Samsung RF62HEPN Инструкция по эксплуатации

English

Refrigerator

user manual

imagine the possibilities

Thank you for purchasing a Samsung product.

To receive a more complete service,

please register your product at

www.samsung.com/register

Free Standing Appliance

02_ safety information

SAFETY INFORMATION

• Before operating the appliance, please read this

manual thoroughly and retain it for your reference.

• Use this appliance only for its intended purpose

as described in this instruction manual. This

appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

• Warnings and Important Safety Instructions in this

manual do not cover all possible conditions and

situations that may occur. It is your responsibility

to use common sense, caution, and care when

installing, maintaining, and operating your

appliance.

• Because these following operating instructions

cover various models, the characteristics of your

freezer may differ slightly from those described in

this manual.

Important safety symbols and

precautions:

WARNING

Hazards or unsafe practices that may

result in severe personal injury or

death.

CAUTION

Hazards or unsafe practices that may

result in minor personal injury or

property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions carefully.

Unplug the power plug from the wall

socket.

Make sure the machine is grounded to

prevent electric shock.

Call the contact center for help.

Note.

These warning signs are here to prevent injury to

you and others.

Please follow them explicitly.

After reading this section, keep it in a safe place

for future reference.

CE Notice

This product has been determined to be in

compliance with the Low Voltage Directive

(2006/95/EC), the Electromagnetic Compatibility

Directive (2004/108/EC) and the Eco-Design

Directive(2009/125/EC) implemented by Regulation

(EC) No 643/2009 of the European Union.

SEVERE WARNING SIGNS

FOR TRANSPORTATION AND

SITE

• When transporting and installing the

appliance, care should be taken to ensure

that no parts of the refrigerating circuit are

damaged.

- Refrigerant leaking from the pipe work could

ignite or cause an eye injury. If a leak is detected,

avoid any naked ﬂ ames or potential sources of

ignition and air the room in which the appliance is

standing for several minutes.

• In order to avoid the creation of a ﬂ ammable

gas-air mixture if a leak in the refrigerating

circuit occurs, the size of the room in which the

appliance may be sited depends on the amount

of refrigerant used.

• Never start up an appliance showing any signs

of damage. If in doubt, consult your dealer. The

room where the refrigerator will be sited must

be 1m³ in size for every 8g of R600a refrigerant

inside the appliance. The amount of refrigerant

in your particular appliance is shown on the

identiﬁ cation plate inside the appliance.

SEVERE WARNING SIGNS

FOR INSTALLATION

• Do not install the refrigerator in a damp

place or place where it may come in

contact with water.

- Deteriorated insulation of electrical parts may

cause an electric shock or ﬁ re.

• Do not place this refrigerator in direct sunlight or

expose to the heat from stoves, room heaters or

other appliance.

• Do not plug several appliances into the same

multiple power board.

The refrigerator should always be plugged into

its own individual electrical which has a voltage

safety information

WARNING

safety information _03

rating that matched the rating plate.

- This provides the best performance and also

prevents overloading house wiring circuits, which

could cause a ﬁ re hazard from overheated wires.

• If the wall socket is loose, do not insert the power

plug.

- There is a risk of electric shock of ﬁ re.

• Do not use a cord that shows cracks or abrasion

damage along its length or at either end.

• Do not bend the power cord excessively or place

heavy articles on it.

• Do not use aerosols near the refrigerator.

- Aerosols used near the refrigerator may cause an

explosion or ﬁ re.

• This refrigerator must be properly installed

and located in accordance with the manual

before it is used.

• Connect the power plug in proper position with

the cord hanging down.

- If you connect the power plug upside down, wire

can get cut off and cause ﬁ re or electric shock.

• Make sure that the power plug is not squashed

or damaged by the back of the refrigerator.

• When moving the refrigerator, be careful not to

roll over or damage the power cord.

- This constitutes a ﬁ re hazard.

• The appliance must be positioned so that the

plug is accessible after installation.

• The refrigerator must be grounded.

- You must ground the refrigerator to

prevent any power leakages or electric

shocks caused by current leakage from

the refrigerator.

• Never use gas pipes, telephone lines or other

potential lightening rods as ground.

- Improper use of the ground plug can result in

electric shock.

• If the power cord is damaged, have it

replaced immediately by the manufacturer

or its service agent.

• The fuse on the refrigerator must be changed by

a qualiﬁ ed technician or service company.

- Failing to do so may result in electric shock or

personal injury.

CAUTION SIGNS FOR

INSTALLATION

• Keep ventilation opening in the appliance

enclosure or mounting structure clear of

obstruction.

• Allow the appliance to stand for 2 hours after

installation.

SEVERE WARNING SIGNS

FOR USING

• Do not insert the power plug with wet

hands.

• Do not store articles on the top of the appliance.

- When you open or close the door, the articles

may fall and cause personal injury and/or material

damage.

• Do not put items ﬁ lled with water on the

refrigerator.

- If spilled, there is a risk of ﬁ re or electric shock.

• Do not let children hang on the door.

- Failure to do so may cause serious personal

injury.

• Do not leave the doors of the refrigerator open

while the refrigerator is unattended and do not let

children enter inside of the refrigerator.

- There is a risk of children entrapment and serious

personal injury because of low temperature.

• Never put ﬁ ngers or other objects into the

dispenser hole.

- Failure to do so may cause personal injury or

material damage.

• Do not store volatile or ﬂ ammable substances

such as benzene, thinner, alcohol, ether or LP

gas in the refrigerator.

- The storage of any of such products may cause

explosions.

• Do not store low temperature-sensitive

pharmaceuticals products, scientiﬁ c materials or

other low temperature-sensitive products in the

refrigerator.

- Products that require strict temperature controls

must not be stored in the refrigerator.

• Do not place or use electrical appliance inside

the refrigerator, unless they are of a type

recommended by the manufacturer.

• Do not use a hair dryer to dry the inside of the

refrigerator. Do not place a lighted candle in the

refrigerator for removing bad odors.

- This may result in electric shock or ﬁ re.

• Do not touch the inside walls of the freezer or

products stored in the freezer with wet hands.

- This may cause frostbite.

• Do not use mechanical devices or any other

means to accelerate the defrosting process, other

than those recommended by the manufacturer.

• Do not damage the refrigerant circuit.

• This product is intended only for the

storage of food in a domestic environment.

• Bottles should be stored tightly together so that

they do not fall out.

• If a gas leak is detected, avoid any naked ﬂ ames

or potential sources of ignition and air the room

in which the appliance is standing for several

CAUTION

WARNING

04_ safety information

minutes.

• Use only the LED Lamps provided by

manufacturer or service agents.

• Children should be supervised to ensure that they

do not play with and/or climb into the appliance.

• Do not disassemble or repair the

refrigerator by yourself.

- You run risk of causing a ﬁ re, malfunction and/

or personal injury. In case of malfunction, please

contact your service agents.

• If the appliance generates a strange noise,

a burning or smell or smoke, unplug the

power plug immediately and contact your

nearest service center.

- Failing to do so may result in electric or ﬁ re

hazards. Keep ventilation opening in the

appliance enclosure or mounting structure clear

of obstruction.

• If you experience difﬁ culty when changing the

light, contact service agents.

• If the products equipped with LED Lamp, do

not disassemble Lamp Cover and LED Lamp by

yourself.

- Please contact your service agents.

• If any dust or water is in refrigerator, pull

out power plug and contact your Samsung

Electronics service center.

- There is a risk of ﬁ re.

CAUTION SIGNS FOR USING

• To get best performance of product,

- Do not place foods too closely in front of

the vents at the rear of the appliance as

it can obstruct free air circulation in the

refrigerator compartment.

- Wrap the food up properly or place it in airtight

containers before put it into the refrigerator.

• Do not place carbonated or ﬁ zzy drinks in the

freezer compartment. Do not put bottles or glass

containers in the freezer.

- When the contents freeze, the glass may break

and cause personal injury and property damage.

• Do not change the functionality of or modify the

refrigerator.

- Changes or modiﬁ cations may result in personal

injury and/or property damage. Any changes or

modiﬁ cations performed by a 3rd party on this

completed appliance is neither covered under

Samsung warranty service, nor is Samsung

responsible for safety issues and damages that

result from 3rd party modiﬁ cations.

• Do not block air holes.

- If the air holes are blocked, especially with a

plastic bag, the refrigerator can be over cooled. If

this cooling period lasts too long, the water ﬁ lter

may break and cause water leakage.

- Do not put any newly introduced food for freezing

near to already food.

• Please observe maximum storage times and

expiry dates of frozen goods.

• Fill water tank, ice tray, water cubes only with

potable water.

• Use only the ice maker provided with the

refrigerator.

• The water supply to this refrigerator must only be

installed/connected by a suitably qualiﬁ ed person

and connect to a potable water supply only.

• In order to operate the ice maker properly, water

pressure of 138 ~ 862kpa(1.4~8.8kgf/cm

3

) is

required.

CAUTION SIGNS

FOR CLEANING AND

MAINTENANCE

• Do not directly spray water inside or

outside the refrigerator.

- There is a risk of ﬁ re or electric shock.

• Do not spray inﬂ ammable gas near the

refrigerator.

- There is a risk of explosion or ﬁ re.

• Do not spray cleaning products directly on the

display.

- Printed letters on the display may come off.

• Remove any foreign matter or dust from the

power plug pins. But do not use a wet or damp

cloth when cleaning the plug, remove any foreign

material or dust from the power plug pins.

- Otherwise there is a risk of ﬁ re or electric shock.

• Never put ﬁ ngers or other objects into the

dispenser hole and ice chute.

- It may cause personal injury or material damage.

• Unplug the refrigerator before cleaning and

performing maintenance.

SEVERE WARNING SIGNS

FOR DISPOSAL

• Ensure that none of the pipes on the back

of the appliance are damaged prior to

disposal.

• R600a or R134a is used as a refrigerant. Check

the compressor label on the rear of the appliance

or the rating label inside the refrigerator to see

which refrigerant is used for your refrigerator.

When this product contains ﬂ ammable gas

(Refrigerant R600a), contact your local authority

CAUTION

WARNING

safety information _05

in regard to safe disposal of this product.

Cyclopentane is used as a insulation blowing gas.

The gases in insulation material require special

disposal procedure. Please contact your local

authorities in regard to the environmentally safe

disposal of this product. Ensure that none of the

pipes on the back of the appliances are damaged

prior to disposal. The pipes shall be broke in the

open space.

• If the appliance contains iso-butane refrigerant

(R600a), a natural gas with high environmental

compatibility that is, however, also combustible.

When transporting and installing the appliance,

care should be taken to ensure that no parts of

the refrigerating circuit are damaged.

• When disposing of this product or other

refrigerators, remove the door/door seals, door

latch so that small children or animals cannot

become trapped inside. Leave the shelves in

place so that children may not easily climb inside.

Children should be supervised to ensure that they

do not play with the old appliance.

• Please dispose of the packaging material for this

product in an environmentally friendly manner.

ADDITIONAL TIPS FOR

PROPER USAGE

• In the event of a power failure, call the local ofﬁ ce

of your Electricity Company and ask how long it

is going to last.

- Most power failures that are corrected within

an hour or two will not affect your refrigerator

temperatures. However, you should minimize the

number of door openings while the power is off.

- Should the power failure last more than 24 hours,

remove all frozen food.

• If keys are provided with the refrigerator, the keys

should be kept out of the reach of children and

not in vicinity of the appliance.

• The appliance might not operate consistently

(possibility of temperature becoming too warm

in refrigerator) when sited for an extended period

of time below the cold end of the range of

temperature for which the refrigerating appliance

is designed.

• Do not store food which spoils easily at low

temperature, such as bananas, melons.

• Your appliance is frost free, which means there is

no need to manually defrost your appliance, as

this will be carried out automatically.

• Temperature rising during the defrost can comply

with ISO requirement. But if you want to prevent

an undue rise in the temperature of the frozen

food while defrosting the appliance, please wrap

the frozen food in several layers of newspaper.

• Any increase in temperature of frozen food during

defrosting can shorten its storage life.

Saving Energy Tips

- Install the appliance in a cool, dry room with

adequate ventilation.

Ensure that it is not exposed to direct sunlight

and never put it near a direct source of heat

(radiator, for example).

- Never block any vents or grilles on the appliance.

- Allow warm food to cool down before placing it in

the appliance.

- Put frozen food in the refrigerator to thaw.

You can then use the low temperatures of the

frozen products to cool food in the refrigerator.

- Do not keep the door of the appliance open for

too long when putting food in or taking food out.

The shorter time for which the door is open, the

less ice will form in the freezer.

- Clean the rear of the refrigerator regularly. Dust

increases energy consumption.

- Do not set temperature colder than necessary.

- Ensure sufﬁ cient air exhaust at the refrigerator

base and at the back wall of the refrigerator.

Do not cover air vent openings.

- Allow clearance to the right, left, back and top

when installing.

This will help reduce power consumption and

keep your energy bills lower.

contents

SETTING UP YOUR FREEZER ………………………………………………………………………………… 06

OPERATING YOUR SAMSUNG REFRIGERATOR …………………………………………………………… 15

TROUBLESHOOTING …………………………………………………………………………………………… 19

06_ setting up06_ setting up

GETTING READY TO INSTALL

THE REFRIGERATOR

Congratulations on your purchase of this Samsung

Refrigerator. We hope you enjoy the state-of-art

features and efﬁ ciencies that this new appliance

offers.

Selecting the best location for the

Refrigerator

• A location with easy access to the water supply.

• A location without direct exposure to sunlight.

• A location with level (or nearly level) ﬂ ooring.

• A location with enough space for the Refrigerator

doors to open easily.

• Allow sufﬁ cient space to the right, left, back and

top for air circulation. If the Refrigerator does not

have enough space, the internal cooling system

may not work properly.

• Please ensure that appliance can be moved freely

in the event of maintenance & service.

First thing! Make sure that you can easily move

your Refrigerator to its ﬁ nal location by measuring

doorways (both width and height), thresholds,

ceilings, stairways, etc.

• Allow clearance to the right, left, back and

top when installing. This will help reduce

power consumption and keep your energy

bills lower.

• If you install the Refrigerator where is below 10ºC,

it may not function in optimum level.

• Do not locate the refrigerator where the wet

condition.

When moving your refrigerator

To prevent ﬂ oor damage be sure the front

leveling legs are in the up position(above the

ﬂ oor). Refer to ‘Adjusting the doors’ in the

manual (on page 13)

FLOORING

For proper installation, this refrigerator must be

placed on a level surface of hard material that is the

same height as the rest of the ﬂ ooring. This surface

should be strong enough to support a fully loaded

refrigerator, or approximately 106kg.

To protect the ﬁ nish of the ﬂ ooring, cut a large

section of the cardboard

carton and place under

the refrigerator where

you are working. When

moving the refrigerator,

be sure to pull it straight

out and return it to

position by pushing it

straight in.

INSTALLATION OF THE WATER

LINE (AUTO ICE MAKER

MODEL)

Before you install the water line

• The water line installation is not warranted by the

refrigerator manufacturer.

So before you install the water line, read the

whole steps for installing and follow these

instructions carefully to minimize the risk of

expensive water damage.

• Banging pipes (water banging in the pipes) in

house plumbing can cause damage to fridge

parts and lead to water leakage or ﬂ ooding. Call

a qualiﬁ ed plumber to correct the problem before

installing the water supply line to the fridge.

setting up your freezer

150mm

100mm

150mm

100mm

817mm

RF62* : 1172mm

RF67* : 1222mm

RF62* : 1125mm

RF67* : 1175mm

817mm

665mm

1492mm 1492mm

RF62*:1455mm

RF67*:1505mm

817mm

Drawer-Type

Swing-Type

CAUTION

Flat-blade

screwdriver(-)

Control Lever

setting up _07setting up _07

01 SETTING UP

• The water ﬁ lter must be installed outside the

refrigerator.

It is not provided with your new

refrigerator. The ﬁ lter cartridge (8)

and holder (9) kit can be purchased

from the retailer where you

purchased this refrigerator.

• Do not use copper line.

• Cut the tubing, making sure the

ends are square and clean.

Connect the water line to the fridge

• Connect the plastic line

on the back of your

fridge to the cartridge

holder outlet (fully insert

the plastic line to the

cartridge holder outlet).

• Insert plastic clip to the

cartridge holder inlet and

outlet.

• Turn water on and check

for any leakage.

• You can purchase the necessary ﬁ lter

cartridge at the retailer where you

purchased this refrigerator. Make sure

you buy the SAMSUNG ﬁ lter cartridge

(Replacement cartridge No : DA29-

10105J) to ensure the best performance.

• Water line must be connected to drinkable water

only

• A compression ﬁ tting and nut kit is supplied with

the unit and it is inside the fridge drawer.

• When pushing the Refrigerator back, make sure

you don’t roll over the power cord or water line

(Icemaker supply line)

To use without the water ﬁ lter

section

Connecting to the water supply line

• Shut off the main water

supply line and turn the Ice

maker to the off position.

• Locate the nearest cold

water drinking line.

• To prevent burns and product damage, do not

hook up the water line to the hot water line.

• Do not install the water line in areas where

temperatures fall below freezing.

• When using any electrical device (such as a

power drill) during installation, be sure the device

is insulated or wired in a manner to prevent

electric shock.

• All installations must be in a accordance with

local plumbing code requirements.

• Water line Kit and water ﬁ lter are not

covered by Samsung’s Warranty. The

manufacturer (or dealer, installer) of them is

responsible for any defects and all the loss

caused by water ﬁ lter & water line kit.

• The ﬁ lter should be replaced according to

manufacturer (or dealer)’s instruction.

• To order additional water ﬁ lters, please contact

the manufacturer (or dealer) of the ﬁ lter.

Check the accessories listed

below.

Using the water ﬁ lter (not provided)

Connecting to water supply line

• Shut off the main water

supply line and turn the Ice

maker to the off position.

• Locate the nearest cold

drinking water line.

• Follow the instructions in the

water ﬁ lter installation kit.

• After connecting the water

supply line to the Cartridge

Holder inlet and installing the

Filter Cartridge (insert plastic

line in fully).

• Turn on water supply and

ﬂ ush 3L into a bucket to clear

the water ﬁ lter.

Water line ﬁ xer and screws Pipe connector

Water line Fastner

- Refer to ‘MAKING MINOR

ADJUSTMENTS BETWEEN

DOORS’(on page 14)

Incorrect

Correct

90 degree

1. Cold Water line

2. Pipe Clamp.

3. Plastic line

4. Compression Nut

5. Compression Sleeve

6. Packing Nut

7. Shut Off Valve

8. Filter Cartridge

9. Cartridge Holder

Cartridge Holder

Clip

Filter

cartridge

Plastic line

(Provided)

1. Cold Water line

2. Pipe Clamp.

3. Plastic line

4. Compression Nut

5. Compression Sleeve

6. Packing Nut.

7. Shut Off Valve

08_ setting up08_ setting up

Only connect the water line to a drinkable

water source.

If you have to repair or disassemble the

water line, cut off 6.5mm of the plastic tubing

to make sure you get a snug, leak-free

connection.

After the water supply has been installed

check all the joints to ensure there are no

leaks.

• Samsung Warranty does

not cover THE WATER

LINE INSTALLATION.

• The cost of the water

line installation is at the

customers expense, unless the retailer has

covered this expense in the delivery charge.

• Please contact a Plumber or Authorized Installer

for the installation if needed.

• If Water leakage occurs due to improper

installation, Please contact installer.

SETTING UP THE

REFRIGERATOR

Now that you have your new Refrigerator installed in

place, you are ready to set up and enjoy the features

and functions of the appliance. By completing the

following steps, your Refrigerator should be fully

operational.

1. Place the Refrigerator in an appropriate location

with reasonable clearance between the wall and

the Refrigerator. Refer to installation instructions

in this manual. (P8. Selecting the best location for

the Refrigerator)

2. Once the Refrigerator is plugged in, make sure

the interior light comes on when you open the

doors.

3. Set the Temperature control to the coldest

temperature and wait for an hour. The Freezer

will get slightly chilled and the motor will run

smoothly.

4. After powering the Refrigerator, it will take a few

hours to reach the appropriate temperature. You

can store food and drinks in the Refrigerator after

the temperature is sufﬁ ciently cool.

1. First, shut off the main water supply line.

2. Locate the nearest cold, drinking water line.

3. Follow the Water line Installation Instructions in

the installation kit.

The water line must be connected

to the cold water pipe. If it is

connected to the hot water

pipe, it may cause the puriﬁ er to

malfunction.

CAUTION

Connecting the water line to the

refrigerator

1. Remove the cap from water line on the unit and

insert compression nut to the water line on the

unit after disassembling from provided water line.

2. Connect both water line from the unit and water

line in the kit.

3. Tighten the compression nut onto the

compression ﬁ tting. There should be no gaps

between

(A, B & C )

4. Turn water on and check for any leakage.

Close Main

Water pipe

Close Main

Water pipe

No gap

Remove

cap

Water Line

from unit

Water Line

from unit

No gap

Loosen a

CAUTION

setting up _09setting up _09

01 SETTING UP

REMOVING THE

REFRIGERATOR DOORS

Some installations require door/drawer removal to

transport the Refrigerator to its ﬁ nal location.

Do not remove the door/drawer if it is not needed.

Before removing the door/drawer make sure you

read following items.

Disconnect power to the Refrigerator before

removing the door or drawer.

• Be careful not to drop, damage or scratch

the door/drawer while removing them.

• Be careful not to get injured while removing the

door/drawer.

• Reattach the door/drawer properly to avoid:

- Moisture from air leakage.

- Uneven door alignment.

- Wasting energy due to improper door seal.

Required Tools (Not provided)

Disassembling the fridge door

Be careful not to drop and scratch the fridge door while removing the fridge door!

1. Remove the 3 screws

holding down the top table

and remove it.

2. Disconnect electric wire on

the top of the refrigerator.

3. Remove the 3 hex bolts

that hold the hinge on the

top of the refrigerator with

the 10mm socket wrench.

4. Remove the screw that

holds the ground wire with

a philips screwdriver(+).

5. Separate the hinge from

the electric wire and

ground wire as shown

above.

6. Lift the door straight up to

remove. Be careful not to

drop and scratch the doors

while removing them.

Phillips Head

Driver(+)

Flat Head Driver(-) Socket Wrench

(10mm) (for bolts)

Hex Wrench

(Ø5mm)

(for Mid hinge)

Hex wrench

(5/32 inch)

(for Mid hinge

shaft)

CAUTION

WARNING

Top Table

Socket wrench

10_ setting up10_ setting up

Disassembling the freezer door

1. Separate the cap on the

middle hinge.

2. Remove the screw attached to the left and right middle

hinges with a philips screwdriver(+).

Remove the 2 hex head bolts attached to the left and right

middle hinges with an allen wrench(Ø5mm).

(DRAWER TYPE)

3. After opening the Freezer

door, lift the drawer box.

4. Remove 4 hex head bolts

from both sides with a

socket wrench(10mm)

5. Lift up the freezer door

from the rails. Be careful

not to drop and scratch

the freezer door.

(SWING TYPE)

3. Remove the Middle Hinge

connected to the Freezer.

4. Lift up the freezer door

from the hinge.

Be careful not to drop and

scratch the freezer door.

Reassembleing the door

To reassemble the door, assemble parts in revers oder.

Middle Hinge

CAUTION

setting up _11setting up _11

01 SETTING UP

How to reverse the door (OPTION)

Unplug the refrigerator or disconnect the power.

Refer to the page 9, 10 for disassembling the door.

1. Remove 2 screws.

2. Separate front leg Cover.

3. Separate the Cap of the

front leg Cover. (pull out

inside of Cap)

4. Insert the Cap on the other

side of the front leg Cover.

5. Remove 2 bolts of each

hinge with the 10mm

wrench.

6. Place them in front of each

side.

7. Separate low hinge shaft

by using 5/32” wrench and

disassemble low hinge leg

by turning it colockwise,

and then assemble the low

hinge by turning it over.

8. Reattach the former right

hinge on the left side and

the former left hinge on the

right side by using 2bolts.

9. Separate stopper by

removing 1 screw on the

right lower side of freezer

and assemble the stopper

on the left side by reversing

it.

10. The middle hinge for

reversing a door can be

found in the fridge.

11. Change the middle hinges

assembled at refrigerator

to the middle hinges in the

fridge with handles.

12. Use the black hinge

cap of the middle hinge

assembled at refrigerator.

Then place it at the bottom

of the left middle hinge

supplied separately.

Use the Flat-blade screwdriver(-).

Cap

Cover

Cap

12_ setting up12_ setting up

13. Place the hole in the

bottom of the freezer door

over the low hinge.

14. Replace the middle hinge connected to the freezer.

15. Insert and tighten the screw into the left and right middle

hinges with a philips screwdriver(+). Insert and tighten the 2

hex head bolts into the left and right middle hinges with an

allen wrench(Ø5mm).

16. Replace the cap on the middle hinge.

17. Place the hole in the

bottom of the left door

over the middle hinge.

18. Insert the left upper hinge

shaft into the hole on the

corner of the fridge door.

19. Insert the upper hinges

into the holes at the top of

the door.

Insert and tighten the 3

hex head bolts into the left

and right upper hinges with

a socket wrench(10mm).

20. Insert and tighten the

ground screw into the left

and right upper hinges with

a philips screwdriver(+).

21. Connect the electronic

wire on the top of the

refrigerator.

22. Position the top table in

place. Insert and tighten

the 3 screws into the

top table with a philips

screwdriver(+).

setting up _13setting up _13

01 SETTING UP

ADJUSTING THE DOORS

After putting the doors back on the Refrigerator,

make sure the Refrigerator is level so that you can

make ﬁ nal adjustments.

If the Refrigerator is not level, it will not be possible

to get the doors perfectly even.

Also it is possible to sweat in the refrigerator and ask

more energy bills.

For example, when the left side is lower than the

right side, insert a ﬂ at-blade screwdriver into a notch

on the left control lever, and turn it clockwise or

counter clockwise to level the door.

Turning it clockwise to raise the refrigerator and

counterclockwise to lower it.

For the left side is higher, do it with right lever.

Both control levers must be surely touching

the ﬂ oor to avoid the possible personal injury

or property damage because of tipping.

When the left

side is lower.

When the left

side is higher.

Screwdriver(-)

Control Lever

Screwdriver(-)

CAUTION

14_ setting up14_ setting up

When you turn the hex wrench counter-

clockwise ( ), the door will move up.

Only the left-door height is adjustable for

Swing-Type.

1. After adjusting the doors, please insert the

supplied fastener ( 5 ) using Pliers ( 6 ) in the gap

between the hinge-grommet ( 7 ) and the middle

hinge ( 8 ). The number of fasteners you’ll need to

insert depends on the gap.

2 fastener are enclosed with the refrigerator.

The thickness of each fastener is 1.0mm.

MAKING MINOR ADJUSTMENTS

BETWEEN DOORS

Remember, a level Refrigerator is necessary for

getting the doors perfectly even. If you need

help, review the previous section on leveling the

Refrigerator.

1. Pull out the freezer drawer ( 1 ), then you can see

the middle hinge ( 2 ) .

2. Insert the supplied hex wrench ( 3 ) into the shaft

( 4 ) of the middle hinge.

3. Please adjust the height by turning the hex

wrench ( 3 ) clockwise (

) or counter-

clockwise ( ).

When the left door

is lower than the

right door.

Adjustment

part

When the left door

is higher than the

right door.

Adjustment

part

2

3

4

1

3

operating _15operating _15

02 OPERATING

PARTS AND FEATURES

Use this page to become more familiar with the

parts and features of the Refrigerator.

USING THE CONTROL PANEL

1

Ice Off Button

When the Ice Off button is pressed, ice will not be

produced.

Use this function only when it is needed.

2

Power Freeze

Press the Power Freeze Button. (Refer to the

picture.)

- The power Freeze light on the display goes on

(see the arrow mark) and this function begins to

operate regardless of the set freezer temperature.

Press the Power Freeze Button again to cancel this

function.

- The light goes off and it operates at the set

freezer temperature again.

- The Power Freeze function operates for 72 hours

regardless of the set temperature.

When you use this function, the energy

consumption will increase. This function must

be activated before putting large amount of

food stuff in the freezer compartment at least

48 hours before.

3

Freezer

If you want to control the freezer temperature, follow

as below.

Press the Freezer Button (Refer the picture)

- The temperature can be set in 1ºC interval

between -25ºC and -14ºC.

operating your samsung

refrigerator

Fridge

option

Freezer

Drawer Type Swing Type

1

4

2

5

3

6

16_ operating16_ operating

(Blinking will stop when the refrigerator reaches

normal temperature. If for some reason it does not

stop after a long period of time, contact a Samsung

service center.)

5

Power Cool

Press the Power Cool Button. (Refer to the picture.)

- The Power cool light on the display goes on

(see the arrow mark) and this function begins to

operate regardless of the set fridge temperature.

Press the Power Cool Button again to cancel this

function.

- The light goes off and it operates at the set fridge

temperature again.

The Power Cool function operates for 2 and a

half hours regardless of the set temperature.

6

E.Saver Button

Press the Energy Saver button for better energy

efﬁ ciency. If water drops appear on the doors, turn

the Energy Saver function off.

MAKING ICE

Auto Ice Maker Model

The ice maker will produce 8

cubes per cycle - approximately

100~130 cubes in a 24-hour

period, depending on freezer

compartment temperature,

room temperature, number of

door openings and other use

conditions. Throw away the ﬁ rst few batches of

ice to allow the water line to clear. Be sure nothing

interferes with the sweep of the feeler arm. When the

bin ﬁ lls to the level of the feeler arm, the icemaker

will stop producing ice.

After the icemaker has been turned on again, there

will be a time delay before the icemaker resumes

operation.

It is normal for several cubes to be joined together.

If ice is not used frequently, old ice cubes will

become cloudy, taste stale and shrink. So if you

don’t want to make ice, press the Ice Off button.

When selecting the temperature, the set temperature

is displayed initially for 5 seconds, then the actual

temperature is displayed.

(There may be slight difference between the set

temperature and displayed actual temperature,

but it will be corrected to the set temperature

automatically.)

- The Freezer temperature will change

depending on the number of door

openings, quantity of food, ambient

temperature, etc.

- The temperature display will blink when freezer

temperature increases due to frequent door

opening, keeping warm food, etc.

(Blinking will stop when the refrigerator reaches

normal temperature. If for some reason it does not

stop after a long period of time, contact a Samsung

service center.)

4

Fridge

If you want to control the fridge temperature, follow

as below.

Press the Fridge Button (Refer the picture)

- The temperature can be set in 1ºC interval

between 1ºC and 7ºC.

When selecting the fridge temperature, the set

temperature is displayed initially for 5 seconds, then

the actual temperature is displayed.

(There may be slight difference between the set

temperature and displayed actual temperature,

but it will be corrected to the set temperature

automatically.)

- The Fridge temperature will change

depending on the number of door

openings, quantity of food, ambient

temperature, etc.

- Temperature of each shelve or container in the

fridge may be different.

- The temperature display will blink when fridge

temperature is increases due to frequent door

opening, keeping warm food, etc.

operating _17operating _17

02 OPERATING

3. Vegetable & Fruit Drawers

To remove - Pull the drawer out

to full extension.

Tilt up the front of

the drawer and pull

straight out.

To replace - Insert the drawer

into the frame rails

and push back into

place.

The drawers need to be removed before the

glass shelf above them can be lifted out.

To get the best energy efﬁ ciency of this

product, please leave all selves, drawers

and baskets on their original position like as

illustration in page 15

REMOVING THE FREEZER

ACCESSORIES

1. Pull Out Drawer

To remove - Pull the drawer out to full extension.

Tilt up rear of drawer and lift straight

out. (Refer to picture 1 & 2)

Open the freezer door fully and remove the drawer.

To replace - Place the drawer onto the rails by tilting

it up. Lower the drawer into place until it

is horizontal and slide the drawer in.

(Refer to picture 3)

2. Freezer Drawer Bin

Swing-Type

To remove - Pull the drawer out

fully. Tilt up the rear

of the bin and lift it

out to remove.

To replace - Place the bin into the

rail assembly.

When replacing, place the drawer

bin holder into the hole of the rail

Twist Ice Maker Model

1. Pull out the Ice-cube trays.

2. Fill trays up to the water level mark(arrow).

3. Put the Ice-cube trays back in position. And close

the freezer door.

4. Once the water has become frozen, turn the dials

on the Ice cube trays to empty Ice cubes into the

storage bin.

REMOVING AND RELOCATING

THE FRIDGE ACCESSORIES

1. Door Bins

To remove - Simply lift the bin up

and pull straight out.

To replace - Slide it in above the

desired location and

push down until it

stops.

Injury may occur if the door bins are not ﬁ rmly

inserted. Do not allow children to play with

bins. Sharp corners of the bins may cause

injury.

Empty the bin before adjusting it.

Dust removal method -Remove the guard and wash

in water.

2. Fridge shelves

To remove - When pulling out the

shelf, if it does not

slide out easily, lift it

up slightly and pull

out again.

To replace - When pushing in the shelf, if it does not

slide in easily, lift it up slightly and push

in again.

The Glass shelves are heavy.

Use special care when removing them.

1

2

4

3

CAUTION

1

2

3

1

2

1

2

1

18_ operating18_ operating

Do not put anything other than water in the

water tank.

• Do not put anything other than water in the water

tank.

• Fill with water up to 4.0L. If the water is ﬁ lled up

above the mark, it can spill out when the door

opens and closes.

• Push the cap until you hear a click.

Getting water from the dispenser

Place a glass underneath the water

outlet and push it gently against

the water dispenser lever with your

glass. Blue light will turn on when

you push the lever.

• Make sure the glass is in

line with the dispenser to prevent the water

from splashing out.

• Water dispenser may not be abailable depending

on the model.

When the water dispenser is not in

use, the following is recommended

Fix the water supply device tightly into the ﬁ xing

hole.

The door will not be closed automatically when the

water supply device is pulled out for a long time

because of cold leaking.

CLEANING THE REFRIGERATOR

Do not use Benzene, Thinner or Clorox™ for

cleaning. They may damage the surface of the

appliance and can create a risk of ﬁ re.

Do not spray the refrigerator with water while

it is plugged in, as it may cause an electric

shock. Do not clean the refrigerator with

benzene, thinner or car detergent for risk of

ﬁ r e .

CHANGING THE INTERIOR

LIGHTS

Changing the LED Type Lighting

Do not disassemble or replace the LED type

Lighting.

To change the LED Type Lighting contact Samsung

service center or your authorized Samsung dealer.

Drawer-Type

To remove the drawer - Pull the drawer out fully. Tilt

up the rear of the bin and lift

it out to remove.

To relocate the drawer - Place the bin into the rail

assembly.

Do not allow children to play with the

refrigerator, as they could injure themselves or

damage the refrigerator.

Do not sit on the Freezer door. The door may

break. Do not allow children to climb into the

Freezer basket.

If you remove the divider to clean the basket

bin, you must reinstall the divider using 1

screw after cleaning to prevent children from

getting trapped inside the basket.

USING THE WATER DISPENSER

(OPTION)

You can easily obtain chilled water with the water

dispenser without opening the refrigerator door. In

addition, you can save electricity by reducing the

number of times the door is opened by more than

30%.

Filling the water tank

You can ﬁ ll the water with the water tank sitting

inside of the refrigerator or you can remove the

water tank to ﬁ ll the water.

Method 1

After opening the cap, Fill the water. If you pour the

water too fast, water may overﬂ ow.

Method 2

1. Release the lock on the both side of the water

tank to remove the lid on the water tank.

2. Fill the water in the water tank.

CAUTION

WARNING

(RF67****)

(

)

(

)

Drawer

CAUTION

WARNING

CAUTION

troubleshooting _19troubleshooting _19

04 TROUBLESHOOTING

troubleshooting

PROBLEM SOLUTION

The Refrigerator does

not work at all or it does

not chill sufﬁ ciently.

• Check that the power plug is properly connected.

• Is the temperature control on the display panel set to the correct

temperature?

Try setting it to a lower temperature.

• Is the refrigerator in direct sunlight or located near a heat source?

• Is the back of the refrigerator so close to the wall that air cannot keep

circulating? (Refer to page 10 for the best location.)

The food in the

Refrigerator is frozen.

• Is the temperature control on the display set to the correct

temperature?

Try setting it to a warmer temperature.

• Is the temperature in the room too low?

• Did you store the food too close to the air vent at the back of the

refrigerator? Move the food away from the air vent.

You hear unusual noise

or sounds.

• Check that the refrigerator is level and stable.

• Is the back of the refrigerator too close to the wall and therefore

keeping air from circulating?

• Was anything dropped behind or under the refrigerator?

• A “ticking” sound is heard from inside the refrigerator. It is normal and

occurs because various accessories are contracting or expanding

according to the temperature of the refrigerator interior.

The front corners and

horizontal hinged section

of the appliance are hot

and condensation is

occurring.

• Some heat is normal as anti-condensators are installed in the horizontal

hinged section of the refrigerator to prevent condensation.

• Is the refrigerator door ajar? Condensation can occur when you leave

the door open for a long time.

Ice Maker is not

producing ice.

• Did you wait for 12 hours after installation of the water supply line

before making ice?

• Is the water line connected and the shut-off valve opened?

• Did you manually stop the ice making function?

• Is the freezer temperature too warm? Try setting the freezer

temperature lower.

You hear water bubbling

in the Refrigerator.

• This is normal. The bubbling comes from the refrigerator coolant liquid

circulating through the refrigerator.

There is a bad smell in

the Refrigerator.

• Check for spoiled food.

• Foods with strong odors (for example, ﬁ sh) should be tightly covered.

• Clean out your freezer periodically and throw away any spoiled or

suspicious food.

Frost forms on the walls

of the Freezer.

• Is the air vent blocked? Remove any obstructions so air can circulate

freely.

• Allow sufﬁ cient space between the foods stored for efﬁ cient air

circulation.

• Is the freezer drawer closed properly?

English

Correct Disposal of This Product

(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems)

This marking on the product, accessories or literature indicates that the product and its electronic accessories

(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their

working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,

please separate these items from other types of waste and recycle them responsibly to promote the sustainable

reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government

ofﬁ ce, for details of where and how they can take these items for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of the purchase contract. This

product and its electronic accessories should not be mixed with other commercial wastes for disposal.

In an effort to promote recycling this user manual is printed on recycled paper.

Ambient Room Temperature Limits

This fridge/freezer is designed to operate in ambient temperatures speciﬁ ed by its temperature

class marked on the rating plate.

NOTE: Internal temperatures may be affected by such factors as the location of the fridge/

freezer, ambient temperature and the frequency with which you open the door. Adjust

the temperature as required to compensate for these factors.

Class Symbol Ambient Temperature range(°C)

Extended Temperate SN +10 to +32

Temperate N +16 to +32

Subtropical ST +16 to +38

Tropical T +16 to +43

Страница загружается ...

Samsung RF62HEPN Инструкция по эксплуатации

Это руководство также подходит для

Samsung RF62HEPN Инструкция по эксплуатации

Похожие модели бренда

Модели других брендов