Terra tdx420C Инструкция по применению

Бренд: Terra

Модель: tdx420C

Тип: Инструкция по применению

Это руководство также подходит для

Twin DVB-S/S2/S2X & DVB-T/T2/C to DVB-T/ISDB-T transmodulators

tdx420C, ttx420C, tdx420, ttx420

EN RU

Vers. 1.18

This product complies with the relevant clauses of the European Directive 2002/96/EC. The unit must be recycled

or discarded according to applicable local and national regulations.

Equipment intended for indoor usage only.

This product is in accordance to following norms of EU: EMC norm EN50083-2, safety norm EN IEC62368-1, RoHS norm EN50581.

This product is in accordance with Custom Union Technical Regulations: “Electromagnetic compatibility of technical

equipment“ CU TR 020/2011, “On safety of low-voltage equipment“ CU TR 004/2011.

This product is in accordance with safety standard AS/NZS 60065 and EMC standards of Australia.

Manual in .pdf

Product description

The devices are transmodulators with two DVB-S/S2/S2X (tdx420C, tdx420), DVB-T/T2/C (ttx420C, ttx420) input channels

and two DVB-T/ISDB-T output channels. The devices are designed for digital transmodulation with Transport Stream

Processing of TV or Radio programmes issued from FTA (Free to air) or encrypted digital reception; in case of encrypted

signal, the CAM (Conditional access module) containing the operator's smart card must tted in the slot. Modules processor

enables, services ltering, modifying SI (Service Information), generating NIT (Network Information table), LCN (Local Channel

Number), restamping PCR (Program Clock Reference). All of the congurations can be changed by using the Web Interface.

tdx420C – transmodulator with two DVB-S/S2/S2X input channels and two DVB-T/SDB-T output channels with two CAMs.

ttx420C – transmodulator with two DVB-T/T2/C input channels and two DVB-T/SDB-T output channels with two CAMs.

tdx420 – transmodulator with two DVB-S/S2/S2X input channels and two DVB-T/SDB-T output channels.

ttx420 – transmodulator with two DVB-T/T2/C input channels and two DVB-T/SDB-T output channels.

Transmodulators can be used as stand alone devices.

The products are intended for indoor usage only.

Safety instructions

Installation of the transmodulator must be done according IEC60728-11 and national safety standards.

Any repairs must be made by skilled personnel.

Avoid placing the transmodulator next to heat sources such as central heating components or in areas of high humidity.

Keep the transmodulator away from naked ames.

If the transmodulator has been kept in cold conditions for a long time, bringing it into a warm environment may cause

condensation, so allow it to warm up for no less than 2 hours before powering.

Ventilation should not be impeded by covering the transmodulator, such as newspapers, table-cloths, curtains etc.

Mount the transmodulator in a vertical position only. If installing in a 19” rack system additional forced air cooling fans

may be required.

Always allow 10 cm of free space from the top, front and bottom of the unit to enable any heat to be dissipated.

3. External view

tdx420

tdx420C

Figure 1. External view of the transmodulators

1 - CA modules slots. Double PCMCIA sockets

(tdx420C, ttx420C).

1.1 - rst module CAM 1

1.2 - second module CAM 2

2 - ◄ - RF input of SAT IF signal, DC output for LNB

(tdx420C, tdx420);

RF input of terrestrial, cable signal, DC output for

preamplier (ttx420C, ttx420). F socket.

3 - ►- RF output (input signal loop-through). F socket.

4 - ETHERNET - control Ethernet interface. RJ45 socket.

5 - ACTIVITY (yellow) indicator of the control Ethernet

interface.

6 - LINK (green) indicator of the control Ethernet interface.

7 - RESET and default IP button.

Press button for more than three seconds to set default

IP address of the control Ethernet interface. Ethernet led

indicators "activity" [5] and "link" [6] will start to toggle

to inform, that the reset IP address request has been

accepted. Device will be restarted with default IP address.

To restore all parameters to default values (including

password), keep pressing the button for additional 4

seconds. The green (link) indicator will start blinking after

that time indicating, that a “restore defaults” command has

been accepted. Now the button can be released. Yellow

(activity) indicator will light on while resetting parameters.

After that device will restart with all default values.

8 - Power distribution bus connector.

9 - +12 V DC powering input. Screw terminal.

10 - RF input (output signal loop-through). F socket.

11 - RF output. F socket.

1.1 CAM 1 1.2 CAM 2

tdx420C

RESET

ETHERNET

DC OUT 13/18V

1 A max

DC IN 12V

TERRA

DC IN 12V

tdx420C

DC OUT 13/18V

1 A max

DC IN 12V

tdx420

RESET

ETHERNET

TERRA

tdx420

DC IN 12V

DC OUT 13/18V

1 A max

DC OUT 13/18V

1 A max

4. Installation instructions

Read the safety instruction rst.

All settings can be changed using the web browser via control Ethernet interface.

Disconnect power supply unit from the mains before making any changes in the connections of the module. Fasten the

module on DIN RAIL or individual holder.

Connect all necessary RF, powering and control cables. Shielded Ethernet cable is recommended.

Connect the 75 W load to the unused RF output F sockets.

Insert CA modules.

Connect power supply in to the mains.

Within 5-40 seconds of powering the module will run in normal operation mode.

Comments of the front panel indicators:

if the link with the control Ethernet interface is established - the LINK [6] indicator glows;

the ACTIVITY [5] indicator blinks, if communication via the control Ethernet interface is active.

5. MOUNTING

The module or mounting bracket must be xed with steel screws Ø 3.5-4 mm. The screws are not included in a package.

Mounting bracket on DIN rail should be connected to main potential equalization bus.

Mounting on a wall by screws Mounting on a bracket (ordering number 01960)

Perpendicular to the wall Parallel to the wall

Figure 2. Mounting of the transmodulator

Package contents

1. Transmodulator ............................................................. 1 pcs.

2. Spacer .......................................................................... 1 pcs.

3. 75 W terminator ............................................................. 1 pcs.

4. Bridge F quick to F quick .............................................. 1 pcs.

5. User manual ................................................................ 1 pcs.

Requirements for external power supply unit

• Output voltage +12 V ± 0.5 V

• Ripple at single and/or double mains frequency < 10 mV p-p

• Ripple & noise < 100 mV p-p

• Short circuit protection

• Double insulated (marked )

• Meet EN 55022 class B conducted emisions requirements, measuring with grounded load

1. 2.

Mounting on DIN rail

Figure 5. Mounting or removing to/from

DIN rail of plastic spacers (supplied).

Figure 3. Mounting to DIN rail

Figure 4. Mounting from DIN rail

DC IN 12V

TERRA

RESET

ETHERNET

tdx420

DC IN 12V

TERRA

RESET

ETHERNET

tdx420

DC IN 12V

TERRA

RESET

ETHERNET

tdx420

6. Operating

6.1 Initial conguration

All modules leave the factory with this control over Ethernet interface IP address: 192.168.1.10. In order to avoid conicts

with other IP addresses, it is necessary to perform an initial conguration in the local mode. Subsequently, it will be possible

to access the module via local area network (LAN), either to change the conguration or to check the operating status.

The modules leave the factory with the following control over Ethernet interface TCP/IP conguration:

IP address of the module: 192.168.1.10

Subnet mask: 255.255.255.0

Default Gateway: 192.168.1.1

To access each module, use a personal computer (PC) equipped with an Ethernet card and

RJ-45 cable (CAT-5E or CAT-6). The IP address of the PC/MAC must be congured within

the following range: 192.168.1.2 - 192.168.1.254 (do not use 192.168.1.10, since this is the

IP address of the module to be congured). To start the conguration of the module, open

your web browser and type in the following direction: http://192.168.1.10. The login prompt

will appear on the screen (see Figure 6).

Figure 6. Login window

Access to the module is protected by user name and password. The default user name and password is admin. Enter

the user name and password and click on "Login" button.

NOTE*: the default password - admin - can (and must) be changed as explained in the section 6.11.5 "User management".

During initial conguration you need to change the default control interface TCP/IP conguration as explained in the section

6.8 "IP settings".

NOTE**: If you are using Internet Explorer Web browser, supported versions are version 10 or higher.

Control interface IP address reset to default procedure: press the "RESET" [7] button for more than 3 seconds and release

it. After this operation the control interface IP address will be set to 192.168.1.10, for more information see section 6.8.

6.2 General conguration

Initial Web interface screen

The rst screen that appears when the module accessed is the "Main" window, which gives general information on the

device.

Figure 7. General information screen

In the top of each conguration screen you will see a main menu tabs [1]. Using it, you can switch between the dierent

conguration menu. The tab highlighted in yellow shows which menu is active at a given moment. The "System menu" tab

contains several submenu items. Also common elements for all screens are module title [2] and login information strings

[3]. The module title can be changed after pressing the "Change" button in the "Device information" table. Pressing on the

"Logout" string you can logout from module control.

[1]

[2]

[3]

Device information table

This shows the following data of module:

“Device model”: model of the module.

“Serial number”: serial number of the module.

“Software version”: module software version number.

“System time”: current time, synchronized from the TDT table of the input stream or NTP server. Local time oset can be

selected in the "IP settings" tab, see section 6.8 "IP settings".

“Up time”: time passed from last power-up or restart of the module.

Output bitrates table

It displays the output bitrate status of each channel in real time, Horizontal bar shows the percentage of used available

bandwidth in the channel. The 1st number right to the bar shows actual bitrate in Mbps. Next number shows maximum allowed

bitrate in the channel and it depends on modulation parameters. Ensure that actual bitrate would not reach more than 95%

of available bandwidth. Otherwise bitrate overow may occur.

System status table

It represents the following parameters at real time: Processor load in percents, internal temperature in degrees of Celsius,

power voltage in Volts.

Other device in the network

If there are any modules in the network their status and diagnostic information will be displayed as it is in Figure 7 "General

information screen". If modules status is red press the down arrow and diagnostic errors will be displayed. Make sure, that

Ethernet router is congured properly to pass SSDP packets (239.255.255.250:1900 and 239.255.255.246:7900). Also make

sure that all modules are connected to the same Ethernet network

Diagnostic information table

It displays all module errors and comments how to eliminate them.

Figure 8. Diagnostic information table with errors

6.3 RF inputs

Figure 9. "Input 1" table (DVB-S/S2/S2X input only) Figure 10. "Input 1" table "Source types = dSCR"

The Figure 9 "Input 1" table in modules with DVB-S/S2/S2X input consists of the following parameters:

"LNB LO frequency" - the LNB local oscillator lower frequency in megahertz. Use 9750 MHz for the universal converter.

"LNB HI frequency" - the LNB local oscillator upper frequency in megahertz. Use 10600 MHz for the universal converter.

“LNB Power” - power supply of the converter – can be set to “0”, “13V”, “18V”, “13V/22kHz”, “18V/22kHz”.

"Polarization" - the polarization of converter. Can be "Horizontal" or "Vertical".

“Source type” - the LNB types, there are several: Universal, Quadro, DiSEqC, dSCR EN50607, SCR EN50494 - see Figures

9, 10.

“Universal LNB” - power supply voltage of the converter is chosen according

to the selected polarization – 18 V Horizontal, 13 V Vertical; the 22 kHz is set

depending on given "LNB HI frequency" "LNB LO frequency" and “Input frequency”

parameters.

For example:

LNB Hi=10,600, LNB Lo=9750, then F=(950+10,600+2150+9750)/2=11,725 MHz.

“DiSEqC” - then DISEQC commands are used to select the satellite. Possible

commands: “Satellite A”, “Satellite B”, “Satellite C”, “Satellite D”, Vertical or

Horizontal polarization.

"dSCR" – first select source type as shown in Figure 10, then select

“dSCR/SCR mode“ Master or Slave (Master for module which has direct

connection to Unicable multiswitch or LNB and Slave for modules connected by

loop through). If Slave was selected, additionally type the IP address of Master

module. All the modules in the dSCR/SCR group must be in the same Ethernet

network. Next select "SAT input" and "User band", type in frequencies, symbol

rate press “Update” button and observe "dSCR" status.

"SCR" - same as "dSCR", just the user band frequencies must be typed in

manually as shown in Figure 11.

Figure 11. "Input 1" table "Source types = SCR"

Figure 12. Demodulator settings table (DVB-S/S2/S2X input only)

The Figure 12 "Demodulator settings table" in modules with DVB-S/S2/S2X input consists of the following parameters:

„SAT input“ - A parameter that can switch demodulator o or connect to any available RF input (Figure 13).

“User band” - parameter used in dSCR/SCR Switches.

„Input frequency“ - parameter is a frequency of transponder in MHz.

„Symbol rate“ - parameter is a symbol rate of transponder in kSym/s.

Figure 13. SAT input (DVB-S/S2/S2X input only)

For advanced "DVB-S2 options", press "Congure" link and "Advanced DVB-S2 parameters" will be displayed, see Figure 14.

“PLS" - Physical Layer Scrambling used in DVB-S2 as a way to improve data integrity. A number called the "scrambling

sequence index" is used by the modulator as a master key to generate the uplink signal. This same number must be known

by the receiver so that demodulation would be possible.

PLS mode - “Root“ or “Gold“.

Stream - parameter needed for multistream transponders.

NOTE: If advanced parameters is not needed make sure to leave them as shown in Figure 14.

Figure 14. "Advanced DVB-S2 parameters" tables (T2-MI deencapsulation is supported only in M.1 version)

NOTE: De-encapsulation of up to 2x T2-MI streams, the total streams bitrate must not exceed 50 Mbit/s.

New Feature "Congure TERRA dSCR system"

Before starting conguration please make sure that all multiswitches are

connected to module via splitter that lets DC through in both directions!

Press “Congure Terra dSCR system” and wait while the device scans all available

multiswitches. After scan nishes serial numbers and conguration will be displayed

(Figure 16).

Select “Total bands” count and SAT position (Figure 17).

Press “Congure” if you are using wideband multiswitches you will be able to change

the heterodyne frequency (Figure 18).

NOTE: Be aware when changing user band count you are also changing the maximum

bandwidth of transponder that you will be receiving.

Figure 15. "Input 1" table "Source types = dSCR"

Figure 16. Table "Congure SAT position and total bands"

Figure 17. Table "Congure SAT position and total bands" Figure 18. Table "Congure heterodyne frequency"

The Figure 19 "Demodulator settings table" in modules with DVB-T/T2/C input consists of following parameters: "Modulation

standard" - used to select from the "DVB-T/T2" and "DVB-C" modulation standards. "Preamplier power" - used to switch

on/o the power for the RF preamplier. "Input bandwidth" - the bandwidth of DVB-T/T2 transponder. Can be selected from

values 8 MHz and 7 MHz. "Input frequency" – the frequency of the terrestrial or cable transponder in MHz. Frequency step

is 0.1 MHz. When the tuner is locked to the DVB-T2 transponder with multi PLP modulation, the additional parameter "PLP

number" is displayed in the "RF input" table. When the "Modulation standard" is set to DVB-C, the „Preamplier power"

parameter is disabled and power for the RF preamplier is switched o; the "Input bandwidth" parameter is disabled and the

"Symbol rate" parameter is enabled. Enter the value in kilo symbols per second.

Figure 19. Demodulator settings table (DVB-T/T2/C input only)

Press „Update“ button to set new parameters.

Input status table

The following information is displayed in the table “Input status”:

“RF level” - RF signal level at the module input. Level indication - approximate.

The values of the following parameters are displayed only if the module has synchronized

with the input signal.

“Modulation standard” - detected standard of the input signal. Possible values of the

standard: DVB-S, DVB-S2, DVB-S2X, DVB-T, DVB-T2, DVB-C

“Frequency” - intermediate frequency (for DVB-S/S2/S2X) or RF frequency (for

DVB-T/T2/C) at the module input.

“Modulation” - modulation scheme of the input signal. Possible values of the modulation

scheme: QPSK, 8PSK, 16APSK, 32APSK (for DVB-S/S2/S2X) QPSK, QAM16, QAM32,

QAM64, QAM128, QAM256 (for DVB-T/T2/C).

“Modulation mode” - OFDM modulation mode of the input signal (for DVB-T/T2/C)

Values: 8k or 2k.

“FEC” - forward error correction.

“Guard interval” - guard interval of OFDM signal (for DVB-T/T2/C).

“Symbol rate” - the symbol rate of the satellite transponder in kilo symbols per second

(tdx420C only).

“SNR” - RF signal/noise ratio at the input of module.

“VBER” - bit error rate after Viterbi corrector. To get the signal without any errors at the

output of the tuner, VBER shall not exceed 2Е-4.

“PER” - ratio of the MPEG2 transport error packets to the whole number of packets.

If the number of error packet is equal to zero, the opposite value to whole number of

packets is displayed. Packet counters are reset during RF input parameters update.

“Input bitrate” - bitrate of the input signal.

Figure 20. Status table (for DVB-S/S2/S2X)

6.4. Transport Streams

One channel at a time can be congured in this page. Select proper channel from the list at „Choose input channel“

combobox (see Figure 21 "Transport streams page").

Figure 21. Transport streams page

A list of services in the selected channel will appear. „List of services“ table shows a list of available services. Icon before

the service name indicates service type. Bitrate of each service is measured in real time. Services that currently are not

running will be displayed as grayed. They can be selected and will be outputted normally when the services starts to running.

„LCN“ eld is a Logical Channel Number. Every service can have a „channel number“ and TV will sort channels according to

it. Just ensure, that all services in all channels have dierent numbers. Value 0 means, that LCN for that service is not used

at all and TV will sort these channels according to it’s own rules. If channel numbers are added, but TV does not recognize

it, check the following:

- If TV supports LCN?

- If Network ID and Original Network ID values are valid for the country, which is selected on TV?

„Enable“ dropbox enables the service to the selected output.

“Descramble” checkbox enables or disables descrambling.

Press onto „+“ sign and service information will be extended (see Figure 22 "Service details").

Figure 22. Service details

“Service title“ and “Service provider“ can be edited (multilanguage character support). „Scrambled ag“ will be inserted

into SDT (Service Description Table). Unchecking this checkbox will not descramble the content. It only carries information

about the scrambling status of the service. “Descramble” checkbox enables or disables descrambling.

"Service type": this is an 8-bit eld specifying the type of the service. The assignment of service type value for a Service

is described in EN 300 468. It shall be coded according to Figure 23.

"Parental control": this selection enables ability to restrict certain content viewable by the user. For example, parental control

eld is set to "Less than 6 years", than all content with maturity rating above 6 years old will be ltered out.

Figure 23. Service type coding

Service type Description

0 reserved for future use

1 digital television service (see note 1)

2 digital radio sound service (see note 2)

3 Teletext service

4 NVOD reference service (see note 1)

5 NVOD time-shifted service (see note 1)

6 mosaic service

7 FM radio service

8 DVB SRM service [49]

9 reserved for future use

10 advanced codec digital radio sound service

11 H.264/AVC mosaic service

12 data broadcast service

13 reserved for Common Interface Usage (CENELEC EN 50221 [37])

14 RCS Map (see ETSI EN 301 790 [7])

15 RCS FLS (see ETSI EN 301 790 [7])

16 DVB MHP service

17 MPEG-2 HD digital television service

18 to 21 reserved for future use

22 H.264/AVC SD digital television service

23 H.264/AVC SD NVOD time-shifted service

24 H.264/AVC SD NVOD reference service

25 H.264/AVC HD digital television service

26 H.264/AVC HD NVOD time-shifted service

27 H.264/AVC HD NVOD reference service

28 H.264/AVC frame compatible plano-stereoscopic HD digital television service (see note 3)

29 H.264/AVC frame compatible plano-stereoscopic HD NVOD time-shifted service (see note 3)

30 H.264/AVC frame compatible plano-stereoscopic HD NVOD reference service (see note 3)

31 HEVC digital television service (see note 4)

32 to 127 reserved for future use

128 to 254 user dened

255 reserved for future use

NOTE 1: MPEG-2 SD material should use this type.

NOTE 2: MPEG-1 Layer 2 audio material should use this type.

NOTE 3: For information on the use of these values, see clause I.2.3 and ETSI TS 101 547-2 [54]

(3D Guidelines of Frame Compatible 3D-TV).

NOTE 4: For information on the use of these values, see clause I.2.5 and ETSI TS 101 547-4 [62].

Individual streams can be disabled as well. Also PID number can be remapped manually by selecting checkbox “Other

PID” (Keep in mind than PID must be unique) otherwise PID remapping is done automatically.

Press onto „Update“ button to save changes and execute.

NOTE: If transparent mode is selected, all services of transponder will be passed to the output, including original PAT, SDT,

PMT, EIT, CAT, NIT tables, all changes that were made to these tables will be disregarded. No more than 95% of output

bandwidth usage is recommended, otherwise overow might occur.

6.5. NIT

Several tables related to NIT generation exist in this section. Figure 24 "Global TS parameters" describes following TS

parameters:

Figure 24. Global TS parameters

“Network ID”: is unique number within the geographical region dened by the “country code”. For a cable network usually

this is a single country code plus 0x2000 (8192). If there are more connected modulators in the network, they must have the

same Network ID.

Proper value depending on your country and operator can be found here:

http://www.dvbservices.com/identiers/network_id?page=1

“Private data specier (hex)”: can be inserted in the NIT table for proper LCN description. This value is described in TS

101162 specication. NorDig standard requires 00 00 00 29 value, UK should use 00 00 23 3A value.

Other options can be found here:

http://www.dvbservices.com/identiers/private_data_spec_id?page=1

The parameter will not be inserted into NIT if value is set to zero.

„Network name“ is the name of the network.

The 2nd table in the page describes Transport stream ID and Original network ID of each channel (see Figure 25). Each

stream in a network must have unique ID, called „Transport stream ID“. An Original_Network_ID is dened as the “unique

identier of a network”. It can be linked to Network ID or used value from this location:

http://www.dvbservices.com/identiers/original_network_id?page=1

Figure 25. Transport stream and original network IDs

Figure 26. Description of other streams in the network

Every channel in the network must be described in NIT. Otherwise TV automatic channel tuning function will not nd all

channels. All modules in the network will be monitored via standard SSDP protocol. NIT tables will be regenerated if any

change is detected in other modulators with the same Network ID. Make sure, that Ethernet router is congured properly to

pass SSDP packets (239.255.255.250:1900 and 239.255.255.246:7900). Also make sure that all modules are connected to

the same Ethernet network.

NOTE: If in the RF network exists transponders that is generated by old TERRA transmodulators/modulators, the frequencies

and modulation parameters must be lled manually (Figure 26).

6.6. RF outputs

Two adjacent OFDM (DVB-T output) channels can be congured in this section. There is requirement for channels to be

adjacent and sorted by frequency, see the Figure 27 "RF output settings (DVB-T output)". Each channel can have its own

constellation QPSK/QAM16/ QAM64 (DVB-T output), Code Rate (FEC) - there are ve valid coding rates: 1/2, 2/3, 3/4, 5/6,

and 7/8. Guard interval of OFDM signal, available selections:1/32, 1/16, 1/8, 1/4. The bandwidth of DVB-T transponder can

be selected from values 8 MHz and 7 MHz. Cell-ID information is optional.

Figure 27. RF output settings (DVB-T output)

"Output frequency“ parameter can be entered manually or selected as a channel from combobox. Channels that can be

selected from the list depend on which region is selected, see the 6.11.10 "Regions". If you need any other frequency –

select “Manual” and type the needed frequency. Frequency step is 0.1 MHz. „Enable“ checkbox will enable channel to the

output. Global attenuator can be entered up to 15 dB. Also there is individual precise attenuator up to 2.5 dB in step of 0.5 dB.

Press „Update“ to change settings. In case, if any modulation parameter was changed, both channels will be restarted

with new settings. Exception is „Attenuator“, changes in this parameter will not restart the modulator.

6.7. SNMP settings

Figure 28 "SNMP settings" table is located in “IP parameters” tab.

The description of the SNMP conguration parameters:

"Read Community" - community name acts as a password that is shared by multiple SNMP agents and one or more SNMP

managers. "Read Community" password is used for read-only access to the modules parameters.

"Write Community" - is the password used for read-write access to the modules parameters.

"Enable TRAP" - SNMP traps are alerts generated by agents on a managed device. Check this box to enable TRAP

generation. The module generates traps when the diagnostic message occurs.

"TRAP Community" - is the password used for accessing of TRAPS.

"Host IP #1","Host IP #2""Host IP #3" - IP addresses of hosts with SNMP managers, where TRAPS will be send.

Figure 28. "SNMP settings" table

6.8 IP settings

All device IP settings can be congured here – IP address, subnet mask, gateway,

DNS (Domain Name System), see Figure 29. Starting with software version 1.41,

the “WEB port” number can be customized. Default is 80. You must restart the

device for the port change to take eect. All other IP parameters will be updated

immediately after pressing „Update“ button and redirected to new location.

NOTE: Press the RESET and default IP button [7] for more than three seconds

to set default IP address of the control Ethernet interface (see Figure 1). Ethernet

led indicators "activity" [5] and "link" [6] will start to toggle to inform, that the reset

IP address request has been accepted. Device will be restarted with default IP

address.

To restore all parameters to default values (including password), keep pressing the

button for additional 4 seconds. The green (link) indicator will start blinking after

that time indicating, that a “restore defaults” command has been accepted. Now

the button can be released. Yellow (activity) indicator will light on while resetting

parameters. After that device will restart with all default values.

6.9 E-mail-settings

The device can send e-mail reports if errors were detected. SMTP

protocol is used for that. Figure 30 “E-mail-settings table” shows

parameters related to this feature. “Enable e-mail error report”

checkbox enables error monitoring. All errors within “timeout” period

will be gathered, and send to the e-mail address, provided in “Receiver

e-mail address” input box. Comma separated e-mail addresses can be

used to send report to multiple addresses. The timer will be started as

soon, as the rst error is detected, and stopped when e-mail is sent.

The timer will be restarted again if a new error will appear.

“Sender e-mail address” can be used as authentication in the SMTP

server side.

SSL (SMTPS) protocol is not supported.

Figure 30. E-mail-settings table

6.10 CAM settings

Figure 31. Conguration of CA modules

Figure 29. IP settings table

Figure 32. CAM conguration

SAT

INPUT

Demodulator 1

Demodulator 2

converter

DVB-T

output

Modulator 1

Modulator 2

CAM position on output, individual CAM-s

CAM position on input, individual CAM-s

TS Multiplex &

processing

SAT

INPUT

Demodulator 1

Demodulator 2

converter

DVB-T

output

Modulator 1

Modulator 2

CAM 1

CAM 2

TS Multiplex &

processing

CAM 1

CAM 2

SAT

INPUT

Demodulator 1

Demodulator 2

converter

DVB-T

output

Modulator 1

Modulator 2

CAM position on output, CAM-s chained on Line 1

TS Multiplex &

processing

CAM 1

CAM 2

SAT

INPUT

Demodulator 1

Demodulator 2

converter

DVB-T

output

Modulator 1

Modulator 2

CAM position on output, CAM-s chained on Line 2

TS Multiplex &

processing CAM 1

CAM 2

SAT

INPUT

Demodulator 1

Demodulator 2

converter

DVB-T

output

Modulator 1

Modulator 2

CAM position on input, CAM-s chained on Line 1

TS Multiplex &

processing

CAM 1

CAM 2

CAM position on input, CAM-s chained on Line 2

CAM 1

CAM 2

SAT

INPUT

Demodulator 1

Demodulator 2

converter

DVB-T

output

Modulator 1

Modulator 2

TS Multiplex &

processing

Conguration settings and information about CA modules is split into dierent tabs. Most important table “Conguration of

CA modules” can be found in “CAM conf.” tab. In the "Conguration of CA modules" table CAM restart function in case of

descrambling error can be enabled. It is recommended to turn o this option if not activated conditional access card has been

inserted. “CAM settings” and “CAM position” parameters changes the ow of TS. Demod.1 and Demod.2 streams can be

descrambled separately by selecting “Invidual CAM-s” or “Сhained on the line 1” or 2 as shown in Figure 32. CAM position

can be changed from output to input.

For example: “CAM position” is set to “on input” and “CAM settings” is set to “Chained on line #1”. This means that Demod.1

input’s stream travels through CAM 1 followed by CAM 2, then goes to multiplexer and nally to Modulator, see Figure 32.

Figure 33. CA information and menu tables

6.11 System menu

This menu tab contains following submenu items: “Event logs”, “Export parameters”, “Import parameters”, “Firmware

upgrade”, “User management”, “Restore defaults“, “ Reset the device“, “Time, Date”, “Language”. Mouse over to show the

list of this submenu.

6.11.1 Event logs

Various important events, errors, warnings will be logged into the system, see Figure 34 "Event logs". Each record has

an event type, which can be used to lter particular messages. Just select checkboxes in the „Logs ltering“ table and press

„Apply“. Other messages will be hidden.

„Erase logs“ button will erase all logs from the system.

“Export logs” button forms the le (log.html) which will be downloaded to PC.

Each record has a log time when the event appeared. Refer to 6.11.8 "Date and time settings" for instructions how to

congure time settings.

Figure 34. Event logs

The content of the remaining tables depends on the inserted CA module (refer to Figure 33 "CA information and menu

tables"). General information about inserted CA module is displayed in the “CA module information” table. When there is no

CA module inserted, "Status" line indicates message: "No module inserted" and remaining lines are empty. Otherwise, the

"Status" contains message "Initialized" and remaining lines are lled with information read from the CA module. As in the

example Figure 33 "CA information and menu tables", "CA module menu" table shows the menu for a particular CAM. Click

on the corresponding button to access dierent menu options. Click on the "Back" button to return to previous menu, click

on the "Home" button to return to start menu.

6.11.2 Export parameters

All settings of transmodulator can be exported for backup or copying to another device. Press “Export parameters” and

“parameters.xml” le will be downloaded to PC. This le can be imported only to the same type of device.

6.11.3 Import parameters

Exported parameters can be imported back to the device. Press onto “Click to select le” button (see Figure 35 "Import

parameters") to select exported le.

Figure 35. Import parameters

Press “Upload” button to send the le to the device.It will take several seconds to update all parameters after le upload.

After that, device will function with new conguration. No restart is required.

6.11.4 Firmware upgrade

Device rmware can be upgraded via web browser. Press the “Click to select le” button and select rmware binary le. If

valid le was selected, a version number of new rmware will be displayed. Otherwise an error message will appear. Press

the “Upload” button to upload new rmware to the device. Upload progress bar will appear and may take several seconds

to upload, depending on the size of a le and a network connection speed. A message will be displayed asking to restart

the device when the le was sent to the device. New rmware will be programmed into the device only after restart. It may

take additional minute or more to ash new program. Device will start up with a new rmware and continue to operate with

previous parameters. Additional new rmware features (if any) may need to setup additionally to take eect.

Avoid power supply interruption when a programming process is going on.

Device has possibility to load software revision history and check availability for new software release. Click the “Check

online” link. If computer (not device!) has internet access, it will show a list of all software releases with links to binary les.

Binary le can be downloaded and saved to computer (see Figure 36 "Firmware upgrade"). After that, use the rmware

upgrade method as described above.

Figure 36. Firmware upgrade

6.11.5 User management

User may change a password here. Length of the password is up to 16 symbols. Type current password and double enter

new password to change it.

If logged in user has admin role, new users can be added (see Figure 37 "User management").

Figure 37. User management

Enter it’s username, password, select a role and press „Add“ button.

Only administrator (user with a role „admin“) may manage other users.

NOTE: By giving your personal password or user access account for another person, you take full responsibility for all

module settings modications made by that person or anyone else they may give the password to.

6.11.6. Restore defaults

All parameters will be restored back to factory defaults after conrmation. The exception – IP address and users – these

parameters will be unchanged. To restore IP address and system password to system defaults, see „RESET“ button at

section 3, pos.7.

Several seconds can take to restore all parameters, so be patient.

6.11.7. Restart the device

Device will be restarted after conrmation to do it. This is an alternative to pressing a „RESET“ button when the device

is operating.

6.11.8. Date, Time

System time can be congured manually or taken from NTP server (only if module can access NTP server). Also there is an

option to select the time source from TS as shown in the Figure 34.

Figure 38. "Date, Time" settings table

6.11.9. Language

Device control panel supports several preinstalled languages. A change of language requires system restart. Note, that

all previously logged records will remain in previous language.

Additional languages can be installed under request. Contact our distributors for such possibility.

6.11.10. Regions

Device supports several preinstalled regions. Region can be changed without restarting the device, just select needed

region by pressing “Change” button in “Device information” table. The RF channel list depends on which region is selected.

Additional regions can be installed under request. Contact our distributors for such possibility.

Draugystes str. 22, LT-51256 Kaunas, Lithuania, tel.: +370 37

31 34 44, fax: +370 37

31 35 55

E-mail: [email protected], http://www.terraelectronics.com

Type tdx420C / tdx420 ttx420C / ttx420

RF input frequency range 950-2150 MHz 47-862 MHz

LNB/preamplifier 0/13/18 V & 22 kHz, 1 A** max. 12 V 100 mA

powering/control DiSEqC 1.0, EN50607, EN50494

level / impedance 45-85 dBµV / 75 W 40-80 dBµV / 75 W

loop through gain -1 ± 1 dB 0 ± 1 dB

standard DVB-S DVB-S2* DVB-T DVB-T2 DVB-C

modulation QPSK QPSK, 8PSK QPSK, QAM16, QPSK, QAM16, QAM16, QAM32,

APSK 8/16/32 QAM64 QAM64, QAM256 QAM64, QAM128,

QAM256

channel bandwidth - - 7 MHz, 8 MHz 7 MHz, 8 MHz -

symbol rate 2 ÷ 45 Ms/s 2 ÷ 45 Ms/s - - 1 ÷ 7.2 Ms/s

code rate 1/2, 2/3, 3/4, QPSK 1/2, 3/5, 2/3, 1/2, 2/3, 3/4, 1/2, 3/5, 2/3, 3/4,

5/6, 7/8 3/4, 4/5, 5/6, 8/9, 9/10 5/6, 7/8 4/5, 5/6

8PSK 3/5, 2/3, 3/4,

5/6, 8/9, 9/10

roll off 35 % 20 %, 25 %, 35 % - - 15 %

RF output standard DVB-T / ISDB-T

modulation QPSK/QAM16/QAM64 (DVB-T), QPSK/DQPSK/QAM16/QAM64 (ISDB-T)

frequency range 100 - 858 MHz, by step 100 kHz

channel allocation adjacent

level / impedance 90 ± 2 dBµV / 75 W

spurious level < -60 dB

MER ≥ 38 dB (100-780 MHz); ≥ 35 dB (780-862 MHz)

channel bandwidth 7/8 MHz

guard interval 1/4, 1/8, 1/16, 1/32

code rate 1/2, 2/3, 3/4, 5/6, 7/8

transmission mode 2K

total output level 0 ÷ -15.0 dB by 1 dB step

adjustment range

loop through frequency 47-862 MHz / ≤ 2.5 dB

range/loss

Transport max. bit rate output 31670 kbps

stream max. PID filter count unlimited

parameters

Management port standard IEE802.3 10/100 Base T

Supply voltage 12 V ±1 V

Current consumption 550 mA 650 mA

without external load

Current consumption 3 A 0.8 A

with maximum external load

Current consumption with maximum 3.6 A - 1.1 A -

CAM-s and external load

Operating temperature range 0o ÷ +50o C

Dimensions/Weight (packed) 48.5x198x112 mm/0.9 kg

7. Technical specications

pr.

* supports physical layer scrambling (PLS) and multiple input streams (MIS)

** only in v.1 and v.2 versions

pr. software control

Сдвоенные DVB-S/S2/S2X & DVB-T/T2/C в DVB-T/ISDB-T трансмодуляторы

tdx420C, ttx420C, tdx420, ttx420 RU

Vers. 1.18

Данный продукт соответствует требованиям Европейской Директивы 2002/96/EC. Устройство должно

быть переработано или утилизировано в соответствии с местными и региональными правилами.

Оборудование предназначено работать в закрытых помещениях.

Данный продукт соответствует следующим нормам Европейского Союза: электромагнитной совместимости EN50083-2,

безопасности EN IEC62368-1 и RoHS EN50581.

Данный продукт соответствует требованиям технических регламентов Таможенного Союза: “Электромагнитная

совместимость технических средств“ ТР ТС 020/2011, “О безопасности низковольтного оборудования“ ТР ТС 004/2011.

Данный продукт соответствует нормам безопасности по стандарту AS/NZS 60065 и нормам электромагнитной совместимости по

стандартам Австралии.

руководство

пользователя в .pdf

Описание изделия

Устройства представляют собой трансмодуляторы с двумя входными каналами, обеспечивающие прием сигналов

в формате модуляции DVB-S/S2/S2X (модели tdx420C и tdx420) или DVB-T/T2/C (модели ttx420C и ttx420), и двумя

выходными каналами для передачи сигналов в формате модуляции DVB-T/ISDB-T. Устройства предназначены для

цифровой трансмодуляции с обработкой транспортного потока теле- и радиопрограмм, передаваемых методом (FTA)

открытого или кодированного цифрового вещания. В последнем случае необходимо использовать модуль условного

доступа с картой оператора связи. Процессор модулей обеспечивает фильтрацию программ, внесение изменений

в сведения о программах, генерирование NIT (таблиц сетевой информации) и LCN (номеров логических каналов),

перемаркирование временных отметок программ. Все параметры конфигурации могут быть изменены с помощью

Web интерфейса.

tdx420C – трансмодулятор с двумя входными каналами для приема сигналов в формате DVB-S/S2/S2X и двумя

выходными каналами для передачи сигналов в формате DVB-T/ISDB-T и двумя модулями условного доступа;

ttx420C – трансмодулятор с двумя входными каналами для приема сигналов в формате DVB-T/T2/C и двумя

выходными каналами для передачи сигналов в формате DVB-T/ISDB-T и двумя модулями условного доступа;

tdx420 – трансмодулятор с двумя входными каналами для приема сигналов в формате DVB-S/S2/S2X и двумя

выходными каналами для передачи сигналов в формате DVB-T/ISDB-T;

ttx420 – трансмодулятор с двумя входными каналами для приема сигналов в формате DVB-T/T2/C и двумя

выходными каналами для передачи сигналов в формате DVB-T/ISDB-T.

Трансмодуляторы могут использоваться как автономно действующие устройства.

Изделия предназначены для установки и использования внутри помещений.

Инструкция по электробезопасности

Инсталляция трансмодулятора должна быть проведена в соответствии с требованиями IEC60728-11 и национальных

стандартов безопасности.

Ремонтировать трансмодулятор может только квалифицированный персонал.

Не устанавливайте трансмодулятор вблизи приборов отопления, а также в помещениях повышенной влажности.

Держите трансмодулятор вдали от открытого огня.

После длительного хранения трансмодулятора при низкой температуре, необходимо перед включением выдержать

его в теплом помещении не менее двух часов.

Не закрывайте трансмодулятор посторонними предметами, напр. газетами, шторами;

При инсталляции крепите трансмодулятор в вертикальном положении. При инсталляции модуля в 19''

коммутационную стойку, может понадобится дополнительный вентиляторный блок для охлаждения модулей.

Сверху, cпереди и cнизу установленного трансмодулятора должно быть не менее 10 см свободного

пространства.

Страница загружается ...

Terra tdx420C Инструкция по применению

Бренд: Terra

Модель: tdx420C

Тип: Инструкция по применению

Это руководство также подходит для

Скачать PDF

сообщить о нарушении

на других языках

English: Terra tdx420C Owner's manual

Terra tdx420C Инструкция по применению

Это руководство также подходит для

Terra tdx420C Инструкция по применению

на других языках

Похожие модели бренда

Модели других брендов