1
GB
FM Stereo
FM-AM Tuner
© 1998 by Sony Corporation
3-865-570-31(1)
Operating instructions
Instrukcja obsługi
Инструкция по эксплуатации
GB
PL
RU
ST-SE500
2
GB
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open
the cabinet. Refer servicing to qualified
personnel only.
Precautions
On safety
• Should any liquid or solid object fall
into the unit, unplug the unit and
have the unit checked by qualified
personnel before operating it any
further.
On power sources
• Before operating the unit, be sure that
the operating voltage of your unit is
identical with that of your local
power supply.
• Unplug the unit from the wall outlet
if it is not to be used for an extended
period of time. To disconnect the
cord, pull it out by grasping the plug.
Never pull the cord itself.
• AC power cord must be changed only
at the qualified service shop.
On placement
• Place the unit in a location with
adequate ventilation to prevent heat
buildup and prolong the life of its
components.
• Do not place the unit near heat
sources, or in a place subject to direct
sunlight, excessive dust or
mechanical shock.
• Do not place anything on top of the
cabinet which might block the
ventilation holes and cause
malfunctions.
• Do not install the appliance in a
confined space, such as a bookcase or
built-in cabinet.
On cleaning the cabinet
• Clean the cabinet, panels and controls
with a soft cloth lightly moistened
with a mild detergent solution. Do
not use any type of abrasive pad,
scouring powder or solvent such as
alcohol or benzine.
On repacking
• Do not throw away the carton and the
packing material. This makes an
ideal container when transporting the
unit. When shipping the unit, repack
it as it was packed at the factory.
If you have any question or problem
concerning your unit that is not covered
in this manual, please consult your
nearest Sony dealer.
3
GB
TABLE OF CONTENTS
Getting Started
Unpacking 4
Hooking up the System 4
Selecting the German Display 6
Storing FM Stations Automatically (Auto-betical select) 6
Basic Operations
Receiving Preset Stations 7
Advanced Tuner Operations
About the Menu Entry System 8
Customizing the Display 8
Receiving Broadcasts 9
Tips for Better FM Reception 10
Presetting Radio Stations 10
Naming the Preset Stations 11
Organizing the Preset Stations 12
Using the Radio Data System (RDS) 13
Additional Information
Troubleshooting 15
Specifications 15
Index 16
GB
Welcome!
Thank you for purchasing the Sony FM
Stereo FM/AM Tuner. Before operating
the unit, please read this manual
thoroughly and retain it for future
reference.
Convention
The following icon is used in this
manual:
Indicates hints and tips for
making the task easier.
4
GB
Unpacking
Check that you received the following items with the
tuner:
• Audio cord (1)
• AM loop aerial (1)
• FM wire aerial (1)
• EON connecting cord (1)
Getting Started
around the frame of the aerial. Be careful to
unwrap only the braided section of the lead wire.
Do not unwrap more than 3 lengths of the lead
wire. Also, be careful not to unbraid the lead wire.
3 Assemble the supplied aerial as shown below.
4 Connect the AM loop aerial to the AM terminals
on the back of this unit.
5 Adjust the aerial direction for the best reception.
The AM loop aerial has a directivity which detects
the signal from some angles more strongly than
others. Set the aerial to the orientation which
provides the best receiving condition.
If a high pitched noise (beat noise) occurs when
recording AM broadcasts, adjust the position of
the AM loop aerial so that the noise disappears.
If you live in a building constructed of reinforced
concrete, or with a steel frame, you may not be
able to achieve good reception since the radio
waves become weaker indoors. In this case, we
recommend connecting an optional aerial such as
the Sony AN-1.
For stations that are difficult to receive
Try repositioning the loop aerial while tuning. Placing
the supplied AM loop aerial near a window will help
improve reception quality.
Hooking up the System
Before you get started
• Turn off the power to all components before making
any connections.
• Do not connect the mains lead until all of the
connections are completed.
• Be sure to make connections firmly to avoid hum and
noise.
• When connecting an audio cord, be sure to match the
colour-coded pins to the appropriate jacks: White
(left) to White; and Red (right) to Red.
AM aerial hookups
This section describes how to connect the supplied AM
loop aerial. For the specific location of the AM
ANTENNA terminals, see the illustration below.
What will I need?
• AM loop aerial (supplied) (1)
1 Before assembling the supplied aerial, pull the
lead wire out from the slot in the aerial frame.
2 Unwrap 3 lengths of the braided lead wire from
AM loop aerial
ANTENNA
FM
75 COAXIAL
AM
y
AM ANTENNA
5
GB
FM aerial hookups
With an FM outdoor aerial, you can obtain a higher FM
broadcast sound quality. We recommend that you use
the supplied FM wire aerial only temporarily until you
install an FM outdoor aerial. For the specific location of
the FM ANTENNA terminal, see the illustration below.
What will I need?
• FM wire aerial (supplied) (1)
• FM outdoor aerial (not supplied) (1) and 75-ohm coaxial
cable with IEC female type connector (not supplied) (1)
Connect the supplied FM wire aerial or an FM outdoor
aerial (not supplied) to one of the FM terminals on the
back of this unit.
Connecting a ground wire
If you connect an outdoor aerial, be sure to connect a
earth lead (not supplied) to the AM ANTENNA y
terminal (in addition to the AM loop aerial) for
lightning protection.
Getting Started
FM ANTENNA
IEC female type connector
Amplifier hookups
Connect the tuner to an amplifier. Be sure to turn off
the power to both components before connection. For
the specific location of the terminals, see the illustration
below.
What cables will I need?
• Audio cord (supplied) (1)
Connect the white plugs to the white (L) jacks and the red
plugs to the red (R) jacks. Insert the plugs completely into
the jacks; incomplete connections may cause noise.
EON CONTROL
Red (R)
White (L)White (L)
Red (R)
TUNER IN
RL
RL
LINE OUT
Amplifier
Tuner
If you have a Sony amplifier equipped with an EON
CONTROL IN terminal
Use the supplied EON connecting cord to connect the
EON CONTROL OUT terminal on the tuner to the EON
CONTROL IN terminal on your amplifier. This lets you
use the EON function (see page 13) when listening to
other components.
Mains lead hookup
Connect the mains lead to a wall outlet after completing all
of the previous connections.
Amplifier
Tuner
EON CONTROL
OUT
EON CONTROL
IN
/
ANTENNA
FM
75 COAXIAL
AM
y
FM wire aerial
ANTENNA
FM
75 COAXIAL
AM
y
FM outdoor aerial
IEC female type
connector
LINE OUT
to a wall
outlet
6
GB
Storing FM Stations
Automatically
(Auto-betical select)
With “Auto-betical select” you can automatically store
up to 30 FM and FM RDS stations in alphabetical order
without redundancy. Additionally, “Auto-betical
select” only stores the stations with the clearest signals.
If you want to store FM or AM (MW and LW) stations
one by one, see “Receiving Broadcasts” on page 9 and
“Presetting Radio Stations” on page 10.
1 Press POWER to turn on the tuner.
2 Turn on the amplifier and select the TUNER
mode.
3 Press AUTO-BETICAL SELECT.
“Yes” and “No” appear in the display.
4 Turn TUNING/SELECT to select “Yes”.
5 Press AUTO-BETICAL SELECT again.
The tuner scans and stores all the FM and FM
RDS stations in the broadcast area.
For RDS stations, the tuner first checks for
stations broadcasting the same programme, then
stores only the one with the clearest signal. The
selected RDS stations are sorted alphabetically by
their Programme Service name, then assigned a
two-character preset code. For more details on
RDS, see page 13.
Regular FM stations are assigned two-character
preset codes and stored after the RDS stations.
To change the location of, or erase, a preset station
See “Organizing the Preset Stations” on page 12.
Notes
• If you move to another area, repeat this procedure to store
stations in your new area.
• For details on tuning stored stations, see page 7.
• The FM MODE setting is also stored along with the
station.
• If you move the aerial after storing stations using "Auto-
betical select," the stored settings may no longer be valid.
If this happens, store the stations again.
Getting Started
Selecting the German Display
You can choose either an English or a German
language display. The factory preset language is
English. To change the display to German, follow the
steps below.
1 Press POWER to turn off the tuner.
2 While holding down the “2” button, press
POWER to turn on the tuner .
“Deutsch” appears in the display.
To return to the English display
Repeat this procedure.
“English” appears in the display.
POWER
AUTO-BETICAL SELECT
TUNING/SELECT
POWER
2
7
GB
Make sure you’ve hooked up the tuner and preset stations.
(See pages 4 - 5 for hookups and page 6 or 10 for presetting.)
Turn on the amplifier and select the TUNER mode.
Press POWER to turn on the tuner.
Press SHIFT to select A, B, or C.
Press the preset number you want (1 - 0).
Receiving Preset Stations
This section shows you how to receive preset stations.
To check broadcasts by scanning the preset stations
5
3
2
1
4
• To tune in a non-preset
station, see “Receiving
Broadcasts” on page 9.
Basic Operations
POWER
S
EON Link System
AUTO-BETICAL
SELECT
MEMORY FM MODE BAND
TA NEWS/INFO PTY DISPLAY
EON
SHIFT 1 2 3 4 5 6 7 8 9 0 DIRECT
MENU RETURN
CHARACTER TUNE MODE
TUNING/ SELECT
ENTER
FM STEREO/FM-AM TUNER ST-SE500
3
45
1Press TUNE MODE repeatedly so that “PRESET” appears in the display.
2 Turn TUNING/SELECT.
Each time you turn TUNING/SELECT, a preset station is received and
the settings (preset code, frequency, and station name, etc.) appear in the
display. The signal meter indicates the strength of the broadcast signal.
0 DIRECT
MENU RETURN
CHARACTER TUNE MODE
TUNING/ SELECT
ENTER
FM STEREO/FM-AM TUNER ST-SE5 00
TUNING/SELECT
TUNE MODE
8
GB
About the Menu Entry System
This tuner uses a menu entry system which allows you
to operate various functions by following messages on
the display. Use the following controls for menu
operation.
Advanced Tuner Operations
TUNING/SELECT
ENTER
MENU
RETURN
Use the
MENU button
TUNING/SELECT knob
ENTER button
RETURN button
To:
enter the menu mode.
display different items or
settings.
select the currently displayed
item or setting.
return to a previous stage in the
menu mode.
Customizing the Display
You can choose the appearance of the display from one
of the following four display modes.
1 Press MENU, then turn TUNING/SELECT until
“Disp-Mode” appears in the display.
2 Press ENTER.
“Select” appears in the display.
3 Turn TUNING/SELECT to select a display mode.
Full Display/Full Brightness
.
Full Display/Dimmed
.
Minimal Display/Full Brightness
.
Minimal Display/Dimmed
4 Press ENTER.
The setting remains in effect until you change it
again.
If you press one of the buttons on the main unit,
the minimal display changes to the full display
with the selected brightness. After about 4
seconds, the display returns to the display mode
you selected.
TUNING/SELECT
ENTER
MENU
9
GB
Receiving Broadcasts
This tuner lets you enter a station’s frequency directly
by using the numeric buttons (direct tuning). If you
don’t know the frequency of the station you want, see
“Receiving broadcasts by scanning stations (Automatic
tuning)”.
Before you begin, make sure you have:
• Connected an FM/AM aerial to the tuner as
indicated on page 4.
1 Press BAND to select FM, MW, or LW.
2 Press DIRECT.
3 Press the numeric buttons to enter the frequency.
Example 1: FM 102.50 MHz Example 2: AM 1350 kHz
To receive other stations
Repeat Steps 1 to 3.
When you tune in AM (MW and LW) stations
Adjust the direction of the AM loop aerial for optimum
reception.
If the STEREO indicator remains off
Press FM MODE when an FM stereo broadcast is
received.
If an FM stereo programme is distorted
The STEREO indicator flashes. Press FM MODE to
change to monaural (MONO). You will not have the
stereo effect but the distortion will be reduced. To
return to stereo mode, press this button again.
If you cannot tune in a station and the entered
numbers are flashing
Make sure you’ve entered the right frequency. If not,
press DIRECT and reenter the frequency you want.
If the entered numbers still flash, the frequency is not
used in your area.
If you enter a frequency not covered by the tuning
interval
The entered value is automatically rounded up or down
to the closest covered value.
Tuning intervals for direct tuning are:
FM: 50 kHz intervals
AM: 9 kHz intervals (MW), 1 kHz interval (LW)
Receiving broadcasts by scanning stations
(Automatic tuning)
With automatic tuning you can quickly tune in a
station without having to know its frequency.
1 Press BAND to choose either FM, MW, or LW.
2 Press TUNE MODE so that “AUTO TUNING”
appears in the display.
3 Turn TUNING/SELECT slightly and release it
when the frequency numbers start changing.
Turn the knob to the right for a higher frequency;
turn it to the left for a lower frequency.
When the tuner locates a station, it stops
automatically, “TUNED” appears in the display.
The signal meter indicates the strength of the
broadcast signal.
4 Repeat step 3 until you tune in the appropriate
station.
To store the station, see “Presetting Radio
Stations” on page 10.
If you cannot tune in the station you want(Manual
Tuning)
With manual tuning you can search through all stations
broadcasting on each band, and tune in stations with
extremely weak signals that you might not be able to
receive with automatic tuning.
1 Press BAND repeatedly to choose FM, MW, or LW.
2 Press TUNE MODE so that only “TUNING” appears
in the display. “AUTO” should not appear in the
display.
3 Turn TUNING/SELECT until you tune in the desired
station.
Turn the knob to the right for a higher frequency;
turn it to the left for a lower frequency.
The signal meter indicates the strength of the
broadcast signal.
Note
When you reach the highest or lowest frequency of any
band, tuning stops.
Advanced Tuner Operations
Numeric
buttons
BAND DIRECT
1 0250
1350
10
GB
Advanced Tuner Operations
Presetting Radio Stations
This section shows you how to store up to 30 of your
favorite FM or AM (MW and LW) stations manually
onto preset codes made up of characters (A, B, or C)
and numbers (1-0), such as A7. You can store up to 10
stations on each of the 3 different letters. You can use
these letters to classify stations according to music
category or station band.
1 Tune in the FM, MW, or LW station you wish to
store.
2 Press MEMORY.
“MEMORY” appears along with the lowest
vacant code to indicate that the tuner is ready to
store the station.
3 Press SHIFT to chose either A, B, or C.
The letter you choose appears in the display.
4 Press a numeric button (1-0).
The tuner stores the station at the preset code you
specified.
5 Repeat steps 1 through 4 to store other stations.
RDS Station names are stored automatically
When you preset an RDS station broadcasting station
name information, the station name is automatically
stored at the station preset.
If you want to label the stations
Follow the procedure described in “Naming Preset
Stations” on page 11.
Numeric
buttons
MEMORY SHIFT
Tips for Better FM Reception
This tuner has two functions designed for better
reception, the FM mode setting and the digital signal
meter. First, try to receive stations with the standard
settings. If the reception is not good, try altering the
reception quality to obtain a clear signal. The tuner
stores the FM mode setting, together with the
frequency when you make a station preset.
Setting the FM mode
Press FM MODE a few times to choose the reception
mode, select either Auto stereo (no indication) or
MONO.
• Auto stereo mode receives stereo broadcasts with
strong signals. Press FM MODE a few times so that
“MONO” disappears.
• “MONO” receives stations with weak signals.
Stations will be received in monaural but with even
less noise.
Checking the signal strength
You can use the digital signal meter to check the signal
strength of FM frequencies. The display range is from
16 to 70 dB (1µV of radio frequency voltage = 0dB). To
obtain a signal to noise ratio sufficient for receiving a
stereo broadcast, we recommend a reading greater
than 50 dB. (You can also change the FM MODE while
using the signal meter to determine the best reception.)
1 Tune in an FM station.
2 Press DISPLAY repeatedly to display the digital
signal meter.
3 Rotate the FM aerial to obtain the strongest signal.
DISPLAY
FM MODE
11
GB
Advanced Tuner Operations
Naming the Preset Stations
You can assign a name up to 13 characters long to each
preset station except FM RDS stations. When the
station is tuned in, the station name will appear instead
of the frequency.
1 Press CHAR.
The cursor blinks in the display.
2 Turn TUNING/SELECT to select a character.
3 When the character you want appears, press
CHAR to move the cursor into position for the
next character.
If you make a mistake
Press CHAR repeatedly until the character you want to
change flashes (every time you press CHAR, the next
character flashes). Then turn TUNING/SELECT to
select a new character.
4 Repeat steps 2 and 3 until the station name you
desire appears in the display.
5 Press MEMORY.
“MEMORY” appears along with the lowest
vacant code to indicate that the tuner is ready to
store the station.
6 Press SHIFT and one of the preset buttons to
specify the preset where you want to store the
station name.
Note
The display returns to normal display mode if you stop
assigning names for more than 8 seconds. If this happens,
start again from the beginning.
To see the frequency of the displayed station name
Press DISPLAY repeatedly.
Numeric
buttons
MEMORY SHIFT
DISPLAY
CHAR TUNING/SELECT
12
GB
Moving preset station
You can also move a specific preset station.
1 Follow steps 1 through 3 in “Organizing the
Preset Stations” and choose “Move” from the Edit
menu, then press ENTER.
2 Turn TUNING/SELECT so that the preset code
you want to move appears in the display and
press ENTER.
3 Turn TUNING/SELECT to select the new location
for the preset code and press ENTER.
The preset station you selected is moved to the
new location and the other preset stations in that
group (“A” for example) shift backwards to make
room for the new preset.
EXAMPLE:
If you move A4 to A1.
Erasing preset stations
You can erase preset stations one by one.
1 Follow steps 1 through 3 in “Organizing the
Preset Stations” and choose “Erase” from the Edit
menu, then press ENTER.
2 Turn TUNING/SELECT so that the preset code
you want to erase appears in the display and
press ENTER.
The preset station you selected is erased from the
preset memory and the other preset stations in
that group (“A” for example) shift forward to fill
in the blank space.
EXAMPLE:
If you erase A1.
If you want to erase all the preset stations
1 Turn off the power
2 While holding down the number 5 button and
AUTO-BETICAL SELECT, press POWER to turn on
the power.
Advanced Tuner Operations
89.5 94.5 96.5 98.0 100.5 103.0 104.5 106.0Frequency
A1 A2 A3 A4 A5 A6 A7 A8Preset
.
98.0 89.5 94.5 96.5 100.5 103.0 104.5 106.0Frequency
A1 A2 A3 A4 A5 A6 A7 A8Preset
89.5 94.5 96.5 98.0 100.5 103.0 104.5 106.0Frequency
A1 A2 A3 A4 A5 A6 A7 A8Preset
94.5 96.5 98.0 100.5 103.0 104.5 106.0Frequency
A1 A2 A3 A4 A5 A6 A7 A8Preset
.
To
change the location of a specific preset (see
below).
erase a specific preset (see below).
sort preset stations in alphabetical order
according to their preset names.
Stations without preset names are arranged
by frequency, from low to high.
sort preset stations in order of their signal
strength (FM stations only).
MW and LW frequencies are arranged by
frequency.
sort FM RDS stations with PI information
alphabetically by country.
Other stations are arranged by frequency.
sort preset stations in order of their
frequency band (FM - MW - LW).
TUNING/SELECT
ENTER
MENU
Choose
Move
Erase
Alphabet
Strength
Country
Band
Organizing the Preset Stations
This tuner makes it easy to arrange preset stations in
the order you prefer. You can arrange all the preset
stations automatically, according to alphabetical order,
signal strength, country code, or tuner band, or you
can use the “Move” and “Erase” functions to move and
erase specific preset stations.
1 Press MENU.
2 Turn TUNING/SELECT until “Edit” appears in
the display and press ENTER.
If no stations have been stored as presets, “No
Preset” appears in the display.
3 Turn TUNING/SELECT to choose one of the
following sorting methods:
4 Press ENTER.
The tuner sorts the stations, then returns to
normal tuning mode and receives preset station
A1.
Note
Some countries use the same country code, and the stations
from these counties may be arranged together.
13
GB
Notes
• If there is an emergency announcement by governmental
authorities, “ALARM” flashes in the display.
• If a station is not providing a particular RDS service,
“NO...” (such as “NO PTY”) appears in the display.
• When a station broadcasts radio text data, the display
shows the data at the rate it is sent from the station. The
display speed changes in relation to the speed at which
the data is sent.
Monitoring traffic, news, or information
programmes (EON)
Enhanced Other Networks (EON) allows the tuner to
automatically switch to a station broadcasting traffic,
news, or information. After the programme ends, the
tuner switches back to the station you were listening
to. To use this function, be sure to store the stations
beforehand.
To monitor traffic programmes
1 Tune to a preset FM RDS station so that the RDS
TP, or RDS TP EON indicators light in the
display.
2 Press TA so that “TA” appears in the display.
Each time you press TA, the display changes as
follows:
TA (Traffic Announcement) , OFF
When the tuner automatically tunes in a traffic
programme, the TA indicator flashes. If you do
not want to listen to the entire programme, press
TA to switch back to the original station.
To monitor news and/or information programmes
1 Tune to a preset FM RDS station so that the RDS
TP or RDS TP EON indicators light in the display.
2 Press NEWS/INFO so that either the NEWS or
INFO indicator, or both the NEWS and INFO
indicators, appear in the display.
Each time you press NEWS/INFO, the display
changes as follows:
/ NEWS / INFO / NEWS/INFO / OFF
When the tuner automatically tunes in a news or
information programme, the respective indicator
flashes. If you do not want to listen to the entire
programme, press NEWS/INFO to switch back to
the original station.
Using the Radio Data System
(RDS)
What you can do with RDS
The Radio Data System (RDS) is a broadcasting service
that allows radio stations to send additional
information along with the regular radio programme
signal. This tuner offers you three convenient RDS
features: Displaying the RDS information; Monitoring
of traffic, news, or information programmes; and
Locating a station by programme type. RDS is
available only on FM stations.*
Note
RDS may not work properly if the station you are tuned to is
not transmitting the RDS signal properly or if the signal
strength is weak.
* Not all FM stations provide RDS service, nor do they
provide the same types of services. If you are not familiar
with the RDS system, check with your local radio stations
for details on RDS services in your area.
Receiving RDS broadcasts
Simply select a station from the FM band.
When you tune in a station that provides RDS services,
the RDS indicator and the station name appears in the
display.
Displaying the RDS information
Press DISPLAY repeatedly until the information you
desire is displayed.
* This information also appears for non-RDS FM stations.
Advanced Tuner Operations
You can:
Locate each station by name
(e.g., WDR) instead of
frequency.
Locate each station by
frequency.
Display the current time.
Locate a specific type of
programme being broadcast.
(See page 14 for the types of
programmes you can select.)
Display the text messages sent
by the RDS station.
Determine each broadcast's
country of origin.
(See page 10 for details.)
Information displayed
Station Name*
Frequency*
Clock Time
(24 hour system)
Programme Type
Radio Text
Programme Identification
Digital signal meter*
(continued)
14
GB
To stop monitoring the programme
Press TA or NEWS/INFO while the tuner is in the respective
EON standby mode and the indicator goes out.
Notes
• If you tune in an AM (MW/LW) station or an FM station
which does not provide the RDS service, the selected
indicator (TA, NEWS, INFO, or NEWS/INFO) goes off
and the tuner does not standby for EON stations.
• “Weak Signal” appears when the selected station has a
weak signal. “Return” appears when the tuner is trying to
retune a station with a weak signal.
• Turn off the EON feature when you want to record a
programme without interruptions, especially when you
want to do timer recording.
• “No EON” appears in the display if you select an EON
programme before tuning to an RDS station.
• If you make EON CONTROL connections to a compatible
Sony amplifier, the amplifier automatically switches the
function mode to TUNER whenever the tuner receives a
programme you are monitoring.
Locating traffic programmes (TA search)
You can have the tuner locate stations currently
broadcasting traffic programme from among the RDS
stations stored in the tuner's preset memory.
1 Press MENU.
2 Turn TUNING/SELECT until “Traffic” appears in
the display and press ENTER.
The unit enters search mode (“Search” and
“Traffic” appear alternately in the display).
When the tuner finds a traffic announcement, it
stops searching. The tuner receives each station
for 8 seconds.
3 Press ENTER when the tuner receives the station
you desire to listen to that programme.
Locating a station by programme type
(PTY)
You can locate a station you want by selecting a
programme type. The tuner tunes in the type of
programmes currently being broadcast from the RDS
stations stored in the tuner's preset memory.
1 Press PTY.
2 Rotate TUNING/SELECT to select the
programme type you want. See the following
table for the programme types you can select.
Advanced Tuner Operations
3 Press PTY.
The tuner starts searching the preset RDS stations
for the programme (“Search” and the programme
type are displayed alternately).
When the tuner finds the programme you are
looking for, it stops searching. The preset stations
currently broadcasting the selected programme
type are indicated and the tuner receives each
station for 8 seconds.
4 Press PTY when the tuner receives the station you
desire to listen to that programme.
What you hear
Topical programmes that expand on
current news
Emergency broadcasts
Programmes about national or regional
culture, such as religion, language, and
societal concerns
Radio plays and serials
Educational programmes, such as a
“how-to” programme and advice
Programmes about consumer affairs,
medical advice, and weather
Classical music, such as instrumental,
vocal, and choral works
Easy Listening (middle of the road music)
News programmes
Music that does not fit into any of the
above categories, such as jazz and
rhythm and blues
Popular music programmes
Any programmes not defined above
Rock music programmes
Programmes about the natural sciences
and technology
Sports programmes
Performances of major orchestras,
chamber music, opera, etc.
Other types of programmes such as,
celebrity interviews, panel games, and
comedy
Programme
type
Affairs
Alarm
Culture
Drama
Education
Information
L. Classical
M.O.R.Music
News
Other Music
Pop Music
PTY
undefined
Rock Music
Science
Sports
S. Classical
Varied
15
GB
Troubleshooting
If you experience any of the
following difficulties while using
the tuner, use this troubleshooting
guide to help you remedy the
problem. Should any problem
persist, consult your nearest Sony
dealer.
There’s no sound.
/ Connect the aerials.
/ Set the source setting on
the amplifier to TUNER.
You cannot tune in a frequency.
/ Adjust the position of the
aerial.
/ Connect an external aerial
for FM broadcasts.
/ Preset the stations again if
you've moved.
There is severe hum and/or
background noise.
/ Adjust the position or
direction of the aerial.
/ Tune to a correct
frequency.
/ Connect an external aerial
for FM broadcasts.
/ Move the tuner away from
the source of the noise.
RDS isn‘t working.
/ Make sure that you are
tuned to an FM station.
/ Select a stronger FM
station.
“No preset” appears in the display.
/ If the mains lead is
disconnected from the wall
outlet for more than one
month, the memory is
erased. Preset stations
again.
The station was interrupted by
another station / The tuner
automatically starts searching
stations.
/ The EON function is
working. Turn off EON
when you don't want the
current programme
interrupted.
The appropriate display or
information does not appear.
/ Turn the power off. Press
and hold AUTO-BETICAL
SELECT and the 5 button
and press POWER to turn
the power back on. This
empties any frequencies
stored in the preset
memory and returns the
display to the default
language (English).
/ Contact the radio station
and find out whether or
not they actually provide
the service in question. If
so, the service may be
temporarily out of order.
Additional Information
Frequency response
Separation
Selectivity
30 Hz - 15 kHz
(+0.5/–1.0 dB)
40 dB at 1 kHz
at 400 kHz
80 dB
at 300 kHz
60 dB
Output
Frequency range
Intermediate frequency
Usable Sensitivity
Signal-to-noise ratio
Harmonic distortion
Selectivity
Power requirements
Power consumption
Input impedance
Input connector
Dimensions
Weight
Supplied accessories
at 40 kHz deviation
600 mV
MW: 522 - 1,611 kHz
(9 kHz step)
LW: 144 - 288 kHz
(1 kHz step)
450 kHz
(with AM loop
aerial)
MW: 300 µV/m
LW: 1 mV/m
MW: 54 dB
(50 mV/m,
999 kHz)
LW: 50 dB
(50 mV/m,
216 kHz)
0.3% (50 mV/m,
400 Hz)
32 dB
220-230 V, AC
50/60 Hz
10 W
75 ohms
IEC-male
430 x 82 x 295 mm
(w/h/d)
2.7 kg
Audio cord (1)
AM loop aerial (1)
FM wire aerial (1)
EON control cord (1)
AM tuner section
General
Design and specifications are subject to
change without notice.
Specifications
FM tuner section
Frequency range
Aerial terminals
Intermediate frequency
65.0 - 74.0 MHz
87.5 - 108.0 MHz
75 ohms,
unbalanced
10.7 MHz
Sensitivity
Usable sensitivity (IHF)
S/N
Harmonic distortion
at 26 dB quieting
(mono) 10.3 dBf,
0.9 µV/75Ω
at 46 dB quieting
(stereo) 38.5 dBf,
23 µV/75Ω
10.3 dBf, 0.9 µV/
75Ω
at 40 kHz deviation
74 dB (mono),
69 dB (stereo)
0.1 % (mono),
0.2 % (stereo)
16
GB
Additional Information
Index
A, B
Aerial hookups
AM 4
FM 5
Amplifier hookups 5
Automatic tuning 9
Auto-betical select 6
C
Connecting. See Hookups
D
Display
language 6
mode 8
E
EON 13
F, G
FM mode 10
H, I, J, K, L
Hookups
AM aerial 4
amplifier 5
FM aerial 5
mains lead 5
M
Manual tuning 9
Memory 6, 10, 11
N
Naming stations 11
O
Organizing preset stations 12
P, Q
Presetting
AM stations 10
FM stations 6, 10
Preset tuning
AM stations 7
FM stations 7
PTY 14
R
RDS 13
Receiving preset stations 7
S
Signal meter 10
Storing radio stations. See
Presetting
T
Troubleshooting 15
Tuning. See Receiving
broadcasts
U, V, W, X, Y, Z
Unpacking 4
17
GB
2
PL
OSTRZEŻENIE
Aby nie zapobiec do pożarowi lub
porażeniu prądem elektrycznym, należy
chronić urządzenie przed deszczem lub
działaniem wilgoci.
Aby uniknąć porażenia prądem
elektrycznym, nie należy otwierać
obudowy. Naprawy urządzenia należy
powierzać specjalistom.
O ponownym pakowywaniu
• Nie wyrzucaj kartonu i innych
materiałów opakunkowych. Można je
będzie użyć jako idealnego
opakowania podczas przewozu
urządzenia. W przypadku wysyłki
urządzenia zapakuj je tak, jak było
zapakowane fabrycznie.
Jeżeli zaistnieją jakiekolwiek problemy
lub wątpliwości dotyczące niniejszego
urządzenia, o których nie ma mowy w
instrukcji obsługi, zwróć się po poradę
do najblizszego punktu sprzedaży
sprzętu Sony.
Ostrzeżenia
O bezpieczeństwie
• Jeżeli jakikolwiek płyn lub przedmiot
dostanie się do wnętrza urządzenia,
wyjmij wtyczkę z gniazdka i przed
ponownym użyciem zleć sprawdzenie
urządzenia kwalifikowanemu
personelowi.
O źródłach zasilania
• Przed rozpoczęciem użytkowania
upewnij się, że napięcie
eksploatacyjne twojego urządzenia
odpowiada napięciu w sieci lokalnej.
• Jeżeli urządzenie ma być nie
używane przez dłuższy okres czasu,
wyłącz wtyczkę z gniazdka
ściennego. Aby odłączyć przewód,
pociągnij ujmując za wtyczkę. Nigdy
nie ciagnij za sam przewód.
• Wymiana kabla zasilania może być
dokonana jedynie w kwalifikowanym
punkcie usługowym.
O lokalizacji
• Ustaw urządzenie w miejscu
zapewniającym wystarczającą
wentylację, aby uniknąć przegrzania
urządzenia i w ten sposób przedłużyć
możlliwy okres eksploatacji jego
elementów.
• Nie umieszczaj urządzenia w pobliżu
źródeł ciepła lub w miejscu
nasłonecznionym, szczególnie
zakurzonym lub narażonym na
wstrząsy mechaniczne.
• Nie umieszczaj na wierzchu
obudowy nic, co mogłoby blokować
wentylację i powodować wadliwe
funkcjonowanie.
• Nie instaluj urządzenia w przestrzeni
obudowanej, takiej jak półka na
książki, czy wbudowana szafka.
Czyszczenie
• Obudowę, płytę czołową i regulatory
czyść miękką ściereczką lekko
zwilżoną łagodnym detergentem. Nie
używaj szorstkiej tkaniny, proszku
czyszczącego oraz środków takich
jak alkohol czy benzyna.
3
PL
SPIS TREŚCI
Czynności wstępne
Rozpakowanie 4
Podłączanie zestawu 4
Wybór wyświetlenia w języku niemieckim 6
Wprowadzanie do pamięci stacji FM automatycznie (Wybór auto-
betyczny) 6
Działania podstawowe
Odbiór wprowadzonych do pamięci stacji 7
Zaawansowane działania tunera
O systemie korzystania z menu 8
Wybór rodzaju wyświetlenia 8
Odbiór programów 9
Wskazówki dla lepszego odbioru FM 10
Programowanie stacji radiowych 10
Nadawanie nazw zaprogramowanym stacjom 11
Porządkowanie zaprogramowanych stacji 11
Korzystanie z systemu danych radiowych (RDS) 13
Dodatkowe Informacje
W razie trudności 15
Dane techniczne 15
Indeks 16
Witaj !
Dziękujemy za zakup stereofonicznego
tunera FM/AM produkcji firmy Sony.
Przed rozpoczęciem użytkowania
niniejszego urządzenia prosimy
zapoznać się z instrukcją obsługi i
pozostawić ją w celu odwoływania się
do jej wyjaśnień w przyszłości.
Zasada
W niniejszej instrukcji użyty został
następujący znak:
Oznaczono nim porady i
wskazówki ułatwiające
postępowanie.
PL
4
PL
Czynności wstępne
Rozpakowanie
Sprawdź, czy wraz z tunerem otrzymałeś następujace
wyposażenie:
• Kabel audio (1)
• antenę ramową AM (1)
• antenę przewodową FM (1)
• kabel podłączeniowy EON (1)
Podłączanie zestawu
Przed rozpoczęciem
• Zanim rozpoczniesz podłączanie wyłącz zasilanie
wszystkich komponentów zestawu.
• Nie podłączaj zasilania z sieci dopóki nie wykonasz
wszystkich połączeń.
• Upewnij się, że połączenia są solidnie wykonane,
aby uniknąć przydźwięku i zakłóceń.
• Podczas podłączania kabla audio upewnij się, że
oznaczone kolorami wtyczki pasują do
odpowiadajacych im gniazdek: białe (lewe) do
białych, a czerwone (prawe) do czerwonych.
Podłączanie anteny AM
Ta część opisuje, jak podłączyć znajdującą się w
wyposażeniu antenę ramową AM. Lokalizację
specjalnych łączy AM ANTENNA sprawdź na poniższej
ilustracji.
AM ANTENNA
Co będzie mi potrzebne ?
• Antena ramowa AM (w wyposażeniu) (1)
1 Przed zamontowaniem anteny wyciągnij przewód
ze szczeliny w ramce anteny.
2 Odwiń trzy długości splecionego przewodu z
ramki anteny. Uważaj, aby odwinąć tylko
splecioną część przewodu. Nie odwijaj więcej niż
trzech długości przewodu. Uważaj także, aby go
nie rozpleść.
3 Zamontuj znajdującą się w wyposażeniu antenę
tak, jak to pokazano poniżej.
4 Podłącz antenę ramową AM do łączy na tyle
niniejszego urządzenia.
5 Wyreguluj kierunek anteny tak, aby osiągnąć
najlepszą jakość odbioru. Antena ramowa AM
posiada kierunkowość wykrywającą sygnał silniej
pod pewnym kątem, a słabiej pod innym. Ustaw
antenę tak, aby zapewnić najlepsze warunki
odbioru. W przypadku wystąpienia dudniena
podczas nagrywania audycji AM, wyreguluj
położenie anteny ramowej AM, aby zlikwidować
zakłócenia. Jeżeli mieszkasz w budynku z
żelbetonu lub o stalowej konstrukcji, uzyskanie
dobrej jakości odbioru może byc niemożliwe,
ponieważ fale radiowe we wnętrzu ulegną
osłabieniu. W takim przypadku polecamy
podłączenie dodatkowej anteny, takiej jak AN-1
produkcji firmy Sony.
Aby odbierać stacje trudne w odbiorze
Próbuj zmieniać ustawienie anteny podczas strojenia.
Ustawienie znajdujacej się w wyposażeniu anteny
ramowej AM w pobliżu okna pomoże uzyskać lepszą
jakość odbioru.
ANTENNA
FM
75 COAXIAL
AM
y
antena
ramowa AM
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
Страница загружается...
/