Sony KV-SZ25M91 Инструкция по применению

Trinitron Color TV

KV-SZ29

KV-SZ25

2-682-860-E1 (1)

Operating Instructions

• Before operating the unit, please read this manual thoroughly and retain

it for future reference.

GB

M91

2

WARNING

• Dangerously high voltages are present inside the TV.

• TV operating voltage: 220 – 240 V AC.

• Do not plug in the power cord until you have completed making all other

connections; otherwise a minimum leakage current might flow through the antenna

and other terminals to ground.

• To avoid battery leakage and damage to the remote, remove the batteries from the

remote if you are not going to use it for several days. If any liquid leaks from the

batteries and touches your skin, immediately wash it away with water.

Clean the TV with a dry and soft

cloth. Do not use benzine, thinner,

or any other chemicals to clean the

TV. Do not attach anything (e.g.,

adhesive tape, cellophane tape,

glue) on the painted cabinet of the

TV. Do not scratch the picture

tube.

Install the TV on a stable TV stand

and floor which can support the

TV set weight. Ensure that the TV

stand surface is flat and its area is

larger than the bottom area of the

TV.

Do not plug in too many

appliances to the same power

socket. Do not damage the power

cord.

For children’s safety, do not leave

children alone with the TV. Do not

allow children to climb onto it.

For your own safety, do not touch

any part of the TV, the power cord

and the antenna cable during

lightning storms.

Do not place any objects on the TV.

The apparatus shall not be

exposed to dripping or splashing

and that no objects filled with

liquids, such as vases, shall be

placed on the apparatus.

Do not operate the TV if any liquid

or solid object falls into it. Have it

checked immediately by qualified

personnel only.

Do not block the ventilation

openings of the TV. Do not install

the TV in a confined space, such

as a bookcase or built-in cabinet.

Do not open the cabinet and the

rear cover of the TV as high

voltages and other hazards are

present inside the TV. Refer

servicing and disposal of the TV

to qualified personnel.

Pull the power cord out by the

plug. Do not pull the power cord

itself. Even if your TV is turned

off, it is still connected to the AC

power source (mains) as long as

the power cord is plugged in.

Unplug the TV before moving it

or if you are not going to use it for

several days.

To prevent fire or shock hazard, do

not expose the TV to rain or

moisture.

Your TV is recommended for

home use only. Do not use the TV

in any vehicle or where it may be

subject to excessive dust, heat,

moisture or vibrations.

3

Menu Adjustment

Introducing the WEGA GATE

navigator ............................................. 15

“Settings” Adjustment ...................... 16

Changing the “Picture” setting ........ 17

Changing the “Sound” setting ......... 19

Changing the “Channel Setup”

setting .................................................. 20

Changing the “Setup” setting .......... 22

Additional Information

Connecting optional components ... 23

Troubleshooting ................................. 25

Specifications ...................... Back cover

GB

Table of Contents

Installation

Securing the TV .................................... 4

Getting Started ..................................... 5

Setting up your TV

(“Initial Setup”) .................................... 6

Overview of Controls

TV front and rear panels ..................... 8

Using the remote control and

basic functions ...................................... 9

Advanced Operations

Selecting the picture and sound

modes .................................................. 11

Listening to the FM Radio ................ 12

Enjoying stereo or bilingual

programs ............................................. 13

Viewing Teletext ................................. 14

Made in Malaysia.

Sony Corporation

6-7-35 Kitashinagawa,

Shinagawa-ku, Tokyo, 141-0001 Japan.

4 Installation

Installation

x Securing the TV

To prevent the TV from falling, use the supplied screws, clamps and band to

secure the TV.

Screw the band to the TV stand and to the

provided hole at the rear of your TV.

(1) Put a cord or chain through the clamps.

(2) Screw one clamp to a wall or pillar and

the other clamp to the provided hole at

the rear of your TV.

(1) Attach each end of a cord or chain to

the provided holders at the rear of your

TV.

(2) Securely fix the attached cord or chain

to a wall or pillar using an attachment

which can support the TV set weight.

Note

• Use only the supplied screws. Use of other screws may damage the TV.

or

20 mm

3.8 mm

screws clamps band

Installation

5

Installation

Step 1

Insert the batteries (supplied) into the remote.

Note

• Do not use old or different types of batteries together.

Step 2

Step 3

Step 4

Set up the TV by following the instructions of the

“Начальная настройкa” (“Initial Setup”) menu

(see page 6).

Plug in the power cord, then press ! on the TV to

turn it on.

Note

• The 1 (standby) indicator flashes green for a few seconds

when turning on the TV. This does not indicate a

malfunction.

Connect the antenna cable (not supplied) to 8

(antenna input) at the rear of the TV.

Tips

• Your TV can receive both TV and FM radio signal from the

appropriate connections through the 8 (antenna input)

terminal (see page 23).

• You can also connect your TV to other optional components

(see page 23).

x Getting Started

b

6 Installation

x

Setting up your TV

(“Initial Setup”)

When you turn on your TV for the first time, the “Начальная настройкa”

(“Initial Setup”) menu will appear. You may change the menu language, preset

the TV channels automatically, sort or edit the channels and adjust the picture

position using the buttons on the remote control or TV front panel.

1

Press V or v to select the desired menu

language, then press .

The selected menu language appears.

2

Press V or v to select “Yes”, then press

to preset the channels automatically.

The screen will indicate automatic

presetting is in progress.

After all available channels have been tuned

and stored, the “Program Sorting/Edit”

menu appears automatically on the screen.

To skip automatic channel presetting, select

“No”, then press

.

If the message “No channel found. Please

connect cable/antenna” appears, check your

TV connections, then press

.

3

The “Program Sorting/Edit” menu enables

you to sort and edit the channels.

a) If you wish to keep the channels in the current

condition, press WEGA GATE to exit.

b) Press V or v to select the program

number with the channel you wish to

change. The selected channel will appear

on the screen.

c) If you wish to store the channels in a

different order:

1) Press b to enter sorting mode.

2) Press V or v to select the new program

number position for your selected channel,

then press B.

End

Select

Confirm

Program:

TV System: Auto

01

VHF Low

End

Program Sorting/Edit

01

02

03

04

Off

Sorting mode

PROG

SkipLabel

Off01

Exit

Select

Confirm

Program Sorting/Edit

01

02

03

04

Off

Sorting:

Edit:

PROG

SkipLabel

Exit

Select

Confirm

Select

End

Installation

7

Installation

d) If you wish to edit the channels, press

to change to edit mode.

Press b until the mode that you wish to edit

is highlighted: Label, Skip, (block symbol).

Then press

.

1) To label, press V or v to select the

alphanumeric characters for the label.

Then press

.

2) To skip the program number, press V or v to

select “On”. Then press

.

You can skip this program number when

using PROG +/-.

3) To block unwanted program number,

press V or v to select

. Then press .

e) Repeat step b) to d) if you wish to change other

channels.

Press WEGA GATE to go to the next menu.

4

Press B or b to adjust the bars on the top

and bottom of the menu if they are

slanted, then press

.

“Picture V-Position” menu appears.

5

If the upper and lower bars are not

equally positioned to the top and

bottom of the screen, press V or v to

adjust them, then press

.

If no adjustment is necessary, then press

.

6

To prevent this “Initial Setup” menu from

appearing again when you turn on the TV

by pressing !, press V or v to select “No”,

then press

.

To allow this menu to appear again, select

“Yes”, then press

.

Tip

• You can immediately go to the end of the ”Initial Setup” menu by pressing WEGA GATE.

Exit

Select

Confirm

Exit

Select

Confirm

Exit

Select

Confirm

Select

End

Confirm

Select

End

Confirm

Select

Confirm

8 Overview of Controls

Overview of Controls

x TV front and rear panels

L

R

1

L

Y

C

B

C

R

(MONO) (MONO)

qa

qsqd

qf

2

0

9

2

L(MONO) R

45

PROG

FM

678

1

3

2

L(MONO) R

PROG

FM

WEGA GATE

TV rear panel

TV front panel

Button/Terminal Function Page

1

! Turn off or turn on the TV. 5

2

1 Standby indicator. 5

2

Wake Up indicator. 10

3

Remote control sensor. –

4

PROG +/– Select program number. –

5

2 +/– Adjust volume. –

6

t

Select TV or video input.

23

WEGA GATE menu operations

4,5

, , ,

Select and adjust items. 15

6

Confirm selected items. 15

7

WEGA GATE Display or cancel WEGA GATE menu. 15

8

FM Listen to FM Radio. 12

9

i Headphone jack. –

0

t2 Video input terminal 2. 23

qa

8 Antenna input terminal. 23

qs

T Monitor output terminal. 24

qd

Component video input terminal. 24

qf

t1 Video input terminal 1. 23

9

Overview of Controls

x Using the remote control and basic

functions

Button Description Page

1 ?/1 Turn off temporarily or turn on –

the TV.

2 a Display the TV program. –

3 Jump to last program number –

that has been watched for

at least five seconds.

4 PROG +/–

Select program number. To select –

quickly, press and hold until the

desired program number appears.

5 2 +/– Adjust volume. –

8 Change the picture size: –

“On” (16:9 wide mode), “Off”.

9 Select surround mode options. 19

0

Display on-screen information. –

qa Mute the sound.

–

qd t Select TV or video input. 23

qf 0 – 9 Input numbers. For program –

numbers 10 and above, enter the

second digit within two seconds.

ql Select sound mode options 11

with a 5-Band Graphic

Equalizer display.

w; Select picture mode options. 11

WEGA GATE menu operations

6 Confirm selected items. 15

7 WEGA Display or cancel the

GATE WEGA GATE menu.

qj V, v, B, b Select and adjust items.

qk

RETURN Return to the previous level.

continue

RETURN

WEGA

GATE

TV

1

2

3

4

6

7

8

9

0

5

PROG

A/B

1

2

3

7

4

5

qj

qk

qa

qd

qf

qh

RETURN

WEGA

GATE

6

8

9

0

w;

ql

qg

qs

10 Overview of Controls

Button Description Page

Timer operations

qg Set TV to turn on automatically according to the –

desired period of time (max. of 12 hours).

The indicator on TV lights up amber once

you set the wake up timer.

If no buttons or controls are pressed for more than

one hour after the TV is turned on using the

wake up timer, the TV automatically goes into

standby mode.

qh

Set TV to turn off automatically according to the –

desired period of time (max. of one hour and

30 min.).

Teletext operations (green label)

, , , ,

All buttons are used for Teletext operations. 14

, , , ,

(red, green,

yellow, blue)

PIP operations

, , V, v, B, b Not function for your TV.

–

Stereo/bilingual operations

qs A/B Select stereo/bilingual mode. 13

(Wake up timer)

(Sleep timer)

continued

11

Advanced Operations

Selecting the sound mode

Press to select the desired sound mode. 5-Band Graphic Equalizer display will

appear.

Select To listen to

“Dynamic” dynamic and clear sound that emphasizes both the low

and high tones.

“Standard” sound that emphasizes voice and high tones.

“Custom” the last adjusted sound setting from the

“Sound Adjustment” option in the menu (see page 19).

x Selecting the picture and sound

modes

You can select picture and sound modes and adjust the setting to your

preference in the “Custom” option.

Selecting the picture mode

Press to select the desired picture mode.

Select To view

“Vivid” bright, contrast and sharp

pictures.

“Standard” normal pictures.

“Custom” the last adjusted picture setting

from the “Picture Adjustment”

option in the menu (see page 18).

WEGA

GATE

TV

1

2

3

4

6

7

8

9

0

5

PROG

A/B

WEGA

GATE

RETURN

Dynamic

100 300 1k 3k 8k

Standard

100 300 1k 3k 8k

Custom

12 Advanced Operations

x Listening to the FM Radio

You are able to listen to the FM radio stations using your TV.

To access to FM Radio mode:

Press WEGA GATE button and select “FM Radio” (see page 15).

or

Press FM button on the front panel (see page 8).

To exit from FM Radio mode:

Press WEGA GATE button, select the desired items: “TV” or “External Inputs”,

then press

. Select the desired TV channel or external inputs and press .

or

Press FM button on the front panel.

Listening to non-preset stations

1

Access to FM Radio mode.

2

Press V or v to search for the desired FM radio station. The preset number and

label will not be displayed.

3

If the station has a weak signal, press B or b to fine tune the radio frequency

manually.

Notes

• You can only operate V, v, B and b functions using the remote control buttons in FM

Radio mode.

•

The available radio frequency is only for temporary listening pleasure and cannot be

stored in the memory.

•

If the message “Please setup FM Radio” appears, display the “Channel Setup” menu and

select “FM Radio Setup” to preset the desired FM radio stations (see page 20).

Listening to preset stations

1

Access to FM Radio mode.

2

Press WEGA GATE button and select “Settings”.

Preset the desired FM radio stations in “FM Radio

Setup” from “Channel Setup” menu (see page 20).

3

Exit from “Channel Setup” menu by pressing WEGA

GATE button. The selected preset FM radio station

number and label will appear on the screen.

To select the desired preset FM radio station, press

PROG +/–.

Tip

• You can also use the 1-9 buttons on the remote control to

directly select the desired preset FM radio station.

Note

• When a FM stereo program has static noise, press A/B until “Mono” appears. There will be no

stereo effect, but the noise will be reduced.

A/B

PROG

+/–

V, v,

B, b

WEGA

GATE

TV

1

2

3

4

6

7

8

9

0

5

PROG

A/B

WEGA

GATE

RETURN

13

Advanced Operations

When receiving a NICAM program

Broadcasting On-screen display (Selected sound)

NICAM

stereo

NICAM

bilingual

NICAM

monaural

When receiving an A2 program

Broadcasting On-screen display (Selected sound)

A2

stereo

A2

bilingual

x

Enjoying stereo or bilingual programs

You can enjoy stereo sound or bilingual programs of NICAM and A2 stereo

systems by using the A/B button.

NICAM

(Stereo sound)

Mono

(Regular sound)

t

NICAM Main

(Main sound)

NICAM Sub

(Sub sound)

Mono

(Regular sound)

tt

t

Mono

(Regular sound)

Stereo

(Stereo sound)

t

Main

(Main sound)

Sub

(Sub sound)

t

NICAM Main

(Main sound)

Mono

(Regular sound)

t

Note

• If the stereo sound is noisy when receiving a stereo program, select “Mono”. The sound

becomes monaural, but the noise is reduced.

TV

1

2

3

4

6

7

8

9

0

5

PROG

A/B

RETURN

WEGA

GATE

A/B

14 Advanced Operations

x Viewing Teletext

Some TV stations broadcast an information service called Teletext which allows

you to receive various information, such as stock market reports and news.

You can use the buttons on the remote to view Teletext.

To Do this

display a Teletext Press . Each time you press , the

page on the screen changes as follows:

TV picture Teletext t Teletext and TV t TV.

If there is no Teletext broadcast, “100” is

displayed at the top left corner of the

screen.

check the contents Press .

of a Teletext service An overview of the Teletext contents,

including page numbers, appears on the

screen.

select a Teletext page Press the number buttons to enter the

three-digit page number of the desired

Teletext page. If you make a mistake,

reenter the correct page number. To

access the next or previous page, press

or .

hold (pause) a Press to display the symbol “ ” at

Teletext display the top left corner of the screen. To

resume normal Teletext viewing, press

.

reveal concealed Press .

information (e.g., To conceal the information, press the

an answer to a quiz) button again.

enlarge the Teletext Press . Each time you press , the

display Teletext display changes as follows:

Enlarge upper half t Enlarge lower

half t Normal size.

stand by for a Teletext (1) Enter the Teletext page number that

page while watching you want to refer to, then press .

a TV program (2) When the page number is displayed,

press to show the text.

select a FASTEXT Press (red, green, yellow and blue)

menu or the colored that corresponds to the desired menu or

boxes page number.

turn off Teletext Press a.

Note

• The FASTEXT feature can be used only when the FASTEXT broadcast is available.

(red,

green,

yellow,

blue)

RETURN

WEGA

GATE

TV

1

2

3

4

6

7

8

9

0

5

PROG

A/B

WEGA

GATE

TV

1

2

3

4

6

7

8

9

0

5

PROG

A/B

,

WEGA

GATE

RETURN

15

Menu Adjustment

x Introducing the WEGA GATE

navigator

WEGA GATE is a gateway that allows you access to preset TV channels,

connected external inputs, FM Radio mode and “Settings” menu.

Confirm

Select

WEGA GATE

Settings

External Inputs

FM Radio

TV

01

02

03

04

05

TV

Confirm

Select

End

Preset 1:

---.--

Please setup FM Radio

FM Radio

Select Preset 1-9

Search

Exit

External Inputs

Confirm

Select

End

Video 1

1

2

Video 2

Confirm

End

Picture

Color Temperature: Cool

Picture Adjustment

Picture Mode: Vivid

VM: High

Intelligent Picture: On

Signal Level Indicator: On

Select

Fine

–PROG+

DVD

01

02

03

04

05

TV

Confirm

Select

End

Confirm

Select

WEGA GATE

Settings

External Inputs

TV

FM Radio

01

02

03

04

05

TV

Confirm

Select

End

How to use WEGA GATE

(1) Press WEGA GATE to display or cancel

the WEGA GATE menu.

Confirm

Select

WEGA GATE

Settings

External Inputs

TV

FM Radio

(3) Press V or v to select the desired item.

(4) Press RETURN to move to the previous

level.

(2) Press (or b) to confirm your selection

or go to the next level.

Tip

• The WEGA GATE, and

, , ,

buttons on the front panel can also be used for the

operations above.

watch the preset TV

channels (see page 6)

select the inputs for the

connected equipment

(see page 23)

change the settings

of your TV

(see page 16)

“TV”

“External Inputs”

“Settings”

“FM Radio”

listen to the FM Radio

(see page 12)

16 Menu Adjustment

x “Settings” Adjustment

You are able to change the settings of your TV from “Settings” in WEGA GATE

menu.

Press WEGA GATE button to display WEGA GATE menu. Press V or v to select

“Settings” and press

.

The following is an overview of the items that can be adjusted.

Confirm

End

Picture

Picture Adjustment

Picture Mode: Vivid

Select

Color Temperature: Cool

VM: High

Intelligent Picture: On

Signal Level Indicator: On

“Picture” (see page 17)

“Picture Mode”: “Vivid” “Standard” “Custom”

“Picture Adjustment”: “Picture”, “Brightness”, “Color”, “Hue”,

“Sharpness”, “Reset”

“Color Temperature”: “Cool” “Neutral” “Warm”

“VM”: “High” “Low” “Off”

“Intelligent Picture”: “On” “Off”

“Signal Level Indicator”: “On” “Off”

Confirm

End

Sound

Sound Adjustment

Sound Mode: Dynamic

Select

Balance

Intelligent Volume:

Surround: Off

Off

“Sound” (see page 19)

“Sound Mode”: “Dynamic” “Standard” “Custom”

“Sound Adjustment”: “Adjust”, “Reset”

“Balance”

“Intelligent Volume”: “On” “Off”

“Surround”: “On” “Simulated” “Off”

“Channel Setup” (see page 20)

“Auto Program”

“Manual Program”

“Program”: “00” - “99”

“TV System”: “B/G” “I” “D/K” “M”

“VHF Low”/“VHF High”/“UHF”

“Fine”: “Auto” “Manual”

“Signal Booster”: “Auto” “Off”

“Program Sorting/Edit”

“FM Radio Setup”

“Setup” (see page 22)

“Language”: “English” “Русский” (Russian)

“Picture Position”: “Picture Rotation”, “Picture V-Position”

“Video Label”: “Video Input”, “Label”

“Color System”: “Auto” “PAL” “SECAM” “NTSC3.58”

“NTSC4.43”

“Factory Settings”: “Yes” “No”

Note

• When a feature is dimmed in the menu, it is not selectable.

Confirm

End

Channel Setup

Select

Manual Program

Auto Program

Program Sorting/Edit

FM Radio Setup

Confirm

End

Setup

Select

Picture Position

Language:

Video Label

Color System: Auto

Factory Settings

English

17

Menu Adjustment

x Changing the “Picture” setting

The “Picture” menu allows you to adjust settings below.

1

Press WEGA GATE and select “Settings”.

2

Make sure the “Picture” icon ( ) is

selected, then press

.

3

Press V or v to select the desired item (e.g., “Picture Mode”), then press .

Select To

“Picture Mode” choose either “Vivid”, “Standard” or “Custom”*

(see page 11).

“Color Temperature” adjust white color tint.

Choose either “Cool” (blue tint), “Neutral” (neutral tint) or

“Warm” (red tint).

“VM” sharpen the edges of each object.

(Velocity Modulation) Choose either “High”, “Low” or “Off”.

“Intelligent Picture” optimize picture quality.

Press V or v to select “On”, then press .

To cancel, select “Off”, then press .

“Signal Level Indicator” display the signal level when the “Intelligent Picture” is

functioning.

“Intelligent Picture Signal Level” indicator will be displayed,

followed by picture improvement when you change the

program number or the input mode.

red amber green

(weak) (average) (good)

Press V or v to select “On”, then press .

To cancel, select “Off”, then press . “Intelligent Picture” is still

functioning.

* You can adjust the setting to your personal preference in the “Picture Adjustment”,

“Color Temperature” and “VM” options only when the “Custom” mode is selected

(see page 18).

Confirm

Picture

Color Temperature: Cool

Picture Adjustment

Picture Mode: Vivid

VM: High

Intelligent Picture: On

Signal Level Indicator: On

Select

End

continue

18 Menu Adjustment

Adjusting the “Picture Adjustment” items under “Custom”

mode

1

Press V or v to select either “Picture” (contrast), “Brightness”, “Color”,

“Hue” (color tones) or “Sharpness”, then press

.

Selecting “Reset” will set your TV to the factory settings.

2

Press V,v,B or b to adjust the setting of your selected item, then press .

3

Repeat the above steps to adjust other items.

The adjusted settings will be received when you select “Custom”.

Notes

• “Hue” can be adjusted for the NTSC color system only.

• Reducing “Sharpness” can also reduce picture noise.

continued

19

Menu Adjustment

Adjusting the “Sound Adjustment” items under “Custom”

mode

The 5-Band Graphic Equalizer feature allows you to adjust sound frequency settings

of “Custom” mode in the menu.

1

Make sure that “Adjust” is selected, then press .

Selecting “Reset” will set your TV to the factory settings.

2

Press B or b to select the desired sound frequency, then press V or v to

adjust the setting and press

.

The adjusted settings will be received when you select “Custom”.

Notes

• Adjusting higher frequency will affect higher pitched sound and adjusting lower frequency

will affect lower pitched sound.

• You may display the settings directly by using button on the remote control (see page 9).

x Changing the “Sound” setting

The “Sound” menu allows you to adjust the settings below.

1

Press WEGA GATE and select “Settings”.

2

Press V or v to select the “Sound”

icon (

), then press .

3

Press V or v to select the desired item (e.g., “Sound Mode”), then press .

Select To

“Sound Mode” choose either “Dynamic”, “Standard” or “Custom”*

(see page 11).

“Balance” Press v or B to emphasize the left speaker.

Press V or b to emphasize the right speaker.

“Intelligent Volume” adjust the volume of all program numbers and video inputs

automatically.

Press V or v to select “On”, then press .

To cancel, select “Off”, then press .

“Surround” choose either “On” (surround), “Simulated” (stereo-like

monaural sound) or “Off”.

* You can adjust the setting to your personal preference in the “Sound Adjustment”

option only when the “Custom” mode is selected.

Confirm

End

Sound

Balance

Sound Adjustment

Sound Mode: Dynamic

Intelligent Volume: Off

Surround: Off

Select

20 Menu Adjustment

x C

hanging the “Channel Setup”

setting

The “Channel Setup” menu allows you to adjust settings below.

1

Press WEGA GATE and select “Settings”.

2

Press V or v to select the “Channel Setup”

icon (

), then press .

3

Press V or v to select the desired item (e.g., “Auto Program”), then press .

Select To

“Auto Program” preset channels automatically.

“Manual Program” manually preset desired channels and channels that cannot be

preset automatically (see Presetting channels manually in

page 21).

“Program Sorting/Edit” change the order in which the channels appear on the screen,

label the program number, skip the program number and block

unwanted programs (see step 3 of the section “Initial Setup” in

page 6).

“FM Radio Setup”* preset up to nine FM radio stations.

You can manually preset each FM radio station that can be

received in your area and then store the radio frequency of the

desired FM radio stations.

(1) Press V or v to select the desired FM radio station position,

then press .

(2) Press V or v to search the FM radio stations.

Searching stops automatically when a station is tuned in.

If the station has a weak signal, press B or b to fine tune the

radio frequency manually, then press to store the FM

radio station.

(3) You may edit the FM radio station label. Press V or v to

select alphanumeric characters for the label, then press .

(4) Repeat steps (1) through (3) to preset other FM radio

stations.

*

The “FM Radio Setup” feature is only available in FM Radio

mode. To enable this feature, access to FM Radio mode by

using WEGA GATE system (see page 15) or pressing the FM

button on the front panel (see page 8), then preset your

desired FM radio stations according to the steps mentioned above.

Notes

• If you preset a blocked program number, that program number will be unblocked

automatically.

• If you sort a blocked program, that program will remain blocked.

Confirm

End

Channel Setup

Program Sorting/Edit

FM Radio Setup

Manual Program

Auto Program

Select

Страница загружается...

Sony KV-SZ25M91, KV-SZ29M91 Инструкция по применению

Похожие модели бренда

Модели других брендов