indicator
Shows that this unit is in the automatic tuning mode.
8 VOLUME level indicator
Indicates the volume level.
9 Input source indicator
Shows the current input source with the arrow-shaped
cursor.
0 c indicator
Lights up when the built-in Dolby Digital Matrix 6.1 or
DTS ES decoder is on.
q v indicator
Lights up when this unit is reproducing PCM (pulse code
modulation) digital audio signals.
w SP A/B indicator
Lights up according to which set of main speakers is
selected. Both indicators light up when both sets of
speakers are selected.
e Headphones indicator
Lights up when headphones are connected.
r Multi-information display
Shows the current DSP program name and other
information when adjusting or changing settings.
t MEMORY indicator
Flashes to show a station can be stored.
y TUNED indicator
Lights up when this unit tunes in to a station.
u ZONE 2 indicator
Lights up when you select the input source while the
remote control is in the Zone 2 mode (see pages 61
and 62).
i SLEEP indicator
Lights up while the sleep timer is on.
DIGITAL
DTS MOVIE THEATER 1
2
DOLBY DIGITAL
PRO LOGIC ENTERTAINMENT
DSP
6.1/ES
PCM
PRO LOGIC
A
SP
B
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
VIRTUAL
PS
PTY
RT
CT
PTY
HOLD
EON
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
ZONE 2
VOLUME
dB
ms
SLEEP
STEREO
AUTO
1
23
4
56
78
9
0q w
e
r
t
yu
i
0102V1000_1-10_EN 8/29/0, 1:33 PM9
10
CONTROLS AND FUNCTIONS
Rear Panel
1 DIGITAL INPUT jacks
2 DIGITAL OUTPUT jacks
3 Antenna input terminals
See page 30 for connection information.
4 Audio component jacks
See pages 12 and 13 for connection information.
5 Video component jacks
See pages 14 and 15 for connection information.
6 Speaker terminals
See pages 16 and 17 for connection information.
7 PRE OUT/MAIN IN jacks
See page 18 for connection information.
8 AC power cord
Connect to a power outlet.
9 VOLTAGE SELECTOR (China and general
models only)
See page 19.
0 q RF (AC-3) input jack (China and general
models only)
See page 14.
q REMOTE CONTROL IN/OUT jacks
See page 61 for details.
w RS-232C connector
This is a control expansion connector for commercial use.
Consult your dealer for details.
e 6CH INPUT jacks
See pages 13 and 18 for connection information.
r ZONE 2 OUT jacks
See page 61 for details.
t FREQUENCY STEP switch (China and
general models only)
See page 30.
y IMPEDANCE SELECTOR switch
Use this switch to match the amplifier output to your
speaker impedance. Set this unit in the standby mode
before you change the setting of this switch (see page 19).
u AC OUTLET(S)
Use these outlets to supply power to your other A/V
components (see page 19).
DIGITAL OUTPUT AUDIO AUDIO VIDEO
SPEAKERS PRE OUT/MAIN IN
MAIN
CENTER
REAR
(SURROUND)
TUNER
DIGITAL INPUT
REMOTE CONTROL
6CH INPUT
MD/
TAPE
CD-R
CD
CD-R
DVD
FM
ANT
AM
ANT
GND
GND
RS-
232C
IN
D-TV
/LD
75
UNBAL.
OPTICAL
OPTICAL
COAXIAL
COAXIAL:
SELECT BY SETMENU
CD
IN
(PLAY)
DVD
S VIDEO VIDEO COMPONENT
DVD
Y
P
B
/
C
B
P
R
/
C
R
S VIDEO VIDEO
D-TV
/LD
CBL
/SAT
IN
VCR 1
OUT
IN
VCR 2
/DVR
OUT
ZONE 2 OUT
MONITOR
OUT
100 kHz/10 kHz
50 kHz/ 9 kHz
R
MD/TAPE
CBL
/SAT
LD
RF
(AC-3)
OUT
OUT
(REC)
CD
PHONO
MAIN
CENTER
SUB
WOOFER
FREQUENCY
STEP
FM AM
SURROUND
IN
(PLAY)
CD-R
OUT
(REC)
L R L
MAIN
IN
MAIN
OUT
REAR
CENTER
CENTER
SUB
WOOFER
R L
LR
R
+
L
R L
D-TV/LD
A
Y
P
B
/
C
B
P
R
/
C
R
MONITOR
OUT
Y
P
B
/
C
B
P
R
/
C
R
+
+
+ +
B
REAR
(SURROUND)
MAIN A OR B: 4
MIN. /SPEAKER
A
+
B: 8
MIN. /SPEAKER
CENTER
: 6
MIN. /SPEAKER
REAR
: 6
MIN. /SPEAKER
MAIN A OR B: 8
MIN. /SPEAKER
A
+
B:
16
MIN. /SPEAKER
CENTER
: 8
MIN. /SPEAKER
REAR
: 8
MIN. /SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
SWITCHED
100W MAX. TOTAL
AC OUTLETS
VOLTAGE SELECTOR
1
23 4 5 6 7 8
9
q
0e
rt
w
u
y
(General
model)
0102V1000_1-10_EN 8/29/0, 1:33 PM10
11
EnglishINTRODUCTION PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SPEAKER SETUP
Speakers to Be Used
This unit has been designed to provide the best sound-
field quality with a 5-speaker system, using left and right
main speakers, left and right rear speakers and a center
speaker. The 6-speaker system, which adds a rear center
speaker to the 5 speaker configuration, is the latest
advancement in surround sound technology. (See page 17
for using the rear center speaker.) If you use different
brands of speakers (with different tonal qualities) in your
system, the tone of a moving human voice and other types
of sound may not shift smoothly. We recommend that you
use speakers from the same manufacturer or speakers
with the same tonal quality.
The main speakers are used for the main source sound
plus the effect sounds. They will probably be the speakers
from your present stereo system. The rear speakers are
used for the effect and surround sounds, and the center
speaker is for the center sounds (dialog, vocals, etc.). If
for some reason it is not practical to use a center speaker,
you can do without it. Best results, however, are obtained
with the full system.
The main speakers should be high-performance models
and have enough power-handling capacity to accept the
maximum output of your audio system. The other
speakers do not have to be equal to the main speakers.
For precise sound localization, however, it is ideal to use
high-performance models that can reproduce sounds over
the full range for the center speaker and the rear speakers.
Use of a subwoofer expands your
sound field
It is also possible to further expand your system with the
addition of a subwoofer. The use of a subwoofer is
effective not only for reinforcing bass frequencies from
any or all channels, but also for reproducing the LFE
(low-frequency effect) channel with high fidelity when
the Dolby Digital signal or the DTS signal is played back.
The YAMAHA Active Servo Processing Subwoofer
System is ideal for natural and lively bass reproduction.
Speaker Placement
Refer to the following diagram when you place the
speakers.
Main
speaker (L)
Center speaker
Main speaker (R)
Subwoofer
Rear speaker (R)
Rear center
speaker
See page 17.
Rear speaker (L)
Main speakers
Place the left and right main speakers an equal distance
from the ideal listening position. The distance of each
speaker from each side of the video monitor should be the
same.
Rear speakers
Place these speakers behind your listening position,
facing slightly inwards, nearly 1.8 m (approx. 6 feet)
above the floor.
Center speaker
Align the front face of the center speaker with the front
face of your video monitor. Place the speaker as close to
the monitor as possible, such as directly over or under the
monitor and centrally between the main speakers.
Note
If the center speaker is not used, the center channel sound will
be heard from the left and right main speakers. In this case,
“1A CENTER SP” on the SET MENU is set to NONE (see
page 38 for details).
Subwoofer
The position of the subwoofer is not so critical, because
low bass sounds are not highly directional. But it is better
to place the subwoofer near the main speakers. Turn it
slightly toward the center of the room to reduce the wall
reflections.
CAUTION
Some types of speakers interfere with a video monitor.
If this problem occurs, move the speakers away from
the monitor. If you cannot avoid installing the center
speaker or subwoofer near the video monitor, use a
magnetically shielded speaker.
PREPARATION
1.8 m
0103V1000_11-18_EN 8/29/0, 1:33 PM11
12
CONNECTIONS
Before Connecting Components
CAUTION
Never connect this unit and other components to mains power until all connections between components have been
completed.
Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some
components require different connection methods and have different jack names. Refer to the operation instructions
for each component to be connected to this unit.
When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or
changer), connect them to the jack with the same number labels as !, #, $ etc. YAMAHA applies this labeling
system to all its products.
After you have completed all connections, check them again to make sure they are correct.
Connecting Audio Components
Connecting to digital jacks
This unit has digital jacks for direct transmission of
digital signals through either coaxial or fiber optic cables.
You can use the digital jacks to input PCM, Dolby Digital
and DTS bitstreams. When you connect components to
both the COAXIAL and OPTICAL jacks, priority is given
to the input signals from the COAXIAL jack. All digital
input jacks are acceptable for 96-kHz sampling digital
signals (see page 25 for details).
y
You can designate the input for each digital jack according to
your component by using “7 I/O ASSIGNMENT” on the SET
MENU (see page 41 for details).
About the dust protection cap
Pull out the cap from the optical jack
before you connect the fiber optic cable.
Do not discard the cap. When you are not
using the optical jack, be sure to put the
cap back in place. This cap protects the
jack from dust.
Note
The OPTICAL jacks on this unit conform to the EIA standard.
If you use a fiber optic cable that does not conform to this
standard, this unit may not function properly.
Connecting a turntable
PHONO jacks are for connecting a turntable with an MM
or high-output MC cartridge. If you have a turntable with
a low-output MC cartridge, use an inline boosting
transformer or MC-head amplifier when connecting to
these jacks.
y
The GND terminal does not electrically ground the turntable. It
simply reduces noise in the signal. In some cases, you may
hear less noise if you do not connect to the GND terminal.
Connecting a CD player
y
The COAXIAL CD and OPTICAL CD jacks are available for a
CD player which has coaxial or optical digital output jacks.
When you connect a CD player to both the COAXIAL CD and
OPTICAL CD jacks, priority is given to the input signals from
the COAXIAL CD jack.
Connecting an MD recorder, tape
deck or CD recorder
y
Only digital signals input from a source such as a CD or DVD
are output from the DIGITAL OUTPUT jacks.
When you connect your recording component to both the
analog and digital input and output jacks, the priority is given
to the digital signal.
You can connect an MD recorder to any digital input jack by
using “7 I/O ASSIGNMENT” on the SET MENU (see
page 41).
Notes
When you connect a recording component to this unit, keep its
power on while using this unit. If the power is off, this unit
may distort the sound from other components.
When you record from a source component connected to this
unit while this unit is set in the standby mode, the recorded
sound may be distorted. To avoid this problem, turn on this
unit.
0103V1000_11-18_EN 8/29/0, 1:33 PM12
13
EnglishINTRODUCTION PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONNECTIONS
DIGITAL OUTPUT AUDIO AUDIO VIDEO
TUNER
DIGITAL INPUT
REMOTE CONTROL
6CH INPUT
MD/
TAPE
CD-R
CD
CD-R
DVD
FM
ANT
AM
ANT
GND
GND
RS-
232C
IN
D-TV
/LD
75
UNBAL.
OPTICAL
OPTICAL
COAXIAL
COAXIAL:
SELECT BY SETMENU
CD
IN
(PLAY)
DVD
S VIDEO VIDEO COMPONENT
DVD
Y
P
B
/
C
B
P
R
/
C
R
S VIDEO VIDEO
D-TV
/LD
CBL
/SAT
IN
VCR 1
OUT
IN
VCR 2
/DVR
OUT
ZONE 2 OUT
MONITOR
OUT
100 kHz/10 kHz
50 kHz/ 9 kHz
R
MD/TAPE
CBL
/SAT
LD
RF
(AC-3)
OUT
OUT
(REC)
CD
PHONO
MAIN
CENTER
SUB
WOOFER
FREQUENCY
STEP
FM AM
SURROUND
IN
(PLAY)
CD-R
OUT
(REC)
L R L
D-TV/LD
Y
P
B
/
C
B
P
R
/
C
R
MONITOR
OUT
Y
P
B
/
C
B
P
R
/
C
R
L
R
C
O
L
R
L
R
O
O
O
OUTPUT
GND
L
R
L R
L R
INPUT OUTPUT INPUTOUTPUT
OUTPUT
O
C
COAXIAL
OUTPUT
L
R
L
R
OPTICAL
OUTPUT
OPTICAL
INPUT
OPTICAL
INPUT
OPTICAL
OUTPUT
SUBWOOFER
OUTPUT
CENTER OUTPUT
MAIN
OUTPUT
SURROUND
OUTPUT
L R
indicates signal direction
indicates left analog cables
indicates right analog cables
indicates optical cables
indicates coaxial cables
MD recorder or
tape deck
CD recorder
CD player
Turntable
External decoder
See page 18.
(General model)
0103V1000_11-18_EN 8/29/0, 1:33 PM13
14
CONNECTIONS
y
Each type of video jack works independently. Signals input
through the composite video, S-video and component jacks are
output through the corresponding composite video, S-video,
and component jacks, respectively.
If you make S-video connections to this unit, it is not necessary
to make composite video connections. If both types of
connections are made, this unit gives priority to the S-video
signal.
You can designate the input for the COMPONENT VIDEO A
and B jacks according to your component by using “7 I/O
ASSIGNMENT” on the SET MENU (see page 41 for details).
Notes
Use a commercially available S-video cable when connecting to the S VIDEO jack, and commercially available video cables when
connecting to the COMPONENT VIDEO jacks.
When you are using the COMPONENT VIDEO jacks, check the details in the owners manual that came with the component being
connected.
VIDEO AUX jacks (on the front panel)
Y
P
B
/
C
B
P
R
/
C
R
Connecting Video Components
About the video jacks
There are three types of video jacks. Video signals input through the VIDEO jacks are the conventional composite video
signals. Video signals input through the S VIDEO jacks are separated into luminance (Y) and color (C) video signals.
The S-video signals achieve high-quality color reproduction. Video signals input through the COMPONENT VIDEO
jacks are separated into luminance (Y) and color difference (P
B
/C
B
, P
R
/C
R
) video signals. The jacks are also separated
into three for each signal. The description of the component video jacks may be different depending on the component
(e.g. Y, C
B
, C
R
/Y, P
B
, P
R
/Y, B-Y, R-Y etc.). Component video signals provide the best quality in picture reproduction.
If your video component has an S-video output or component video output, you can connect it to this unit. Connect the
S-video signal output jack on your video component to the S VIDEO jack or connect the component signal output jacks
on your video component to the COMPONENT VIDEO jacks.
VIDEO jack
(composite)
S VIDEO jack COMPONENT VIDEO jacks
Game console
About the q RF (AC-3) signal input jack (China and general models
only)
S VIDEO VIDEO
L AUDIO R OPTICAL
VIDEO AUX
AUDIO OUT R
AUDIO OUT L
VIDEO OUT
OPTICAL OUT
S VIDEO OUT
O
V
L
R
S
These jacks are used to connect any video input source
such as a game console to this unit.
LD
RF
(AC-3)
COAXIAL:
SELECT BY SETMENU
If your LD player has a Dolby Digital RF (AC-3) signal
output jack, connect it to the q RF (AC-3) input jack on
this unit. If the Dolby Digital RF (AC-3) and analog
signals are input at the same time, priority is given to the
RF signals. When you want to reproduce the Dolby
Digital RF (AC-3) signals, set the input mode to D.D. RF
by using INPUT MODE (see page 26).
Notes
The Dolby Digital RF (AC-3) signals cannot be output by
using the REC OUT selector. When you record sound or
images from an LD player, be sure to connect the player to
either the DIGITAL OPTICAL or analog audio jacks.
Even if you connect an LD player with the Dolby Digital RF
(AC-3) output jack to this unit, you cannot reproduce Dolby
Digital sound from all LD discs. You must playback an LD
encoded with Dolby Digital signals in order to take advantage
of the Dolby Digital sound.
0103V1000_11-18_EN 8/29/0, 1:33 PM14
15
EnglishINTRODUCTION PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONNECTIONS
L
S
R
V
C
O
DIGITAL OUTPUT AUDIO AUDIO VIDEO
TUNER
DIGITAL INPUT
REMOTE CONTROL
6CH INPUT
MD/
TAPE
CD-R
CD
CD-R
FM
ANT
AM
ANT
GND
GND
RS-
232C
IN
75
UNBAL.
OPTICAL
COAXIAL
COAXIAL:
SELECT BY SETMENU
CD
IN
(PLAY)
DVD
S VIDEO VIDEO COMPONENT
DVD
Y
P
B/
C
B
PR/
C
R
S VIDEO VIDEO
D-TV
/LD
CBL
/SAT
IN
VCR 1
OUT
IN
VCR 2
/DVR
OUT
ZONE 2 OUT
MONITOR
OUT
100 kHz/10 kHz
50 kHz/ 9 kHz
R
MD/TAPE
CBL
/SAT
LD
RF
(AC-3)
OUT
OUT
(REC)
CD
PHONO
MAIN
CENTER
SUB
WOOFER
FREQUENCY
STEP
FM AM
SURROUND
IN
(PLAY)
CD-R
OUT
(REC)
L R L
D-TV/LD
Y
P
B/
C
B
PR/
C
R
MONITOR
OUT
Y
P
B/
C
B
PR/
C
R
DVD
D-TV
/LD
OPTICAL
L
R
S VIDEO
OUTPUT
S VIDEO
OUTPUT
S VIDEO
OUTPUT
S VIDEO
INPUT
VIDEO
INPUT
S VIDEO
OUTPUT
AUDIO
OUTPUT
AUDIO
OUTPUT
AUDIO INPUT
AUDIO OUTPUT
COAXIAL
OUTPUT
OPTICAL
OUTPUT
RF
OUTPUT
OPTICAL
OUTPUT
VIDEO
OUTPUT
VIDEO
OUTPUT
AUDIO
OUTPUT
VIDEO
OUTPUT
S VIDEO
INPUT
VIDEO
OUTPUT
VIDEO
INPUT
O
V
S
O
L
R
L
R
L
R
V
S
COMPONENT
INPUT
COMPONENT
OUTPUT
COMPONENT
OUTPUT
V
S
V
V
S S
L
R
C
C
V
S
TV/digital TV or
LD player
DVD player
Note
(U.S.A., Canada, Australia and Singapore models only)
If your LD player has a Dolby Digital RF signal output jack,
connect it to this unit through an RF demodulator (separately
purchased).
Cable TV or
satellite tuner
VCR 1 or
VCR 2/DVR (digital
video recorder)
(General model)
Video monitor
LD player
indicates signal direction
indicates left analog cables
indicates right analog cables
indicates optical cables
indicates coaxial cables
indicates video cables
indicates S-video cables
0103V1000_11-18_EN 8/29/0, 1:33 PM15
16
CONNECTIONS
2
1
3
12
10 mm (3/8”)
Connecting the Speakers
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are
faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound
will be unnatural and lack bass.
CAUTION
Use speakers with the specified impedance shown on the rear panel of this unit.
Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could
damage the unit and/or speakers.
If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers
in your configuration after you finish connecting your speakers.
Speaker cables
A speaker cord is actually a pair of insulated cables
running side by side. One of the cables is colored or
shaped differently, perhaps with a stripe, groove or ridge.
1 Remove approx. 10 mm (3/8”) of insulation
from each of the speaker cables.
2 Twist the exposed wires of the cable
together to prevent short circuits.
Connecting to the SPEAKERS terminals
1 Unscrew the knob.
2 Insert one bare wire into the hole in the side
of each terminal.
3 Tighten the knob to secure the wire.
y
(U.S.A., Canada, Australia, China and general models only)
Banana plug connections are also possible. First, tighten the
knob and then insert the banana plug connector into the end of
the corresponding terminal.
Red: positive (+)
MAIN SPEAKERS terminals
One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either
of the MAIN A or B terminals.
REAR SPEAKERS terminals
A rear speaker system can be connected to these terminals.
CENTER SPEAKER terminals
A center speaker can be connected to these terminals.
Black: negative (–)
0103V1000_11-18_EN 8/29/0, 1:33 PM16
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86

Yamaha RX-V1000 Руководство пользователя

Категория
Синтезаторы
Тип
Руководство пользователя
Это руководство также подходит для

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ