Yamaha PM1D Инструкция по применению

PM1D Manager V2

for Windows

Owner’s Manual

About the speciﬁcations of this software

Speciﬁcations of this software and the material given in this manual are subject to change without notice.

Copying or distributing this software and/or this manual in part or in whole using any method without the written per-

mission of Yamaha Corporation is prohibited.

Tr ad emarks

Windows is a registered trademark of Microsoft Corporation in the United States and other countries.

Pentium II is a registered trademark of Intel Corporation.

Compact Flash™ is a trademark of SanDisk Corporation.

Other company names and product names are trademarks and registered trademarks of their respective owners. Symbols

such as ® and TM are not explicitly given in this document.

The illustrations and LCD screens as shown in this owner’s manual are for instructional purposes only, and may

appear somewhat different from those on your instrument.

PM1D Manager V2 for Windows Owner’s Manual

Contents

About the “PM1D Manager V2 for Windows Owner’s Manual” . . . . . . . . . . . . . . . . . . . . . 3

Conventions in the “PM1D Manager V2 for Windows Owner’s Manual”. . . . . . . . . . . . . . 3

System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installing PM1D Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Uninstalling PM1D Manager. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Using the application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Exiting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Initialization procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Screens unique to PM1D Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Upper part of the display (common to all screens) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Lower part of the display (common to all screens). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Lower part of the function menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Option popup window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

REMOTE CONTROL SETUP popup window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Communication between PM1D Manager and the console/engine . . . . . . . . . . . . . . . . . 10

System connection examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Data communication method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Online operating procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Offline operating procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Cautions regarding data communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Remote Control functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Setup procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Remote control parameter list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Special considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

USB MIDI Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

About the “PM1D Manager V2 for Windows Owner’s Manual”

PM1D Manager V2 for Windows (subsequently referred

to as “PM1D Manager”) is an application program that

runs on a computer running Microsoft Windows (subse-

quently referred to as the “PC”), providing the same

operating environment as the software of the CS1D

(subsequently referred to as the “console”).

By using PM1D Manager, you can create various types of

settings even when you are away from the console, and

use a memory card (*) or other means to load settings

into the console at a later time. In addition, you can con-

nect the console/engine (DSP1D-EX {DSP1D}) to your

PC, and use it to control the entire system in the same

way as from the console.

This manual explains only items that are speciﬁc to

PM1D Manager; how to install the program, how to

connect your PC to the console/engine, and functional

limitations of operations from the PC.

For details on basic operation in each screen, please refer

to the “CS1D Reference Manual (Software)” contained

in the CS1D Owner’s Manual.

For details on terminology and basic operation for Win-

dows, please refer to the manual or Help ﬁles included

with Windows.

*For details on the memory cards that can be used, refer to

“CS1D Operation Manual (Basic Operation)” p.144, and

“CS1D Reference Manual (Hardware)” p.80 contained in

the CS1D Owner’s Manual.

Conventions in the “PM1D Manager V2 for Windows Owner’s Manual”

•

Distinguishing between the controls of the console

and the knobs/buttons of the software

The names of controls on the console (switches,

encoders) are enclosed in square brackets [ ] in order

to distinguish them from the knobs and buttons that

are displayed by the software.

Example: This is the same function as the DIRECT

RECALL [1]–[12] switches in the SCENE MEM-

ORY block of the console.

•

Va r ious icons

The left icon is used to indicate tips and ref-

erence pages.

Particularly important items or operations

you must use with care are marked by the

left icon.

System requirements

The following system is required in order to start up PM1D Manager.

•

An IBM PC/AT compatible computer with at least a

Pentium II 233 Mhz or equivalent CPU (Pentium II

350 Mhz or faster is recommended)

•

64 MB or more memory (128 MB or more is recom-

mended)

•

Supported operating systems:

Microsoft Windows 2000 / Microsoft Windows XP

Home Edition / Microsoft Windows XP Professional

•

Internet Explorer 4.0 or later must be installed

•

A display system with resolution of at least 800 x 600

pixels and 16 bit color (SVGA, High Color)

•

Hard disk free area of 10 MB or more

•

Mouse or other pointing device

•

CD-ROM drive

•

Serial port or USB port

*You will need an RS-232-C cable (cross-wired)

not exceeding 5 meters, or a USB cable not

exceeding 3 meters.

•

An ATA compatible PC CARD slot / CF (Compact

Flash) slot, or a PC CARD / CF card reader

Depending on your system and OS, a higher level of perfor-

mance may be required. A higher level of performance may

also be required if you are using a notebook PC.

For the latest version of the software and driver, and for

details on operating requirements, please refer to the follow-

ing URL.

http://www.yamahaproaudio.com/

Hint

PM1D Manager V2 for Windows Owner’s Manual

Installing PM1D Manager

This section explains how to install the PM1D Manager program.

If an older version of PM1D Manager is already

installed, you must ﬁrst uninstall it. (For the unin-

stallation procedure, refer to p.5.)

Before you begin the installation, you must exit all applica-

tions and memory-resident programs.

1. Insert the “PM1D SYSTEM SOFTWARE” CD-ROM

into your CD-ROM drive, and open the CD-ROM

drive from “My Computer.”

2. Inside the “WIN” folder, double-click the

“Setup.exe” icon.

The opening screen of the installer will appear.

Depending on your PC system, you may be asked to restart

the system during the installation process. If so, installation

will continue automatically after you restart.

3. As directed by the instructions on the screen, click

the “Next” button as needed to proceed to the next

step.

4. When the “Select Installation Folder” screen

appears, click the Browse button if necessary, spec-

ify the installation folder, and proceed to the next

step.

Continue following the on-screen instructions, and

installation will be completed.

When installation is complete, a shortcut icon will be

added to the Start menu and to the desktop.

Before you install the software, you must read the license agreement (licence_e.txt) found on the

“PM1D SYSTEM SOFTWARE” CD-ROM. You may use the software on the CD-ROM only if you

accept the terms of this license agreement.

Uninstalling PM1D Manager

There are two ways to uninstall PM1D Manager.

■

Using “Add or Remove Programs”

1. From the Windows “Start” menu, select “Start”-

(“Settings”)-“Control Panel.”

2. When the Control Panel opens, double-click the

“A dd or Remove Programs” icon.

3. Select the “PM1D Manager” item, and click

“Remove (Change/Remove).”

PM1D Manager and related ﬁles will be deleted from

the hard disk. (For details on the procedure, refer to

your Windows manual.)

■

Using Setup.exe

1. Perform steps 1–3 of “Installing PM1D Manager.”

A screen will appear asking you to select either

“Repair PM1D Manager” or “Remove PM1D Man-

ager.”

2. Check the “Remove PM1D Manager,” and click the

“Finish” button.

The software will be uninstalled.

If you selected Repair PM1D Manager, the software will not

be removed.

Using the application

This section explains how to start and exit PM1D Manager, and how to perform basic operations.

Starting

You can use either of the following methods to start up

PM1D Manager.

From the Windows “Start” menu, select “Start”-

“Programs”-“YAMAHA PM1D System”-“PM1D

Manager”

Double-click the PM1D Manager icon that was cre-

ated during the installation.

It is not possible for multiple instances of PM1D Manager to

be running simultaneously.

Hint

Yo u may ﬁnd it convenient to set your screen display resolu-

tion to 800 x 600, since PM1D Manager can start up in full-

screen display mode. However in this case, the menu bar will

not be displayed.

Exiting

You can use any of the following methods to exit PM1D

Manager.

In the lower left of the Function menu screen, click

the EXIT button.

Open the “File” menu and select “Exit.”

Click the “Close” button of the window.

Select “Close” from the “PM1D Manager” button in

the task bar.

Press Alt+F4 from the keyboard.

A popup window will ask you to conﬁrm that you want to

exit. To exit the application, click the OK button.

If you are using PM1D Manager with an 800

600 pixel

display, methods

–

cannot be used.

Hint

The next time PM1D Manager is started up, the state in

which you exited will automatically be restored.

PM1D Manager V2 for Windows Owner’s Manual

Basic operation

Operation in each screen is the same as on the console

itself. Refer to “CS1D Reference Manual (Software)”

contained in the CS1D Owner’s Manual. Mention of the

console’s track pad should be read as referring to the

mouse/pointing device of your PC.

Initialization procedure

If you want to initialize all current settings of the PM1D

Manager and its scene memories and libraries, you can

use the following procedure to restore the factory-set

condition.

1. In the Function menu screen, click the OPTION

button.

The Option settings popup window will appear.

2. According to the content that you want to initialize,

click either the “Initialize All Memories” button or

the “Initialize Current Memories” button.

•

If you click the “Initialize All Memories” button

The current settings of the PM1D Manager, as well as

the scene memories and the various libraries will be

initialized to the factory-set condition.

•

If you click the “Initialize Current Memories” but-

ton

The current settings of the PM1D Manager will be

initialized. However, scene memories and the various

libraries will not be affected.

When you press either of these buttons, a dialog box

will appear, asking you to conﬁrm the initialization.

3. To execute the initialization, click the OK button.

Memories that have been initialized cannot be recovered.

Please use great care when performing this operation.

Memory initialization can be performed only when ofﬂine.

Hint

For details on the Option popup window, refer to the expla-

nation on p.8.

Screens unique to PM1D Manager

This section explains the screens that differ from the console and are unique to PM1D Manager.

Upper part of the display (common to all screens)

Connection status

This area of the PM1D Manager screen will indicate

the status of the connection between the PC and con-

sole or engine.

•

...........Indicates that a cable is con-

nected between the console/

engine and the PC, but

communication has not

been established.

•

...........Indicates that a cable is con-

nected between the console/

engine and the PC, and that

communication has been

established. In this state, the

PM1D system can be con-

trolled from the PC.

•

...........Indicates that either the

cable is not connected, or

that the other device is not

powered-on.

Connection destination / connection method

The connector (COM port name or USB port name)

that is selected in the Communication Port (Option

menu) of Communication Setup.

Lower part of the display (common to all screens)

RECALL button / MUTE button

Select the function of the DIRECT RECALL/MUTE

MASTER 1–12 buttons (

) from the following two

choices.

•

DIRECT RECALL

You can use the DIRECT RECALL/MUTE MAS-

TER 1–12 buttons to directly recall the scenes

assigned to direct recall numbers 1–12. For details

on how to assign a scene to a direct recall number,

refer to “CS1D Reference Manual (Software)” con-

tained in the CS1D Owner’s Manual.

•

MUTE MASTER

You can use the DIRECT RECALL/MUTE MAS-

TER 1–12 buttons to turn muting on/off for mute

groups 1–12.

Hint

These two buttons have the same function as the MODE but-

ton in the MUTE GROUP ASSIGN screen of the IN DCA/

MUTE function and OUT DCA/MUTE function, and the

MODE button in the DIRECT RECALL screen of the SCENE

function.

DIRECT RECALL/MUTE MASTER 1–12 buttons

Depending on the setting of the RECALL button /

MUTE button (

), these buttons function either as

direct recall or mute master buttons.

These have the same function as the DIRECT

RECALL [1]–[12] switches in the SCENE MEMORY

block of the console.

PM1D Manager V2 for Windows Owner’s Manual

Lower part of the function menu

EXIT button

This button exits the PM1D Manager application.

This button has the same result as selecting “Exit”

from the “File” menu in the menu bar, or clicking the

“Close” button in the upper right of the PM1D Man-

ager window.

OPTION button

This button is used to make communication-related

settings or to initialize the memory. When you click

this button, the Option popup window will appear.

ONLINE/OFFLINE button

This button initiates or terminates communication.

When the button is on, PM1D Manager is online.

When the button is off, PM1D Manager is ofﬂine.

If the console/engine and the PC are not connected

by a cable, or if communication is not possible

because the communication settings are inappropri-

ate, the button will be grayed, and cannot be clicked.

ABOUT button

This button accesses a popup window that displays

the PM1D Manager version number and other infor-

mation about the software.

REMOTE ONLINE/OFFLINE button

This button switches the Remote Control function

on/off. The button indicates ONLINE when PM1D

Manager is synchronized with the remote controller,

and OFFLINE when it is off.

If the remote controller is not connected to the PC

via USB cable, or if communication is not possible

because the communication settings are inappropri-

ate, this button is grayed-out and cannot be clicked.

Option popup window

To open the Option popup window, click the

OPTION button located at the lower left of the func-

tion menu screen, or choose [Manager] from the

[Option] menu of the menu bar.

Communication Setup

•

Communication Port

From the pulldown menu, select the port that will

be used for communication. Only COM ports 1–9

are supported.

•

Meter Request

Select whether the meter movements displayed in

various screens of the console will also be displayed

in PM1D Manager. If this is turned ON, the con-

sole’s meter movements can also be viewed in

PM1D Manager.

•Please be aware that if Meter Request is turned ON, the

communication load will be higher.

•Depending on the PC system you are using and on the

frequency of operations on the console, the load may

exceed the allowable limit, causing communication with

the PC to be terminated for safety’s sake, and placing

PM1D Manager ofﬂine. If this occurs, turning Meter

Request OFF may solve the problem.

•If you do not require meter display, we recommend that

you turn Meter Request OFF.

Remote Control Setup

•

Out Port

•

In Port

Here you can select the USB input port (IN PORT)

and output port (OUT PORT) used for communi-

cation with the remote controller.

Memory Setup

Here you can reset the current PM1D Manager set-

tings and memories/libraries to the condition in

which they were immediately following installation.

Each button has the following function.

•

Initialize All Memories button

When you click this button, the current settings of

the PM1D Manager as well as the scene memories

and the various libraries will all be initialized to the

factory-set condition.

•

Initialize Current Memories button

When you click this button, the current settings of

the PM1D Manager will be initialized. (However,

the scene memories and the various libraries will

1 2 3 4 5

Screens unique to PM1D Manager

not be affected.) The following data will be initial-

ized.

–Current scene settings

–Current unit settings

–Current patch settings

–Name assigned in the NAME function of each

function

–Setup data (internal parameters not stored in

the scene)

Memory initialization can be performed only when

ofﬂine.

OK button

When you click this button, the settings that you

modiﬁed in Communication Setup will be ﬁnalized,

and the popup window will close.

5 CANCEL button

When you click this button, the settings that you

modiﬁed in Communication Setup will be discarded,

and the popup window will close.

REMOTE CONTROL SETUP popup window

To open the REMOTE CONTROL SETUP popup

window, choose [Remote Control Setup] from the

[Option] menu of the menu bar. In this window you

can make settings related to remote control (→p.14).

1 REMOTE MACHINE

When the system goes online, or when you click the

RE-SYNCHRONIZE button to establish synchroni-

zation, this ﬁeld will indicate the model name

(DM2000 V2, 02R96 V2, DM1000 V2) of the remote

controller from the MIDI port. You can also select

the model name manually, even if no remote con-

troller is connected.

2 RE-SYNCHRONIZE

This button obtains remote controller model infor-

mation from the speciﬁed MIDI port. It also trans-

mits PM1D Manager parameter data to the remote

controller.

3 ONLINE/OFFLINE indication

This will indicate ONLINE when communication

with the remote controller has been established.

4 CH ASSIGN

Here you can assign the correspondence between

input channels of the remote controller and input

channels of the PM1D, in units of two channels. If

you don’t want to make an assignment, choose “NO

ASSIGN.”

5 SCENE ASSIGN

Here you can select the PM1D scene memory num-

bers that correspond to scene memory numbers 00–

99 of the remote controller.

6 MIX ASSIGN

Here you can select the PM1D’s MIX channels that will

correspond to the remote controller’s AUX channels 1–

8 (or 1–12 on the DM2000 V2). By operating the AUX

channels of the remote controller you can control the

corresponding MIX channels of the PM1D.

7 MATRIX ASSIGN

Here you can select the PM1D’s MATRIX channels

that will correspond to the remote controller’s BUS

channels 1–8. By controlling the BUS channels of the

remote controller you can control the corresponding

MATRIX channels of the PM1D.

8 STEREO ASSIGN

Here you can select the PM1D’s STEREO channel

(STEREO A or B) that will correspond to the remote

controller’s STEREO channel.

9 AT T

This selects whether ATT operations on the remote

controller will control the PM1D’s ATT or its HA

GAIN (or digital gain).

0 IN EQ LOW

This selects whether LOW band EQ operations on an

input channel of the remote controller will control

the PM1D’s LOW band EQ or its HPF.

A OUT EQ

This selects the set of four bands on the PM1D’s

input channel EQ that will be controlled by operat-

ing the four-band EQ of an output channel on the

remote controller.

LOW: SUB LOW, LOW, LOW MID, MID bands

HIGH: LOW MID, MID, HIGH MID, HIGH bands

B EXIT

Closes the REMOTE CONTROL SETUP popup win-

dow.

0 A B

PM1D Manager V2 for Windows Owner’s Manual

Communication between PM1D Manager and the console/engine

If you connect the console/engine and the PC, you can use PM1D Manager as a supplementary controller for

the system.

• “Online” refers to a state in which the console/

engine and the PC are connected by a cable, and data

can be transferred to control the device immediately.

• “Ofﬂine” refers to a state in which the console/

engine and the PC are not connected by a cable and

therefore are unable to communicate, or a state in

which the cable is connected but communication has

not begun.

In the online state, parameters (with some excep-

tions) will be linked between the console/engine and

the PC, allowing PM1D Manager to monitor the

state of the system, operate it remotely, and act as a

substitute in the event of device failure. The material

that follows will explain various ways of setting up

the system, and how data communications can be

established and terminated.

System connection examples

■ Example 1: Standard mode (connect the PC

to the console)

Console×1, Engine×1

■ Example 2: Standard mode (connect the PC

to the engine)

■ Example 3: Mirror mode (connect the PC to

the console)

Console×1, Engine×2 (mirror mode)

■ Example 4: Mirror mode (connect the PC to

the engine)

Console×1, Engine×2 (mirror mode)

• The PC can only be connected to the engine that is

selected in Mirror mode. In this example, ENGINE A

is used.

• The PC can only be connected to the engine that is

selected in Mirror mode. In this example, ENGINE B

is used.

■ Example 5: Normal mode (connect the PC to

the engine)

Engine×1

•Only one PC can be connected to a system. It is not possi-

ble to connect multiple PC’s to a system.

•Depending on the device to which the PC is connected, or

depending on the structure of the system, the functional-

ity of PM1D Manager may be partially limited. For

details, refer to “PC connections in a system that includes

a console” (→p.21).

CONSOLE

(CS1D)

ENGINE

(DSP1D)

CONSOLE

(CS1D)

ENGINE

(DSP1D)

CONSOLE

(CS1D)

ENGINE A

(DSP1D)

ENGINE B

(DSP1D)

CONSOLE

(CS1D)

ENGINE A

(DSP1D)

ENGINE B

(DSP1D)

CONSOLE

(CS1D)

ENGINE A

(DSP1D)

ENGINE B

(DSP1D)

ENGINE

(DSP1D)

Communication between PM1D Manager and the console/engine

■ System example 6: Dual Console mode

•You can connect and use either PC1 or PC2 (not

both).

•Even if a PC is connected to console 2, it cannot

be used.

■ System example 7: Cascade connection

•You can connect and use either PC1 or PC2 (not

both), and PC3 or PC4 (not both).

•Even if there is no console, just an engine and PC

can be used as a system.

Connections

Connect the console/engine to your PC as shown in the following diagram. You can make connections in one of two

ways: serial connection or USB connection.

• When using USB connections, you must exit PM1D

Manager before you power-on/off the console/engine or

connect/disconnect cables. If you perform these actions

before exiting, communication may become impossible

until you restart your PC.

• USB connection is not guaranteed to be faster than serial

connection. Depending on your system, serial connection

may provide faster and more stable communication. If

you were able to use serial connection with previous ver-

sions, we recommend that you continue using serial con-

nection.

• When using a serial connection, only COM ports 1–9 are

supported.

Console1

(CS1D)

PC1

Engine

(DSP1D)

Console2

(CS1D)

PC2

PC1

Engine

(DSP1D)

PC2

Engine

(DSP1D)

PC3

PC4

cascade

Console

(CS1D)

Console

(CS1D)

DSP1D

(ENGINE)

Master system Slave system

USB

RS-232-C

1. Serial connection

2. USB connection

D-sub 9-pin (male⇔male)

cross cable

Serial cable

USB cable

PC serial port

USB port

CS1D/DSP1D

rear panel

PM1D Manager V2 for Windows Owner’s Manual

Data communication method

Use the following procedure to initiate communication.

1. Connect your PC to the console or engine, using

either a serial connection or a USB connection.

Hint

When using USB connection, you must ﬁrst install the USB

driver. If you have not yet installed the USB driver, do so as

described in “USB driver installation” (→p.22).

2. Power-on the connected console/engine.

3. Start up PM1D Manager, and click the OPTION

button located in the lower left of the Function

menu screen or select [Manager Option] from the

[OPTION] menu in the menu bar.

4. In the Communication Port ﬁeld, select the port

that you will be using, and click the OK button.

When using a serial connection, only COM ports 1–9

are supported.

5. If the system includes a console, click the PERMIT

button in the PC CONNECTION area of the console’s

SYSTEM CONNECTION screen. This will allow a PC

connection with the connected console/engine.

For details, refer to “CS1D Reference Manual (Soft-

ware)” contained in the CS1D Owner’s Manual SYS/

W.CLOCK function.

Hint

•If you are using Mirror mode, you can communicate only

with the selected engine A or B. The PERMIT button for

the unused engine cannot be turned on from the PC

CONNECTION screen.

•If you are using Dual Console mode, you can communi-

cate only with console 1. The console 2 PERMIT button

will not appear in the PC CONNECTION screen.

Also, you cannot operate the various PERMIT buttons

from console 2.

•Only one PC can be connected to a system. It is not possi-

ble to connect multiple PC’s to a system. The PERMIT

button in the PC CONNECTION screen can be turned

on either (not both) for the console or the engine that is

being used (ENGINE A or B).

If you are using cascade connection, master and slave are

handled separately, so this is considered as two systems.

6. In the Function menu screen, click the ONLINE/

OFFLINE button.

The following popup window will appear.

In this popup window you can select one of the fol-

lowing two connection modes.

• UPLOAD

The current settings of PM1D Manager will be

transmitted to the console/engine, and then syn-

chronized operation will begin.

• DOWNLOAD

The current settings of the console/engine will be

transmitted to PM1D Manager, and then synchro-

nized operation will begin.

Whether PM1D Manager is online or ofﬂine can be

veriﬁed by the state of the ONLINE/OFFLINE but-

ton in the Function menu screen.

In a state in which it is not possible to initiate communica-

tions, the OFFLINE/ONLINE button will be grayed, and

cannot be clicked. In this case, please check the cable connec-

tions and settings.

When you click either UPLOAD or DOWNLOAD in the

“CONNECTION” popup window to select the connection

mode, please check the following points.

•In the console’s SYS/W.CLOCK screen PC CONNEC-

TION area, make sure that the PERMIT button of the

device connected to the PC is turned on.

•Make sure that no popup window is displayed in the

screen of the console.

•Make sure that no ﬁle is being loaded on the console.

•Make sure that time code is not running in the system.

•Auto fading or manual fading are not in progress.

If any of the above conditions are not satisﬁed, a popup

window will appear, informing you that the PC cannot be

connected to the other device, and the connection procedure

will be aborted at step 4 above.

Communication may become unstable if the cable is too

long. Use a cable no longer than 5 meters for serial connec-

tion, or a cable no longer than 3 meters for USB connection.

If time code is running when you attempt to initiate com-

munication, communication will be aborted. Transmit time

code after switching to online mode.

Click

Ofﬂine (connec-

tion not possible)

Ofﬂine (connec-

tion possible)

Online

Communication between PM1D Manager and the console/engine

Online operating procedure

If the console/engine and PC are connected correctly,

and communication is possible, the OFFLINE symbol

(see p.8) shown at the top of the PM1D Manager screen

will change to the ONLINE symbol, indicating that

PM1D Manager is online.

Now the PC and the entire system will be operate in tan-

dem, and you can use PM1D Manager for supplemen-

tary control of the system. However, some operations

and parameters will not be linked, so please read p.20

and 21 for details.

While an important operation is being performed on the

console, a popup window like the following will appear,

and PM1D Manager will be temporarily inoperable.

Please wait until the operation on the console has been

completed.

Ofﬂine operating procedure

To break communication between the online the con-

sole/engine and the PC, click the OFFLINE/ONLINE

button in the lower part of Function menu screen. The

following popup window will appear, so click the OK

button and you will switch to ofﬂine mode.

Immediately before PM1D Manager transitions from

ofﬂine to online, all data is automatically backed up. (This

is referred to as the recovery point.)

When returning to the ofﬂine state, the scene memories and

all library data will return to the recovery point, regardless

of the reason that the system went ofﬂine. In other words,

the current scene will be maintained from its online state,

but the scene memories and all library data will not be

maintained.

Also, the DIRECT RECALL / MIDI CTRL CHANGE / TC

EVENT functions will normally not be recovered. Be aware

that this may produce settings that you do not expect.

Even if the user does not manually switch to the ofﬂine

state, communication will forcibly be switched ofﬂine when

one of the following occurs.

• When you exit PM1D Manager while online

• When permission for PC connection is canceled on the

console

• When the console switches between engine A/B while the

PC is connected to the engine (system example 4 on p.10)

• When a console is connected to a system that consisted of

only an engine and a PC (system example 5 on p.10)

• When the cable connection is accidentally broken, or if a

communication time-out occurs for any reason (*)

• When processing cannot be performed in time because of

an excessive amount of data being transferred (*)

• When the user cancels during an upload or download (*)

• When the SYSTEM CONFIGURATION of the console is

switched to console 2 while the console and PC are still

online (*)

* In these cases, PM1D Manager will attempt to return

all data on the PC to the recovery point, but it is possi-

ble that the data has already been destroyed. You can

either reload the data, or re-connect to the device with

which you were communicating.

If the PC is connected to the engine in a system that

includes a console (system example 4 on p.10), and if

communication between the console and engine is bro-

ken for some reason, the scene memory and all library

data will return to the recovery point. If you are using

the PC as a backup for the console, we recommend that

you load the PC with same data as the console while the

PC is still ofﬂine, so that the recovery point will be the

same state as the console. Then make the connection.

Cautions regarding data communication

■ You should exit all Windows application software

and resident software. Communication may be

unstable if you fail to do so.

■ Do not perform the following operations while com-

munication is occurring. Doing so may cause com-

munication to be broken.

•Suspend/resume operations

• Starting up a screen saver (including automatic

startup by timer)

•Connecting or disconnecting a memory card or

USB device, etc.

■ If you are using a notebook PC, you may require a

higher level of performance than described for the

minimum level of system conﬁguration (→p.3).

■ If you are using a notebook PC, communication may

become unstable because of power-management set-

tings in the Windows control panel or power-man-

agement settings speciﬁc to your CPU (SpeedStep

[Intel CPUs], PowerNow! [AMD CPUs], LongRun

[Transmeta CPUs]). Please turn such functionality

off, and use the notebook PC with its AC power

adaptor connected.

PM1D Manager V2 for Windows Owner’s Manual

Remote Control functionality

If you connect PM1D Manager to a Yamaha digital mixer

(DM2000 V2, 02R96 V2, and DM1000 V2) via USB, you

will be able to use the digital mixer (subsequently

referred to as the “remote controller”) to remotely con-

trol the PM1D system.

• The digital mixers that can be used for remote control are

only the DM2000 V2, 02R96 V2, and DM1000 V2, and

each must be running system software V2. Remote con-

trol from other mixers is not possible.

•If you use a remote control device, the scene data and

setup data stored in the digital mixer (DM2000 V2,

02R96 V2, DM1000 V2) will be rewritten. Please back up

all of your digital mixer’s data to a computer or other

external media before you use the remote control func-

tions. For details on how to back up, refer to the manual

of your digital mixer.

• The PM1D system’s parameters that can be remotely con-

trolled are the HA GAIN or digital gain, ATT, EQ, GATE,

COMP, MIX SEND, FADER, ON, SURROUND, CUE/

SOLO ON, DCA, and scene parameters. For details, refer

to the remote control parameter list (→p.15).

•Parameters that do not match between the remote con-

troller and the PM1D will be controlled to the value that

is closest to the parameter value that was operated. This

means that the actual value may differ from the displayed

value.

Setup procedure

1. Make a USB or serial connection between the con-

sole/engine and the PC, and a USB connection

between the remote controller and the PC.

2. In the SETUP screen of the remote controller, go to

the MIDI/HOST page and set the Studio Manager

PORT to “USB” and the ID to “1.”

3. Start up PM1D Manager, and open the Option

popup window either by clicking the OPTION but-

ton in the lower left of the function menu screen or

by choosing [Manager Option] from the [Option]

menu in the menu bar.

4. In the Option window, make the port settings

shown below, and click [OK].

Communication Port: Select the port that you will

use to communicate with the console/engine.

Remote Control Setup: Select the USB input port

(IN PORT) and output port (OUT PORT) used to

communicate with the remote controller. If the con-

nection with the console/engine is also a USB con-

nection, be careful that you don’t select the console/

engine port by mistake.

5. From the menu bar, choose [Option] menu →

[Remote Control Setup] to open the REMOTE

CONTROL SETUP popup window.

6. In the REMOTE CONTROL SETUP window, select

the model name of the remote controller you’re

using in the REMOTE MACHINE ﬁeld.

7. In the REMOTE CONTROL SETUP window, make

channel assignments for the remote controller and

for the PM1D (→p.9).

8. In the function menu screen, click the REMOTE

ONLINE/OFFLINE button (or the RE-SYNCHRO-

NIZE button in the REMOTE CONTROL SETUP

windows) to enable Online status for communica-

tion with the remote controller.

9. In the function menu screen, click the ONLINE/

OFFLINE button to enable Online status for com-

munication with the console/engine.

This completes preparations for remote control.

10. In this state, operating the parameters on the

remote controller will also control the correspond-

ing parameters on the PM1D.

For details on the parameters supported for remote

control, refer to the remote control parameter list

(→p.15).

Yamaha digital mixer

(DM2000 V2, 02R96 V2,

DM1000 V2)

PM1D Manager

Console CS1D

Engine

DSP1D/DSP1D-EX

USB

USB/RS-232C

PM1D V2 system

Click

REMOTE ONLINE/

OFFLINE button

ONLINE/

OFFLINE button

Remote Control functionality

Remote control parameter list

PM1D

Direction

Remote Controller

Parameter Parameter Notes

Input Fader ↔ Input Fader

Input On ↔ Input On

Input Att ↔

Input Att

When ATT mode = ATT

Input HA Gain ↔ When ATT mode = HA GAIN

Input EQ

---- Ignored ←

Input EQ

EQ TYPE

---- Ignored ←

Low Q

When HPF

Low L.SHELF ↔ When L.SHELF

Low Q ↔ When other than L.SHELF or HPF

HPF F ↔

Low F

When IN EQ LOW = HPF

Low F ↔ When IN EQ LOW = LOW

Low G ↔ Low G When IN EQ LOW = LOW

HPF on ↔ Low G (HPF On) When IN EQ LOW = HPF

Low Mid Q ↔ Low Mid Q

Low Mid F ↔ Low Mid F

Low Mid G ↔ Low Mid G

Hi Mid Q ↔ Hi Mid Q

Hi Mid F ↔ Hi Mid F

Hi Mid G ↔ Hi Mid G

Hi LPF ↔

Hi Q

When LPF

Hi H.SHELF ↔ When H.SHELF

Hi Q ↔ When other than H.SHELF or LPF

Hi F ↔ Hi Mid F

Hi G ↔ Hi Mid G

Hi LPF Ignored ← LPF On

On ↔ On

Input Gate

On ↔

Input Gate

----

Ignored ← Link

Ignored ← KeyIn

Ignored ← KeyAUX

Ignored ← KeyCh

Type ↔ Type

Attack ↔ Attack

Range ↔ Range

Hold ↔ Hold

Decay ↔ Decay

Threshold ↔ Threshold

Input Comp

---- Ignored ←

Input Comp

LocComp

On ↔ On

---- Ignored ← Link

Type ↔ Type

Attack ↔ Attack

Release ↔ Release

Ratio ↔ Ratio

Gain ↔ Gain

Knee ↔ Knee

Threshold ↔ Threshold

Input Surround

---- Ignored ←

Input Surround

Direction

Link ↔ Link

Pattern Link ↔ PattLink

Surround LFE ↔ LFE

Divergence F ↔ Div

LR Pan ↔ X

FR Pan ↔ Y

---- Ignored ← Width

---- Ignored ← Depth

---- Ignored ← OffsetX

---- Ignored ← OffsetY

Divergence Link ↔ DivLink

Divergence R ↔ DivRear

PM1D Manager V2 for Windows Owner’s Manual

Input to Stereo Pan ↔ Input Channel Pan

Input to Stereo On ↔ Routing Stereo

Mix Send

On ↔

Aux Send

On to aux1–12

Pre/Post ↔ Pre/Post to aux1–12

Level ↔ Level to aux1–12

Pan (only if mix

pair)

↔ Aux Pan (only if aux pair) to aux1/2–11/12

Mix Fader ↔ Aux Fader

Mix On ↔ Aux On

Mix EQ

---- Ignored ← Aux EQ EQ TYPE

SubLow HPF ↔

Low Q

When HPF

SubLow L.SHELF ↔

When L.SHELF

SubLow Q ↔ When other than L.SHELF or HPF

SubLow F ↔ Low F

SubLow G ↔ Low G

---- Ignored ← HPF On

SubLow On → Ignored ----

Low Q ↔ Low Mid Q

Low F ↔ Low Mid F

Low G ↔ Low Mid G

Low On → Ignored ----

Low Mid Q ↔ Hi Mid Q

Low Mid F ↔ Hi Mid F

Low Mid G ↔ Hi Mid G

Low Mid On → Ignored ----

Mid Q ↔ ----

Mid F ↔ ----

Mid G ↔ ----

Mid On → Ignored ----

Hi Mid Q ↔ ----

Hi Mid F ↔ ----

Hi Mid G ↔ ----

Hi Mid On → Ignored ----

Hi LPF ↔

Hi Q

When LPF

Hi H.SHELF ↔

When H.SHELF

Hi Q ↔ When other than H.SHELF or LPF

Hi F ↔ Hi Mid F

Hi G ↔ Hi Mid G

---- Ignored ← LPF On

Hi On → Ignored ----

On ↔ On

Mix Comp

---- Ignored ←

Aux Comp

LocComp

On ↔ On

---- Ignored ← Link

Type ↔ Type

Attack ↔ Attack

Release ↔ Release

Ratio ↔ Ratio

Gain ↔ Gain

Knee ↔ Knee

Threshold ↔ Threshold

Matrix Fader ↔ Bus Fader

Matrix On ↔ Bus On

PM1D

Direction

Remote Controller

Parameter Parameter Notes

High mode

Low mode

Remote Control functionality

Matrix EQ

---- Ignored ← Bus EQ EQ TYPE

SubLow HPF ↔

Low Q

When HPF

SubLow L.SHELF ↔

When L.SHELF

SubLow Q ↔ When other than L.SHELF or HPF

SubLow F ↔ Low F

SubLow G ↔ Low G

SubLow HPF Ignored ← HPF On

SubLow On → Ignored ----

Low Q → Ignored Low Mid Q

Low F → Ignored Low Mid F

Low G → Ignored Low Mid G

Low On → Ignored ----

Low Mid Q ↔ Hi Mid Q

Low Mid F ↔ Hi Mid F

Low Mid G ↔ Hi Mid G

Low Mid On → Ignored ----

Mid Q → Ignored ----

Mid F → Ignored ----

Mid G → Ignored ----

Mid On → Ignored ----

Hi Mid Q ↔ ----

Hi Mid F ↔ ----

Hi Mid G ↔ ----

Hi Mid On → Ignored ----

Hi LPF ↔

Hi Q

When LPF

Hi H.SHELF ↔

When H.SHELF

Hi Q ↔ When other than H.SHELF or LPF

Hi F ↔ Hi Mid F

Hi G ↔ Hi Mid G

Hi LPF Ignored ← LPF On

Hi On → Ignored ----

On ↔ On

Matrix Comp

---- Ignored ←

Bus Comp

LocComp

On ↔ On

---- Ignored ← Link

Type ↔ Type

Attack ↔ Attack

Release ↔ Release

Ratio ↔ Ratio

Gain ↔ Gain

Knee ↔ Knee

Threshold ↔ Threshold

Stereo Fader ↔ Stereo Fader

Stereo Bal ↔ Stereo Bal

Stereo On ↔ Stereo On

PM1D

Direction

Remote Controller

Parameter Parameter Notes

High mode

Low mode

PM1D Manager V2 for Windows Owner’s Manual

Stereo EQ

---- Ignored ← Stereo EQ EQ TYPE

SubLow HPF ↔

Low Q

When HPF

SubLow L.SHELF ↔

When L.SHELF

SubLow Q ↔ When other than L.SHELF or HPF

SubLow F ↔ Low F

SubLow G ↔ Low G

SubLow HPF Ignored ← HPF On

SubLow On → Ignored ----

Low Q → Ignored Low Mid Q

Low F → Ignored Low Mid F

Low G → Ignored Low Mid G

Low On → Ignored ----

Low Mid Q ↔ Hi Mid Q

Low Mid F ↔ Hi Mid F

Low Mid G ↔ Hi Mid G

Low Mid On → Ignored ----

Mid Q → Ignored ----

Mid F → Ignored ----

Mid G → Ignored ----

Mid On → Ignored ----

Hi Mid Q ↔ ----

Hi Mid F ↔ ----

Hi Mid G ↔ ----

Hi Mid On → Ignored ----

Hi LPF ↔

Hi Q

When LPF

Hi H.SHELF ↔

When H.SHELF

Hi Q ↔ When other than H.SHELF or LPF

Hi F ↔ Hi Mid F

Hi G ↔ Hi Mid G

Hi LPF Ignored ← LPF On

Hi On → Ignored ----

On ↔ On

Stereo Comp

---- Ignored ←

Stereo Comp

LocComp

On ↔ On

---- Ignored ← Link

Type ↔ Type

Attack ↔ Attack

Release ↔ Release

Ratio ↔ Ratio

Gain ↔ Gain

Knee ↔ Knee

Threshold ↔ Threshold

Input Pair ↔ Input Pair

Mix Pair ↔ Aux Pair

Matrix Pair ↔ Bus Pair

Word Clock status Ignored ← Word Clock select Specify 48k if PM1D is unlocked

Input CH Select ↔ Input CH Select

Output CH select ↔

Aux CH select

Bus CH select

Stereo select

Input Cue ↔ Input Solo

Mix Cue ↔ Aux Solo

Matrix Cue ↔ Bus Solo

Stereo Cue ↔ Stereo Solo

Cue mode ↔ Solo Sel mode

Cue Interruption ↔ Solo Interruption

DCA Fader 1-8 ↔ Input Fader Group Fader

DCA Fader 9-12 ↔ Output Fader Group Fader

DCA Mute 1-8 ↔ Input Fader Group On

DCA Mute 9-12 ↔ Output Fader Group On

Mute Master 1-8 ↔ Input Mute Master

PM1D

Direction

Remote Controller

Parameter Parameter Notes

High mode

Low mode

Remote Control functionality

*1. Indicates the direction(s) in which remote control is supported.

↔ .................... Commands can be transmitted and received in either direction between the PM1D and the remote controller.

Ignored ← ...... This is a parameter not found on the PM1D, so the command will be ignored if it is received from the remote controller.

→ Ignored ...... This is a parameter not found on the remote controller, so the command will be ignored if it is received from the PM1D.

*2. AUX channels on units other than the DM2000 V2 are 1–8. The corresponding MIX channels will depend on the MIX ASSIGN settings in the

REMOTE CONTROL SETUP popup window.

*3. Since the PM1D does not have column 9–column 16, the data is ﬁxed as “ ” (space) on the remote controller.

Mute Master 9-12 ↔ Output Mute Master

Surround Mode ↔ Surround Mode

Input CH Name (Short) ↔ Input CH Name (Short) column1–4

Input CH Name (Long) ↔ Input CH Name (Long)

column1–8

column9–16

Mix CH Name (Short) ↔ Aux CH Name (Short) column1–4

Mix CH Name (Long) ↔ Aux CH Name (Long)

column1–8

column9–16

Matrix CH Name (Short) ↔ Bus CH Name (Short) column1–4

Matrix CH Name (Long) ↔ Bus CH Name (Long)

column1–8

column9–16

Stereo CH Name (Short) L-side only ↔ Stereo CH Name (Short) column1–4

Stereo CH Name (Long) L-side only ↔ Stereo CH Name (Long)

column1–8

column9–16

Scene Now # ↔ Scene Now

Scene Last # ↔ Scene Last

Scene Recall Function ← Scene Recall Function

Scene Clear Function ↔ Scene Clear Function

Scene Store Function ↔ Scene Store Function

Scene Title ↔ Scene Title

Scene Protect ↔ Scene Protect

PM1D

Direction

Remote Controller

Parameter Parameter Notes

PM1D Manager V2 for Windows Owner’s Manual

Special considerations

This section notes various things you should be aware of concerning the parameters and operations in each

screen.

■ PREFERENCE switch

■ SELECTED INPUT CHANNEL / SELECTED

OUTPUT CHANNEL

These settings are not linked with the console in the

system, and can be set independently.

Hint

Yo u can switch the channel directly by left-clicking or right-

clicking SELECTED INPUT CHANNEL / SELECTED

OUTPUT CHANNEL ﬁeld located in the lower part of the

screen.

■ MODULE FLIP / FADER FLIP

These functions are speciﬁc to the console, and do

not exist in PM1D Manager.

■ PREVIEW mode on/off (MEMORY screen)

This is not linked with the console in the system, and

can be set independently.

If you exit PM1D Manager with Preview mode turned

on, the content (Preview mode content) that was dis-

played when you last exited) will be recovered. However

at this time, the PREVIEW button will be turned off. In

the same way if you go ofﬂine with Preview mode

turned on, the contents that had been Preview-dis-

played when online will be handled as Preview mode =

off.

■ Fade time operation

Due to functional limitations, realtime control and

monitoring of the fade time is not possible on PM1D

Manager. Thus, the manual fade function cannot be

used.

If you recall a scene for which a fade time setting has

been speciﬁed, the faders/pan in PM1D Manager will

immediately indicate the value that is to be reached

after fading, and will stop there. However, if you

operate a fader while the fade time is being executed,

the fade for that channel will be cancelled, and the

fader will remain at the position to which you moved

it.

If the PC and engine alone are online, Fader Start

control is performed from PM1D Manager. Thus,

even if the scene has a fader time setting, Fader Start

will function immediately after scene recall occurs.

■ MIDI program changes / control changes

The MIDI ports of the PC cannot be used as MIDI

inputs/outputs for the PM1D Manager software.

■ TC events

The setting can always be made, but since operation

in response to incoming time code is performed by

the console itself, the following restrictions apply.

(*) It will not be possible to operate the EVENT RECALL-

ING button or TIME CODE IN button in the TC

EVENT screen (MIDI/GPI/TC function).

It is not possible to output time code directly from the

PC. Nor can the CAPTURE button operated from the

PC.

■ Meters

The function of the meters will change as follows,

depending on the online/ofﬂine status of PM1D

Manager, and on the presence or absence of a con-

sole.

(*) Due to functional limitations, some meter data can be

displayed only for a single selected channel within the

system. In such cases, the channel selected on the con-

sole will be given priority.

In order to avoid inconsistencies due to the fact that

the selected channel is not linked between the PC and

console, this type of meter will not be displayed on the

PC.

Also, the ∑ meter will not be displayed on the PC.

CONFIRMATION

ON/OFF

These settings are not linked

with the console in the system,

and therefore must be set indi-

vidually.

WARNING MESSAGES

ON/OFF

GATE/COMP GR

METER ON/OFF LINK

INTERNAL

CALENDAR/CLOCK

Since this indicates the date of

the PC, it is not linked with the

console. Make this setting in

the Windows [Control Panel]-

[Date and time].

Others

These functions are speciﬁc to

the console, and do not exist in

PM1D Manager.

The SELECTED CH ﬁeld in the

AUTO DISPLAY area is not

shown in PM1D Manager, but

is always enabled.

Ofﬂine

Fixed at Preview mode = off

Online

Preview mode can be turned

on/off

Ofﬂine

Function is valid (*)

Online

Console exists in

the system

Function is valid

Console does not

exist in the system

Function is invalid (*)

Ofﬂine

No meters will be dis-

played.

Online

Console exists in

the system

Some meters will not

be displayed. (*)

Console does not

exist in the system

All meters will be dis-

played.

Страница загружается...

Yamaha PM1D, V2 Инструкция по применению

Похожие модели бренда