Samsung RF263BEAESG Инструкция по применению

Refrigerator

user manual

imagine the possibilities

Thank you for purchasing a Samsung product.

To receive a more complete service,

please register your product at

www.samsung.com/register

Free Standing Appliance

Eng lish

DA68-02615D Rev. 03

02_ Safety information

safety information

SAFETY INFORMATION

Before operating the appliance, please read •

this manual thoroughly and retain it for your

reference.

Use this appliance only for its intended •

purpose as described in this instruction

manual. This appliance is not intended for use

by persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they

have been given supervision or instruction

concerning use of the appliance by a person

responsible for their safety.

Warnings and Important Safety Instructions •

in this manual do not cover all possible

conditions and situations that may occur. It

is your responsibility to use common sense,

caution, and care when installing, maintaining,

and operating your appliance.

Because these following operating instructions •

cover various models, the characteristics of

your refrigerator may differ slightly from those

described in this manual. R600a or R134a is

used as a refrigerant. Check the compressor

label on the rear of the appliance or the rating

label inside the fridge to see which refrigerant

is used for your refrigerator. When this product

contains ﬂ ammable gas (Refrigerant R600a),

contact your local authority in regard to safe

disposal of this product.

Important safety symbols and

precautions:

WARNING

Hazards or unsafe practices that may result in

severe personal injury or death.

CAUTION

Hazards or unsafe practices that may result in

minor personal injury or property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions carefully.

Unplug the power plug from the wall socket.

Make sure the refrigerator is grounded to

prevent electric shock.

Call the contact center for help.

Note.

These warning signs are here to prevent

injury to you and others.

Please follow them carefully.

After reading this section, keep it in a safe

place for future reference.

CE Notice

This product has been determined to be in

compliance with the Low Voltage Directive

(2006/95/ EC), the Electromagnetic Compatibility

Directive (2004/108/EC) and the Eco-Design

Directive (2009/125/EC) implemented by Regulation

(EC) No 643/2009 of the European Union.

SEVERE WARNING SIGNS

FOR TRANSPORTATION

AND SITE

• When transporting and installing the

appliance,care should be taken to

ensure that no parts of the refrigerating

circuit are damaged.

When this product contains ﬂ ammable gas •

(Refrigerant R600a),

Refrigerant leaking from the pipe work could -

ignite or cause an eye injury. If a leak is

detected, avoid any naked ﬂ ames or potential

sources of ignition and air the room in which

the appliance is standing for several minutes.

In order to avoid the creation of a ﬂ ammable -

gas-air mixture if a leak in the refrigerating

circuit occurs, the size of the room in which

the appliance may be sited depends on the

amount of refrigerant used.

Never start up an appliance showing any signs -

of damage. If in doubt, consult your dealer.

The room where the refrigerator will be sited

must be 1 m³ in size for every 8 g of R600a

refrigerant inside the appliance. The amount of

refrigerant in your particular appliance is shown

on the identiﬁ cation plate inside the appliance.

If the appliance contains isobutane refrigerant -

(R600a), a natural gas with high environmental

compatibility that is, however, also combustible.

When transporting and installing the appliance,

care should be taken to ensure that no parts of

the refrigerating circuit are damaged.

WARNING

Safety information _03

SEVERE WARNING SIGNS

FOR INSTALLATION

• Do not install this appliance near a

heater, inﬂ ammable material.

Do not install this appliance in a humid,

oily or dusty location, in a location

exposed to direct sunlight and water (rain

drops).

Do not install this appliance in a location

where gas may leak.

This may result in an electric shock or ﬁ re. -

Do not place this refrigerator in direct sunlight •

or expose to the heat from stoves, room

heaters or other appliances.

Do not plug several appliances into the same •

multiple power board.

The refrigerator should always be plugged into

its own individual electrical outlet which has a

voltage rating that matched the rating plate.

This provides the best performance and -

also prevents overloading house wiring

circuits, which could cause a ﬁ re hazard from

overheated wires. If the wall socket is loose, do

not insert the power plug.

There is a risk of electric shock or ﬁ re. -

Do not use a cord that shows cracks or •

abrasion damage along its length or at either

end.

Do not bend the power cord excessively or •

place heavy articles on it.

Do not use aerosols near the refrigerator.•

Aerosols used near the refrigerator may cause -

an explosion or ﬁ re.

• The installation or any service of this

appliance is recommended by a

qualiﬁ ed technician or service company.

Failing to do so may result in an electric shock, -

ﬁ re, explosion, problems with the product, or

injury.

This refrigerator must be properly installed and •

located in accordance with the manual before

it is used.

Connect the power plug in proper position with •

the cord hanging down.

If you connect the power plug upside down, -

wire can get cut off and a cause ﬁ re or an

electric shock.

Make sure that the power plug is not squashed •

or damaged by the back of the refrigerator.

When moving the refrigerator, be careful not to •

roll over or damage the power cord.

This constitutes a ﬁ re hazard. -

WARNING

The appliance must be positioned so that the •

plug is accessible after installation.

• This appliance must be properly

grounded. Do not ground the appliance

to a gas pipe, plastic water pipe, or

telephone line.

You must ground the refrigerator to prevent -

any power leakages or electric shocks caused

by current leakage from the refrigerator.

This may result in an electric shock, ﬁ re, -

explosion, or problems with the product.

Never plug the power cord into a socket that is -

not grounded correctly and make sure that it is

in accordance with local and national codes.

Do not pull or excessively bend the power •

cord.

Do not twist or tie the power cord.

Do not hook the power cord over a metal

object, place a heavy object on the power

cord, insert the power cord between objects,

or push the power cord into the space behind

the appliance.

When moving the refrigerator, be careful not to -

roll over or damage the power cord.

This may result in an electric shock or ﬁ re. -

This appliance should be positioned in such a •

way that it is accessible to the power plug.

Failing to do so may result in an electric shock -

or ﬁ re due to electric leakage.

Do not stand on top of the appliance or place •

objects (such as laundry, lighted candles,

lighted cigarettes, dishes, chemicals, metal

objects, etc.) on the appliance.

This may result in an electric shock, ﬁ re, -

problems with the product, or injury.

Never use gas pipes, telephone lines or other •

potential lightening rods as ground.

Improper use of the ground plug can result in -

an electric shock.

• If the power cord is damaged,

have it replaced immediately by the

manufacturer or its service agent.

The fuse on the refrigerator must be changed •

by a qualiﬁ ed technician or service company.

Failing to do so may result in an electric shock -

or personal injury.

04_ Safety information

CAUTION SIGNS FOR

INSTALLATION

• Keep ventilation opening in the appliance

enclosure or mounting structure clear of

obstruction.

A) Allow the appliance to stand for 2hours after •

installation.

B) To get Best performance from the product,•

1) Do not place foods too closely in front of -

the vents at the rear of the appliance as it

can obstruct free air circulation in the freezer

compartment.

2) Wrap the food up properly or place it in -

airtight containers before putting it into the

fridge or freezer.

3) Do not put any newly introduced food for -

freezing near to already existing food.

C) Do not place glass or bottles or carbonated •

beverages into the freezer.

The container may freeze and break, and this -

may result in injury.

D) Please observe maximum storage times and •

expiry dates of frozen goods.

E) There is no need to disconnect the •

refrigerator from the power supply if you will be

away for less than three weeks. But, Remove

all the food if you are going away for the three

weeks or more.

Unplug the refrigerator and clean it, rinse and

dry.

SEVERE WARNING SIGNS

FOR USING

• Do not insert the power plug with wet

hands.

Do not touch the power plug with wet hands.•

This may result in an electric shock. Do not put -

a container ﬁ lled with water on the refrigerator.

If spilled, there is a risk of ﬁ re or electric shock.

Do not store articles on the top of the •

appliance.

When you open or close the door, the articles -

may fall and cause a personal injury and/or

material damage.

Do not put items ﬁ lled with water on the •

refrigerator.

If spilled, there is a risk of ﬁ re or electric shock. -

Do not let children hang on the door.

Failure to do so may cause serious personal -

injury.

Do not leave the doors of the refrigerator open •

CAUTION

WARNING

while the refrigerator is unattended and do not

let children enter inside the refrigerator.

Do not allow babies or children go inside the •

drawer.

It can cause death from suffocation by -

entrapment or personal injury.

Do not sit on the Freezer door.•

The door may be broken and cause a personal -

injury.

To prevent children entrapment, you must •

reinstall the divider using provided screws after

cleaning or other actions if you removed the

divider from the drawer.

Never put ﬁ ngers or other objects into the •

dispenser hole.

Failure to do so may cause personal injury or -

material damage.

Do not store volatile or ﬂ ammable substances •

such as benzene, thinner, alcohol, ether or LP

gas in the refrigerator.

The storage of any of such products may -

cause an explosion.

Do not store low temperature-sensitive •

pharmaceutical products, scientiﬁ c materials

or other low temperature-sensitive products in

the refrigerator.

Products that require strict temperature -

controls must not be stored in the refrigerator.

Do not place or use electrical appliance inside •

the refrigerator/freezer, unless they are of a

type recommended by the manufacturer.

If gas leak is detected, avoid any naked ﬂ ames

or potential sources of ignition and air the room

in which the appliance is standing for several

minutes.

Do not use a hair dryer to dry the inside of the •

refrigerator. Do not place a lighted candle in

the refrigerator for removing bad odors.

This may result in an electric shock or ﬁ re. -

Do not touch the inside walls of the freezer or •

products stored in the freezer with wet hands.

This may cause frostbite. -

Do not use mechanical devices or any other •

means to accelerate the defrosting process,

other than those recommended by the

manufacturer.

Do not damage the refrigerant circuit.•

• This product is intended only for

the storage of food in a domestic

environment.

Bottles should be stored tightly together so •

Safety information _05

that they do not fall out.

In the event of a gas leak (such as propane •

gas, LP gas, etc.), ventilate immediately

without touching the power plug. Do not touch

the appliance or power cord.

Do not use a ventilating fan. -

A spark may result in an explosion or ﬁ re. -

Children should be supervised to ensure that •

they do not play with the appliance. Keep

ﬁ ngers out of “pinch point” areas : clearances

between the doors and cabinet are necessarily

small. Be careful when you open the doors

when children are in the area. Do not let

children hang on the door. If not, a serious

injury may occur. There is a Risk of children

entrapment. Do not let children enter inside the

refrigerator. Never put ﬁ ngers or other objects

into the dispenser hole, ice chute and ice

maker bucket.

It may cause a personal injury or material -

damage.

• Do not attempt to repair, disassemble,

or modify the appliance yourself.

Do not use any fuse(such as cooper, steel wire, -

etc.) other than the standard fuse.

When repairing or reinstalling the appliance is -

required, contact your nearest service center.

Failing to do so may result in an electric shock, -

ﬁ re, problems with the product, or injury.

• If the appliance generates a strange

noise, a burning or smell or smoke,

unplug the power plug immediately and

contact your nearest service center.

Failing to do so may result in an electric or ﬁ re -

hazards.

If you experience difﬁ culty when changing the •

light, contact service agent.

If the products is equipped with the LED Lamp, •

do not disassemble the Lamp Cover and LED

Lamp by yourself.

Please contact your service agent. -

Use only the LED Lamps provided by

manufacturer or service agent.

If any dust or water is in the refrigerator, pull •

out power plug and contact your Samsung

Electronics service center.

Otherwise there is a risk of ﬁ re. -

Plug the power plug into the wall socket ﬁ rmly. •

Do not use a damaged power plug, damaged

power cord or loose wall socket.

This may result in an electric shock or ﬁ re. -

CAUTION SIGNS FOR

USING

• To get best performance from the

product,

Do not place foods too closely in front of the -

vents at the rear of the appliance as it can

obstruct free air circulation in the refrigerator

compartment.

Wrap the food up properly or place it in airtight -

containers before putting it into the refrigerator.

Do not put any newly introduced food for -

freezing near to already existing food.

Do not place carbonated or ﬁ zzy drinks in the •

freezer compartment. Do not put bottles or

glass containers in the freezer.

When the contents freeze, the glass may -

break and cause personal injury and property

damage.

Do not change or modify the functionality of •

the refrigerator.

Changes or modiﬁ cations may result in a -

personal injury and/or property damage. Any

changes or modiﬁ cations performed by a

3rd party on this completed appliance are

neither covered under Samsung warranty

service, nor is Samsung responsible for safety

issues and damages that result from 3rd party

modiﬁ cations.

Do not block air holes.•

If the air holes are blocked, especially with a -

plastic bag, the refrigerator can be over cooled.

If this cooling period lasts too long, the water

ﬁ lter may break and cause water leakage.

Please observe maximum storage times and •

expiry dates of frozen goods.

Fill the water tank, ice tray, water cubes only •

with potable water.

Use only the ice-maker provided with the •

refrigerator.

The water supply to this refrigerator must only •

be installed/connected by a suitably qualiﬁ ed

person and connected to a potable water

supply only.

In order to operate the ice-maker properly, •

water pressure of 138~862 kPa(1.4~8.8 kgf/

cm

3

) is required.

Do not spray volatile material such as •

insecticide onto the surface of the appliance.

As well as being harmful to humans, it may -

also result in an electric shock, ﬁ re or problems

with the product.

CAUTION

06_ Safety information

CAUTION SIGNS

FOR CLEANING AND

MAINTENANCE

• Do not directly spray water inside or

outside the refrigerator.

There is a risk of ﬁ re or electric shock. -

Do not use or place any substances sensitive •

to temperature such as inﬂ ammable sprays,

inﬂ ammable objects, dry ice, medicine, or

chemicals near the refrigerator. Do not keep

volatile or inﬂ ammable objects or substances

(benzene, thinner, propane gas, alcohol, ether,

LP gas and other such products etc.) in the

refrigerator.

This refrigerator is for storing food only. -

This may result in ﬁ re or explosion. -

Do not store pharmaceuticals products, •

scientiﬁ c materials or temperature-sensitive

products in the refrigerator.

Products that require strict temperature -

controls must not be stored in the refrigerator

If you smell pharmaceutical or smoke, pull

out power plug immediately and contact your

Samsung Electronics service center Remove

all foreign substances such as dust or water

from the power plug terminals and contact

points using a dry cloth on a regular basis.

Unplug the power plug and clean it with a dry -

cloth.

Failing to do so may result in an electric shock -

or ﬁ re.

Do not spray cleaning products directly on the •

display.

Printed letters on the display may come off. -

Remove any foreign matter or dust from the •

power plug pins. But do not use a wet or

damp cloth when cleaning the plug, remove

any foreign material or dust from the power

plug pins.

Otherwise there is a risk of ﬁ re or electric -

shock.

Never put ﬁ ngers or other objects into the •

dispenser hole and ice chute.

It may cause a personal injury or material -

damage.

• Unplug the refrigerator before cleaning

and performing maintenance.

CAUTION

SEVERE WARNING SIGNS

FOR DISPOSAL

• Ensure that none of the pipes on the

back of the appliance are damaged prior

to disposal.

R600a or R134a is used as a refrigerant. •

Check the compressor label on the rear of

the appliance or the rating label inside the

refrigerator to see which refrigerant is used for

your refrigerator. When this product contains

ﬂ ammable gas (Refrigerant R600a), contact

your local authority in regard to safe disposal

of this product. Cyclopentane is used as an

insulation blowing gas. The gases in insulation

material require special disposal procedure.

Please contact your local authorities in regard

to the environmentally safe disposal of this

product. Ensure that none of the pipes on the

back of the appliances are damaged prior to

disposal. The pipes shall be broken in the open

space.

When disposing of this or other refrigerator/s, •

remove the door/door seals, door latch so that

children or animals cannot become trapped

inside. Children should be supervised to

ensure that they do not enter and play with the

appliance.

If trapped inside, the child may become injury -

and suffocate to death. Leave the shelves in

place so that children may not easily climb

inside.

Ensure that none of the pipes on the back of •

the appliance are damaged prior to disposal.

R600a or R134a is used as a refrigerant. •

Check the compressor label on the rear of

the appliance or the rating label inside the

fridge to see which refrigerant is used for

your refrigerator. When this product contains

ﬂ ammable gas (Refrigerant R600a) contact

your local authority in regard to safe disposal of

this product.

Cyclopentane used as an insulation blowing •

gas. The gases in insulation material require

special disposal procedure. Please contact

your local authorities in regard to the

environmentally safe disposal of this product.

Ensure that none of the pipes on the back of

the appliances are damaged prior to disposal.

The pipes shall be broken in the open space.

Please dispose of the packaging material for •

this product in an environmentally friendly

manner.

WARNING

Safety information _07

ADDITIONAL TIPS FOR

PROPER USAGE

In the event of a power failure, call the local •

ofﬁ ce of your Electricity Company and ask how

long it is going to last.

Most power failures that are corrected within -

an hour or two will not affect your refrigerator

temperatures. However, you should minimize

the number of door openings while the power

is off.

Should the power failure last more than 24 -

hours, remove all frozen food.

If keys are provided with the refrigerator, •

the keys should be kept out of the reach

of children and not be in the vicinity of the

appliance.

The appliance might not operate consistently •

(possibility of temperature becoming too warm

in the refrigerator) when sited for an extended

period of time below the cold end of the range

of temperature for which the refrigerating

appliance is designed.

Do not store food which spoils easily at low •

temperature, such as bananas, melons.

Your appliance is frost free, which means there •

is no need to manually defrost your appliance,

as this will be carried out automatically.

Temperature rise during defrosting can comply •

with ISO requirements. But if you want to

prevent an undue rise in the temperature of

the frozen food while defrosting the appliance,

please wrap the frozen food up in several

layers of newspaper.

Any increase in temperature of frozen food •

during defrosting can shorten its storage life.

Saving Energy Tips

Install the appliance in a cool, dry room with -

adequate ventilation.

Ensure that it is not exposed to direct sunlight

and never put it near a direct source of heat

(radiator, for example).

Never block any vents or grilles on the -

appliance.

Allow warm food to cool down before placing it -

in the appliance.

Put frozen food in the refrigerator to thaw. -

You can then use the low temperatures of the

frozen products to cool food in the refrigerator.

Do not keep the door of the appliance open for -

too long when putting food in or taking food

out. The shorter time for which the door is

open, the less ice will form in the freezer.

Clean the rear of the refrigerator regularly. Dust -

increases energy consumption.

Do not set temperature colder than necessary. -

Ensure sufﬁ cient air exhaust at the refrigerator -

base and at the back wall of the refrigerator.

Do not cover air vent openings.

Allow clearance to the right, left, back and top -

when installing.

This will help reduce power consumption and

keep your energy bills lower.

In the event of a power failure, call the local -

ofﬁ ce of your Electricity Company and ask how

long it is going to last.

Most power failures that are corrected in an

hour or two will not affect your refrigerator

temperatures. However, you should minimize

the number of door openings while the power

is off. But Should the power failure last more

than 24hours, remove all frozen food.

If the key is provided with refrigerator, the keys -

should be kept out of the reach of children and

not be in the vicinity of the appliance.

The appliance might not operate consistently -

(possibility of defrosting of co tents or

temperature becoming too warm in the frozen

food compartment) when sited for an extended

period of time below the cold end of the range

of temperatures for which the refrigerating

appliance is designed.

Do not store food which goes bad easily at low -

temperature, such as bananas, melons.

Your appliance is frost free, which means there -

is no need to manually defrost your appliance,

as this will be carried out automatically.

Temperature rise during defrosting can comply -

with ISO requirements.

08_ Safety information

But If you want to prevent an undue rise in the

temperature of the frozen food while defrosting

the appliance, please wrap the frozen food up

in several layers of newspaper.

Any increase in temperature of frozen food -

during defrosting can shorten its storage life.

Do not re-freeze frozen foods that have thawed -

completely.

Contains ﬂ uorinated greenhouse gases -

covered by the Kyoto Protocol.

Hermetically sealed system. -

Do not vent gases into the atmosphere. -

Refrigerant type: R-134a -

Quantity: 0.16 Kg

Global Warming Potential (GWP) = 1300

To get the best energy efﬁ ciency of this -

product, please leave all selves, drawers and

baskets on their original position like as above

illustration.

contents

SETTING UP YOUR FRENCH DOOR REFRIGERATOR ………………………………… 09

OPERATING YOUR FRENCH DOOR REFRIGERATOR …………………………………… 15

TROUBLESHOOTING ………………………………………………………………………… 25

setting up _09

01 SETTING UP

Setting up your French Door

Refrigerator

GETTING READY TO INSTALL

THE REFRIGERATOR

Congratulations on your purchase of this Samsung

French Door Refrigerator.

We hope you enjoy the state-of-art features and

efﬁ ciencies that this new appliance offers.

Selecting the best location for the

refrigerator

A location with easy access to a water supply.•

A location without direct exposure to sunlight.•

A location with a leveled ﬂ oor.•

A location with enough space for the •

refrigerator doors to open easily.

A location that allows sufﬁ cient space to the •

right, left, back and top for air circulation.

A location that allows you to move the •

refrigerator easily if it needs maintenance or

service.

Allow clearance to the right, left, back and top •

when installing. This will help reduce power

consumption and keep your energy bills lower.

Do not install the refrigerator where the •

temperature will go below (10 ºC).

Do not locate the refrigerator where it may •

become wet.

Do not install the refrigerator in a damp place or •

place where it may come in contact with water.

Deteriorated insulation of electrical parts may -

cause an electric shock or ﬁ re.

When you use this function the energy •

consumption of the refrigerator will increase.

Remember to turn it off when you don’t -

need it and return the freezer to your original

temperature setting power freezing

If you need to freeze large amount of food -

stuff, activate Power Freeze function at least

24 hours before.

To get more space , you can remove top •

freezer drawers since it does not affect thermal

and mechanical characteristics. A declared

storage volume of frozen food storage

compartment is calculated with these drawers

removed.

Never stare directly at the UV LED lamp for •

long periods of time.

This may result in eye strain due to the -

ultraviolet rays.

When moving your refrigerator

To prevent ﬂ oor damage, be sure the front

adjusting legs are in the up position (above

the ﬂ oor). Refer to ‘Adjusting the Level’ in

the manual (on page 12).

FLOORING

For proper installation, you must place this

refrigerator on a level, hard surface that is the

same height as the rest of the ﬂ oor. This surface

should be strong enough to support a fully loaded

refrigerator, or approximately 150 kg.

To protect the ﬁ nish of the ﬂ ooring, cut a large

section of the cardboard carton and place it under

the refrigerator where you are working. When

moving the refrigerator, you need to pull and push

CAUTION

50 mm

86 mm

908 mm

1324 mm

745 mm545 mm

475 mm

1220 mm

10_ setting up

it straight forwards or back. Do not wiggle it from

side to side.

REMOVING THE

REFRIGERATOR DOORS

For some installations you need to remove the

fridge and freezer drawers so you can move the

refrigerator to its ﬁ nal location. Do not remove

the doors/drawer if you don’t need to. If you do

not need to remove the refrigerator doors, go to

Adjusting the Level on page 12. If you need to

remove the doors. continue below.

Before removing the door/drawer, make sure you

read the following items:

Required Tools (Not provided)

You need the following tools to complete the

installation of your refrigerator:

Philips

screwdriver(+)

Flat-blade screw

driver(-)

Socket wrench

(10 mm)

Pliers

Allen wrench

(5 mm)

Disconnect power to the refrigerator before

removing the door or drawer.

• Be careful not to drop, damage or

scratch the door/drawer while removing

them.

Be careful not to get injured while removing the •

door/drawer.

Reattach the door/drawer properly to avoid: •

Moisture from air leakage. -

Uneven door alignment. -

Wasting energy due to improper door seal. -

WARNING

Disassemble the refrigerator doors

Be careful not to drop and scratch the

doors while removing the doors.

With the door opened

Remove 3 screws holding down the TOP 1.

TABLE ( 1 ) and turn it with wires connected.

Disconnect two connector ( 2. 2 ) on the left side

door. To remove the water coupler from the

hinge, twist and pull it from the hinge. Remove

the water line ( 3 ) while pressing the marked

part ( 4 ) of the water line coupler.

If a red clip is on the coupler, it must be

removed before removing the tube.

Pull and remove the hinge lever ( 3. 5 ) . Remove

the ground screw ( 6 ) attached to the upper

left door hinges with a philips screwdriver (+).

Remove the upper left and right door hinges

( 7 ).

WARNING

CAUTION

1

2

3

4

Red Clip

(1/4")

5

6

7

setting up _11

01 SETTING UP

Lift the door straight up to remove.4.

Remove the screw (5. 8 ) attached to the

lower left and right door hinges with a philips

screwdriver (+). Remove the 2 hex head bolts

( 9 ) attached to the lower left and right door

hinges with an allen wrench. Remove the lower

left and right door hinges ( 10 ).

REATTACHING THE

REFRIGERATOR DOORS

To reattach the fridge doors after you have moved

the fridge to its ﬁ nal location, assemble parts in

reverse order.

The Water Line must be fully Inserted to the 1.

center of transparent coupler to prevent water

leakage from the dispenser.

Insert2.

the clip in the install pack and check that it

holds the line ﬁ rmly.

DISASSEMBLE THE FLEX DOOR

Take out the upper drawer by lifting it up.1.

Take out the lower basket ( 2. 1 ) by lifting the

basket up from the rail system.

Press the ﬁ xing hook of rail system. 3.

After holding and pulling out the top of Freezer 4.

Door, remove it at the rail system.

Make sure there is no scratch at the end of

Sliding Rail by being dented from the ﬂ oor.

CAUTION

Allen wrench

10

8

9

1

Center of transparent

coupler

clip A

(6.35 mm)

12_ setting up

Make sure that you mount the freezer

basket in the right position when removing

/ installing the freezer door. Failing to do

so may result in the door not opening or

closing properly.

ASSEMBLE THE FREEZER

DRAWER

To reattach the drawer after you have moved

the fridge to its ﬁ nal location, assemble parts in

reverse order.

ADJUSTING THE LEVEL

Make sure the refrigerator is level so that you can

make ﬁ nal adjustments. Use a level to test if the

refrigerator is level both side to side and back to

front. If the refrigerator is not level, it will not be

possible to get the doors perfectly even, which

may cause moisture condensation and increased

energy bills. Below is an example of how to level

the refrigerator if the left side of the refrigerator is

lower than the right side.

How to adjust the level

Open the freezer drawer and remove the lower 1.

basket.

Insert a ﬂ at-blade screwdriver (-) into a notch 2.

on the left control lever, and turn it count

clockwise to level the refrigerator. (You turn the

lever clockwise to lower the refrigerator and

counterclockwise to raise it.)

CAUTION

Both control levers must be touching the

ﬂ oor to avoid possible personal injury or

property damage because of tipping.

If the right side is lower, perform the same

procedure, but with the right control lever.

It is difﬁ cult to remove the cover leg

front from the refrigerator, so we do not

recommend making small adjustments

with the control lever. Instead, refer to the

next page for the best way to make minor

adjustments to the doors.

MAKING MINOR

ADJUSTMENTS BETWEEN

DOORS

Remember, a leveled refrigerator is necessary

for getting the doors perfectly even. If you need

help, review the previous section on leveling the

refrigerator.

The left door is ﬁ xed. To make minor

adjustments between doors, adjust only

the right door.

CAUTION

ﬂ at-blade screwdriver(-)

Control Lever

Adjustment

part

Fixed part

setting up _13

01 SETTING UP

Pull out the freezer drawer ( 1. 1 ), then you can

see the lower hinge ( 2 ).

Insert the supplied allen wrench ( 2. 3 ) into the

shaft ( 4 ) of the lower hinge.

Please adjust the height by turning the 3.

hex wrench ( 3 ) clockwise (

DOWN

) or

counterclockwise (

UP

).

When you turn the hex wrench counter-

clockwise(

), the door will move up.

After adjusting the doors, insert the supplied 4.

fastener ( 6 ) using a pliers ( 5 ) in the gap

between the hinge-grommet ( 7 ) and the lower

hinge ( 8 ). The number of fasteners you’ll need

to insert depends on the gap.

2 fastener are enclosed with the refrigerator.

The thickness of each fastener is 1 mm.

INSTALLING THE WATER

DISPENSER LINE

A water dispenser with a ﬁ lter is one of the helpful

features on your new refrigerator. To help promote

better health, the water ﬁ lter removes unwanted

particles from your water. However, it does not

sterilize or destroy microorganisms. You may need

to purchase a water purifying system to do that.

In order for the ice maker to operate properly, a

water pressure of 138~862 kPa is required.

Under normal conditions, a 0.17 L cup can be

ﬁ lled in about 10 seconds.

If the refrigerator is installed in an area with low

water pressure, you can install a booster pump to

compensate for the low pressure.

After you have connected the water line, make

sure the water storage tank inside the refrigerator is

properly ﬁ lled. To do this, press the water dispenser

lever until the water runs from the water outlet.

Water line installation kits are available at

extra cost from your dealer.

We recommend using a water line

installation kit that contains copper tubing

and compression nut.

Connecting to the water supply line

First, shut off the main water 1.

supply.

Locate the nearest cold water drinking line and 2.

install the pipe clamp and shut off valve.

Connect the water line installation kit to the 3.

shut off valve.

Connecting the water supply line to

the refrigerator.

There are several items that you need to purchase

to complete this connection.

You may ﬁ nd these items sold as a kit at your local

hardware store.

Use Copper Tubing Use Plastic Tubing

copper tubing•

compression nut (1pc)•

Ferrule (2pc)•

plastic tubing •

→

Molded end(Bulb)

compression nut (1pc)•

Pipe clamp

Cold water line

Shut off valve

Pipe clamp

Cold water line

Water line installation kit

3

1

2

3

4

14_ setting up

Slip the compression nut through the supplied 1.

plastic tubing

.

Tighten the compression nut 2.

onto the

6.35 mm compression ﬁ tting.

If you are using copper tubing, slip the -

compression nut (not included) and ferrule

(not included) on copper tubing (not included)

as shown.

If you are using plastic tubing -

, insert the

molded end (Bulb) of the plastic tubing into

the compression ﬁ tting.

Do not use without the molded end(Bulb) of

the plastic tubing .

Tighten the compression nut 3.

onto the

compression ﬁ tting. Do not over-tighten the

compression nut

.

Turn water on and check for any leakage. 4.

Only connect the water line to a drinkable

water source. If you have to repair or

disassemble the water line, cut off 6.35 mm

of the plastic tubing to make sure you get

a snug, leak-free connection.

CAUTION

COMPLETING THE SET UP

Now that you have your new refrigerator installed

in place, you are ready to set up and enjoy the

features and functions of the appliance.

By completing the following steps, your refrigerator

should be fully operational.

Make sure your refrigerator is in an appropriate 1.

location with reasonable clearance between it

and the wall. Refer to installation instructions in

this manual.

Once the refrigerator is plugged in, make sure 2.

the interior light comes on when you open the

doors.

Set the Temperature control to the coldest 3.

temperature and wait for an hour. The freezer

will get slightly chilled and the motor will run

smoothly. Reset the refrigerator and freezer to

the temperatures you want.

After you plug the refrigerator in, it will 4.

take a few hours to reach the appropriate

temperature. You can store food and drinks

in the refrigerator after the temperature is

sufﬁ ciently cool.

Plastic tubing

(Supplied)

Ferrule

(Not supplied)

Compression nut

(6.35 mm) (Supplied)

Compression ﬁ tting

(Supplied)

Bulb

Compression nut

(6.35 mm)

(Not supplied)

Copper tubing

or

Plastic tubing

(Not supplied) (Not supplied)

Household water line

Refrigerator

operating _15

02 OPERATING

Operating your French Door

Refrigerator

USING THE CONTROL PANEL

( 1 ) Energy

Saver

Hold 3 sec for

°C↔°F

Touching this button turns Energy Saver

mode on and off. When you turn Energy

Saver on, the Energy Saver icon lights.

Turn Energy Saver off and the icon

goes off. The Energy Saver function

automatically turns on when power is

supplied to the refrigerator.

If condensation or water drops appear

on the doors, turn the Energy Saver

mode off.

Touch and hold this button for 3

seconds to switch the temperature units

between °C and °F.

( 2 ) Freezer

(Hold 3 sec

for Power

Freeze)

Touch this button to set the freezer to

your desired temperature.

You can set the temperature between

-8 °F and 5 °F (between -23 °C and

-15 °C). Touch and hold this button for

3 seconds to decrease the time needed

to freeze products in the Freezer. It can

be helpful if you need to quickly freeze

easily spoiled items or if the temperature

in the freezer has warmed dramatically

(For example, if the door was left open).

( 3 ) Ice

Type/Water

Hold 3 sec for

Filter Reset

Touch this button to select the ice or

water function. You can select water or

the types of ice(cubed/crushed ice).

Each time you press the button, the

cubed and crushed

ice modes alternate and the Cubed or

Crushed ice icon lights up, indicating

your selection.

After you replace the water ﬁ lter, touch

and hold this button for 3 seconds to

reset the water ﬁ lter life indicator.

( 4 ) Alarm

Hold 3 sec for

Lighting

To turn the door open alarm on and off

If the door alarm is set to On, an alarm

beeps if any refrigerator door is left open

for more than three minutes.

The beeping stops when you close the

door. The door alarm function is preset

to On in the factory. You can turn it

off by touching and then releasing this

button. You can turn it back on in the

same fashion. The icon lights up when

the function is on.

If you touch and hold the Alarm/Lighting

button for 3 seconds, the dispenser LED

Lamp will stay on.

( 5 ) Fridge

Hold 3 sec for

Power Cool

Touch this button to set the fridge to

your desired temperature. You can set

the temperature between 34 °F and

44 °F (between 7 °C and 1 °C). Touch

and hold this button for 3 seconds

to decrease the time needed to cool

products in the Refrigerator. It can be

helpful if you need to quickly cool easily

spoiled items or if the temperature in

the fridge has warmed dramatically (For

example, if the door was left open).

( 6 ) Ice Off

Hold 3 sec for

Child Lock

If you don’t want to make more ice,

touch the Ice Off button.

Touching this button for 3 seconds turns

on Child Lock which locks the display

panel and dispenser buttons so the

buttons can not be used. The Child Lock

icon lights up to indicate you’ve activated

the Child Lock function. Press 3 seconds

to unlock.

( 7 ) Ice Off

If you don’t want to make more ice,

touch the Ice Off button.

The icon will light up and the Ice-Maker

stops making ice.

We recommend you to stop ice

making if the following occur:

-

There is enough ice in the ice bucket.

-

You want to save water and energy.

- Water is not being supplied to

the refrigerator.

If the ice maker function is

ON, and the water Line is not

connected, there will be a water

valve noise from the back of the

unit, press the Ice Off (Hold 3sec

for child lock) button for less

than 3 seconds until the Ice Off

Indicator (

) illuminates.

(RF263T**)

(RF263B/N**)

8

7

1

2

3

5

6

4

16_ operating

( 8 ) Filter Water ﬁ lter usage

This icon will light up when you need to

change the ﬁ lter. After you use about

300 gallons of water, the ﬁ lter indicator

lights up. (about 6 months). After you

install the new water ﬁ lter, reset the ﬁ lter

indicator by touching the Alarm/hold 3

sec for Filter Reset button.

If water is not dispensing or •

dispensing slowly, you need to

replace the water ﬁ lter because

the water ﬁ lter is clogged.

Some areas have large amounts •

of lime in their water, which

causes the water ﬁ lter to clog

more quickly.

CHANGING THE WATER FILTER

To reduce risk of water damage to your

property DO NOT use generic brands

of water ﬁ lters in your SAMSUNG

Refrigerator.

USE ONLY SAMSUNG BRAND WATER FILTER.

SAMSUNG will not be legally responsible for any

damage, including, but not limited to property

damage caused by water leakage from use of a

generic water ﬁ lter. SAMSUNG Refrigerators are

designed to work ONLY WITH SAMSUNG Water

Filter.

The Filter light turns red to let you

know when it is time to change your

water ﬁ lter cartridge.

To give you time to get a new ﬁ lter,

the red light comes on just before the

capacity of the current ﬁ lter runs out.

Changing the ﬁ lter on time provides you with the

freshest, cleanest water from your refrigerator.

Shut off the water supply. Then, turn the water 1.

ﬁ lter ( 1 ) about 1/4 turn, counter-clockwise.

Pull the water ﬁ lter ( 2. 1 ) from the case ﬁ lter ( 2 ).

• To change the water ﬁ lter more easily,

shut off the water supply valve.

Sometimes, it is hard to disassemble the water •

ﬁ lter because impurities in the water cause it

to stick. If you are having difﬁ culties, grip the

water ﬁ lter ﬁ rmly and pull it hard.

WARNING

When you pull the •

water ﬁ lter, a little

water can leak from

the opening. This is

normal. To minimize

the water leaks, keep the ﬁ lter cartridge

horizontal when you pull it.

To prevent overﬂ ow, empty the water ﬁ lter tray •

( 3 ) and dry around the ﬁ lter case ( 2 ).

Insert the new ﬁ lter into the ﬁ lter case ( 3. 4 ).

Push the ﬁ lter, and then turn it clockwise until it 4.

locks.

• If you have trouble inserting the water

ﬁ lter because of high water pressure,

shut off the water supply valve.

The locked symbol should be lined up •

with the indicator line.

Touch the 5. “

Ice Type/Water

Hold 3 sec for Filter Reset

”

button (

(Filter Reset)

) for

about 3 seconds to reset

the water ﬁ lter. The color of

indicator (

) changes from red to off.

If you turned off the water supply, turn it back 6.

on.

For a replacement water ﬁ lter, you can

visit your local home Improvement center

or contact the Samsung Parts distributor.

Be sure the replacement water ﬁ lter has

the SAMSUNG logo on the box and

on the water ﬁ lter. Link : http://www.

samsungparts.com

(Red)

3

2

4

2

1

operating _17

02 OPERATING

Removing any residual matter inside

the water supply line after installing

the water ﬁ lter.

Turn ON the main water 1.

supply and supply water

from water supply line.

Run water through the 2.

dispenser until the water

runs clear (approx. 6 to

7 minutes). This will clean the water supply

system and remove air from the lines.

Additional ﬂ ushing may be required in some 3.

households.

Open the Refrigerator door and make sure 4.

there are no water leaks coming from the

w

ater ﬁ lter.

Be sure to ﬂ ush the dispenser thoroughly,

otherwise water may drip from the

dispenser.

This means that there is still air in the line.

Reverse Osmosis Water Supply

IMPORTANT:

The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet

valve of the refrigerator needs to be between 241

and 827 kPa.

If a reverse osmosis water ﬁ ltration system is

connected to your cold water supply, the water

pressure to the reverse osmosis system needs

to be a minimum of 276 to 414 kPa. If the water

pressure to the reverse osmosis system is less

than 276 to 414 kPa:

Check to see whether the sediment ﬁ lter in the •

reverse osmosis system is blocked. Replace

the ﬁ lter if necessary.

Allow the storage tank on the reverse osmosis •

system to reﬁ ll after heavy usage.

If your refrigerator has a water ﬁ lter, it may •

further reduce the water pressure when used

in conjunction with a reverse osmosis system.

Remove the water ﬁ lter.

If you have questions about your water pressure,

call a licensed, qualiﬁ ed plumber.

CONTROLLING THE TEMPERATURE

Basic temperature of Freezer and

Refrigerator Compartments

The basic temperature and recommended

temperatures of the Freezer and Refrigerator

Compartments are 0 °F and 37 °F(or -18 °C

and 3 °C) respectively. If the temperature of the

Freezer and Refrigerator Compartments are too

high or low, adjust the temperature manually.

Controlling the Freezer

temperature

The Freezer temperature can be set between -8 °F

and 5 °F (or between -23 °C and -15 °C) to suit

your particular needs. Press the Freezer button

repeatedly until the desired temperature is shown

in the temperature display. The temperature will

change by 1 °F (or 1 °C) with each press. See

below.

Fahrenheit : 0 °F

➞

-1 °F

➞

-2 °F

➞

-3 °F

➞

-4 °F

➞

-5 °F

➞

-6 °F

➞

-7 °F

➞

-8 °F

➞

5 °F

➞

4 °F

➞

3 °F

➞

2 °F

➞

1 °F

➞

0 °F.

Centigrade : -18 °C

➞

-19 °C

➞

-20 °C

➞

-21 °C

➞

-22 °C

➞

-23 °C

➞

-15 °C

➞

-16 °C

➞

-17 °C

➞

-18 °C.

Keep in mind that foods like ice cream may melt

at 4 °F (or -15.5 °C). The temperature display

will move sequentially from -8 °F to 5 °F (or from

-23 °C to -15 °C).

Controlling the fridge temperature

The fridge temperature can be set between 34 °F

and 44 °F (or between 7 °C and 1 °C) to suit

your particular needs. Press the Fridge button

repeatedly until the desired temperature is shown

in the temperature display. The temperature will

change by 1 °F (or 1 °C) with each press. See

below.

Fahrenheit : 37 °F

➞

36 °F

➞

35 °F

➞

34 °F

➞

44 °F

➞

43 °F

➞

42 °F

➞

41 °F

➞

40 °F

➞

39 °F

➞

38 °F

➞

37 °F.

Centigrade : 3 °C

➞

2 °C

➞

1 °C

➞

7 °C

➞

6 °C

➞

5 °C

➞

4 °C

➞

3 °C.

The temperature control process for the Fridge

works just like the Freezer process. Press the

Recommend Temp (Freezer) : 0 °F (or -18 °C )

18_ operating

check the

water level

Test button

Fridge button to set your desired temperature.

After a few seconds, the Fridge will begin

adjusting towards the newly set temperature. This

will be reﬂ ected in the digital display.

- The temperature of the Freezer, Fridge

or Cool Select Pantry Zone may rise

when you open the doors too frequently,

or if a large amount of warm or hot food

is placed inside.

This may cause the digital display to blink. -

Once the Freezer and Fridge temperature

return to their normal set temperatures, the

blinking will stop.

If the blinking continues, you may need to -

“reset” the Refrigerator. Try unplugging the

appliance, wait for around 10 minutes and then

plug the power cord back in.

If there is a communication error between the -

Display and Main Controller, the Convertible

Display light may blink. If the blinking continues

for a long period of time, please contact a

Samsung Electronics Service Center.

USING THE COLD WATER

DISPENSER

Push the appropriate ice type

button to select what you want

dispensed.

Using the ice Dispenser

Place a glass underneath the ice

dispenser and push gently against the

dispenser lever with your glass.

Make sure the glass is in line with

the dispenser to prevent the ice from

bouncing out.

Please wait 2 seconds before removing the

glass under the dispenser to prevent spills.

If the Refrigerator door opens, the

Dispenser does not work.

When Cubed Ice is selected after using

the Crushed Ice mode, a small amount of

residual crushed ice might be produced.

Do not pull the lever out. You could damage

or break the lever’s spring.

To clean the ice bin/bucket, wash with a mild •

detergent, rinse well, and dry thoroughly it. Do

not use harsh or abrasive cleaners or solvents.

When you select Cubed Ice after using the •

Crushed Ice mode, a small amount of residual

crushed ice might be produced.

The ice cubes generated by the rapid ice •

making process will look white, which indicates

they are generated normally.

As the ice maker in the refrigerator room •

makes ice cubes even faster, move the ice

cubes from the refrigerator ice bin to the

freezer ice bin if you need more ice cubes.

(only for RF263TE***)

If ice doesn’t come out, pull out the ice bucket •

and press the test button located on the right

side of ice maker.

Do not press the test button continuously •

when the tray is ﬁ lled with ice or water. Water

may overﬂ ow or ice may jam the bucket.

Normal Use•

To ﬁ ll the ice bucket to maximum capacity after

installation, follow these steps:

Water may overﬂ ow or ice may jam the bucket.

CAUTION

NO ICE

Select this if you want to

turn ice maker off

Recommend Temp (Fridge) : 37 °F (or 3 °C )

operating _19

02 OPERATING

dispenser, the ice cubes may clump together.

Remove bucket as arrow direction. Throw away

the ice cubes or clumped ice. Push the bottom of

the bucket until you hear a click. When the bucket

does not ﬁ t, turn the helix by 90 degree and degree

and try again.

Use only the ice maker provided with

the refrigerator. The water supply to

this refrigerator must only be installed/

connected by a suitably qualiﬁ ed person.

Connect to a potable water supply only.

To operate the ice maker properly, water pressure

of 138~862 kPa is required.

If you have a long vacation or business trip and

won’t use the water or ice dispensers for a long

time:

Close the water valve. Otherwise, water -

leakage may occur.

Remove all food. -

Unplug the refrigerator. -

Wipe excess moisture from inside and leave -

the doors open. Otherwise, odor and mold

may develop. Do not put your ﬁ ngers, hands

or any other unsuitable objects in the chute or

ice-maker bucket.

It may result in personal injury or material -

damage. Never put your ﬁ nger or any other

objects in the dispenser opening.

It may cause injury. -

Do not try to disassemble the ice maker.

Do not wash or spray the ice bucket with water

while it is in the refrigerator. Remove it to clean

it.

When you insert the Ice maker tray, be

sure that the tray is well centered at the

entrance.

Otherwise, the tray may be stuck.

Water clouding phenomenon

All water provided to the refrigerator ﬂ ows

through the core ﬁ lter which is an alkaline

water ﬁ lter. In the ﬁ ltering process, the

pressure of the water that has ﬂ owed out

of the ﬁ lter is increased, and the water

becomes saturated with oxygen and

nitrogen. When this water ﬂ ows out into

the air, the pressure plummets and the

oxygen and nitrogen get supersaturated,

which results in gas bubbles. The water

may temporarily look misty or cloudy due

to these oxygen bubbles. After a few

seconds, the water will look clear.

CAUTION

Allow your refrigerator to operate and cool 1.

down for 24 hours (or 1 full day).

Waiting 24 hours will allow your ice maker to -

cool properly.

Dispense 4 to 6 ice cubes into the glass.2.

After 8, and then 16 hours, dispense a full 3.

glass of ice.

When you press the Test button, you will hear •

the refrigerator chime (ding-dong). When the

chime sounds, release the Test button.

The chime sounds automatically again to let •

you know the ice maker is working well.

If you want to remove the ice cubes without

using the ice bucket, please turn the ice

maker o. (However, remove the front

cover from the ice maker.) The ice cubes in

the ice maker can spill out over the drawer.

Do not put food in the ice bucket. If you store

food in the ice bucket, the food may get in the

way of the ice maker while opening/closing

the door, causing damage to the ice maker.

Note that the ice cubes in the ice bucket

may spill out over the drawer when

removing the ice bucket from the drawer.

If this is the case, be sure to clear the ice

cubes that spilled out of the drawer.

If a power failure occurs, ice cubes may

melt then freeze together when the power

comes back on, causing the dispenser to

be out of order.

To prevent this problem, after a power failure, pull

out the ice bucket and discard the residual ice or

water.

If you use all the ice at once, you must

repeat Steps 2 and 3 on the previous page.

However, only wait 8 hours before dispensing the

ﬁ rst 4 to 6 ice cubes. This will replenish the ice

cubes and ensure maximum ice production.

Using the ice o Function

When you select the Ice O mode, remove all ice

cubes from the bucket. If you are not using the ice

CAUTION

20_ operating

PARTS AND FEATURES

Use this page to become more familiar with the parts and features of the refrigerator

When closing the door, make sure the Vertical Hinged Section is in the correct position to avoid

scratching the other door.

If the Vertical Hinged Section is reversed, put it back to the right position and close the door.

Moisture may appear at times on the Vertical Hinged Section.

The door handle may become loose over time. If this happens, tighten the bolts found on the

inside of the door.

If you close one door with a lot of force, the other door may open.

When the door opens, the interlock switch automatically turns o the auger motor in the ice

maker for safety reasons.

When the interior or exterior LED lamp has gone out, please contact your service agents.

Please wait 1 second before removing

the cup after dispensing water to prevent

spills. Do not pull out the lever dispenser

after dispensing ice or water. It comes

back automatically. Ice is made in cubes.

When you select “Crushed”, the ice maker

grinds the ice cubes into crushed ice.

Door Closer

Door Bins

Cool Select

Pantry

PLUS

Light

Vertical Hinged

Section

Vegetable &

Fruit Drawers

Slide-Shelf

FZ Ice-Maker (only for RF263TE***)

Light

Ice Bucket

Auto Pull Out

Drawer

Freezer

Drawer Bin

FF Ice-Maker

Foldable-Shelf

Quick-Space

Glass Shelf

Страница загружается...

Samsung RF263BEAESG Инструкция по применению

Похожие модели бренда

Модели других брендов