Electrolux ESL66010 Руководство пользователя

user manual

Инструкция по

эксплуатации

návod na používanie

Dishwasher

Посудомоечная машина

Umývačka riadu

ESL66010

Electrolux. Thinking of you.

Share more of our thinking at www.electrolux.com

Contents

Safety information 2

Product description 4

Control panel 4

First use 6

Set the water softener 6

Use of dishwasher salt 7

Use of rinse aid 8

Daily use 9

Load cutlery and dishes 9

Use of detergent 12

Multi-tab function 13

Select and start a washing programme

14

Unloading the dishwasher 15

Washing programmes 16

Care and cleaning 16

What to do if… 18

Technical data 19

Hints for test institutes 19

Installation 20

Water connection 21

Electrical connection 22

Environment concerns 23

Subject to change without notice

Safety information

In the interest of your safety and to en-

sure the correct use, before installing

and first using the appliance, read this

user manual carefully, including its hints

and warnings. To avoid unnecessary

mistakes and accidents, it is important

to ensure that all people using the appli-

ance are thoroughly familiar with its op-

eration and safety features. Save these

instructions and make sure that they re-

main with the appliance if it is moved or

sold, so that everyone using it through

its life will be properly informed on appli-

ance use and safety.

Correct use

• This dishwasher is only intended for wash-

ing household utensils suitable for ma-

chine washing.

• Do not put any solvents in the dishwasher.

This could cause an explosion.

• Knives and other items with sharp points

must be loaded in the cutlery basket with

their points down or placed in a horizontal

position in the upper basket.

• Only use products (detergent, salt and

rinse aid) suitable for dishwashers.

• Avoid opening the door whilst the appli-

ance is in operation, hot steam may es-

cape.

• Do not take any dishes out of the dish-

washer before the end of the washing cy-

cle.

• After use, isolate the appliance from the

power supply and turn off the water sup-

ply.

• This product should be serviced only by an

authorized service engineer, and only gen-

uine spare parts should be used.

• Under no circumstances should you at-

tempt to repair the machine yourself. Re-

pairs carried out by inexperienced persons

could cause injury or serious malfunction-

ing. Contact your local Service Force Cen-

tre. Always insist on genuine spare parts.

General safety

• Persons (including children) with reduced

physical sensory, mental capabilities or

lack of experience and knowledge must

not use the appliance. They must have su-

pervision or instruction for the operation of

the appliance by a person responsible for

their safety.

2 electrolux

• Dishwasher detergents can cause chemi-

cal burns to eyes, mouth and throat. Could

endanger life! Comply with the safety in-

structions of the dishwasher detergent

manufacturer.

• Water in the dishwasher is not for drinking

purposes. Detergent residue may still be

present in your machine.

• Ensure that the door of the dishwasher is

always closed when it is not being loaded

or unloaded. In this way you will avoid any-

body tripping over the open door and hurt-

ing themselves.

• Do not sit or stand on the open door.

Child safety

• This appliance is designed to be operated

by adults. Children must be supervised to

ensure that they do not play with the ap-

pliance.

• Keep all packaging well away from chil-

dren. There is a risk of suffocation.

• Keep all detergents in a safe place out of

children’s reach.

• Keep children well away from the dish-

washer when the door is open.

Installation

• Check your dishwasher for any transport

damage. Never connect a damaged ma-

chine. If your dishwasher is damaged con-

tact your supplier.

• All packaging must be removed before

use.

• Any electrical and plumbing work required

to install this appliance must be carried out

by a qualified and competent person.

• For safety reasons it is dangerous to alter

the specifications or attempt to modify this

product in any way.

• Never use the dishwasher if the electrical

supply cable and water hoses are dam-

aged; or if the control panel, work top or

plinth area are damaged such that the in-

side of the appliance is freely accessible.

Contact your local Service Force centre, in

order to avoid hazard.

• All sides of the dishwasher must never be

drilled to prevent damage to hydraulic and

electric components.

Warning! For electrical and water

connection carefully follow the

instructions given in the specific

paragraphs.

electrolux 3

Product description

1 Upper basket

2 Water hardness dial

3 Salt container

4 Detergent dispenser

5 Rinse aid dispenser

6 Rating plate

7 Filters

8 Lower spray arm

9 Upper spray arm

Control panel

4 electrolux

1 On/Off button

2 Digital display

3 Delay start button

4 Programme selection buttons

5 Indicator lights

6 Function buttons

Indicator lights

Salt Comes on when the special salt has run out.

Rinse aid Comes on when the rinse aid has run out.

Multitab Indicates the activation/deactivation of the 'Multi-

tab function' (refer to 'Multitab function').

The digital display

The digital display indicates:

• the level of hardness to which the water

softener is set,

• the approximate remaining time of the run-

ning programme,

• activation/deactivation of the rinse aid dis-

penser ( ONLY with 'Multitab function ac-

tive'),

• the end of a washing programme (the dig-

ital display shows a zero),

• the countdown for the delay start,

• fault codes concerning malfunction of the

dishwasher,

• if the audible signals are activated/deacti-

vated.

Function buttons

The following functions can be set using

these buttons:

• setting the water softener level,

• cancelling a washing programme or a de-

lay start in progress,

• activation/deactivation of the Multitab

function,

• activation/deactivation of the rinse aid dis-

penser when Multitab function is active,

• activation/deactivation of the audible sig-

nals.

Setting mode

Press the On/Off button; if ALL programme

button lights are on the appliance is in setting

mode.

Always remember that when performing

the following operations:

– selecting a washing programme,

– setting the water softener level,

– activating/deactivating the rinse aid,

– activating/deactivating the audible

signals,

the appliance MUST be in setting mode.

Press the On/Off button; if a programme but-

ton light is on the last performed or selected

programme is still set. In this case, to return

to setting mode, the programme has to be

cancelled.

To cancel a set programme or a

programme in progress

Simultaneously press and hold the two func-

tion buttons B and C until all the programme

button lights come on. The programme has

been cancelled and the machine is now in

setting mode.

Audible signals

Audible signals have been introduced to help

indicate which operations the dishwasher is

performing:

– setting of the water softener,

– end of the washing programme,

– intervention of an alarm due to malfunction

of the machine.

Factory setting: audible signals activated

It is possible to deactivate the audible

signals.

Deactivation/activation of the audible

signals

1. Press the On/Off button. The dishwasher

must be in setting mode.

electrolux 5

2. Simultaneously press and hold function

buttons B and C until the lights of function

buttons A, B and C start flashing.

3. Press function button C, the lights of

function buttons A and B go off while the

light of function button C continues to

flash. The digital display shows the cur-

rent level.

Audible signals deactivated

Audible signals activated

4. To change the setting, press function

button C again; the digital display shows

the new setting.

5. 5. To memorize the operation, switch off

the dishwasher.

First use

Before using your dishwasher for the first

time:

• Ensure that the electrical and water con-

nections comply with the installation in-

structions

• Remove all packaging from inside the ap-

pliance

• Set the water softener level

• Pour 1 litre of water into the salt container

and then fill with dishwasher salt

• Fill the rinse aid dispenser

If you want to use combi detergent

tablets such as: ''3 in 1'', ''4 in 1'', ''5

in 1'' etc... set the Multitab function.

(See ''Multitab function'').

Set the water softener

The dishwasher is equipped with a water

softener designed to remove minerals and

salts from the water supply, which would

have a detrimental or adverse effect on the

operation of the appliance.

The higher the content of these minerals and

salts, the harder your water is. Water hard-

ness is measured in equivalent scales, Ger-

man degrees (dH°), French degrees (°TH)

and mmol/l (millimol per litre - international

unit for the hardness of water).

The softener should be adjusted according

to the hardness of the water in your area.

Your local Water Authority can advise you on

the hardness of the water in your area.

The water softener must be set in two

ways: manually, using the water hard-

ness dial and electronically.

Water hardness Adjusting the water hardness setting Use of

salt

°dH °TH mmol/l manually electronically

51 - 70 91 - 125 9,1 - 12,5 2 level 10 yes

43 - 50 76 - 90 7,6 - 9,0 2 level 9 yes

37 - 42 65 - 75 6,5 - 7,5 2 level 8 yes

29 - 36 51 - 64 5,1 - 6,4 2 level 7 yes

23 - 28 40 - 50 4,0 - 5,0 2 level 6 yes

19 - 22 33 - 39 3,3 - 3,9 2 level 5 yes

15 - 18 26 - 32 2,6 - 3,2 1 level 4 yes

11 - 14 19 - 25 1,9 - 2,5 1 level 3 yes

4 - 10 7 - 18 0,7 - 1,8 1 level 2 yes

< 4 < 7 < 0,7 1 level 1 no

Setting manually

The dishwasher is factory set at position

2.

1. Open the dishwasher door.

2. Remove the lower basket from the dish-

washer.

6 electrolux

3. Turn the water hardness dial to position

1 or 2 (see chart).

4. Replace the lower basket.

Setting electronically

The dishwasher is factory set at level 5.

1. Press the On/Off button. The dishwasher

must be in setting mode.

2. Simultaneously press and hold function

buttons B and C, until the lights of func-

tion buttons A, B and C start flashing.

3.

Press function button A, the lights of

function buttons B and C go off while the

light of function button A continues to

flash. The digital display shows the cur-

rent level and a sequence of intermittent

audible signals are heard.

Examples:

displayed, 5 intermittent audible sig-

nals, pause, etc. = level 5

displayed, 10 intermittent audible

signals, pause, etc. = level 10

4. To change the level, press function but-

ton A. Each time the button is pressed

the level changes. (For the selection of the

new level see the chart).

Examples: If the current level is 5, by

pressing function button A once, level 6

is selected.

If the current level is 10, by pressing func-

tion button A once, level 1 is selected.

5. To memorize the operation, switch off the

dishwasher by pressing the On/Off but-

ton.

Use of dishwasher salt

Warning!

Only use salt specifically designed for use in

dishwashers. All other types of salt not spe-

cifically designed for use in a dishwasher, es-

pecially table salt, will damage the water soft-

ener. Only fill with salt just before starting one

of the complete washing programmes. This

will prevent any grains of salt or salty water,

which may have been spilt, remaining on the

bottom of the machine for any period of time,

which may cause corrosion.

To fill:

1. Open the door, remove the lower basket

and unscrew the cap of the salt container

by turning it anticlockwise.

2. Pour 1 litre of water into the container

(this is necessary only before filling

with salt for the first time) .

3. Using the funnel provided, pour in the salt

until the container is full.

4. Replace the cap making sure that there

is no trace of salt on the screw thread or

on the gasket.

5. Replace the cap tightly turning it clock-

wise until it stops with a click.

Do not worry if water overflows from the

unit when filling with salt, this is quite

normal.

electrolux 7

The salt indicator light on the control

panel can remain illuminated for 2-6

hours after the salt has been replen-

ished, assuming the dishwasher re-

mains switched on. If you are using

salt that takes longer to dissolve

then this can take longer. The oper-

ation of the machine is not affected.

Use of rinse aid

Warning! Only use branded rinse aid for

dishwashers.

Never fill the rinse aid dispenser with any

other substances (e.g. dishwasher

cleaning agent, liquid detergent). This

would damage the appliance.

Rinse aid ensures thorough rinsing, and

spot and streak free drying.

Rinse aid is automatically added during

the last rinse.

1. Open the container by pressing the re-

lease button (A).

2. Add the rinse aid in the container. The

maximum level for filling is indicated by

"max".

The dispenser holds about 110 ml of rinse

aid, which is sufficient for between 16 and

40 washing cycles, depending upon the

dosage setting.

3. Ensure that the lid is closed after every

refill.

Clean up any rinse aid spilt during filling

with an absorbent cloth to avoid excess

foaming during the next wash.

According to the finish and drying results ob-

tained, adjust the dose of rinse aid by means

of the 6 position selector (position 1 minimum

dosage, position 6 maximum dosage).

The dose is factory set in position 4.

Increase the dose if there are drops of water

or lime spots on the dishes after washing.

Reduce it if there are sticky whitish streaks

on the dishes or a bluish film on glassware or

knife blades.

8 electrolux

Daily use

• Check if it’s necessary to refill with dish-

washer salt or rinse aid.

• Load cutlery and dishes into the dishwash-

er.

• Fill with dishwasher detergent.

• Select a wash programme suitable for the

cutlery and dishes.

• Start the wash programme.

Helpful hints and tips

Sponges, household cloths and any object

that can absorb water may not be washed in

the dishwasher.

• Before loading the dishes, you should:

– Remove all left over food and debris.

– Soften remnants of burnt food in pans

• When loading the dishes and cutlery,

please note:

– Dishes and cutlery must not impede the

rotation of the spray arms.

– Load hollow items such as cups,

glasses, pans, etc. with the opening

downwards so that water cannot collect

in the container or a deep base.

– Dishes and items of cutlery must not lie

inside one another, or cover each other.

– To avoid damage to glasses, they must

not touch.

– Lay small objects in the cutlery basket.

• Plastic items and pans with non stick coat-

ings have a tendency to retain water

drops; these items will not dry as well as

porcelain and steel items.

• Light items (plastic bowls etc.) must be

loaded in the upper basket and arranged

so they do not move.

For washing in the dishwasher the following cutlery and dishes

are not suitable: are of limited suitability:

• Cutlery with wooden, horn, china or mother-of-

pearls handles.

• Plastic items that are not heat resistant.

• Older cutlery with glued parts that are not tem-

perature resistant.

• Bonded cutlery items or dishes.

• Pewter or copper items.

• Lead crystal glass.

• Steel items prone to rusting.

• Wooden platters.

• Items made from synthetics fibres.

• Only wash stoneware in the dishwasher if it is

specially marked as being dishwasher-safe by

the manufacturer.

• Glazed patterns may fade if machine washed

frequently.

• Silver and aluminium parts have a tendency to

discolour during washing: Residues, e.g. egg

white, egg yolk and mustard often cause dis-

colouring and staining on silver. Therefore al-

ways clean left-overs from silver immediately, if

it is not to be washed straight after use.

Load cutlery and dishes

The lower basket

The lower basket is designed to take sauce-

pan, lids, plates, salad bowls, cutlery etc.

Service dishes and large lids should be ar-

ranged around the edge of the basket, en-

suring that the spray arms can turn freely.

electrolux 9

The rows of prongs in the lower basket can

lie flat to allow you to load pots, pans and

bowls.

The cutlery basket

Long bladed knives stored in an upright

position are a potential hazard. Long

and/or sharp items of cutlery such as

carving knives must be positioned

horizontally in the upper basket. Take

care when loading or unloading sharp

items such as knives.

Forks and spoons should be placed in the

removable cutlery basket with the handles

facing downwards and the knives with their

handles facing upwards.

If the handles protrude from the bottom of the

basket, obstructing the lower spray arm, load

the cutlery with the handles facing upwards.

Mix spoons with other cutlery to prevent

them from sticking together.

To make loading of the cutlery basket easier,

lower the cutlery basket handle.

For best results we recommend that you use

the cutlery grids.

If the size and dimensions of the cutlery do

not allow the use of the grids, they can be

easily hidden.

10 electrolux

The cutlery basket is in two parts which can

be separated to give greater loading flexibili-

ty. To separate the two parts, slide them hor-

izontally in opposite directions and pull them

apart.

To reassemble, reverse the procedure.

The upper basket

The upper basket is designed for saucers,

salad bowls, cups, glasses, pots and lids.

Arrange items on and underneath the cup

racks so that water can reach all surfaces.

Glasses with long stems can be placed up-

side down in the cup racks.

For taller items, the cup racks can be folded

upwards.

Before closing the door, ensured that

the spray arms can rotate freely.

Adjusting the height of the upper basket

If washing very large plates you can load

them in the lower basket after moving the

upper basket to the higher position.

Maximum height of the dishes in the lower

basket

With upper basket

raised

31 cm

With upper basket

lowered

27 cm

To move to the higher position proceed

as follows:

1. Pull out the basket until it stops.

2. Carefully lift both sides upwards until the

mechanism is engaged and the basket is

stable.

electrolux 11

To lower the basket to the original posi-

tion proceed as follows:

1. Pull out the basket until it stops.

2. Carefully lift both sides upwards and then

allow the mechanism to drop back down

slowly, keeping hold of it.

Never lift or lower the basket on one side

only

When the basket is in the higher position

cups cannot be placed on the cup racks.

After loading your machine always

close the door, as an open door can

be a hazard.

Use of detergent

Only use detergents specifically de-

signed for use in dishwashers.

Please observe the manufacturer’s dos-

ing and storage recommendations as

stated on the detergent packaging.

Using no more than the correct amount

of detergent contributes to reducing pol-

lution.

Fill with detergent

1. Open the lid.

2. Fill the detergent dispenser (1) with de-

tergent. The marking indicates the dosing

levels:

20 = approximately 20 g of detergent

30 = approximately 30 g of detergent.

3. All programmes with prewash need an

additional detergent dose (5/10 g) that

must be placed in the prewash detergent

chamber (2).

This detergent will be used during the

prewash phase.

When using detergent tablets; place the

tablet in compartment (1)

1

2

12 electrolux

4. Close the lid and press until it locks in

place.

Detergent tablets from different manu-

facturers dissolve at different rates. For

this reason, some detergent tablets do

not attain their full cleaning power during

short washing programmes. Therefore,

please use long washing programmes

when using detergent tablets, to ensure

the complete removal of detergent re-

siduals.

Multi-tab function

This appliance is equipped with the "Multitab

function", that allows the use of the "Multitab"

combi detergent tablets.

These products are detergents with a com-

bined cleaning, rinsing and salt functions.

They can also contain other different agents

depending on which kind of tablets you

choose ("3 in 1", "4 in 1", "5 in 1" etc...).

Check whether these detergents are suitable

for your water hardness. See the manufac-

turers instructions.

Once this function is selected it will remain

active for all following wash programmes.

With the selection of this function the inflow

of rinse aid and salt from each respective

supply container is automatically deactivated

and also the indicator lights for salt and rinse

aid are deactivated.

When using the "Multitab function", the cycle

durations may change. If this is the case, the

running time for the programme is automat-

ically updated on the digital display.

Activate/deactivate the ''Multitab func-

tion'' before the start of a washing pro-

gramme.

Once the programme is running, the

"Multitab function " can NO longer be

changed. If you want to cancel the "Mul-

titab function " you have to cancel the

programme setting and then deactivate

the ''Multitab function''. In this case you

have to set a washing programme (and

desired options) again.

Activation/deactivation of the Multitab

function

Simultaneously press and hold the two Mul-

titab buttons (function buttons D and E) until

the Multitab indicator light comes on. This

means that the function is active.

To deactivate the function press the same

buttons again until the indicator light corre-

sponding to the Multitab function symbol

goes off.

If the drying results are not satisfac-

tory we suggest that you:

1. Fill up the rinse aid dispenser with

rinse aid.

2. Activate the rinse aid dispenser.

3. Set the rinse aid dosage to position

2.

• The activation/deactivation of the

rinse aid is only possible with the Mul-

titab function active.

Activation/deactivation of the rinse aid

dispenser

1. Press the On/Off button. The dishwasher

must be in setting mode.

2. Simultaneously press and hold function

buttons B and C, until the lights of func-

tion buttons A , B, and C start flashing.

3.

Press function button B, the lights of

function buttons A and C turn off while

the light of function button B continues to

flash. The digital display indicates the cur-

rent setting.

Rinse aid dispenser deactivated

electrolux 13

Rinse aid dispenser activated

4. To change the setting, press button B

again, the digital display shows the new

setting.

5. To memorize the operation, switch off the

dishwasher by pressing the On/Off but-

ton.

If you decide to revert back to the

use of individual detergents we ad-

vise that you:

1. Deactivate the Multitab function.

2. Fill up the salt container and the rinse

aid dispenser again.

3. Adjust the water hardness setting to

the highest setting and perform 1

normal washing programme without

loading any dishes.

4. Adjust the water hardness setting

according to the hardness of the wa-

ter in your area.

5. Adjust the rinse aid dosage.

Select and start a washing programme

Select the washing programme and

delay start with the door slightly

opened. The start of the programme

or the countdown of the delay start

will occur only after the closure of

the door. Until then it is possible to

modify the settings

1. Check that the baskets have been loaded

correctly and that the spray arms are free

to rotate.

2. Check that the water tap is opened.

3. Press the On/Off button. The dishwasher

must be in setting mode.

4. Press the button corresponding to the re-

quired programme (refer to 'Washing

programmes' chart).

Close the dishwasher door, the pro-

gramme starts automatically.

Setting and starting the programme with

delay start

1. After having selected the washing pro-

gramme, press the delay start button until

the flashing number of hours for the delay

start shows in the digital display.

The start of the selected washing pro-

gramme can be delayed for between 1

and 19 hours.

2. Close the dishwasher door, the count-

down starts automatically.

3. The countdown will decrease with steps

of 1 hour.

4. The opening of the door will interrupt the

countdown. Close the door; the count-

down will continue from the point at

which it was interrupted.

5. Once the delay start has elapsed the pro-

gramme will start automatically.

Once the washing programme has star-

ted, a point-shaped optical signal ap-

pears on the floor beneath the dish-

washer door.

This optical signal will remain illuminated

for all the duration of the washing pro-

gramme.

If the appliance has been installed higher

up with a furniture door mounted flush,

the optical signal will be no longer visible.

Warning! Interrupt or cancel a

washing programme in progress

ONLY if it's absolutely necessary.

Attention! Hot steam may escape

when the door is opened. Open the

door carefully.

Interrupt a washing programme in

progress

• Open the dishwasher door; the pro-

gramme will stop. Close the door; the pro-

gramme will start from the point at which

it was interrupted.

Cancel a delay start or a washing

programme in progress

• Simultaneously press and hold the two

function buttons B and C until all the pro-

gramme lights come on.

• Cancelling a delay start will also cancel the

washing programme. You have to select

the washing programme again.

• If a new washing programme is to be se-

lected, check that there is detergent in the

detergent dispenser.

End of the washing programme

• The dishwasher will automatically stop and

an audible signal informs you of the end of

the washing programme.

14 electrolux

• The optical signal on the floor beneath the

dishwasher door goes off.

1. Open the dishwasher door. The digital

display shows zero.

2. Switch of the dishwasher.

3. Leave the dishwasher door ajar for a few

minutes before removing the dishes; this

way they will be cooler and the drying will

be improved.

Unloading the dishwasher

• Hot dishes are sensitive to knocks. The

dishes should therefore be allowed to cool

down before removing from the appliance.

•Empty the lower basket first and then the

upper one; this will avoid water dripping

from the upper basket onto the dishes in

the lower one.

• Water may appear on the sides and the

door of the dishwasher as the stainless

steel will eventually become cooler than

the dishes.

When the washing programme has

finished, it is recommended that the

dishwasher is unplugged and the

water tap turned off.

electrolux 15

Washing programmes

Programme Degree of

soil

Type of load Programme description Consumption

values

1)

Prewash

Main wash

2)

Intermediate rinse

Final rinse

Drying

Duration (in minutes)

3)

Energy (in kWh)

Water (in litres)

Intensive

Heavy soil

Crockery,

cutlery, pots

and pans

70

2

-

1,8 - 2,0

23 - 25

4)

Any

Crockery,

cutlery, pots

and pans

45

-

70

1 - 2

-

1,1 - 1,7

12 - 23

Quick

5)

Normal or

light soil

Crockery and

cutlery

60

-

0,9

9

Normal soil

Crockery and

cutlery

50

-

1,0 - 1,1

12 - 13

Rinse and hold

Any

Partial load (to

be completed

later in the

day). This

programme

does not re-

quire the use

of detergent.

-

0,1

4

1) The consumption values are intended as a guide. They depend on pressure and the temperature of

the water, variations of the power supply and the quantity of dishes.

2) Temperature of the main wash in Celsius scale.

3) The digital display shows the programme duration.

4) During the 'Auto' washing programme the level of soil on the dishes is given by how cloudy the water

is. The programme duration, water and energy consumption levels can change. Causes that can

change the consumption values are: if the baskets are fully or partially loaded, degree of soil of the

dishes. The temperature of the water is automatically adjusted between 45° C and 70° °C.

5) Programme for washing a not fully loaded dishwasher. Daily programme, made to meet the needs of

a family who wants to load breakfast and dinner crockery and cutlery.

Care and cleaning

Cleaning the filters

The filters must be checked and cleaned

from time to time. Dirty filters will degrade the

washing result.

Warning! Before cleaning the filters

ensure that the machine is switched off.

1. Open the door, remove the lower basket.

2. The dishwasher filter system comprises a

coarse filter (A), a microfilter (B) and a flat

filter. Unlock the filter system using the

handle on the microfilter.

16 electrolux

3. Turn the handle about 1/4 a turn anti-

clockwise and remove the filter system

4. Take hold of the coarse filter (A) by the

handle with the hole and remove from the

microfilter (B).

5. Clean all filters thoroughly under running

water.

6. Remove the flat filter from the base of the

washing compartment and clean both

faces thoroughly.

7. Put the flat filter back in the base of the

washing compartment and ensure that it

fits perfectly.

8.

Place the coarse filter (A) in the microfilter

(B) and press together.

9. Put the filter combination in place and

lock by turning the handle clockwise to

the stop. During this process ensure that

the flat filter does not protrude above the

base of the washing compartment.

NEVER use the dishwasher without

filters. Incorrect repositioning and

fitting of the filters will produce poor

washing results and will result in

damage to the appliance.

NEVER try to remove the spray

arms.

If residues of soil have clogged the holes

in the spray arms, remove the debris

with a cocktail stick.

External cleaning

Clean the external surfaces of the machine

and control panel with a damp soft cloth. If

necessary use only neutral detergents. Never

use abrasive products, scouring pads or sol-

vent (acetone, trichloroethylene etc...).

Internal cleaning

Ensure that the seals around the door, the

detergent and rinse aid dispensers are

cleaned regularly with a damp cloth.

We recommend every 3 months you run the

wash programme for heavy soiled dishes us-

ing detergent but without dishes.

Prolonged periods of non-operation

If you are not using the machine for a pro-

longed period of time you are advised to:

1. Unplug the appliance and then turn off

the water.

2. Leave the door ajar to prevent the forma-

tion of any unpleasant smells.

3. Leave the inside of the machine clean.

Frost precautions

Avoid placing the machine in a location

where the temperature is below 0°C. If this is

unavoidable, empty the machine, close the

appliance door, disconnect the water inlet

pipe and empty it.

Moving the machine

If you have to move the machine (moving

house etc...):

1. Unplug it.

2. Turn the water tap off.

3. Remove the water inlet and discharge

hoses.

4. Pull the machine out together with the

hoses.

electrolux 17

Avoid over tilting the machine during trans-

portation.

What to do if…

The dishwasher will not start or stops during

operation.

Certain problems can be due to the lack of

simple maintenance or oversights, which can

be solved with the help of the hints described

in the chart, without calling out an engineer.

Open the door, switch off the dishwasher

and carry out the following suggested cor-

rective actions.

Fault codes and malfunction Possible cause and solution

• continuous flashing of the running programme

light

• point-shaped optical signal is flashing

• intermittent audible signal

•

appears in the digital display

The dishwasher does not fill with water

• The water tap is blocked or furred with lime-

scale.

Clean the water tap.

• The water tap is turned off.

Turn the water tap on.

• The filter (where present) in the threaded hose

fitting at the water inlet valve is blocked.

Clean the filter in the threaded hose.

• The water inlet hose has not been correctly laid

or it is kinked or squashed.

Check the water inlet hose connection.

• continuous flashing of the running programme

light

• point-shaped optical signal is flashing

• intermittent audible signal

•

appears in the digital display

The dishwasher will not drain

• The sink spigot is blocked.

Clean out the sink spigot.

• The water drain hose has not been correctly laid

or it is kinked or squashed.

Check the water drain hose connection.

• continuous flashing of the running programme

light

• point-shaped optical signal is flashing

• intermittent audible signal

•

appears in the digital display

Anti-flood device is activated

• Close the water tap and contact your local

Service Force Centre.

The flashing of the point-shaped optical

signal on the floor beneath the dish-

washer door will not be visible if the ap-

pliance has been installed higher up with

a furniture door mounted flush.

Malfunction Possible cause and solution

The programme does not start • The dishwasher door has not been properly

closed.

Close the door.

• The main plug is not plugged in.

Insert the main plug

• The fuse has blown out in the household fuse

box.

Replace the fuse.

• Delay start has been set.

If dishes are to be washed immediately, cancel

the delay start.

Once these checks have been carried out

switch on the appliance and close the door.

The programme will continue from the point

at which it was interrupted.

If the malfunction or fault code reappears

contact your local Service Force Centre.

18 electrolux

For other fault codes not described in the

above chart, please contact your local Serv-

ice Force Centre.

Contact your local Service Force Centre,

quoting the model (Mod.), product number

(PNC) and serial number (S.N.).

This information can be found on the rating

plate located on the side of the dishwasher

door.

So that you always have these numbers at

hand, we recommend you to make a note of

them here:

Mod. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PNC : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

S.N. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The wash results are not satisfactory

The dishes are not

clean

• The wrong programme has been selected.

• The dishes are arranged in such a way as to stop water reaching all parts

of a surface. The baskets must not be overloaded.

• The spray arms do not rotate freely due to incorrect arrangement of the

load.

• The filters in the base of the washing compartment are dirty or incorrectly

positioned.

• Too little or no detergent has been used.

• Where there are limescales deposits on the dishes; the salt container is

empty or incorrect level of the water softener has been set.

• The drain hose connection is not correct.

• The salt container cap is not properly closed.

The dishes are wet

and dull

• Rinse aid was not used.

• The rinse aid dispenser is empty.

There are streaks,

milky spots or a blu-

ish coating on

glasses and dishes

• Decrease rinse aid dosage.

Water drops have

dried onto glasses

and dishes

• Increase rinse aid dosage.

• The detergent may be the cause. Contact the detergent manufacturer con-

sumer care line.

If after all these checks, the problem persists,

contact your local Service Force Centre.

Technical data

Dimensions Width

Height

Depth

59,6 cm

81,8 - 87,8 cm

55,5 cm

Electrical connection - Voltage -

Overall power - Fuse

Information on the electrical connection is given on the rating plate

on the inner edge of the dishwasher door.

Water supply pressure Minimum

Maximum

0,05 MPa (0,5 bar)

0,8 MPa (8 bar)

Capacity 12 place settings

Hints for test institutes

Testing in accordance with EN 60704 must

be carried out with appliance fully loaded and

using the test programme (refer to 'Washing

programmes').

Test in accordance with EN 50242 must be

carried out when the salt container and rinse

aid dispenser have been filled with salt and

rinse aid respectively and using the test pro-

gramme (refer to 'Washing programmes').

electrolux 19

Full load: 12 standard place settings

Amount of detergent required: 5 g + 25 g (Type B)

Rinse aid setting position 4 (Type III)

Arrangement upper basket

Arrangement lower basket

Arrangement cutlery basket

Installation

Warning! Any electrical and/or

plumbing work required to install

this appliance should be carried out

by a qualified electrician and/or

plumber or competent person.

Remove all packaging before positioning the

machine.

If possible, position the machine next to a

water tap and a drain.

This dishwasher is designed to be fitted un-

der a kitchen counter or work surface.

Attention! Carefully follow the instructions

on the enclosed template for building in the

dishwasher and fitting the furniture panel.

No further openings for the venting of the

dishwasher are required, but only to let the

water fill and drain hose and power supply

cable pass through.

The dishwasher incorporates adjustable feet

to allow the adjustment of the height.

During all operations that involve accessibility

to internal components the dishwasher has

to be unplugged.

When inserting the machine, ensure that the

water inlet hose, the drain hose and the sup-

ply cable are not kinked or squashed.

Fixing to the adjacent units

The dishwasher must be secured against tilt-

ing.

20 electrolux

Страница загружается...

Electrolux ESL66010 Руководство пользователя

Похожие модели бренда

Модели других брендов