Yamaha RX-V1000RDS Руководство пользователя

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND

YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Printed in Malaysia ID

V641400

RX-V1000RDS

Natural Sound AV Receiver

Ampli-tuner audio-vidéo

G B

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

RX-V1000RDS

0100V1000RDS-cv1/4 9/11/0, 6:04 PM1

II

1 To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2 Install this unit in a well ventilated, cool, dry, clean

place with at least 5 cm of ventilation space on the

top, right and left, and at the back of this unit

— away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold.

3 Locate this unit away from other electrical

appliances, motors, or transformers to avoid

humming sounds. To prevent fire or electrical

shock, do not place this unit where it may get

exposed to rain, water, and/or any type of liquid.

4 Do not expose this unit to sudden temperature

changes from cold to hot, and do not locate this

unit in a environment with high humidity (i.e. a

room with a humidifier) to prevent condensation

inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal

injury.

5 On the top of this unit, do not place:

– Other components, as they may cause damage

and/or discoloration on the surface of this unit.

– Buring objects (i.e. candles), as they may cause

fire, damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may cause

electrical shock to the user and/or damage to this

unit.

6 Do not cover the rear panel of this unit with a

newspaper, tablecloth, curtain, etc. in order not to

obstruct heat radiation. If the temperature inside

this unit rises, it may cause fire, damage to this

unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may

overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

11 Do not clean this unit with chemical solvents; this

might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used.

Using this unit with a higher voltage than specified

is dangerous and may cause fire, damage to this

unit, and/or personal injury. YAMAHA will not be

held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, disconnect the

power cord from the wall outlet during an electrical

storm.

14 Take care of this unit so that no foreign objects and/

or liquid drops inside this unit.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

15 Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any

service is needed. The cabinet should never be

opened for any reasons.

16 When not planning to use this unit for long periods

of time (i.e. vacation), disconnect the AC power

plug from the wall outlet.

17 Be sure to read the “TROUBLESHOOTING” section

on common operating errors before concluding that

this unit is faulty.

18 Before moving this unit, press STANDBY/ON to set

this unit in the standby mode, and disconnect the

AC power plug from the wall outlet.

This unit is not disconnected from the AC power

source as long as it is connected to the wall outlet,

even if this unit itself is turned off. This state is called

the standby mode. In this state, this unit is designed to

consume a very small quantity of power.

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

Note

• The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K.

Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED

IN ACCORDANCE WITH THE FOLLOWING

CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured BLUE must be connected

to the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

CAUTION

0101V1000RDS_Cau_EN 9/5/0, 4:41 PM2

1

EnglishINTRODUCTION PREPARATION

BASIC

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

ADVANCED

OPERATION

CONTENTS

INTRODUCTION

CONTENTS........................................................... 1

FEATURES............................................................ 2

GETTING STARTED........................................... 3

Checking the Package Contents ............................... 3

Installing Batteries in the Remote Control ............... 3

CONTROLS AND FUNCTIONS ........................ 4

Front Panel ............................................................... 4

Remote Control ........................................................ 6

Using the Remote Control ........................................ 8

Front Panel Display .................................................. 9

Rear Panel .............................................................. 10

PREPARATION

SPEAKER SETUP .............................................. 11

Speakers to Be Used............................................... 11

Speaker Placement ................................................. 11

CONNECTIONS ................................................. 12

Before Connecting Components ............................ 12

Connecting Audio Components ............................. 12

Connecting Video Components .............................. 14

Connecting the Speakers ........................................ 16

Connecting to an External Amplifier ..................... 18

Connecting an External Decoder ........................... 18

IMPEDANCE SELECTOR Switch ....................... 19

Connecting the Power Supply Cords ..................... 19

ON-SCREEN DISPLAY (OSD) ......................... 20

OSD Modes ............................................................ 20

Selecting the OSD Mode........................................ 20

SPEAKER MODE SETTINGS ......................... 21

Summary of SPEAKER SET Items

1A through 1F .................................................... 21

ADJUSTING THE SPEAKER

OUTPUT LEVELS ......................................... 22

Before You Begin ................................................... 22

Using the Test Tone (TEST DOLBY SUR.) .......... 23

BASIC OPERATION

BASIC PLAYBACK ........................................... 24

Input Modes and Indications .................................. 26

Selecting a Sound Field Program ........................... 28

Normal Stereo Reproduction.................................. 29

TUNING............................................................... 30

Connecting the Antennas........................................ 30

Automatic (or Manual) Tuning .............................. 31

Presetting Stations .................................................. 32

Tuning in to a Preset Station .................................. 33

Exchanging Preset Stations .................................... 34

RECEIVING RDS STATIONS .......................... 35

Description of RDS Data ....................................... 35

Changing the RDS Mode ....................................... 35

PTY SEEK Function .............................................. 36

EON Function ........................................................ 37

BASIC RECORDING......................................... 38

ADVANCED OPERATION

SET MENU .......................................................... 39

Adjusting the Items on the SET MENU................. 39

1 SPEAKER SET (speaker mode settings)........... 40

2 LOW FRQ TEST ............................................... 43

3 L/R BALANCE

(balance of the left and right main speakers) ..... 44

4 HP TONE CTRL (headphone tone control) ....... 44

5 CENTER GEQ (center graphic equalizer)......... 44

6 INPUT RENAME .............................................. 44

7 I/O ASSIGNMENT ............................................ 44

8 INPUT MODE (initial input mode) ................... 45

9 PARAM. INI (parameter initialization) ............. 45

10DOLBY D. SET (Dolby Digital set) .................. 45

11DTS LFE LEVEL .............................................. 46

126.1/ES AUTO ..................................................... 46

13SP DELAY TIME............................................... 46

14DISPLAY SET ................................................... 47

15MEMORY GUARD ........................................... 47

ADJUSTING THE LEVEL OF THE EFFECT

SPEAKERS...................................................... 48

SLEEP TIMER.................................................... 49

Setting the Sleep Timer .......................................... 49

Canceling the Sleep Timer ..................................... 49

REMOTE CONTROL FEATURES .................. 50

Control Area ........................................................... 50

Each Component Control Area .............................. 52

Setting the Manufacturer Code .............................. 57

Programming a New Remote Control Function

(Learn Feature)................................................... 58

Using the Macro Feature ........................................ 60

Changing the Source Name

in the Display Window....................................... 62

Clearing a Learned Function or Macro .................. 62

Clearing Learned Functions, Macros,

Renamed Source Names,

and Setup Manufacturer Codes .......................... 63

ADDITIONAL INFORMATION

SOUND FIELD PROGRAM ............................. 64

Hi-Fi DSP Programs............................................... 64

CINEMA DSP Programs ........................................ 65

MOVIE THEATER Programs................................ 68

SOUND FIELD PROGRAM PARAMETER

EDITING ......................................................... 69

What is a sound field? ............................................ 69

Sound Field Program Parameters ........................... 69

Changing Parameter Settings ................................. 70

Resetting a Parameter to the Factory-set Value ...... 70

Digital Sound Field Parameter Descriptions .......... 71

APPENDIX

TROUBLESHOOTING ..................................... 75

SPECIFICATIONS ............................................. 80

0102V1000RDS_1-10_EN 9/5/0, 4:41 PM1

2

Thank you for selecting this YAMAHA AV receiver.

Built-in 5-Channel Power Amplifier

◆ Minimum RMS Output Power

(0.04% THD, 20 Hz – 20 kHz)

Main: 100 W + 100 W (8 Ω)

Center: 100 W (8 Ω)

Rear: 100 W + 100 W (8 Ω)

Multi-Mode Digital Sound Field

Processing

◆ Digital Sound Field Processor (DSP)

◆ Dolby Pro Logic decoder

◆ Dolby Digital/Dolby Digital Matrix 6.1

Decoder

◆ DTS/DTS ES Decoder

◆ CINEMA DSP: Combination of YAMAHA

DSP Technology and Dolby Pro Logic, Dolby

Digital or DTS

◆ Virtual CINEMA DSP

◆ SILENT CINEMA DSP

Sophisticated AM/FM Tuner

◆ 40-Station Random Access Preset Tuning

◆ Automatic Preset Tuning

◆ Preset Station Shifting Capability (Preset

Editing)

◆ Multi-Function for RDS Broadcast Reception

Other Features

◆ 96-kHz/24-bit D/A Converter

◆ “SET MENU” which Provides You with

15 Items for Optimizing This Unit for Your

Audio/Video System

◆ Test Tone Generator for Easier Speaker Balance

Adjustment

◆ 6-Channel External Decoder Input for Other

Future Formats

◆ BASS EXTENSION Button for Reinforcing

Bass Response

◆ On Screen Display Function Helpful in

Controlling This Unit

◆ S Video Signal Input/Output Capability

◆ Component Video Input/Output Capability

◆ Optical and Coaxial Digital Audio Signal

Jacks

◆ Sleep Timer

◆ Multi-Function Remote Control

FEATURES

Manufactured under license from Dolby Laboratories. “Dolby”,

“AC-3”, “Pro Logic”, “Surround EX” and the double-D symbol

are trademarks of Dolby Laboratories.

Manufactured under license from Digital Theater Systems, Inc.

US Pat. No. 5,451,942 and other world-wide patents issued and

pending. “DTS”, “DTS Digital Surround” and “DTS ES” are

• y indicates a tip for your operation.

• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button

names differ between the main unit and the remote control for such operations, the button name on the remote control is given in

parentheses in this manual.

0102V1000RDS_1-10_EN 9/5/0, 4:41 PM2

3

EnglishINTRODUCTION PREPARATION

BASIC

OPERAIONT

ADDITIONAL

INFORMATION

APPENDIX

ADVANCED

OPERATION

GETTING STARTED

Checking the Package Contents

Check your package to make sure it has the following items.

Remote control

Manganese batteries (3)

(AA, R6, UM-3)

Indoor FM antenna

AM loop antenna

Quick Reference Card

Installing Batteries in the Remote

Control

Insert the batteries in the correct direction by aligning the

+ and – marks on the batteries with the polarity markings

(+ and –) inside the battery compartment.

RESET button

■ Notes on batteries

• Change the batteries periodically.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have

the same shape and color.

■ Changing batteries

As the batteries lose power, the operating range of the

remote control decreases and the TRANSMIT indicator

does not flash or its light becomes dim. When you notice

any of these conditions, change all of the batteries.

After you have inserted new batteries, be sure to push

RESET in the battery compartment by using a ballpoint

pen or similar object before using the remote control.

(This does not clear the contents of the memory.)

If the remote control is without batteries for more than

3 minutes, or if exhausted batteries remain in the

remote control, the contents of the memory may be

cleared. When the memory is cleared, insert new

batteries, set up the manufacturer code and program

any acquired functions that may have been cleared.

TRANSMIT RE-NAME CLEAR

MACRO

MACROLEARN

OFF ON

SYSTEM

POWER

STANDBY

PHONO

V-AUX TUNER MD/TAPE CD-R CD

D-TV/LD CBL/SAT VCR 1 VCR 2/DVR DVD

6CH INPUT

TITLE

ENTER

MENU

SOUND

DISPLAY

SOURCE

SELECT

SEARCH CHAPTER

10KEY DSP HALL 1 HALL 2 CHURCH JAZZ CLUB

ROCK

CONCERT STADIUM

TV

SPORTS

ENTER-

TAINMENT

POWER REC STOP PAUSE PLAY

6.1/ES

MONO

MOVIE

THEATER 2

MOVIE

THEATER 1

/DTS

SUR.

0 +10 +100

1234

5678

9101112

++ +

TV VOL

A / B / C / D / E PRESET

TV INPUT

TV MUTE

CH

DISC

MUTE

EFFECT

VOLUME

+–

/

CHP/INDEX

–– –

Note

• If the batteries have leaked, dispose of them immediately.

Avoid touching the leaked material or letting it come into

contact with clothing, etc. Clean the battery compartment

thoroughly before installing new batteries.

75-ohm/300-ohm antenna

adapter (U.K. model only)

0102V1000RDS_1-10_EN 9/5/0, 4:41 PM3

4

CONTROLS AND FUNCTIONS

Front Panel

1 STANDBY/ON

Turns on and sets this unit in the standby mode. When

you turn on this unit, you will hear a click and there will

be a 4 to 5-second delay before this unit can reproduce

sound.

Standby mode

In this mode, this unit consumes a small amount of

power to receive infrared-signals from the remote

control.

2 Remote control sensor

Receives signals from the remote control.

3 Front panel display

Shows information about the operational status of this

unit (see page 9).

4 INPUT MODE

Selects the mode of input for sources that send two or

more types of signals to this unit (see page 26).

You cannot control the input mode when you select 6CH

INPUT as the input source.

5 INPUT l / h

Selects the input source (DVD, D-TV/LD, CBL/SAT,

VCR 1, VCR 2/DVR, V-AUX, PHONO, CD, TUNER,

CD-R, MD/TAPE) you want to listen to or watch.

6 VOLUME

Controls the output level of all audio channels.

This does not affect the REC OUT level.

7 6CH INPUT

Selects the source connected to the 6CH INPUT jacks.

The source selected by pressing 6CH INPUT takes

priority over the source selected with INPUT l / h (or

the input selector buttons).

8 SPEAKERS A/B

Turn on or off the set of main speakers connected to the A

and/or B terminals on the rear panel.

9 BASS EXTENSION ON/OFF

When pushed in (ON), this feature boosts the bass

frequency of the left and right main channels by +6 dB

(60 Hz) while maintaining overall tonal balance. This

boost is useful if you do not use a subwoofer.

However, this boost may not be noticeable if “1B MAIN

SP” on the SET MENU is set to SMALL and “1E LFE/

BASS OUT” is set to SWFR.

0 PROCESSOR DIRECT ON/OFF

When pushed in (ON), BASS, TREBLE, and BASS

EXTENSION are bypassed, eliminating any alteration of

the original signal.

VCR2

/DVR

V-AUX

VCR 1

CBL/SAT

D-TV/LD

DVD

SOURCE

REC OUT

A/B/C/D/E

SPEAKERS

STANDBY

/ON

AB

BASS

EXTENSION

PROCESSOR

DIRECT

PRESET/

TUNING

MD/TAPE

CD-R

TUNER

CD

PHONO

BASS

6CH INPUT

VOLUME

INPUT

INPUT MODE

–

+

TREBLE

–

+

PRESET

/TUNING

EDIT

MEMORY

MAN'L/AUTO FM

TUNING

MODE

AUTO/MAN'L MONO

RDS MODE

/FREQ

EON PTY SEEK

MODE

START

FM/AM

PHONES S VIDEO VIDEO

L AUDIO R OPTICAL

SILENT

VIDEO AUX

EFFECT

PROGRAM

ON OFF

SURROUND

DIGITAL

123 4567

89 0

q

w

e

rt yu

hj

PRESET

/TUNING

EDIT

MEMORY

MAN'L/AUTO FM

TUNING

MODE

AUTO/MAN'L MONO

RDS MODE

/FREQ

EON PTY SEEK

MODE

START

FM/AM

i

o

pa

s

d

fg

0102V1000RDS_1-10_EN 9/5/0, 4:41 PM4

5

EnglishINTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

q REC OUT

Selects the source you want to direct to the audio/video

recorder outputs. When set to the SOURCE position, the

input source is directed to all outputs.

w EFFECT

Switches the effect speakers (center, rear and rear center

(see page 17)) on and off. If you turn off the output of

these speakers by using EFFECT, all Dolby Digital and

DTS audio signals except for the LFE channel are

directed to the left and right main channels.

When Dolby Digital or DTS signals are mixed, the left

and right main channel signal levels may not match.

e A/B/C/D/E

Selects one of the 5 preset station groups (A to E).

r PROGRAM l / h

Selects the DSP program (see page 28).

t PRESET/TUNING l / h

Selects preset station number 1 to 8 when the colon (:)

appears next to the band indication on the front panel

display, and selects the tuning frequency when the colon

(:) does not appear.

y PHONES jack

Outputs audio signals for private listening with

headphones. When you connect headphones, no signals

are output to the PRE OUT jacks or to the speakers.

u VIDEO AUX jacks

Inputs audio and video signals from a portable external

source such as a game console. To reproduce source

signals from these jacks, select V-AUX as the input

source. To direct this source to the VCR 1 output jacks,

select V-AUX by using REC OUT.

i PRESET/TUNING (EDIT)

Switches the function of PRESET/TUNING l / h (the

colon (:) turns on or off) between selecting a preset station

number and tuning.

This button is also used to exchange the assignment of

two preset stations with each other.

o FM/AM

Switches the reception band between FM and AM.

p MEMORY (MAN’L/AUTO FM)

Stores a station in the memory. Hold down this button for

more than 3 seconds to start automatic preset tuning.

a TUNING MODE (AUTO/MAN’L MONO)

Switches the tuning mode between automatic and manual.

To select the automatic tuning mode, press this button so

that the “AUTO” indicator lights up on the front panel

display. To select the manual tuning mode, press this

button so that the “AUTO” indicator does not light up.

DIGITAL

sRDS MODE/FREQ

When an RDS station is received, press this button to

change the display mode among the PS mode, PTY mode,

RT mode, CT mode (if the station offers those RDS data

services) and/or frequency display mode in turn.

d EON

Press this button to select the desired program type

(NEWS, INFO, AFFAIRS, SPORT) when you want to

tune in to a radio program of that type automatically.

f PTY SEEK MODE

Press this button to set the unit in the PTY SEEK mode.

g PTY SEEK START

Press this button to begin searching for a station after the

desired program type has been selected in the PTY SEEK

mode.

h BASS

Adjusts the low-frequency response for the left and right

main channels.

Turn the control to the right to increase or to the left to

decrease the low-frequency response.

j TREBLE

Adjusts the high-frequency response for the left and right

main channels.

Turn the control to the right to increase or to the left to

decrease the high-frequency response.

Note

• If you increase or decrease the high-frequency or the low-

frequency sound to an extreme level, the tonal quality from the

center, rear and rear center speakers may not match that of the

left and right main speakers.

■ Opening and closing the front

panel door

When you are not operating the controls behind the front

panel door, close the door.

To open, press gently on the lower part of the panel.

0102V1000RDS_1-10_EN 9/5/0, 4:41 PM5

6

CONTROLS AND FUNCTIONS

A Programming section

Provides a selection of programming types you can utilize to

conveniently operates your other components.

B A and B buttons

See page 50.

C Operation section

Provides functions such as play, stop, skip, etc. for operating

your other components.

D Others

Functions vary depending on your components that are set up

with the manufacturer code.

E Setup section

Sets speaker output levels, SET MENU, DSP parameters, etc.

Remote Control

This section describes the basic operation of this unit with the remote control. See “REMOTE CONTROL FEATURES”

on pages 50 to 63 for full details.

ON SCREEN

LEVEL

SLEEP TEST

PARAMETER

SET MENU

TRANSMIT RE-NAME CLEAR

MACRO

MACROLEARN

OFF ON

SYSTEM

POWER

STANDBY

PHONO

V-AUX TUNER MD/TAPE CD-R CD

D-TV/LD CBL/SAT VCR 1 VCR 2/DVR DVD

6CH INPUT

TITLE

ENTER

MENU

SOUND

DISPLAY

SOURCE

SELECT

SEARCH CHAPTER

10KEY DSP HALL 1 HALL 2 CHURCH JAZZ CLUB

ROCK

CONCERT STADIUM

TV

SPORTS

ENTER-

TAINMENT

POWER REC STOP PAUSE PLAY

6.1/ES

MONO

MOVIE

THEATER 2

MOVIE

THEATER 1

/DTS

SUR.

0 +10 +100

1234

5678

9101112

++ +

TV VOL

A / B / C / D / E PRESET

TV INPUT

TV MUTE

CH

DISC

MUTE

EFFECT

VOLUME

+–

/

CHP/INDEX

–– –

e

t

r

y

u

i

o

p

a

s

l

j

k

d

w

q

0

9

8

7

6

4

5

3

2

1

f

g

h

A

B

C

D

E

0102V1000RDS_1-10_EN 9/5/0, 4:41 PM6

7

EnglishINTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

1 Infrared window

Outputs infrared control signals. Aim this window at the

component you want to operate.

2 TRANSMIT indicator

Flashes while the remote control is sending signals.

3 STANDBY

Sets this unit in the standby mode.

4 SYSTEM POWER

Turns on the power of this unit.

5 Input selector buttons

Select the input source.

6 Display window

Shows the selected source component that you are

controlling.

7 SOURCE SELECT k/n

Selects the source component without switching the

input.

8 10KEY/DSP

Selects the numeric button (10KEY) mode or DSP mode.

9 DSP program group/Numeric buttons

Select DSP programs or numbers according to the

position of 10KEY/DSP. (Press a button repeatedly to

select a DSP program within that group.)

0 6.1/ES

Turns on or off the Dolby Digital Matrix 6.1 or DTS ES

decoder with 10KEY/DSP set to the DSP position.

q A/B/C/D/E

Selects one of the 5 preset station groups.

w PRESET +/–

Selects a preset station number (1 to 8).

e RE-NAME

Used for changing the input source name in the display

window (see page 62).

r CLEAR

Used for clearing functions acquired when using the learn

and rename features, programmed macros, and set

manufacturer codes (see pages 62 and 63).

t LEARN

Used for setting up the manufacturer code or for

programming the functions of other remote controls (see

pages 57 to 59).

y MACRO

Used to program a series of operations for control by a

single button (see page 61).

u MACRO ON/OFF

Turns the macro function on and off.

i 6CH INPUT

Selects the source connected to the 6CH INPUT jacks.

o MUTE

Mutes the sound. Press again to restore the audio output

to the previous volume level.

p VOLUME +/–

Increases or decreases the volume level.

a EFFECT

Switches the effect speakers (center, rear and rear center

(see page 17)) on and off. If the output of these speakers

is turned off, all Dolby Digital and DTS audio signals

except for the LFE channel are directed to the left and

right main channels.

s Cover

Slides down to show the setup buttons.

d LEVEL

Selects the effect speaker channels (center, rear, rear

center (see page 17) and subwoofer) so you can adjust

their output level independently.

f ON SCREEN

Selects the on-screen display (OSD) mode for your video

monitor.

g SLEEP

Sets the sleep timer.

h TEST

Outputs the test tone.

j PARAMETER/SET MENU

Selects the PARAMETER mode or SET MENU mode.

k Cursor buttons k/n/–/+

Select and adjust DSP program parameters and SET

MENU items according to the position of PARAMETER/

SET MENU.

l RESET

Press this button after you have changed the batteries or

when the remote control stops working properly.

(Pressing RESET does not clear the acquired functions.)

0102V1000RDS_1-10_EN 9/5/0, 4:41 PM7

8

CONTROLS AND FUNCTIONS

Using the Remote Control

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the main unit during operation.

■ Handling the remote control

• Do not spill water or other liquids on the remote

control.

• Do not drop the remote control.

• Do not leave or store the remote control in the

following types of conditions:

– high humidity or temperature such as near a heater,

stove or bath;

– dusty places; or

– in places subject to extremely low temperatures.

STANDBY

/ON

–

+

–

+

SURROUND

DIGITAL

30° 30°

0

1234

5678

9101112

++ +

+–

/

–– –

Approximately 6 m (20 feet)

0102V1000RDS_1-10_EN 9/5/0, 4:41 PM8

9

EnglishINTRODUCTION PREPARATION

BASIC

OPERAIONT

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONTROLS AND FUNCTIONS

Front Panel Display

1 t indicator

Lights up when the built-in DTS decoder is on.

2 VIRTUAL indicator

Lights up when using Virtual CINEMA DSP (see

page 29).

3 g and o indicators

Light up according to the type of Dolby signals this unit

is reproducing. “ g ” lights up when the built-

in Dolby Digital decoder is on. “ o ” lights up

when the built-in Dolby Pro Logic decoder is on.

4 x indicator

Lights up when you select a DSP program.

5 DSP program indicators

The name of the selected DSP program lights up when the

ENTERTAINMENT, MOVIE THEATER 1, MOVIE

THEATER 2 or q/DTS SURROUND DSP program is

selected.

6 PTY HOLD indicator

Lights up while searching for stations in the PTY SEEK

mode.

7 RDS mode indicators

The name(s) of the RDS data offered by the currently

received RDS station light(s) up. Illumination of the red

indicator next to the RDS data name shows that the

corresponding RDS mode is now selected.

8 EON indicator

Lights up when an RDS station that offers the EON data

service is being received.

9 STEREO indicator

Lights up when the unit is receiving a strong signal for an

FM stereo broadcast while the “AUTO” indicator is lit.

0 AUTO indicator

Shows that this unit is in the automatic tuning mode.

q VOLUME level indicator

Indicates the volume level.

w Input source indicator

Shows the current input source with the arrow-shaped

cursor.

e c indicator

Lights up when the built-in Dolby Digital Matrix 6.1 or

DTS ES decoder is on.

r v indicator

Lights up when this unit is reproducing PCM (pulse code

modulation) digital audio signals.

t SP A/B indicator

Lights up according to which set of main speakers is

selected. Both indicators light up when both sets of

speakers are selected.

y Headphones indicator

Lights up when headphones are connected.

u Multi-information display

Shows the current DSP program name and other

information when adjusting or changing settings.

i MEMORY indicator

Flashes to show a station can be stored.

o Program type name indicators

The name of the selected program type lights up when the

“EON” indicator lights up.

p TUNED indicator

Lights up when this unit tunes in to a station.

a SLEEP indicator

Lights up while the sleep timer is on.

DIGITAL

DTS MOVIE THEATER 1

2

DOLBY DIGITAL

PRO LOGIC ENTERTAINMENT

DSP

6.1/ES

PCM

PRO LOGIC

A

SP

B

D-TV/LD

CBL/SAT

VCR 1

VCR2/DVR

V-AUX

DVD

MD/TAPE

CD-R

TUNER

CD

PHONO

VIRTUAL

PS

PTY

RT

CT

PTY

HOLD

EON

STEREO

AUTO

NEWS INFO AFFAIRS SPORT

MEMORY TUNED

VOLUME

dB

ms

SLEEP

1 234 wq87



apio

6

uyre t

09 5

0102V1000RDS_1-10_EN 9/5/0, 4:41 PM9

10

CONTROLS AND FUNCTIONS

Rear Panel

1 DIGITAL INPUT jacks

2 DIGITAL OUTPUT jacks

3 Antenna input terminals

See page 30 for connection information.

4 Audio component jacks

See pages 12 and 13 for connection information.

5 Video component jacks

See pages 14 and 15 for connection information.

6 Speaker terminals

See pages 16 and 17 for connection information.

7 PRE OUT/MAIN IN jacks

See page 18 for connection information.

DIGITAL OUTPUT AUDIO AUDIO VIDEO

SPEAKERS

MAIN

CENTER

REAR

(SURROUND)

TUNER

DIGITAL INPUT 6CH INPUT

MD/

TAPE

CD-R

CD

DVD

FM

ANT

AM

ANT

GND

75

UNBAL.

D-TV

/LD

OPTICAL

COAXIAL

CD

IN

(PLAY)

DVD

S VIDEO VIDEO COMPONENT

DVD

Y

P

B

/

C

B

P

R

/

C

R

S VIDEO VIDEO

D-TV

/LD

CBL

/SAT

IN

VCR 1

OUT

IN

VCR 2

/DVR

OUT

MONITOR

OUT

R

MD/TAPE

CBL

/SAT

OUT

(REC)

CD

PHONO

MAIN

CENTER

SUB

WOOFER

SURROUND

IN

(PLAY)

CD-R

OUT

(REC)

L R L

CENTER

SUB

WOOFER

LR

R

+

–

L

R L

D-TV/LD

A

Y

P

B

/

C

B

P

R

/

C

R

MONITOR

OUT

Y

P

B

/

C

B

P

R

/

C

R

+

–

+

– –

+

B

REAR

(SURROUND)

MAIN A OR B: 4

MIN. /SPEAKER

A

+

B: 8

MIN. /SPEAKER

CENTER

: 6

MIN. /SPEAKER

REAR

: 6

MIN. /SPEAKER

MAIN A OR B: 8

MIN. /SPEAKER

A

+

B:

16

MIN. /SPEAKER

CENTER

: 8

MIN. /SPEAKER

REAR

: 8

MIN. /SPEAKER

IMPEDANCE SELECTOR

SET BEFORE POWER ON

SWITCHED

100W MAX. TOTAL

AC OUTLETS

RS-

232C

PRE OUT/MAIN IN

REAR

CENTER

R L

MAINS

MAIN

IN

MAIN

OUT

5

8

wq09

7

64321

(Europe model)

8 AC power cord

Connect to a power outlet.

9 RS-232C connector

This is a control expansion connector for commercial use.

Consult your dealer for details.

0 6CH INPUT jacks

See pages 13 and 18 for connection information.

q IMPEDANCE SELECTOR switch

Use this switch to match the amplifier output to your

speaker impedance. Set this unit in the standby mode

before you change the setting of this switch (see page 19).

w AC OUTLET(S)

Use these outlets to supply power to your other A/V

components (see page 19).

0102V1000RDS_1-10_EN 9/5/0, 4:41 PM10

11

EnglishINTRODUCTION PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

SPEAKER SETUP

Speakers to Be Used

This unit has been designed to provide the best sound-

field quality with a 5-speaker system, using left and right

main speakers, left and right rear speakers and a center

speaker. The 6-speaker system, which adds a rear center

speaker to the 5 speaker configuration, is the latest

advancement in surround sound technology. (See page 17

for using the rear center speaker.) If you use different

brands of speakers (with different tonal qualities) in your

system, the tone of a moving human voice and other types

of sound may not shift smoothly. We recommend that you

use speakers from the same manufacturer or speakers

with the same tonal quality.

The main speakers are used for the main source sound

plus the effect sounds. They will probably be the speakers

from your present stereo system. The rear speakers are

used for the effect and surround sounds, and the center

speaker is for the center sounds (dialog, vocals, etc.). If

for some reason it is not practical to use a center speaker,

you can do without it. Best results, however, are obtained

with the full system.

The main speakers should be high-performance models

and have enough power-handling capacity to accept the

maximum output of your audio system. The other

speakers do not have to be equal to the main speakers.

For precise sound localization, however, it is ideal to use

high-performance models that can reproduce sounds over

the full range for the center speaker and the rear speakers.

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the

addition of a subwoofer. The use of a subwoofer is

effective not only for reinforcing bass frequencies from

any or all channels, but also for reproducing the LFE

(low-frequency effect) channel with high fidelity when

the Dolby Digital signal or the DTS signal is played back.

The YAMAHA Active Servo Processing Subwoofer

System is ideal for natural and lively bass reproduction.

Speaker Placement

Refer to the following diagram when you place the

speakers.

Main

speaker (L)

Center speaker

Main speaker (R)

Subwoofer

Rear speaker (R)

Rear center

speaker

See page 17.

Rear speaker (L)

■ Main speakers

Place the left and right main speakers an equal distance

from the ideal listening position. The distance of each

speaker from each side of the video monitor should be the

same.

■ Rear speakers

Place these speakers behind your listening position,

facing slightly inwards, nearly 1.8 m (approx. 6 feet)

above the floor.

■ Center speaker

Align the front face of the center speaker with the front

face of your video monitor. Place the speaker as close to

the monitor as possible, such as directly over or under the

monitor and centrally between the main speakers.

Note

• If the center speaker is not used, the center channel sound will

be heard from the left and right main speakers. In this case,

“1A CENTER SP” on the SET MENU is set to NONE (see

page 41 for details).

■ Subwoofer

The position of the subwoofer is not so critical, because

low bass sounds are not highly directional. But it is better

to place the subwoofer near the main speakers. Turn it

slightly toward the center of the room to reduce the wall

reflections.

CAUTION

Some types of speakers interfere with a video monitor.

If this problem occurs, move the speakers away from

the monitor. If you cannot avoid installing the center

speaker or subwoofer near the video monitor, use a

magnetically shielded speaker.

PREPARATION

1.8 m

0103V1000RDS_11-18_EN 9/5/0, 4:41 PM11

12

CONNECTIONS

Before Connecting Components

CAUTION

Never connect this unit and other components to mains power until all connections between components have been

completed.

• Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some

components require different connection methods and have different jack names. Refer to the operation instructions

for each component to be connected to this unit.

• When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or

changer), connect them to the jack with the same number labels as !, #, $ etc. YAMAHA applies this labeling

system to all its products.

• After you have completed all connections, check them again to make sure they are correct.

Connecting Audio Components

■ Connecting to digital jacks

This unit has digital jacks for direct transmission of

digital signals through either coaxial or fiber optic cables.

You can use the digital jacks to input PCM, Dolby Digital

and DTS bitstreams. When you connect components to

both the COAXIAL and OPTICAL jacks, priority is given

to the input signals from the COAXIAL jack. All digital

input jacks are acceptable for 96-kHz sampling digital

signals (see page 25 for details).

y

• You can designate the input for each digital jack according to

your component by using “7 I/O ASSIGNMENT” on the SET

MENU (see page 44 for details).

About the dust protection cap

Pull out the cap from the optical jack

before you connect the fiber optic cable.

Do not discard the cap. When you are not

using the optical jack, be sure to put the

cap back in place. This cap protects the

jack from dust.

Note

• The OPTICAL jacks on this unit conform to the EIA standard.

If you use a fiber optic cable that does not conform to this

standard, this unit may not function properly.

■ Connecting a turntable

PHONO jacks are for connecting a turntable with an MM

or high-output MC cartridge. If you have a turntable with

a low-output MC cartridge, use an inline boosting

transformer or MC-head amplifier when connecting to

these jacks.

y

• The GND terminal does not electrically ground the turntable. It

simply reduces noise in the signal. In some cases, you may

hear less noise if you do not connect to the GND terminal.

■ Connecting a CD player

y

• The COAXIAL CD and OPTICAL CD jacks are available for a

CD player which has coaxial or optical digital output jacks.

• When you connect a CD player to both the COAXIAL CD and

OPTICAL CD jacks, priority is given to the input signals from

the COAXIAL CD jack.

■ Connecting an MD recorder, tape

deck or CD recorder

y

• Only digital signals input from a source such as a CD or DVD

are output from the DIGITAL OUTPUT jacks.

• When you connect your recording component to both the

analog and digital input and output jacks, the priority is given

to the digital signal.

• You can connect an MD recorder to any digital input jack by

using “7 I/O ASSIGNMENT” on the SET MENU (see

page 44).

Notes

• When you connect a recording component to this unit, keep its

power on while using this unit. If the power is off, this unit

may distort the sound from other components.

• When you record from a source component connected to this

unit while this unit is set in the standby mode, the recorded

sound may be distorted. To avoid this problem, turn on this

unit.

0103V1000RDS_11-18_EN 9/5/0, 4:41 PM12

13

EnglishINTRODUCTION PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

DIGITAL OUTPUT AUDIO AUDIO VIDEO

TUNER

DIGITAL INPUT 6CH INPUT

CD-R

DVD

FM

ANT

AM

ANT

GND

75

UNBAL.

D-TV

/LD

OPTICAL

COAXIAL

CD

IN

(PLAY)

DVD

S VIDEO VIDEO COMPONENT

DVD

Y

P

B

/

C

B

P

R

/

C

R

S VIDEO VIDEO

D-TV

/LD

CBL

/SAT

IN

VCR 1

OUT

IN

VCR 2

/DVR

OUT

MONITOR

OUT

R

MD/TAPE

CBL

/SAT

OUT

(REC)

CD

PHONO

MAIN

CENTER

SUB

WOOFER

SURROUND

IN

(PLAY)

CD-R

OUT

(REC)

L R L

D-TV/LD

Y

P

B

/

C

B

P

R

/

C

R

MONITOR

OUT

Y

P

B

/

C

B

P

R

/

C

R

RS-

232C

MD/

TAPE

CD

L

R

C

O

L

R

L

R

O

OUTPUT

GND

L

R

L R

INPUT OUTPUT INPUTOUTPUT

OUTPUT

O

C

COAXIAL

OUTPUT

L

R

L

R

OPTICAL

OUTPUT

OPTICAL

INPUT

OPTICAL

INPUT

OPTICAL

OUTPUT

SUBWOOFER

OUTPUT

CENTER OUTPUT

MAIN

OUTPUT

SURROUND

OUTPUT

L R

indicates signal direction

indicates left analog cables

indicates right analog cables

indicates optical cables

indicates coaxial cables

MD recorder or

tape deck

CD recorder

CD player

Turntable

External decoder

See page 18.

(Europe model)

0103V1000RDS_11-18_EN 9/5/0, 4:41 PM13

14

CONNECTIONS

y

• Each type of video jack works independently. Signals input

through the composite video, S-video and component jacks are

output through the corresponding composite video, S-video, and

component jacks, respectively.

• If you make S-video connections to this unit, it is not necessary

to make composite video connections. If both types of

connections are made, this unit gives priority to the S-video

signal.

• You can designate the input for the COMPONENT VIDEO A

and B jacks according to your component by using “7 I/O

ASSIGNMENT” on the SET MENU (see page 44 for details).

Notes

• Use a commercially available S-video cable when connecting to the S VIDEO jack, and commercially available video cables when

connecting to the COMPONENT VIDEO jacks.

• When you are using the COMPONENT VIDEO jacks, check the details in the owner’s manual that came with the component being

connected.

■ Video monitor with a 21-pin connector

Make a connection as shown on page 15 with a commercially available SCART-plug connector cable.

■ VIDEO AUX jacks (on the front panel)

Y

P

B

/

C

B

P

R

/

C

R

Connecting Video Components

■ About the video jacks

There are three types of video jacks. Video signals input through the VIDEO jacks are the conventional composite video

signals. Video signals input through the S VIDEO jacks are separated into luminance (Y) and color (C) video signals.

The S-video signals achieve high-quality color reproduction. Video signals input through the COMPONENT VIDEO

jacks are separated into luminance (Y) and color difference (P

B

/C

B

, P

R

/C

R

) video signals. The jacks are also separated

into three for each signal. The description of the component video jacks may be different depending on the component

(e.g. Y, C

B

, C

R

/Y, P

B

, P

R

/Y, B-Y, R-Y etc.). Component video signals provide the best quality in picture reproduction.

If your video component has an S-video output or component video output, you can connect it to this unit. Connect the

S-video signal output jack on your video component to the S VIDEO jack or connect the component signal output jacks

on your video component to the COMPONENT VIDEO jacks.

VIDEO jack

(composite)

S VIDEO jack COMPONENT VIDEO jacks

Game console

S VIDEO VIDEO

L AUDIO R OPTICAL

VIDEO AUX

AUDIO OUT R

AUDIO OUT L

VIDEO OUT

OPTICAL OUT

S VIDEO OUT

O

V

L

R

S

These jacks are used to connect any video input source

such as a game console to this unit.

0103V1000RDS_11-18_EN 9/5/0, 4:41 PM14

15

EnglishINTRODUCTION PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

DIGITAL OUTPUT AUDIO AUDIO VIDEO

TUNER

DIGITAL INPUT 6CH INPUT

MD/

TAPE

CD-R

CD

DVD

FM

ANT

AM

ANT

GND

75

UNBAL.

D-TV

/LD

OPTICAL

COAXIAL

CD

IN

(PLAY)

DVD

S VIDEO VIDEO COMPONENT

DVD

Y

P

B/

C

B

PR/

C

R

S VIDEO VIDEO

D-TV

/LD

CBL

/SAT

IN

VCR 1

OUT

IN

VCR 2

/DVR

OUT

MONITOR

OUT

R

MD/TAPE

CBL

/SAT

OUT

(REC)

CD

PHONO

MAIN

CENTER

SUB

WOOFER

SURROUND

IN

(PLAY)

CD-R

OUT

(REC)

L R L

D-TV/LD

Y

P

B/

C

B

PR/

C

R

MONITOR

OUT

Y

P

B/

C

B

PR/

C

R

RS-

232C

C

L

R

S VIDEO

OUTPUT

S VIDEO

OUTPUT

S VIDEO

OUTPUT

S VIDEO

INPUT

VIDEO

INPUT

S VIDEO

OUTPUT

*1

AUDIO

OUTPUT

AUDIO

OUTPUT

AUDIO INPUT

AUDIO OUTPUT

COAXIAL

OUTPUT

OPTICAL

OUTPUT

RF

OUTPUT

OPTICAL

OUTPUT

VIDEO

OUTPUT

VIDEO

OUTPUT

AUDIO

OUTPUT

VIDEO

OUTPUT

S VIDEO

INPUT

VIDEO

OUTPUT

VIDEO

INPUT

RF

INPUT

O

V

S

O

L

R

L

R

L

R

L

R

V

S

COMPONENT

INPUT

COMPONENT

OUTPUT

COMPONENT

OUTPUT

V

S

V

S S

L

R

C

VV

S

L

S

R

V

O

TV/digital TV or

LD player

DVD player

Cable TV or

satellite tuner

Note

• If your LD player has a Dolby Digital RF signal output jack,

connect it to this unit through an RF demodulator (separately

purchased).

VCR 1 or

VCR 2/DVR (digital

video recorder)

Video monitor

indicates signal direction

(Europe model)

LD player

RF

demodulator

indicates left analog cables

indicates right analog cables

indicates optical cables

indicates coaxial cables

indicates video cables

indicates S-video cables

No connection

SCART-plug

*1 You can connect the Dolby

Digital RF signal output of

your LD player to the

COAXIAL jack by using

“7 I/O ASSIGNMENT” on

the SET MENU (see

page 44).

0103V1000RDS_11-18_EN 9/5/0, 4:41 PM15

16

CONNECTIONS

Connecting the Speakers

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

CAUTION

• Use speakers with the specified impedance shown on the rear panel of this unit.

• Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could

damage the unit and/or speakers.

If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers

in your configuration after you finish connecting your speakers.

■ Speaker cables

A speaker cord is actually a pair of insulated cables

running side by side. One of the cables is colored or

shaped differently, perhaps with a stripe, groove or ridge.

1 Remove approx. 10 mm (3/8”) of insulation

from each of the speaker cables.

2 Twist the exposed wires of the cable together

to prevent short circuits.

■ Connecting to the SPEAKERS terminals

1 Unscrew the knob.

2 Insert one bare wire into the hole in the side

of each terminal.

3 Tighten the knob to secure the wire.

2

1

3

12

10 mm (3/8”)

Red: positive (+)

Black: negative (–)

■ MAIN SPEAKERS terminals

One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either

of the MAIN A or B terminals.

■ REAR SPEAKERS terminals

A rear speaker system can be connected to these terminals.

■ CENTER SPEAKER terminals

A center speaker can be connected to these terminals.

0103V1000RDS_11-18_EN 9/5/0, 4:41 PM16

17

EnglishINTRODUCTION PREPARATION

BASIC OPERA-

TION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

CONNECTIONS

SPEAKERS

MAIN

CENTER

REAR

(SURROUND)

CENTER

SUB

WOOFER

LR

R

+

–

L

R L

A

+

–

+

– –

+

B

REAR

(SURROUND)

MAIN A OR B: 4

MIN. /SPEAKER

A

+

B: 8

MIN. /SPEAKER

CENTER

: 6

MIN. /SPEAKER

REAR

: 6

MIN. /SPEAKER

MAIN A OR B: 8

MIN. /SPEAKER

A

+

B:

16

MIN. /SPEAKER

CENTER

: 8

MIN. /SPEAKER

REAR

: 8

MIN. /SPEAKER

IMPEDANCE SELECTOR

SET BEFORE POWER ON

SWITCHED

100W MAX. TOTAL

AC OUTLETS

PRE OUT/MAIN IN

REAR

CENTER

R L

MAINS

MAIN

IN

MAIN

OUT

Main speakers A

Right Left

Main speakers B

Right Left

(Europe model)

Center speaker Subwoofer

system

Subwoofer connection

See “SUBWOOFER jack”

on page 18.

Rear speakers

Right Left

Rear center

speaker

Power

amplifier

■ Using the rear center speaker

You can enjoy the Dolby Digital Surround EX software or DTS ES software by adding the rear center speaker to the 5-

speaker configuration.

Rear center speaker placement

Place the rear center speaker in the center between the left and right rear speakers at the same height from the floor as

the rear speakers.

Connecting the rear center speaker

1 Connect the PRE OUT REAR CENTER jack on this unit to the input jack on the separately

prepared power amplifier.

2 Connect the rear center speaker to the speaker terminals on this power amplifier.

Note

• Be sure to correctly connect the + terminal of the speaker to the + terminal on the power amplifier, and the – terminal of the speaker

to the – terminal on the power amplifier.

Setting up this unit for using the rear center speaker

When you use a rear center speaker, “1D REAR CT SP” on the SET MENU must be set to LRG or SML (see page 42).

Note

• No sound is output from the rear center speaker when “1C REAR L/R SP” on the SET MENU is set to NONE (see page 41 for

details).

0103V1000RDS_11-18_EN 9/5/0, 4:41 PM17

18

CONNECTIONS

Connecting to an External

Amplifier

If you want to increase the power output to the speakers,

or want to use another amplifier, connect an external

amplifier to the PRE OUT jacks as follows.

Note

• When RCA pin plugs are connected to the PRE OUT jacks for

output to an external amplifier, do not use the corresponding

SPEAKERS terminals.

1 MAIN jacks

• MAIN IN jacks

Line input to this unit’s main channel amplifiers.

• MAIN OUT jack

Main channel line output jacks.

Note

• The signals output through these jacks are affected by the

BASS, TREBLE and BASS EXTENSION settings.

2 REAR CENTER jack

Rear center channel line output jack.

3 CENTER jack

Center channel line output jack.

4 REAR (SURROUND) jacks

Rear channel line output jacks.

PRE OUT/MAIN IN

MAIN

IN

MAIN

OUT

REAR

CENTER

SUB

WOOFER

R L

LR

REAR

(SURROUND)

1

5

2

3

4

5 SUBWOOFER jack

When using a subwoofer with built-in amplifier,

including the YAMAHA Active Servo Processing

Subwoofer System, connect the input jack of the

subwoofer system to this jack.

Low bass signals distributed from the main, center and/or

rear channels are directed to this jack. (The cut-off

frequency of this jack is 90 Hz.) The LFE (low-frequency

effect) signals generated when Dolby Digital or DTS is

decoded are also directed if they are assigned to this jack.

Notes

• Adjust the volume level of the subwoofer with the control on

the subwoofer. The subwoofer volume cannot be adjusted from

this unit.

• Depending on the settings of “1 SPEAKER SET”, “10A LFE

LEVEL” and “11 DTS LFE LEVEL” on the SET MENU,

some signals may not be output from the SUBWOOFER jack.

Connecting an External Decoder

This unit is equipped with 6 additional input jacks (left

and right MAIN, CENTER, left and right SURROUND

and SUBWOOFER) for discrete multi-channel input from

an external decoder, sound processor or pre-amplifier.

Connect the output jacks on your external decoder to the

6CH INPUT jacks. Be sure to match the left and right

outputs to the left and right input jacks for the main and

surround channels.

Notes

• When you select 6CH INPUT as the input source, this unit

automatically turns off the digital sound field processor, and

you cannot listen to DSP programs.

• When you select 6CH INPUT as the input source, changing

items 1A to 1F on the SET MENU is not affected.

0103V1000RDS_11-18_EN 9/5/0, 4:41 PM18

Страница загружается...

Yamaha RX-V1000RDS Руководство пользователя

Похожие модели бренда