Kuppersberg FQ 65 W Руководство пользователя

TECHNICAL PASSPORT

ПАСПОРТ ТЕХНИЧЕСКОГО ИЗДЕЛИЯ

GAS HOB

ГАЗОВЫЕ ВАРОЧНЫЕ ПОВЕРХНОСТИ

TG 699, TG 69, TS 69, TS 79, TG 79, TG 799, TS

63, TS 39, TG 39, TG 99, FQ4TG, FV3TG, FQ3TG,

FQ7TG, TG49, FQ6TG, FQ 65, TS 62, TS 99

2

TECHNICAL PASSPORT ENGLISH

Gas hob

1. APPEAL TO THE CUSTOMER .......................................................................................... 3

2. CHILDREN’S SAFETY ..........................................................................................................3

3. IMPORTANT SAFETY INSTRUCTION .........................................................................3

4. ENVIRONMENTAL PROTECTION ................................................................................. 5

5. BEFORE USING YOUR APPLIANCE FOR THE FIRST TIME ............................ 6

6. MAINTENANCE AND INSTALLATION MANUAL .................................................. 7

6.1. SAFETY INSTALLATION ......................................................................................... 7

6.2. INSTALLING THE APPLIANCE ............................................................................ 8

6.3. ELECTRICAL CONNECTION .................................................................................. 12

6.4. GAS CONNECTION ....................................................................................................12

6.5. ADJUSTMENT OF HOB PER GAS TYPES ........................................................ 13

6.6. STARTING THE APPLIANCE .................................................................................14

6.7. TECHNICAL CHARACTERISTIC AND DRAWINGS ...................................... 15

6.8. TECHNICAL INFORMATION ON GAS BURNERS .......................................16

7. CONTROL TYPES AND USE .............................................................................................17

7.1. CONTROL PANEL ........................................................................................................17

7.2. BASIC SETTINGS ........................................................................................................17

7.2.1. FOR GAS BURNERS ................................................................................................17

8. MAINTENANCE AND CLEANINGS ...............................................................................20

9. TROUBLESHOOTING ..........................................................................................................21

CONTENTS

3

ENGLISH TECHNICAL PASSPORT

Gas hob

1. APPEAL TO THE

CUSTOMER

Our Valued Customer,

Thank you for your purchase of our

product.

Please read all instructions and

warnings in this manual carefully.

This manual includes the important

information about safe installation,

usage and maintenance and the

required warnings for your utilization of

your equipment.

Please keep this manual at a safe

and easily accessible place to be used

as future reference.

The Producer may not be held liable

for the losses to human, environment or

other materials arisen from the faulty

use of the equipment.

2. CHILDREN’S SAFETY

Â The exposed parts of the product

shall be heated during and after the

use; the children should be kept away.

Â Do not place any object on the

unit that the children may reach.

Â Packaging materials may be

dangerous for children. Keep the

packaging materials in a place that

the children may not reach or classify

and recycle them as per the waste

instructions.

Â If constant supervision may not

be provided the children under age 8

shall be kept away of the unit.

Â This unit may be used by children

over 8 years old and the persons with

lack of physical, hearing or mental

abilities or lack of experience and

information, subject to guidance and

supervision or utilization of the unit

safely and recognition of the dangers.

Â Children should not play with the

unit.

Â Cleaning and maintenance of the

unit should not be conducted by the

children without supervision.

3. IMPORTANT SAFETY

INSTRUCTION

This device is produced for domestic

use. Our  rm is not liable for any losses

or damages which may occur due to

wrong or faulty installation.

Although this is a simple use product,

we recommend you to read this manual

carefully. In this sense, you may get

best performance from your device and

protect yourself and your surrounding

from the possible dangers.

Please consider the following

warnings in order to minimize the risks

which may be experienced by you in

utilization of the devices such as electric

shock, circumstances which may cause

losses/ damages to people.

Â Device is set to 220 -240 volt.

Â WARNING: The equipment and

its accessible parts are hot during use.

4

TECHNICAL PASSPORT ENGLISH

Gas hob

Â Best care should be used to avoid

contacting with the heating elements.

Â WARNING: Cooking with

vegetable oil or fat without required

care may be dangerous and may cause

 re.

Â Do not attempt to extinguish

any  re with water, the circuit of the

equipment is closed and then the  ame

is covered with a cover or  ame blanket.

Â WARNING: Fire Danger: Do not

store materials on cooking surface.

Â The accessible parts may be hot

during utilization.

Â Do not ever clean your hob by

using steam cleaners.

Â Do not use the unit in

circumstances affecting your judgment

such as being drank or drugged.

Â Since your device has grounding

plug your wall socket should also be

grounding type.

Â Use utmost care to prevent your

device’s electrical cable through hot

areas.

Â Use care that the gas hose will

be regulations in law institute stamped,

not be laid through hot areas, and it

should be checked with soap bubble

whether any gas leakage exists.

Â Use clamp to tighten the gas

hose after connecting it to the head of

the hose. Control whether there is any

gas leakage exists by using soap bubble.

Â Note that the LPG hoods should

have regulations in law institute stamp

and 300 mmSS (29,4 mbar) of outlet

pressure.

Â Natural gas pressure is 200

mmSS (19,6 mbar). Please consult the

authorized service for conversion to

natural gas or LPG.

Â Note: Usage of the gas baking

products shall cause heat and steam

formation at the places of existence. Be

sure that your kitchen is ventilated well.

Keep the natural ventilation outlets

open or install a mechanical ventilation

product (hood, aspirator).

NOTE:

Burners burning of setting can be

done between large and between.

GENERAL SAFETY WARNINGS

Â Since this unit was produced

for domestic use, it is not suitable for

commercial and industrial use. It is

dangerous and inappropriate to use it

for any other purpose (e.g. heating a

room).

Â Do not allow laying of the gas

hose and electric cord from the heated

part of the unit.

Â Keep any  aming, explosive and

ignition materials from your device.

Â Do not change the place of your

device when working and/ or it is hot.

Â When you do not use your hob,

close the feeding valve after making all

switches to “OFF” position.

5

ENGLISH TECHNICAL PASSPORT

Gas hob

Â Do not let your hob in operation

without supervision control it with

frequently.

Â Take out the plug from the wall

socket during handling, cleaning or

maintenance of the unit.

Â Do not ever attempt to remove

the cable from the wall socket by

handling the cable.

Â Do not use pans transferring the

excessive heat to the glass.

Â Place the pan right in the middle

of the burner.

Â Keep the pan on the hob carefully

and avoid dropping it.

Â The shapes in this guide are

schematic and may not be exact match

of your product. The values stated on

the marking on the unit or other printed

documents given with the unit are

the values obtained at the laboratory

pursuant to the applicable standards.

Such values may be changed as per the

usage and environment conditions of

the unit.

Â Do not heat the closed cans

and glass jars. The pressure which may

occur in such containers may cause

explosion.

Â Since the edges of the product

will be hot do not place explosive or

combustibles near the unit.

Â Do not place the empty pans and

containers on the operating hob eyes.

The glass surface may be damaged.

Â No plastic and aluminum

container is allowed over the unit since

it might be hot.

4. ENVIRONMENTAL

PROTECTION

This device is subject to 2002/96/

EC WEEE (Waste Electric and Electronic

Equipment) as per the applicable

directives of Europe. Before disposal

of the device, you need to prevent

negative results to human and

environment. Otherwise it would

be incompliant waste. This symbol

indicates that the unit should not be

disposed as domestic waste rather it

should be returned to some electronic

wastes collection center. The disposal

of the product should be conducted as

per the local environmental legislation.

You may obtain detail information on

disposal, reuse and recycling of the

product.

It is suitable with the applicable

regulations of WEEE.

6

TECHNICAL PASSPORT ENGLISH

Gas hob

This symbol indicates that the unit

should not be disposed as domestic

waste rather it should be returned

to some electronic wastes collection

center. The disposal of the product

should be conducted as per the local

environmental legislation. You may

obtain detail information on disposal,

reuse and recycling of the product.

Â Keep the original packaging of

the product.

Â Carry the product in its original

packaging, and abide the markings

thereon.

Â If the original packaging is not

available;

 Take care for the impacts

which may be applied on the outer

surfaces of the product.

 Place/ hold the product in

parallel to the ground during carrying

(as the upper side will be up).

 Carry the pan holders not

touching each other.

Packaging

All packaging materials are

recyclable. In order to contribute

environmental protection place the

packaging material wastes to the

recycling bins.

Disposal of the old equipments

The equipments being old and

useless should not be thrown to a waste

container directly. There may be some

parts allowing re-use. Also there may

be some environmentally dangerous

materials requiring to be given to a

collection center. Therefore you should

take your unit to a collection center that

you may learn from the manufacturer/

dealer in your city and insure that the

electronic parts will be recycled.

It is important to keep the user’s

manual for it will be important in the

event of change of the user of the

device.

Before disposal or scraping of the

device it is required to prevent harmful

and negative effects on human and

environment. Otherwise it would be

incompliant waste.

5. BEFORE USING YOUR

APPLIANCE FOR THE

FIRST TIME

Â Make sure that you remove all

packaging materials before using the

unit.

Â When you remove the hob from

the package make sure that hob and /

or the cable is full and undamaged, and

no impact was put at the bottom of the

device, otherwise consult your seller.

Â Any and all works on the gas

equipments and systems should be

conducted by the competent and

authorized persons.

7

ENGLISH TECHNICAL PASSPORT

Gas hob

Â Gas hobs cause heat and steam

formation at the environments in which

they are used.

Â Make sure that your kitchen

ventilated well. Keep the natural

ventilation channels open or use

ventilation product (hood).

Â Have the required maintenance

of the gas products by the competent

and authorized persons.

Â Clean the gas burners regularly.

Â Request the telephone numbers

from the local gas suppliers for

emergency cases.

Things to be done

when gas smells

Â Do not use  ame. Do not smoke

Do not operate the switch of any

electrical device. Do not use  xed or

mobile phone.

Â Close all valves on the gas

products and gas counters.

Â Open the doors and windows.

Â Go out of the house if you smell

gas still.

Â Warn the neighbors.

Â Cal the  re service. Use a phone

outside the home.

Â Do not enter the house until you

will be noti ed that it is safe.

6. MAINTENANCE AND

INSTALLATION MANUAL

6.1. SAFETY INSTALLATION

The installation should be

conducted by an authorized

service

dealer as per the installation

instructions. Our  rm may not be held

liable for any losses and damages to

human, animals or objects due to any

inappropriate use of the unit.

PRE-INSTALLATION WARNINGS

ATTENTION: Before the installation

check that the gas type and gas pressure

stated under the product  t those of

your home. Call the authorized service

dealer for possible gas type changes in

future.

Â When the unit was taken off its

packaging make sure that it is strong,

not bent and has no fault at all. In the

event of any doubt consult the dealer.

Â Cut off the electric connection of

the unit from the main switch during

installation.

Â In order that built in cook-

tops will operate smoothly the

measurements of the counter on which

it will be mounted and the materials

used for installation should be proper,

and the counter should be resistant

against heat.

Read the following instructions

to ﬁ x the hob on the counter:

In order to prevent insertion of the

foreign materials and liquids between

the hob and the counter attache the

adhesive band on the counter hole

without allowing any overlapping

before the installation.

Place the hob on the counter hole to

center the installation hole.

Secure the unit on the counter by

using the installation sheet and screws.

Please review the following  gures

carefully so that the hob will be

installed properly.

8

TECHNICAL PASSPORT ENGLISH

Gas hob

6.2. INSTALLING THE APPLIANCE

This equipment should be mounted at the well ventilated places and as per the regulations

in force. The installation personnel should consider the laws and norms applicable to the

release of burning gases and ventilation.

Â The materials used on the surface and the link partitions under the counter should be

resistant against minimum 100°C.

Â A safe distance should be left between the hob and the counter walls (Fig. 1).

Â The hole to be provided for the hob on the counter should be as per the gure. (Fig. 1)

Â The distance between the hob sole and the partition should be at least 25 mm. (Fig. 2)

TS 69

TS 63

TS 62FQ7TG

Figure 1.

9

ENGLISH TECHNICAL PASSPORT

Gas hob

TG 39

FQ3TG

TG 99

FV3TG TG 69

TG 79

TG 799

TG 699

10

TECHNICAL PASSPORT ENGLISH

Gas hob

Â The distance between the cook

top ad another device (e.g. kitchen

hood) shall not be less than 700 mm

(Figure 2).

Â If 60 cm Hobs will be place on

a built in oven without any cooling

system, it is recommended to leave

300 cm2 of ventilation hole in order

TS 39 FQ4TG S

TS 79 TG 49

FQ6TG FQ 65

TS 99

11

ENGLISH TECHNICAL PASSPORT

Gas hob

Release of Burnt Gases

Â The air required for burning is

taken to the environment of the hob

and the burnt gas are released to the

environment. Proper ventilation should

be maintained for safe operation of the

unit. The ventilation openings de ned

as per the volume of the environment

are provided at the bale (Table 1).

Â Burnt gases should be discharged

outside by the hood with  ume.

Â If no kitchen hood is used,

an electrical ventilator should be

used having guaranteed capacity to

discharge 3-5 times of the kitchen air

to be installed at the wall or window of

the building (Figure 3)

MIN. 700 mm

25 mm

Figure 2.

Figure 3.

Table 1

1. Cooktop

2. Aspirator

3. Electrical ventilator

4. Ventilation Opening

VOLUME OF THE

ROOM (m.)

VENTILATION

OPENING (cm.)

Less than 5 m

3

Minimum 100 cm

2

Between 5m

3

and 10 m

3

Minimum 50 cm

2

Larger than 10 m

3

Not required

Basement or Cellar Minimum 65 cm

2

Installation of the Hob on the

Counter

Â In order to prevent insertion

of the foreign materials and liquids

between the hob and the counter

attache the gasket on the counter

hole without allowing any overlapping

before the installation.

Â Place the hob on the counter

hole to center the installation hole.

Â Secure the unit on the counter by

using the installation sheet and screws.

(Figure 1 and 5)

to insure air circulation. If 75 or 90 cm

cook-top will be placed the oven has to

have cooling fan.

12

TECHNICAL PASSPORT ENGLISH

Gas hob

Counter

Gasket

Installation Clamp

Figure 4.

Installation Clamp

Figure 5.

6.3. ELECTRIC CONNECTION

Â Electric connection should

be conducted by a competent and

authorized person.

Â The electric cable of your hob

should not be laid at hot regions.

Â When the power cable is

damaged this cable should be changed

with a special cable to be supplied by a

special cable agency or the authorized

service dealer.

Â No reducer, adapter, and switch

should be used for electrical connection

since it will cause excessive heat and

re.

Â Plug the electric cable to a

grounded wall socket. The manufacturer

hereby declares that it will be released

all liability in the event of any failure in

this issue.

Â The supply data of the electric

network should be suitable with the

data on the type label of the unit.

6.4. GAS CONNECTION

These instructions are prepared for

specialist personnel having required

competence, the installation of the

equipment should be suitable as per

the applicable standards.

All gas related works should be

conducted when the electric connection

was cut.

The value plate on the hob indicates

the gas type intended to be used for use

with the hob. Connection to the main

gas course or gas type shall be realized

after controlling the adjustment as per

the gas type.

Use only piping, gaskets or stamp as

per the applicable national standards.

In some countries where conic

connections are obligatory, conic

connection is provided. In such a case

the conic connection part should be

connected to the unit.

If the unit will be connected to a

exible hose, the length of the hose

shall not exceed 120 cm.

Before starting works related to gas

installation, please cut the gas supply.

13

ENGLISH TECHNICAL PASSPORT

Gas hob

Make the connection so that

no pressure will be applied on the

connection records and piping. Make

sure that the pipe will not cause any

clogging or contact with the sharp

corners.

Note that the gas hose will not be

laid through hot areas.

NOTE: Replace the gas hose of your

hob at 4 to 5 years even if it will be

undamaged.

NOTE: Check whether any gas

leakage after the connection with soap

and water. Do not ever use ame.

Make sure that no additional weight

to be applied on the gas hose.

And apply the following order for

installation:

1. In the order; male adaptor

cylindrical, gasket, female gas adaptor,

conical-cylindrical or cylindrical

cylindrical components,

2. Tighten connection place with the

keys so that the pipes will be in proper

position,

3. Attach coupling to the main gas

source by using hard copper pipe or

exible steel pipe.

WARNING; Final Check whether

any leakage exists at the pipes with a

solution with a soap, and do not ever

use ame.

equipment should be suitable as per

the applicable standards.

Â All gas related works should be

conducted when the electric connection

was cut.

In order to convert the hob, remove

the burner plates and ame circles

thereon. Replace the injectors as per

the followings, and change them with

the injectors with suitable diameters

dened in the user’s manual. Conduct

the works with a plain tip screwdriver

at a position to see valve setting screw

by removing the switches of the hob

and rubber seals. In order to set the

low ame level, turn the gas setting

screw on the valve to have minimum

gas setting ow. Do this setting after

installing the burner component of the

burner, burning the burner and bringing

the switch setting to minimum.

Flow setting screw should be

tightened in LPG conversions as it

should be released for conversion from

LPG to natural gas.

6.5. ADJUSTMENT OF HOB

PER GAS TYPES

These instructions are prepared for

specialist personnel having required

competence, the installation of the

14

TECHNICAL PASSPORT ENGLISH

Gas hob

Figure 6.

RIGHT WRONG

Â In order that the hob will

operate properly the grills and burner

components should be properly

positioned.(Figure 6)

Â Make sure that the ame of your

burner is in blue color and work quietly.

If the burner will burn in yellow color

or work with voice make sure that all

burners t properly. If the ame color

does not change to blue color then

apply the authorized service.

After realization of the hob,

complete the conversion transaction

by connecting the rubber seals and

switched in the same order.

These instructions should be

used by an authorized service. The

products should be installed as per

the regulations in force and in proper

manner. Before conducting any

transaction the electrical connections

of the hob should be cut by no means.

The type label on the hob indicates

the gas type planned to be used with

the unit.

6.6. STARTING THE APPLIANCE

FIRING OF BURNER

If your hob does not have built in

lighter or during black out place the

naked ame over the burner and push

the switch to bring it to the desired

position with counter-clockwise

movement. Gas adjustment should

be between maximum and minimum

levels, it should not be realized between

maximum and off positions. To close the

burner turn the switch clockwise till to

reach “off” position.

MODELS EQUIPPED WITH

LIGHTER SWITCH (Automatic

ignition)

In order to burn one of the burners,

press the switch down and bring the

switch to maximum position. When it

burns, ame is adjusted to the desired

intensity with the switch.

15

ENGLISH TECHNICAL PASSPORT

Gas hob

6.7. TECHNICAL CHARACTERISTIC AND DRAWINGS

TS 63 TS 69

TG 69 TS 39 TG 39

1. Mini wok burner control knob

2. Semi rapid burner control knob

(1,75 kW)

3. Auxilary burner control knob

4. Right cast iron grid

5. Auxilary burner

6. Semi rapid burner (1,75 kW)

7. Electric connection cable

8. Left cast iron grid

9. Mini wok burner

10. Wok burner control knob

11. Wok burner

12. Rapid burner

13. Rapid burner control knob

14. Semi rapid burner (1,4 kW)

15. Semi rapid burner control knob

(1,4 kW)

16. Middle cast iron grid

TG 99

FQ4TG FV3TG FQ3TG

FQ6TG

TG 799 FQ7TG TG 49 TS 99

TS 62 FQ 65

16

TECHNICAL PASSPORT ENGLISH

Gas hob

MODELS

TG 799

TG 99

FQ7TG

TS 79

TG 79

TS 99

TG 699

TG 69

FQ 65

TS 69 TS 63

TS 39

TG 39

FV3TG

FQ3TG

FQ4TG

TG 49

FQ6TG

TS 62

Number of Burner 5 Gas Burners

4 Gas

Burners

4 Gas

Burners

4 Gas

Burners

2 Gas Burners

3 Gas

Burners

4 Gas

Burners

Auxilary Burner (1 kW) 1 Unit(s) 1 Unit(s) 1 Unit(s) 1 Unit(s) 1 Unit(s) 1 Unit(s) 1 Unit(s)

Semi-rapid Burner

(1,4 kW)

- - - 1 Unit(s) - - -

Semi-rapid Burner

(1,75 kW)

2 Unit(s) 2 Unit(s) 2 Unit(s) 1 Unit(s) - 1 Unit(s) 2 Unit(s)

Rapid Burner (3 kW) 1 Unit(s) - - 1 Unit(s) 1 Unit(s) 1 Unit(s) 1 Unit(s)

Wok Burner (3,8 kW) 1 Unit(s) - 1 Unit(s) - - - -

Wok Burner (2,5 kW) - 1 Unit(s) - - - -

Total Power 11,3 kW 7 kW 8,3 kW 7,15 kW 4 kW 5,75 kW 7,5 kW

Gas Consumption G20-

20mbar

1077 l/h 667 l/h 791 l/h 682 l/h 381 l/h 548 l/h 715 l/h

Gas Consumption G30-

30mbar

822 g/h 509 g/h 604 g/h 519 g/h 291 g/h 418 g/h 545 g/h

Gas Category II2H3+ II2H3+ II2H3+ II2H3+ II2H3+ II2H3+ II2H3+

Installation Class 3 3 3 3 3 3 3

Electric Supply

220-240 V

50-60 Hz

220-240 V

50-60 Hz

220-240 V

50-60 Hz

220-240 V

50-60 Hz

220-240 V

50-60 Hz

220-240 V

50-60 Hz

220-240 V,

50-60 Hz

Flame Failure Safety

Device

Yes Yes Yes Yes Yes Yes Optional

Supply Cable YES YES YES YES YES YES YES

Automatic Ignition YES YES YES YES YES YES YES

Product Measurement

TG 799

FQ7TG

750x520 mm

TS 799

750x510 mm

TG 99

860x520 mm

TS 99

860x510 mm

TG 69

FQ 65

590x520

mm

TS 69

580x510

mm

TS 63

580x510

mm

TS 39

FV3TG

305x510 mm

TG 39

FQ3TG

320x520 mm

FQ4TG

TG 49

450x520

mm

FQ6TG

TS 62

590x520

mm

6.8. TECHNICAL INFORMATION ON GAS BURNERS

A Burner (1kW) SR Burner

(1,4 kW)

SR Burner

(1,75 kW)

R Burner (3 kW) Wok Burner

(2,5 kW)

Wok Burner

(3,8 kW)

G 30-30 mbar

LPG

(0,50 mm)

G 30-30 mbar

LPG

(0,57 mm)

G 30-30 mbar

LPG

(0,65 mm)

G 30-30 mbar

LPG

(0,85 mm)

G 30-30 mbar

LPG

(0,82 mm)

G 30-30 mbar

LPG

(0,98 mm)

G20–20 mbar NG

(0,72 mm)

G20–20 mbar NG

(0,85 mm)

G20–20 mbar NG

(0,97 mm)

G20–20 mbar NG

(1,15 mm)

G20 –20 mbar

NG

(1,15 mm)

G20 – 20 mbar

NG

(1,35 mm)

Note: The burner positions on the burner table are indicated on the burner plate.

17

ENGLISH TECHNICAL PASSPORT

Gas hob

1. Nitril/Clingiric Gasket

2. Elbow

3. LPG Hose Entrance

Complete the installation by using

gasket in the middle for the LPG hose

entrance indicated on the above ﬁ gure

during the natural gas LPG conversion.

7. CONTROLLER TYPES

AND USE

7.1. CONTROL PANEL

1. Rear burner control switch

2. Front burner control switch

1. Left front burner control switch

2. Left rear burner control switch

3. Right burner control switch

1. Left front burner control switch

2. Left rear burner control switch

3. Right rear hot-plate control switch

4. Right front burner control switch

1. Left front burner control switch

2. Left rear burner control switch

3. Middle burner control switch

4. Right rear burner control switch

5. Right front burner control switch

1. Left burner control switch

2. Middle front burner control switch

3. Middle rear burner control switch

4. Right rear burner control switch

5. Right front burner control switch

7.2. BASIC SETTINGS

7.2.1. FOR GAS BURNERS

Operation of the burners and power levels

Turn the control switch left-wise

until reaching to maximum level. When

you press the control switch all burning

igniters will have  ame to burn. Release

the switch in few seconds after burning

of the burner, and bring the control switch

to the desired  ame position between the

maximum and minimum levels.

18

TECHNICAL PASSPORT ENGLISH

Gas hob

If the ame is gone when you release

the switch You should repeat the above

process. But this time press the switch

and hold for about 10 seconds.

WARNING: Do not use burning

system more than 15 seconds. If the

burner will not be burned within such

time or if the ame will be cut for any

reason whatsoever, repeat burning

process after waiting for 1 minute.

Closing the burners

Turn the control switch right-wise to

close the hob.

Flame Failure Device (FFD)

All burners on your hob are equipped

with Flame Failure Device system against

ame extinguishing risk (water ow, wind

etc.) When the ame was gone while the

burner switch is open such system will

prevent cutting of the gas supplied to the

burner. If the burning of the burner will

be cut due to safety, repeat the burning

operation by switching the burner switch

to off position.

Figure 8.

Using Right Burner

Â The pan diameter and the

burner power should match in order to

efciently use it. The diameters proper

for each burner are given in the table.

Â Select the proper pan diameter

and volume in order to dene the

proper burner.

Pan Diameter

Burners

The Smallest

Diameter (cm)

The Largest

Diameter (cm)

Auxilary Burner(A) 12 16

Semi Rapid Burner

(SR)

14 20

Rapid Burner (R) 18 24

Triple Burner 22 26

Usage of grills and

recommendations

The pan grills on the hob are

designed for safe use of the hob. Please

make sure that the grills are placed

properly and lastic legs t well.

Â Do not use pans with the

deformed soles which may cause

instability on the grills.

Â Use pans with proper diameters.

Do not use smaller pans in the diameter

of the burner. When small pans are used

it may cause overowing and reduced

the efciency of the hob.

Â Do not cook with pans without lid

or semi closed pans to avoid energy loss.

19

ENGLISH TECHNICAL PASSPORT

Gas hob

Â Do not place the containers

directly on the burner covers use grill

always.

Â Place the cooking pan on the

burner evenly. The containers placed

on the burner inappropriately may be

tipped. Do not place the large containers

at the side of the switch switches may

be damaged. Do not place the pans on

the grills hardly.

Â Pay attention that the burner

place will not have any impact. And do

no place heavy objects on the tray.

Â Do not heat the pans as empty.

The pan sole may be deformed. The

heat on the sole may damage the burner

table surface.

Â The cold liquids should not be

thrown on the glass surface or burners

when the surface is hot.

Â Do not place sharp objects on the

hob.

Â Do not use pans transferring the

excessive heat to the bottom surface

directly.

Â In the event of any re do not

attempt to extinguish the ames with

water. Close the electric circuit of the

hob and use a material to cut the ame

like ame blanket.

Â This device should not be

operated with a timer or a remote

control.

Â Use at sole pans on the hob. In

this manner, thermal energy shall be

used to the maximum.

Â It is recommended not to use

concave pans.

Â Use dry sole pans on the burner.

Do not place the cover of the pan and

especially the wet ones on the burner.

Â Use a wet cloth to wipe the hob.

However, if it becomes dirty, use water

with detergent to insure drying, apply

lubrication oil over it for formation of

thin oil substrate.

Â If the surface of the plates worn

a few drops of oil or maintenance

products available in the market may

be used.

Â It is recommended to set

maximum level at the beginning of

cooking process and to use intervals and

burning levels as per the characteristic

and quantity of the foods to be cooked.

Warning

Â Do not leave the equipment

unattended since the heat of burners is

very high, and make sure that it will not

be operated by children.

Â Pay attention for combustion risk

in the event of cooking with vegetable

oil and fats.

Â Do not approach the hob with

combustible and explosives.

20

TECHNICAL PASSPORT ENGLISH

Gas hob

8. MAINTENANCE AND

CLEANING

Please comply with the following

rules before cleaning and maintenance.

Â Close the unit for safety purposes.

If your device is set to natural gas setting

close the valve. For LPG hobs close hood.

Â Take out the plug of your unit

from wall socket.

Â If the hob is hot wait until it will

be cooled.

Â In order that you use the glass

hob and grills for longer periods you

need to clean them with appropriate

cleaning agents at certain intervals.

Â Cleaning on stainless surfaces

should be conducted in accordance

with the steel surfaces, and the surface

should be dried preferably with a soft

leather part.

Â In order to avoid any damage to

the burning system do not use burning

system when the burners are not

installed.

Â After the thermo-coupled

cleaning providing plug and safety

system, clean it to place burners in

suitable manner.

Â Wash the upper burning heads at

certain intervals with water and clean

and dry the gas channels with brush. Pay

attention to install the burning heads on

their places.

Â When you clean the burner do

not use acid, thinner, benzene or similar

chemical.

Â You need to clean your glass

hob and its grills with suitable cleaning

agents in order to use it for longer

period.

Â It should be cleaned with suitable

cleaners for stains and oil.

Â Harsh cleaning agents, stain

removers and detergents, wire wool and

sponge should not be used.

Â No cold liquid should be poured

on the glass surface or the burners when

they are hot. The glass may crack due to

thermal shock.

Clean the hob regularly after waiting

for cooling after each use in order to

keep your hob at the best manner.

Do not take out the control switches

in any manner during cleaning.

Enamel Parts

All enamel parts are used by using

water with soap and suitable detergents.

The hob should be dried thoroughly

after the process.

Pan Supports

Grills may be washed in the

dishwasher.

Burner

The burners consisting of two parts

may be leaned by using detergent.

The burners should be dried after

cleaning process and placed their places

delicately.

In the electronic ignition models, the

electrode should be left cleaned all the

time.

In the safety valve models, the valve

should be cleaned for failsafe operation.

After completion of the process,

the burners should be placed in their

placement to their places.

The burning system should not

be used when burners are not in their

places to avoid damage to electronic

ignition system.

Страница загружается ...

Kuppersberg FQ 65 W Руководство пользователя

Kuppersberg FQ 65 W Руководство пользователя

на других языках

Модели других брендов