Yamaha RX-V496 Руководство пользователя

Бренд: Yamaha

Модель: RX-V496

Категория: Ресиверы

Тип: Руководство пользователя

Это руководство также подходит для

HTR-5240

OWNER’S MANUAL

MODE D’EMPLOI

HTR-5240

Natural Sound AV Receiver

Ampli-tuner audio-vidéo

U C A

1/17/0, 3:57 PM

CAUTION

SAFETY INSTRUCTIONS

8 Ventilation – The unit should be situated so that its

location or position does not interfere with its proper

ventilation. For example, the unit should not be situated

on a bed, sofa, rug, or similar surface, that may block the

ventilation openings; or placed in a built-in installation,

such as a bookcase or cabinet that may impede the flow

of air through the ventilation openings.

9 Heat – The unit should be situated away from heat

sources such as radiators, stoves, or other appliances

that produce heat.

10 Power Sources – The unit should be connected to a

power supply only of the type described in the operating

instructions or as marked on the unit.

11 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the unit.

12 Cleaning – The unit should be cleaned only as

recommended by the manufacturer.

13 Nonuse Periods – The power cord of the unit should be

unplugged from the outlet when left unused for a long

period of time.

14 Object and Liquid Entry – Care should be taken so that

objects do not fall into and liquids are not spilled into the

inside of the unit.

15 Damage Requiring Service – The unit should be serviced

by qualified service personnel when:

A. The power-supply cord or the plug has been

damaged; or

B. Objects have fallen, or liquid has been spilled into the

unit; or

C. The unit has been exposed to rain; or

D. The unit does not appear to operate normally or exhibits

a marked change in performance; or

E. The unit has been dropped, or the cabinet damaged.

16 Servicing – The user should not attempt to service the

unit beyond those means described in the operating

instructions. All other servicing should be referred to

qualified service personnel.

17 Power Lines – An outdoor antenna should be located

away from power lines.

18 Grounding or Polarization – Precautions should be taken

so that the grounding or polarization is not defeated.

1 Read Instructions – All the safety and operating

instructions should be read before the unit is operated.

2 Retain Instructions – The safety and operating

instructions should be retained for future reference.

3 Heed Warnings – All warnings on the unit and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and other instructions

should be followed.

5 Water and Moisture – The unit should not be used near

water – for example, near a bathtub, washbowl, kitchen

sink, laundry tub, in a wet basement, or near a swimming

pool, etc.

6 Carts and Stands – The unit should be used only with a

cart or stand that is recommended by the

manufacturer.

6A A unit and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause

the unit and cart combination to overturn.

7 Wall or Ceiling Mounting – The unit should be mounted to

a wall or ceiling only as recommended by the

manufacturer.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

alert you to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert you to the presence

of important operating and maintenance

(servicing) instructions in the literature

accompanying the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO

RAIN OR MOISTURE.

0101V496caution_EN(UCA) 1/11/0, 10:48 AM2

CAUTION

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

19 For US customers only:

Outdoor Antenna Grounding – If an outside antenna is

connected to this unit, be sure the antenna system is

grounded so as to provide some protection against

voltage surges and built-up static charges. Article 810 of

the National Electrical Code, ANSI/NFPA 70, provides

information with regard to proper grounding of the mast

and supporting structure, grounding of the lead-in wire to

an antenna discharge unit, size of grounding conductors,

location of antenna discharge unit, connection to

grounding electrodes, and requirements for the

grounding electrode.

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC

– NATIONAL ELECTRICAL CODE

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s

Consumer Electronics Group want you to get the most out of

your equipment by playing it at a safe level. One that lets the

sound come through loud and clear without annoying blaring

or distortion – and, most importantly, without affecting your

sensitive hearing.

Since hearing damage from loud sounds is often

undetectable until it is too late, YAMAHA and the

Electronic Industries Association’s Consumer

Electronics Group recommend you to avoid

prolonged exposure from excessive volume

levels.

FCC INFORMATION (for US customers only)

1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC,

to use the product.

2. IMPORTANT : When connecting this product to

accessories and/or another product use only high

quality shielded cables. Cable/s supplied with this

product MUST be used. Follow all installation instruc-

tions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE : This product has been tested and found to

comply with the requirements listed in FCC Regula-

tions, Part 15 for Class “B” digital devices. Compliance

with these requirements provides a reasonable level of

assurance that your use of this product in a residential

environment will not result in harmful interference with

other electronic devices.

This equipment generates/uses radio frequencies and,

if not installed and used according to the instructions

found in the users manual, may cause interference

harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If

this product is found to be the source of interference,

which can be determined by turning the unit “OFF”

and “ON”, please try to eliminate the problem by using

one of the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch

(circuit breaker or fuse) circuits or install AC line filter/

In the case of radio or TV interference, relocate/

reorient the antenna. If the antenna lead-in is 300

ohm ribbon lead, change the lead-in to coaxial type

cable.

If these corrective measures do not produce satisfac-

tory results, please contact the local retailer autho-

rized to distribute this type of product. If you can not

locate the appropriate retailer, please contact Yamaha

Electronics Corp., U.S.A. 6660 Orangethorpe Ave,

Buena Park, CA 90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in particular,

specifies that the cable ground shall be connected to the

grounding system of the building, as close to the point of

cable entry as practical.

SAFETY INSTRUCTIONS

0101V496caution_EN(UCA) 1/11/0, 10:48 AM3

CAUTION

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

1. To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

2. Install this unit in a cool, dry, clean place — away

from windows, heat sources, sources of excessive

vibration, dust, moisture and cold. Avoid sources of

humming (transformers, motors). To prevent fire or

electrical shock, do not expose the unit to rain or

water.

3. Never open the cabinet. If something drops into the

unit, contact your dealer.

4. Do not use force on switches, controls or connection

wires. When moving the unit, first disconnect the

power cord and then the wires connected to other

component. Never pull the wires themselves.

5. The openings on the cover assure proper ventilation

of the unit. If these openings are obstructed, the

temperature inside the unit will rise rapidly.

Therefore, avoid placing objects against these

openings, and install the unit in a well-ventilated area

to prevent fire and damage.

6. The voltage used must be the same as that specified

on this unit. Using this unit with a higher voltage than

specified is dangerous and may result in fire or other

accidents. YAMAHA will not be held responsible for

any damage resulting from the use of this unit with a

voltage other than that specified.

7. Digital signals generated by this unit may interfere

with other component such as tuners, receivers and

TVs. Move this unit farther away from such

component if interference is observed.

8. Always set VOLUME to the “m” position before

starting the audio source play. Increase the volume

gradually to an appropriate level after playback has

been started.

9. Do not attempt to clean the unit with chemical

solvents; this might damage the finish. Use a clean,

dry cloth.

10. Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before

concluding that the unit is faulty.

11. When not planning to use this unit for a long period

of time (e.g., a vacation), disconnect the AC power

cord from the wall outlet.

12. To prevent lightning damage, disconnect the AC

power cord and disconnect the antenna cable when

there is an electrical storm.

13. Grounding or polarization — Precautions should be

taken so that the grounding or polarization of the unit

is not defeated.

14. AC outlet — Do not connect audio component to the

AC outlet on the rear panel if that component

requires more power than the outlet is rated to

provide.

This unit is not disconnected from the AC power source

as long as it is connected to the wall outlet, even if this

unit itself is turned off. This state is called the standby

mode. In this state, this unit is designed to consume a

very small quantity of power.

IMPORTANT

Please record the serial number of this unit in the space

below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

0101V496caution_EN(UCA) 1/11/0, 10:48 AM4

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

FEATURES

5-Channel Power Amplification

◆ Minimum RMS Output

(0.06% THD, 20 Hz – 20 kHz)

[U.S.A. and Canada models]

Main: 70 W + 70 W (8 Ω)

Center: 70 W (8 Ω)

Rear: 70 W + 70 W (8 Ω)

[Australia model]

Main: 65 W + 65 W (8 Ω)

Center: 65 W (8 Ω)

Rear: 65 W + 65 W (8 Ω)

Multi-mode Digital Sound Field

Processing

◆ Digital Sound Field Processor (DSP)

◆ Dolby Digital Decoder

◆ Dolby Pro Logic Decoder

◆ DTS Decoder

◆ CINEMA DSP: Theater-like Sound Experience by

the Combination of YAMAHA DSP Technology

and Dolby Digital, Dolby Pro Logic or DTS

◆ Automatic Input Balance Control for Dolby Pro

Logic decoding

Sophisticated FM/AM Tuner

◆ 40-Station Random Access Preset Tuning

◆ Automatic Preset Tuning

◆ Preset Station Shifting Capability (Preset Editing)

Other Features

◆ “SET MENU” which Provides You with 11 Items

for Optimizing This Unit for Your Audio/Video

System

◆ Test Tone Generator for Easier Speaker Balance

Adjustment

◆ 6-Channel External Decoder Input for Other Future

Formats

◆ Video Signal Input/Output Capability

(Including S Video Connections)

◆ 2 Optical/1 Coaxial Digital Signal Input Terminals

◆ SLEEP Timer

◆ Remote Control with Preset Manufacturer Codes

INTRODUCTION

CONTENTS

PREPARATION

SPEAKER SETUP....................................................... 8

CONNECTIONS.......................................................... 9

ADJUSTING THE SPEAKER BALANCE ............ 18

BASIC OPERATION

PLAYING A SOURCE .............................................. 20

DIGITAL SOUND FIELD PROCESSOR (DSP)

EFFECT .................................................................. 24

SOUND FIELD PROGRAM .................................... 25

TUNING ..................................................................... 28

RECORDING A SOURCE ON TAPE, MD OR

VIDEO CASSETTE ............................................... 32

ADVANCED OPERATION

SET MENU................................................................. 33

DELAY TIME AND SPEAKER

OUTPUT LEVELS ................................................. 37

SLEEP TIMER .......................................................... 39

PRESET REMOTE CONTROL .............................. 40

APPENDIX

TROUBLESHOOTING ............................................ 47

SPECIFICATIONS.................................................... 50

GLOSSARY................................................................ 52

INDEX ........................................................................ 53

INTRODUCTION

FEATURES .................................................................. 1

CONTENTS ................................................................. 1

GETTING STARTED ................................................. 2

CONTROLS AND FUNCTIONS ............................... 4

y indicates a tip for your operation.

Manufactured under license from Digital Theater Systems, Inc.

US Pat. No. 5,451,942 and other world-wide patents issued and

pending. “DTS”, “DTS Digital Surround”, are trademarks of

Manufactured under license from Dolby

Laboratories. “Dolby”, “Pro Logic” and the

double-D symbol are trademarks of Dolby

Laboratories. Confidential Unpublished Works.

rights reserved.

0102V49601-07_EN(UCA) 1/11/0, 11:20 AM1

GETTING STARTED

Checking the Package Contents

Check that the following items are included in your package.

Remote control Batteries (AAA, R03, UM-4 type) Antenna adapter

(U.S.A. and Canada models only)

Indoor FM antenna Quick reference card

Connection guide

Battery Installation in the Remote

Control

1 Turn the remote control over and slide the

battery compartment cover in the direction of

the arrow.

2 Insert the batteries (AAA, R03 or UM-4 type)

according the polarity markings on the inside

of the battery compartment.

3 Close the battery compartment cover.

Battery Replacement

If the remote control operates only when it is close to the

unit, the batteries are weak. Replace all the batteries with

new ones.

Be sure to replace the batteries within about two minutes.

If it takes longer than two minutes, the codes preset for

the remote control will return to the factory settings.

(Refer to pages 40 to 46 about the remote control.)

Notes

• Use only AAA, R03 or UM-4 batteries for replacement.

• Be sure the battery polarity is correct. (See the illustration inside

the battery compartment.)

• Remove the batteries if the remote control will not be used for an

extended period of time.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

AM loop antenna

0102V49601-07_EN(UCA) 1/12/0, 4:11 PM2

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

Using the Remote Control

The remote control transmits a directional infrared beam. Be

sure to aim the remote control directly at the infrared sensor

during operation. When the sensor is covered or there is a

large object between the remote control and the sensor, the

sensor cannot receive signals. The sensor may not be able to

receive signals properly when it is exposed to direct sunlight

or a strong artificial light (such as a fluorescent or strobe

light). In this case, change the direction of the light or

reposition the unit to avoid direct lighting.

Notes

• Handle the remote control with care.

• Do not spill water, tea or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following

conditions:

– high humidity or temperature such as near a heater, stove or

bath;

– dusty places; or

– extremely low temperature.

GETTING STARTED

Remote control

sensor

Within approximately 6 m

(20 feet)

0102V49601-07_EN(UCA) 1/12/0, 4:11 PM3

–

12 3 4 65

7890qwerty

u i op

6 VOLUME

Turn this control to turn up or down the volume.

7 PHONES jack

Connect the headphones to the PHONES jack. You can

listen to the sound to be output from the main speakers

through the headphones.

When using headphones only, set both SPEAKERS A and B

to the OFF position and press EFFECT to turn off the effect

speakers (center and rear) (so that no DSP program name

appear on the display).

8 SPEAKERS

Set A or B (or both A and B) to the ON position for the main

speaker system (connected to this unit) that you want to use.

Set the button(s) to the OFF position for the main speaker

system that you don’t want to use.

9 PROGRAM selector

Press l or h to select a DSP program when the effect

speakers (center and rear) are turned on. The name of the

selected program appears on the display.

0 EFFECT

Press this button to turn on or off the effect speakers (center

and rear). If you turn them off, all Dolby Digital and DTS

audio signals are directed to the right and left main

speakers. In that case, the output levels of the right and left

speakers may not match.

CONTROLS AND FUNCTIONS

Front Panel

1 STANDBY/ON

Press this switch to turn on the power of this unit or to set

this unit in the standby mode. Before turning the power on,

set VOLUME to the “m” position.

Standby mode

In this mode, this unit consumes a very small quantity of

power to receive infrared-signals from the remote

control.

2 Remote control sensor

This receives signals from the remote control.

3 Display

This shows various information. (Refer to page 6 for

details.)

4 INPUT MODE

Press this button to select the input mode among AUTO,

DTS and ANALOG for the DVD/LD, TV/digital TV and

satellite tuner sources.

5 INPUT SELECTOR

Turn this selector to select the input source (TUNER, CD,

PHONO, V-AUX, VCR, SAT/D-TV, DVD/LD) that you

want to listen to or watch. The arrow for the selected input

source indicator lights up on the display.

0102V49601-07_EN(UCA) 1/20/0, 10:50 AM4

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

q Tone controls

These controls are only effective for the sound from the

main speakers.

a) BASS

Turn this control clockwise to increase or counterclockwise

to decrease the low-frequency response. The “0” position

produces a flat response.

b) TREBLE

Turn this control clockwise to increase or counterclockwise

to decrease the high-frequency response. The “0” position

produces a flat response.

w TAPE/MD MON / EXT. DECODER

Press this button to select a tape or an MD source. The

“TAPE/MD MONITOR” indicator lights up on the display.

When you press the button next, the “TAPE/MD

MONITOR” indicator goes off, “EXT. DECODER” appears

on the display and you can listen to a source connected to

the EXTERNAL DECODER INPUT terminals.

e BALANCE

This control is only effective for the sound from the main

speakers.

Turn the control to adjust the balance of the output volume

from the right and left main speakers to compensate for

sound imbalance caused by the speaker location or listening

room conditions.

r A/B/C/D/E

Press this button to select one of a group (A to E) of preset

stations.

t PRESET/TUNING

When “ z ” appears

This button is used to select a preset station number (1 to 8).

Press h to select a higher and l to select a lower preset

station number.

When “ z ” goes off

This button is used for tuning. Press h to tune in to higher

frequencies, and l to tune in to lower frequencies.

y PRESET/TUNING, EDIT

Press this button to turn on or off “ z ” on the display and

switch the function between for storing a broadcasting

station (preset tuning) and for tuning. This button is also

used to exchange the assignment of two preset stations with

each other.

u FM/AM

Press this button to switch the reception band between FM

and AM.

i MEMORY (MAN’L/AUTO FM)

Press this button to store the broadcasting stations. Hold

down this button for more than three seconds to begin

automatic preset tuning.

o TUNING MODE (AUTO/MAN’L MONO)

Press this button to switch the tuning mode between

automatic and manual. To use the automatic tuning method,

press this button so that the “AUTO” indicator lights up on

the display. To use the manual tuning method, press this

button so that the “AUTO” indicator goes off.

p VIDEO AUX terminals

Connect an auxiliary audio or video input source such as a

camcorder to these terminals. Use INPUT SELECTOR to

select the source connected to these terminals.

CONTROLS AND FUNCTIONS

0102V49601-07_EN(UCA) 1/12/0, 4:11 PM5

Display

6 g and o indicators

“ g ” lights up when the built-in Dolby Digital

decoder is on and the signals of the selected source are

encoded with Dolby Digital. “ o ” lights up when

the built-in Dolby Pro Logic decoder is on.

7 x indicator

“ x ” lights up when the built-in digital sound

field processor is on.

8 MEMORY indicator

This flashes for about five seconds after pressing

MEMORY. During this period, the displayed station can be

stored in the memory.

9 AUTO indicator

This lights up when the unit is in the automatic tuning

mode.

0 STEREO indicator

This lights up when an FM stereo broadcast with sufficient

signal strength is being received.

q Signal-level indicator

This indicates the signal level of the station being received.

If multipath interference is detected, the indication

decreases.

w SLEEP indicator

This lights up while the built-in SLEEP timer is on.

CONTROLS AND FUNCTIONS

1 t indicator

The “t” indicator lights up when the built-in DTS

decoder is turned on.

2 DSP program indicators

The name of the selected DSP program lights up in the

following cases:

• When the tuner is selected as the input source.

• When DSP program No. 2, 3 or the subprogram

“ENHANCED” of No.1 is selected.

3 Multi-information display

This display shows various information: for example the

name of the selected DSP program and the various settings

during adjustment with the SET MENU. The current station

frequency and band (FM or AM) also appear when the tuner

is selected as the input source.

4 Input source indicators

One of the arrows for these indicators lights up depending

on which source is selected.

5 TAPE/MD MONITOR indicator

This lights up when the tape deck or MD recorder, etc. is

selected as the input source by pressing TAPE/MD MON /

EXT. DECODER (or TAPE/MD).

0102V49601-07_EN(UCA) 2/10/0, 11:20 AM6

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION PREPARATION

Remote Control

1 Indicator

This flashes in red when pressing a button on the remote

control. If it flashes rapidly several times, press the selected

button again.

2 Component selector buttons

Press one of these buttons which corresponds to the

component you want to control with the remote control.

(The proper code must be set for your component. Refer to

“Setup codes” on page 45.) When the component selector

button has been pressed, the remote control is set to that

component operation mode.

3 POWER

Each time you press this button, the unit switches between

the power on and standby mode.

4 TEST

Press this button to output the test tone for each speaker.

5 A/B/C/D/E, PRESET +/–

These buttons are used to select a preset station.

A/B/C/D/E: To select one of a group (A to E) of preset

stations

PRESET +/–: To select a preset station number (1 to 8)

6 MUTE

Press this button to mute the sound. To cancel mute, press

this button again.

7 VOLUME

These buttons are used to adjust the volume level.

u: To turn up the volume

d: To turn down the volume

8 SLEEP

Press this button to set the SLEEP timer.

9 +/–

These buttons adjust the settings of the SET MENU and

TIME/LEVEL mode.

0 TIME/LEVEL

Press this button to select the items in the TIME/LEVEL

mode.

q Input selector buttons

These buttons select the input source.

CD: To play a CD

TUNER: To listen to an FM or AM broadcast

TAPE/MD: To play a tape or MD

DVD/LD: To play a DVD or LD

SAT/D-TV: To watch a TV or satellite broadcast

VCR: To play a video cassette

PHONO: To play an analog record

V-AUX: To use a camcorder

EXT. DEC.: To play other multi-channel source

w EFFECT

Press this button to turn on or off the effect speakers (center

and rear).

e PRG+, PRG–

Press these buttons to select a DSP program.

r SET MENU

Press this button to select the items in the SET MENU.

CONTROLS AND FUNCTIONS

TV VOLUME

TV INPUT

Press AMP(TUNER).

This section describes basic operation of this unit with the

remote control. First, press AMP(TUNER) on the

component selector. Refer to “PRESET REMOTE

CONTROL” on page 40 for full details.

0102V49601-07_EN(UCA) 1/20/0, 10:50 AM7

SPEAKER SETUP

Speaker Placement

Refer to the following diagram when you place the

speakers.

Speakers to Be Used

This unit is designed to provide the best sound-field quality

with a 5-speaker system, using main speakers, rear speakers

and a center speaker. If you use different brands of speakers

(with different tonal qualities) in your system, the tone of a

moving human voice and other types of sound may not shift

smoothly. We recommend that you use speakers from the

same manufacture or speakers with the same tonal quality.

The main speakers are used for the main source sound plus

the effect sounds. They will probably be the speakers from

your present stereo system. The rear speakers are used for

the effect and surround sounds, and the center speaker is for

the center sounds (dialog, vocals, etc.). If for some reason it

is not practical to use a center speaker, you can do without

it. Best results, however, are obtained with the full system.

The main speakers should be high-performance models and

have enough power-handling capacity to accept the

maximum output of your audio system. The other speakers

do not have to be equal to the main speakers. For precise

sound localization, however, it is ideal to use high-

performance models that can reproduce sounds over the full

range for the center speaker and the rear speakers.

■ Use of a subwoofer expands your

sound field

It is also possible to further expand your system with the

addition of a subwoofer. The use of a subwoofer is effective

not only for reinforcing bass frequencies from any or all

channels, but also for reproducing the LFE (low frequency

effect) channel with high fidelity when playing back a

source encoded with Dolby Digital or DTS. The YAMAHA

Active Servo Processing Subwoofer System is ideal for

natural and lively bass reproduction.

Main

speaker (L)

Center speaker

Main speaker (R)

Subwoofer

Rear speaker (L)

Rear speaker (R)

1.8 m

■ Main speakers

Place the right and left main speakers an equal distance

from the ideal listening position. The distance of each

speaker from each side of the TV monitor should be the

same.

■ Rear speakers

Place these speakers behind your listening position, facing

slightly inwards, nearly 1.8 m (approx. 6 feet) above the

floor.

■ Center speaker

Align the front face of the center speaker with the front face

of your TV monitor. Place the speaker as close to the

monitor as possible, such as directly over or under the

monitor and centrally between the main speakers.

Note

• If the center speaker is not used, the sound will be heard from the

right and left main speakers. In that case, “CENTER SP” in the

SET MENU is set to the NONE position. (Refer to page 34 for

details.)

■ Subwoofer

The position of the subwoofer is not so critical, because low

bass sounds are not highly directional. But it is better to

place the subwoofer near the main speakers. Turn it slightly

toward the center of the room to reduce the wall reflections.

CAUTION

Some types of speakers interfere with a TV monitor. If

this problem occurs, move the speakers away from the

monitor. If you cannot avoid installing the center speaker

or subwoofer near the TV monitor, use magnetically

shielded speakers.

PREPARATION

0103V49608-19_EN(UCA) 1/11/0, 11:24 AM8

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

CONNECTIONS

Before Connecting Components

CAUTION

Never connect this unit and other components to mains power until all connections between components have been

completed.

Be sure all connections are made correctly, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Some

components require different connection methods and have different terminal names. Refer to the instructions for each

component to be connected to this unit.

When you connect other YAMAHA audio components (such as a tape deck, MD recorder and CD player or changer), connect

it to the terminals with the same number labels as !, #, $ etc. YAMAHA applies this labeling system to all its products.

Use RCA-type pin plug cables for connecting audio/video components with the exception described later.

The input and output terminals for pin plugs can be distinguished as follows:

Yellow video signals (composite)

White analog audio signals for the left channel

Red analog audio signals for the right channel

coaxial digital signals

After completing all connections, check them again to make sure they are correct.

MAINS

120 V 60Hz

100W MAX. TOTAL

SWITCHED

MAIN A OR B

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

CENTER : 6ΩMIN. /SPEAKER

REAR : 6ΩMIN. /SPEAKER

MAIN A OR B

8ΩMIN. /SPEAKER

I6ΩMIN. /SPEAKER

CENTER : 8ΩMIN. /SPEAKER

REAR : 8ΩMIN. /SPEAKER

SET BEFORE POWER ON

REAR

(SURROUND)

CENTER

MAIN

––++

–

Connecting an Audio

Component (page 12)

Connecting a Video

Component (page 13)

IMPEDANCE SELECTOR

switch (page 17)

Connecting the

Antenna (page 10)

Connecting to an External

Decoder (page 14)

Connecting Speakers

(page 15)

Connecting the Power

Supply Cords (page 17)

(U.S.A. model)

V V

C C

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM9

Connecting the Antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal

strength. However, a properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor

reception quality, an outdoor antenna may improve the quality.

Connect each antenna correctly to the designated terminals.

■ Indoor FM antenna (included)

Firmly insert the connector into the FM ANT terminal. The

indoor FM antenna is only a simple antenna. For reception

with better sound quality, installing the outdoor FM antenna

(commercially available) is recommended.

Note

• Do not connect an outdoor FM antenna and the indoor FM

antenna at the same time.

■ Outdoor FM antenna

You may be unable to obtain good FM radio reception

depending on your local conditions (distance from the

broadcasting station, interposing buildings and

mountains, etc.). Consult your dealer or authorized service

center and be sure to install an antenna that suits your local

conditions.

Install the outdoor FM antenna (commercially available) in

a high place as far away from any roads as possible to avoid

being affected by automobile ignition noise.

CONNECTIONS

Indoor FM

antenna

Antenna adapter (included

for U.S.A. and Canada

models)

Note

Use this adapter to match with

F-type connector.

75-ohm coaxial cable

75-ohm/300-ohm antenna

adapter

300-ohm feeder

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM10

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

■ AM loop antenna (included)

The AM loop antenna can be removed from the stand and

attached to a wall, etc. However, note that the reception

sensitivity may deteriorate if the antenna is attached to a

metal or steel reinforced wall.

Notes

• The AM loop antenna should be placed away from this unit.

• The AM loop antenna should always be connected, even if an

outdoor AM antenna is connected to this unit.

■ Connecting the AM loop antenna

1 Press the tab and unlock the terminal hole.

2 Insert the AM loop antenna lead wires into the

AM ANT and GND terminals.

3 Return the tab to its original position to lock

the lead wires. Lightly pull the lead wires to

confirm a good connection.

4 Attach the loop antenna to the antenna stand.

5 Orient the AM loop antenna so that the best

reception is obtained.

■ Outdoor AM antenna

If you cannot obtain good reception with the AM loop

antenna, connect 5 m to 10 m of vinyl covered wire to the

AM ANT terminal and extend it outdoors from a window.

■ Ground (GND terminal)

For maximum safety and minimum interference, connect

the antenna GND terminal to a good earth ground. A good

earth ground is a metal stake driven into moist earth.

CONNECTIONS

Antenna stand

AM loop antenna

Vinyl covered wire (5 m to 10 m)

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM11

Connecting an Audio Component

■ PHONO terminals

These terminals are used to connect a turntable with an MM

or high-output MC cartridge. If you have a turntable with a

low-output MC cartridge, use an inline boosting transformer

or MC head amplifier when connecting to these terminals.

Connecting the ground (earth) wire of the turntable to the GND

terminal will normally minimize hum, but in some cases, better

results may be obtained with the ground wire disconnected.

CONNECTIONS

Be sure to connect the right channel (R), left channel (L),

input (IN) and output (OUT) properly.

Tape deck or

MD recorder

L R

L R L R

OUTPUT

OUTPUT LINE OUT LINE IN

GND

Turntable

(U.S.A. model)

CD player

Analog signal

Signal flow

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM12

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

Connecting a Video Component

■ Audio signal terminals

Be sure to connect the right channel (R), left channel (L),

input (IN) and output (OUT) properly.

■ Video signal terminals

Be sure to connect the input (IN) and output (OUT)

properly.

■ Digital audio signal terminals

If your DVD/LD player, TV/digital TV or satellite

tuner, etc. has coaxial or optical digital signal output

terminals, they can be connected to this unit’s COAXIAL

and/or OPTICAL digital signal input terminals. To make a

connection between the optical digital signal terminals,

remove the cover from each terminal, and then connect

them by using a commercially available optical fiber cable

that conforms to EIA standards. Other cables might not

function correctly.

When making connections between the digital signal

terminals, you should connect the components to the same-

named analog audio signal terminals of this unit, because a

digital signal cannot be recorded by a tape deck, MD

recorder or VCR connected to this unit.

Notes

• Be sure to attach the covers when the OPTICAL terminals are not

being used in order to protect them from dust.

• If your LD player has a Dolby Digital RF signal output terminal,

be sure to use the RF demodulator (separately purchased).

• No sound will be heard when connecting your LD player’s Dolby

Digital RF signal output terminal directly to this unit’s COAXIAL

DVD/LD digital signal input terminal.

• The input signal from the DVD/LD input terminals is selected in

the following order of priority with the input mode set to AUTO:

COAXIAL terminal → OPTICAL terminal → Analog terminal.

Refer to page 22 for details.

• All digital signal input terminals are applicable to sampling

frequencies of 32 kHz, 44.1 kHz and 48 kHz.

CONNECTIONS

L R

L R V V

ANALOG

AUDIO OUT

AUDIO

OUT

AUDIO

VIDEO

OUT

VIDEO

ANALOG

AUDIO OUT

VIDEO

OUT

VIDEO

OUT

COAXIAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

OPTICAL

DIGITAL OUT

DVD/LD player TV/digital TV, satellite tuner, cable TV

(U.S.A. model)

VCR

Analog signal

Video signal

Digital signal

(optical)

Digital signal

(coaxial)

Signal flow

TV monitor

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM13

■ S VIDEO terminals

If your VCR, TV monitor or DVD/LD player has “S” (high-

resolution) video terminals, they can be connected to this

unit’s S VIDEO terminals. Connect the VCR’s “S” video

input and output terminals to this unit’s S VIDEO VCR

OUT and IN terminals, respectively. Connect the monitor’s

“S” video input terminal to this unit’s S VIDEO MONITOR

OUT terminal. Connect the DVD/LD player’s “S” video

output terminal to this unit’s S VIDEO DVD/LD terminal.

Otherwise, connect the composite video terminals of your

VCR, TV monitor or DVD/LD player to this unit’s

composite video terminals.

Notes

• Use a special S VIDEO cable (commercially available) for the S

VIDEO connection.

• If video signals are input from both the S VIDEO input and

composite input terminals, the signals will be directed to their

respective output terminals.

■ VIDEO AUX terminals (on the front panel)

These terminals are used to connect any video input source

such as a camcorder to this unit.

Connecting to an External Decoder

This unit has additional 6-channel audio signal input

terminals for connecting an external decoder to this unit.

Connect the 6-channel audio signal output terminals of the

decoder to the EXTERNAL DECODER INPUT terminals

of this unit.

Notes

• When a source connected to these terminals is selected, the digital

sound field processor cannot be used.

• The settings of “CENTER SP”, “REAR SP”, “MAIN SP” and

“BASS OUT” in the SET MENU have no effect on a source

connected to these terminals. The setting of “MAIN LVL” is

effective. (Refer to pages 34 and 35 for details.)

CONNECTIONS

L RV

AUDIO OUT R

AUDIO OUT L

VIDEO OUT

Camcorder

S VIDEO OUT

S VIDEO

OUT

S VIDEO IN

DVD/LD player

TV Monitor

VCR

S Video signal

Signal flow

L R L R

MAIN

OUT

SURROUND

OUT

CENTER

OUT

SUBWOOFER

OUT

External decoder

(U.S.A. model)

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM14

EnglishBASIC OPERATION

ADVANCED OPERA

TION APPENDIX

INTRODUCTION

PREPARATION

Connecting Speakers

Be sure to connect the right channel (R), left channel (L),

“+” (red) and “–” (black) properly. If the connections are

faulty, no sound will be heard from the speakers, and if the

polarity of the speaker connections is incorrect, the sound

will be unnatural and lack bass.

CAUTIONS

• Use speakers with the specified impedance shown on

the rear panel of this unit.

• Do not let the bare speaker wires touch each other and

do not let them touch any metal part of this unit. This

could damage the unit and/or speakers.

■ Main speaker terminals

One or two speaker systems can be connected to these

terminals. If you use only one speaker system, connect it to

either of the SPEAKERS A or B terminals.

■ Rear speaker terminals

A rear speaker system can be connected to these terminals.

■ Center speaker terminal

A center speaker can be connected to this terminal.

CONNECTIONS

MAINS

MAIN A OR B

4ΩMIN. /SPEAKER

8ΩMIN. /SPEAKER

CENTER : 6ΩMIN. /SPEAKER

REAR : 6ΩMIN. /SPEAKER

MAIN A OR B

8ΩMIN. /SPEAKER

I6ΩMIN. /SPEAKER

CENTER : 8ΩMIN. /SPEAKER

REAR : 8ΩMIN. /SPEAKER

SET BEFORE POWER ON

REAR

(SURROUND)

CENTER

MAIN

––++

–

120 V 60Hz

100W MAX. TOTAL

SWITCHED

Main speakers A

Right Left

Main speakers B

Right Left

(U.S.A. model)

Center speaker Rear speakers

Right Left

Subwoofer connection

If you have a subwoofer with built-

in amplifier, including the

YAMAHA Active Servo Processing

Subwoofer System, connect the

input terminal of the subwoofer

system to the SUBWOOFER

OUTPUT terminal of this unit.

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM15

■ Speaker cables

1 Remove approx. 10 mm (3/8”) of insulation

from each of the speaker cable.

2 Twist the exposed wires of the cable together

to prevent short circuits.

■ Connecting to the MAIN SPEAKERS terminals

1 Unscrew the knob.

2 Insert one bare wire into the hole in the side of

each terminal.

3 Tighten the knob to secure the wire.

■ Connecting to the REAR and CENTER SPEAKERS terminals

1 Open the tab.

2 Insert one bare wire into the hole of each

terminal.

3 Return the tab to secure the wire.

Banana plug connections are also possible. Simply insert the

banana plug connector into the corresponding terminal.

CONNECTIONS

10 mm (3/8”)

Red: positive (+)

Black: negative (–)

Red: positive (+)

Black: negative (–)

0103V49608-19_EN(UCA) 1/11/0, 11:25 AM16

Страница загружается ...

Yamaha RX-V496 Руководство пользователя

Бренд: Yamaha

Модель: RX-V496

Категория: Ресиверы

Тип: Руководство пользователя

Это руководство также подходит для

HTR-5240

Скачать PDF

сообщить о нарушении

на других языках

English: Yamaha RX-V496 User manual
français: Yamaha RX-V496 Manuel utilisateur
italiano: Yamaha RX-V496 Manuale utente
español: Yamaha RX-V496 Manual de usuario
Deutsch: Yamaha RX-V496 Benutzerhandbuch
Nederlands: Yamaha RX-V496 Handleiding
português: Yamaha RX-V496 Manual do usuário
dansk: Yamaha RX-V496 Brugermanual
polski: Yamaha RX-V496 Instrukcja obsługi
čeština: Yamaha RX-V496 Uživatelský manuál
svenska: Yamaha RX-V496 Användarmanual
Türkçe: Yamaha RX-V496 Kullanım kılavuzu
suomi: Yamaha RX-V496 Ohjekirja
română: Yamaha RX-V496 Manual de utilizare

Модели других брендов

Raven Slingshot Инструкция по установке

Yamaha RX-V496 Руководство пользователя

Это руководство также подходит для

Yamaha RX-V496 Руководство пользователя

на других языках

Похожие модели бренда

Модели других брендов