Yamaha TIO1608-D Инструкция по применению

Owner’s Manual

Bedienungsanleitung

Mode d’emploi

Manual de instrucciones

Manual do Proprietário

Manuale di istruzioni

Руководство пользователя

AUDIO INTERFACE

EnglishDeutschFrançaisEspañolPortuguêsItalianoРусский

Tio1608-D

I/O RACK

Owner’s Manual

Tio1608-D

The above warning is located on the rear of the unit.

L’avertissement ci-dessus est situé sur l’arrière de l’unité.

Explanation of Graphical Symbols

Explication des symboles

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

L’éclair avec une flèche à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’une «

tension dangereuse » non isolée à l’intérieur de l’appareil, pouvant être suffisamment élevée pour constituer un risque d’électrocution.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the product.

Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’instructions

importantes sur l’emploi ou la maintenance (réparation) de l’appareil dans la documentation fournie.

IMPORTANT SAFETY

INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than the

other. A grounding type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided for your

safety. If the provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms

or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has

been dropped.

PRÉCAUTIONS CONCER-

NANT LA SÉCURITÉ

1 Lire ces instructions.

2 Conserver ces instructions.

3 Tenir compte de tous les avertissements.

4 Suivre toutes les instructions.

5 Ne pas utiliser ce produit à proximité d’eau.

6 Nettoyer uniquement avec un chiffon propre et sec.

7 Ne pas bloquer les orifices de ventilation. Installer l’appareil

conformément aux instructions du fabricant.

Ne pas installer l’appareil à proximité d’une source de chaleur

comme un radiateur, une bouche de chaleur, un poêle ou tout autre

appareil (y compris un amplificateur) produisant de la chaleur.

9 Ne pas modifier le système de sécurité de la fiche polarisée ou de

la fiche de terre. Une fiche polarisée dispose de deux broches dont

une est plus large que l’autre. Une fiche de terre dispose de deux

broches et d’une troisième pour le raccordement à la terre. Cette

broche plus large ou cette troisième broche est destinée à assurer

la sécurité de l’utilisateur. Si la fiche équipant l’appareil n’est pas

compatible avec les prises de courant disponibles, faire remplacer

les prises par un électricien.

10 Acheminer les cordons d’alimentation de sorte qu’ils ne soient pas

piétinés ni coincés, en faisant tout spécialement attention aux

fiches, prises de courant et au point de sortie de l’appareil.

11 Utiliser exclusivement les fixations et accessoires spécifiés par le

fabricant.

12 Utiliser exclusivement le chariot, le stand, le

trépied, le support ou la table recommandés par

le fabricant ou vendus avec cet appareil. Si

l’appareil est posé sur un chariot, déplacer le

chariot avec précaution pour éviter tout risque

de chute et de blessure.

13 Débrancher l’appareil en cas d’orage ou

lorsqu’il doit rester hors service pendant une période prolongée.

14 Confier toute réparation à un personnel qualifié. Faire réparer

l’appareil s’il a subi tout dommage, par exemple si la fiche ou le

cordon d’alimentation est endommagé, si du liquide a coulé ou

des objets sont tombés à l’intérieur de l’appareil, si l’appareil a été

exposé à la pluie ou à de l’humidité, si l’appareil ne fonctionne pas

normalement ou est tombé.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

(UL60065_03)

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE DÉCHARGE

ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À

L’HUMIDITÉ.

(UL60065_03)

Owner’s Manual

Tio1608-D

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifi-

cations not expressly approved by Yamaha may void your

authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accesso-

ries and/or another product use only high quality shielded

cables. Cable/s supplied with this product MUST be used.

Follow all installation instructions. Failure to follow instruc-

tions could void your FCC authorization to use this product

in the USA.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance that

your use of this product in a residential environment will not

result in harmful interference with other electronic devices.

This equipment generates/uses radio frequen

cies and, if not

installed and used

according to the instructions found in the

users manual, may cause interference harmful to the

operation of other electronic devices. Compliance with FCC

regulations does not guarantee that interference will not

occur in all installations. If this product is found to be the

source of interference, which can be determined by turning

the unit “OFF” and “ON”, please

try to eliminate the problem

by using one of the following measures:

locate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to co-axial type cable.

If these corrective measures do n

ot produce satisfactory

results, please contact the loca

l retailer authorized to

distribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Corporation of

America, Electronic Service Division, 6600 Orangethorpe

Ave, Buena Park, CA90620

The above statements apply ONLY to those products distrib-

uted by Yamaha Corporation of America or its subsidiari

es.

In Finland: Laite on liitettävä suojamaadoituskoskettimilla

varustettuun pistorasiaan.

In Norway: Apparatet må tilkoples jordet stikkontakt.

In Sweden: Apparaten skall anslutas till jordat uttag.

(class I hokuo)

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park,

Calif. 90620

Telephone : 714-522-9011

Type of Equipment : I/O RACK

Model Name : Tio1608-D

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received

including interference that may cause undesired operation.

See user manual i

nstructions if interference to radio reception

is suspected.

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA

(FCC DoC)

IMPORTANT NOTICE

FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in

accordance with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus

may not correspond with the coloured markings identifying

the terminals in your plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be

connected to the terminal in the plug which is marked by the

letter E or by the safet

y earth symbol or colored GREEN or

GREEN

-and-YELLOW.

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the

terminal which is marked with the letter L or coloured RED.

(3 wires)

이 기기는 가정용 (B 급) 전자파적합기기로서 주로

가정에서 사용하는 것을 목적으로 하며 , 모든

지역에서 사용할 수 있습니다.

(class b korea)

Owner’s Manual

Tio1608-D

Table of contents

Owner’s Manual

Tio1608-D

English

Table of contents

Included items ........................................................ 5

PRECAUTIONS...................................... 6

Introduction........................................ 8

Main features .......................................................... 8

Updating the firmware............................................ 8

Dante support......................................................... 8

Precautions when rackmounting............................. 8

Recessed Installation ............................................... 8

Device features.................................... 9

Front panel ............................................................. 9

Rear panel............................................................. 11

Connection methods ......................... 13

Quick Config (automatic setup) ............................ 13

Manual setup........................................................ 14

Head amp control ................................................. 14

Troubleshooting................................ 15

Troubleshooting ................................................... 15

How to read the indicators................ 16

Specifications .................................. 119

General Specifications ......................................... 119

Input Output Digital I/O Character ..................... 120

Dimensions ......................................................... 121

Model No.

Serial No.

(rear_en_01)

The model number, serial number, power requirements, etc., may be

found on or near the name plate, which is at the rear of the unit. You

should note this serial number in the space provided below and retain

this manual as a permanent record of your purchase to aid identifica-

tion in the event of theft.

Included items

• Owner's Manual (this document)

•Power cord

• Rubber feet ×4

Information for Users on Collection

and Disposal of Old Equipment

This symbol on the products,

packaging, and/or accompanying

documents means that used

electrical and electronic products

should not be mixed with

general household waste. For

proper treatment, recovery and

recycling of old products,

please take them to applicable collection points,

in accordance with your national legislation and

the Directives 2002/96/EC.

By disposing of these products correctly, you will

help to save valuable resources and prevent any

potential negative effects on human health and

the environment which could otherwise arise

from inappropriate waste handling.

For more information about collection and

recycling of old products, please contact your

local municipality, your waste disposal service or

the point of sale where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic

equipment, please contact your dealer or

supplier for further information.

[Information on Disposal in other Countries

outside the European Union]

This symbol is only valid in the European Union.

If you wish to discard these items, please contact

your local authorities or dealer and ask for the

correct method of disposal.

(weee_eu_en_01)

Owner’s Manual

Tio1608-D

PA_en_5 1/2

PRECAUTIONS

PLEASE READ CAREFULLY

BEFORE PROCEEDING

Please keep this manual in a safe place for

future reference.

WARNING

Always follow the basic precautions listed below to

avoid the possibility of serious injury or even death

from electrical shock, short-circuiting, damages, fire

or other hazards. These precautions include, but are

not limited to, the following:

Power supply/power cord

• Do not place the power cord near heat sources such as

heaters or radiators, and do not excessively bend or

otherwise damage the cord, place heavy objects on it, or

place it in a position where anyone could walk on, trip over,

or roll anything over it.

• Only use the voltage specified as correct for the device. The

required voltage is printed on the name plate of the device.

• Use only the supplied power cord/plug.

If you intend to use the device in an area other than in the

one you purchased, the included power cord may not be

compatible. Please check with your Yamaha dealer.

• Check the electric plug periodically and remove any dirt or

dust which may have accumulated on it.

• When setting up the device, make sure that the AC outlet

you are using is easily accessible. If some trouble or

malfunction occurs, immediately turn off the power switch

and disconnect the plug from the outlet. Even when the

power switch is turned off, as long as the power cord is not

unplugged from the wall AC outlet, the device will not be

disconnected from the power source.

• Remove the electric plug from the outlet when the device is

not to be used for extended periods of time, or during

electrical storms.

• Be sure to connect to an appropriate outlet with a protective

grounding connection. Improper grounding can result in

electrical shock, damage to the device(s), or even fire.

Do not open

• This device contains no user-serviceable parts. Do not open

the device or attempt to disassemble the internal parts or

modify them in any way. If it should appear to be

malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

Water warning

• Do not expose the device to rain, use it near water or in

damp or wet conditions, or place on it any containers (such

as vases, bottles or glasses) containing liquids which might

spill into any openings. If any liquid such as water seeps into

the device, turn off the power immediately and unplug the

power cord from the AC outlet. Then have the device

inspected by qualified Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

Hearing loss

• When turning on the AC power in your audio system, always

turn on the power amplifier LAST, to avoid hearing loss and

speaker damage. When turning the power off, the power

amplifier should be turned off FIRST for the same reason.

Fire warning

• Do not place any burning items or open flames near the

device, since they may cause a fire.

If you notice any abnormality

• If any of the following problems occur, immediately turn off

the power switch and disconnect the electric plug from the

outlet.

- The power cord or plug becomes frayed or damaged.

- Unusual smells or smoke are emitted.

- Some object has been dropped into the device.

- There is a sudden loss of sound during use of the device.

- Cracks or other visible damage appear on the device.

Then have the device inspected or repaired by qualified

Yamaha service personnel.

• If this device should be dropped or damaged, immediately

turn off the power switch, disconnect the electric plug from

the outlet, and have the device inspected by qualified

Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to

avoid the possibility of physical injury to you or

others, or damage to the device or other property.

These precautions include, but are not limited to, the

following:

Power supply/power cord

• When removing the electric plug from the device or an

outlet, always hold the plug itself and not the cord. Pulling by

the cord can damage it.

Location

• Do not place the device in an unstable position where it

might accidentally fall over and cause injuries.

• Do not block the vents. This device has ventilation holes at

the front/rear/sides to prevent the internal temperature from

becoming too high. In particular, do not place the device on

its side or upside down. Inadequate ventilation can result in

overheating, possibly causing damage to the device(s), or

even fire.

• Do not place the device in a location where it may come into

contact with corrosive gases or salt air. Doing so may result

in malfunction.

• Before moving the device, remove all connected cables.

• If the device is mounted in an EIA standard rack, carefully

read the section “Precautions when rackmounting” on page

8. Inadequate ventilation can result in overheating, possibly

causing damage to the device(s), malfunction, or even fire.

Table of contents

Owner’s Manual

Tio1608-D

English

Connections

• Before connecting the device to other devices, turn off the

power for all devices. Also, before turning the power of all

devices on or off, make sure that all volume levels are set to

the minimum. Failing to do so may result in electric shock,

hearing loss, or equipment damage.

Maintenance

• Remove the power plug from the AC outlet when cleaning

the device.

Handling caution

• Do not insert your fingers or hands in any gaps or openings

on the device (vents, ports, etc.).

• Avoid inserting or dropping foreign objects (paper, plastic,

metal, etc.) into any gaps or openings on the device (vents,

panel, etc.) If this happens, immediately turn off the power,

unplug the power cord from the AC outlet, and have the

device inspected by qualified Yamaha service personnel.

• Do not rest your weight on the device or place heavy objects

on it, and avoid use excessive force on the buttons, switches

or connectors to prevent injuries.

NOTICE

To avoid the possibility of malfunction/ damage to the

product, damage to data, or damage to other property,

follow the notices below.

Handling and maintenance

• Do not use the device in the vicinity of a TV, radio, stereo

equipment, mobile phone, or other electric devices.

Otherwise, the device, TV, or radio may generate noise.

• Do not expose the device to excessive dust or vibration, or

extreme cold or heat (such as in direct sunlight, near a

heater, or in a car during the day), in order to prevent the

possibility of panel disfiguration, unstable operation, or

damage to the internal components.

• Do not place vinyl, plastic or rubber objects on the device,

since this might discolor the panel.

• When cleaning the device, use a dry and soft cloth. Do not

use paint thinners, solvents, cleaning fluids, or chemical-

impregnated wiping cloths.

• Condensation can occur in the device due to rapid, drastic

changes in ambient temperature—when the device is

moved from one location to another, or air conditioning is

turned on or off, for example. Using the device while

condensation is present can cause damage. If there is

reason to believe that condensation might have occurred,

leave the device for several hours without turning on the

power until the condensation has completely dried out.

• The rubber feet included in this package can be attached to

the speaker to prevent slippage when it is to be used on a

slippery surface.

• Always turn the power off when the device is not in use.

Connectors

• XLR-type connectors are wired as follows (IEC60268

standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

Information

About this manual

• The illustrations and LCD screens as shown in this manual

are for instructional purposes only.

• The company names and product names in this manual are

the trademarks or registered trademarks of their respective

companies.

• Software may be revised and updated without prior notice.

European models

Purchaser/User Information specified in EN55103-2:2009.

Conforms to Environments: E1, E2, E3 and E4

Yamaha cannot be held responsible for damage caused

by improper use or modifications to the device.

Introduction

Owner’s Manual

Tio1608-D

Introduction

Thank you for purchasing the Yamaha Tio1608-D I/O rack.

The Tio1608-D is an I/O rack that features 16 channels of

analog inputs and 8 channels of analog outputs.

In order to take full advantage of this product's features, and

to enjoy years of trouble-free use, please read this

document before you begin using the product. After you

have read this document, please keep it in a safe place.

Main features

• Quick Config makes it easy to create a system based

on the Yamaha TF Series Digital Mixing Console

Simply install an NY64-D card into your TF series mixing

console, and then use Quick Config to create a system

using up to three Tio1608-D racks.

• Remote control of the built-in head amps

You can use a TF series mixing console or other

compatible device to control the built-in head amps.

• Combination jacks provide versatile connectivity

The analog inputs use combination jacks that allow for a

wide range of applications.

Updating the firmware

The firmware contained in this product can be updated to

take advantage of new features, feature improvements, and

bug fixes. The product uses two types of firmware.

• Main unit firmware

• Dante module firmware

Details about updating the firmware are available online.

http://www.yamahaproaudio.com/

For information about updating and setting up the console,

please refer to the firmware update guide available on the

website.

Dante support

This product uses the Dante digital audio network protocol

to send and receive audio signals. Dante is a protocol

developed by Audinate that is designed to deliver

multichannel audio signals at various sampling and bit

rates, as well as device control signals over a Gigabit

Ethernet network.

For information about Dante, please visit the Audinate

website.

http://www.audinate.com/

You can also find information about Dante and Dante-

compatible products on the Yamaha Pro Audio website.

http://www.yamahaproaudio.com/

Precautions when

rackmounting

This product is designed to function in environments with a

temperature of 0 to 40°C. If you install this product together

with multiple units of the same device or other devices in a

standard EIA rack, the heat produced by the devices may

raise the ambient temperature inside the rack enclosure to

the point where performance is affected. To ensure that the

heat produced by this product can be dissipated

appropriately, please ensure the following conditions when

rackmounting it.

• When mounting the unit in a rack with devices such as

power amplifiers that generate a significant amount of

heat, leave at least 1U of unused space between the unit

and the other device.

Additionally, install a ventilation panel in this unused

space or leave it open to ensure adequate cooling.

• To ensure sufficient airflow, leave the back of the rack

open and position it at least 10 centimeters from walls or

other surfaces.

If the back of the rack cannot be left open, install a

commercially available fan or similar ventilating option to

secure sufficient airflow.

If you install a fan kit, there may be cases in which closing

the back of the rack will produce a greater cooling effect.

Refer to the documentation included with the rack and/or

fan unit details.

Recessed Installation

If you want to recess the front panel surface of the device

from the front edge of the rack, you can adjust the position

of the rack mount brackets to recess the device by 50mm,

as shown in the illustration below.

NOTE

When updating this product's Dante module firmware, make sure

you also update the Dante module firmware contained in other

connected devices.

NOTE

When you install the brackets, use the same screws that you just

removed.

50 mm

Device features

Owner’s Manual

Tio1608-D

English

Device features

Front panel

1 [INPUT] jacks 1–16

Combination jacks that support both XLR and TRS

phone connectors. Use these jacks to connect mics

and instruments.

Nominal input level is -62 dBu to +10 dBu.

When connecting a cable that uses an XLR plug, make

sure you supply +48 V phantom power to any devices

that require it.

2 [+48V] indicators

These indicators light when +48 V phantom power is

turned on for the corresponding input channels. You

can use a compatible mixing console or other device

to turn phantom power on and off If the [+48V

MASTER] switch is turned off, no phantom power will

be supplied even if phantom power is turned on for

individual channels (although the +48V indicators will

still flash).

3 [OUTPUT +4dBu] jacks 1–8

These XLR-3-32 type balanced connectors deliver

analog output from the unit’s corresponding output

channels. Nominal output level is +4 dBu.

4 [STATUS INPUT] indicator

This indicator indicates the status of the signal being

input to the analog input jacks.

If the signal input to any channel reaches or exceeds

-34 dBFS, the indicator lights in green; if the signal

reaches or exceeds -3 dBFS, the indicator lights in red.

The indicator flashes in red if the input is muted, if the

system clock is being synced, or if there is a system

error.

5 [STATUS OUTPUT] indicator

If the signal level of any analog output jack reaches or

exceeds -34 dBFS, this indicator lights in green.

The indicator flashes in red if the output is muted, if

the system clock is being synced, or if there is a system

error.

6 [UNIT ID] switch

Determines the unit's identifier (i.e., unit ID) when

using Quick Config. When using multiple units, set a

unique ID (1–3) to each unit.

When not using Quick Config, this switch and the DIP

switches on the rear of the unit determine the ID.

(page 11)

Turn the unit off before changing the [UNIT ID] switch

position. If you move the switch while the unit is

turned on, the new switch position is not applied.

See "Connection methods" (page 13) for

information about Quick Config.

7 [QUICK CONFIG] switch

Turns Quick Config on and off.

When not using Quick Config, this switch and the DIP

switches on the rear of the unit determine the ID.

(page 11-12)

Turn the unit off before changing the [QUICK

CONFIG] switch position. If you move the switch

while the unit is turned on, the new switch position is

not applied.

See "Connection methods" (page 13) for

information about Quick Config.

ղձ մյնշոչպջռճ

NOTE

The PAD will be switched on or off internally when the analog

gain of the internal head amp is adjusted between +17dB and

+18dB. When using phantom power, noise may be generated

if there is a difference in the impedance between the hot and

cold of the device connected to an input jack.

Caution

• Make sure that phantom power is turned off unless it is

needed.

• When turning on phantom power, make sure that no

equipment other than phantom-powered devices such

condenser microphones are connected to the corresponding

[INPUT] jacks. Supplying phantom power to a device that

does not require it can damage the device.

• Do not connect or disconnect a device while phantom power

is being supplied to it. Doing so can damage the connected

device and the unit itself.

• To prevent damage to speakers, make sure that power

amplifiers and powered speakers are turned off when turning

phantom power on or off. We also recommend setting all

digital mixing console output controls to their minimum

settings when turning phantom power on or off. Sudden high-

volume sound caused by turning phantom power on or off

could damage equipment and hearing.

NOTICE

If this product's balanced outputs are connected to an

unbalanced audio source, a difference in ground potential may

result that could cause a malfunction. Make sure each device

has the same ground potential. The cable used to connect an

unbalanced device should be pin 1: ground, pin 3: cold.

Device features

Owner’s Manual

Tio1608-D

8 [SYSTEM] indicators

Indicate the status of the Tio1608-D.

During normal operation, the green indicator is lit

and the red indicator is off. When the unit is turned

on, if the green indicator is off and the red indicator is

lit or is flashing, an error has occurred.

9 [SYNC] indicators

Indicate the status of the unit's internal Dante clock

sync.

When the green indicator is lit, the unit is the clock

slave, and the clock is in sync. When the green

indicator is flashing, the unit is the clock master. When

the unit is turned on, the green indicator should either

light or flash; if the indicator is off, an error has

occurred.

0 [+48V MASTER] switch

Turns the unit's +48 V phantom power on and off. If

the [+48V MASTER] switch is off, no phantom power

is supplied to the input jacks even if phantom power

is turned on for individual inputs. In this case, the

+48V indicators for individual inputs will still light,

even though no phantom power will be supplied.

You can change the switch position while the unit is

turned on.

a Power indicator

Indicates whether the unit is turned on or off.

b Power switch

Turns the unit on and off.

NOTICE

Rapidly turning the unit on and off in succession can cause it to

malfunction. After turning the unit off, wait for about 6 seconds

before turning it on again.

Device features

Owner’s Manual

Tio1608-D

English

Rear panel

1 AC IN connector

Connect the included power cord. When connecting

to a power outlet, first connect the power cord to the

unit, then connect the power cord to the power

outlet.

2 [FAN] switch

Allows you to set the unit's internal cooling fan to run

at high or low speed. The switch is set at the factory to

[LOW], but as long as the unit is operated within the

specified ambient temperature range either the

[LOW] or [HIGH] setting can be used. The [HIGH]

setting is recommended if the ambient temperature is

high, if the unit is in direct sunlight (even if the

ambient temperature is within the specified operating

range), and in any situation in which fan noise is not

a problem. When mounting three or more units

without leaving space between each unit, set each

unit's fan speed to HIGH.

You can change the switch position while the unit is

turned on.

3 DIP switches

Determines the unit's start up mode.

Make sure that the unit is turned off before adjusting

the DIP switches. If you adjust the switches while the

unit is turned on, the new switch positions are not

applied.

The following information explains how the DIP

switch positions.

• Switch 1 and 2 (unit ID)

These DIP switches, along with the [UNIT ID] switch,

determine the unit's UNIT ID when Quick Config is

not used.

The UNIT ID is determined as follows.

When Quick Config is used, these switches are

disabled.

• Switch 3 (initialize mode)

This DIP switch is used to reset the unit to its factory

default settings.

After the unit is reset, it starts up using the system

mode that corresponds to the position of switches 7

and 8.

ձղճյնմ

Caution

Make sure the unit is turned off before connecting or

disconnecting the power cord.

Switch

position

[UNIT ID]

switch = 1

[UNIT ID]

switch = 2

[UNIT ID]

switch = 3

01 02 03

04 05 06

07 08 09

0A 0B 0C

Switch

position

Initialize mode

Initialize mode is off (unit will not be reset

when it is turned on)

Initialize mode is on (unit will be reset

when it is turned on)

1 2

Device features

Owner’s Manual

Tio1608-D

• Switch 4 (Dante SECONDARY port mode)

This switch determines the operating mode of the

[SECONDARY] Dante connector.

When Quick Config is used, these switches are

disabled.

• Switches 5 and 6 (IP address mode)

These switches determine how the unit's IP address is

set.

• Switches 7 and 8 (start up mode)

These switches determine how the unit starts up

during start up mode. When set to "refresh" mode,

the settings of the mixer are applied when the unit

starts up. When set to "resume" mode, the unit

returns to the same state as the last time it was used.

When Quick Config is used, the "normal operation"

mode settings are disabled.

4 [PRIMARY] and [SECONDARY] Dante connectors

etherCON CAT5 connector that connects the unit to a

Dante device, such as a NY64-D digital audio interface

card. When DIP switch 4 is set to the daisy-chain

connection position (i.e., up position), signals

received on one connector are sent out via the other

connector. When DIP switch 4 is set to the redundant

connection position (i.e., down position), the

[SECONDARY] connector functions as a backup and

carries the same signals as the [PRIMARY] connector. If

for some reason signals cannot be carried over the

[PRIMARY] connector (for example, because the cable

becomes damaged or disconnected, or because the

network switch malfunctions), the unit switches to

the [SECONDARY] connector.

5 [LINK/ACT] indicators

Indicate the status of the signals carried by the

[PRIMARY] and [SECONDARY] connectors. If an

indicator is flashing quickly, the corresponding

Ethernet cable is not connected properly.

6 [1G] indicators

Indicate the connection status of the PRIMARY and

SECONDARY connectors. If an indicator is lit, the

corresponding connector is connected to a Gigabit

Ethernet network.

NOTE

If switches 7 and 8 are set to the "update mode" or "diagnostic

mode" positions, the unit will not be reset.

Switch

position

[SECONDARY] connector operating

mode

Daisy chain connection

Redundant connection

NOTE

When the Switch 4 is set to "Redundant connection", the

head amp control function (page 14) is only available via

the [PRIMARY] Dante connector.

Switch

position

IP address mode

Auto (link local)

DHCP

Static IP Auto (192.168.0.ID)

Static IP Manual

The IP address is specified from an

external device such as R Remote V3.

Switch

position

Start up mode

Refresh mode (normal operation)

Resume mode (normal operation)

Update mode

5 6

7 8

Diagnostic mode

NOTE

• Update mode and diagnostic mode are used when

performing maintenance on the unit. Normally you will not

use these modes.

• Update mode and diagnostic mode can be enabled even

when using Quick Config. Normally you will not use these

modes.

NOTE

• To avoid electromagnetic interference, use shielded

twisted-pair (STP) cables that are rated at CAT5e or higher.

Use conductive tape or comparable means to make sure

that the metal parts of the cable plugs are electrically

connected to the STP cable shield.

• We recommend using RJ-45 plugs that are compatible with

Neutrik etherCON CAT5 connectors. You can also use

cables with standard RJ-45 plugs.

• The maximum length of cable that can be used varies

depending on the type of cable. When using CAT5e cables,

data can be sent between devices that are connected by up

to 100 m of cable.

Switch

position

Start up mode

7 8

Connection methods

Owner’s Manual

Tio1608-D

English

Connection methods

This section explains the different methods for connecting

the Tio1608-D to other Dante devices.

Quick Config (automatic setup)

When connecting the unit to a TF series mixing console,

Quick Config makes it easy to set up the unit automatically.

It allows you to connect up to three Tio1608-D units to one

TF series mixing console, and configures Dante network

settings and audio signal settings in one operation.

Tio1608-D procedure

1. With all the units turned off, set the DIP switches on

the rear panel to the up position.

2. Set the [QUICK CONFIG] switch on the front panel

to the [ON] position.

3. Set the [UNIT ID] switch on the front panel to the

desired position.

If you are using multiple Tio1608-D units, make sure

each unit has a unique UNIT ID setting.

4. Use Ethernet cables to connect the Tio1608-D to the

NY64-D card (installed in the TF series mixing

console) or to other Tio1608-D units in a daisy-

chain configuration, as shown below.

When using Quick Config, the units will operate the same

whether you connect the Ethernet cables to the [PRIMARY] or

[SECONDARY] Dante connector.

When connecting 3 units

5. Turn each device on.

TF series mixing console procedure

6. Display the console's SYSTEM SETUP  SLOT SETUP

screen, and confirm that Quick Config is enabled.

Now the TF series mixing console can recognize the

Tio1608-D units, and all Dante settings and input and output

patching settings will be configured automatically.

When the Quick Config button is displayed in white, Quick

Config is enabled. If the button is grayed out, click it. If you

cannot enable Quick Config, return to step

1 and confirm that

the Tio1608-D is configured properly.

NOTE

An NY64-D audio interface card (sold separately) is required to

connect a Tio1608-D to a TF series mixing console.

TF Series (NY64-D)

Tio1608-D UNIT ID=1

Tio1608-D UNIT ID=2

Tio1608-D UNIT ID=3

[PRIMARY] or

[SECONDARY]

connector

[PRIMARY]

connector

[PRIMARY]

connector

[SECONDARY]

connector

[PRIMARY] or

[SECONDARY]

connector

[SECONDARY]

connector

Connection methods

Owner’s Manual

Tio1608-D

7. To assign the Tio1608-D inputs to the TF series

mixing console, set the input select on the console's

INPUT screen to "SLOT".

8. Adjust the input gain and other settings as

necessary.

Quick config is now complete.

Settings configured by Quick Config

Quick Config applies the following settings.

• Dante settings

• Patching

Manual setup

You can configure your devices manually if you do not want

to use Quick Config.

Tio1608-D procedure

1. With the unit turned off, set the [QUICK CONFIG]

switch on the front panel to the [OFF] position.

2. Refer to the information on page 11 - 12 and set the

DIP switches to the desired positions.

3. Set the [UNIT ID] switch on the front panel to the

desired position.

4. Use Ethernet cables to connect the Tio1608-D to

your Dante device.

5. Turn each device on.

Dante settings

When using manual setup, use Dante Controller to

configure Dante settings.

Dante Controller is a computer program that you can use to

configure Dante network settings and audio signal patching

settings. It is available for download at the website below.

(Dante Controller v3.2.1 or later is compatible with

Tio1608-D.)

http://www.yamahaproaudio.com/

For information about Dante Controller, refer to the Dante

Controller documentation.

When using manual setup, you will need to use Dante

Controller to configure the following settings at a minimum.

(You can configure other settings as desired.)

• Input and output patching settings (Network View 

Routing)

• Clock master settings (Network View  Clock Status)

• Sampling frequency settings (Device View  Config)

Head amp control

You can use a Yamaha digital mixer or other device to

control the Tio1608-D head amp.

When the unit is connected to a TF series mixing console,

you can control the unit's head amp just as you would adjust

the console's head amp.

When using a CL or QL series digital mixer, you can control

or use the following parameters.

•HA gain

• +48 V phantom power on/off

• HPF on/off

• HPF frequency cutoff adjustment

• Mute off

• +48 V phantom power master on/off display

• Analog input level meter display

• Firmware version display

• Device identify

• Dante SYSTEM and SYNC indicator information

NOTE

You can use the menu in the console's INPUT screen to switch

the inputs selected for the current FADER BANK.

Word clock 48 kHz (slave), no pull up/down

Latency 0.5 ms

Encoding 24-bit PCM

SECONDARY port mode Daisy chain

Patching Refer to the table below

IP address Previous setting is used

NOTE

Quick Config does not configure analog input parameters.

Tio input TF input TF output Tio output

#1 ID 1, Input 1  Channel 1 AUX 1  ID 1, Output 1

ID 1, Input 2  Channel 2 : :

::AUX 6 ID 1, Output 6

ID 1, Input 16  Channel 16 Stereo L  ID 1, Output 7

Stereo R  ID 1, Output 8

#2 ID 2, Input 1  Channel 17 AUX 7  ID 2, Output 1

ID 2, Input 2  Channel 18 : :

AUX 12  ID 2, Output 6

ID 2, Input 16  Channel 32 Stereo L  ID 2, Output 7

Stereo R  ID 2, Output 8

#3 ID 3, Input 1  Channel 33 AUX 13  ID 3, Output 1

ID 3, Input 2  Channel 34 : :

::AUX 18 ID 3, Output 6

ID 3, Input 8  Channel 40 AUX 19  ID 3, Output 7

AUX 20  ID 3, Output 8

NOTE

• Even if only UNIT ID 2 or 3 is used, channels are patched as

shown above based on the UNIT ID number.

• After you have used Quick Config to configure the settings, you

can use Dante Controller to change the individual settings.

However, each time the Tio1608-D is turned on, Dante Controller

settings will be replaced by the Quick Config settings. For this

reason, we recommend that you turn Quick Config off if you are

using Dante Controller.

NOTE

When the Dante SECONDARY port mode (page 12) is set to

"Redundant connection", the head amp control function is only

available via the [PRIMARY] Dante connector. The [SECONDARY]

Dante connector is not available for this function.

Troubleshooting

Owner’s Manual

Tio1608-D

English

Troubleshooting

Issue Cause Solution

No power, power indicator does

not light

Power cord not connected.

Make sure the power cord is connected (page

11).

The [POWER] switch is turned off.

Set the [POWER] switch to the "on" position. If

you still cannot resolve the problem, please

contact your nearest Yamaha representative.

Unit is not receiving an input

signal

Cables not connected properly. Make sure all cables are connected properly.

Source device is not sending a

signal to the unit.

Output a signal from the source device and

confirm that the [STATUS INPUT] indicators

light.

Internal head amp gain is too low.

Adjust the internal head amp gain to an

appropriate level.

DIP switches are set to "refresh"

mode but device that controls the

Tio1608-D has not started up.

Start the device that will control the Tio1608-D

and send the settings to the Tio1608-D.

Input level too low

Condenser mic is connected.

Set the [+48V MASTER] switch to the "on"

position.

Use the device that controls the Tio1608-D to

turn on phantom power for the corresponding

channel.

Internal head amp gain is too low.

Adjust the internal head amp gain to an

appropriate level.

No sound heard

Cables not connected properly. Make sure all cables are connected properly.

DIP switches are set to "refresh"

mode but device that controls the

Tio1608-D has not started up.

Start the device that will control the Tio1608-D

and send the settings to the Tio1608-D.

[UNIT ID] switch or DIP switch

settings not applied

You changed the switch positions

while the unit was turned on.

Make sure the unit is turned off before

changing the switch positions.

How to read the indicators

Owner’s Manual

Tio1608-D

How to read the indicators

You can use the [SYSTEM] and [SYNC] indicators to confirm the unit's status.

The indicators can relay operational status, error status, and warnings.

Error status

If one of the following errors has occurred, the device will not operate. Until the error is resolved, the green SYSTEM indicator

will be turned off, and all indicators for all I/O channels will continue to flash.

In addition, certain errors will cause the red SYSTEM indicator to light or flash.

The following errors affect the settings or the hardware. However, the device will still be usable. The green SYSTEM indicator

will light, and all indicators for all I/O channels will work normally.

In addition, certain errors will cause the red SYSTEM indicator to light or flash.

[SYSTEM] Indicators Description Possible Solution

Off Flashes 2 times

Internal Dante error has occurred. The unit is malfunctioning. Please contact

your nearest Yamaha representative.

Off Flashes 3 times

MAC address setting is damaged and Dante

communication is not possible.

Off Lit

Duplicate UNIT ID was found. Make sure each UNIT ID is only used once

on the Dante network.

[SYSTEM] Indicators Description Possible Solution

Lit Flashing

The number of Dante transmit flows

exceeded the limit.

Reduce the number of flows by, for example,

using Dante Controller to change some of the

transmit flows to multicast.

Lit Flashes 2 times

Error occurred when communicating with the

head amp.

Turn the unit off and then on again. If this does

not resolve the problem, please contact your

nearest Yamaha representative.

Lit Flashes 3 times

Internal memory has been corrupted. If using [RESUME] mode, turn the unit off

and then on again. If this does not resolve

the problem, please contact your nearest

Yamaha epresentative.

Lit Lit

You changed the positions of the device

setting DIP switches, or changed the Dante

settings from Dante Controller. Therefore, the

positions of the device setting DIP switches

do not match the actual Dante settings.

If the Device Lock setting was enabled from

Dante Controller, disable the setting, or

check the device setting DIP switch

positions, and set them to accommodate the

current situation.

How to read the indicators

Owner’s Manual

Tio1608-D

English

Warnings

The indicators will light and/or flash as shown until the cause is resolved.

If the green [SYNC] indicator is unlit, the unit’s clock is unconfirmed.

If the green indicator is flashing, the unit is the clock master.

If the green indicator is lit, the unit is the clock slave and the clock is synchronized.

Information Message

The indicators will remain lit and/or flashing cyclically to report the status.

If the orange [SYNC] indicator is unlit, the unit is operating normally.

If the green [SYNC] indicator is unlit, the unit's clock is unconfirmed.

[SYNC] Indicators Description Possible Solution

Off Flashing

Clock settings are incorrect. Check the clock master and sampling

frequency settings of the Tio1608-D and

Dante Controller.

Off Flashes 2 times

Unit not connected to Dante network. Make sure the cables are not damaged and

that they are connected properly.

Off Flashes 3 times

Cable wiring is wrong; cannot find other

Dante devices.

Check the wiring of the Ethernet cables.

[SYNC] Indicators Description Possible Solution

Lit or flashing Lit

Device that is not Gigabit Ethernet

compatible is connected.

To use Dante to send and receive digital

audio, make sure your devices are Gigabit

Ethernet compatible.

Lit or flashing Flashing

When using a redundancy network,

[SECONDARY] connector is sending/

receiving audio.

Check the connections of the network

connected to the [PRIMARY] connector.

Lit or flashing Flashes 2 times

When using a redundancy network, error

was detected on the [SECONDARY]

connector.

Check the connections of the network

connected to the [SECONDARY] connector.

[SYNC] Indicators Description Possible Solution

Off Lit

Synchronizing on a Dante network. Please wait until started has completed or

until the unit has finished synchronization. It

may take up to 45 seconds for completion.

Waiting to receive setting data. If START UP MODE is set to REFRESH on

the Tio1608-D unit, the input/output will be

muted until the unit receives setting data after

it starts up.

Flashing Off

The unit is functioning correctly as the word

clock master.

The unit is operating as the word clock

master.

Lit Off

The unit is functioning correctly as the word

clock slave.

The unit is operating as the clock slave and

the clock is synchronized.

Bedienungsanleitung

Tio1608-D

Specifications

Owner’s Manual

Tio1608-D

119

EnglishDeutschFrançais

EspañolPortuguêsItaliano

Русский

Specifications

General Specifications

Output impedance of signal generator: 150ohms

Measured with another Tio1608-D through Dante network.

Frequency Response Fs = 44.1kHz or 48kHz, 20Hz-20kHz, refer to the nominal output level @1kHz

Total Harmonic Distortion Fs = 44.1kHz or 48kHz

* Total Harmonic Distortion is measured with a -18dB/octave filter @80kHz

Hum & Noise Fs = 48kHz, EIN: Equivalent Input Noise

* Hum & Noise are measured with A-weighting filter.

Dynamic Range Fs = 48kHz

* Dynamic Range are measured with A-weighting filter.

Crosstalk@1kHz

* Crosstalk is measured with a -30dB/octave filter @22kHz

Sampling Frequency

Power Requirements

AC Cable Length and Temperature Range

Dimensions (W x H x D) & Net weight

480(W) x 88(H) x 364(D) mm, 5.7kg

Input

Output RL Conditions Min. Typ. Max. Unit

INPUT1-16 OUTPUT 1-8 600Ω GAIN: +66dB. -1.5 0.0 0.5 dB

Input

Output RL Conditions Min. Typ. Max. Unit

INPUT1-16 OUTPUT 1-8 600Ω +4dBu@20Hz-20kHz, GAIN: +66dB. 0.1 %

600Ω +4dBu@20Hz-20kHz, GAIN: -6dB. 0.05 %

Input

Output RL Conditions Min. Typ. Max. Unit

INPUT1-16 OUTPUT 1-8 600Ω Rs=150Ω, GAIN: +66dB. -128

EIN

dBu

-62 dBu

600Ω Rs=150Ω, GAIN: -6dB. -84 -80 dBu

all Inputs OUTPUT 1-8 600Ω Rs=150Ω, GAINs: -6dB

Master fader at nominal level and all INPUT 1-16 in

faders at nominal level.

Measured with TF5 (or TF3,TF1) through Dante.

-70 dBu

- OUTPUT 1-8 600Ω Residual output noise, STEREO master off.

Measured with TF5 (or TF3,TF1) through Dante.

-88 dBu

Input

Output RL Conditions Min. Typ. Max. Unit

INPUT1-16 OUTPUT 1-8 600Ω AD + DA, GAIN: -6dB. 108 dB

- OUTPUT 1-8 600Ω DA Converter 112 dB

from/to

to/from Conditions Min. Typ. Max. Unit

INPUT n INPUT (n-1) or (n+1) INPUT1-16

adjacent inputs, GAIN: -6dB.

-100 dB

OUTPUT n OUTPUT (n-1) or (n+1) OUTPUT 1-8, input to output -100 dB

Conditions Min. Typ. Max. Unit

External Clock Frequency Range 44.1kHz / 48kHz -200 +200 ppm

+4.1667%/+0.1%/-0.1%/-4.0% to all of the above -200 +200 ppm

Conditions Min. Typ. Max. Unit

Power Requirements 100-240V 50/60Hz 50 W

Heat Dissipation 100-240V 50/60Hz 43.5 kcal/h

Conditions Min. Typ. Max. Unit

AC Cable Length 2.5 m

Temperature Range Operating temperature range 0 40 °C

Storage temperature range -20 60 °C

Specifications

Owner’s Manual

Tio1608-D

120

Input Output Digital I/O Character

Analog input characteristics

Analog output characteristics

Digital input/output specifications

* The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access

the Yamaha website then download the manual file.

* Der Inhalt dieser Bedienungsanleitung gilt für die neuesten technischen Daten zum Zeitpunkt der Veröffentlichung. Um die

neueste Version der Anleitung zu erhalten, rufen Sie die Website von Yamaha auf und laden Sie dann die Datei mit der

Bedienungsanleitung herunter.

* Le contenu de ce mode d’emploi s’applique aux dernières caractéristiques techniques connues à la date de publication du

manuel. Pour obtenir la version la plus récente du manuel, accédez au site Web de Yamaha puis téléchargez le fichier du

manuel concerné.

* El contenido de este manual se aplica a las últimas especificaciones según la fecha de publicación. Para obtener el último

manual, acceda al sitio web de Yamaha y descargue el archivo del manual.

* O conteúdo deste manual se aplica às especificações mais recentes a partir da data de publicação. Para obter o manual

mais recente, acesse o site da Yamaha e faça o download do arquivo do manual.

* Il contenuto del presente manuale si applica alle ultime specifiche tecniche a partire dalla data di pubblicazione. Per ottenere

la versione più recente del manuale, accedere al sito Web Yamaha e scaricare il file corrispondente.

* В содержании данного руководства приведены последние на момент публикации технические характеристики.

Для получения последней версии руководства посетите веб-сайт корпорации Yamaha и загрузите файл с

руководством.

Input

Terminals

GAIN

Actual Load

Impedance

For Use With

Nominal

Input Level

Connector

balanced /

Unbalanced

Sensitivity

*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain.

Nominal Max. before clip

INPUT1-16 +66dB 7.5kΩ 50-600Ω Mics

or 600Ω Lines

-82dBu

(61.6μV)

-62dBu

(0.616mV)

-42dBu

(6.16mV)

Combo Jack

(XLR-3-31 type

TRS phone

)

*2. 1: GND, 2: HOT, 3: COLD

*3. Tip: HOT, Ring: COLD, Sleeve: GND

Balanced

-6dB -10dBu

(245mV)

+10dBu

(2.45V)

+30dBu

(24.5V)

In these specifications, 0dBu = 0.775Vrms.

+48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.

Output Terminals

Actual Sourcez

Impedance

For Use With

Nominal

Output Level

Connector

balanced /

Unbalanced

Nominal Max. before clip

OUTPUT 1-8 75Ω 600Ω Lines +4dBu

(1.23 V)

+24dBu

(12.3 V)

XLR-3-32 type

*1. 1: GND, 2: HOT, 3: COLD

Balanced

In these specifications, 0dBu = 0.775Vrms.

Terminal Format Data length Level Audio Connector

Primary / Secondary Dante 24 or 32bit 1000BASE-T 16ch (Tio1608-D to other devices)

8ch (Other devices to Tio1608-D)

etherCON Cat5e

Страница загружается...

Yamaha TIO1608-D, Tio1608 Инструкция по применению

Похожие модели бренда

Модели других брендов