Yamaha v4 Инструкция по применению

Owner’s Manual

Keep This Manual For Future Reference.

Owner’s Manual

Contents

PRECAUTIONS................................... 5

Introduction .................................... 7

Welcome! ..........................................................7

Accessories.........................................................7

About utility software.........................................7

About firmware updates.....................................7

About the Owner’s Manual ................................7

Conventions in this manual................................7

An overview of the CL series ........... 8

Features .............................................................8

About the models ..............................................9

Controls and functions .................. 10

Top panel ........................................................10

Front Panel ......................................................16

Rear Panel........................................................16

Touch screen.................................. 18

Basic touch screen operations ..........................18

The on-screen user interface ............................18

Viewing the touch screen.................................20

Entering names................................................21

Using the tool buttons .....................................22

Using libraries ..................................................23

Initializing settings ...........................................26

Copying/pasting settings .................................26

Comparing two settings...................................27

Basic operation of the CL series .... 28

Controlling selected channels

(SELECTED CHANNEL section) ..................28

Controlling eight channels as a group

(Centralogic section).................................28

Using the top panel

(Channel Strip section)..............................29

Connections ................................... 31

About network connections .............................31

Connecting to I/O devices ...............................31

Audio input/output connections ......................33

Installing an option card ..................................34

Setup.............................................. 35

Specifying the brightness of the touch screen,

LEDs, channel name displays, and lamps...35

Setting the date and time of the internal

clock .........................................................35

Word clock connections and settings ...............36

Making HA (Head Amp) analog gain settings...37

Sending an input channel signal to the

STEREO bus...............................................38

Quick Guide ................................... 40

Connecting the devices....................................40

Setting the input channels ...............................41

Applying EQ/dynamics.....................................42

Setting the output channels .............................42

Using GEQ .......................................................42

Applying effects ...............................................43

Changing the patch settings ............................45

Grouping and linking.......................................46

Setting a custom fader bank ............................47

Using talkback..................................................47

Routing the oscillator to an output channel......48

Using scene memories .....................................48

Recording and playing audio using a USB

flash drive .................................................49

Saving and loading the unit settings ................50

Other functions ............................. 51

Initializing the unit to factory default settings...51

Restoring the current scene to the default

state..........................................................51

Adjusting the faders (Calibration function) .......52

Troubleshooting ............................ 53

Installing the MBCL meter bridge

(option) ......................................... 55

Specifications................................. 56

General specifications ......................................56

Input/output characteristics .............................57

Pin Assignment ................................................58

Dimensions .................................... 59

Index .............................................. 60

Block Diagram ............ End of Manual

Level Diagram............. End of Manual

Owner’s Manual

The above warning is located on the rear of the unit.

L’avertissement ci-dessus est situé sur l’arrière de l’unité.

Explanation of Graphical Symbols

Explication des symboles

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “danger-

ous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

L’éclair avec une flèche à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’une « tension

dangereuse » non isolée à l’intérieur de l’appareil, pouvant être suffisamment élevée pour constituer un risque d’électrocution.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (ser-

vicing) instructions in the literature accompanying the product.

Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’instructions

importantes sur l’emploi ou la maintenance (réparation) de l’appareil dans la documentation fournie.

IMPORTANT SAFETY

INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with the

manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat registers,

stoves, or other apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-type

plug. A polarized plug has two blades with one wider than the other. A

grounding type plug has two blades and a third grounding prong. The

wide blade or the third prong are provided for your safety. If the pro-

vided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched particularly

at plugs, convenience receptacles, and the point where they exit from

the apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to

avoid injury from tip-over.

13 Unplug this apparatus during lightning storms

or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such as

power-supply cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been

dropped.

(UL60065_03)

PRÉCAUTIONS CONCER-

NANT LA SÉCURITÉ

1 Lire ces instructions.

2 Conserver ces instructions.

3 Tenir compte de tous les avertissements.

4 Suivre toutes les instructions.

5 Ne pas utiliser ce produit à proximité d’eau.

6 Nettoyer uniquement avec un chiffon propre et sec.

7 Ne pas bloquer les orifices de ventilation. Installer l’appareil confor-

mément aux instructions du fabricant.

8 Ne pas installer l’appareil à proximité d’une source de chaleur comme

un radiateur, une bouche de chaleur, un poêle ou tout autre appareil

(y compris un amplificateur) produisant de la chaleur.

9 Ne pas modifier le système de sécurité de la fiche polarisée ou de la

fiche de terre. Une fiche polarisée dispose de deux broches dont une

est plus large que l’autre. Une fiche de terre dispose de deux broches

et d’une troisième pour le raccordement à la terre. Cette broche plus

large ou cette troisième broche est destinée à assurer la sécurité de

l’utilisateur. Si la fiche équipant l’appareil n’est pas compatible avec

les prises de courant disponibles, faire remplacer les prises par un

électricien.

10 Acheminer les cordons d’alimentation de sorte qu’ils ne soient pas

piétinés ni coincés, en faisant tout spécialement attention aux fiches,

prises de courant et au point de sortie de l’appareil.

11 Utiliser exclusivement les fixations et accessoires spécifiés par le

fabricant.

12 Utiliser exclusivement le chariot, le stand, le tré-

pied, le support ou la table recommandés par le

fabricant ou vendus avec cet appareil. Si l’appa-

reil est posé sur un chariot, déplacer le chariot

avec précaution pour éviter tout risque de chute

et de blessure.

13 Débrancher l’appareil en cas d’orage ou

lorsqu’il doit rester hors service pendant une période prolongée.

14 Confier toute réparation à un personnel qualifié. Faire réparer l’appa-

reil s’il a subi tout dommage, par exemple si la fiche ou le cordon

d’alimentation est endommagé, si du liquide a coulé ou des objets

sont tombés à l’intérieur de l’appareil, si l’appareil a été exposé à la

pluie ou à de l’humidité, si l’appareil ne fonctionne pas normalement

ou est tombé.

(UL60065_03)

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE DÉCHARGE

ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À

L’HUMIDITÉ.

Owner’s Manual

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions con-

tained in this manual, meets FCC requirements. Modifications not

expressly approved by Yamaha may void your authority, granted by

the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/

or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation

instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the

requirements listed in FCC Regulations, Part 15 for Class “B” digital

devices. Compliance with these requirements provides a reason-

able level of assurance that your use of this product in a residential

environment will not result in harmful interference with other elec-

tronic devices. This equipment generates/uses radio frequencies

and, if not installed and used according to the instructions found in

the users manual, may cause interference harmful to the operation

of other electronic devices. Compliance with FCC regulations does

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

not guarantee that interference will not occur in all installations. If

this product is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to elimi-

nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please con-

tact Yamaha Corporation of America, Electronic Service Division,

6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (U.S.A.)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in accordance

with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may not

correspond with the coloured markings identifying the terminals in

your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be connected

to the terminal in the plug which is marked by the letter E or by the

safety earth symbol or colored GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the terminal

which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the termi-

nal which is marked with the letter L or coloured RED.

(3 wires)

ADVARSEL!

Lithiumbatteri—Eksplosionsfare ved fejlagtig håndtering. Udskiftning

må kun ske med batteri af samme fabrikat og type. Levér det brugte

batteri tilbage til leverandoren.

VARNING

Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller

en ekvivalent typ som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantens instruktion.

VAROITUS

Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo

ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty

paristo valmistajan ohjeiden mukaisesti.

(lithium caution)

NEDERLAND / THE NETHERLANDS

• Dit apparaat bevat een lithium batterij voor geheugen back-up.

• This apparatus contains a lithium battery for memory back-up.

• Raadpleeg uw leverancier over de verwijdering van de batterij op het

moment dat u het apparaat ann het einde van de levensduur of

gelieve dan contact op te nemen met de vertegenwoordiging van

Yamaha in uw land.

• For the removal of the battery at the moment of the disposal at the

end of life please consult your retailer or Yamaha representative

office in your country.

• Gooi de batterij niet weg, maar lever hem in als KCA.

• Do not throw away the battery. Instead, hand it in as small chemical

waste.

(lithium disposal)

This product contains a battery that contains perchlorate material.

Perchlorate Material—special handling may apply,

See www.dtsc.ca.gov/hazardouswaste/perchlorate.

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

(Perchlorate)

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif.

90620

Telephone : 714-522-9011

Type of Equipment : Digital Mixing Console

Model Name : CL5/CL3/CL1

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interfer-

ence that may cause undesired operation.

See user manual instructions if interference to radio reception is sus-

pected.

(FCC DoC)

This product contains a high intensity lamp that contains

a small amount of mercury. Disposal of this material

may be regulated due to environmental considerations.

For disposal information in the United States, refer to

the Electronic Industries Alliance web site:

www.eiae.org

(mercury)* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

(class b korea)

Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid

the possibility of serious injury or even death from

electrical shock, short-circuiting, damages, fire or other

hazards. These precautions include, but are not limited

to, the following:

• Do not place the power cord near heat sources such as heaters or radiators, and

do not excessively bend or otherwise damage the cord, place heavy objects on

it, or place it in a position where anyone could walk on, trip over, or roll anything

over it.

• Only use the voltage specified as correct for the device. The required voltage is

printed on the name plate of the device.

• Use only the supplied power cord/plug.

If you intend to use the device in an area other than in the one you purchased,

the included power cord may not be compatible. Please check with your Yamaha

dealer.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it.

• Be sure to connect to an appropriate outlet with a protective grounding

connection. Improper grounding can result in electrical shock.

• This device contains no user-serviceable parts. Do not open the device or

attempt to disassemble the internal parts or modify them in any way. If it should

appear to be malfunctioning, discontinue use immediately and have it inspected

by qualified Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet conditions,

or place on it any containers (such as vases, bottles or glasses) containing

liquids which might spill into any openings. If any liquid such as water seeps

into the device, turn off the power immediately and unplug the power cord from

the AC outlet. Then have the device inspected by qualified Yamaha service

personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit. A burning item may fall

over and cause a fire.

• When one of the following problems occur, immediately turn off the power

switch and disconnect the electric plug from the outlet. Then have the device

inspected by Yamaha service personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the device.

CAUTION

Always follow the basic precautions listed below to avoid

the possibility of physical injury to you or others, or

damage to the device or other property. These

precautions include, but are not limited to, the following:

• When removing the electric plug from the device or an outlet, always hold the

plug itself and not the cord. Pulling by the cord can damage it.

• Remove the electric plug from the outlet when the device is not to be used for

extended periods of time, or during electrical storms.

• Do not place the device in an unstable position where it might accidentally fall

over.

• Do not block the vents. This device has ventilation holes at the rear to prevent

the internal temperature from becoming too high. In particular, do not place the

device on its side or upside down. Inadequate ventilation can result in

overheating, possibly causing damage to the device(s), or even fire.

• Do not place the device in a location where it may come into contact with

corrosive gases or salt air. Doing so may result in malfunction.

• Before moving the device, remove all connected cables.

• When setting up the device, make sure that the AC outlet you are using is easily

accessible. If some trouble or malfunction occurs, immediately turn off the

power switch and disconnect the plug from the outlet. Even when the power

switch is turned off, electricity is still flowing to the product at the minimum

level. When you are not using the product for a long time, make sure to unplug

the power cord from the wall AC outlet.

• When transporting or moving the device, always use two or more people.

Attempting to lift the device by yourself may damage your back, result in other

injury, or cause damage to the device itself.

• Before connecting the device to other devices, turn off the power for all devices.

Before turning the power on or off for all devices, set all volume levels to

minimum.

• Remove the power plug from the AC outlet when cleaning the device.

• Do not insert your fingers or hands in any gaps or openings on the device

(vents).

• Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.) into any

gaps or openings on the device (vents). If this happens, turn off the power

immediately and unplug the power cord from the AC outlet. Then have the

device inspected by qualified Yamaha service personnel.

• Do not rest your weight on the device or place heavy objects on it, and avoid use

excessive force on the buttons, switches or connectors.

• Do not use headphones for a long period of time at a high or uncomfortable

volume level, since this can cause permanent hearing loss. If you experience

any hearing loss or ringing in the ears, consult a physician.

Power supply/Power cord

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/Power cord

Location

Connections

Maintenance

Handling caution

PA_en_1 1/2

Owner’s Manual

• This device has a built-in backup battery that maintains internal clock data even

when the device’s power is switched off.

However, the backup battery will eventually become depleted, and when that

happens the internal clock data will be reset. Replace the backup battery before it

becomes fully depleted.

When the backup battery is running low, the LCD display indicates “Low

Battery” when you start up the system.

In this case, contact your Yamaha dealer and have qualified Yamaha service

personnel replace the backup battery.

The average life of the backup battery is approximately five years, depending on

operating conditions.

NOTICE

To avoid the possibility of malfunction/ damage to the

product, damage to data, or damage to other property,

follow the notices below.

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile

phone, or other electric devices. Otherwise, the instrument, TV, or radio may

generate noise.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or

heat (such as in direct sunlight, near a heater, or in a car during the day) to

prevent the possibility of panel disfiguration, damage to the internal

components or unstable operation.

(Verified operating temperature range: 5° – 40°C, or 41° – 104°F.)

• Do not place vinyl, plastic or rubber objects on the instrument, since this might

discolor the panel or keyboard.

• Condensation may occur if the ambient temperature around the device fluctuates

drastically (for example, if the device is relocated or placed under a fast-acting

air cooling or heating system, etc.).

Using the device while condensation is present may result in malfunction. Do

not turn on the power to the device for several hours until condensation

disappears. Only then is it safe to start the device.

• To protect against data loss through media damage, we recommend that you

save your important data onto two USB storage devices/external media.

Information

About copyrights

* Copying of the commercially available musical data including but not limited to

MIDI data and/or audio data is strictly prohibited except for your personal use.

About functions/data bundled with the instrument

* MPEG Layer-3 audio coding technology licensed from Fraunhofer

IIS and Thomson.

* Supply of this product does not convey a license nor imply any right

to distribute content created with this product in revenue-generating broadcast

systems (terrestrial, satellite, cable and/or other distribution channels),

streaming applications (via Internet, intranets, and/or other networks), other

content distribution systems(pay-audio or audio-on-demand applications and

the like) or on physical media (compact discs, digital versatile discs,

amiconductor chips, hard drives, memory cards and the like). An independent

license for such use is required.

For ditails, please visit http://mp3licensing.com/

About this manual

* The illustrations and LCD screens as shown in this manual are for instructional

purposes only, and may appear somewhat different from those on your

instrument.

* Windows is a registered trademark of Microsoft(R) Corporation in the United

States and other countries.

* Apple, Mac, Macintosh and iPad are trademarks of Apple Inc., registered in the

U.S. and other countries.

* The company names and product names in this manual are the trademarks or

registered trademarks of their respective companies.

Always turn the power off when the device is not in use.

(weee_eu)

Backup battery

Handling and Maintenance

Saving data

Yamaha cannot be held responsible for damage caused by improper use or

modifications to the device, or data that is lost or destroyed.

Information for Users on Collection and Disposal of Old

Equipment

This symbol on the products, packaging, and/or

accompanying documents means that used electrical

and electronic products should not be mixed with

general household waste.

For proper treatment, recovery and recycling of old

products, please take them to applicable collection

points, in accordance with your national legislation and

the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable

resources and prevent any potential negative effects on human health and the

environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please

contact your local municipality, your waste disposal service or the point of sale

where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your

dealer or supplier for further information.

[Information on Disposal in other Countries outside the European

Union]

This symbol is only valid in the European Union. If you wish to discard these

items, please contact your local authorities or dealer and ask for the correct

method of disposal.

PA_en_1 2/2

Introduction

Owner’s Manual

Introduction

Welcome!

Thank you for choosing a Yamaha CL series CL5/CL3/CL1

Digital Mixing Console. To take full advantage of the

superior features and performance offered by your

CL-series console, and to enjoy years of trouble-free use,

please read this owner’s manual carefully before operating

your console. After you have read the manual, keep it in a

safe place.

Accessories

• AC power cord

• Owner’s Manual (this book)

• Dante Virtual Soundcard Token leaflet

About utility software

CL-series products can be used with a variety of utility

software.

•CL Editor

This software application enables you to set up and operate

the unit from a connected computer. You can also use the

application to back up console settings or set console

parameters without connecting the unit.

• Console File Converter

This software application enables you to convert Yamaha

PM5D, M7CL, or LS9 settings files to or from CL-series

setting files.

• CL StageMix

This software application enables you to control the unit

remotely from an iPad on a WiFi network.

• MonitorMix

This app allows you to use your mobile device and a Wi-Fi

connection to adjust the CL-series console’s monitor mix

remotely.

Information about these software applications is available

on the Yamaha pro audio website:

http://www.yamahaproaudio.com/

Information about downloading, installing and setting up

the software applications is available on the website listed

above. In addition, refer to the installation guide that

comes with each downloaded application.

About firmware updates

This product enables you to update the unit firmware to

improve the operation, add functions, and correct possible

malfunctions. The following two types of firmware are

available for the unit.

• Console firmware

• Dante module firmware

You must update each type of firmware separately.

Details on updating the firmware are available on the

following website:

http://www.yamahaproaudio.com/

For information about updating and setting up the unit,

please refer to the firmware update guide available on the

website.

About the Owner’s Manual

Owner’s Manual (this book)

This book primarily explains panel controls and functions

and basic operation of the CL series.

Reference Manual (PDF format;

downloadable from the website)

This book primarily explains details about functions,

effects parameters, and MIDI.

Using the PDF manual

The Reference Manual is an electronic file in PDF format.

You can read this book on a computer. Use Adobe® Reader®

to read this book on screen, search for words very quickly,

print specific pages, or click links to display sections of

special interest. The ability to search for words, or to follow

links directly to relevant sections in the document, are

helpful attributes of this electronic file format. We

encourage you to take advantage of these benefits.

You can download the latest Adobe Reader application

from the website listed below.

http://www.adobe.com/

Help file (XML file; downloadable from

the website)

You can read this Help file on the unit’s screen. Install the

file on the unit, then press the Help button on the display to

view related sections.

You can download the Reference Manual and Help file

from the following website.

http://www.yamahaproaudio.com/

Conventions in this manual

In this manual, switch-type controls on the panel are called

“keys.” Control knobs on the panel are called “knobs.”

Some knobs rotate from a minimum value to a maximum

value, while others rotate endlessly.

Virtual buttons displayed on the screen are called “buttons,”

and virtual knobs are called “knobs.”

Controls located on the panel are enclosed in square

brackets [ ] (e.g., [CUE] key) to distinguish them from

virtual buttons and knobs displayed on screen. For certain

controls, the name of the section appears before the

brackets (e.g., SCENE MEMORY [STORE] key).

An overview of the CL series

Owner’s Manual

An overview of the

CL series

Features

CL series digital mixing consoles create high-quality,

refined, live-sound environments.

These consoles carry forward the digital evolution of a

broad array of advanced concepts, including Yamaha’s

exclusive “Centralogic

” control interface, which helps to

make the consoles easy and intuitive to use.

The built-in effect processor and an I/O device can

accommodate the most demanding situations at the

highest level of quality, while retaining the flexibility

necessary to configure a system that meets your needs.

User interface friendly to newcomers but

familiar to seasoned users

All channels routed to the top-panel faders are organized

into a “Fader Bank” that enables you to select and switch a

group of channels easily. The Fader Bank holds input and

output channel banks, as well as custom fader banks. The

custom fader banks enable you to select various

combinations of channels, regardless of channel types.

Each channel strip offers easy visual identification. The

channel name appears on a display, and an indicator shows

the channel color. You can adjust the brightness of each

indicator across a broad range to accommodate dimly-lit

environments.

The SELECTED CHANNEL section located to the left of

the display lets you use the knobs to control the main

parameters (gain, EQ, dynamics threshold, bus send levels,

etc.) for a particular channel. This section can be operated

much like a module in an analog mixer.

In the center of the top panel is the Centralogic section,

which enables you to control eight channels at once. You

can control fader, cue, on/off and other settings for the

eight channels or for DCA groups recalled to this section

by pressing a single key.

The display is a touch screen. You can turn functions on or

off or select items simply by touching buttons or knobs on

the screen.

Mix parameter settings, including gain and phantom

power for input channels, can be stored and recalled as

“scenes.” All faders on the panel are moving faders. When

you recall a scene, the recorded fader locations will be

reproduced immediately.

Flexible system configuration with Dante

The Ethernet-compatible Dante audio network protocol

facilitates connecting CL series consoles to external

devices, such as the Rio3224-D I/O device. A connected

I/O device that has been assigned a unique unit ID will

automatically be recognized and will facilitate patching

functions.

Using an I/O device, you can configure a redundant

network to defend against unforeseen difficulties that can

arise in large-scale Dante networks. If multiple CL units

share the same I/O device, the gain compensation function

will maintain network audio streams at a constant level to

help you enjoy the benefits of a large-scale sound system.

The Dante Virtual Soundcard software driver enables you

to carry out multi-channel recording to DAW software

installed on a computer. Consequently, no other audio

interface is needed.

Ultra-realistic digital reproduction of

analog sound by PREMIUM RACK

The CL series features PREMIUM RACK, which employs

VCM technology. This technology models analog circuitry

on a component level to faithfully reproduce amazing

analog sounds. PREMIUM RACK creates stunning sounds

by modeling and faithfully capturing the sonic

characteristics of analog circuitry fine-tuned to be faithful

to the original sound. The CL’s PREMIUM RACK includes

8 types, including a Portico 5033 EQ/Portico 5043

Compressor by Rupert Neve Designs, a U76 Compressor,

an Opt-2A Leveling Amplifier, etc.

Sonic flexibility from versatile effects and

GEQ rack

Independent of the PREMIUM RACK, high-quality

multi-effect processors are built into your CL series

console, with up to eight available simultaneously. Effects

such as reverb, delay, multiband compression, and various

modulation effects can be routed via internal buses or

inserted into the desired channel.

In addition to the effects, the CL series features a GEQ rack.

A 31BandGEQ, a Flex15GEQ, an 8BandPEQ, an 8ch

Automixer and a 16ch Automixer are included and can be

inserted into any output bus. The Flex15GEQ allows you to

adjust the gain for any 15 of the 31 bands. Since two GEQ

units can be mounted in one virtual rack, a total of up to 32

GEQ units can be used simultaneously. To use effects or the

graphic EQ, you mount them in virtual racks displayed on

the touch screen. The currently-mounted modules can be

seen at a glance, and you can switch modules and change

input/output patching in an intuitive manner.

Complete support tools

The CL-series can be used with a variety of utility software.

CL Editor, which can be installed on Windows or Mac

computers, enables you to edit the unit’s parameter settings.

It can also operate as a stand-alone and lets you set

parameters off-line without connecting to the console.

CL StageMix, an application for iPads, offers remote

control of a networked CL series console from anywhere

within wireless range via an intuitive graphical interface.

The software has been specifically designed to allow

engineers to adjust EQ while monitoring mixes from the

performers’ positions on stage, or to control mix

parameters from various spots in the venue while listening

to the sound.

MonitorMix is an iOS-compatible app that allows

performers to adjust the levels of the monitor mix directly

from the stage.

Console File Converter is an application that converts

PM5D/M7CL/LS9 settings files to or from the CL series

settings file format. You can use data from other models on

the CL series.

About the models

Owner’s Manual

I/O card and processing card expansion

The rear panel provides three slots in which separately sold

mini-YGDAI cards can be installed. You can add inputs

and outputs by installing AD cards, DA cards, or digital I/O

cards in these slots. You can also expand processing or

effects by installing a DSP card.

Cascade connections in the digital

domain

You can cascade a second CL series unit or a digital mixer,

such as the Yamaha M7CL, PM5D or LS9, connected via a

digital I/O card installed in a slot.

You can cascade any of the MIX, MATRIX, STEREO (L/R),

MONO, and CUE (L/R) buses.

Recorder function useful for sound checks

and mix recording

The CL series features a USB memory recorder function

that enables you to record output from STEREO or MIX

buses onto a USB flash drive.

It also enables you to play audio files that reside on a USB

flash drive by assigning the files to input channels or

monitor outputs. The MP3 format (MPEG-1 Audio

Layer-3) is supported for recording. For playback, MP3,

WMA (Windows Media Audio), and MPEG-4 AAC

(Advanced Audio Coding) formats are supported. This

function can be useful if you want to record certain bus mix

outputs or play music for a sound check through speakers.

Security functions at user or system level

Functionality can be restricted for users other than the

administrator at three levels of security: administrator,

guest, and user. Passwords can be specified for the

administrator and for users to help prevent important

settings from being changed accidentally

Information specific to each user (user level, system

settings, and user-defined key/knob settings) can be stored

in the console or on a USB flash drive as a “user

authentication key.” By loading your own user

authentication key, you can instantly set up the ideal

operating environment for yourself.

Help file downloadable to the unit

You can download from the website a Help file that explains

the parameters and messages displayed on the screen. Once

you download the Help file, it will be stored inside the unit

so that you can use the Help function at any time.

About the models

The CL series is available in three models: CL5, CL3, and

CL1. Each model features a different number of monaural

input channels and top-panel channel strips. In addition,

the CL5 features an Output Meter section. The CL3 and

CL1 allow you to install an optional MBCL meter bridge.

Other functions are common to all three models. Model

differences are shown in the table below.

NOTE

In this manual, most explanations refer to the CL5.

Monaural

input channels

Channel strips

Output

meters

CL5 72

Block A: 16

Block B (Centralogic section): 8

Block C: 8

MASTER section: 2

Ye s

CL3 64

Block A: 16

Block B (Centralogic section): 8

MASTER section: 2

Optional

MBCL

CL1 48

Block A: 8

Block B (Centralogic section): 8

MASTER section: 2

Optional

MBCL

Block A Centralogic section

(Block B)

Output meter

MASTER section

Block C

•CL5

Block A Centralogic section

(Block B)

MASTER section

Meter bridge

MBCL (optional)

•CL3

Block A Centralogic section

(Block B)

MASTER section

Meter bridge

MBCL (optional)

•CL1

Controls and functions

Owner’s Manual

Controls and functions

Top panel

The top panel of the CL series is divided into the following sections.

1 Channel Strip section ➔ page 11

2 SELECTED CHANNEL section ➔ page 12

3 Display section ➔ page 13

4 Centralogic section ➔ page 13

5 SCENE MEMORY/MONITOR section ➔ page 14

6 USER DEFINED KNOBS section ➔ page 14

7 USER DEFINED KEYS section ➔ page 14

8 Master section ➔ page 15

9 USB connector ➔ page 15

0 Meter section (for CL5 only) ➔ page 15

NOTE

This illustration shows the top panel of the CL5.

The CL3 and CL1 do not feature a Meter section, but enable you to install an optional MBCL meter bridge.

236j

118

Top panel

Owner’s Manual

Channel Strip section

1 GAIN/PAN/ASSIGN knob

Adjusts the gain or pan of the channel. You can also

assign a parameter to this knob.

You can switch the function of the knob by using the

9 [GAIN/PAN/ASSIGN] key.

A gain parameter value indicated on the display or

channel name display indicates the amount of

amplification of a currently-input signal. Refer to the

Conversion Table for information on the relationship

to input sensitivity.

Conversion Table for Input Sensitivity

2 [SEL] key

Selects a channel that will be controlled in the

Channel Strip section and on the touch screen. When

a channel is selected, the key LED will light.

If you control an ST IN channel in Block A of the

Channel Strip section, the L channel will be routed to

an odd-numbered channel, and the R channel will be

routed to the adjacent even-numbered channel.

If you control a channel in the CUSTOM bank or in

Block C of the Channel Strip section, and if you assign

L/R channels, the selected object of control will

alternate between the L and R channels each time you

press the [SEL] key.

NOTE

If you assign either the L or R channel, this key will simply

select the channel.

3 [CUE] key

Selects the channel to be cue-monitored. If the cue is

on, the key LED will light.

4 Meter LEDs

Indicate the channel level.

5 [ON] key

Switches the channel on or off. If a channel is on, the

key LED will light. In SENDS ON FADER mode, this

is an on/off switch for signals sent from each channel

to the currently-selected MIX/MATRIX bus.

6 Channel name display

Indicates the channel name, knob value, fader value,

etc. You can set the display so that it will indicate only

the channel name. Use the PREFERENCE tab in the

USER SETUP screen to select information to be

displayed.

7 Channel color indicator

Lights in a color specified on the PATCH/NAME

screen. You can select the channel color from eight

options.

8 Fader

Adjusts the input/output level of the channel. In

SENDS ON FADER mode, this fader adjusts the send

level of the signal from each channel to the

currently-selected MIX/MATRIX bus.

9 [GAIN/PAN/ASSIGN] key

Switches the knob function for each block on the

channel strip. The LED for the selected function will

light. Use the USER DEFINED KNOBS tab in the

USER SETUP screen to select a parameter to control

when the ASSIGN function is selected.

0 Bank Select keys

These keys switch the channel faders controlled in the

Channel Strip section. The [CUSTOM] keys enable

you to select your own custom fader bank. For details

on the custom fader banks, refer to page 47.

Gain Input Sensitivity

–6dB +10dBu

0 +4dBu

+66dB –62dBu

Controls and functions

Owner’s Manual

SELECTED CHANNEL section

This section enables you to set the mix parameters for the

currently-selected channel.

1 [MIX1–16] key/[MIX17–24/MATRIX] key

Select a MIX or MATRIX bus that is controlled by the

knobs located below the keys.

2 [1]–[16] knobs

Adjust the send level from currently-selected channels

to the MIX or MATRIX bus.

In SENDS ON FADER mode, push in a knob to select

the corresponding destination bus. Push the knob

again to turn the cue monitor on for the

corresponding MIX/MATRIX channel.

NOTE

If the SIGNAL TYPE of the destination bus is set to

STEREO, use the left knobs (odd-numbered channels) to

adjust PAN and the right knobs (even-numbered channels)

to adjust the send level.

3 [GAIN] knob

Adjusts the head amp’s analog gain for an input

channel.

On the other hand, it adjusts the digital gain if GAIN

KNOB FUNCTION is set to DIGITAL GAIN in the

PREFERENCE tab of the USER SETUP screen.

This knob has no effect for other types of channels.

NOTE

• The PAD will be switched on or off internally when the HA

analog gain is adjusted between +17 dB and +18 dB.

Keep in mind that noise may be generated when using

phantom power if there is a difference between the Hot and

Cold output impedance of an external device connected to

the INPUT connector.

• The gain parameter value indicates the amount of

amplification of the currently-input signal. Refer to the

Conversion Table (page 11) for information on the

relationship to conventional input sensitivity values.

4 [PAN] knob

When a monaural channel is selected, this knob

adjusts the panning of the signal sent to the STEREO

bus.

When a stereo channel is selected, this knob adjusts

the PAN or left/right balance, whichever is selected.

5 [DYNAMICS 1] knob

6 [DYNAMICS 2] knob

Adjust the THRESHOLD parameter of the gate,

compressor, etc.

The [DYNAMICS 2] knob has no effect if the MIX,

MATRIX, STEREO, or MONO channel is selected.

7 [HPF] knob

Adjusts the HPF cutoff frequency for an input

channel. It has no effect on other types of channels.

8 EQ [Q], EQ [FREQUENCY], EQ [GAIN] knobs

For each band of the four-band EQ, these knobs adjust

the Q, center frequency (cutoff frequency), and gain.

Press the EQ [Q] and EQ [GAIN] knobs

simultaneously to reset the GAIN setting for each

band to the default value (0.0 dB).

Top panel

Owner’s Manual

Display section

This is a touch screen that you can operate by touching the

surface of the screen. You can touch your finger to the

screen to select menus or set parameters. Please note that

you cannot operate the unit by touching multiple points

simultaneously.

NOTE

If the touch screen becomes dirty, wipe it with a soft dry

cloth.

NOTICE

Never use a sharp or pointed object such as your fingernail

to operate the touch panel. Doing so may scratch the

screen and render the touch screen inoperable.

Centralogic section

This section enables you to control up to eight channel

modules that are selected from channel groups, DCA

groups, or custom groups selected by the Bank Select keys.

1 Bank Select keys

Select a bank to be controlled in the Centralogic

section. Press the [INPUT] key, then press one of the

Bank Select keys below to route the channel bank

(labeled to the left of the key) to the Centralogic

section. Press the [OUTPUT] key, then press one of

the Bank Select keys below to route the channel

(labeled to the right of the key) to the Centralogic

section.

2 Multifunction knob

Controls the knob currently selected on the touch

screen. The knob function can vary depending on the

screen currently displayed.

3 [SEL] key

4 [CUE] key

5 Meter LEDs

Same as those in the Channel Strip section.

6 [ON] key

Switches the channel on or off. If a channel is on, the

key LED will light. In SENDS ON FADER mode, this

is an on/off switch for signals sent from each channel

Controls and functions

Owner’s Manual

to the currently-selected MIX/MATRIX bus. If the

graphic EQ is used, this key resets the gain to 0 dB.

7 Channel name display

8 Channel color indicator

Same as that in the Channel Strip section. If the

graphic EQ is used, this indicator displays the

frequency and gain parameter value.

9 Fader

Adjusts the input/output level of the channel. You can

also make internal settings so that the fader will be

used as a controller to adjust the gain of each GEQ

band.

SCENE MEMORY/MONITOR section

In this section you can perform operations for scene

memory and monitoring.

1 SCENE MEMORY [STORE] key

Stores the current mix parameter settings in a

dedicated scene memory.

2 SCENE MEMORY [RECALL] key

Recalls a scene (previously-saved settings) from scene

memory.

3 SCENE MEMORY [INC]/[DEC] keys

Select the scene number of a scene that you want to

store or recall. The number of the currently-selected

scene appears in the function access area on the right

of the touch screen.

Press the [INC]/[DEC] keys simultaneously to return

to the current scene number.

4 [UNDO] key

Cancels the scene recall and recovers the status

obtained prior to recall. The key LED lights if you can

still cancel the scene recall.

5 [PREVIEW] key

This key selects PREVIEW mode, which lets you view

the scene settings in the display and the panel without

affecting the signal processing of the current scene.

6 [MONITOR LEVEL] knob

Adjusts the signal level of the monitor output. If the

PHONES LEVEL LINK function is turned on in the

MONITOR screen, this knob will also adjust the

signal level at the PHONES Out jack located on the

front panel.

USER DEFINED KNOBS

section

USER DEFINED knobs [A]–[D]

Control the parameters that have been

assigned by the user (input channel

digital gain, high-pass filter frequency,

etc.).

You can assign various parameters at will.

Use the USER SETUP popup window in

the SETUP screen to assign the

parameters.

USER DEFINED KEYS

section

USER DEFINED keys [1]–[16]

Execute functions as assigned by the user

(scene changes, switching the talkback or

internal oscillator on/off, etc.). Use the

USER SETUP popup window to assign

functions.

126

Top panel

Owner’s Manual

Master section

This section is similar to the Channel Strip section, and

enables you to control the principal parameters of the

assigned channels. When the unit is in the default state,

STEREO/MONO channels are assigned.

1 GAIN/PAN/ASSIGN knob

Adjusts the gain or pan of the

channel. You can also assign

parameters to the knob.

On the CL5, switch the

function of the knob using the

[GAIN/PAN/ASSIGN] key

located to the left of the Master

section. On the CL3 and CL1,

switch the function of the knob

using the

[GAIN/PAN/ASSIGN] key

located in the upper right

corner of the Block A in the

Channel Strip section.

2 [SEL] key

Selects the channel you wish to

control. Pressing this key will

cause the channel LED to light

up, and you will be able to

control the channel in both the

SELECTED CHANNEL

section and on the touch

screen.

If the STEREO bus has been

assigned, the selected object of

control will alternate between

the L and R channels each time

you press the [SEL] key.

3 [CUE] key

Selects the channel to be

cue-monitored. If cue is on, the

LED will light.

4 [ON] key

Switches the channel on or off. If a channel is on, the

key LED will light.

If MONITOR has been assigned, this key switches the

monitor output on or off.

5 Channel name display

6 Channel color indicator

Same as that in the Channel Strip section.

7 Fader

Adjusts the output level of the channel.

If MONITOR has been assigned, this fader adjusts the

monitor output level.

USB connector

You can connect a USB flash drive to

the USB connector to record or play

audio files, and to save or load

internal data. The Help file displayed

on the unit screen is loaded from a

connected USB flash drive.

You can also save on a USB flash drive “User authentication

key” data that determines the user level and limit the

functionality to which the user has access.

NOTE

Operation is guaranteed only for a connection with a USB

flash drive.

■ USB flash drive capacities and formats

The operation of USB flash drives with capacities of up to

32 GB has been verified. (However, this does not guarantee

operation of all USB flash drives.)

The FAT16 and FAT32 formats are supported.

■ Prevention of accidental erasure

Some USB flash drives have a write-protect setting that lets

you prevent data from being erased accidentally. If your

flash drive contains important data, it is a good idea to use

the write-protect setting to prevent accidental erasure.

On the other hand, you will need to make sure that your

USB flash drive’s write-protect setting is turned off before

you save data onto it.

NOTICE

An ACCESS indicator appears in the Function Access

Area while data is being accessed (saved, loaded, or

deleted). During this time, do not disconnect the USB flash

drive or power-off the CL unit. Doing so may damage your

flash drive, or may damage the data in the CL unit or on

your media device.

Meter section (for CL5 only)

Indicates the level of MIX/MATRIX, STEREO/MONO and

CUE channels. You can select the monitoring position from

PRE EQ (immediately before EQ), PRE FADER

(immediately before the fader), or POST ON (immediately

after the [ON] key).

You can use this function on the CL3 or CL1 if you install

an optional MBCL meter bridge.

Controls and functions

Owner’s Manual

Front Panel

1 PHONES LEVEL knob

Adjusts the level of the signal output from the

PHONES Out jack.

2 PHONES Out (headphone output) jack

Lets you monitor the MONITOR OUT or CUE signal.

3 TALKBACK jack

A balanced XLR-3-31 jack to which a talkback mic

can be connected. You can make settings in the screen

to supply +48V phantom power to this jack. This jack

sends instructions from the mixer operator to the

desired output channel.

4 TALKBACK LEVEL knob

Adjusts the input level of the mic connected to the

TALKBACK jack.

Rear Panel

1 LAMP connectors

Four-pin female XLR output jacks that supply power

to separately-sold gooseneck lamps (such as the

Yamaha LA1L). (The CL3 includes these connectors at

two locations. The CL1 includes one.)

2 MIDI IN/OUT connectors

Used to transmit and receive MIDI messages to and

from external MIDI devices. The MIDI IN connector

receives messages from an external device, and the

MIDI OUT connector transmits messages from the

CL unit.

These are used mainly to record CL parameter

operations or scene/library selections on an external

device, or to control CL parameters from an external

device.

3 WORD CLOCK IN/OUT connectors

BNC connectors used to transmit and receive word

clock signals to and from an external device. The

WORD CLOCK IN connector features internal

75-ohm termination.

4 GPI connector

D-sub 15-pin female connector that allows

communication (5-in/5-out) with a GPI-equipped

external device.

5 DIGITAL OUT connector

An AES/EBU (XLR-3-32 male) jack that outputs the

digital audio signal of a desired channel in AES/EBU

format.

6 OMNI IN jacks

Balanced XLR-3-31 female input jacks that input

analog audio signals from line level devices or

microphones. Nominal input level is −62 dBu to

+10 dBu.

7 OMNI OUT jacks

XLR-3-32 male output jacks that output analog audio

signals. These jacks are used mainly to output the

signals of MIX channels or MATRIX channels.

Nominal output level is +4 dBu.

12 34

21 3 4 5

876 A90 C D FEB

Male XLR plug

1 (Ground)

3 (Cold)

2 (Hot)

Female XLR plug

1 (Ground)

3 (Cold)

2 (Hot)

Rear Panel

Owner’s Manual

NOTE

Although OMNI OUT jacks feature a nominal input/output

level of +4 dBu (maximum level +24 dBu), an internal

switch allows this to be changed to –2 dBu (maximum level

+18 dBu) if necessary. (A fee will be charged for this

procedure.) For details, contact your Yamaha dealer.

8 Dante PRIMARY/SECONDARY connectors

Used to connect to other Dante-compatible network

devices, such as an Rio3224-D I/O device.

Use standard Ethernet cables with Neutrik etherCON

CAT5 compatible RJ-45 plugs.

NOTE

Use STP (shielded twisted pair) cable to prevent

electromagnetic interference. Make sure that the metal

parts of the plugs are electrically connected to the STP

cable shield by conductive tape or comparable means.

9 LINK/ACT Indicators

These indicators show the communication status of

the PRIMARY and SECONDARY connectors.

They flash fast if the Ethernet cables are connected

properly.

0 1G Indicators

These indicators light when the Dante network is

functioning as Giga-bit Ethernet.

A NETWORK connector

Allows the CL unit to be connected to a computer via

an Ethernet cable (CAT5e or higher recommended).

This connector is used mainly to control mix

parameters or to edit scene memories and libraries

from the dedicated “CL Editor” application program

or “StageMix” iPad application.

NOTE

Use STP (shielded twisted pair) cable to prevent

electromagnetic interference. Make sure that the metal

parts of the plugs are electrically connected to the STP

cable shield by conductive tape or comparable means.

B SLOT 1–3

Allow for the installation of separately-sold DSP

cards, or mini-YGDAI I/O cards to expand the

number of input/output ports.

C DC POWER INPUT connector

You can connect the separately-sold PW800W power

supply here as a backup external power supply. If the

PW800W is connected, the CL unit will continue

receiving power from the PW800W, even if its own

internal power supply shuts down due to a problem.

Caution

If you plan to connect the PW800W, be sure to first

power-off both the CL unit and the PW800W. Then, use the

power supply cable (PSL360) to make the connection.

Failure to observe this caution may cause malfunction or

electric shock.

NOTE

• If a PW800W is connected, the CL series will operate

correctly whether its own internal power supply and the

PW800W are both turned on, or just one of them is turned

on.

• If both power supplies are turned on, and an abnormality

is detected in one of the power supplies, the CL series will

automatically switch to the other power supply. If this

occurs, the touch screen will display a message to inform

you.

D AC IN connector

Connect the supplied AC power cable here. First

connect the AC power cable to the CL unit, then insert

the power cable plug into an AC power outlet.

The supplied AC power cable features a special

latching mechanism (V-LOCK) to prevent the power

cable from being disconnected accidentally.

Connect the power cable by inserting the cable plug

fully until it is locked.

Caution

Be sure to turn the power off before connecting or

disconnecting the power cable.

To disconnect the power

cable, press the latch button

on the plug.

E (Power Switch)

This switch turns power on or off. When the power

switch is set to , the power to the unit is on. When

the power switch is set to , the power to the unit is

off.

Caution

• Rapidly turning the unit on and off in succession can cause

it to malfunction. After turning the unit off, wait for at least 6

seconds before turning it on again.

• Even when the power switch is turned off, a small amount

of current is flowing through the unit. If you plan not to use

the unit for a long period of time, remove the power cable

from the AC outlet.

F Grounding screw

The supplied AC power cable is a 3-wire type.

Therefore, if the AC outlet used is properly grounded,

the CL will be grounded as well. Also, grounding this

screw may effectively eliminate noise such as hum and

interference.

Touch screen

Owner’s Manual

Touch screen

Basic touch screen

operations

This section explains the basic procedures you can perform

on the CL’s touch screen. In general, you will operate the CL

using an appropriate combination of the operations

explained here.

Pressing the touch screen

You will mainly use this operation to switch screens and

pages, to select a parameter to operate, and to turn a button

on or off. Certain buttons let you specify a number based

on the area of the button itself that you touch.

Multiple selection (specifying a range)

While pressing your finger on the touch panel, move it in

the left or right direction to specify a range within a

character string. You will use this technique primarily

when assigning a name to a scene or library.

For the channel select buttons, you can select multiple

buttons by moving your finger across the touch screen

while continuing to press down.

NOTE

This makes it easy to select a range of buttons to be turned

on or off together.

Special key operations

Typically, you will press a top panel key once, but in certain

cases you can access special functions by rapidly pressing a

key twice in succession.

Knob operations

Typically, knobs are rotated left or right to change the value

of the corresponding parameter. By pressing a knob, you

can recall a specific screen.

For certain parameters, you can adjust the value in finer

steps (greater detail) by rotating the knob while pressing it.

Multifunction knob operations

Multifunction knobs 1–8 are used to operate knobs

selected in the touch screen.

A thick line will be displayed around a selected knob if it

can be controlled by a multifunction knob. (Typically, a

knob of this type corresponds to the multifunction knob

located immediately below it and allows you to control up

to eight parameters simultaneously.)

While a knob is selected, turning the multifunction knob

located immediately below it will change the value of the

corresponding parameter.

In the SCENE LIST screen, you can select multiple items by

rotating a multifunction knob while pressing it.

The on-screen user interface

The section below explains various user interface

components that appear in the touch screen, and how to

use them.

Tabs

Tabs enable you to switch between multiple pages. Each tab

indicates its page name.

Buttons

Buttons are used to execute specific functions, to switch

parameters on or off, or to select one of the multiple

choices. Buttons that perform on/off operations appear in

solid colors while they are turned on, and dark while when

turned off.

When you press a button labeled with two overlaid “■”

symbols or a “▼” mark, a separate window will open,

allowing you to make detailed settings.

Faders / Knobs

Faders and knobs on screen move in tandem when you

operate the top panel faders and knobs. The current value

appears immediately below the fader or knob.

If you press once a knob that can be operated by a

multifunction knob, a thick frame appears around the

knob. This frame indicates that the knob has been selected

for operation.

NOTE

Pressing certain knobs a second time while a thick frame

is displayed around them will open a window in which you

can make additional detailed settings.

Buttons

Ta bs

The on-screen user interface

Owner’s Manual

List windows

Windows similar to the following enable you to select items

from a list, such as a list of USER DEFINED keys.

The highlighted item in the middle indicates it has been

selected for operation. Press the arrow / below the list

to scroll the list up or down.

NOTE

• You can also scroll the list up or down by using the

multifunction knob.

• If there is more than one list on the screen, your operations

will apply to the list surrounded by a pink frame. You can

press the multifunction knob to move the focus of your

operations to the next column.

Keyboard window

The keyboard window enables you to assign a name or

comment to a scene or library, or to assign a name to a

channel. Press the keys in the window to enter the

corresponding character.

Popup windows

When you press a button or field for a specific parameter in

a screen, a window showing detailed parameters or lists

will appear. This type of window is called a “popup

window.”

You can switch between popup windows using tabs as

needed.

Some popup windows show several buttons called “tool

buttons” at the top of the window. You can use these tool

buttons to recall libraries or to perform copy and paste

operations.

Press the “X” symbol to close the popup window and

return to the previous screen.

Dialog boxes

Dialog boxes similar to the following enable you to confirm

operations you just performed.

Press the OK button to execute the operation. The

operation will be canceled if you press the CANCEL

button.

Touch screen

Owner’s Manual

Viewing the touch screen

The touch screen of the CL series is broadly divided into

two areas.

Function access area

1 Selected channel

This field indicates the number,

name, icon and channel color

of the channel that is currently

selected for operation. Press the

left half of the selected channel

to switch to the preceding

channel; press the right half to

switch to the next channel.

2 Time

This area indicates the

current time.

3 Status Indicator

This area indicates the

current unit status. Normally

it indicates the name of the

user who is currently logged

in (i.e., is authenticated and

able to operate the system).

The following table shows the

indications and their

corresponding status.

*1 The signal type (IN/OUT/DCA/KEYIN/EFFECT) is shown in the

upper part of the CUE meter.

This indicator appears when the operation switches from the primary

to the secondary Dante audio network in a redundant connection

NOTICE

An ACCESS indicator appears in the Function Access

Area while data is being accessed (saved, loaded, or

deleted). During this time, do not disconnect the USB flash

drive or power-off the CL unit. Doing so may damage your

flash drive, or may damage the data in the CL unit or on

your media device.

4 HELP

Pressing this button will show on-line help in the

main area. To view the on-line Help, first you must

load the Help file from a USB flash drive. Once the

Help file has been loaded, it will be kept in internal

memory.

5 SENDS ON FADER

Press this button to switch to SENDS ON FADER mode,

where you can use the faders of the top panel to adjust

the MIX/MATRIX send level. During this time, the

function access area will switch to a screen that enables

you to select the send-destination MIX/MATRIX bus.

6 I/O DEVICE

When you press this button, the I/O DEVICE screen

will appear in the main area, allowing you to make

settings for I/O devices and external head amps.

7 CH JOB (Channel Job)

When you press this button, the CH JOB menu which

allows you to group and link channels will appear,

allowing you to select the function you want to operate.

8 RACK

When you press this button, the VIRTUAL RACK

screen will appear in the main area, allowing you to

edit the GEQ and effect settings.

9 MONITOR

When you press this button, the MONITOR screen

will appear in the main area, allowing you to edit the

monitor or oscillator settings.

0 METER

These are level meters that show the level of the

STEREO bus (L/R), MONO bus (M), and cue signal

(CUE). When you press this field, the METER screen

will appear in the main area. If you press part of the

CUE meters when the cue monitor is on, the cue

monitor will be canceled.

A SETUP

When you press this button, the SETUP screen will

appear in the main area, allowing you to make basic

system settings and user-specific settings.

B RECORDER

When you press this button, the recorder screen will

appear in the main area, allowing you to operate and

set up the recorder function (USB/Nuendo Live) for

audio recording and playback.

C SCENE

This area indicates the number and title of the scene

that was last stored or recalled. An “R” symbol is

displayed for read-only scenes, and a lock icon is

displayed for write-protected scenes. If you edit the

parameters from their last stored or recalled state, an

“E” symbol will appear in the lower right. When you

press this field, the SCENE LIST screen will appear in

the main area, allowing you to store or recall scenes.

In PREVIEW mode, this field is shown in red.

D USER DEFINED KEY

This area indicates the bank for the USER DEFINED

key that is currently selected.

Indication Status

OSC Oscillator enabled

TALKBACK Talkback enabled

CUE Cue monitor on*

ACCESS Accessing internal memory or USB memory

PATCHING Now performing Dante patching

ALT ALTERNATE mode enabled

PLAY Playing an audio file

REC Recording an audio file

SECONDARY

Switching to the secondary network

Function access areaMain area

Страница загружается...

Yamaha v4, CL1, CL3, CL5 Инструкция по применению

Похожие модели бренда

Модели других брендов