Yamaha RX V663 - AV Receiver Инструкция по применению

YAMAHA ELECTRONICS CORPORATION, USA

6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.

YAMAHA CANADA MUSIC LTD.

135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA

YAMAHA ELECTRONIK EUROPA G.m.b.H.

SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY

YAMAHA ELECTRONIQUE FRANCE S.A.

RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE

YAMAHA ELECTRONICS (UK) LTD.

YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND

YAMAHA SCANDINAVIA A.B.

J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN

YAMAHA MUSIC AUSTRALIA PTY, LTD.

17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

©

RX-V663

Printed in Malaysia WN24900

RX-V663

AV Receiver

OWNER’S MANUAL

U

RX-V663_U-cv.fm Page 1 Sunday, December 2, 2007 8:23 PM

Black process 45.0° 240.0 LPI

IMPORTANT SAFETY INSTRUCTIONS

Caution-i En

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert you to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle

is intended to alert you to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

1 Read Instructions – All the safety and operating instructions

should be read before the product is operated.

2 Retain Instructions – The safety and operating instructions

should be retained for future reference.

3 Heed Warnings – All warnings on the product and in the

operating instructions should be adhered to.

4 Follow Instructions – All operating and use instructions

should be followed.

5 Cleaning – Unplug this product from the wall outlet before

cleaning. Do not use liquid cleaners or aerosol cleaners.

6 Attachments – Do not use attachments not recommended by

the product manufacturer as they may cause hazards.

7 Water and Moisture – Do not use this product near water –

for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub; in a wet basement; or near a swimming pool;

and the like.

8 Accessories – Do not place this product on an unstable cart,

stand, tripod, bracket, or table. The product may fall,

causing serious injury to a child or adult, and serious

damage to the product. Use only with a cart, stand, tripod,

bracket, or table recommended by the manufacturer, or sold

with the product. Any mounting of the product should

follow the manufacturer’s instructions, and should use a

mounting accessory recommended by the manufacturer.

9 A product and cart combination should be moved with care.

Quick stops, excessive force, and uneven surfaces may

cause the product and cart combination to

overturn.

10 Ventilation – Slots and openings in the cabinet are provided

for ventilation and to ensure reliable operation of the

product and to protect it from overheating, and these

openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed,

sofa, rug, or other similar surface. This product should not

be placed in a built-in installation such as a bookcase or rack

unless proper ventilation is provided or the manufacturer’s

instructions have been adhered to.

11 Power Sources – This product should be operated only from

the type of power source indicated on the marking label. If

you are not sure of the type of power supply to your home,

consult your product dealer or local power company. For

products intended to operate from battery power, or other

sources, refer to the operating instructions.

12 Grounding or Polarization – This product may be equipped

with a polarized alternating current line plug (a plug having

one blade wider than the other). This plug will fit into the

power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to fit, contact

your electrician to replace your obsolete outlet. Do not

defeat the safety purpose of the polarized plug.

13 Power-Cord Protection – Power-supply cords should be

routed so that they are not likely to be walked on or pinched

by items placed upon or against them, paying particular

attention to cords at plugs, convenience receptacles, and the

point where they exit from the product.

14 Lightning – For added protection for this product during a

lightning storm, or when it is left unattended and unused for

long periods of time, unplug it from the wall outlet and

disconnect the antenna or cable system. This will prevent

damage to the product due to lightning and power-line

surges.

15 Power Lines – An outside antenna system should not be

located in the vicinity of overhead power lines or other

electric light or power circuits, or where it can fall into such

power lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from touching

such power lines or circuits as contact with them might be

fatal.

16 Overloading – Do not overload wall outlets, extension

cords, or integral convenience receptacles as this can result

in a risk of fire or electric shock.

17 Object and Liquid Entry – Never push objects of any kind

into this product through openings as they may touch

dangerous voltage points or short-out parts that could result

in a fire or electric shock. Never spill liquid of any kind on

the product.

18 Servicing – Do not attempt to service this product yourself

as opening or removing covers may expose you to

dangerous voltage or other hazards. Refer all servicing to

qualified service personnel.

19 Damage Requiring Service – Unplug this product from the

wall outlet and refer servicing to qualified service personnel

under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into the

product,

c) If the product has been exposed to rain or water,

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT SAFETY INSTRUCTIONS

Caution-ii En

EXAMPLE OF ANTENNA GROUNDING

MAST

GROUND

CLAMP

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810–20)

GROUNDING CONDUCTORS

(NEC SECTION 810–21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250. PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC – NATIONAL ELECTRICAL CODE

d) If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions as an

improper adjustment of other controls may result in

damage and will often require extensive work by a

qualified technician to restore the product to its normal

operation,

e) If the product has been dropped or damaged in any

way, and

f) When the product exhibits a distinct change in perfor-

mance - this indicates a need for service.

20 Replacement Parts – When replacement parts are required,

be sure the service technician has used replacement parts

specified by the manufacturer or have the same

characteristics as the original part. Unauthorized

substitutions may result in fire, electric shock, or other

hazards.

21 Safety Check – Upon completion of any service or repairs to

this product, ask the service technician to perform safety

checks to determine that the product is in proper operating

condition.

22 Wall or Ceiling Mounting – The unit should be mounted

to a wall or ceiling only as recommended by the

manufacturer.

23 Heat – The product should be situated away from heat

sources such as radiators, heat registers, stoves, or other

products (including amplifiers) that produce heat.

24 Outdoor Antenna Grounding – If an outside antenna or

cable system is connected to the product, be sure the antenna

or cable system is grounded so as to provide some

protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code, ANSI/NFPA 70,

provides information with regard to proper grounding of the

mast and supporting structure, grounding of the lead-in wire

to an antenna discharge unit, size of grounding conductors,

location of antenna discharge unit, connection to grounding

electrodes, and requirements for the grounding electrode.

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be

connected to the grounding system of the building, as

close to the point of cable entry as practical.

FCC INFORMATION (for US customers)

1 IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the

instructions contained in this manual, meets FCC

requirements. Modifications not expressly approved by

Yamaha may void your authority, granted by the FCC, to

use the product.

2 IMPORTANT: When connecting this product to

accessories and/or another product use only high quality

shielded cables. Cable/s supplied with this product MUST

be used. Follow all installation instructions. Failure to

follow instructions could void your FCC authorization to

use this product in the USA.

3 NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15

for Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance that

your use of this product in a residential environment will

not result in harmful interference with other electronic

devices.

This equipment generates/uses radio frequencies and, if

not installed and used according to the instructions found

in the users manual, may cause interference harmful to the

operation of other electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this

product is found to be the source of interference, which

can be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of the

following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Electronics

Corp., U.S.A. 6660 Orangethorpe Ave., Buena Park, CA

90620.

The above statements apply ONLY to those products

distributed by Yamaha Corporation of America or its

subsidiaries.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

Caution-iii En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at least

30 cm on the top, 20 cm on the left and right, and 20 cm on

the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– other components, as they may cause damage and/or

discoloration on the surface of this unit.

– burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

18 Before moving this unit, press

L

SYSTEM OFF to set this

unit to the standby mode, and then disconnect the AC power

plug from the AC wall outlet.

19 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC wall outlet. Voltages are:

Asia model ............................ 220/230–240 V AC, 50/60 Hz

General model ........ 110/120/220/230–240 V AC, 50/60 Hz

20 The batteries shall not be exposed to excessive heat such as

sunshine, fire or like.

21 Excessive sound pressure from earphones and headphones can

cause hearing loss.

Caution: Read this before operating your unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

As long as this unit is connected to the AC wall outlet,

it is not disconnected from the AC power source even

if you turn off this unit by

L

SYSTEM OFF. In this

state, this unit is designed to consume a very small

quantity of power.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

POUR LES CONSOMMATEURS CANADIENS

Pour éviter les chocs électriques, introduire la lame la

plus large de la fiche dans la borne correspondante de

la prise et pousser jusqu’au fond.

Cet appareil numérique de la classe B est conforme à

la norme NMB-003 du Canada.

IMPORTANT

Please record the serial number of this unit in the space

below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

1 En

PREPARATIONINTRODUCTION

BASIC

OPERATION

ADVANCED

OPERATION

ADDITIONAL

INFORMATION

APPENDIX

English

Features ................................................................... 2

Supplied accessories .................................................. 2

Notice ....................................................................... 3

Getting started ........................................................ 4

Quick start guide .................................................... 5

Connections ........................................................... 10

Optimizing the speaker setting for your listening

room (YPAO) .................................................... 32

Using AUTO SETUP .............................................. 32

Selecting the SCENE templates........................... 37

Selecting the desired SCENE template to the SCENE

buttons ................................................................. 37

Creating your original SCENE templates................ 40

Using the remote control for the SCENE feature .... 41

Playback ................................................................ 42

Basic procedure ....................................................... 42

Selecting the MULTI CH INPUT component......... 43

Selecting the front speaker set ................................. 43

Selecting audio input jacks (AUDIO SELECT)...... 44

Displaying the current status of this unit on a video

monitor ................................................................ 44

Using your headphones............................................ 45

Muting the audio output........................................... 45

Playing video sources

in the background of an audio source.................. 45

Displaying the input source information ................. 46

Using the sleep timer ............................................... 47

Sound field programs .......................................... 48

Selecting sound field programs ............................... 48

Sound field program descriptions ............................ 48

Enjoying unprocessed input sources

(Straight decoding mode) .................................... 51

Using audio features ............................................. 52

Adjusting the speaker level...................................... 52

Enjoying pure hi-fi sound ........................................ 52

Adjusting the tonal quality....................................... 52

FM/AM tuning ...................................................... 53

Overview.................................................................. 53

Basic tuning operations............................................ 53

Using station preset feature ..................................... 54

XM Satellite Radio tuning ................................... 57

Connecting the XM Mini-Tuner Dock .................... 57

Activating XM Satellite Radio ................................ 58

Basic XM Satellite Radio operations....................... 58

Setting the XM Satellite Radio

preset channels .................................................... 60

Displaying the XM Satellite Radio

information .......................................................... 61

SIRIUS Satellite Radio™ tuning .........................62

Connecting the SiriusConnect™ tuner .................... 62

Activating SIRIUS Satellite Radio™

subscription ......................................................... 63

Basic SIRIUS Satellite Radio™ operations ............ 63

Setting the SIRIUS Satellite Radio™

preset channels .................................................... 65

Setting the Parental Lock......................................... 65

Displaying the SIRIUS Satellite Radio™

information .......................................................... 67

Using iPod™ ..........................................................68

Controlling iPod™................................................... 68

Using Bluetooth™ components ............................70

Pairing the Bluetooth™ adapter and your

Bluetooth™ component....................................... 70

Playback of the Bluetooth™ component ................. 70

Recording ...............................................................71

Advanced sound configurations...........................72

Changing sound field parameter settings................. 72

Selecting decoders ................................................... 78

Customizing this unit (MANUAL SETUP).........80

Using SET MENU ................................................... 84

1 BASIC MENU...................................................... 85

2 VOLUME MENU ................................................ 89

3 SOUND MENU.................................................... 90

4 INPUT MENU...................................................... 93

5 OPTION MENU................................................... 96

Remote control features......................................100

Controlling this unit, a TV, or other components

.......... 100

Setting remote control codes ................................. 102

Using multi-zone configuration..........................103

Connecting Zone 2................................................. 103

Controlling Zone 2................................................. 104

Advanced setup....................................................106

Using the advanced setup ...................................... 106

Troubleshooting...................................................110

Resetting the system............................................119

Glossary................................................................120

Sound field program information......................123

Specifications .......................................................124

Index .....................................................................126

(at the end of this manual)

Front panel................................................................i

Remote control ....................................................... ii

List of remote control codes ................................. iii

Contents

INTRODUCTION

PREPARATION

BASIC OPERATION

ADVANCED OPERATION

ADDITIONAL INFORMATION

APPENDIX

“

A

SPEAKERS” or “

4

DVD” (example) indicates the name

of the parts on the front panel or the remote control. Refer to

the attached sheet or the pages at the end of this manual for

the information about each position of the parts.

FEATURES

2 En

Built-in 7-channel power amplifier

◆ Minimum RMS output power

(20 Hz to 20 kHz, 0.06% THD, 8 Ω)

Front: 95 W + 95 W

Center: 95 W

Surround: 95 W + 95 W

Surround back: 95 W + 95 W

SCENE function

◆ Preset SCENE templates for various situations

◆ SCENE templates for customizing capability

◆ Controlling Yamaha SCENE control signal support

component (some models only) working with the SCENE

function

Sound field programs

◆ Proprietary Yamaha technology for the creation of sound

fields

◆ Compressed Music Enhancer mode

◆ Virtual CINEMA DSP

◆ SILENT CINEMA

Digital audio decoders

◆ Dolby TrueHD, Dolby Digital Plus decoder

◆ DTS-HD Master Audio, DTS-HD High Resolution Audio

decoder

◆ Dolby Digital/Dolby Digital EX decoder

◆ DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS 96/24 decoder

◆ Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic IIx

decoder

◆ Neural Surround decoder

Radio tuners

◆ FM/AM tuning capability

◆ XM Satellite Radio tuning capability (using XM Mini-Tuner

and Home Dock, sold separately)

◆ SIRIUS Satellite Radio™ tuning capability (using

SiriusConnect tuner, sold separately)

HDMI™ (High-Definition Multimedia Interface)

◆ HDMI interface for standard, enhanced or

high-definition video as well as multi-channel digital audio

based on HDMI version 1.3a (HDMI is Licensed by HDMI

Licensing, LLC.)

– Automatic audio and video synchronization (lip sync)

information capability

– Deep Color video signal (30/36 bit) transmission capability

– “x.v.Color” video signal transmission capability

– High refresh rate and high resolution video signals

capability

– High definition digital audio format signals capability

◆ HDCP (High-bandwidth Digital Content Protection System)

licensed by Digital Content Protection, LLC.

◆ Analog video to HDMI digital video up-conversion

(composite video ↔ S-video ↔ component video → HDMI

digital video) capability for monitor out

DOCK terminal

◆ DOCK terminal to connect a Yamaha iPod universal dock

(such as YDS-10, sold separately) or Bluetooth adapter (such

as YBA-10, sold separately)

Other features

◆ YPAO (Yamaha Parametric Room Acoustic Optimizer) for

automatic speaker setup

◆ 192-kHz/24-bit D/A converter

◆ OSD (on-screen display) menus that allow you to optimize

this unit to suit your individual audiovisual system

◆ 5.1 or 7.1-channel additional input jacks for discrete multi-

channel input

◆ Component video input/output capability includes

(3 COMPONENT VIDEO INs and 1 MONITOR OUT)

◆ Digital video signal conversion (composite video ↔ S-video

↔ component video) capability for monitor out

◆ Pure Direct mode for pure hi-fi sound for all sources

◆ Adaptive dynamic range controlling capability

◆ Adaptive DSP effect level controlling capability

◆ iPod controlling capability

◆ Remote control with preset remote control codes capability

◆ Zone 2 custom installation facility

◆ Bi-amplification connection capability

◆ Sleep timer

Check that you received all of the following parts.

❏ Remote control

❏ Batteries (2) (AAA, R03, UM-4)

❏ Optimizer microphone

❏ AM loop antenna

❏ Indoor FM antenna

Features

Supplied accessories

Notice

3 En

INTRODUCTION

English

We Want You Listening For A Lifetime

Yamaha and the Electronic Industries Association’s

Consumer Electronics Group want you to get the

most out of your equipment by playing it at a safe

level. One that lets the sound come through loud and

clear without annoying blaring or distortion – and,

most importantly, without affecting your sensitive

hearing. Since hearing damage from loud sounds is often

undetectable until it is too late, Yamaha and the Electronic

Industries Association’s Consumer Electronics Group

recommend you to avoid prolonged exposure from excessive

volume levels.

Manufactured under license from Dolby Laboratories.

“Dolby”, “Pro Logic”, and the double-D symbol are trademarks

of Dolby Laboratories.

Manufactured under license under U.S. Patent No’s:

5,451,942;5,956,674;5,974,380;5,978,762;6,226,616;6,487,535

& other U.S. and worldwide patents issued & pending. DTS is a

registered trademark and the DTS logos, Symbol, DTS-HD and

iPod™

“iPod” is a trademark of Apple Inc., registered in the U.S. and

other countries.

Bluetooth™

Bluetooth is a registered trademark of the Bluetooth SIG and is

used by Yamaha in accordance with a license agreement.

“HDMI”, the “HDMI” logo and “High-Definition Multimedia

Interface” are trademarks or registered trademarks of HDMI

Licensing LLC.

x.v.Color™

“x.v.Color” is a trademark of Sony Corporation.

“SILENT CINEMA” is a trademark of Yamaha Corporation.

The XM name and related logos are registered trademarks of XM

Satellite Radio Inc.

Neural Surround

™

name and related logos are trademarks owned

by Neural Audio Corporation.

the SIRIUS dog logo, channel names and logos are trademarks of

SIRIUS Satellite Radio Inc.

Notice

About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using either the

buttons on the front panel or the ones on the remote

control. In case the button names differ between the front

panel and the remote control, the button name on the

remote control is given in parentheses.

• This manual is printed prior to production. Design and

specifications are subject to change in part as a result of

improvements, etc. In case of differences between the

manual and product, the product has priority.

•“

A

SPEAKERS” or “

4

DVD” (example) indicates the

name of the parts on the front panel or the remote control.

Refer to the attached sheet or the pages at the end of this

manual for the information about each position of the

parts.

•

The symbol “☞ ” with page number(s) indicates the

corresponding reference page(s).

GETTING STARTED

4 En

■ Installing batteries in the remote control

1 Take off the battery compartment cover.

2 Insert the two supplied batteries

(AAA, R03, UM-4) according to the polarity

markings (+ and –) on the inside of the

battery compartment.

3 Snap the battery compartment cover back

into place.

• Change all of the batteries if you notice that the operation range

of the remote control decreases.

• Do not use an old battery and a new one together.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and

color.

• If the batteries have leaked, dispose of them immediately. Avoid

touching the leaked material or letting it come into contact with

clothing, etc. Clean the battery compartment thoroughly before

installing new batteries.

• Do not throw away batteries with general house waste; dispose

of them correctly in accordance with your local regulations.

• If the remote control is without batteries for more than 2

minutes, or if exhausted batteries remain in the remote control,

the contents of the memory may be cleared. When the memory

is cleared, insert new batteries and set up the remote control

code.

■ VOLTAGE SELECTOR

(Asia and General models only)

Getting started

Notes

1

3

2

Caution

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local voltage BEFORE

plugging the power cable into the AC wall outlet.

Improper setting of the VOLTAGE SELECTOR may

cause damage to this unit and create a potential fire

hazard.

Rotate the VOLTAGE SELECTOR clockwise or

counterclockwise to the correct position using a

straight slot screwdriver.

Voltages are as follows:

Asia model ................... 220/230–240 V AC, 50/60 Hz

General model

..................... 110/120/220/230–240 V AC, 50/60 Hz

230-

240V

VOLTAGE

SELECTOR

Voltage indication

Quick start guide

5 En

INTRODUCTION

English

The following steps describe the easiest way to enjoy DVD movie playback in your home theater. See pages 11 to 15 for

details of the speaker placement.

Prepare the following items.

❏ Speakers

❏ Front speakers ...................................x 2

❏ Center speaker ..................................x 1

❏ Surround speakers ............................ x 4

Select magnetically shielded speakers. The

minimum required speakers are two front speakers.

The priority of the requirement of other speakers is

as follows:

1. Two surround speakers

2. Center speaker

3. One (or two) surround back speaker(s)

❏ Active subwoofer ................................... x 1

Select an active subwoofer equipped with an RCA

input jack.

❏ Speaker cables ....................................... x 7

❏ Subwoofer cable .................................... x 1

Select a monaural RCA cable.

❏ DVD player .............................................. x 1

Select DVD player equipped with coaxial digital

audio output jack and composite video output

jack.

❏ Video monitor ......................................... x 1

Select a TV monitor, video monitor or projector

equipped with a composite video input jack.

❏ Video cable ............................................. x 2

Select an RCA composite video cable.

❏ Digital coaxial audio cable .................... x 1

y

You can also connect two subwoofers to this unit. In this

case, prepare two active subwoofers and subwoofer cables.

Quick start guide

Front right

speaker

Subwoofer

Surround back

right speaker

Surround left

speaker

Front left

speaker

Surround back left

speaker

Surround right

speaker

Center

speaker

Video monitor

DVD player

Enjoy DVD playback!

Step 1: Set up your speakers

☞

P. 6

Step 2: Connect your DVD player

and other components

Step 3: Press SCENE 1 button

☞

P. 7

☞

P. 8

Preparation: Check the items

Quick start guide

6 En

Place your speakers in the room and connect them to this

unit.

1 Place your speakers and subwoofer in the

room.

2 Connect speaker cables to each speaker.

Be sure to connect the “+” (red) and “–” (black) properly.

Cables are colored or shaped differently, perhaps with a

stripe, groove or ridge. Connect the striped (grooved, etc.)

cable to the “+” (red) terminals of this unit and your speaker.

Connect the plain cable to the “–” (black) terminals.

3 Connect each speaker cable to the

corresponding speaker terminal of this unit.

Be sure to connect the left channel (L), right channel

(R), “+” (red) and “–” (black) properly.

Front speakers and center speaker

Surround and surround back speakers

4 Connect the subwoofer cable to the

SUBWOOFER PRE OUT 1 jack of this unit

and the input jack of the subwoofer.

y

You can also connect another subwoofer to the SUBWOOFER

PRE OUT 2 jack.

Step 1: Set up your speakers

AC OUTLETS

SWITCHED

120V 80Hz

100W MAX. TOTAL

0.8A MAX. TOTAL

R

L

AUDIO MULTI CH INPUT PRE OUT DOCK VIDEO

COMPONENT VIDEO

HDMI

DIGITAL INPUT

XM

ANTENNA

REMOTE

SIRIUS

TRIGGER

OUT

SPEAKERS

DVDSUBWOOFERFRONTSB (8CH) ZONE 2

OUT

SUB

WOOFER

SUR. BACKSURROUND

SINGLE CENTERCENTERFRONT (8CH)

SURROUND

DVD

DTV/CBL

S VIDEO

VIDEO

DTV/CBL

DVR

DVRMONITOR OUT

VCR

OUTININ OUT

1 2

DVD

DVDCDDTV/CBL

OPTICAL COAXIAL

DVD

OUT

SURROUND BACK/BI-AMPSURROUND

SINGLE

CENTERFRONT A

AM

+12V

15mA MAX.

GND

FRONT B/ZONE B/

ZONE 2/PRESENCE

DTV/CBLDVD

CD

MD/

CD-R

IN

(PLAY)

OUT

(REC)

DTV/CBL DVR VCR

OUTININ OUT

IN OUT

MONITOR

OUT

FM

UNBAL.

R

L

R

L

R

L

R

L

4

321

IN2IN1

EXTRA SP

Y

P

R

P

B

Y

P

R

P

B

A B

C

75Ω

Speaker terminals

PRE OUT SUBWOOFER 1 jack

12 3 4

4

1

Make sure that this unit and the subwoofer are

unplugged from the AC wall outlets.

2

Twist the exposed wires of the speaker cables

together to prevent short circuits.

3

Do not let the bare speaker wires touch each

other.

4

Do not let the bare speaker wires touch any

metal part of this unit.

To the front left

speaker

To the front right

speaker

To the center speaker

Loosen Insert Tighten

To the surround

right speaker

To the surround

back left speaker

To the surround

left speaker

To the surround

back right speaker

PRE OUT

DOCK

DVD

SUBWOOFER

SUR. BACK

R

ROUND

SINGLE

CENTER

S VI

D

VID

E

12

SUBWOOFER PRE

OUT 1 jack

Subwoofer cable

Input jack

AV receiverSubwoofer

Quick start guide

7 En

INTRODUCTION

English

1 Connect the digital coaxial audio cable to the

digital coaxial audio output jack of your DVD

player and the DVD DIGITAL INPUT COAXIAL

jack of this unit.

2 Connect the video cable to the composite

video output jack of your DVD player and

DVD VIDEO jack of this unit.

3 Connect the video cable to the VIDEO

MONITOR OUT jack of this unit and the video

input jack of your video monitor.

4 Connect the power plug of this unit and other

components into the AC wall outlet.

y

This unit is equipped with AC OUTLET(S) for the power

supply of the other components (except Korea model). See

page 28 for details.

Step 2: Connect your DVD player

and other components

AC OUTLETS

SWITCHED

120V 80Hz

100W MAX. TOTAL

0.8A MAX. TOTAL

R

L

AUDIO MULTI CH INPUT PRE OUT DOCK VIDEO

COMPONENT VIDEO

HDMI

DIGITAL INPUT

XM

ANTENNA

REMOTE

SIRIUS

TRIGGER

OUT

SPEAKERS

DVDSUBWOOFERFRONTSB (8CH) ZONE 2

OUT

SUB

WOOFER

SUR. BACKSURROUND

SINGLE CENTERCENTERFRONT (8CH)

SURROUND

DVD

DTV/CBL

S VIDEO

VIDEO

DTV/CBL

DVR

DVRMONITOR OUT

VCR

OUTININ OUT

12

DVD

DVDCDDTV/CBL

OPTICAL COAXIAL

DVD

OUT

SURROUND BACK/BI-AMPSURROUND

SINGLE

CENTERFRONT A

AM

+12V

15mA MAX.

GND

FRONT B/ZONE B/

ZONE 2/PRESENCE

DTV/CBLDVD

CD

MD/

CD-R

IN

(PLAY)

OUT

(REC)

DTV/CBL DVR VCR

OUTININ OUT

IN OUT

MONITOR

OUT

FM

UNBAL.

R

L

R

L

R

L

R

L

4

321

IN2IN1

EXTRA SP

Y

P

R

P

B

Y

P

R

P

B

A B

C

75Ω

Make sure that this unit and the DVD

player are unplugged from the AC

wall outlets.

DVD DIGITAL INPUT COAXIAL jack DVD VIDEO jack

VIDEO MONITOR OUT jack

DVD

AUDIO

M

DIGITAL INPUT

SPEAKERS

SB (8C

H

FRONT (8C

H

DVD

CD

OPTICAL

COAXIAL

S

U

CENTER

FRONT A

FRONT B/ZONE B/

ZONE 2/PRESENCE

DVD

D/

D

-R

OUT

(REC)

DTV/CBL

DVR

VCR

O

U

T

IN

IN O

U

T

R

L

R

L

6

5

4

3

IN1

EXTRA SP

Digital coaxial

audio output

jack

Digital coaxial audio

cable

DVD DIGITAL

INPUT COAXIAL

jack

DVD player

AV receiver

DOCK

VIDEO

COMPONENT

V

DVD

DTV/CBL

S VIDEO

V

I

DEO

DVR

OUT

IN

OUT

P

R

Y

P

R

P

B

A

Composite

video output

jack

Video cable

DVD VIDEO jack

DVD player

AV receiver

■ For further connections

• Using the other kind of speaker combinations

☞ P. 11

• Connecting a video monitor via various ways of the

connection ☞ P. 20

• Connecting a DVD player via various ways of the

connection ☞ P. 21

• Connecting a DVD recorder or a digital video

recorder ☞ P. 22

• Connecting a set-top box ☞ P. 22

• Connecting a CD player, an MD recorder or a

turntable ☞ P. 23

• Connecting an external amplifier ☞ P. 24

• Connecting a DVD player via analog multi-channel

audio connection ☞ P. 25

• Connecting a Yamaha iPod universal dock or

Bluetooth adapter ☞ P. 25

• Using the REMOTE IN/OUT jacks ☞ P. 26

• Using the VIDEO AUX jacks on the front panel

☞ P. 26

• Connecting a FM/AM antenna

☞ P. 27

• Connecting the XM Mini-Tuner Dock ☞ P. 57

• Connecting the SiriusConnect tuner ☞ P. 62

VIDEO

COMP

ONENT VIDEO

DVD

DTV/CBL

DVR

VCR

OUT

ININ

OUT

MONITOR

OUT

Y

P

R

P

B

Y

P

B

C

Video monitor

AV receiver

Video cable

VIDEO

MONITOR OUT

jack

Video input jack

Quick start guide

8 En

1 Turn on the video monitor and then set the

input source selector of the video monitor to

this unit.

2 Press

S

SCENE1 button.

This unit is turned on. “DVD Viewing” appears in the

front panel display, and this unit automatically

optimize own status for the DVD playback.

y

The indicator on the selected SCENE button lights up while

this unit is in the SCENE mode.

3 Start playback of the desired DVD on your

player.

4 Rotate

J

VOLUME to adjust the volume.

When you change the input source or sound field program,

the SCENE mode is deactivated.

■ About SCENE function

Just by pressing one SCENE button, you can turn on this

unit and recall your favorite input source and sound field

program according to the SCENE template that has been

assigned to the SCENE button. The SCENE templates are

built combinations of input sources and sound field

programs.

y

If you connect a Yamaha product that has capability of the

SCENE control signals, this unit can automatically activate the

component and start playback. Refer to the instruction manual of

the DVD player for further information.

■ The default assigned SCENE templates

*1

You must connect a cable TV or a satellite tuner to this unit in

advance. See page 22 for details.

*2

You need to connect the supplied FM and AM antennas to this

unit in advance. See page 27 for details.

*3

You must tune into the desired radio station in advance. See

pages 53 to 56 for tuning information.

*4

To achieve the best possible reception, orient the connected

AM loop antenna, or adjust the position of the end of the

indoor FM antenna.

y

You can change the assigned SCENE template for the SCENE

buttons. See page 37 for details.

Step 3: Press SCENE 1 button

Check the type of the connected speakers.

If the speakers are 6 ohm speakers, set “SP IMP.” to

“6Ω MIN” before using this unit (see page 28). 4 ohm

speakers can be also used as the front speakers (see

page 106).

Note

Default

SCENE

button

The name of the SCENE template

and its description

SCENE

1

DVD Viewing

– input source: DVD

– sound field program: Straight

For when you want to listen to a music disc from

the connected DVD player as the background

music for this room.

SCENE

2

Disc Listening

– input source: DVD

– sound field program: 7ch Stereo

For when you want to listen to a music disc from

the connected DVD player as the background

music for this room.

SCENE

3

TV Viewing

*1

– input source: DTV/CBL

– sound field program: Straight

For when you want to watch a TV program.

SCENE

4

Radio Listening

*2, *3, *4

– input source: TUNER

– sound field program: 7ch Enhancer

For when you want to listen to a music program

from the FM radio station.

Notes

Quick start guide

9 En

INTRODUCTION

English

■ After using this unit...

Press

K

MAIN ZONE ON/OFF to set this unit to

the standby mode.

This unit is set to the standby mode and consumes a small

amount of power in order to receive infrared signals from

the remote control. To turn on this unit from the standby

mode, press the desired

S

SCENE buttons

(or

6

SCENE) or

K

MAIN ZONE ON/OFF

(or

H

POWER). See page 29 for details.

What do you want to do with this

unit?

■ Customizing the SCENE templates

• Using various SCENE templates ☞ P. 37

• Creating your original SCENE templates

☞ P. 40

■ Using various input sources

• Basic controls of this unit ☞ P. 42

• Enjoying FM/AM radio programs ☞ P. 53

• Enjoying XM Satellite Radio programs ☞ P. 57

• Enjoying SIRIUS Satellite Radio programs

☞ P. 62

• Using your iPod with this unit ☞ P. 68

• Using the Bluetooth components ☞ P. 70

■ Using various sound features

• Using various sound field programs ☞ P. 48

• Using the pure direct mode for high

fidelity sound ☞ P. 52

• Customizing the sound field programs ☞ P. 72

■ Adjusting the parameters of this unit

• Automatically optimizing the speaker parameters

for your listening room (AUTO SETUP) ☞ P. 32

• Manually adjusting various parameters of this unit

☞ P. 80

• Setting the remote control ☞ P. 100

• Adjusting the advanced parameters ☞ P. 106

■ Additional feature

• Automatically turning off this unit ☞ P. 47

CONNECTIONS

10 En

9

TRIGGER OUT jack

This is control expansion jack for custom installation.

Connections

Rear panel

AC OUTLETS

SWITCHED

120V 80Hz

100W MAX. TOTAL

0.8A MAX. TOTAL

R

L

AUDIO MULTI CH INPUT PRE OUT DOCK VIDEO

COMPONENT VIDEO

HDMI

DIGITAL INPUT

XM

ANTENNA

REMOTE

SIRIUS

TRIGGER

OUT

SPEAKERS

DVDSUBWOOFERFRONTSB (8CH) ZONE 2

OUT

SUB

WOOFER

SUR. BACKSURROUND

SINGLE CENTERCENTERFRONT (8CH)

SURROUND

DVD

DTV/CBL

S VIDEO

VIDEO

DTV/CBL

DVR

DVRMONITOR OUT

VCR

OUTININ OUT

12

DVD

DVDCDDTV/CBL

OPTICAL COAXIAL

DVD

OUT

SURROUND BACK/BI-AMPSURROUND

SINGLE

CENTERFRONT A

AM

+12V

15mA MAX.

GND

FRONT B/ZONE B/

ZONE 2/PRESENCE

DTV/CBLDVD

CD

MD/

CD-R

IN

(PLAY)

OUT

(REC)

DTV/CBL DVR VCR

OUTININ OUT

IN OUT

MONITOR

OUT

FM

UNBAL.

R

L

R

L

R

L

R

L

4

321

IN2IN1

EXTRA SP

Y

P

R

P

B

Y

P

R

P

B

A B

C

75Ω

12 34567

89 0 AB

C

Name Page

1 XM jack

(U.S.A. and Canada models only)

57

SIRIUS jack

(U.S.A. and Canada models only)

62

2 AUDIO jacks

21

DIGITAL INPUT/OUTPUT jacks

17-23

3 MULTI CH INPUT jacks

25

4 ZONE2 OUT jacks

103

5 PRE OUT jacks

24

6 DOCK terminal

25

7 Video component jacks

(VIDEO and S VIDEO)

17-22

COMPONENT VIDEO jacks

17-22

8 ANTENNA terminals

27

9 REMOTE IN/OUT jacks

26

0 Speaker terminals

11-16

A HDMI jacks

18

B VOLTAGE SELECTOR

(Asia and General models only)

4

C AC OUTLET(S)

28

11 En

Connections

PREPARATION

English

The speaker layout below shows the speaker setting we recommend. You can use it to enjoy the CINEMA DSP and

multi-channel audio sources.

■ 7.1-channel speaker layout

7.1-channel speaker layout is highly recommended for playback the sound of high definition audio formats (Dolby

TrueHD, DTS-HD Master Audio, etc.) as well as the conventional audio sources with sound field programs. See page 14

for connection information.

y

We recommend that you also add the presence speakers for the effect sounds of the CINEMA DSP sound field program. See page 13 for

details.

Front left and right speakers

The front speakers are used for the main source sound plus effect sounds. Place these speakers at an equal distance from the

ideal listening position. The distance of each speaker from each side of the video monitor should be the same.

Center speaker

The center speaker is for the center channel sounds (dialog, vocals, etc.). If for some reason it is not practical to use a

center speaker, you can do without it. Best results, however, are obtained with the full system.

Surround left and right speakers

The surround speakers are used for effect and surround sounds.

Surround back left and right speakers

The surround back speakers supplement the surround speakers and provide more realistic front-to-back transitions.

Subwoofer(s)

The use of a subwoofer with a built-in amplifier, such as the Yamaha Active Servo Processing Subwoofer System, is

effective not only for reinforcing bass frequencies from any or all channels, but also for reproducing the high fidelity

sound of the LFE (low-frequency effect) channel included in Dolby Digital and DTS sources. You can connect one or

two subwoofer(s) to this unit. When you use two subwoofers, you can enjoy deeper bass sound. The position of the

subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer

near the front speakers. Turn it slightly toward the center of the room to reduce wall reflections.

y

When you use two subwoofers, select the same type of the subwoofer as another and set these subwoofers as same sound characteristics.

Place each subwoofer at the same distance from the listening position. The signal output at the SUBWOOFER PRE OUT 2 is the same

as the one output at the SUBWOOFER PRE OUT 1 jack.

Placing speakers

FR

FL

SBR

SBL

SL

SR

C

SW

60˚

30˚

80˚

FR

SBL

SBR

SL

C

SR

FL

Speaker indications

FL/FR: Front left/right

C: Center

SL/SR: Surround left/right

SBL/SBR: Surround back left/right

SW: Subwoofer

30 cm (12 in) or more

12 En

Connections

■ 6.1-channel speaker layout

See page 14 for connection information.

y

We recommend that you also add the presence speakers for the

effect sounds of the CINEMA DSP sound field program. See

page 13 for details.

Front left and right speakers

Center speaker

Surround left and right speakers

Subwoofer(s)

The functions and settings of each speaker are the same as

those for the 7.1-channel speaker layout (see page 11).

Surround back speaker

Connect a single surround speakers to the SURROUND

BACK SINGLE speaker terminal and place the single

surround back speaker behind the listening position. The

surround back left and right channel signals are mixed

down and output at the single surround back speaker when

you set “SUR.B L/R SP” to “SMLx1” or “LRGx1” (see

page 86).

■ 5.1-channel speaker layout

See page 14 for connection information.

y

We recommend that you also add the presence speakers for the

effect sounds of the CINEMA DSP sound field program. See

page 13 for details.

Front left and right speakers

Center speaker

Subwoofer(s)

The functions and settings of each speaker are the same as

those for the 7.1-channel speaker layout (see page 11).

Surround left and right speakers

Connect the surround speakers to the SURROUND

speaker terminals even if you place the surround speakers

behind the listening position. For the smooth and

unbroken sound field behind the listening position, place

the surround left and right speakers farther back compared

with the placement in the 7.1-channel speaker layout. The

surround back channel signals are directed to the surround

left and right speakers when “SUR.B L/R SP” is set to

“NONE” (see page 86).

FR

FL

SB

SL

SR

C

SW

60˚

30˚

80˚

FR

SB

SL

C

SR

FL

Speaker indications

FL/FR: Front left/right

C: Center

SL/SR: Surround left/right

SB: Surround back

SW: Subwoofer

FR

FL

SL

SR

SW

C

60˚

30˚

80˚

FR

SL

C

SR

FL

Speaker indications

FL/FR: Front left/right

C: Center

SL/SR: Surround left/right

SW: Subwoofer

For other speaker combinations

You can enjoy multi-channel sources with sound field programs by using a speaker combination other than the 7.1/

6.1/5.1-channel speaker combinations.

Use the automatic setup feature (see page 32) or set the “SPEAKER SET” parameters in “MANUAL SETUP” (see

page 85) to output the surround sounds at the connected speakers.

13 En

Connections

PREPARATION

English

■ Using presence speakers

The presence speakers supplement the sound from the front and surround back speakers with extra ambient effects

produced by the sound field programs (see page 48). You can adjust the vertical position of dialogues with using the

presence speakers (see page 73).

To use the presence speakers, connect the speakers to the EXTRA SP terminal (see page 14) and set “EXTRA SP

ASSIGN” to “PRESENCE” (see pages 33 and 85).

FR

PRPL

C

FL

0.5 to 1 m (1 to 3 ft)

1.8 m

(6 ft) or

higher

Speaker indications

FL: Front left

FR: Front right

C: Center

PL: Front presence left

PR: Front presence right

0.5 to 1 m (1 to 3 ft)

1.8 m

(6 ft) or

higher

14 En

Connections

Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,

this unit cannot reproduce the input sources accurately.

A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a stripe,

groove or ridge. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker. Connect the plain cable

to the “–” (black) terminals.

■ For the 7.1-channel speaker setting

Connecting speakers

Caution

• Before connecting the speakers, make sure that the AC power plug is disconnected from the AC wall outlet.

• Do not let the bare speaker wires touch each other or let them touch any metal part of this unit. This could damage

this unit and/or the speakers. If the speaker wires are short-circuited, “CHECK SP WIRES” appears in the front

panel display when you turn on this unit.

• Use the magnetically shielded speakers. If this type of speaker still creates interference with the monitor, place the

speakers away from the monitor.

• If you are to use 6 ohm speakers, be sure to set “SP IMP.” to “6Ω MIN” before using this unit (see page 28). 4 ohm

speakers can be also used as the front speakers. For details about the speaker impedance setting, see page 106.

Note

AC OUTLETS

SWITCHED

120V 80Hz

100W MAX. TOTAL

0.8A MAX. TOTAL

R

L

AUDIO MULTI CH INPUT PRE OUT DOCK VIDEO

COMPONENT VIDEO

HDMI

DIGITAL INPUT

XM

ANTENNA

REMOTE

SIRIUS

TRIGGER

OUT

SPEAKERS

DVDSUBWOOFERFRONTSB (8CH) ZONE 2

OUT

SUB

WOOFER

SUR. BACKSURROUND

SINGLE CENTERCENTERFRONT (8CH)

SURROUND

DVD

DTV/CBL

S VIDEO

VIDEO

DTV/CBL

DVR

DVRMONITOR OUT

VCR

OUTININ OUT

12

DVD

DVDCDDTV/CBL

OPTICAL COAXIAL

DVD

OUT

SURROUND BACK/BI-AMPSURROUND

SINGLE

CENTERFRONT A

AM

+12V

15mA MAX.

GND

FRONT B/ZONE B/

ZONE 2/PRESENCE

DTV/CBLDVD

CD

MD/

CD-R

IN

(PLAY)

OUT

(REC)

DTV/CBL DVR VCR

OUTININ OUT

IN OUT

MONITOR

OUT

FM

UNBAL.

R

L

R

L

R

L

R

L

4

321

IN2IN1

EXTRA SP

Y

P

R

P

B

Y

P

R

P

B

A B

C

75Ω

Front speakers

(FRONT A)

Surround speakers

Subwoofers

Right

Center speaker

Surround back speakers

Left

Right

EXTRA SP terminals

Connect the alternative front speaker system (FRONT B), front speaker systems in another room

(ZONE B), presence speakers, or Zone 2 speakers. To select the function of the speakers connected

to the EXTRA SP terminals, set the “EXTRA SP ASSIGN” parameter in “SOUND MENU” (see

page 85).

y

You can also select the function of the speakers connected to the EXTRA SP terminals in “AUTO

SETUP” (see page 33).

(optional)

15 En

Connections

PREPARATION

English

■ For the 6.1-channel speaker setting

■ For the 5.1-channel speaker setting

Surround back speaker

AUDIO MULTI CH INPUT PRE OUT DOCK

HDMI

DIGITAL INPUT

T

RIGGER

OUT

SPEAKERS

SUBWOOFERFRONTSB (8CH) ZONE 2

OUT

SUB

WOOFER

SUR. BACKSURROUND

SINGLE CENTERCENTERFRONT (8CH)

SURROUND

12

DVD

DVDCDDTV/CBL

OPTICAL COAXIAL

DVD

OUT

SURROUND BACK/BI-AMPSURROUND

SINGLE

CENTERFRONT A

2V

5

mA MAX.

FRONT B/ZONE B/

ZONE 2/PRESENCE

DTV/CBLDVD

MD/

CD-R

IN

(PLAY)

OUT

(REC)

DTV/CBL DVR VCR

OUTININ OUT

R

L

R

L

R

L

R

L

4

321

IN2IN1

EXTRA SP

Surround speakers

EXTRA SP terminals

(see page 14)

Left (SINGLE)

Center speaker

LeftRight

Front speakers

(FRONT A)

LeftRight

Subwoofers

(optional)

AUDIO MULTI CH INPUT PRE OUT DOCK

HDMI

DIGITAL INPUT

T

RIGGER

OUT

SPEAKERS

SUBWOOFERFRONTSB (8CH) ZONE 2

OUT

SUB

WOOFER

SUR. BACKSURROUND

SINGLE CENTERCENTERFRONT (8CH)

SURROUND

12

DVD

DVDCDDTV/CBL

OPTICAL COAXIAL

DVD

OUT

SURROUND BACK/BI-AMPSURROUNDCENTERFRONT A

2V

mA MAX.

FRONT B/ZONE B/

ZONE 2/PRESENCE

DTV/CBLDVD

MD/

CD-R

IN

(PLAY)

OUT

(REC)

DTV/CBL DVR VCR

OUTININ OUT

R

L

R

L

R

L

R

L

4

321

IN2IN1

EXTRA SP

SINGLE

Surround speakers

EXTRA SP terminals

(see page 14)

Center speaker

LeftRight

Front speakers

(FRONT A)

LeftRight

Subwoofers

(optional)

16 En

Connections

■ Connecting the speaker cable

1 Remove approximately 10 mm (0.4 in) of

insulation from the end of each speaker

cable and then twist the exposed wires of the

cable together to prevent short circuits.

2 Loosen the knob.

3 Insert one bare wire into the hole on the side

of each terminal.

4 Tighten the knob to secure the wire.

■ Connecting the banana plug

(except Europe, Russia, Asia and Korea

models)

Tighten the knob and then insert the banana plug

connector into the end of the corresponding

terminal.

■ Using bi-amplification connections

This unit allows you to make bi-amplification connections

to one speaker system. Check if your speakers support bi-

amplification.

To make the bi-amplification connections, use the FRONT

and SURROUND BACK/BI-AMP terminals as shown

below. To activate the bi-amplification connections, set

“BI-AMP” to “ON” in “ADVANCED SETUP” (see

page 109).

When you make the conventional connection, make sure that the

shorting bars are put into the terminals appropriately. Refer to the

instruction manuals of the speakers for details.

10 mm (0.4 in)

Red: positive (+)

Black: negative (–)

Caution

Remove the shorting bars or bridges of your speakers

to separate the LPF (low pass filter) and HPF (high

pass filter) crossovers.

Note

Red: positive (+)

Black: negative (–)

FRONT A

SURROUND BACK/

BI-AMP

SINGLE

L

R

L

R

This unit

Left

Right

Front speakers

Страница загружается ...

Yamaha RX V663 - AV Receiver Инструкция по применению

Это руководство также подходит для

Yamaha RX V663 - AV Receiver Инструкция по применению

на других языках

Похожие модели бренда

Модели других брендов