Yamaha DTX-900K Инструкция по применению

Бренд: Yamaha

Модель: DTX-900K

Категория: Музыкальные барабаны

Тип: Инструкция по применению

Это руководство также подходит для

DTX900K

Yamaha DTX-900K дает вам широкие возможности для занятий игрой на барабанах, исполнения и творчества. С помощью этого устройства вы можете:

Улучшить свои навыки игры на барабанах благодаря функциям обучения, встроенному метроному и возможности записи собственной игры.
Играть в любимые песни, подключив устройство к музыкальному проигрывателю или компьютеру.
Создавать собственные музыкальные композиции с помощью встроенного секвенсора и звукового генератора.
Подключить дополнительные пэды и тарелки для расширения возможностей установки.

Улучшить свои навыки игры на барабанах благодаря функциям обучения, встроенному метроному и возможности записи собственной игры.
Играть в любимые песни, подключив устройство к музыкальному проигрывателю или компьютеру.
Создавать собственные музыкальные композиции с помощью встроенного секвенсора и звукового генератора.
Подключить дополнительные пэды и тарелки для расширения возможностей установки.

This manual describes the standard assembly of the DTX900K.

After assembling the parts and connecting the cords as shown below, the Drum Trigger Module is ready to be turned on.

•To assemble the unit, make sure you have the following four pack-

ages: RS130 (Rack System), DTP900 (Pad Set), DTP901(Pad

Set), DTX900 (Drum Trigger Module).

• This manual covers how to attach the Pads and Drum Trigger Mod-

ule to the Rack System RS130, for which assembly has already

been completed. Before performing the instructions described in

this manual, make sure to complete the Rack System RS130 by

following the corresponding Assembly Manual.

Before assembling the unit, lay a drum mat (sold separately) on the

ﬂoor. Alternately, to prevent damaging the ﬂoor, lay the cardboard of

the included packages, etc. on the ﬂoor before handling the Hi-Hat

Stand HS740A and Kick Pad KP125W.

Before using, please read this assembly manual, and use this product in a safe and proper manner.

* Please keep this manual in a safe place for future reference.

* Make sure to read the Assembly Manual of the Rack System and the Owner’s Manual of the Pad.

NOTICE

• Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also,

never place any heavy or sharp objects on the cable. Applying excessive force to the cable may

result in damage to the cable, such as the wires being severed, etc.

• Do not step on or place heavy objects on the product. It may result in damage.

• Do not use or keep the product in places with extremely high temperature (places in direct sunlight,

close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.).

Doing so may result in deformation, discoloration, damage or deterioration.

• When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration

or deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If

the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that

has been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as

not to let the water and detergent come into contact with the cushions used in the product; doing so

may result in deterioration.

* Speciﬁcations and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or speciﬁcations at any time without prior notice. Since speciﬁca-

tions, equipment or options may not be the same in every locale, please check with your Yamaha dealer.

DTX900K

Assembly Manual

PCY155

(Cymbal Pad)

PCY135

(Cymbal Pad)

PCY135

(Cymbal Pad)

XP100T

(Tom Pad)

XP100T

(Tom Pad)

KP125W

(Kick Pad)

CH755

(Cymbal Holder)

CH750

(Cymbal Holder)

RS130

(Rack System)

CH750

(Cymbal Holder)

Drum Trigger

module DTX900

RHH135

(Real Hi-Hat Pad)

HS740A

(Hi-Hat Stand)

SS662

(Snare Stand)

XP120SD

(Snare Pad)

Unit Standard Assembly

IMPORTANT

NOTICE

PRECAUTIONS

If this symbol is ignored and the equipment is used improperly, fatal

injury to persons or serious damage could occur.

• Do not let small children assemble or set up this product by themselves, or they may be injured.

Always assemble this product with adult supervision.

• Be careful with the edges of the Cymbal Holders and the Tom Holders. The sharp holder ends

may result in injury.

• Be careful with the edges of the spurs attached to the Kick Pad and foot pedal. The sharp ends

may result in injury.

• If this product is used with a Rack System or Cymbal Stand, make sure all bolts are tightened

ﬁrmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts

may result in the rack overturning or parts dropping, causing injury.

• Always set the product on a ﬂat and solid surface. Placement on a sloping, unstable surface or on

steps may result in the product being unstable and subject to overturning.

• When setting up the product, please pay close attention to the handling and setting of cables.

Carelessly placed cables may cause the user and others to trip and fall.

• Do not alter the product. Doing so may result in injury or damage/deterioration to the product.

• Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury.

WARNING

If this symbol is ignored and the equipment is used improperly,

there is a danger or injury to persons handling the equipment, and

material damage could occur.

•Watch your ﬁngers when adjusting clamps. They may become pinched, resulting in injury.

• Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your

ﬁngers.

• Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting

in injury.

• Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums

may drop, causing injury.

CAUTION

Assembling the Rack System

For details, refer to the Assembly Manual of the RS130.

Checking the contents of each package

Mounting the Pads and the Drum Trigger Module on the Rack System

Mount the Pads and the Trigger Module on the Rack System. Then position the Kick Pad and the Hi-Hat.

Package 1 [DTP900]

❑ PCY135

(Cymbal Pad) (2)

❑ PCY155

(Cymbal Pad) (1)

❑ RHH135

(Real Hi-Hat Pad) (1)

❑ KP125W

(Kick Pad) (1)

❑ CH750

(Cymbal Holder) (2)

❑ SS662

(Snare Stand) (1)

❑ Stand base for the

RHH135 (1)

❑ Hi-Hat clutch for the

RHH135 (1)

❑ Cable band for the

RHH135 (1)

❑ Stoppers for the

PCY135/155 (3)

❑ Felts for the

PCY135/155 (3)

❑ 2.5m stereo phone

cables (7)

❑ 4m stereo phone

cables (4)

❑ Cable bands (10)

❑ 2m spiral tube (1)

* You can cut this tube to any desired length and

use it in order to take up any slack of the cables.

❑ Owner’s Manuals

(for each Pad)

• PCY65/65S/135/155

• KP125W

• RHH135

❑ Tuning key (1)

Package 3 [Drum Trigger Module DTX900]

❑ Drum Trigger Module

DTX900 (1)

❑ Module stand fastening

screws (4)

❑ Module Stand (1)

❑ AC Power

Adaptor (1)

❑ DTX900 Owner’s Manual (1)

❑ DTX900 Data List (1)

Package 2 [DTP901]

❑ XP100T (Tom Pad) (3) ❑ Clamp bolt (3)

❑ CH755

(Cymbal Holder) (1)

❑ HS740A

(Hi-Hat Stand) (1)

❑ XP120SD (Snare Pad) (1)

❑ Additional holder clamp (1)

❑ XP100T/100SD/120T/120SD

Owner’s Manual (1)

❑ Assembly Manual (this sheet, 1)

1. Remove the right end support (shown below with a) of

the Rack, attach the additional Holder Clamp in the

direction shown below, then attach the support to the

Rack again.

2. Attach the Cymbal Holders (CH750 x 2 and CH755 x 1)

to the Rack System as shown below.

Attaching additional Holder

Clamps and Cymbal Holders

CH750

CH755

Additional

Holder Clamp

Loosen the

screws.

1. Attach the clamp bolt then tighten it with ﬁve or

six turns on each of three Tom Pads.

2. Attach three Tom Pads to the clamp rods on the

rack respectively. As shown below, attach the

Tom Pad to the rod part so that the rod part is to

be inserted to the hole of the Tom Pad, then

tighten the clamp bolt ﬁrmly.

3. If you want to change the location (height and

angle) of the Tom Pad, use the clamp bolts A

and B. Loosen the one of the clamp bolts,

adjust the location of the Pad, then make sure

to tighten the clamp bolts again before adjust-

ing another clamp bolt.

Attaching the Tom Pad

XP100T

Clamp bolt (to be

tightened as shown)

Tom pad (back side)

Clamp rod

Clamp bolt

To be

inserted

Rod parts

Tom pad

Clamp bolt A

Clamp bolt B

Continued on the next page (on the back side)

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

WT59070 910PO***.*01A0

Printed in Japan

1. Remove the wing nut and the two felt washers from

the Cymbal Holder. Then turn the tilter sleeve in a

counterclockwise direction and remove it.

2. Attach the stopper to the Cymbal Holder, and ﬁx at

a position where the L-shaped part of the stopper is

on the opposite side from you. To ﬁx the position of

the stopper, use the tuning key and tighten the key

bolt ﬁrmly.

3. Attach the tilter sleeve removed in step 1 to the

Cymbal Holder again, and tighten it in a clockwise

direction.

4. Attach one of the felt washers removed in step 1 to

the Cymbal Holder. The other felt washer will not be

used within the standard assembly described in this

manual.

5. Insert the end of the L-shaped part of the stopper

into the oval-shaped hole (shown as a) on the

Cymbal Pad to set the Pad on the Holder.

* Cymbal Pad PCY135 is very similar to Real High-

Hat Pad RHH135. Check the model name on the

reverse side.

6. Attach the included round-shaped felt with a large

hole-diameter to the Cymbal Holder, then attach

the wing nut removed in step 1 and tighten it. Turn

the wing nut until you are certain that the Cymbal

Pad is attached. The Cymbal Pad is designed to

shake when you hit the surface, even when the

wing nut is tightened securely.

Attaching the Cymbal Pad

PCY135

PCY155

Cymbal

holder

Wing nut

Felt washer

Tilter sleeve

Tuning key

Key bolt

Stopper

Felt washer

Tilter sleeve

Felt washer supplied

with the Cymbal Pad

Wing nut

1. Attach the included module stand to the back side

of the Drum Trigger Module by using the module

stand fastening screws.

2. Attach the module stand onto the holder clamp,

then tighten the knob to ﬁx the position.

Attaching the Drum Trigger Module

Drum Trigger

Module

Module stand

fastening screw

Drum Trigger Module

(back side)

Module stand

Front side of

the module

Drum Trigger Module

+ module stand

Holder Clamp

Knob

1. If a drum mat (sold separately) is not available, lay

a sheet of cardboard on the ﬂoor to prevent

scratching the surface.

2. Loosen the wing bolt (shown with a) of the Hi-Hat

Stand.

3. Spread out the legs of the tripod part until it stands

stable. Tighten the wing bolt loosened in step 2.

4. Insert the radius rod into the hole of the frame as

shown below.

5. As shown at right, loosen the wing bolt (shown with

b) to remove the hi-hat clutch.

* The hi-hat clutch is not used within the standard

assembly described in this manual. Use the hi-hat

clutch included in the RHH135.

6. Pull out the hi-hat shaft ı from the upper pipe Å.

7. Insert the hi-hat shaft ı removed in step 6 into the

nut of the lower pipe Ç.

8. Insert the upper pipe Å into the hi-hat shaft ı from

above, then tighten the wing bolt (shown with c at

right) at the position where the cymbal support

plate is positioned at the middle area of the hi-hat

shaft ı.

9. Remove the felt washer and the cymbal support

plate attached above the support plate, since they

are not used within the standard assembly

described in this manual.

10. Set the Real Hi-Hat Pad RHH135.

* Refer to “Setting Up” in the RHH135 Owner’s Man-

ual.

Assembling the Hi-Hat Stand

Radius rod

Wing bolt

Hi-Hat clutch

Cymbal

support

plate

Support

plate

Cymbal sup-

port plate

Felt washer

Locate the Hi-Hat Stand, Kick Pad and Snare Stand as desired, referring to “Unit Standard Assembly” on the front page.

Before assembling the unit, lay a drum mat (sold separately) on the ﬂoor. If a drum mat is not available, lay the cardboard of the included package

under the Hi-Hat Stand and Kick Pad to prevent damaging the ﬂoor.

Connecting the pads to the Drum Trigger Module

Connect the cables plugged into the Output jacks of the Pads to the Input jacks of the Drum Trigger module.

Connect the AC power adaptor to the Drum Trigger Module.

The assembly is now completed.

* For information about the next steps such as tuning the power on/off and checking the actual sound,

refer to “Setting Up” in the Owner’s Manual of the Drum Trigger Module.

1. If a drum mat (sold separately) is not available, lay a sheet of cardboard on the

ﬂoor to prevent scratching the surface.

2. Attach the foot pedal (sold separately) to the Kick Pad KP125W, then ﬁx the

position so that the beater will hit the center of the Pad.

* Refer to the Owner’s Manual of the KP125W.

Assembling the Kick Pad

Pad

KP125W

(Kick Pad)

Beater

Foot pedal

(sold separately)

1. Spread out the legs of the tripod part then locate the Snare Stand on the ﬂoor.

2. Spread out the basket part of the Snare Stand, set the Snare Pad XP120SD on

the basket part, then use the adjustment knob to ﬁx the Snare Pad.

Assembling the Snare Stand and Snare Pad

Basket

XP120SD

(Snare Pad)

Legs

Adjustment

knob

NOTICE

1. As shown at right, connect the Pads with the Trigger Input jacks (q

SNARE – !0 KICK/!1 and HI-HAT CONTROL jack) of the Drum Trigger

Module by using the stereo phone cables.

• Insert the straight plugs of the cable into the Trigger Input jacks of the

Drum Trigger Module, then insert the L-shaped plugs of the cables into

each corresponding Pad.

• The stereo phone cable for TOM4 will not be used within the standard

assembly describled in this manual.

Rear panel of the Drum Trigger Module

!0 !1 iyrw

ou t e

Jacks of the Pads

RHH135

KP125W

1. Make sure the F (Standby/On) switch is set to the Standby position (?), then

connect the AC power adaptor to the DC IN jack on the rear panel. Twist the cable

around the cable clip to prevent the DC plug from inadvertently being discon-

nected.

2. Use the cable bands to bind the cables to the rack as shown at right. If necessary,

use the spiral tube.

3. Connect the other end of the AC power adaptor to the AC outlet.

DC IN jack

Cable clip

F (Standby/On) switch

Rear panel of the Drum Trigger Module

Yamaha DTX-900K Инструкция по применению

Бренд: Yamaha

Модель: DTX-900K

Категория: Музыкальные барабаны

Тип: Инструкция по применению

Это руководство также подходит для

DTX900K

Улучшить свои навыки игры на барабанах благодаря функциям обучения, встроенному метроному и возможности записи собственной игры.
Играть в любимые песни, подключив устройство к музыкальному проигрывателю или компьютеру.
Создавать собственные музыкальные композиции с помощью встроенного секвенсора и звукового генератора.
Подключить дополнительные пэды и тарелки для расширения возможностей установки.

Скачать PDF

сообщить о нарушении

на других языках

English: Yamaha DTX-900K Owner's manual
français: Yamaha DTX-900K Le manuel du propriétaire
italiano: Yamaha DTX-900K Manuale del proprietario
español: Yamaha DTX-900K El manual del propietario
Deutsch: Yamaha DTX-900K Bedienungsanleitung
Nederlands: Yamaha DTX-900K de handleiding
português: Yamaha DTX-900K Manual do proprietário
dansk: Yamaha DTX-900K Brugervejledning
polski: Yamaha DTX-900K Instrukcja obsługi
čeština: Yamaha DTX-900K Návod k obsluze
svenska: Yamaha DTX-900K Bruksanvisning
日本語: Yamaha DTX-900K 取扱説明書
Türkçe: Yamaha DTX-900K El kitabı
suomi: Yamaha DTX-900K Omistajan opas
română: Yamaha DTX-900K Manualul proprietarului

Yamaha DTX-900K Инструкция по применению

Это руководство также подходит для

Yamaha DTX-900K Инструкция по применению

на других языках

Похожие модели бренда