Samsung PS58B850Y1W Руководство пользователя

удивительные возможности

Благодарим за приобретение продукта компании

Samsung. Для получения более полного

обслуживания зарегистрируйте свое устройство

по адресу:

www.samsung.ru/club/registration

Модель_______Серийный номер_________

Связывайтесь с SAMSUNG по всему миру

Если у вас есть предложения или вопросы по продуктам Samsung, связывайтесь с информационным центром Samsung.

Country

Customer Care Centre 

Web Site

RUSSIA 8-800-555-55-55 www.samsung.ru

UKRAINE 8-800-502-0000 www.samsung.ua

Плазменный

телевизор

руководство пользователя

BN68-02196D-00

BN68-02196D

PS50B850Y

PS58B850Y

BN68-02196D-Rus.indb 1 2009-4-13 14:02:11

English - 2

User Instructions

Screen Image retention

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more

than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image

retention, reduce the degree of brightness and contrast of the screen when displaying a still image.

Height

The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not

install and operate there.

Heat on the top of the PDP TV

The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper

part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be

prevented from touching the upper part of the product.

The product is making a ‘cracking’ noise.

A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as

temperature or humidity. This is normal and not a defect of the unit.

Cell Defects

The PDP uses a panel consisting of 2,360,000(HD-level) to 6,221,000(FHD-level) pixels which require sophisticated technology to

produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of

the product.

Avoid operating the TV at temperatures below 5°C(41°F)

A still image displayed too long may cause permanent damage to the PDP Panel.

Watching the PDP TV in 4:3 format for a long period of time may leave traces of borders displayed on the left,

right and centre of the screen caused by the difference of light emission on the screen. Playing a DVD or a

game console may cause similar effect to the screen. Damages caused by the above effect are not covered

by the Warranty.

Afterimage on the Screen.

Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages.

To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.

Warranty

Warranty does not cover any damage caused by image retention.

Burn-in is not covered by the warranty.

Installation

Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures,

high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may

cause a serious damage to your set.

Digital TV Notice

1. Functionalities related to Digital TV(DVB) are only available in countries/areas where DVB-T (MPEG2 and MPEG4 AVC)

digital terrestrial signals are broadcasted or where you have access to a compatible DVB-C(MPEG2 and MPEG4 AAC)

cable-TV service. Please check with your local dealer the possibility to receive DVB-T or DVB-C signal.

2. DVB-T is the DVB European consortium standard for the broadcast transmission of digital terrestrial television and DVB-C

is that for the broadcast transmission of digital TV over cable.

However, some differentiated features like EPG (Electric Program Guide), VOD (Video on Demand) and so on, are not

included in this specication. So, they cannot be supported at this moment.

3. Although this TV set meets the latest DVB-T and DVB-C standards[August,2008], the compatibility with future DVB-T digital

terrestrial and DVB-C digital cable broadcasts cannot be guaranteed.

4. Some cable-TV providers may charge an additional fee for such a service and you may be required to agree to terms and

conditions of their business.

5. Some Digital TV functions might be unavailable in some countries or regions and DVB-C might not work correctly with all

providers.

6. For more information, please contact your local Samsung customer care centre.

Contact SAMSUNG WORLDWIDE

If you have any questions or comments relating to Samsung products, please contact the SAMSUNG

customer care centre. (See back cover for more informations.)

Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.

Product design and specications may be changed without notice in order to enhance product performance.

N



-



BN68-02196D-00Eng.indb 2 2009-04-09 오후 4:20:51

English - 3

English

N O T

Symbol Press Note One-Touch Button TOOLS

Contents

Connecting and Preparing Your TV

Checking Parts ..........................................................................4

Using the Stand-Base ..............................................................4

How to assemble the Stand-Base (depending on the model) ... 4

Viewing the Control Panel ......................................................... 5

Viewing the Connection Panel...................................................6

Remote Control ......................................................................... 8

Installing Batteries in the Remote Control ................................. 9

Using the Remote Control Backlight Buttons ............................ 9

Switching On and Off.................................................................9

Placing Your Television in Standby Mode .................................. 9

Viewing the Menus .................................................................. 10

Using the TOOLS Button ........................................................ 10

Plug & Play Feature ................................................................ 11

Channel Control

Storing Channels ................................................................... 12

Managing Channels ................................................................15

Picture Control

Changing the Picture Settings ................................................. 17

Setting up the TV with your PC ............................................... 20

PC Display ...............................................................................21

Sound Control

Changing the Sound Setting ...................................................22

Selecting the Sound Mode ...................................................... 23

Function Description

Setting the Time ......................................................................24

Conguring the Setup Menu ....................................................25

Viewing the Picture in Picture (PIP).........................................27

Support / Input

Supported Program ................................................................. 28

Source List / Edit Name ...........................................................29

Network

Network Connection ................................................................ 30

Network Setup ......................................................................... 33

Media Play

Connecting a USB Device ....................................................... 36

Using the Media Play Function ................................................37

Using and Sorting Photo List ................................................... 38

Viewing a Photo or Slide Show .............................................. 39

Using and Sorting the Music List ............................................. 41

Playing a Music ...................................................................... 42

Using and Sorting the Movie List .............................................43

Playing a Movie File ............................................................... 44

Picture / Music Settings Using Media Play .............................. 46

Using the Setup Menu ............................................................. 47

■

Media Play-DLNA

Setting the DLNA Network .......................................................48

Installing the DLNA Application ...............................................48

Using the DLNA Application ....................................................50

Using the DLNA Function ........................................................ 53

About Anynet+

Connecting Anynet

+

Devices ................................................... 54

Setting Up Anynet

+

................................................................. 55

Switching between Anynet

+

Devices ....................................... 56

Recording ................................................................................ 57

Listening through a Receiver ...................................................57

Troubleshooting for Anynet

+

................................................... 58

Content Library

Activating the Content Library ................................................. 59

Using the Content Library ........................................................60

Internet@TV

Getting Started with Internet@TV ........................................... 61

Setting up Internet@TV ........................................................... 61

Using the Internet@TV service ............................................... 62

Troubleshooting for internet@TV ............................................ 63

Help Website ........................................................................... 63

Home Network Centre

Home Network Centre ............................................................. 64

Setting Up the Home Network Centre ..................................... 65

Using the Message Function ................................................... 66

Using the Media Function ........................................................67

Recommendations for Use

Teletext Feature .......................................................................68

Wall Mount Kit Specications (VESA) ..................................... 69

Preparing before installing Wall- Mount ................................... 70

Securing the TV to the Wall ..................................................... 70

Securing the Installation Space ............................................... 71

Assembling the Cables ............................................................ 72

Troubleshooting ....................................................................... 73

Specications .......................................................................... 74

Software License ..................................................................... 75

■

BN68-02196D-00Eng.indb 3 2009-04-09 오후 4:20:51

English - 4

Checking Parts

Owner’s Instructions Remote Control/

AAA Batteries (2ea)

Program CD

Cloth-Clean Holder-Ring (4ea)

(Refer to page 70)

Warranty Card/

Safety Guide Manual

(Not available in all

locations)

Cover-Bottom

(PS50B850Y only)

Screws (5ea)

(PS50B850Y only)

Cover-Bottom/Screw

(PS58B850Y only)

Holder-Wire stand

(Refer to page 72)

Holder-Wire (3ea)

(Refer to page 72)

Ferrite Core (4ea)

AV Cable Component Cable Ext Cable Holder-Wire Cable

(Refer to page 73)

Ferrite Core

The ferrite cores are used to shield the cables from interference.

When connecting a cable, open the ferrite core and clip it around

the cable near the plug.

N

Connecting and Preparing Your TV

Using the Stand-Base

Two or more people should carry the PDP. Never lay the PDP on the oor

because of possible damage to the screen. Always keep the PDP upright.

The PDP can rotate 20 degrees in right and left directions.

N

How to assemble the Stand-Base (depending on the model)

Using the 5 screws for securing the stand base and the TV, firmly attach the TV

to the stand base.

(The exterior of the set may be different than the picture.)

In case of installing your TV on the wall, close the

cover (1) on the stand-base connection part using

two screws for hiding.

Warning

Firmly secure the stand to the TV before moving

it, as the stand may fall and could cause serious

injury.

Two or more people should carry the TV.

Never lay the TV on the oor because of

possible damage to the screen.

Always store the TV upright.

N

Power Cord (2ea) LAN Cable

(1ea)

HDMI Cable

(1ea)

-20° ~ 20°

BN68-02196D-00Eng.indb 4 2009-04-09 오후 4:20:56

English - 5

Viewing the Control Panel

The product colour and shape may vary depending on the model.

N

Front Panel buttons

Touch each button to

operate.

1

REMOTE CONTROL SENSOR

Aim the remote control towards this spot on the TV.

2

SOURCE

Toggles between all the available input sources

(TV, AV, Component, PC, HDMI1/DVI, HDMI2, HDMI3,

HDMI4, USB).

In the on-screen menu, use this button as you would use

the ENTER

E

button on the remote control.

3

MENU

Press to see an on-screen menu of your TV’s features.

4

+ VOL –

Press to increase or decrease the volume. In the on-screen

menu, use the + VOL – buttons as you would use the

◄ and ► buttons on the remote control.

N

5

Press to change channels. In the on-screen menu, use the

buttons as you would use the ▲ and ▼ buttons

on the remote control. You can use button to turn

on the TV without the remote control.

6

POWER INDICATOR

Blinks and turns off when the power is on and lights up in

stand-by mode.

7

(

POWER)

Press to turn the TV on and off.

8

SPEAKERS

BN68-02196D-00Eng.indb 5 2009-04-09 오후 4:20:58

English - 6

Viewing the Connection Panel

TV Rear Panel

Whenever you connect an audio or video system to your set, ensure that all elements are switched off.

When connecting an external device, match the colour of the connection terminal to the cable.

N

The product colour and shape may vary depending on the model.

N

987

Cable Television

Network

or

0

4 53

@



4

2

or

!

6

1

BN68-02196D-00Eng.indb 6 2009-04-09 오후 4:21:01

English - 7

1

COMMON INTERFACE Slot

Insert CI (Common Interface) card into the slot.

(refer to page 27)

When not inserting CI CARD in some channels, Scramble

Signal is displayed on the screen.

The pairing information containing a telephone number, CI

CARD ID, Host ID, and other information will be displayed

in about 2~3 minutes. If an error message is displayed,

please contact your service provider.

When the channel information conguration has nished,

the message Updating Completed is displayed, indicating

that the channel list is now updated.

Insert the CI-Card in the direction marked on it.

CAM is not supported in some countries and

regions,check with your authorized dealer.

2

USB 1 (HDD), USB 2

Connect a USB mass storage device to view photo les

(JPEG), play audio les (MP3) and movie les.

You can connect to SAMSUNG’s network wirelessly.

The USB 1 (HDD) port is also used as the HDD.

HDD (Hard disk drive) is device which stores digitally

encoded data

3

POWER IN

Connect the supplied power cord.

4

LAN

Connect a LAN cable to this port to connect to the Network

(SAMSUNG's Internet@TV Service).

5

ANT IN

75Ω Coaxial connector for Aerial/Cable Network.

6 EXT (RGB)

Inputs or outputs for external devices, such as VCR, DVD,

video game device or video disc players.

In EXT mode, DTV Out only supports MPEG SD Video

and Audio.

In EXT Mode, Game mode is not available

Input/Output Specification

Connector

Input Output

Video Audio(L/R) RGB Video + Audio(L/R)

EXT ✔ ✔ ✔

Only TV or DTV output

is available.

7

AV IN (AUDIO L/R / VIDEO)

-

N

Video and audio inputs for external devices, such as a

camcorder or VCR.

8

COMPONENT IN

Audio (AUDIO L/R) and video (Y/PB/PR) inputs for Component.

9

PC IN / PC/DVI AUDIO IN

Connect to the video and audio output jack on your PC.

0

HDMI IN 1 (DVI), 2, 3, 4

No additional Audio connection is needed for an HDMI to

HDMI connection.

Whenusing an HDMI/DVI cable connection, you must use

the HDMI IN 1 (DVI) jack.

What is HDMI?

High Definition Multimedia interface allows the

transmission of high denition digital video data and

multiple channels of digital audio.

The HDMI/DVI terminal supports DVI connection to

an extended device with the appropriate cable (not

supplied). The difference between HDMI and DVI is

that the HDMI device is smaller in size, has the HDCP

(High Bandwidth Digital Copy Protection) coding feature

installed, and supports multi - channel digital audio.

We recommend using HDMI cables no more than 14mm

wide.

PC/DVI AUDIO IN

DVI audio outputs for external devices.

Supported modes for HDMI/DVI and Component

480i 480p 576i 576p 720p 1080i 1080p

HDMI/DVI 50Hz X X X O O O O

HDMI/DVI 60Hz X O X X O O O

Component O O O O O O O

! SERVICE

Connector for service.

@

DIGITAL AUDIO OUT (OPTICAL)

Connect to a Digital Audio Component.

-

N

-

N

BN68-02196D-00Eng.indb 7 2009-04-09 오후 4:21:02

English - 8

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV.

The performance of the remote control may be affected by bright light.

N

1

POWER button

(turns the TV on and off)

2

Selects the TV mode directly.

3

Number buttons for direct channel

access.

4

Use to select on-screen menu items

5

Use to display Channel Lists on the

screen.

6

Displays the main on-screen menu.

7

Use to quickly select frequently used

functions.

8

Use to select on-screen menu items

and change menu values.

9

This function enables you to view

Internet@TV.

0

Use these buttons in the Channel list,

Media Play, and Internet@TV, etc.

!

Available source selection

@

Volume increase

Volume decrease

$

Use to see information on the current

broadcast.

%

Digital subtitle display

^

Use these buttons in the Anynet+ and

Media Play.

&

Press to backlight the buttons on the

remote. This function is convenient

for using at night or when the room is

dark. (Using the remote control with

the ON/OFF( ) light button set to On

will reduce the battery usage time.)

*

Previous channel

(

Press to switch to your favorite

channels.

)

Returns to the previous menu.

a

Exit the on-screen menu.

b

Next channel

Previous channel

c

Temporary sound switch-off.

d

This function enables you to view

Content Library.

e

This function enables you to view and

play photo, music and movie les from

an external device.

(Refer to pages 38 (Photo), 41 (Music),

and 43 (Movie))

f

Electronic Program Guide (EPG)

display

Teletext Functions

2

Exit from the teletext display

(depending on the model)

5

Teletext store

6

Teletext index

7

Teletext size

0

Fastext topic selection

!

Teletext mode selection (LIST/FLOF)

#

Teletext display/mix both

teletext information and the normal

broadcast

$

Teletext reveal

*

Teletext sub page

)

Teletext hold

a

Teletext cancel

b

P :Teletext next page

P :Teletext previous page

BN68-02196D-00Eng.indb 8 2009-04-09 오후 4:21:02

English - 9

Installing Batteries in the Remote Control

1. Lift the cover at the back of the remote control upward as shown in the gure.

2. Install two AAA size batteries.

Make sure to match the ‘+’ and ‘–’ ends of the batteries with the diagram inside

the compartment.

3. Close the cover.

Remove the batteries and store them in a cool, dry place if you won’t be using the

remote control for a long time.

If the remote control doesn’t work, check the following

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power outage or is the power cord unplugged?

5. Is there a special uorescent light or neon sign nearby?

N

Using the Remote Control Backlight Buttons

Use this feature in dark surroundings and when you are unable to see the remote control buttons clearly.

1. Press the ON/OFF( ) light button

When ON, the button backlight is turned on for a moment.

Pressing a remote control button when the remote control is on turns the button backlight on for a moment. If you touch or move

the remote control and the motion is detected by the sensor of the remote control, the button backlight will be turned on for a

moment.

Since there is a vibrating device inside the remote control, shaking the remote control will result in a sound generated by the

device.

The button backlight will not be turned on when the remote control is turned off.

Switching On and Off

The mains lead is attached to the rear of your set.

1. Plug the mains lead into an appropriate socket.

The standby indicator lights up on your set.

2. Press the POWER

P

button on your set.

You also can press the POWER

P

button or the TV button on the remote control to

turn the TV on.

The programme that you were watching last is reselected automatically.

3. Press the numeric button (0~9) or channel up / down (

<

/

>

) button on the remote control or

<

CH

>

button on your set.

When you switch the set on for the very rst time, you will be asked to choose language in which the menus are to be displayed.

4. To switch your set off, press the POWER

P

button again.

Placing Your Television in Standby Mode

Your set can be placed in standby mode in order to reduce the power consumption. The standby mode can be useful when you wish to

interrupt viewing temporarily (during a meal, for example).

1. Press the POWER

P

button on the remote control.

The screen is turned off and a red standby indicator appears on your set.

2. To switch your set back on, simply press the POWER

P

, numeric buttons (0~9), TV button or channel up / down (

<

/

>

) button

again.

Do not leave your set in standby mode for long periods of time (when you are away on holiday, for example). It is best to unplug

the set from the mains and aerial.

N

BN68-02196D-00Eng.indb 9 2009-04-09 오후 4:21:03

English - 10

Viewing the Menus

1. With the power on, press the MENU button. The main menu appears on the

screen. The menu’s left side has icons: Picture, Sound, Channel, Setup, Input,

Application, Support.

2. Press the ▲ or ▼ button to select one of the icons. Then press the ENTER

E

button to access the icon’s sub-menu.

3. Press the EXIT button to exit.

The on-screen menus disappear from the screen after about one minute.

Using the TOOLS Button

You can use the TOOLS button to select your frequently used functions quickly and

easily. The Tools menu changes depending on which external input mode you are

viewing.

1. Press the TOOLS button. The Tools menu will appear.

2. Press the ▲ or ▼ button to select a menu, then press the ENTER

E

button.

3. Press the ▲ / ▼ / ◄ / ► / ENTER

E

buttons to display, change, or use the selected

items. For a more detailed description of each function, refer to the corresponding page.

Anynet

+

(HDMI-CEC), see page 55

Picture Size, see page 18

Picture Mode, see page 17

Sound Mode, see page 22

Sleep Timer, see page 24

SRS TS HD, see page 22

Energy Saving, see page 26

Dual l ll, see page 23

Add to Favourite (or Delete from Favourite), see page 15

PIP, see page 27

Auto Adjustment, see page 20

•

N

Tools

Anynet+ (HDMI-CEC)

Picture Size : Auto Wide

Picture Mode : Standard

Sound Mode : Custom

Sleep Timer : Off

SRS TS HD : Off

Energy Saving : Off

Dual l ll : Mono

Add to Favourite

U

Move

E

Enter

e

Exit

Mode

:

Standard

Cell Light : 4

Contrast : 95

Brightness : 45

Sharpness : 50

Colour : 50

Tint (G/R) : G50/R50

Advanced Settings

Picture

BN68-02196D-00Eng.indb 10 2009-04-09 오후 4:21:04

English - 11

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently.

The Screen Saver is activated if there is no remote control key input for longer than 1 minute while Plug & Play is running.

The Screen Saver is activated if there is no operating signal for longer than 15 minutes.

If you accidentally select the wrong country for your TV, the characters on the screen may be wrongly displayed.

1. Press the POWER button on the remote control. Select the OSD Language. menu

is automatically displayed. Select the appropriate language by pressing the ▲ or ▼

button. Press the ENTER

E

button to conrm your choice.

2. Press the ◄ or ► button to select Store Demo or Home Use, then press the

ENTER

E

button.

We recommend setting the TV to Home Use mode for the best picture in your

home environment.

Store Demo mode is only intended for use in retail environments.

If the unit is accidentally set to Store Demo mode and you want to return to Home Use (Standard): Press the Volume button on

the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.

3. Press the ENTER

E

. Select the appropriate country by pressing the ▲ or ▼ button. Press the ENTER

E

button to conrm your

choice.

4. Press the ▲ or ▼ button to memorize the channels of the selected connection, then press the ENTER

E

button.

Air: Air antenna signal.

Cable: Cable antenna signal.

5. Press the ▲ or ▼ button to select the Antenna source to memorize. Press the ENTER

E

button to select Start.

Digital & Analogue: Digital and Analogue channels.

Digital: Digital channels.

Analogue: Analogue channels.

The channel search will start and end automatically.

For more detailed description of selecting Cable mode, refer to page 12.

6. The message Set the Clock Mode is displayed. Press the ENTER

E

button. Press the ▲ or ▼ button to select Auto, then press

the ENTER

E

button.

If you select Manual, Set current date and time is displayed. (For a more detailed description of Manual, refer to page 24)

If you have received a digital signal, the time will be set automatically.

7. The brief instruction on How to get the best performance from your new HDTV is displayed. Press the ENTER

E

button.

This menu is available HD Connection Guide in the Support menu.

You can change previous or next page by pressing the ◄ / ► button.

8. The message Enjoy your TV. is displayed.

If you want to view the TV immediately, select the Watch TV.

If you want to view the See Product Guide, press the ENTER

E

button.

If you want to reset this feature...

1. Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup,

then press the ENTER

E

button.

2. Press the ENTER

E

button again to select Plug & Play.

3. Enter your 4 digit PIN number. The default PIN number of a new TV set is ‘0-0-0-0’.

If you want to change PIN(Personal Identication Number), refer to page 25.

The Plug & Play feature is only available in the TV mode.

N

•

N

Plug & Play

Select the OSD Language.

Language :

E

Enter

▲

Nederlands

English

Eesti

▼

Setup

Plug & Play ►

Language : English

Time

Game Mode : Off

BD Wise : On

Network Type : Cable

Network Setup

Child Lock : On

BN68-02196D-00Eng.indb 11 2009-04-09 오후 4:21:04

English - 12

Storing Channels

Country

Digital Channel: You can change the country for digital channels.

Analogue Channel: You can change the country for analogue channels.

The PIN number input screen appears. Enter your 4 digit PIN number.

Auto Store

Scans for all channels with active broadcast stations (and availability depends on your

country) and stores them in the TV's memory.

You set the TV to memorize the channels of the selected connection.

Air: Air antenna signal.

Cable: Cable antenna signal.

You can select the antenna source to memorize.

Digital & Analogue: Digital and Analogue channels.

Digital: Digital channels.

Analogue: Analogue channels.

When selecting Cable,

Search Mode: Displays the search mode. (Quick)

- Network ID: Displays the network identication code.

- Frequency: Displays the frequency for the channel.

- Modulation: Displays available modulation values.

- Symbol Rate: Displays available symbol rates.

Search Mode: Displays the search mode.(Full, Network)

- Start Frequency: Displays the frequency start values.

- End Frequency: Displays the frequency stop values.

- Modulation: Displays available modulation values.

- Symbol Rate : Displays available symbol rates.

For more detailed description of Full search mode, refer to page 13.

If you want to stop Auto Store, press the ENTER

E

button.

The Stop Auto Store? message will be displayed.

Select Yes by pressing the ◄ or ► button, then press the ENTER

E

button.

❑



N

❑

•

N

•

N

Channel Control

Continued...

Channel

Country ►

Auto Store

Manual Store

Cable Search Option

Full Guide

Mini Guide

Default Guide : Full Guide

Channel List

BN68-02196D-00Eng.indb 12 2009-04-09 오후 4:21:04

English - 13

Manual Store

Scans for a channel manually and stores it in the TV’s memory.

Digital Channel (Digital)

Digital Channel is only available in DTV mode.

Channel: Set the Channel number using the ▲, ▼ or number (0~9) buttons.

Frequency: Set the frequency using the number (0~9) buttons.

Bandwidth: Set the bandwidth using the ▲ or ▼ buttons.

When it has nished, channels are updated in the channel list.

Analogue Channel

Manual store for analogue channel.

Programme (Programme number to be assigned to a channel): Sets the programme number using the ▲, ▼ or number (0~9)

buttons.

Colour System → Auto / PAL / SECAM / NTSC 4.43: Sets the colour system value using the ▲ or ▼ button.

Sound System → BG / DK / I / L : Sets the sound system value using the ▲ or ▼ button.

Channel (When you know the number of the channel to be stored): Press the ▲ or ▼ button to select C (Air channel) or S

(Cable channel). Press the ► button, then press the ▲, ▼ or number (0~9) buttons to select the required number.

If there is abnormal sound or no sound, reselect the sound standard required.

Search (When you do not know the channel numbers): Press the ▲ or ▼ button to start the search. The tuner scans the

frequency range until the rst channel or the channel that you selected is received on the screen.

Store (When you store the channel and associated programme number): Set to OK by pressing the ENTER

E

button.

Channel mode

- C (Air channel mode):

You can select a channel by entering the assigned number to each air broadcasting station in this mode

.

- S (Cable channel mode): You can select a channel by entering the assigned number for each cable channel in this mode.

Cable Search Option

You can set additional search options such as frequency and symbol rate for cable network searching. (Depending on the each

country)

Freq.Start : Displays the frequency start values.

Freq.Stop : Displays the frequency stop values.

Modulation: Displays available modulation values.

Symbol Rate: Displays available symbol rates.

If the Freq.Start value is bigger than Freq.Stop value, the warning message is displayed.

Full Guide / Mini Guide

The EPG (Electronic Programme Guide) information is provided by the broadcasters. Programme entries may appear blank or out

of date as a result of the information broadcast on a given channel. The display will dynamically update as soon as new information

becomes available.

Full Guide: Displays the programme information as time ordered one hour segments. One hours of programme information is

displayed which may be scrolled forwards or backwards in time.

Mini Guide: The information of each programme is displayed by each line on the current channel Mini Guide screen from the

current programme onwards according to the programme starting time order.

❑



N

•

N



•

N

•

N

❑

•

N

❑

•

Continued...

BN68-02196D-00Eng.indb 13 2009-04-09 오후 4:21:05

English - 14

Default Guide

Mini Guide / Full Guide

You can decide whether to display either the Mini Guide or the Full Guide when the

GUIDE button on the remote control is pressed.

You can also display the guide menu simply by pressing the GUIDE button.

Using the Full / Mini Guide

▲ / ▼ / ◄ / ►

,

ENTER

Select a programme by pressing the ▲/▼/◄/►/ENTER

E

button.

RED Toggle between the Mini Guide or Full Guide.

GREEN

Full Guide: Scroll backwards quickly (-24 hours).

Mini Guide: Display previous page quickly.

YELLOW

Full Guide: Scroll forwards quickly (+24 hours).

Mini Guide: Display next page quickly.

BLUE Exit the guide.

INFO INFO button for the detailed information.

Channel Mode

When the press the P (</>) button, Channels will be switched within the selected channel list.

Added Ch.:

Channels will be switched within the memorized channel list.

Favourite Ch.:

Channels will be switched within the favourite channel list.

Fine Tune (Analogue channel only)

If the reception is clear, you do not have to ne tune the channel, as this is done automatically during the search and store

operation. If the signal is weak or distorted, you may have to ne tune the channel manually.

Fine tuned channels that have been saved are marked with an asterisk * on the right-hand side of the channel number in the

channel banner.

If you do not store the ne-tuned channel in memory, adjustments are not saved.

To reset the ne-tuning, select Reset by pressing the ▼ button and then press the ENTER

E

button.

❑



O

❑



❑

N

Channel

Full Guide

Mini Guide

Default Guide : Full Guide ►

Channel Mode

Channel List

Channel Mode : Added Ch.

Fine Tune

Full Guide

DTV Cable 900 f tn 2:10 Tue 1 Jun

Freshmen On Campus

2:00 - 2:30

No Detailed Information

Today 2:00 - 3:00 3:00 - 4:00

Mint Extra

Loaded

Fresh 40 with Dynamite MC

The Distillery

Smash Hits! Sunday

900 f tn

901 ITV Play

902 Kerrang!

903 Kiss

903 oneword

903 Smash Hits!

▼

Street Hypn..

Kisstory

No Information

Freshmen O..

Mini Guide DTV Cable 900 f tn

Street Hypnosis

Booze Britain

2:00

2:30

5:00

▼

Freshmen On Campus

Watch

INFO

Information



Mini Guide



+24 Hours



Exit

Watch

INFO

Information



Full Guide



Exit

BN68-02196D-00Eng.indb 14 2009-04-09 오후 4:21:05

English - 15

Managing Channels

Using this menu, you can Add / Delete or set Favourite channels and use the programme

guide for digital broadcasts.

Select a channel in the All Channels, Added Channels, Favourites, or Programmed

screen by pressing the ▲ or ▼ buttons, and pressing the ENTER

E

button.

Then you can watch the selected channel.

All Channels: Shows all currently available channels.Shows all currently available channels.

Added Channels: Shows all added channels.Shows all added channels.

Favourites: Shows all favourite channels.Shows all favourite channels.

Programmed: Shows all current reserved programmes.Shows all current reserved programmes.

Press the CH LIST button on the remote control to bring up the channel lists.

Using the Colour buttons with the Channel List

Red (Channel Type): Toggle between your TV, Radio, Data/Other and All.

Green (Zoom): Enlarges or shrinks a channel number.

Yellow (Select): Selects multiple channel lists.

T

TOOLS (Tools): Displays the Delete (or Add), Add to Favourite (or Delete from

Favourite), Lock (or Unlock), Timer Viewing, Edit Channel Name, Edit Channel

Number, Sort, Select All (or Deselect All), or Auto Store menu.

(The Tools menus may differ depending on the situation.)

Channel Status Display Icons

A

An Analogue channel.

c

A channel selected by pressing the

yellow button.

♥

A channel set as a Favourite.

(

A programme currently being

broadcast.

\

A locked channel.

)

A reserved programme

Channel List Tools Menu (in All Channels / Added Channels / Favourites)

Press the TOOLS button to use the Tools menu.

The Tools menu items may differ depending on the channel status.

Add / Delete

You can delete or add a channel to display the channels you want.

All deleted channels will be shown on All Channels menu.

A gray-coloured channel indicates the channel has been deleted.

The Add menu only appears for deleted channels.

You can also delete a channel to the Added Channels or Favourites menu in the

same manner.

Add to Favourite / Delete from Favourite

You can set channels you watch frequently as favourites.

Press the TOOLS button to display Tools menu.

You can also add the favourite channel by selecting Tools → Add to Favourite

(or Delete from Favourite).

T

To select the Favourite channels you have set up, press the FAV.CH button on the

remote control.

The “♥” symbol will be displayed and the channel will be set as a favourite.

All favourite channels will be shown on Favourite menu.

Lock / Unlock

You can lock a channel so that the channel cannot be selected and viewed. This function is available only when the Child Lock is

set to on. (see page 25)

The PIN number input screen appears. Enter your 4 digit PIN number.

The default PIN number of a new TV set is ‘0-0-0-0’. You can change the PIN, by selecting Change PIN from the menu.

The “\” symbol will be displayed and the channel will be locked.

N

•

O

N

-

N

❑

N



N



O

N



N

Continued...

Channel

Mini Guide

Default Guide : Full Guide

Channel List

Channel Mode : Added Ch.

Fine Tune

824 UKTV Gold

825 UKTV style

A

1 C --

A

2 C

--

A

3

♥

C

--

A

4 C

--

A

5 C

--

A

6 C

--

A

7 C

--

A

8 C

--

All Channels

All



Channel Type



Zoom



Select

Tools

824 UKTV Gold

825 UKTV style

A

1 C --

A

2 C

--

A

3

C

--

A

4 C

--

A

5 C

--

A

6 C

--

A

7 C

--

A

8 C

--

All Channels

All



Channel Type



Zoom



Select

Tools

Delete

Add to Favourite

Lock

Timer Viewing

Edit Channel Name

Sort

▼

BN68-02196D-00Eng.indb 15 2009-04-09 오후 4:21:06

English - 16

Timer Viewing

If you reserve a programme you want to watch, the channel is automatically switched to the reserved channel in the Channel List;

even when you are watching another channel. To reserve a programme set the current time rst. (See page 24)

Only memorized channels can be reserved.

You can set the channel, month, day, year, hour and minute directly by pressing the number buttons on the remote control.

Reserving a programme will be shown on Programmed menu.

Digital Programme Guide and Viewing Reservation

When a digital channel is selected, and you press the ► button, the Programme Guide for the channel appears.

You can reserve a programme according to the procedures described above.

Edit Channel Name (Analogue channel only)

Channels can be labeled so that their call letters appear whenever the channel is selected.

The names of digital broadcasting channels are automatically assigned and cannot be labeled.

Edit Channel NumberNumber (Analogue channel only)

You can also edit the channel number by pressing the number buttons on the remote control.

Sort (Analogue channel only)

This operation allows you to change the programme numbers of the stored channels. This operation may be necessary after using

the auto store.

Select All / Deselect All

You can deselect or select all channels in the channel list.

You can perform the Add / Delete, Add to Favourites / Delete from Favourites, or Lock / Unlock function for multiple channels at

the same time. Select the required channels and press the yellow button to set all the selected channels at the same time.

The c mark appears to the left of the selected channels.

You can only select Deselect All when there is a selected channel.

Auto Store

For further details on setting up options, refer to page 12.

If a channel is locked using the Child Lock function, the PIN input window appears.

Channel List Tools Menu (in Programmed )

You can view, modify or delete a reservation.

Press the TOOLS button to use the Tools menu.

Change Info: Select to change a viewing reservation.

Cancel Schedules: Select to cancel a viewing reservation.

Information: Select to view a viewing reservation. (You can also change the reservation

information.)

Select All / Deselect All: Select or deselect all reserved programmes.



N



N



N



N

❑

N

•

Programmed

1 / 1 / 2009

13:59 5 TV1 Quincy, M.E

18:59 2 TV3 The Equalizer

20:59 2 TV3 McMillan & Wife

21:59 2 TV3 M.Spillane’s mike Hammer

Change Info

Cancel Schedules

Information

Select All

All



Zoom



Select

Tools

Information

BN68-02196D-00Eng.indb 16 2009-04-09 오후 4:21:07

English - 17

Changing the Picture Settings

Mode

You can select the type of picture which best corresponds to your viewing requirements.

Dynamic / Standard / Eco / Movie

Press the TOOLS button to display Tools menu.

You can also set the picture mode by selecting Tools → Picture Mode.

T

When in PC mode, Eco is not available.

Cell Light / Contrast / Brightness / Sharpness / Colour / Tint (G/R)

Your television has several setting options that allow you to control the picture quality.

Cell Light: Adjusts the pixel brightness.

Contrast: Adjusts the contrast level.

Brightness: Adjusts the brightness level.

Sharpness: Adjusts the sharpness.

Colour: Adjusts the colour saturation of the picture using the bar on the screen.

Tint (G/R): Adjusts the colour tint of the picture.

When you make changes to Cell Light, Contrast, Brightness, Sharpness, Colour or Tint (G/R), the OSD will be adjusted

accordingly.

The adjusted values are saved for each picture mode.

In Analogue TV, Ext., AV modes of the PAL system, you cannot use the Tint Function.

In PC mode, you can only make changes to Cell Light, Contrast and Brightness.

Each adjusted setting will be stored separately according to its input mode.

The energy consumed during use can be signicantly reduced if the level of brightness of the picture is reduced, and then this

will reduce the overall running cost.

Advanced Settings

You can adjust the advanced settings for your screen including the colour and contrast.

Advanced Settings is available in Standard or Movie mode.

In PC mode, you can only make changes to Dynamic Contrast, Gamma and

White Balance from among the Advanced Settings items.

Black Tone →→ Off / Dark / Darker / Darkest

You can enhance the picture depth by adjusting the black colour density.

Dynamic Contrast →→ Off / Low / Medium / High

You can adjust the screen contrast so that the optimal contrast is provided.

Gamma

You can adjust the primary colour (Red, Green, Blue) Intensity.

Colour Space

Colour Space is a colour matrix composed of red, green and blue colours. Select your favourite Colour Space to experience the

most natural colour.

Auto: Automatically sets the colour range depending on the input video source.

Native: Sets the colour range wider than the that of the input video source.

Custom: Adjusts the colour range to suit your preference.

Customizing the Colour Space

- Adjusts the Colour range to suit your preference. Colour is available when Colour Space is set to Custom.

- Colour →→ Red / Green / Blue / Yellow / Cyan / Magenta

- Red / Green / Blue: You can adjust the RGB values for the selected colour.

- Reset: Resets the colour space to the default values.

White Balance

You can adjust the colour temperature for more natural picture colours.

R-Offset / G-Offset / B-Offset / R-Gain / G-Gain / B-Gain: Changing the adjustment value will refresh the adjusted screen.

Reset: Resets the default white balance.

❑



N

❑

•

N

❑

N



•

N



•

Picture Control

Continued...

Mode : Standard ►

Cell Light : 4

Contrast : 95

Brightness : 45

Sharpness : 50

Colour : 50

Tint (G/R) : G50/R50

Advanced Settings

Picture

Colour : 50

Tint (G/R) : G50/R50

Advanced Settings ►

Picture Options

Picture Reset

Picture

BN68-02196D-00Eng.indb 17 2009-04-09 오후 4:21:07

English - 18

Flesh Tone

You can adjust the esh tone to be more or less red.

Changing the adjustment value will refresh the adjusted screen.

Edge Enhancement →→ Off / On

You can emphasize object boundaries in the picture.

xvYCC → Off / On

Setting the xvYCC mode to on increases detail and colour space when watching movies from an external device (i.e. DVD player).

xvYCC is available when the picture mode is set to Movie, and the external input is set to HDMI or Component mode.

Picture Options

You can customize the additional picture settings to suit your preference.

In PC mode, you can only make changes to the Colour Tone, Size and Screen

Burn Protection from among the items in Picture Options.

Colour Tone →→ Cool / Normal / Warm1 / Warm2 / Warm3

You can select the most comfortable colour tone to your eyes.

The adjusted values are stored according to the selected Picture mode.

Warm1, Warm2, or Warm3 is only activated when the picture mode is Movie.

Size → Auto Wide / 16:9 / Wide Zoom / Zoom / 4:3 / Screen Fit

You can select the picture size which best corresponds to your viewing requirements.

Auto Wide: Sets the picture in Auto Wide format.

16:9: Sets the picture to the 16:9 aspect ratio.

Wide Zoom: Select this menu to view 4:3 aspect ratio pictures over a 16:9 aspect ratio TV by stretching the 4:3 picture

vertically.

Zoom: Stretches the 16:9 aspect ratio picture vertically.

4:3: Sets the picture to the 4:3 aspect ratio.

Screen Fit: Displays the full native HD signal that cannot be viewed using a normal TV.

Depending on the input source, the picture size options may vary.

The items available may differ depending on the selected mode.

In PC Mode, only 16:9 and 4:3 mode can be adjusted.

When Double ( , ) mode has been set in PIP, the Picture Size cannot be set.

Settings can be adjusted and stored for each external device you have connected to an input of the TV.

Temporary image retention may occur when viewing a static image on the set for more than two hours.

Wide Zoom: Press the ► button to select Position, then press the ENTER

E

button.

Press the ▲ or ▼ button to move the screen up / down. Then press the ENTER

E

button.

Zoom: Press the ► button to select Position, then press the ENTER

E

button. Press the ▲ or ▼ button to move the

picture up and down. Then press the ENTER

E

button. Press the ► button to select Size, then press the ENTER

E

button.

Press the ▲ or ▼ button to magnify or reduce the picture size in the vertical direction. Then press the ENTER

E

button.

After selecting Screen Fit in HDMI (1080i / 1080p) or Component (1080i / 1080p) mode: Select Position by pressing

the ◄ or ►button. Use the ▲, ▼, ◄ or ► button to move the picture.

Reset: Press the ◄ or ► button to select Reset, then press the ENTER

E

button. You can initialize the setting.

If you use the Screen Fit function with HDMI 720p input, 1 line will be cut at the top, bottom, left and right as in the overscan

function.

Screen Mode → 16:9 / Wide Zoom / Zoom / 4:3

When setting the picture size to Auto Wide in a 16:9 wide TV, you can determine the picture size you want to see the 4:3 WSS

(Wide Screen Service) image or nothing. Each individual European country requires different picture size so this function is

intended for users to select it.

This function is available in Auto Wide mode.

This function is not available in PC, Component or HDMI mode.

Digital NR →→ Off / Low / Medium / High / Auto

If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static

and ghosting that may appear on the screen.

When the signal is weak, select one of the other options until the best picture is displayed.

HDMI Black Level →→ Normal / Low

You can directly select the black level on the screen to adjust the screen depth.

This function is active only when the external input connects to HDMI (RGB signals).



N



N

❑

N



N



•

N



N



N



N

Continued...

Tint (G/R) : G50/R50

Advanced Settings

Picture Options ►

Picture Reset

Picture

BN68-02196D-00Eng.indb 18 2009-04-09 오후 4:21:07

English - 19

1080 Full HD Motion Demo → Off / On

Samsung's new generation PDP panels deliver stunning Full HD motion clarity when viewing fast action sports, movies, and games.

This function is not available in PC, Game or Media Play mode.

Film Mode

You can optimize the picture mode for watching movies.

Off: Turn the Film Mode function off.

Auto1: Automatically adjusts the picture for the best quality when watching a lm.

Auto2: Automatically optimizes the video text when watching a lm.

Cinema Smooth: Offers the ultimate cinema experience.

Film mode is supported in TV, Video, Component(480i / 1080i) and HDMI(1080i).

Real 100Hz Demo → Off / On

You can get a clear distinction between Real 100Hz and 50Hz, especially when watching fast moving scenes. Therefore, when

seeing slow moving scenes, you will not be able to distinguish between Real 100Hz and 50Hz. Demo 100Hz works only with 50Hz

signal. Real 100Hz demo mode is provided for shop demonstration with special pictures.

Blue Only Mode → Off / On

This function is for AV device measurement experts. This function displays the blue signal only by removing the red and green

signals from the video signal so as to provide a Blue Filter effect that is used to adjust the Colour and Tint of video equipment such

as DVD players, Home Theaters, etc.

Blue Only Mode is available when the picture mode is set to Movie or Standard.

Screen Burn Protection

To reduce the possibility of screen burn, this unit is equipped with screen burn prevention technology. This technology enables you

to set picture movement up/down (Vertical) and side to side (Horizontal). The Time setting allows you to program the time between

movement of the picture in minutes.

Pixel Shift: Using this function, you can minutely move pixels on the PDP in horizontal or vertical direction to minimize after

image on the screen.

Optimum condition for pixel shift

Item TV/Ext./AV/Component/HDMI/PC

Horizontal 0~2 2

Vertical 0~4 4

Time (minute) 1~4 min 2 min

The Pixel Shift value may differ depending on the monitor size (inches) and mode.

This function is not available in the Screen Fit mode.

Scrolling: This function helps remove after images on the screen by moving all the pixels on the PDP according to a pattern.

Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image

on the screen for a long time.

Side Grey: When you watch TV with the screen ratio of 4:3, the screen is prevented from any damage by adjusting the white

balance on both extreme left and right sides.

- Light: When you set the screen ratio to 4:3, it brightens the left and right sides.

- Dark: When you set the screen ratio to 4:3, it darkens the left and right sides.

Picture Reset →→ Reset Picture Mode / Cancel

Resets all picture settings to the default values.

Select a picture mode to be reset. The reset is performed for each picture mode.



N



•

N



N



•

N

•

❑

N

Picture

Advanced Settings

Picture Options

Picture Reset ►

Picture

BN68-02196D-00Eng.indb 19 2009-04-09 오후 4:21:08

English - 20

Setting up the TV with your PC

Preset: Press the SOURCE button to select PC mode.

Auto Adjustment

Auto Adjustment allows the PC screen of set to self-adjust to the incoming PC video

signal. The values of ne, coarse and position are adjusted automatically.

This function does not work in DVI-HDMI mode.

Press the TOOLS button to display Tools menu.

You can also set the auto adjustment by selecting Tools → Auto Adjustment.

T

Screen

The purpose of picture quality adjustment is to remove or reduce picture noise. If the

noise is not removed by Fine-tuning alone, then adjust the frequency as best as possible

(Coarse) and Fine-tune again. After the noise has been reduced, readjust the picture so

that it is aligned on the center of screen.

Coarse

Adjusts the frequency when vertical noise appears on the screen.

Fine

Adjusts the screen to be clearer.

PC Position

Adjust the PC’s screen positioning if it does not t the TV screen. Press the ▲ or ▼ button to adjusting the Vertical-Position.

Press the ◄ or ► button to adjust the Horizontal-Position.

Image Reset

You can replace all image settings with the factory default values.

N

❑

N

❑



Brightness : 45

Sharpness : 50

Auto Adjustment ►

Screen

Advanced Settings

Picture Options

Picture Reset

Picture

BN68-02196D-00Eng.indb 20 2009-04-09 오후 4:21:08

Страница загружается ...

Samsung PS58B850Y1W Руководство пользователя

Это руководство также подходит для

Samsung PS58B850Y1W Руководство пользователя

на других языках

Похожие модели бренда

Модели других брендов