Yamaha V3 Руководство пользователя

Бренд: Yamaha

Модель: V3

Категория: Музыкальные инструменты

Тип: Руководство пользователя

Это руководство также подходит для

DME Setup Manual 1

DME Setup Manual

This manual describes the process of setting up a DME system, from making the initial DME processor settings

(DME64N / DME24N / DME8i-C / DME8o-C / DME4io-C / DME8i-ES / DME8o-ES / DME4io-ES) to synchronizing with

the DME Designer application installed on a computer.

n For details about the DME units refer to the manual supplied with the speciﬁc device, and for details about the DME Designer

application refer to the pdf-format DME Designer manual.

n In this document the term “DME” will refer to the DME64N, DME24N, DME8i-C, DME8o-C, DME4io-C, DME8i-ES, DME8o-ES and

DME4io-ES, while the term “DME Satellite” will refer only to the DME8i-C, DME8o-C, DME4io-C, DME8i-ES, DME8o-ES and DME4io-ES.

Workﬂow

Software Installation

● DME Designer and DME-N Network Driver installation (page 3).

● USB-MIDI Driver installation (page 4).

DME Network Setup (page 6)

Connecting via a USB cable and setting the DME IP address and Device Group Master/Slave status from the

DME Designer.

Computer to DME Connection (page 8)

The procedures for connecting a single DME unit to a computer as well as for connecting multiple DME units to a

computer in the same subnet are described. Refer to the DME manual for information on audio connection and

further network connection details.

Computer Network Setup

These settings must be made properly when connecting a computer to DME units via an Ethernet cable.

● Computer TCP/IP settings (page 9).

● DME-N Network Driver settings (page 11).

DME Designer Operation

● Creating Conﬁgurations (page 12).

Explains the process of launching the DME Designer application and combining and connecting various

audio components to create conﬁgurations.

● Going Online (page 14)

Explains how to go online and transfer conﬁgurations created using the DME Designer application to DME

devices.

Troubleshooting (page 17)

Appendix

● DME64N/24N Network Setup via Panel Operation (page 19).

● DME-N Network Driver Setup Details (page 20).

DME Setup Manual 2

Begin by downloading the DME Designer Combo Installer and the USB-MIDI Driver from the “Downloads” page on

the Yamaha Pro Audio website.

http://www.yamahaproaudio.com/

System Requirements

Software Installation

Windows

XP Professional/XP Home Edition/2000 Professional

CPU

1 GHz or higher Intel

Core

™

/Pentium

/Celeron

family processor

Memory

256 MB or more

Hard disk space

300 MB or more

Display

1,280 x 1,024 pixels or higher; High Color 16-bit or higher

Other

Mouse, 100Base-TX/10Base-T Ethernet or USB connection

Windows

Vista Ultimate/Business/Enterprise

CPU

1.4 GHz or higher Intel

Core

™

/Pentium

/Celeron

family processor

Memory

1 GB or more

Hard disk space

300 MB or more

Display

1,280 x 1,024 pixels or higher; High Color 16-bit or higher

Other

Mouse, 100Base-TX/10Base-T Ethernet or USB connection

DME Setup Manual 3

●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●

DME Designer and DME-N Network Driver Installation

Install the DME Designer application and DME-N Network Driver from the DME Designer Combo Installer by

following the procedure outlined below.

n The following procedure is applicable even if an older version of the DME Designer and/or DME-N Network Driver is already installed.

n Be sure to read the license agreement at the end of this document before installing this software.

1 Open the downloaded and extracted “DME Designer Combo Installer V*.*.*” folder (*.*.* will be the version

number on the actual ﬁle), and double-click the “setup.exe” ﬁle located in the “Installer” folder.

The DME Designer Combo Installer setup dialog window will appear on the display.

2 Follow the on-screen instructions to install the software.

The DME Designer will be installed ﬁrst, followed by the DME-N Network Driver.

If a previous version of the DME Designer and/or DME Network Driver exists on the computer, the older software will be

uninstalled before installation of the new software begins. After the older software has been uninstalled, you will be asked to

restart the computer. In this case the computer must be restarted before the installation process can continue. The installer

will automatically be re-launched and the installation will continue after the computer has been restarted.

The software will be installed in a “DME Designer” folder in the “Program Files\YAMAHA\OPT Tools” folder (default).

n Refer to the pdf-format DME Designer manual for operating instructions. The manual is not installed by the installer. Download the

manual separately from the “Downloads” page on the Yamaha Pro Audio website.

http://www.yamahaproaudio.com/

n DME Designer V3 cannot communicate with DME devices using ﬁrmware version 2 or earlier. If you are using DME Designer V3, be

sure to update the DME device ﬁrmware to the latest version that can be downloaded from Yamaha Pro Audio website.

http://www.yamahaproaudio.com/

n The installer will launch automatically when the computer is restarted after the uninstall process, but in rare cases the installer may

be hidden by the task bar. In such cases click this icon to continue the installation.

DME Setup Manual 4

USB-MIDI Driver Installation

n You can also refer to the installation guide supplied with the driver for detailed installation procedures.

■ Windows Vista

1 Start the computer and log on with

administrator privileges while power to the DME

is off.

2 Connect the computer to the DME unit via a USB

cable.

3 Turn the DME power on: “Found New Hardware”

will be displayed.

4 Select [Locate and install driver software

(recommended)] ➞ [Don’t search online].

5 When a message appears prompting you to

insert the supplied disc, select [I don’t have the

disc. Show me other options.] ➞ [Browse my

computer for driver software (advanced).] ➞

[Browse], specify the downloaded and extracted

“Driver” folder, then click [OK].

6 Click [Next] to start installation.

7 When a message appears indicating that the

driver has been successfully installed, click

[Finish].

The driver has been installed.

■ Windows XP

1 Start the computer and log on with

administrator privileges while power to the DME

is off.

2 Select [Start] ➞ [Control Panel], and then

“Switch to Classic View” in the upper left of the

display to show all control panels and icons.

3 Select [System] ➞ [Hardware] ➞ [Driver Signing]

➞ [File Signature Veriﬁcation], and check the

radio button to the left of “Ignore—Install all

ﬁles, regardless of ﬁle signature” and click [OK].

Restore this setting to its original state after the

installation has been completed.

4 While the DME power is still off, connect the

computer to the DME unit via a USB cable.

5 Turn the DME power on, and the “Found New

Hardware Wizard” message will appear

automatically.

6 Select [Install from a list or speciﬁc location

(Advanced).] ➞ [Search for the best driver in

these locations], check only [Include this

location in the search], click [Browse] to specify

the downloaded and extracted “Driver” folder,

then click [OK].

7 Click [Next] to start the installation.

8 When a message appears indicating that the

driver has been successfully installed, click

[Finish].

9 Restart the computer when a message appears

prompting you to do so.

The driver has been installed.

DME Setup Manual 5

■ Windows 2000

1 Start the computer and log on with

administrator privileges while power to the DME

is off.

2 Select [My Computer] ➞ [Control Panel] ➞

[System] ➞ [Hardware] ➞ [Driver Signing] ➞

[File Signature Veriﬁcation] and check the radio

button to the left of “Ignore—Install all ﬁles,

regardless of ﬁle signature” and click [OK].

Restore this setting to its original state after the

installation has been completed.

3 While the DME power is still off, connect the

computer to the DME unit via a USB cable.

4 Turn the DME power on, and the “Found New

Hardware Wizard” message will appear

automatically.

Click [Next].

5 Select [Search for a suitable driver for my device

(recommended)] ➞ [Specify a location], click

[Browse] to specify the downloaed and

extracted “Driver” folder, then click [OK].

6 Click [Next] to start the installation.

7 When a message appears indicating that the

driver has been successfully installed, click

[Finish].

8 Restart the computer when a message appears

prompting you to do so.

The driver has been installed.

DME Setup Manual 6

After connecting the computer to the DME unit via a USB cable, the Device Group and IP address for each DME

unit can be individually set from the DME Designer.

n These parameters can also be set directly via the panel controls and displays of the DME64N and DME24N (page 19).

Device Group

When a system uses multiple DME units, the DME units can be controlled from the DME Designer application in

Device Groups. Since all devices in a group are controlled via the Device Group Master, one device in each group

must be assigned as the master device.

IP Address

All devices to be included in the same group must be assigned the same network address. The Device Group

Master is speciﬁed by its host address.

1 While the DME power is off, connect the computer to the DME unit via a USB cable.

2 Turn the DME power on.

3 Click [Start] ➞ [All Programs] ➞ [YAMAHA OPT Tools] ➞ [DME Designer] ➞ [DME Designer] to launch the

DME Designer application.

4 Click the MIDI Setup button to open the MIDI dialog box.

n If you can’t locate the MIDI Setup button on the display, it is most probably hiding in the taskbar. Double-click it to open the MIDI

dialog box.

5 Select the “YAMAHA USB IN 0-1” or “Yamaha DME NETWORK-1” input port in the [In] ﬁeld, and the

“YAMAHA USB OUT 0-1” or “Yamaha DME NETWORK-1” output port in the [Out] ﬁeld, and click [OK].

n If the DME port does not appear in the MIDI dialog box, check that the DME device’s power is turned on, and re-launch the DME

Designer application.

DME Network Setup

Network address Host address

USB cable

DME Setup Manual 7

From the DME Designer main panel, click [Port] in the [Setup] menu to open the Port dialog box.

7 Select “YAMAHA USB OUT 0-1” or “Yamaha DME NETWORK-1” in the [Tx] ﬁeld, and “YAMAHA USB IN 0-

1” or “Yamaha DME NETWORK-1” in the [Rx] ﬁeld, and click [OK].

8 In the main panel window click [Network Setup] in the [Hardware] menu to open the Network Setup dialog

box.

9 Make the following network settings, then click [OK].

1 MIDI Port List (Tx/Rx)

Select “YAMAHA USB OUT 0-1/YAMAHA USB IN 0-1” or “Yamaha DME NETWORK-1/Yamaha DME NETWORK-1” as the

DME port for the network settings.

2 Master/Slave

Selects Device Group Master or Slave status.

Master: One device must be assigned as the Master in each Device Group.

Slave: All other DME devices in the group should be set to Slave.

n When DME64N/24N and DME Satellite units are combined in a Device Group, be sure to assign a DME Satellite unit as the Group

Master.

3 IP Address

Set the IP addresses of the DME devices. All DME devices in the same Device Group must be set to the same network address.

n When only one DME device (Master) is used, set the IP address to “192.168.0.2”.

n The subnet mask is ﬁxed at “255.255.255.0”.

n The host address can be set from 2 to 253 for the Master device, and from 3 to 253 for Slaves.

n Always use a private address (192.168.0.2. through 192.168.255.253) unless it is absolutely necessary to use a global address.

Consult with the network administrator if it is necessary to use a global address.

Network address

Host address

DME Setup Manual 8

4 Master ID

When a device is assigned as a Slave in Master/Slave (2) above, this sets the host address for the Master device in that

group. This parameter cannot be set for the Master device.

5 Link Mode

Make sure that “100Base-TX” is selected.

10 If the system includes multiple DME devices, repeat the above settings for each individual device.

Refer to the DME manual for information on audio connection and further network connection details.

n If you will be using CobraNet™ for audio connections, the required bundle numbers and related settings must be made via the DME

Designer application.

n If you will be using EtherSound™ for audio connections, the routing and other EtherSound settings must be made via the AuviTran AVS-

ESMonitor software available from the AuviTran website:

http://www.auvitran.com/view.php?products_AVS-ESMonitor.php

Directly Connecting a Single DME Device to a Computer

When only one DME device is to be controlled, connect the device to the computer via a USB cable as described

in “DME Network Setup” on page 6.

Connecting Multiple DME Devices to a Computer in the Same Subnet

Connect multiple DME devices to the computer via a switching hub and Ethernet cables.

n It is possible to connect the computer to the Device Group Master using a USB cable.It is also possible to connect the computer to a

Slave DME using a USB cable if a DME Satellite is assigned as the Device Group Master.

n Use a switching hub that is capable of 100Base-TX operation.

n The maximum length of cables that can be used to connect DME units to a switching hub is 100 meters. Proper operation at this length,

however, will depend on the quality of the hub and cables used, and cannot be guaranteed.

n Use CAT5 STP (shielded twisted pair) type cable to maximize resistance to electromagnetic interference.

Computer to DME Connection

USB cable

Group Master

DME Satellite (IP Address: 192.168.0.2)

Device Group

Ethernet cable

Ethernet straight cable

DME Satellite

(IP Address: 192.168.0.3)

(Master ID: 2)

DME64N/24N

(IP Address: 192.168.0.250)

(Master ID: 2)

Computer

(IP Address: 192.168.0.100)

Switching hub

DME Setup Manual 9

These settings must be made when DME devices are connected via Ethernet cables.

Computer TCP/IP Settings

The computer’s IP address and TCP/IP ﬁltering must be set up to allow network communication with the DME

device(s).

■ Windows Vista

1 Select [Start] ➞ [Control Panel] ➞ [Network and

Sharing Center] ➞ [Manage network

connections] ➞ [Local Area Connection].

The “Local Area Connection Properties” dialog box will

be displayed.

2 Select [Internet Protocol Version 4 (TCP/Ipv4)]

on the [Networking] tab, then click [Properties].

The “Internet Protocol Version 4 (TCP/IPv4) Properties”

dialog box will be displayed.

3 Click [Use the following IP address] on the

[General] tab.

4 Enter your computer’s IP address into [IP

address], the Gateway’s IP address into [Default

gateway], and “255.255.255.0” into [Subnet

mask].

n When the computer and DME devices are connected in

the same subnet as described on page 8, the network

address must be set to that same address as the DME

devices, while the host address must be set to a

different value.

When the computer and DME devices are connected in

the same subnet, Set the gateway IP host address to 254.

5 Click [OK].

6 Restart your computer

■ Windows XP

1 Select [Start] ➞ [Control Panel].

The “Control Panel” is displayed.

2 If the “Control Panel” is in Category display,

click [Switch to Classic View].

3 Double-click [Network Connections] ➞ [Local

Area Connection].

The “Local Area Connection Status” dialog box will be

displayed.

4 Click [Properties] on the [General] tab.

The “Local Area Connection Properties” dialog box will

be displayed.

5 Select [Internet Protocol (TCP/IP)] on the

[General] tab, then click [Properties].

The “Internet Protocol (TCP/IP) Properties” dialog box will

be displayed.

6 Click [Advanced...], then [Properties] on the

[Options] tab.

The “TCP/IP Filtering” dialog will be displayed.

7 Select “Permit All” for TCP Ports, then click

[OK].

The display returns to the “Advanced TCP/IP Settings”

dialog. Click [OK] to return to the “Internet Protocol (TCP/

IP) Properties” dialog.

8 Click [Use the following IP address] on the

[General] tab.

Computer Network Setup

DME Setup Manual 10

9 Enter your computer’s IP address into [IP

address], the Gateway’s IP address into [Default

gateway], and “255.255.255.0” into [Subnet

mask].

n When the computer and DME devices are connected in

the same subnet as described on page 8, the network

address must be set to that same address as the DME

devices, while the host address must be set to a

different value.

When the computer and DME devices are connected in

the same subnet, Set the gateway IP host address to 254.

10 Click [OK].

11 Restart your computer.

■ Windows 2000

1 Select [Start] ➞ [Settings] ➞ [Control Panel] ➞

[Network and Dial-Up Connections] ➞ [Local

Area Connection].

The “Local Area Connection Status” dialog box will be

displayed.

2 Steps 4 and after are the same as for Windows

XP.

DME Setup Manual 11

DME-N Network Driver Settings

In order for the computer to recognize the DME device(s), it is necessary to register the IP address and device

name of the DME device that is the Device Group Master.

Connect the DME device(s) to the computer as

described on

page 8

, and turn the DME power on.

2 Double-click [Start] ➞ [Control Panel] ➞ [DME-N

Network Driver] to open the DME-N Network

Driver dialog box.

3 Click the [Advanced Settings] button to open the

“Advanced Settings” dialog box.

DME devices connected to the network can be

automatically detected via this dialog box.

4 Enter the IP address range over which you

would like to automatically detect connected

DME devices in the [Detect from] and [Detect to]

ﬁelds, and click [Start].

Automatic DME device detection will begin.

5 When automatic DME device detection has

ﬁnished, check the [Add] box of the DME device

that is to function as the Device Group Master,

and click [Add to Device List].

The “Advanced Settings” dialog box will close and return

to the “DME-N Network Driver” dialog box.

n If the IP address was not automatically detected,

6 Select the DME unit that is to function as the

Device Group Master from the Target Device

List, enter the Device Name and Device Port No.,

and click the [Apply] button.

Device Name

Displayed as the port name in DME Designer.

Device Port No. (MIDI port number)

Set to “1.” “2” is also available for DME64N/24N devices.

7 Click the [Save and Close] button to close the

dialog box.

DME Setup Manual 12

Creating Conﬁgurations

The process of launching the DME Designer application and combining and connecting various audio components

to create conﬁgurations is described below. The DME device(s) can be disconnected from the computer while

creating conﬁgurations.

1 Click [Start] ➞ [All Programs] ➞ [YAMAHA OPT Tools] ➞ [DME Designer] ➞ [DME Designer] to launch the

DME Designer application.

When the DME Designer is launched a new project will be created and a new zone (Zone 1) will appear in the designer

window.

If the designer window shown above does not appear, click the main panel window [Show/Hide] button to reveal it.

2 Place the appropriate DME objects in the designer window.

Select the required DME objects from the Toolkit window on the left of the display. Objects can be dragged and dropped into

the zone window, or double-clicked to place them in the current zone.

n Where required set the device group or sampling rate via the dialog box that appears when placing DME objects.

n If the sampling rate set here and the actual sampling rate set for the DME operation are different, excessive DSP may be required

and operation may not be possible. Be sure to match the sampling rates.

DME Designer Operation

Main Panel Window

Designer Window

Drag and Drop, or

Double-click

DME Setup Manual 13

3 As necessary double-click placed DME object to open the DME conﬁguration window.

Individual audio components can be placed and wired together as necessary to create “conﬁgurations” in the conﬁguration

window. For this example you can leave the conﬁguration empty. Refer to the DME Designer manual for detailed information

on creating conﬁgurations.

4 Select the [Scene Manager] item from the main panel window [Tools] menu to open the Scene Manager

dialog box.

The speciﬁed conﬁguration parameter settings can be saved as a “scene” via the Scene Manager dialog box.

5 Select the row containing the scene you want to save, and click the [Store] button.

6 Conﬁgurations and other settings can be saved as project ﬁles (“.daf” extension) by selecting the [Save

As] command from the main panel window [File] menu.

DME Setup Manual 14

Going Online

After connecting the computer to the DME devices and going online, you can transfer conﬁgurations created using

the DME Designer application to the DME devices. The DME devices and DME Designer are “online” when they

are connected and able to communicate with each other. DME devices can also be controlled in real-time when

online.

1 Connect the DME devices to the computer as described on page 8, and turn the DME power on.

2 Launch the DME Designer application, select the [Open] command from the main panel [File] menu, and

open the previously saved project ﬁle.

n The DME Designer can also be launched and the project ﬁle automatically loaded by simply double-clicking the project ﬁle icon.

3 Click the MIDI Setup button to open the MIDI dialog box.

n If the DME ports are not displayed, check that the DME power is on and re-launch the DME Designer application.

4 Select the input and output ports to be used to control the Device Group Master, then click [OK].

When connected via USB select “YAMAHA USB IN 0-1” or “Yamaha DME NETWORK-1”, and “YAMAHA USB OUT 0-1” or

“Yamaha DME NETWORK-1”, and when connected via Ethernet select the device name speciﬁed via the DME-N Network

Driver (page 11).

5 Select the [Port] item from the main panel window [Setup] menu to open the Port dialog box.

6 Select the output and input ports speciﬁed in step 4 in the [Tx] and [Rx] ﬁelds, and the appropriate

Device Group in the [Device Group] ﬁeld, then click [OK].

DME Setup Manual 15

7 Click the [Synchronization] item in the main panel window [Tools] menu to open the Synchronization

dialog box.

DME objects placed in the DME Designer application will be displayed in the [DME Designer] list on the left, and DME

devices connected to the network will be displayed in the [Network] list on the right.

n If multiple Device Groups have been set up, select the Device Group to be synchronized from the [Group] list.

8 Click the [DME Designer] list [IP Address] ﬁeld, and select the IP address corresponding to the DME

device.

9 Click the [Go On-line] button, and a dialog box conﬁrming the sync direction will appear.

DME Setup Manual 16

10 Select the [DME Designer -> Device] button, then click [OK] and the DME Designer conﬁguration will be

transferred to the DME device.

When synchronization has ﬁnished the [Go On-line] button will be grayed out and the main panel window [On-line] button

will light.

n When a conﬁguration has already been transferred to a DME unit, we recommend using the [DME Designer <- Device] button for

synchronization. The transfer time is faster than using the [DME Designer -> Device] button. However, if the conﬁguration has

been edited it is necessary to use the [DME Designer -> Device] button.

To go ofﬂine either click the main panel window [On-line] button or the [Go Off-line] button in the Synchronization dialog

box.

For more in-depth information on using the DME Designer application for system design, refer to the pdf-format

DME Designer manual. If you will be using CobraNet for audio connections, the required bundle numbers and

related settings must be made via the DME Designer application. If you will be using EtherSound for audio

connections, the routing and other EtherSound settings must be made via the AuviTran AVS-ESMonitor software.

DME Setup Manual 17

The USB-MIDI Driver cannot be installed.

• Is the USB cable connected correctly?

• Is the USB function enabled on your computer?

When you connect the DME to the computer for the ﬁrst

time, if the “Add New Hardware Wizard” does not appear,

the USB function on the computer may be disabled.

Perform the following steps.

1 Select [Start] → [Control Panel] (→ [System] →

[Hardware]) → [Device Manager].

The “Device Manager” window appears.

2 Make sure that no “!” or “x” marks appear at “Universal

serial bus controller” or “USB Root Hub.”

If you see the “!” or “x” mark, the USB controller is

disabled. Refer to the owner’s manual of your computer

for details.

• Is any unknown device registered?

If driver installation fails, the DME will be shown as an

“Unknown device,” and you will not be able to install the

driver. Delete the “Unknown device” by following the steps

below.

1 Select [Start] → [Control Panel] (→ [System] →

[Hardware]) → [Device Manager].

The “Device Manager” window appears.

2 Look for “Other devices.”

3 If you ﬁnd “Other devices,” double-click it to extend the

tree to look for “Unknown device.” If one appears,

select it and click the [Remove] button.

4 Remove the USB cable from the DME, and make the

connection again.

5 Install the driver again according to the instructions

described on page 4.

When controlling the DME from your

computer via USB, the DME does not

operate correctly.

• Did you install the USB-MIDI driver?

• Is the USB cable connected correctly?

•Have you selected an appropriate port in the DME

Designer?

Make sure that the settings in the DME Designer have the

combination of “YAMAHA USB IN 0-1” (Yamaha DME

NETWORK-1) and “YAMAHA USB OUT 0-1” (Yamaha DME

NETWORK-1). The combination of “YAMAHA USB IN 0-2”

and “YAMAHA USB OUT 0-2” can also be used for the

DME64N/24N. Settings combining different port numbers

(i.e., “YAMAHA USB IN 0-1” and “YAMAHA USB OUT 0-2,”

or “YAMAHA USB IN 0-2” and “YAMAHA USB OUT 0-1”)

cannot be used.

• Is the USB-MIDI Driver Thru ON/OFF parameter set

to “OFF”?

Go to [Start] → [Control Panel] → [Yamaha USB-MIDI

Driver] and make sure that the [Thru ON/OFF] parameter is

set to “OFF”.

•Have you selected the same USB ports in both the

DME Designer and another MIDI application?

Change the port setting so that the DME Designer and the

other MIDI applications use different ports.

• Does the number of registered MIDI devices exceed

the Windows limit?

The Windows operating system allows a maximum of 10

MIDI device drivers to be installed and registered. In some

cases changing the USB port to which a device is

connected can cause it to be recognized as a different

device, thereby “artiﬁcially” exceeding the limit. If MIDI

doesn't function properly try uninstalling and then re-

installing the USB-MIDI Driver.

• Are you using the latest USB-MIDI Driver supporting

DME?

The latest driver supporting DME can be downloaded from

the Yamaha website.

http://www

.yamahaproaudio.com/

• Did you launch DME Designer after connecting a

USB cable and turning the device ON?

Be sure to connect the USB cable and turn the device on

before launching DME Designer.

•Was the USB cable disconnected during operation?

If the USB cable is accidentally disconnected, DME

designer will not recognize the device even if the cable is

reconnected. You will have to restart DME Designer.

Troubleshooting

DME Setup Manual 18

When controlling the DME from your

computer via Ethernet, the DME does not

operate correctly.

• Is the Ethernet cable connected correctly?

• Is the DME-N Network Driver set up appropriately?

Did you enter an appropriate IP address?

• Is the computer network setup appropriate?

Select [Start] → [Control Panel] → [Network Connections]

→ [Local Area Connection], and conﬁrm the network

setup.

• Are the settings of DME and peripheral network

devices (including switching hubs) appropriate?

Refer to the relevant owner’s manuals for the DME and

peripheral network devices (including switching hubs) for

details.

•Have you selected an appropriate network port in the

DME Designer?

• Are you using the latest DME-N Network Driver

supporting DME?

The latest driver supporting DME can be downloaded from

the Yamaha website.

http://www

.yamahaproaudio.com/

• Do you have security software running on your

system?

Try to disable the security software once. Set it to allow use

of TCP port 12300 on the network card being used by the

DME-N Network Driver.

Cannot suspend or resume the computer

correctly.

• Do not suspend the computer while the DME

Designer is running.

If you are using Windows 2000, you may not be able to

suspend/resume normally, depending on the particular

environment (USB Host Controller, etc.). (Even so, simply

disconnecting and connecting the USB cable will allow

you to use the DME functions again.)

To install one of either the DME Designer

software or DME-N Network Driver:

The software or driver can be individually installed by

double-clicking the “Setup.exe” ﬁle located in the

downloaded and extracted “Installer\DMEDesigner_”

or “Installer\Networkdrv_” folder.

To uninstall the DME Designer software:

The DME Designer software can be uninstalled either

via [Start] → [Control Panel] → [Add or Remove

Programs], or via [Start] → [Program Files] →

[YAMAHA OPT Tools] → [DME Designer] → [Uninstall].

To uninstall the DME-N Network Driver:

The DME-N Network Driver can be uninstalled via

[Start] → [Control Panel] → [Add or Remove

Programs].

To uninstall the USB-MIDI Driver:

The USB-MIDI Driver can be uninstalled by double-

clicking the “uninstall.exe” ﬁle located in the

downloaded and decompressed “Uninstall” folder.

DME Setup Manual 19

DME64N/24N Network Setup via Panel Operation

DME64N and DME24N device group and IP address settings can be made directly via the device’s panel.

1 Turn on the DME64N/24N power.

2 Press the [HOME] key to display the main

screen.

3 Press and hold the [UTILITY] key for more than 2

seconds to display the Utility screen.

4 Press the [UTILITY] a few times until the Net

page appears.

5 Use the [▲] and [▼] keys to move the cursor to

the parameters listed below and press the

[ENTER] key.

The corresponding editing dialog will appear. Make the

settings indicated for each parameter below, and press

the [ENTER] key each time to conﬁrm and enter the

settings.

1 Master/Slave

Selects Device Group Master or Slave status.

Master: One device must be assigned as the Master in

each Device Group.

Slave: All other DME devices in the group should be set

to Slave.

n When DME64N/24N and DME Satellite units are

combined in a Device Group, be sure to assign a DME

Satellite unit as the group Master.

2 IP Address

Set the IP addresses of the DME devices. All DME

devices in the same Device Group must be set to the

same network address.

n When only one DME device (Master) is used, set the IP

address to “192.168.0.2”.

n The subnet mask is ﬁxed at “255.255.255.0”.

n The host address can be set from 2 to 253 for the Master

device, and from 3 to 253 for Slaves.

n Always use a private address (192.168.0.2. through

192.168.255.253) unless it is absolutely necessary to

use a global address. Consult with the network

administrator if it is necessary t use a global address.

3 Master ID

When a device is assigned as a Slave in Master/Slave

(1) above, this sets the host address for the Master

device in that group. This parameter cannot be set for the

Master device.

4 Link Mode

Make sure that “100Base-TX” is selected.

Appendix

Network address Host address

DME Setup Manual 20

DME-N Network Driver Setup Details

“DME-N Network Driver” Window

Select [Start] → [Control Panel] → [DME-N Network

Driver] to open the “DME-N Network Driver” window.

The parameters in this window set up the device

information to communicate with the DME-N Network

Driver.

1 Target Device List

The name, IP address, MAC address, and MIDI port

number of all devices registered to communicate with

the DME-N Network Driver are shown in this list. Click

the title bars to sort accordingly.

When a device is selected in the list, information

related to that device will be viewed and edited in the

Device information (2) area below the list.

Device Name

Device IP Address

Device MAC Address

Device Port No.

The name, IP address, MAC address, and MIDI port

number of the corresponding device. Refer to the Device

information (2) area for details.

[New] Button

Click this button to add a new device to the list. Edit the

device’s parameters as required via the ﬁelds in the

Device information (2) area below the list, the click the

[APPLY] button to add the speciﬁed device.

[Duplicate] Button

This button adds a device to the list by copying the data

from the currently selected device. Edit the new device’s

parameters as required via the ﬁelds in the Device

information (2) area below the list, then click the [APPLY]

button to add the speciﬁed device.

[Remove] Button

Deletes the selected device from the list. If the removed

device is not the lowest device in the list, all devices

below the removed device will be shifted upward to

maintain the continuity of the list.

[Remove ALL] Button

Deletes all devices from the list.

[Undo] Button

This button provides a one-step undo function that allows

you to undo a single operation and revert to the previous

state. The [Undo] button will be grayed out and

inaccessible immediately after an undo operation or after

the control panel is launched.

2 Device information

When a device that is registered for communication

with the DME-N Network Driver is selected in the

Target Device List, the communication parameters for

that device can be viewed and edited in the device

information ﬁelds.

[Device Name]

This is the name of the device selected in the Target

Device List. The initial default settings are “UNIT1”

through “UNIT256”, but the name can be edited as

required in this ﬁeld.

[Device IP Address]

The IP address of the device selected in the Target

Device List can be set via these ﬁelds. Refer to page 7

for details on checking and setting its IP address.

n The IP address must be set properly or communication

with the device will not be possible.

[Device MAC Address]

The MAC (Media Access Control) address of the device

selected in the Target Device List can be set via these

ﬁelds. The MAC address of each device is permanently

assigned when the device is manufactured and cannot

be changed. The MAC address parameter is included to

prevent data from being sent to the wrong device if the IP

address in inadvertently set incorrectly. Refer to page 7

for details on checking its MAC address.

n The MAC address must be set properly or

communication with the device will not be possible.

n The MAC address of the connected device cannot be

changed.

[Device Port No.]

The MIDI port number of the device selected in the

Target Device List can be set via this menu. The MIDI

port number also functions as device ID number. It can

be set to “1” or “2” for DME64N/24N units. It should be

set to “1” for DME Satellite units.

n The MIDI port number must be set properly or

communication with the device will not be possible.

[Apply] Button

Click the [Apply] button after editing the Device Name,

Device IP Address, Device MAC Address, or Device Port

No. parameters to actually apply the changes. Also,

Страница загружается ...

Yamaha V3 Руководство пользователя

Бренд: Yamaha

Модель: V3

Категория: Музыкальные инструменты

Тип: Руководство пользователя

Это руководство также подходит для

Скачать PDF

сообщить о нарушении

Yamaha V3 Руководство пользователя

Это руководство также подходит для

Yamaha V3 Руководство пользователя

на других языках

Похожие модели бренда