YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Malaysia ID
V624940
RX-V800RDS
Natural Sound AV Receiver
Ampli-tuner audio-vidéo
G B
RX-V800RDS
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
0100V800RDS(GB)-cv1/4 8/29/0, 10:02 AM1
II
II
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this unit in a well ventilated, cool, dry, clean
place with at least 30 cm on the top, 20 cm on the
right and left, and 10 cm at the back of this unit
— away from direct sunlight, heat sources,
vibration, dust, moisture, and/or cold.
3 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds. To prevent fire or electrical
shock, do not place this unit where it may get
exposed to rain, water, and/or any type of liquid.
4 Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this
unit in a environment with high humidity (i.e. a room
with a humidifier) to prevent condensation inside
this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5 On the top of this unit, do not place:
– Other components, as they may cause damage
and/or discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may cause
electrical shock to the user and/or damage to this
unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation.
If the temperature inside this unit rises, it may
cause fire, damage to this unit, and/or personal
injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified
is dangerous and may cause fire, damage to this
unit, and/or personal injury. YAMAHA will not be
held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, disconnect the
power cord from the wall outlet during an electrical
storm.
14 Take care of this unit so that no foreign objects and/
or liquid drops inside this unit.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
15 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
16 When not planning to use this unit for long periods
of time (i.e. vacation), disconnect the AC power plug
from the wall outlet.
17 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
18 Before moving this unit, press STANDBY/ON to set
this unit in the standby mode, and disconnect the
AC power plug from the wall outlet.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet,
even if this unit itself is turned off. This state is called
the standby mode. In this state, this unit is designed to
consume a very small quantity of power.
■ For U.K. customers
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
Note
• The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
■ Special Instructions for U.K.
Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED
IN ACCORDANCE WITH THE FOLLOWING
CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured BLUE must be connected
to the terminal which is marked with the letter N or
coloured BLACK. The wire which is coloured
BROWN must be connected to the terminal which is
marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
CAUTION
1
English
INTRODUCTION
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTENTS
INTRODUCTION
INTRODUCTION
CONTENTS ........................................................... 1
FEATURES ............................................................ 2
GETTING STARTED ........................................... 3
Checking the Package Contents ............................... 3
Installing Batteries in the Remote Control ............... 3
CONTROLS AND FUNCTIONS ........................ 4
Front Panel ............................................................... 4
Remote Control ........................................................ 6
Description of the Numeric Buttons......................... 7
Using the Remote Control ........................................ 8
Front Panel Display .................................................. 9
Rear Panel .............................................................. 10
PREPARATION
SPEAKER SETUP .............................................. 11
Speakers to Be Used ............................................... 11
Speaker Placement ................................................. 11
CONNECTIONS ................................................. 12
Before Connecting Components ............................ 12
Connecting Audio Components ............................. 12
Connecting Video Components .............................. 14
Connecting the Speakers ........................................ 16
Connecting to an External Amplifier ..................... 18
Connecting an External Decoder ............................ 18
IMPEDANCE SELECTOR Switch ....................... 19
Connecting the Power Supply Cords ...................... 19
ON-SCREEN DISPLAY (OSD) ......................... 20
OSD Modes ............................................................ 20
Selecting the OSD Mode ........................................ 20
SPEAKER MODE SETTINGS ......................... 21
Summary of SPEAKER SET Items
1A through 1E .................................................... 21
ADJUSTING THE SPEAKER
OUTPUT LEVELS ......................................... 22
Before You Begin ................................................... 22
Using the Test Tone (TEST DOLBY SUR.) .......... 22
BASIC OPERATION
BASIC PLAYBACK ............................................ 24
Input Modes and Indications .................................. 26
Selecting a Sound Field Program ........................... 28
Normal Stereo Reproduction .................................. 29
TUNING ............................................................... 30
Connecting the Antennas ........................................ 30
Automatic (or Manual) Tuning .............................. 31
Presetting Stations .................................................. 32
Tuning in to a Preset Station .................................. 33
Exchanging Preset Stations .................................... 34
RECEIVING RDS STATIONS .......................... 35
Description of RDS Data ........................................ 35
Changing the RDS Mode ....................................... 35
PTY SEEK Function .............................................. 36
EON Function ........................................................ 37
BASIC RECORDING ......................................... 38
ADVANCED OPERATION
SET MENU .......................................................... 39
Adjusting the Items on the SET MENU................. 39
1 SPEAKER SET (speaker mode settings) ........... 40
2 LOW FRQ TEST ............................................... 42
3 L/R BALANCE (balance of the
left and right main speakers) .............................. 43
4 HP TONE CTRL (headphone tone control) ....... 43
5 CENTER GEQ (center graphic equalizer) ......... 43
6 INPUT RENAME .............................................. 44
7 I/O ASSIGNMENT ............................................ 44
8 INPUT MODE (initial input mode) ................... 44
9 PARAM. INI (parameter initialization) ............. 44
10 DOLBY D. SET (Dolby Digital set) ............... 45
11 DTS LFE LEVEL ............................................ 45
12 6.1/ES AUTO ................................................... 45
13 SP DELAY TIME ............................................ 46
14 DISPLAY SET ................................................. 46
15 MEMORY GUARD ......................................... 46
ADJUSTING THE LEVEL OF THE EFFECT
SPEAKERS ...................................................... 47
SLEEP TIMER .................................................... 48
Setting the Sleep Timer .......................................... 48
Canceling the Sleep Timer ..................................... 48
REMOTE CONTROL FEATURES .................. 49
Selector Dial ........................................................... 49
Commonly Used Buttons in Any Position of the
Selector Dial ....................................................... 50
Controlling the Components
Connected to This Unit ...................................... 50
Button Names and Functions in Each Position ...... 51
Setting the Manufacturer Code .............................. 54
Programming a New Remote Control Function
(Learn Feature) ................................................... 55
Returning to the Factory Setting ............................ 56
ADDITIONAL INFORMATION
SOUND FIELD PROGRAM ............................. 57
Hi-Fi DSP Programs ............................................... 57
CINEMA DSP Programs ....................................... 58
MOVIE THEATER Programs ................................ 61
SOUND FIELD PROGRAM PARAMETER
EDITING ......................................................... 62
What is a sound field? ............................................ 62
Sound Field Program Parameters ........................... 62
Changing Parameter Settings ................................. 63
Resetting a Parameter to the Factory-set Value ...... 63
Digital Sound Field Parameter Descriptions .......... 64
APPENDIX
TROUBLESHOOTING ...................................... 68
SPECIFICATIONS ............................................. 73
2
Thank you for selecting this YAMAHA AV receiver.
FEATURES
Other Features
◆ 96-kHz/24-bit D/A Converter
◆ “SET MENU” which Provides You with 15 Items
for Optimizing This Unit for Your Audio/Video
System
◆ Test Tone Generator for Easier Speaker Balance
Adjustment
◆ 6-Channel External Decoder Input for Other
Future Formats
◆ BASS EXTENSION Button for Reinforcing
Bass Response
◆ On Screen Display Function Helpful in
Controlling This Unit
◆ S Video Signal Input/Output Capability
◆ Component Video Input/Output Capability
◆ Optical and Coaxial Digital Audio Signal Jacks
◆ Sleep Timer
◆ Remote Control with Preset Manufacturer Codes
and “Learning” Capability
• y indicates a tip for your operation.
• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button
names differ between the main unit and the remote control, the button name on the remote control is given in parentheses in this
manual.
Built-in 5-Channel Power Amplifier
◆ Minimum RMS Output Power
(0.04% THD, 20 Hz – 20 kHz)
Main: 100 W + 100 W (8 Ω)
Center: 100 W (8 Ω)
Rear: 100 W + 100 W (8 Ω)
Multi-Mode Digital Sound Field
Processing
◆ Digital Sound Field Processor (DSP)
◆ Dolby Pro Logic Decoder
◆ Dolby Digital/Dolby Digital Matrix 6.1 Decoder
◆ DTS/DTS ES Decoder
◆ CINEMA DSP: Combination of YAMAHA DSP
Technology and Dolby Pro Logic, Dolby Digital
or DTS
◆ Virtual CINEMA DSP
◆ SILENT CINEMA DSP
Sophisticated AM/FM Tuner
◆ 40-Station Random Access Preset Tuning
◆ Automatic Preset Tuning
◆ Preset Station Shifting Capability (Preset
Editing)
◆ Multi-Functions for RDS Broadcast Reception
Manufactured under license from Dolby Laboratories.
“Dolby”, “AC-3”, “Pro Logic”, “Surround EX” and the double-D
symbol are trademarks of Dolby Laboratories.
Confidential Unpublished Works. ©1992-1997 Dolby
Laboratories, Inc. All rights reserved.
Manufactured under license from Digital Theater Systems, Inc.
US Pat. No. 5,451,942 and other world-wide patents issued and
pending. “DTS”, “DTS Digital Surround” and “DTS ES” are
trademarks of Digital Theater Systems, Inc. Copyright 1996
Digital Theater Systems, Inc. All Rights Reserved.
3
English
INTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
Remote control
Installing Batteries in the Remote
Control
Insert the batteries in the correct direction by aligning the
+ and – marks on the batteries with the polarity markings
(+ and –) inside the battery compartment.
■ Notes on batteries
• Change the batteries periodically.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline
and manganese batteries) together. Read the packaging
carefully as these different types of batteries may have
the same shape and color.
GETTING STARTED
Checking the Package Contents
Check your package to make sure it has the following items.
Manganese batteries (4)
(AAA, R03, UM-4)
Indoor FM antenna
AM loop antenna
Quick Reference Card
■ Changing batteries
As the batteries lose power, the operating range of the
remote control decreases and the indicator does not flash
or its light becomes dim. When you notice any of these
conditions, change all of the batteries.
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the manufacturer code and program
any acquired functions that may have been cleared.
Note
• If the batteries have leaked, dispose of them immediately.
Avoid touching the leaked material or letting it come into
contact with clothing, etc. Clean the battery compartment
thoroughly before installing new batteries.
1
2
3
A/B/C/D/E
Quick Reference Card
75-ohm/300-ohm
antenna adapter
(U.K. model only)
4
CONTROLS AND FUNCTIONS
Front Panel
1 STANDBY/ON
Turns on and sets this unit in the standby mode. When
you turn on this unit, you will hear a click and there will
be a 4 to 5-second delay before this unit can reproduce
sound.
Standby mode
In this mode, this unit consumes a small amount of
power to receive infrared-signals from the remote
control.
2 Remote control sensor
Receives signals from the remote control.
3 Front panel display
Shows information about the operational status of this
unit (see page 9).
4 INPUT MODE
Selects the mode of input for sources that send two or
more types of signals to this unit (see page 26).
You cannot control the input mode when you select 6CH
INPUT as the input source.
5 INPUT l / h
Selects the input source (DVD, D-TV/LD, CBL/SAT,
VCR 1, VCR 2/DVR, V-AUX, PHONO, CD, TUNER,
CD-R, MD/TAPE) you want to listen to or watch.
6 VOLUME
Controls the output level of all audio channels.
This does not affect the REC OUT level.
7 6CH INPUT
Selects the source connected to the 6CH INPUT jacks.
The source selected by pressing 6CH INPUT takes
priority over the source selected with INPUT l / h (or
the input selector buttons).
8 SPEAKERS A/B
Turn on or off the set of main speakers connected to the A
and/or B terminals on the rear panel.
9 BASS EXTENSION ON/OFF
When pushed in (ON), this feature boosts the bass
frequency of the left and right main channels by +6 dB
(60 Hz) while maintaining overall tonal balance. This
boost is useful if you do not use a subwoofer.
However, this boost may not be noticeable if “1B MAIN
SP” on the SET MENU is set to SMALL and “1D LFE/
BASS OUT” is set to SWFR.
0 PROCESSOR DIRECT ON/OFF
When pushed in (ON), BASS, TREBLE, and BASS
EXTENSION are bypassed, eliminating any alteration of
the original signal.
A/B/C/D/E
SPEAKERS
STANDBY
/ON
AB
BASS
EXTENSION
PROCESSOR
DIRECT
PRESET/
TUNING
BASS
6CH INPUT
VOLUME
INPUT
INPUT MODE
–
+
TREBLE
–
+
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
RDS MODE
/FREQ
EON PTY SEEK
MODE
START
FM/AM
PHONES S VIDEO VIDEO
L AUDIO R OPTICAL
SILENT
VIDEO AUX
EFFECT
PROGRAM
ON OFF
SURROUND
DIGITAL
DIGITAL
TUNER
DSP
1
2
34
56
7
89 0
qw
e
r
ty
h
g
PRESET
/TUNING
EDIT
MEMORY
MAN'L/AUTO FM
TUNING
MODE
AUTO/MAN'L MONO
RDS MODE
/FREQ
EON PTY SEEK
MODE
START
FM/AM
iopa
sdf
u
5
English
INTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
a RDS MODE/FREQ
When an RDS station is received, press this button to
change the display mode among the PS mode, PTY mode,
RT mode, CT mode (if the station offers those RDS data
services) and/or frequency display mode in turn.
s EON
Press this button to select the desired program type
(NEWS, INFO, AFFAIRS, SPORT) when you want to
tune in to a radio program of that type automatically.
d PTY SEEK MODE
Press this button to set the unit in the PTY SEEK mode.
f PTY SEEK START
Press this button to begin searching for a station after the
desired program type has been selected in the PTY SEEK
mode.
g BASS
Adjusts the low-frequency response for the left and right
main channels.
Turn the control to the right to increase or to the left to
decrease the low-frequency response.
h TREBLE
Adjusts the high-frequency response for the left and right
main channels.
Turn the control to the right to increase or to the left to
decrease the high-frequency response.
Note
• If you increase or decrease the high-frequency or the low-
frequency sound to an extreme level, the tonal quality from the
center and rear speakers may not match that of the left and
right main speakers.
■ Opening and closing the front
panel door
When you are not operating the controls behind the front
panel door, close the door.
D
I
G
I
T
A
L
q EFFECT
Switches the effect speakers (center and rear) on and off.
If you turn off the output of these speakers by using
EFFECT, all Dolby Digital and DTS audio signals except
for the LFE channel are directed to the main left and right
channels.
When Dolby Digital or DTS signals are mixed, the left
and right main channel signal levels may not match.
w A/B/C/D/E
Selects one of the 5 preset station groups (A to E).
e PROGRAM l / h
Selects the DSP program (see page 28).
r PRESET/TUNING l / h
Selects preset station number 1 to 8 when the colon (:)
appears next to the band indication on the front panel
display, and selects the tuning frequency when the colon
(:) does not appear.
t PHONES jack
Outputs audio signals for private listening with
headphones. When you connect headphones, no signals
are output to the OUTPUT jacks or to the speakers.
y VIDEO AUX jacks
Inputs audio and video signals from a portable external
source such as a game console. To reproduce source
signals from these jacks, select V-AUX as the input
source.
u PRESET/TUNING (EDIT)
Switches the function of PRESET/TUNING l / h (the
colon (:) turns on or off) between selecting a preset
station number and tuning.
This button is also used to exchange the assignment of
two preset stations with each other.
i FM/AM
Switches the reception band between FM and AM.
o MEMORY (MAN’L/AUTO FM)
Stores a station in the memory. Hold down this button for
more than 3 seconds to start automatic preset tuning.
p TUNING MODE (AUTO/MAN’L MONO)
Switches the tuning mode between automatic and manual.
To select the automatic tuning mode, press this button so
that the “AUTO” indicator lights up on the front panel
display. To select the manual tuning mode, press this
button so that the “AUTO” indicator does not light up.
To open, press gently on the lower part of the panel.
6
CONTROLS AND FUNCTIONS
A/B/C/D/E
TV INPUT
TV VOLUME
TV POWER
EFFECT
w
e
1
2
3
4
5
6
7
8
0
q
9
r
t
y
u
i
Remote Control
This section describes the basic operation of this unit with
the remote control. First, set the selector dial to the AMP/
TUN position. See “REMOTE CONTROL FEATURES”
on pages 49 to 56 for full details.
Select the
AMP/TUN
position.
See page 7.
1 DSP
Switches the function of the numeric buttons to the DSP
program selector (see page 7).
2 Indicator window
Shows the name of components which can be controlled.
3 Numeric buttons (Input selector buttons)
These buttons select the input source.
See pages 7 and 8 for the numeric buttons.
4 TEST
Outputs the test tone.
5 ON SCREEN
Selects the on-screen display (OSD) mode for your video
monitor.
6 j / i
Adjust DSP program parameters and SET MENU items.
7 LEVEL
Selects the effect speaker channel (center, rear and
subwoofer) so you can adjust their output level
independently.
8 SLEEP
Sets the sleep timer.
9 INPUT
Switches the function of the numeric buttons to the input
selector (see page 7).
0 Indicator
Flashes while the remote control is sending signals.
q Selector dial
Turn this dial to select the position for the component to
be controlled. (The proper code must be set up for your
component. See “Setting the Manufacture Codes” on
page 54.) When the position is selected, the remote
control is set to that component operation mode.
w A/B/C/D/E, PRESET–/+
These buttons are used to select a preset station.
A/B/C/D/E: To select one of 5 preset station groups (A
to E)
PRESET –/+: To select a preset station number (1 to 8)
e u/d
Select DSP program parameters and SET MENU items.
r SET MENU
Enters the SET MENU.
t POWER
Turns on the power of this unit.
y STANDBY
Sets this unit in the standby mode.
7
English
INTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
A B
u VOLUME +/–
Increases or decreases the volume level.
i MUTE
Mutes the sound. Press again to restore the audio output
to the previous volume level.
EFFECT
Switches the effect speakers (center and rear) on and off
in the following cases:
• When the selector dial is set to the DSP/TUN position.
• While the indicator is lit for about 3 seconds after
pressing DSP.
Description of the Numeric
Buttons
The numeric buttons function in various ways depending
on the position of the selector dial or the combination of
other instructions.
■ When selecting an input source
Input selector
buttons
1 Press INPUT regardless of the position of
the selector dial.
The indicator lights up for about 3 seconds.
2 You can select an input source with the
numeric buttons while the indicator is lit.
■ When selecting a DSP program
and turning on or off the effect
speakers (center and rear)
DSP program
group buttons
A
1 Press DSP regardless of the position of the
selector dial.
The indicator lights up for about 3 seconds.
2 You can select a DSP program with the
numeric buttons, turn on or off the effect
speakers (center and rear) by pressing
EFFECT and turn on or off the Dolby Digital
Matrix 6.1 or DTS ES decoder by pressing
6.1/ES while the indicator is lit.
B
1 Set the selector dial to the DSP/TUN
position.
2 You can select a DSP program directly with
the numeric buttons, turn on or off the effect
speakers (center and rear) by pressing
EFFECT and turn on or off the Dolby Digital
Matrix 6.1 or DTS ES decoder by pressing
6.1/ES.
8
CONTROLS AND FUNCTIONS
STANDBY
/ON
–
+
–
+
SURROUND
DIGITAL
DIGITAL
TUNER
DSP
30° 30°
■ When selecting a preset station
number
1 Set code number “0023” in the AMP/TUN (or
DSP/TUN) position.
See page 54 for setting the code.
2 Set the selector dial to the AMP/TUN (or
DSP/TUN) position.
3 You can select a preset station number
directly with the numeric buttons (1 to 8).
See page 34.
Using the Remote Control
Approximately 6 m (20 feet)
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.
■ Handling the remote control
• Do not spill water or other liquids on the remote
control.
• Do not drop the remote control.
• Do not leave or store the remote control in the
following types of conditions:
– high humidity or temperature such as near a heater,
stove or bath;
– dusty places; or
– in places subject to extremely low temperatures.
9
English
INTRODUCTION PREPARATION
BASIC
OPERAIONT
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONTROLS AND FUNCTIONS
DIGITAL
DTS MOVIE THEATER 1
2
DOLBY DIGITAL
PRO LOGIC ENTERTAINMENT
DSP
6.1/ES
PCM
PRO LOGIC
A
SP
B
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
VIRTUAL
PS
PTY
RT
CT
PTY
HOLD
EON
STEREO
AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
VOLUME
dB
ms
SLEEP
1 234 wq87
apio
6
uyre t
09 5
Front Panel Display
1 t indicator
Lights up when the built-in DTS decoder is on.
2 VIRTUAL indicator
Lights up when using Virtual CINEMA DSP (see
page 29).
3 g and o indicators
Light up according to the type of Dolby signals this unit
is reproducing. “ g ” lights up when the built-
in Dolby Digital decoder is on. “ o ” lights up
when the built-in Dolby Pro Logic decoder is on.
4 x indicator
Lights up when you select a DSP program.
5 DSP program indicators
The name of the selected DSP program lights up when
the ENTERTAINMENT, MOVIE THEATER 1, MOVIE
THEATER 2 or q/DTS SURROUND DSP program is
selected.
6 PTY HOLD indicator
Lights up while searching for stations in the PTY SEEK
mode.
7 RDS mode indicators
The name(s) of the RDS data offered by the currently
received RDS station light(s) up. Illumination of the red
indicator next to the RDS data name shows that the
corresponding RDS mode is now selected.
8 EON indicator
Lights up when an RDS station that offers the EON data
service is being received.
9 STEREO indicator
Lights up when the unit is receiving a strong signal for an
FM stereo broadcast while the “AUTO” indicator is lit.
0 AUTO indicator
Shows that this unit is in the automatic tuning mode.
q VOLUME level indicator
Indicates the volume level.
w Input source indicator
Shows the current input source with the arrow-shaped
cursor.
e c indicator
Lights up when the built-in Dolby Digital Matrix 6.1 or
DTS ES decoder is on.
r v indicator
Lights up when this unit is reproducing PCM (pulse code
modulation) digital audio signals.
t SP A/B indicator
Lights up according to which set of main speakers is
selected. Both indicators light up when both sets of
speakers are selected.
y Headphones indicator
Lights up when headphones are connected.
u Multi-information display
Shows the current DSP program name and other
information when adjusting or changing settings.
i MEMORY indicator
Flashes to show a station can be stored.
o Program type name indicators
The name of the selected program type lights up when the
“EON” indicator lights up.
p TUNED indicator
Lights up when this unit tunes in to a station.
a SLEEP indicator
Lights up while the sleep timer is on.
10
CONTROLS AND FUNCTIONS
(Europe model)
Rear Panel
1 DIGITAL INPUT jacks
2 DIGITAL OUTPUT jacks
3 Antenna input terminals
See page 30 for connection information.
4 Audio component jacks
See pages 12 and 13 for connection information.
5 Video component jacks
See pages 14 and 15 for connection information.
6 Speaker terminals
See pages 16 and 17 for connection information.
7 OUTPUT jacks
See page 18 for connection information.
8 AC power cord
Connect to a power outlet.
9 AC OUTLET(S)
Use these outlets to supply power to your other A/V
components (see page 19).
0 6CH INPUT jacks
See pages 13 and 18 for connection information.
q IMPEDANCE SELECTOR switch
Use this switch to match the amplifier output to your
speaker impedance. Set this unit in the standby mode
before you change the setting of this switch (see page 19).
DIGITAL OUTPUT AUDIO AUDIO VIDEO
SPEAKERS OUTPUT
MAIN
CENTER
REAR
(SURROUND)
TUNER
DIGITAL INPUT 6CH INPUT
MD/
TAP E
CD-R
CD-R
CD
DVD
FM
ANT
AM
ANT
GND
GND
75
UNBAL.
D-TV
/LD
OPTICAL
OPTICAL
COAXIAL
CD
IN
(PLAY)
DVD
S VIDEO VIDEO COMPONENT
DVD
Y
P
B
/
C
B
P
R
/
C
R
S VIDEO VIDEO
D-TV
/LD
CBL
/SAT
IN
VCR 1
OUT
IN
VCR 2
/DVR
OUT
MONITOR
OUT
R
MD/TAPE
CBL
/SAT
OUT
(REC)
CD
PHONO
MAIN
CENTER
SUB
WOOFER
SURROUND
IN
(PLAY)
CD-R
OUT
(REC)
L R L
MAIN
CENTER
SUB
WOOFER
R L
LR
R
+
–
L
R L
D-TV/LD
A
Y
P
B
/
C
B
P
R
/
C
R
MONITOR
OUT
Y
P
B
/
C
B
P
R
/
C
R
+
–
–
+
+
– –
+
B
REAR
(SURROUND)
MAIN A OR B: 4
MIN. /SPEAKER
A
+
B: 8
MIN. /SPEAKER
CENTER
: 6
MIN. /SPEAKER
REAR
: 6
MIN. /SPEAKER
MAIN A OR B: 8
MIN. /SPEAKER
A
+
B:
16
MIN. /SPEAKER
CENTER
: 8
MIN. /SPEAKER
REAR
: 8
MIN. /SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
SWITCHED
100W MAX. TOTAL
AC OUTLETS
MAINS
876
5
4
32
1
9
0
q
As this terminal is used
for an examination in the
factory, do not connect
any equipment to this
terminal.
11
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
SPEAKER SETUP
Speakers to Be Used
This unit has been designed to provide the best sound-
field quality with a 5-speaker system, using left and right
main speakers, left and right rear speakers, and a center
speaker. If you use different brands of speakers (with
different tonal qualities) in your system, the tone of a
moving human voice and other types of sound may not
shift smoothly. We recommend that you use speakers
from the same manufacturer or speakers with the same
tonal quality.
The main speakers are used for the main source sound
plus the effect sounds. They will probably be the speakers
from your present stereo system. The rear speakers are
used for the effect and surround sounds, and the center
speaker is for the center sounds (dialog, vocals, etc.). If
for some reason it is not practical to use a center speaker,
you can do without it. Best results, however, are obtained
with the full system.
The main speakers should be high-performance models
and have enough power-handling capacity to accept the
maximum output of your audio system. The other
speakers do not have to be equal to the main speakers. For
precise sound localization, however, it is ideal to use
high-performance models that can reproduce sounds over
the full range for the center speaker and the rear speakers.
■ Use of a subwoofer expands your
sound field
It is also possible to further expand your system with the
addition of a subwoofer. The use of a subwoofer is
effective not only for reinforcing bass frequencies from
any or all channels, but also for reproducing the LFE
(low-frequency effect) channel with high fidelity when
the Dolby Digital signal or the DTS signal is played back.
The YAMAHA Active Servo Processing Subwoofer
System is ideal for natural and lively bass reproduction.
Speaker Placement
Refer to the following diagram when you place the
speakers.
Main
speaker (L)
Center speaker
Main speaker (R)
Rear speaker (R)
Rear speaker (L)
1.8 m
■ Main speakers
Place the left and right main speakers an equal distance
from the ideal listening position. The distance of each
speaker from each side of the video monitor should be the
same.
■ Rear speakers
Place these speakers behind your listening position,
facing slightly inwards, nearly 1.8 m (approx. 6 feet)
above the floor.
■ Center speaker
Align the front face of the center speaker with the front
face of your video monitor. Place the speaker as close to
the monitor as possible, such as directly over or under the
monitor and centrally between the main speakers.
Note
• If the center speaker is not used, the center channel sound will
be heard from the left and right main speakers. In this case,
“1A CENTER SP” on the SET MENU is set to NONE (see
page 41 for details).
■ Subwoofer
The position of the subwoofer is not so critical, because
low bass sounds are not highly directional. But it is better
to place the subwoofer near the main speakers. Turn it
slightly toward the center of the room to reduce the wall
reflections.
CAUTION
Some types of speakers interfere with a video monitor.
If this problem occurs, move the speakers away from
the monitor. If you cannot avoid installing the center
speaker or subwoofer near the video monitor, use a
magnetically shielded speaker.
PREPARATION
Subwoofer
12
CONNECTIONS
Before Connecting Components
CAUTION
Never connect this unit and other components to mains power until all connections between components have been
completed.
• Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some
components require different connection methods and have different jack names. Refer to the operation instructions
for each component to be connected to this unit.
• When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or
changer), connect them to the jack with the same number labels as !, #, $ etc. YAMAHA applies this labeling
system to all its products.
• After you have completed all connections, check them again to make sure they are correct.
Connecting Audio Components
■ Connecting to digital jacks
This unit has digital jacks for direct transmission of
digital signals through either coaxial or fiber optic cables.
You can use the digital jacks to input PCM, Dolby Digital
and DTS bitstreams. When you connect components to
both the COAXIAL and OPTICAL jacks, priority is given
to the input signals from the COAXIAL jack. All digital
input jacks are acceptable for 96-kHz sampling digital
signals (see page 25 for details).
y
• You can designate the input for each digital jack according to
your component by using “7 I/O ASSIGNMENT” on the SET
MENU (see page 44 for details).
About the dust protection cap
Pull out the cap from the optical jack
before you connect the fiber optic cable.
Do not discard the cap. When you are not
using the optical jack, be sure to put the
cap back in place. This cap protects the
jack from dust.
Note
• The OPTICAL jacks on this unit conform to the EIA standard.
If you use a fiber optic cable that does not conform to this
standard, this unit may not function properly.
■ Connecting a turntable
PHONO jacks are for connecting a turntable with an MM
or high-output MC cartridge. If you have a turntable with
a low-output MC cartridge, use an inline boosting
transformer or MC-head amplifier when connecting to
these jacks.
y
• The GND terminal does not electrically ground the turntable. It
simply reduces noise in the signal. In some cases, you may
hear less noise if you do not connect to the GND terminal.
■ Connecting a CD player
y
• The COAXIAL CD and OPTICAL CD jacks are available for a
CD player which has coaxial or optical digital output jacks.
• When you connect a CD player to both the COAXIAL CD and
OPTICAL CD jacks, priority is given to the input signals from
the COAXIAL CD jack.
■ Connecting an MD recorder, tape
deck or CD recorder
y
• Only digital signals input from a source such as a CD or DVD
are output from the DIGITAL OUTPUT jacks.
• When you connect your recording component to both the
analog and digital input and output jacks, the priority is given
to the digital signal.
• You can connect an MD recorder to any digital input jack by
using “7 I/O ASSIGNMENT” on the SET MENU (see
page 44).
Notes
• When you connect a recording component to this unit, keep its
power on while using this unit. If the power is off, this unit may
distort the sound from other components.
• When you record from a source component connected to this
unit while this unit is set in the standby mode, the recorded
sound may be distorted. To avoid this problem, turn on this
unit.
13
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONNECTIONS
DIGITAL OUTPUT AUDIO AUDIO VIDEO
TUNER
DIGITAL INPUT 6CH INPUT
MD/
TAPE
CD-R
CD-R
CD
DVD
FM
ANT
AM
ANT
GND
GND
75
UNBAL.
D-TV
/LD
OPTICAL
OPTICAL
COAXIAL
CD
IN
(PLAY)
DVD
S VIDEO VIDEO COMPONENT
DVD
Y
P
B/
C
B
PR/
C
R
S VIDEO VIDEO
D-TV
/LD
CBL
/SAT
IN
VCR 1
OUT
IN
VCR 2
/DVR
OUT
MONITOR
OUT
R
MD/TAPE
CBL
/SAT
OUT
(REC)
CD
PHONO
MAIN
CENTER
SUB
WOOFER
SURROUND
IN
(PLAY)
CD-R
OUT
(REC)
L R L
D-TV/LD
Y
P
B/
C
B
PR/
C
R
MONITOR
OUT
Y
P
B/
C
B
PR/
C
R
L
R
L
R
O
O
O
OUTPUT
GND
L
R
L R
L R
INPUT OUTPUT INPUTOUTPUT
OUTPUT
O
C
COAXIAL
OUTPUT
L
R
L
R
OPTICAL
OUTPUT
OPTICAL
INPUT
OPTICAL
INPUT
OPTICAL
OUTPUT
SUBWOOFER
OUTPUT
CENTER OUTPUT
MAIN
OUTPUT
SURROUND
OUTPUT
L R
L
R
C
O
MD recorder or
tape deck
indicates signal direction
indicates coaxial cables
CD recorder
CD player
Turntable
External decoder
See page 18.
indicates left analog cables
indicates right analog cables
indicates optical cables
(Europe model)
14
CONNECTIONS
Y
P
B/
C
B
PR/
C
R
Connecting Video Components
■ About the video jacks
There are three types of video jacks. Video signals input through the VIDEO jacks are the conventional composit video
signals. Video signals input through the S VIDEO jacks are separated into luminance (Y) and color (C) video signals.
The S-video signals achieve high-quality color reproduction. Video signals input through the COMPONENT VIDEO
jacks are separated into luminance (Y) and color difference (P
B
/C
B
, P
R
/C
R
) video signals. The jacks are also separated
into three for each signal. The description of the component video jacks may be different depending on the component
(e.g. Y, C
B
, C
R
/Y, P
B
, P
R
/Y, B-Y, R-Y etc.). Component video signals provide the best quality in picture reproduction.
If your video component has an S-video output or component video output, you can connect it to this unit. Connect the
S-video signal output jack on your video component to the S VIDEO jack or connect the component signal output jacks
on your video component to the COMPONENT VIDEO jacks.
VIDEO jack
(composite)
S VIDEO jack COMPONENT VIDEO
jacks
y
• Each type of video jack works independently. Signals input
through the composite video, S-video and component jacks are
output through the corresponding composite video, S-video,
and component jacks, respectively.
• If you make S-video connections to this unit, it is not necessary
to make composite video connections. If both types of
connections are made, this unit gives priority to the S-video
signal.
• You can designate the input for the COMPONENT VIDEO A
and B jacks according to your component by using “7 I/O
ASSIGNMENT” on the SET MENU (see page 44 for details).
Notes
• Use a commercially available S-video cable when connecting to the S VIDEO jack, and commercially available video cables when
connecting to the COMPONENT VIDEO jacks.
• When you are using the COMPONENT VIDEO jacks, check the details in the owner’s manual that came with the component being
connected.
■ Video monitor with a 21-pin connector
Make a connection as shown on page 15 with a commercially available SCART-plug connector cable.
■ VIDEO AUX jacks (on the front panel)
These jacks are used to connect any video input source
such as a game console to this unit.
S VIDEO VIDEO
L AUDIO R OPTICAL
VIDEO AUX
AUDIO OUT R
AUDIO OUT L
VIDEO OUT
OPTICAL OUT
S VIDEO OUT
O
V
L
R
S
Game console
15
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONNECTIONS
DIGITAL OUTPUT AUDIO AUDIO VIDEO
TUNER
DIGITAL INPUT 6CH INPUT
MD/
TAPE
CD-R
CD-R
CD
DVD
FM
ANT
AM
ANT
GND
GND
75
UNBAL.
D-TV
/LD
OPTICAL
OPTICAL
COAXIAL
CD
IN
(PLAY)
DVD
S VIDEO VIDEO COMPONENT
DVD
Y
P
B
/
C
B
P
R
/
C
R
S VIDEO VIDEO
D-TV
/LD
CBL
/SAT
IN
VCR 1
OUT
IN
VCR 2
/DVR
OUT
MONITOR
OUT
R
MD/TAPE
CBL
/SAT
OUT
(REC)
CD
PHONO
MAIN
CENTER
SUB
WOOFER
SURROUND
IN
(PLAY)
CD-R
OUT
(REC)
L R L
D-TV/LD
Y
P
B
/
C
B
P
R
/
C
R
MONITOR
OUT
Y
P
B
/
C
B
P
R
/
C
R
L
R
S VIDEO
OUTPUT
S VIDEO
OUTPUT
S VIDEO
OUTPUT
S VIDEO
INPUT
VIDEO
INPUT
S VIDEO
OUTPUT
*1
AUDIO
OUTPUT
AUDIO
OUTPUT
AUDIO INPUT
AUDIO OUTPUT
COAXIAL
OUTPUT
OPTICAL
OUTPUT
RF
OUTPUT
OPTICAL
OUTPUT
VIDEO
OUTPUT
VIDEO
OUTPUT
AUDIO
OUTPUT
VIDEO
OUTPUT
S VIDEO
INPUT
VIDEO
OUTPUT
VIDEO
INPUT
RF
INPUT
O
V
S
O
L
R
L
R
L
R
V
S
COMPONENT
INPUT
COMPONENT
OUTPUT
COMPONENT
OUTPUT
V
S
V
V
S S
L
R
C
C
V
S
L
R
V
L
S
R
V
C
O
Note
• If your LD player has an Dolby Digital RF signal output jack, connect it to this unit
through an RF demodulator (separately purchased).
indicates signal direction
indicates left analog cables
indicates right analog cables
indicates S-video cables
TV/digital TV or
LD player
DVD player
Cable TV or
Satellite tuner
VCR 1 or VCR 2/
DVR (digital
video recorder)
Video monitor
indicates coaxial cables
indicates optical cables
indicates video cables
(Europe model)
LD player
No connection
SCART-plug
*1 You can connect the Dolby
Digital RF signal output of
your LD player to the
COAXIAL jack by using
“7 I/O ASSIGNMENT” on
the SET MENU (see
page 44).
RF
demodulator
16
CONNECTIONS
Connecting the Speakers
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are
faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound
will be unnatural and lack bass.
CAUTION
• Use speakers with the specified impedance shown on the rear panel of this unit.
• Do not let the bare speaker wires touch each other and do not let them touch any metal part of this unit. This could
damage the unit and/or speakers.
If necessary, use the SET MENU to change the speaker mode settings according to the number and size of the speakers
in your configuration after you finish connecting your speakers.
■ Speaker cables
A speaker cord is actually a pair of insulated cables
running side by side. One of the cables is colored or
shaped differently, perhaps with a stripe, groove or ridge.
1 Remove approx. 10 mm (3/8”) of insulation
from each of the speaker cables.
2 Twist the exposed wires of the cable
together to prevent short circuits.
12
■ Connecting to the SPEAKERS terminals
1 Unscrew the knob.
2 Insert one bare wire into the hole in the side
of each terminal.
3 Tighten the knob to secure the wire.
2
1
3
Red: positive (+)
Black: negative (–)
■ MAIN SPEAKERS terminals
One or two speaker systems can be connected to these terminals. If you use only one speaker system, connect it to either
of the MAIN A or B terminals.
■ REAR SPEAKERS terminals
A rear speaker system can be connected to these terminals.
■ CENTER SPEAKER terminals
A center speaker can be connected to these terminals.
10 mm (3/8”)
17
English
INTRODUCTION
PREPARATION
BASIC OPERA-
TION
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
APPENDIX
CONNECTIONS
SPEAKERS OUTPUT
MAIN
CENTER
REAR
(SURROUND)
MAIN
CENTER
SUB
WOOFER
R L
LR
R
+
–
L
R L
A
+
–
–
+
+
– –
+
B
REAR
(SURROUND)
MAIN A OR B: 4
MIN. /SPEAKER
A
+
B: 8
MIN. /SPEAKER
CENTER
: 6
MIN. /SPEAKER
REAR
: 6
MIN. /SPEAKER
MAIN A OR B: 8
MIN. /SPEAKER
A
+
B:
16
MIN. /SPEAKER
CENTER
: 8
MIN. /SPEAKER
REAR
: 8
MIN. /SPEAKER
IMPEDANCE SELECTOR
SET BEFORE POWER ON
SWITCHED
100W MAX. TOTAL
AC OUTLETS
MAINS
Main speakers A
Right Left
Main speakers B
Right Left
(Europe model)
Center speaker Rear speakers
Right Left
Subwoofer
system
Subwoofer connection
See “SUBWOOFER jack” on page 18.
18
CONNECTIONS
Connecting to an External
Amplifier
If you want to increase the power output to the speakers,
or want to use another amplifier, connect an external
amplifier to the OUTPUT jacks as follows.
Note
• When RCA pin plugs are connected to the OUTPUT jacks for
output to an external amplifier, it is not necessary to use the
corresponding SPEAKERS terminals.
1 MAIN jacks
Main channel line output jacks.
Note
• The signals output through these jacks are affected by the
BASS, TREBLE and BASS EXTENSION settings.
2 SUBWOOFER jack
When using a subwoofer with built-in amplifier, including
the YAMAHA Active Servo Processing Subwoofer
System, connect the input jack of the subwoofer system
to this jack. Low bass signals distributed from the main,
center and/or rear channels are directed to this jack. (The
cut-off frequency of this jack is 90 Hz.) The LFE (low-
frequency effect) signals generated when Dolby Digital or
DTS is decoded are also directed if they are assigned to
this jack.
Notes
• Adjust the volume level of the subwoofer with the control on
the subwoofer. The subwoofer volume cannot be adjusted from
this unit.
• Depending on the settings of “1 SPEAKER SET”, “10A LFE
LEVEL” and “11 DTS LFE LEVEL” on the SET MENU,
some signals may not be output from the SUBWOOFER jack.
3 CENTER jack
Center channel line output jack.
4 REAR (SURROUND) jacks
Rear channel line output jacks.
OUTPUT
MAIN
CENTER
SUB
WOOFER
R L
LR
REAR
(SURROUND)
1
2
3
4
Connecting an External Decoder
This unit is equipped with 6 additional input jacks (left
and right MAIN, CENTER, left and right SURROUND
and SUBWOOFER) for discrete multi-channel input from
an external decoder, sound processor or pre-amplifier.
Connect the output jacks on your external decoder to the
6CH INPUT jacks. Be sure to match the left and right
outputs to the left and right input jacks for the main and
surround channels.
Notes
• When you select 6CH INPUT as the input source, this unit
automatically turns off the digital sound field processor, and
you cannot listen to DSP programs.
• When you select 6CH INPUT as the input source, changing
items 1A to 1E on the SET MENU is not affected.
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
/