Yamaha Audiogram3 Инструкция по применению

Бренд: Yamaha

Модель: Audiogram3

Категория: Аудио-микшеры

Тип: Инструкция по применению

Yamaha Audiogram3 — это USB-аудиоинтерфейс для передачи цифровых аудиоданных и программное обеспечение Cubase AI DAW (цифровая звуковая рабочая станция) для операционных систем компьютеров Windows® и Macintosh®. С помощью устройства AUDIOGRAM 3 и персонального компьютера вы получаете базовые элементы высокопроизводительной системы компьютерной записи, которую легко настроить и эксплуатировать.

AUDIOGRAM 3 Owner’s Manual

AUDIOGRAM 3

Owner’s Manual

C0 (10.11.30)

EnglishDeutschFrançaisEspañolRussian

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Manual de instrucciones

Руководство пользователя

USB AUDIO INTERFACE

Русский

EnglishDeutschFrançaisEspañol

AUDIOGRAM 3 Owner’s Manual

1. IMPORTANT NOTICE: DO NOT MOD-

IFY THIS UNIT!

This product, when installed as indicated in

the instructions contained in this manual,

meets FCC requirements. Modiﬁcations not

expressly approved by Yamaha may void your

authority, granted by the FCC, to use the

product.

2. IMPORTANT: When connecting this prod-

uct to accessories and/or another product use

only high quality shielded cables. Cable/s

supplied with this product MUST be used. Fol-

low all installation instructions. Failure to fol-

low instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and

found to comply with the requirements listed

in FCC Regulations, Part 15 for Class “B” digi-

tal devices. Compliance with these require-

ments provides a reasonable level of

assurance that your use of this product in a

residential environment will not result in harm-

ful interference with other electronic devices.

This equipment generates/uses radio fre-

quencies and, if not installed and used

according to the instructions found in the

users manual, may cause interference harm-

ful to the operation of other electronic devices.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

Compliance with FCC regulations does not

guarantee that interference will not occur in all

installations. If this product is found to be the

source of interference, which can be deter-

mined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using

one of the following measures:

Relocate either this product or the device that

is being affected by the interference.

Utilize power outlets that are on different

branch (circuit breaker or fuse) circuits or

install AC line ﬁlter/s.

In the case of radio or TV interference, relo-

cate/reorient the antenna. If the antenna lead-

in is 300 ohm ribbon lead, change the lead-in

to co-axial type cable.

If these corrective measures do not produce

satisfactory results, please contact the local

retailer authorized to distribute this type of

product. If you can not locate the appropriate

retailer, please contact Yamaha Corporation of

America, Electronic Service Division, 6600

Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those

products distributed by Yamaha Corporation

of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : COMPUTER RECORDING SYSTEM

Model Name : AUDIOGRAM 3

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undes-

ired operation.

See user manual instructions if interference to radio reception is suspected.

(FCC DoC)

(class b korea)

AUDIOGRAM 3 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from

electrical shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not

limited to, the following:

• Do not open the device or attempt to disassemble the internal

parts or modify them in any way. The device contains no

user-serviceable parts. If it should appear to be

malfunctioning, discontinue use immediately and have it

inspected by qualiﬁed Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp

or wet conditions, or place containers on it containing

liquids which might spill into any openings. If any liquid

such as water seeps into the device, unplug the USB cable

from this device immediately. Then have the device inspected

by qualiﬁed Yamaha service personnel.

• Never insert or remove a USB cable with wet hands.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others,

or damage to the device or other property. These precautions include, but are not limited to, the following:

• Before moving the device, remove all connected cables.

•Avoid setting all volume controls to their maximum.

Depending on the condition of the connected devices, doing

so may cause feedback and may damage the speakers.

• Do not expose the device to excessive dust or vibrations, or

extreme cold or heat (such as in direct sunlight, near a

heater, or in a car during the day) to prevent the possibility of

panel disﬁguration or damage to the internal components.

• Do not place the device in an unstable position where it

might accidentally fall over.

• Do not use the device in the vicinity of a TV, radio, stereo

equipment, mobile phone, or other electric devices. Doing so

may result in noise, both in the device itself and in the TV or

radio next to it.

• Before connecting the device to other devices, turn off the

power for all devices. Before turning the power on or off for

all devices, set all volume levels to minimum.

• When turning on the AC power in your audio system, always

turn on monitor speakers LAST, to avoid speaker damage.

When turning the power off, monitor speakers should be

turned off FIRST for the same reason.

• Do not insert your ﬁngers or hands in any gaps or openings

on the device.

•Avoid inserting or dropping foreign objects (paper, plastic,

metal, etc.) into any gaps or openings on the device. If this

happens, unplug the USB cable from the device immediately.

Then have the device inspected by qualiﬁed Yamaha service

personnel.

• Do not use the device or headphones for a long period of

time at a high or uncomfortable volume level, since this can

cause permanent hearing loss. If you experience any hearing

loss or ringing in the ears, consult a physician.

• Do not rest your weight on the device or place heavy objects

on it, and avoid use excessive force on the buttons, switches

or connectors.

Do not open Water warning

Location

Connections

Handling caution

(5)-10 1/2

AUDIOGRAM 3 Owner’s Manual

Always unplug the USB cable from a computer or turn off the computer to turn off the device when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over

time. Consult qualiﬁed Yamaha service personnel about replacing defective components.

SPECIAL NOTICES

• This manual is the exclusive copyright of Yamaha Corporation.

• The included software is the exclusive copyright of Steinberg Media Technologies GmbH.

• Copying of the software or reproduction of this manual in whole or in part by any means is expressly forbidden without the

written consent of the manufacturer.

•Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be

held responsible for the results of the use of this manual and the software.

• This disk containing the software is not meant for use with an audio/visual system (CD player, DVD player, etc.). Do not

attempt to use the disk on equipment other than a computer.

• Future upgrades of application and system software and any changes in speciﬁcations and functions will be announced

separately.

• The screen displays as illustrated in this manual are for instructional purposes, and may appear somewhat different from the

screens which appear on your computer.

The illustrations and LCD screens as shown in this manual are for instructional purposes only, and may appear somewhat

different from those on your instrument.

This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to

which it has license to use others' copyrights. Such copyrighted materials include, without limitation, all computer software,

music data, etc. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant

laws. Any violation of copyright has legal consequences. DON'T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.

• Windows is a registered trademark of Microsoft® Corporation in the United States and other countries.

• Apple, Mac and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries.

• The company names and product names in this manual are the trademarks or registered trademarks of their respective

companies.

* Speciﬁcations and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right

to change or modify products or speciﬁcations at any time without prior notice. Since speciﬁcations, equipment or options

may not be the same in every locale, please check with your Yamaha dealer.

MIC/INST jacks (XLR-type) are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device, or data that is lost

or destroyed.

AUDIOGRAM 3 Owner’s Manual

Introduction.................................................................................... 5

Contents..........................................................................................5

Features..........................................................................................6

Setup............................................................................................... 7

Quick Guide ................................................................................... 8

1. Installing Cubase AI ....................................................................8

2. Connecting to the AUDIOGRAM interface..................................8

3. Powering Up the System ............................................................9

4. Adjusting Level..........................................................................10

5. Recording with Cubase AI ........................................................10

6. Mixing with Cubase AI ..............................................................16

Controls and Functions .............................................................. 18

Input Signal Flow ..........................................................................19

Troubleshooting .......................................................................... 20

Specifications ............................................................................ 128

General Specifications ................................................................128

Dimensional Diagrams................................................................128

Block Diagram and Level Diagram .............................................129

About the accessory disk ......................................................... 130

Introduction

Thank you for choosing a Yamaha AUDIOGRAM 3 Computer Recording System. The AUDIO-

GRAM 3 includes a USB audio interface for digital audio data transfer, and Cubase AI DAW

(Digital Audio Workstation) software for Windows® and Macintosh® computer operating sys-

tems. With the AUDIOGRAM 3 and your personal computer you have the basic elements of a

high-performance computer recording system that is easy to set up and operate.

Please read through this manual carefully before beginning use, so that you will be able to take

full advantage of your interface’s superlative features and enjoy trouble-free operation for years

to come. After reading the manual, please store it in a safe place.

Contents

AUDIOGRAM 3 Owner’s Manual

Connect To Your Computer via a Single USB Cable (page 8)

The AUDIOGRAM interface connects to your computer via the supplied USB cable. Stereo audio

data is transferred in both directions—from the interface to the computer, and vice-versa—via the

USB connection (44.1 kHz or 48 kHz sampling frequency).

No Driver Installation Required (page 8)

The AUDIOGRAM system uses the standard drivers included in your computer’s operating system,

so there’s no need to install any extra driver software.

Cubase AI DAW Software Supplied (page 8)

Cubase AI software, included in the AUDIOGRAM package, offers versatile, high-performance hard-

disk recording capability.

48V Phantom Power (page 18)

A PHANTOM switch supplies +48V phantom power to the channel 1 microphone input, so you can

use high-quality phantom-powered condenser microphones for superior recording quality.

Features

Accessories

• Cubase AI DVD-ROM

• USB cable

• Owner’s Manual (this book)

Introduction

AUDIOGRAM 3 Owner’s Manual

Setup

Be sure to turn the PHANTOM

+48V switch (★) on when

using a phantom-powered

condenser microphone.

Microphone

Keyboard, etc.

Computer

Headphones

Audio system

To connect a device such as a

microphone:

To connect an instrument such

as an electric guitar or bass:

USB cable

Cubase AI

AUDIOGRAM 3 Owner’s Manual

Quick Guide

This quick setup and operation guide covers everything from installing the Cubase AI

software to using Cubase AI for recording and mixdown. While going through this section

you might find it useful to also refer to the “Controls and Functions” section on page 18, as

well as the pdf manual supplied with the Cubase AI software.

You are only permitted to use this software pursuant to the terms and conditions of the

“Steinberg Software End User License Agreement (EULA)” shown during the installation.

Start the computer and log on to the Administrator account.

Insert the included DVD-ROM into the computer’s DVD-ROM drive.

Follow the on-screen instructions to install the Cubase AI software.

• In order to have continuous use of Cubase AI, including support and other beneﬁts, you

will need to register the software and activate your software license by starting it while the

computer is connected to the Internet. Click the “Register Now” button shown when the

software is started, then ﬁll in all required ﬁelds for registration. If you do not register the

product, you will be unable to use the application after a limited period of time expires.

•To install on Mac computers double-click the “Cubase AI*.mpkg” icon or the “Cubase AI*

Start Center” icon.

“*” indicates where the version number appears in the actual icon name.

• Visit the web address below for the latest information on:

<http://www.yamahasynth.com/>

Turn all gear that is to be connected to the AUDIOGRAM off or to standby mode (except the

computer), and set the LEVEL controls and OUT LEVEL control to their minimum settings.

Connect microphones and/or instruments.

For details on making connections refer to the “Setup” section on page 7 and the “Controls and Func-

tions” section on page 18.

Set the MIC/INST switch according to the type of device connected to channel 1.

Select MIC ( ) if a microphone is connected, or INST ( ) if a guitar or similar instrument is connected.

Step

Installing Cubase AI

Step

Connecting to the AUDIOGRAM interface

Important!

NOTE

OUT LEVEL controlLEVEL controls

Be sure to turn the

PHAN-

TOM +48V switch on when

using a phantom-powered

condenser microphone.

Quick Guide

AUDIOGRAM 3 Owner’s Manual

To prevent loud pops and noises, turn on the power to your sound gear starting with the sources

(instruments, CD players, etc.) and ending with the audio system (monitor speakers).

Turn on the instruments and microphones.

If you are using a condenser microphone for the channel 1, turn on the PHANTOM +48V

switch.

Observe the following precautions when turning on phantom power.

• Make sure that the PHANTOM +48V switch is off when phantom power is not

needed.

• When turning the switch on, be sure that only a condenser microphone is con-

nected to the MIC/INST input jack. Other devices may be damaged if connected to

phantom power. This precaution does not apply to balanced dynamic microphones

or instruments with the phone jack, however, as these will not be affected by phan-

tom power.

•To prevent damage to speakers, be sure to turn off audio system (monitor speakers)

before turning this switch on or off. We also recommend that you set the OUT

LEVEL control to the minimum position before operating this switch to avoid the

risk of loud noises that could cause hearing loss or device damage.

Connect the AUDIOGRAM interface to your computer using the supplied USB cable.

The POWER indicator will light to indicate that power is being applied to the AUDIOGRAM interface.

When connecting or disconnecting the USB cable be sure to turn the OUT LEVEL con-

trol all the way down.

The ﬁrst time you connect to the computer’s USB connector, or change the connection

to a different USB port, a driver installation display may appear. If this occurs, wait until

the installation is complete before proceeding.

Turn the power to the audio system (monitor speakers).

Step

Powering Up the System

USB Connection Precautions

Be sure to observe the following points when connecting to the computer's USB interface.

Failure to observe these rules can result in computer freezes/hang-ups and possibly data loss

or corruption. If the instrument or computer does hang up, restart the application or computer.

• Be sure to wake the computer from sleep/suspended/standby mode before

making a connection to the computer’s USB connector.

•Always quit all applications running on the computer before connecting or dis-

connecting the USB cable.

•Wait at least 6 seconds between connecting or disconnecting the USB cable.

CAUTION

NOTE

AUDIOGRAM 3 Owner’s Manual

Quick Guide

Adjust the volume on all instruments that are connected to the AUDIOGRAM interface.

Set the OUT LEVEL control to the minimum position. Failure to do so may result in

loud noise bursts that can damage your equipment, your ears, or both.

Adjust the channel LEVEL controls so that the level indicator PEAK LED ﬂash brieﬂy on

the highest peak levels.

Adjust the overall volume with the OUT LEVEL control while monitoring via headphones

or monitor speakers.

This section describes the procedure for recording to the Cubase AI software we installed earlier via

the AUDIOGRAM interface.

Cubase AI 6 is used for the examples in this manual. For details about other versions of Cubase

AI or Cubase AI operation in general, refer to the PDF manual provided with the software.

Cubase AI Setup

Set the computer output to the maximum level.

For details on how to make the setting refer to the “The recorded sound is too low in level.” section in the

“Troubleshooting” on page 20.

Launch Cubase AI.

Windows:

Click [Start] → [All Program] → [Steinberg Cubase AI *] → [Cubase AI *] to launch the program. (“*”

indicates where the version number appears in the actual icon name.)

If the ASIO Direct Sound Full Duplex Driver dialog window appears, click [OK].

Mac:

Double-click the [Application] → [Cubase AI *]. (“*” indicates where the version number appears in the

actual icon name.)

• If you speciﬁed a ﬁle destination when installing the Cubase AI software, launch the appli-

cation from that location.

• Create a Cubase AI shortcut or alias on your desktop so you can easily launch the pro-

gram when required.

Step

Adjusting Level

Step

Recording with Cubase AI

CAUTION

LEVEL controls

OUT LEVEL control

Level indicator

NOTE

Quick Guide

AUDIOGRAM 3 Owner’s Manual

When the Project Assistant window appears, select the [More] menu → [Empty] and

click [Create].

A new project is created.

Recorded Cubase AI data is stored as a “Project.”.

Select [Device Setup] from the [Devices] menu to open the Device Setup window.

Windows:

Select [VST Audio System] in the [Devices] ﬁeld on the left side of the window. Select [ASIO DirectX

Full Duplex Driver] in the [ASIO Driver] ﬁeld on the right side of the window. A dialog box will appear

asking “Do you want to switch the ASIO driver?”. Click [Switch].

Mac:

Select [VST Audio System] in the [Devices] ﬁeld on the left side of the window. Select [USB Audio

CODEC] in the [ASIO Driver] ﬁeld on the right side of the window. A dialog box will appear asking

“Do you want to switch the ASIO driver?”. Click [Switch].

NOTE

AUDIOGRAM 3 Owner’s Manual

Quick Guide

Select [ASIO DirectX Full Duplex Driver](Windows), [USB Audio CODEC](Mac) in the

[Devices] ﬁeld on the left side of the Device Setup window, and click [Control Panel] on

the right side of the window.

Windows:

The ASIO Direct Sound Full Duplex Setup dialog box will be displayed. Check only the input port and

output port [USB Audio CODEC] checkbox, and then click [OK] to close the dialog window.

Mac:

The [CoreAudio Device Settings] dialog window appears. Check only the [USB Audio CODEC]

checkbox in both “Input” and “Output” of the [Input/Output Conﬁguration] ﬁeld. Click [Close] to close

the dialog window.

Make sure that “USB Audio CODEC 1/2”(Windows), “Front Left/Front Right” (Mac) are

shown in the [Port System Name] ﬁeld, and check the [Visible] column in the Device

Setup window. Click [OK] to close the window.

If the [Port System Name] ﬁeld does not change, close and restart the Cubase AI, then open

the Device Setup window.

NOTE

Quick Guide

AUDIOGRAM 3 Owner’s Manual

Select [VST Connections] from the [Devices] menu.

Windows:

If “Not Connected” is selected in the [Audio Device] ﬁeld, click on the “Not Connected” indication, and

then switch to [ASIO DirectX Full Duplex Driver].

Also set the [Outputs] in the same way, and then close the window.

Mac:

If “Not Connected” is selected in the [Audio Device] ﬁeld, click on the “Not Connected” indication, and

then switch to [USB Audio CODEC].

Also set the [Outputs] in the same way, and then close the window.

Select [Add Track] → [Audio] from the [Project] menu.

The Add Audio Track dialog window appears.

Set the “Count” and “Conﬁguration” parameters, and then click [Add Track].

The added tracks will appear.

You will normally use a stereo track when recording synthesizers, and a monaural track

when recording vocals or guitars.

Preparing to Record

Click in the track list (the area in which the track names are displayed) to select a track

to record on.

The various settings for the selected track are available in the Inspector on the left side of the display.

NOTE

[Record Enable] button

Track list

Inspector

AUDIOGRAM 3 Owner’s Manual

Quick Guide

Make sure the [Record Enable] button for the track to be recorded is turned on.

If the [Record Enable] button is off, click it to turn it on.

Play the instrument to be recorded, and adjust the AUDIOGRAM LEVEL controls so that

the Clipping indicator never lights.

Specify the point at which you want to start recording via the ruler at the top of the win-

dow for the project.

Click the black area of the ruler to move the project cursor (the vertical black line) to that position.

Recording and Playback

Click the Transport panel [Record] button to begin recording.

When recording is started the project cursor will begin moving to the right and a box that displays the

recording results will be created.

Play the part.

When you ﬁnish recording the track, click the Transport panel [Stop] button.

To hear playback of the track you have just recorded, use either the Transport panel [Rewind] button or

the ruler to rewind to the beginning of the recorded section, then click the Transport panel [Start] button.

Clipping indicator

Ruler

Stop

Record

Start

Rewind

Forward

Recording results

Quick Guide

AUDIOGRAM 3 Owner’s Manual

Select [Mixer] from the [Devices] menu to open the Mixer window.

The overall playback level will be displayed via the master section bus level meter on the right side of

the mixer window, and the channel level will be displayed via the channel strip level meter.

To hear the playback sound via the AUDIOGRAM interface, adjust the volume with the OUT

LEVEL control.

The playback level will approximately match the recording level when the computer output is

set to the maximum level.

To save the project select [Save] from the [File] menu and enter a ﬁle name before actu-

ally saving the ﬁle.

Save your project frequently to insure against losing large amounts of data if a problem occurs.

Repeat steps 1 through 5 to record further material on the same track.

To record additional material on a different track, select a new track and repeat the

record procedure.

Recording with maximum quality and minimum noise:

For optimum sound quality with minimum noise, the AUDIOGRAM signal levels should be set as high

as possible without clipping. Check signal levels to be sent to Cubase AI for recording using the

AUDIOGRAM level indicators while the Cubase monitoring button ( ) is turned off. Adjust the chan-

nel LEVEL controls so that the level indicator PEAK LEDs ﬂash only occasionally on the highest input

transients.

NOTE

Level meter Bus level meter

Monitoring button

AUDIOGRAM 3 Owner’s Manual

Quick Guide

In this section we’ll try mixing down multiple recorded audio tracks to stereo, and creating an

audio ﬁle. Mixes can be stored as WAV or AIFF ﬁles, which can then be recorded to audio

CDs.

Launch Cubase AI and open a project ﬁle.

Click the [Start] button on the Transport Panel.

While listening to playback, drag the channel strip level faders up and down to create

the desired initial balance, then adjust the overall volume using the bus volume fader.

Drag the pan controls on the top of the channel strips left and right to set the stereo

position of each track.

At this point you can begin to use EQ to reﬁne your mix, and add effects.

As an example let’s try adding reverb. Click the [Edit] button ( ) on the left side of the channel strip to

open the VST audio channel settings window. Click Inserts 1 and select “Reverb - RoomWorks SE.”

For further details refer to the pdf manual provided with the Cubase AI software.

It’s a good idea to lower the channel fader a bit before adding an effect, since the effect

can cause an increase in the overall channel level.

Step

Mixing with Cubase AI

NOTE

CAUTION

Quick Guide

AUDIOGRAM 3 Owner’s Manual

Double-click the left locator (starting point) and right locator (ending point) of the Trans-

port panel. Change each highlighted number, and then specify the position of the loca-

tor.

When the ﬁnal mix adjustments have been made, go to the [File] menu and select

[Export] → [Audio Mixdown].

Enter a ﬁle name and select a destination for the ﬁle as well as a ﬁle type.

If you intend to use the ﬁle to create an audio CD, select the WAV ﬁle type (AIFF on Mac OS X), 44.1

kHz, and 16 bit.

Click [Export].

Progress of the mixdown operation will be shown in a progress window. When the progress window

closes the mixdown is complete.

Files created by mixdown can be directly played back using the Windows Media Player, or

iTunes.

Bar

NOTE

AUDIOGRAM 3 Owner’s Manual

Controls and Functions

1 PHANTOM +48V Switch/Indicator

This switch toggles phantom power on and

off. If you set the switch on ( ), the

AUDIOGRAM supplies phantom power to

the MIC/INST jack (XLR-type)

8. Turn this

switch on when using a phantom-powered

condenser microphone.

• Be sure to leave this switch off

( ) if you do not need phantom

power.

• When turning the switch on, be

sure that only a condenser micro-

phone is connected to the MIC/

INST input jack. Other devices

may be damaged if connected to

phantom power. This precaution

does not apply to balanced

dynamic microphones or instru-

ments with the phone jack, how-

ever, as these will not be affected

by phantom power.

•To prevent damage to speakers,

be sure to turn off audio system

(monitor speakers) before turn-

ing this switch on or off. We also

recommend that you set the OUT

LEVEL control to the minimum

position. Neglect of these pre-

cautions may result in large

noise bursts that may damage

your equipment, your ears, or

both.

2 MIC/INST Switch

Set this switch according to the type of

device connected. Select MIC ( ) if a

microphone is connected, or INST ( ) if

an electric guitar or bass is connected.

If a device is not connected to the

MIC/INST jack, set this switch to

MIC ( ). Otherwise noise may

occur.

3 LEVEL Controls

Adjusts the level of the channel signal. Use

these controls to adjust the balance

between the channels.

4 POWER Indicator

This indicator lights when power is applied

to the AUDIOGRAM interface via the USB

cable (supplied) that connects it to the

computer.

5 Level Indicators

These indicators show signal levels prior to

the OUT LEVEL control

. The SIGNAL

LED lights when a signal is present, and

the PEAK LED lights when the signal

reaches or exceeds clipping level. Adjust

the input channel LEVEL controls

that the PEAK LEDs ﬂash only brieﬂy on

occasional high-level peaks or not at all.

6 OUT LEVEL Control

Adjusts the signal level sent to the STE-

REO OUT jacks

0. This allows you to

adjust the overall volume without changing

the relative volume balance among the

channels.

When connecting or disconnecting

the USB or audio cables be sure to

turn the OUT LEVEL control all the

way down.

7 USB Connector

Connects the AUDIOGRAM interface to a

USB port on your computer via the sup-

plied USB cable. In addition to transferring

audio data between the AUDIOGRAM

interface and the computer, the USB cable

supplies power from the computer to the

AUDIOGRAM interface.

Yamaha recommends that you

use a USB cable with a length of

1.5 meter or less.

t yee w rq

Control Panel

CAUTION

NOTE

CAUTION

NOTE

Controls and Functions

AUDIOGRAM 3 Owner’s Manual

8 MIC/INST Input Jack

Microphones and instruments such as gui-

tars can be connected here using XLR or

phone jack cables. Set the MIC/INST

switch

2 to MIC or INST according to the

type of device connected.

You can directly connect an elec-

tric guitar or bass without the

need for a separate DI (Direct

Injection) box or amp simulator.

9 LINE Input Jacks

These inputs are intended mainly for use

with instruments and equipment having

stereo outputs, such as a synthesizer or

CD player.

If devices are connected to both phone

and pin jacks, only the signal from the

device connected to the phone jacks is

input.

0 STEREO OUT Jacks

These output the mixed signal from chan-

nels 1 and 2. The output level can be

adjusted using the OUT LEVEL control.

These jacks would typically be connected

to an audio system (monitor speakers).

You can use either the phone jacks

or pin jacks but not both at the

same time. If both jacks are used,

the signal is only output from the

phone jacks.

A PHONES Jack

Connects a pair of headphones to this

jack. The PHONES jack outputs the same

signal as the STEREO OUT jacks.

■ Input Signal Flow

i!1 !0 o

Rear Panel

XLR-type Phone-type

NOTE

Phone-type

Pin-type

NOTE

Input

Output

Adjust the recording level

as well as the balance

between channels.

Adjusts the

monitor level.

Record

Playback

6 OUT LEVEL

control

3 LEVEL

controls

5 Level

indicator

Cubase AI

AUDIOGRAM 3 Owner’s Manual

Troubleshooting

The AUDIOGRAM interface won’t turn on.

❑ Is the included USB cable properly plugged into the interface and a computer?

The system doesn’t work properly.

❑ Are the USB cable and all necessary audio cables properly connected?

❑ Are you using a USB hub?

USB hubs can interfere with proper operation, so try connecting the AUDIOGRAM interface

directly to a USB port on the computer. If the computer has multiple USB ports, try a different

USB port.

❑ Are you using other USB devices at the same time?

If so, try removing the other device(s) and connecting only the Yamaha USB device.

The Input ports are not shown (Windows 7/Vista)

❑ Is the sound input of your computer operating system assigned properly?

1. From the [START] menu click [Control Panel], then double-click the “Sound” icon to open the

“Sound” dialog window.

2. Click the “Recording” tab, right-click the “USB Audio CODEC” icon and select “Properties.”

3. Click the “Advanced” tab, then select “2 channel, 16 bit, 44100 Hz (CD Quality)” or “2 channel,

16 bit, 48000 Hz (DVD Quality)” in the “Default Format” field.

No sound.

❑ Are your speaker cables connected properly, or are they shorted?

❑ Are the volume controls of your sources, audio devices, applications software, computer operat-

ing system, etc., set at appropriate levels?

❑ Is the output of your computer operating system muted?

❑ Do you have several applications running at the same time?

Be sure to quit all applications you are not using.

❑ Is the sound output of your computer operating system assigned properly?

Windows 7/Vista:

1. From the [START] menu click [Control Panel], then double-click the “Sound” icon to open the

“Sound” dialog window.

2. Click the “Playback” tab and check whether the “USB Audio CODEC” icon is checked.

If not, right-click the “USB Audio CODEC” icon and select “Set as Default Device.”

3. Click the [Recording] tab and check whether the “USB Audio CODEC” icon is checked.

If not, right-click the “USB Audio CODEC” icon and select “Set as Default Device.”

Windows XP:

1. From the [START] menu click [Control Panel], then double-click the “Sounds and Audio

Devices” icon to open the “Sounds and Audio Devices Properties” dialog window.

2. Click the “Audio” tab.

3. Set “Sound playback: Default device” and “Sound recording: Default device” to “USB Audio

CODEC.”

4. Click [OK].

Страница загружается ...

Yamaha Audiogram3 Инструкция по применению

Бренд: Yamaha

Модель: Audiogram3

Категория: Аудио-микшеры

Тип: Инструкция по применению

Скачать PDF

сообщить о нарушении

на других языках

English: Yamaha Audiogram3 Owner's manual
français: Yamaha Audiogram3 Le manuel du propriétaire
italiano: Yamaha Audiogram3 Manuale del proprietario
español: Yamaha Audiogram3 El manual del propietario
Deutsch: Yamaha Audiogram3 Bedienungsanleitung
Nederlands: Yamaha Audiogram3 de handleiding
português: Yamaha Audiogram3 Manual do proprietário
dansk: Yamaha Audiogram3 Brugervejledning
polski: Yamaha Audiogram3 Instrukcja obsługi
čeština: Yamaha Audiogram3 Návod k obsluze
svenska: Yamaha Audiogram3 Bruksanvisning
Türkçe: Yamaha Audiogram3 El kitabı
suomi: Yamaha Audiogram3 Omistajan opas
română: Yamaha Audiogram3 Manualul proprietarului

Модели других брендов

Steinberg Cubase Pro 9.0 Инструкция по началу работы

Yamaha Audiogram3 Инструкция по применению

Yamaha Audiogram3 Инструкция по применению

на других языках

Похожие модели бренда

Модели других брендов