SICK WLA26 Инструкция по эксплуатации

Тип
Инструкция по эксплуатации
O P E R A T I N G I N S T R U C T I O N S
WLA26
O P E R A T I N G I N S T R U C T I O N S
WLA26
de
en
es
fr
it
ja
pt
ru
zh
Described product
W26
WLA26
Manufacturer
SICK AG
Erwin-Sick-Str. 1
79183 Waldkirch
Germany
Legal information
This work is protected by copyright. Any rights derived from the copyright shall be
reserved for SICK AG. Reproduction of this document or parts of this document is
only permissible within the limits of the legal determination of Copyright Law. Any modi‐
fication, abridgment or translation of this document is prohibited without the express
written permission of SICK AG.
The trademarks stated in this document are the property of their respective owner.
© SICK AG. All rights reserved.
Original document
This document is an original document of SICK AG.
2006/42/EC
NO
SAFETY
2
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
Contents
1 Safety information............................................................................ 4
1.1 General safety notes................................................................................ 4
1.2 Notes on UL approval............................................................................... 4
2 Intended use...................................................................................... 4
3 Operating and status indicators...................................................... 4
4 Mounting............................................................................................. 5
5 Electrical installation........................................................................ 5
6 Additional functions.......................................................................... 7
7 Commissioning.................................................................................. 8
7.1 Alignment.................................................................................................. 8
7.2 Check the application conditions............................................................ 9
7.3 Sensing range setting............................................................................... 11
7.4 Time function setting................................................................................ 12
7.5 Setting light/dark switching..................................................................... 13
8 Process data structure..................................................................... 13
9 Troubleshooting................................................................................. 13
10 Disassembly and disposal............................................................... 14
11 Maintenance...................................................................................... 14
12 Technical data.................................................................................... 15
12.1 Dimensional drawings.............................................................................. 15
CONTENTS
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
3
1 Safety information
1.1 General safety notes
Read the operating instructions before commissioning.
Connection, mounting, and configuration may only be performed by trained
specialists.
2006/42/EC
NO
SAFETY
Not a safety component in accordance with the EU Machinery Directive.
Do not install the sensor at locations that are exposed to direct sunlight
or other weather influences, unless this is expressly permitted in the operating
instructions.
These operating instructions contain information required during the life cycle of
the sensor.
1.2 Notes on UL approval
The device shall be supplied from an isolating transformer having a secondary overcur‐
rent protective device that complies with UL 248 to be installed in the field rated either:
a) max 5 amps for voltages 0 ~ 20 V (0 ~ 28.3 V peak), or
b) 100 / Vp for voltages of 20 ~ 30 V (28.3 ~ 42.4 V peak).
Alternatively, they can be supplied from a Class 2 power supply.
UL Environmental Rating: Enclosure type 1
2 Intended use
The WLA26 is an opto-electronic photoelectric retro-reflective sensor (referred to as
“sensor” in the following) for the optical, non-contact detection of objects, animals, and
persons. A reflector is required for it to function. If the product is used for any other
purpose or modified in any way, any warranty claim against SICK AG shall become void.
3 Operating and status indicators
WLA26x-xxxxxx00 WLA26x-xxxxxx01 WLA26x-xxxxxx02
1
2
3
1
23
5
1
23
4
1 SAFETY INFORMATION
4
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
WLA26x-xxxxxx30 WLA26x-xxxxxx31 WLA26x-xxxxxx32
1
2
3
6
1
23
5
6
1
23
4
6
1
BluePilot blue: alignment aid
2
LED indicator yellow: status of received light beam
3
LED indicator green: supply voltage active
4
Press-turn element: time function adjustment
5
Teach pushbutton: adjustment of light/dark switching
6
Teach-Button: adjusting the sensitivity
4 Mounting
Mount the sensor and the reflector using suitable mounting brackets (see the SICK
range of accessories). Align the sensor and reflector with each other.
Note the sensor’s maximum permissible tightening torque of < 1,3 Nm.
5 Electrical installation
The sensors must be connected in a voltage-free state. The following information must
be observed, depending on the connection type:
Male connector connection: Note pin assignment
Cable: wire color
Only supply/switch on the voltage once all electrical connections have been estab‐
lished.
Explanations of the connection diagram (following tables):
Alarm = alarm output
Health = alarm output
MF (pin 2 configuration) = external input, teach-in, switching signal
Q
L1
/C = switching output, IO-Link communication
Test = test input
U
B
: 10 ... 30 V DC
Table 1: Connections
Wxx26x- x4 xH x5 xI
1 = BN
2 = WH
3 = BU
4 = BK
5= GY
1
2
4 3
0.14 mm
2
AWG26
1
2
4 3
5
0.14 mm
2
AWG26
MOUNTING 4
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
5
Wxx26x- x9 xB
1 = BN
2 = BU
3 = not connected
4 = BK
5= WH
6 = GY
7 = not connected
I
N
= 4 A
3
7
2
1
6
5
4
I
N
= 6 A
Table 2: DC
WLA26
x-
xxX6XxxxA00 xxX6Xx
xxA01-
A99
Push-
pull
xx161 xx162 xx163 xx165 xx168 xx16A xx16L xx16N xx16x
PNP xx861 xx862 xx863 xx865 xx868 xx86A xx86L xx86N xx86x
1 = BN + (L+)
2 = WH MF
3 = BU - (M)
4 = BK Q
L1
/C
Default:
MF
Q
Q
Alarm Alarm Test
L+
no func‐
tion
Test
L+
no func‐
tion
www.sic
k.com
80227
09
Default:
Q
L1
/C
Q
Q
Q
Q
Q Q
Q Q www.sic
k.com
80227
09
Table 3: DC
WLA26x- xxXXXxxxZZZ
Push-pull xx111 xx112 xx114 xx116 xx421 xx422 xx721 xx722
PNP xx811 xx812 xx814 xx816 xxB21 xxB22 - -
BN + (L+)
WH Q
Q
Health Health Q
Q
Q
Q
BU - (M)
BK
Q
Q
Q
Q
Q
Q
Q
Q
GR - - - - Test
L+
Test
L+
Test
M
Test
M
5 ELECTRICAL INSTALLATION
6
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
Table 4: Push-pull, PNP, NPN
Push-pull
PNP
NPN
+ (L+)
Q ≤ 100 mA
‒ (M)
Push-pull
PNP
NPN
+ (L+)
Q ≤ 100 mA
‒ (M)
Push-pull
PNP
NPN
+ (L+)
Q ≤ 100 mA
‒ (M)
Push-pull
PNP
NPN
+ (L+)
Q ≤ 100 mA
‒ (M)
6 Additional functions
Alarm
Alarm output: The sensor (WLA26) features a pre-failure notification output (“Alarm” in
the connection diagram [see table 2]), which issues a notification if the sensor is only
ready for operation to a limited extent. The LED flashes in this case. Possible causes:
sensor or reflector is contaminated, sensor is out of alignment. In the good state: LOW
(0), if excessively contaminated HIGH (1).
Health
Health output: The sensor (WLA26) features a pre-failure notification output (“Health”
in the connection diagram [see table 2]), which issues a notification if the sensor is
only ready for operation to a limited extent or the cable has been interrupted. Possible
causes: Sensor or reflector is contaminated, sensor is out of alignment, cable is dam‐
aged. In the good state: HIGH (1), if excessively contaminated or in the event of cable
interruption LOW (0). The yellow LED indicator flashes in this case.
ADDITIONAL FUNCTIONS 6
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
7
Table 5: Alarm
Alarm ( 100 mA) Health (100 mA)
+ (L+)
Alarm
‒ (M)
+ (L+)
Health
‒ (M)
+ (L+)
Alarm
‒ (M)
+ (L+)
Health
‒ (M)
Test input
Test input: The sensors WLA26 feature a test input (“TI” or “Test” on the connection
diagram [see table 2]), which can be used to switch the sender off and, therefore,
check that the sensor is functioning correctly: If female cable connectors with LED
indicators are used, you have to ensure that the TI is assigned accordingly.
It is important that there is no object between the sensor and reflector; activate the test
input (see the connection diagram [see table 2]).
The send LED is shut down or the detection of an object is simulated. Refer to table 6
to check the function. If the switching output fails to behave in accordance with the
graphic, check the application conditions, see "Troubleshooting", page 13.
Table 6: Test
Test M Test L+
+ (L+)
Test
– (M)
+ (L+)
Test
– (M)
+ (L+)
Test
– (M)
+ (L+)
Test
– (M)
7 Commissioning
7.1 Alignment
Align the sensor with a suitable reflector. Select the position so that the red emitted
light beam hits the center of the reflector. The sensor must have a clear view of the
reflector, with no object in the path of the beam [see figure 1]. You must ensure that the
optical openings of the sensor and reflector are completely clear.
6 ADDITIONAL FUNCTIONS
8
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
Table: Alignment
Figure 1: Alignment 1
Figure 2: Alignment 2
7.2 Check the application conditions
WLA26 are photoelectric retro-reflective sensors in which the autocollimation principle
has been combined with a multi-receiver element, thereby ensuring the greatest possi‐
ble resistance to depolarizing objects combined with a very high sensing range. This
means the WLA26 has a high operating reserve (insensitivity to dust) and does not
exhibit any switching errors with depolarizing objects.
Adjust the distance between the sensor and the reflector according to the correspond‐
ing diagram [see table 7] (x = sensing range, y = operating reserve).
NOTE TIP:
Should switching errors nevertheless arise due to extremely depolarizing objects, the
WLA26 can also be adapted to these extreme conditions and the switching errors
suppressed by means of a teach-in (via IO-Link or using the Teach-in button on the
housing).
Table 7: Application conditions
0
100
10
1
6
5
2
1
1,000
4
(13.12)
8
(26.25)
20
(65.62)
16
(52.49)
12
(39.37)
Function reserve
Distance in m (feet)
Sensing range
WLA26P-xxxxx1xx
4
3
Figure 3: Characteristic line 1: Standard
reflector
1
Reflector PL20A
2
Reflector PL22
Distance in m (feet)
Sensing range
Sensing range typ. max.
1
2
3
4
5
6
0 8
(26.25)
12
(39.37)
4
(13.12)
16
(52.49)
20
(65.62)
5.5 70
11.5 16
0
12 17
0
12 18
0
18
10
0
8 10
0
15
Figure 4: Bar graph 1: Standard reflector
1
Reflector PL20A
2
Reflector PL22
3
Reflector PL250
4
Reflector PL30A
5
Reflector PL40A
6
Reflector PL80A, C110A
COMMISSIONING 7
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
9
3
Reflector PL250
4
Reflector PL30A
5
Reflector PL40A
6
Reflector PL80A, C110A
0
100
10
1
3
2
1
1,000
4
(13.12)
Function reserve
Distance in m (feet)
8
(26.25)
16
(52.49)
12
(39.37)
Sensing range
WLA26P-xxxxx1xx
Figure 5: Characteristic line 2: Reflective tape
1
Reflective tape REF-DG
2
Reflective tape REF-IRF-56
3
Reflective tape REF-AC1000
Distance in m (feet)
Sensing range Sensing range typ. max.
1
2
3
0
0
1.5 3
0
2.5 5
0
8 12
0
8
(26.25)
12
(39.37)
2
(6.56)
6
(19.69)
10
(32.81)
4
(13.12)
14
(45.93)
Figure 6: Bar graph 2: Reflective tape
1
Reflective tape REF-DG (50 x 50 mm)
2
Reflective tape REF-IRF-56 (50 x
50 mm)
3
Reflective tape REF-AC1000 (50 x
50 mm)
0
100
10
1
4
3
1
2
1,000
Function reserve
4
(13.12)
8
(26.25)
20
(65.62)
16
(52.49)
12
(39.37)
Distance in m (feet)
Sensing range
WLA26P-xxxxx1xx
Figure 7: Characteristic line 3: Fine triple
reflectors
1
Reflector PL10FH-1
2
Reflector PL10F
3
Reflector PL20F
4
Reflector P250F
Sensing range
1
2
3
4
0
0
5.5 80
4.5 6.5
0
7 10
0
10 13
0
Distance in m (feet)
Sensing range typ. max.
8
(26.25)
12
(39.37)
2
(6.56)
6
(19.69)
10
(32.81)
4
(13.12)
14
(45.93)
Figure 8: Bar graph 3: Fine triple reflectors
1
Reflector PL10FH-1
2
Reflector PL10F
3
Reflector PL20F
4
Reflector P250F
7 COMMISSIONING
10
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
0
100
10
1
5
2
3
41
1,000
Function reserve
4
(13.12)
8
(26.25)
20
(65.62)
16
(52.49)
12
(39.37)
Distance in m (feet)
Sensing range
WLA26P-xxxxx1xx
Figure 9: Characteristic line 4: Chemi‐
cal-resistant reflector
1
Reflector PL10F CHEM
2
Reflector P250H
3
Reflector P250 CHEM
4
Reflector PL20 CHEM
5
Reflector PL40A Antifog
Distance in m (feet)
Sensing range
Sensing range typ. max.
1
2
3
4
5
0
0 8
(26.25)
12
(39.37)
2
(6.56)
6
(19.69)
10
(32.81)
4
(13.12)
14
(45.93)
2 30.2
7 100
6 8
0
3.5 5
0
11 14
0
Figure 10: Bar graph 4: Chemical-resistant
reflector
1
Reflector PL10F CHEM
2
Reflector P250H
3
Reflector P250 CHEM
4
Reflector PL20 CHEM
5
Reflector PL40A Antifog
7.3 Sensing range setting
WLA26x-xxxxxx3xAxx with teach-in button:
There must not be any objects located between the WLA26 and the reflector. The
sensitivity is reduced by pressing the teach-in button (approx. 1-3 sec.). This primarily
suppresses false switching to extremely depolarizing objects. The sensing range is also
reduced, and therefore the operating reserve as well. Lead an object into the path of
the beam. The yellow LED goes out, meaning the object is detected and the setting is
correct.
COMMISSIONING 7
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
11
1...3 sec.
1
2
Figure 11: WLA26x-xxxxxx3xAxx, adjusting the sensing range with teach-in button
7.4
Time function setting
1
0
T1
T2
M
T4
T3
t
t
t t t
t
t t t t
t t t
t
t
t t
Input signal
0
T1
T2
T3
T4
M = Manual (specific setting via IO-Link)
1 ms 30.000 ms
2
7 COMMISSIONING
12
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
7.5 Setting light/dark switching
1
L
D
M
L light switching
D Dark switching
M manual (specific setting via IO-Link)
8 Process data structure
WLA26x-xxxxxxxxAxx:
A00 A70 A71 A72 A73 A75
IO-Link V1.1
Process
data
2 bytes 4 bytes
Byte 0: bits 15... 8
Byte 1: bits 7... 0
Byte 0: bits 31...
24
Byte 1: bits 13...
16
Byte 2: bits 15...
8
Byte 3: bits 7... 0
Bit 0 / Data
type
Q
L1
/ Boolean
Bit 1 / Data
type
Q
L2
/ Boolean Qint.1 /
Boolean
Q
L2
/
Boolean
Qint.1 / Boolean
Bit... /
Descrip‐
tion / Data
type
2 ...15 /
[empty]
2 ...15 /
[time mea‐
surement
value] /
UInt 14
2 … 15 /
[counter
value] /
UInt 14
2 … 15 /
[length /
speed
measure‐
ment] /
SInt14
2 /
Qint.1 /
Boolean
2 … 7 / [empty]
Bit... /
Descrip‐
tion / Data
type
3 … 15 /
[time mea‐
surement
value] /
UInt13
8 … 31 / [carrier
load] / UInt 24
9 Troubleshooting
The Troubleshooting table indicates measures to be taken if the sensor stops working.
COMMISSIONING 7
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
13
LED indicator/fault pattern Cause Measures
Green LED flashes IO-Link communication None
Switching outputs do not
behave in accordance with
table 4
1. Change of the configuration
2. Short-circuit
1. Adjustment of the configura‐
tion
2. Check electrical connections
Not all blue LEDs light up. a) Insufficient alignment
b) Contamination of the opti‐
cal surfaces
c) Particles in the light beam
d) Distance between sensor
and reflector is too large
e) Reflector is not suitable
a) Check alignment
b) Cleaning of the optical sur‐
faces (sensor and reflector).
c) Avoid contamination in the
air as far as possible
d) Check sensing range
e) SICK reflector is recom‐
mended
Yellow LED flashes Distance between sensor
and reflector is too large /
light beam is not completely
aligned to the reflector /
reflector is not suitable / Front
screen and/or reflector is con‐
taminated.
Check sensing range / check
alignment / SICK reflector is
recommended / Cleaning of
the optical surfaces (sensor
and reflector).
10 Disassembly and disposal
The sensor must be disposed of according to the applicable country-specific regula‐
tions. Efforts should be made during the disposal process to recycle the constituent
materials (particularly precious metals).
NOTE
Disposal of batteries, electric and electronic devices
According to international directives, batteries, accumulators and electrical or
electronic devices must not be disposed of in general waste.
The owner is obliged by law to return this devices at the end of their life to the
respective public collection points.
WEEE: This symbol on the product, its package or in this document,
indicates that a product is subject to these regulations.
11 Maintenance
SICK sensors are maintenance-free.
We recommend doing the following regularly:
Clean the external lens surfaces
Check the screw connections and plug-in connections
No modifications may be made to devices.
Subject to change without notice. Specified product properties and technical data are
not written guarantees.
9 TROUBLESHOOTING
14
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
12 Technical data
WLA26P
Sensing range (with reflector PL80A) 0 m ... 12 m
Light spot diameter/distance Ø 80 mm / 5 m
Supply voltage U
B
DC 10 ... 30 V
Ripple 5 V
SS
Current consumption ≤ 30 mA
1)
< 50 mA
2)
Output current I
max.
≤ 100 mA
Max. response time ≤ 500 μs
3)
Switching frequency 1000 Hz
4)
Enclosure rating
5)
see table 1:
x4, xH, x5, xI: IP66, IP67, IP69
6)
x9, xB: IP65
Protection class III
Circuit protection A, B, C, D
7)
Ambient operating temperature –40 °C ... +60 °C
8)
1)
16 VDC to 30 VDC, without load
2)
10 VDC to 16 VDC, without load
3)
Signal transit time with resistive load in switching mode. Deviating values possible in COM2 mode.
4)
With a light/dark ratio of 1:1 in switching mode. Deviating values possible in IO-Link mode.
5)
Pursuant to EN 60529
6)
Replaces IP69 K pursuant to ISO 20653: 2013-03
7)
A = U
B
-connections reverse polarity protected
B = inputs and output reverse-polarity protected
C = Interference suppression
D = outputs overcurrent and short-circuit protected
8)
Do not bend cables below 0°C.
12.1 Dimensional drawings
3
2
2
1
7.1 (0.28)
8.1 (0.32)
10.8 (0.43)
25 (0.98)
38.8 (1.53)
6.4
(0.25)
12.9
(0.51)
48.1 (1.89)
40 (1.57)
44.2 (1.74)
10
(0.39)
Ø 5.2 (0.2)
24.6 (0.97)
82.2 (3.24)
70 (2.76)
Ø 5.2 (0.2)
7.3
(0.29)
8.1 (0.32)
76.5 (3.01)
82.5 (3.25)
55.6 (2.19)
53.3 (2.1)
4
Figure 12: Dimensional drawing 1, cable
1
Center of optical axis
2
Fixing hole Ø 5.2 mm
3
Connection
4
Display and setting elements
M12
1
3
2
2
7.1 (0.28)
8.1 (0.32)
10.8 (0.43)
25 (0.98)
39 (1.54)
6.3 (0.25)
48.1 (1.89)
40 (1.57)
44.2 (1.74)
19.7
(0.78)
Ø 5.2 (0.2)
24.6 (0.97)
82.2 (3.24)
70 (2.76)
Ø 5.2 (0.2)
17
(0.67)
7.9 (0.31)
76.5 (3.01)
82.5 (3.25)
55.6 (2.19)
53.3 (2.1)
63.9 (2.52)
4
Figure 13: Dimensional drawing 2, male
connector
TECHNICAL DATA 12
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
15
B E T R I E B S A N L E I T U N G
WLA26
de
en
es
fr
it
ja
pt
ru
zh
Beschriebenes Produkt
W26
WLA26
Hersteller
SICK AG
Erwin-Sick-Str. 1
79183 Waldkirch
Deutschland
Rechtliche Hinweise
Dieses Werk ist urheberrechtlich geschützt. Die dadurch begründeten Rechte bleiben
bei der Firma SICK AG. Die Vervielfältigung des Werks oder von Teilen dieses Werks
ist nur in den Grenzen der gesetzlichen Bestimmungen des Urheberrechtsgesetzes
zulässig. Jede Änderung, Kürzung oder Übersetzung des Werks ohne ausdrückliche
schriftliche Zustimmung der Firma SICK AG ist untersagt.
Die in diesem Dokument genannten Marken sind Eigentum ihrer jeweiligen Inhaber.
© SICK AG. Alle Rechte vorbehalten.
Originaldokument
Dieses Dokument ist ein Originaldokument der SICK AG.
2006/42/EC
NO
SAFETY
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
17
Inhalt
13 Zu Ihrer Sicherheit............................................................................. 19
13.1 Allgemeine Sicherheitshinweise.............................................................. 19
13.2 Hinweise zur UL Zulassung...................................................................... 19
14 Bestimmungsgemäße Verwendung............................................... 19
15 Bedien- und Anzeigeelemente........................................................ 19
16 Montage.............................................................................................. 20
17 Elektrische Installation..................................................................... 20
18 Zusatzfunktionen.............................................................................. 22
19 Inbetriebnahme................................................................................. 23
19.1 Ausrichtung............................................................................................... 23
19.2 Einsatzbedingungen prüfen..................................................................... 24
19.3 Einstellung Schaltabstand....................................................................... 26
19.4 Einstellung Zeitfunktionen....................................................................... 27
19.5 Einstellung Hell-/Dunkelschaltend.......................................................... 28
20 Prozessdatenstruktur........................................................................ 28
21 Störungsbehebung............................................................................ 28
22 Demontage und Entsorgung............................................................ 29
23 Wartung.............................................................................................. 29
24 Technische Daten.............................................................................. 30
24.1 Maßzeichnungen...................................................................................... 30
INHALT
18
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
13 Zu Ihrer Sicherheit
13.1 Allgemeine Sicherheitshinweise
Lesen Sie vor der Inbetriebnahme des Geräts die Betriebsanleitung.
Der Anschluss, die Montage und die Konfiguration des Geräts dürfen nur
von geschultem Fachpersonal vorgenommen werden.
2006/42/EC
NO
SAFETY
Bei diesem Gerät handelt es sich um kein sicherheitsgerichtetes Bauteil im
Sinne der EU-Maschinenrichtlinie.
Installieren Sie den Sensor nicht an Orten, die direkter Sonneneinstrahlung
oder sonstigen Wettereinflüssen ausgesetzt sind, ausser dies ist in der Betriebs‐
anleitung ausdrücklich erlaubt.
Die vorliegende Betriebsanleitung enthält Informationen, die während des Lebens‐
zyklus der Lichtschranke benötigt werden.
13.2 Hinweise zur UL Zulassung
The device shall be supplied from an isolating transformer having a secondary overcur‐
rent protective device that complies with UL 248 to be installed in the field rated either:
a) max 5 amps for voltages 0 ~ 20 V (0 ~ 28.3 V peak), or
b) 100 / Vp for voltages of 20 ~ 30 V (28.3 ~ 42.4 V peak).
Alternatively, they can be supplied from a Class 2 power supply.
UL Environmental Rating: Enclosure type 1
14 Bestimmungsgemäße Verwendung
Die WLA26 ist eine optoelektronische Reflexions-Lichtschranke (im Folgenden Sensor
genannt) und wird zum optischen, berührungslosen Erfassen von Sachen, Tieren und
Personen eingesetzt. Zur Funktion wird ein Reflektor benötigt. Bei jeder anderen
Verwendung und bei Veränderungen am Produkt verfällt jeglicher Gewährleistungsan‐
spruch gegenüber der SICK AG.
15 Bedien- und Anzeigeelemente
WLA26x-xxxxxx00 WLA26x-xxxxxx01 WLA26x-xxxxxx02
1
2
3
1
23
5
1
23
4
ZU IHRER SICHERHEIT 13
8020357.19RH / 15.01.2021 | SICK
Subject to change without notice
19
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139

SICK WLA26 Инструкция по эксплуатации

Тип
Инструкция по эксплуатации

Задайте вопрос, и я найду ответ в документе

Поиск информации в документе стал проще с помощью ИИ