Yamaha HTR-6260 Инструкция по применению

HTR-6260

AV Receiver

OWNER’S MANUAL

U

Caution-i En

• Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert you to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle

is intended to alert you to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers)

that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided plug

does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or when

unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing

is required when the apparatus has been damaged in any

way, such as power-supply cord or plug is damaged, liquid

has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

IMPORTANT SAFETY INSTRUCTIONS

Note to CATV system installer:

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the NEC that

provides guidelines for proper grounding and, in

particular, specifies that the cable ground shall be

connected to the grounding system of the building, as

close to the point of cable entry as practical.

FCC INFORMATION (for US customers)

1 IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifications

not expressly approved by Yamaha may void your authority,

granted by the FCC, to use the product.

2 IMPORTANT:

When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3NOTE:

This product has been tested and found to comply with

the requirements listed in FCC Regulations, Part 15 for Class “B”

digital devices. Compliance with these requirements provides a

reasonable level of assurance that your use of this product in a

residential environment will not result in harmful interference with

other electronic devices.

This equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the users

manual, may cause interference harmful to the operation of other

electronic devices.

Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product is

found to be the source of interference, which can be determined by

turning the unit “OFF” and “ON”, please try to eliminate the

problem by using one of the following measures:

Relocate either this product or the device that is being affected by

the interference.

Utilize power outlets that are on different branch (circuit breaker or

fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change the

lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type of

product. If you can not locate the appropriate retailer, please

contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe

Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products distributed by

Yamaha Corporation of America or its subsidiaries.

CAUTION

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Caution-ii En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place – away from direct sunlight, heat sources, vibration,

dust, moisture, and/or cold. Allow ventilation space of at least

30 cm on the top, 20 cm on the left and right, and 20 cm on

the back of this unit.

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury. Yamaha

will not be held responsible for any damage resulting from use

of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

17 Be sure to read the “Troubleshooting” section on common

operating errors before concluding that this unit is faulty.

18 Before moving this unit, press AMAIN ZONE ON/OFF

to set this unit to the standby mode, and disconnect the AC

power plug from the wall outlet in the main room and Zone2.

19 VOLTAGE SELECTOR (Asia and General models only)

The VOLTAGE SELECTOR on the rear panel of this unit

must be set for your local main voltage BEFORE plugging

into the AC wall outlet. Voltages are:

.......AC 110/120/220/230–240 V, 50/60 Hz (General model)

.......................... AC 220/230–240 V, 50/60 Hz (Asia model)

20 The batteries shall not be exposed to excessive heat such as

sunshine, fire or like.

21 Excessive sound pressure from earphones and headphones can

cause hearing loss.

22 When replacing the batteries, be sure to use batteries of the

same type. Danger of explosion may happen if batteries are

incorrectly replaced.

Caution: Read this before operating your unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

As long as this unit is connected to the AC wall outlet,

it is not disconnected from the AC power source even

if you turn off this unit by

A

MAIN ZONE ON/

OFF. In this state, this unit is designed to consume a

very small quantity of power.

FOR CANADIAN CUSTOMERS

To prevent electric shock, match wide blade of plug to

wide slot and fully insert.

This Class B digital apparatus complies with Canadian

ICES-003.

POUR LES CONSOMMATEURS CANADIENS

Pour éviter les chocs électriques, introduire la lame la

plus large de la fiche dans la borne correspondante de

la prise et pousser jusqu’au fond.

Cet appareil numérique de la classe B est conforme à

la norme NMB-003 du Canada.

IMPORTANT

Please record the serial number of this unit in the space

below.

MODEL:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

1 En

English

INTRODUCTION

APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Features.................................................................... 2

About this manual................................................... 3

Supplied accessories................................................ 3

Part names and functions....................................... 4

Front panel ................................................................. 4

Rear panel .................................................................. 5

Front panel display..................................................... 6

Remote control........................................................... 7

Quick start guide.....................................................8

L

Preparing remote control ....................................... 9

Installing batteries in the remote control ................... 9

Using the remote control............................................ 9

Connections ...........................................................10

Placing speakers....................................................... 10

Connecting speakers ................................................ 11

Information on jacks and cable plugs ...................... 13

Connecting a TV monitor or projector .................... 14

Connecting other components ................................. 15

Connecting an external amplifier............................. 16

Using REMOTE IN/OUT jacks............................... 17

Connecting a Yamaha iPod universal dock or

Bluetooth™ wireless audio receiver.................... 17

Using the VIDEO AUX jacks on the front panel .... 17

Connecting the FM and AM antennas ..................... 18

Connecting the power cable..................................... 18

Turning this unit on and off ..................................... 18

Optimizing the speaker setting for your

listening room (YPAO) .....................................19

Using Auto Setup..................................................... 19

When an error message is displayed during

measurement ........................................................ 21

When a warning message is displayed after

measurement ........................................................ 21

Playback.................................................................22

Basic procedure........................................................ 22

Using the SCENE function ...................................... 22

Muting audio output temporarily (MUTE).............. 23

Adjusting high/low frequency sound

(tone control) ....................................................... 23

Enjoying pure hi-fi sound ........................................ 23

Using your headphones............................................ 23

Displaying input signal information ........................ 24

Changing information on the front panel display .... 24

Using the sleep timer ............................................... 24

Enjoy the sound field programs .......................... 25

Selecting sound field programs................................ 25

Enjoying unprocessed input sources

(Straight decoding mode) .................................... 28

Enjoying sound field programs without surround

speakers (Virtual CINEMA DSP) ....................... 28

Enjoy sound field programs with headphones

(SILENT CINEMA™) ........................................ 28

Using CINEMA DSP 3D mode ............................... 28

FM/AM tuning ......................................................29

Tuning in to the desired FM/AM station

(Frequency tuning) .............................................. 29

Registering FM/AM stations and tuning in

(Preset tuning)...................................................... 29

XM

®

Satellite Radio tuning

(U.S.A. model only) ........................................... 31

Connecting XM Mini-Tuner Home Dock ............... 31

Activating XM Satellite Radio ................................ 31

XM Satellite Radio

®

operations ............................. 32

Registering XM Satellite Radio channels............... 33

Displaying the XM Satellite Radio™ information .. 34

SIRIUS Satellite Radio™ tuning

(U.S.A. model only)........................................... 35

Connecting the SiriusConnect™ tuner .................... 35

Activating SIRIUS Satellite Radio™ subscription.. 35

SIRIUS Satellite Radio™ operations...................... 35

Registering the SIRIUS Satellite Radio™

channels ............................................................... 37

Setting the Parental Lock......................................... 38

Displaying the SIRIUS Satellite Radio™

information .......................................................... 39

Using iPod™.......................................................... 40

Controlling iPod™................................................... 40

Using Bluetooth™ components ........................... 42

Pairing the Bluetooth™ wireless audio receiver

and your Bluetooth™ component........................ 42

Playback of the Bluetooth™ component ................. 42

Setting the option menu for each input source

(OPTION menu) ............................................... 43

OPTION menu items ............................................... 43

Outputting a video signal input from another

input source during reproducing a multi-channel

audio signal.......................................................... 45

Editing surround decoders/sound field

programs ........................................................... 46

Selecting a decoder used with a sound field

program................................................................ 46

Setting sound field parameters................................. 46

Sound field parameters ............................................ 46

Operating various settings for this unit

(Setup menu) ..................................................... 50

Basic operation of the setup menu ........................... 51

Speaker Setup .......................................................... 51

Sound Setup ............................................................. 53

Function Setup ......................................................... 54

DSP Parameter ......................................................... 56

Memory Guard......................................................... 56

Using multi-zone configuration ........................... 57

Connecting Zone2.................................................... 57

Controlling Zone2.................................................... 58

Controlling other components with the remote

control................................................................ 59

Setting remote control codes.................................... 59

Resetting all remote control codes........................... 59

Advanced setup..................................................... 60

Troubleshooting.................................................... 61

General..................................................................... 61

HDMI™................................................................... 64

Tuner (FM/AM) ....................................................... 64

XM Satellite Radio (U.S.A. model only)................ 65

SIRIUS Satellite Radio (U.S.A. model only) .......... 66

Remote control......................................................... 67

iPod™ ...................................................................... 68

Bluetooth™.............................................................. 68

Auto Setup (YPAO)................................................. 69

Glossary ................................................................. 71

Sound field program information ....................... 73

Information on HDMI™...................................... 74

Additional information ........................................ 75

About the HDMI™ control function ....................... 75

Using the HDMI™ control function........................ 75

Specifications......................................................... 76

Index ...................................................................... 77

(at the end of this manual)

Contents

INTRODUCTION

PREPARATION

BASIC OPERATION

ADVANCED OPERATION

APPENDIX

List of remote control codes...................................i

2 En

INTRODUCTION

■ Built-in 7-channel power amplifier

• Minimum RMS Output Power (1 kHz, 0.9% THD, 8 Ω)

• FRONT L/R: 90 W + 90 W

• CENTER: 90 W

• SURROUND L/R: 90 W + 90 W

• SURROUND BACK L/R: 90 W + 90 W

■ Speaker/Preout outputs

• Speaker jacks (7-channel), preout output jacks (7.1-

channel)

■ Input/Output terminals

Input terminals

• HDMI input x 4

• Audio/Visual input

[Audio] Digital input (coaxial) x 2, digital input

(optical) x 2, analog input x 2

[Video] Component video x 2, composite video x 4

• Audio input (analog) x 2

• Dock input x 1

• V-AUX input

[Audio] Analog x 1, stereo mini jack x 1

[Video] Composite video x 1

Output terminals

• Monitor output

[Audio/Video] HDMI x 1

[Video] Component video x 1, composite video x 1

• Audio/Visual output

[Audio] Analog x 1

[Video] Composite video x 1

• Audio output

Analog x 1

• Zone2 output

Analog x 1

Other terminals

Remote input x 1, Remote output x 1

Trigger output x 1

■ Proprietary Yamaha technology for the

creation of sound fields

• CINEMA DSP 3D

• Compressed Music Enhancer mode

• Virtual CINEMA DSP

• SILENT CINEMA

■ Digital audio decoders

• Dolby TrueHD, Dolby Digital Plus

• DTS-HD Master Audio, DTS-HD High Resolution

Audio, DTS Express

• Dolby Digital, Dolby Digital EX

• DTS, DTS 96/24, DTS-ES Matrix 6.1,

DTS-ES Discrete 6.1

• Dolby Pro Logic, Dolby Pro Logic II, Dolby Pro Logic IIx

• DTS NEO:6

• Neural Surround (U.S.A. model only)

• DSD

■ Radio tuners

• FM/AM tuning capability

• XM Satellite Radio tuning capability, using XM Mini-

Tuner and Home Dock, sold separately (U.S.A. model

only)

•

SIRIUS Satellite Radio tuning capability, using

SiriusConnect tuner, sold separately (U.S.A. model

only)

■ HDMI™

(High-Definition Multimedia Interface)

• HDMI interface for standard, enhanced or high-

definition video as well as multi-channel digital audio

– Automatic audio and video synchronization (lip sync)

information capability

– Deep Color video signal (30/36 bit) transmission

capability

– “x.v.Color” video signal transmission capability

– High refresh rate and high resolution video signals

capability

– High definition digital audio format signals capability

• Analog video to HDMI digital video up-conversion

(composite video → HDMI, component video →

HDMI) capability for monitor out

• Analog video input up-scaling for HDMI digital video

output 480i or 480p → 720p, 1080i or 1080p

■ DOCK terminal

• DOCK terminal to connect a Yamaha iPod universal

dock (such as YDS-11, sold separately) or Bluetooth

wireless audio receiver (such as YBA-10, sold

separately)

■ Automatic speaker setup features

• “YPAO” (Yamaha Parametric Room Acoustic

Optimizer) for automatically optimizing speaker

outputs suitable for listening environments

■ Other features

• 192-kHz/24-bit D/A converter

• OSD (on-screen display) menus that allow you to

optimize this unit to suit your individual audiovisual

system

• Pure Direct mode for pure hi-fi sound for all sources

• Adaptive dynamic range controlling capability

• Scene function that allows you to change input sources

and sound field programs with one key

• Sleep timer

• Multi-zone function

Features

3 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

Manufactured under license from Dolby Laboratories.

Dolby, Pro Logic and the double-D symbol are trademarks of Dolby

Laboratories.

Manufactured under license under U.S. Patent No’s:

5,451,942;5,956,674;5,974,380;5,978,762;6,226,616;6,487,535 &

other U.S. and worldwide patents issued & pending. DTS is a

registered trademark and the DTS logos, Symbol, DTS-HD and DTS-

Neural Surround

™

name and related logos are trademarks owned

by Neural Audio Corporation.

iPod™

“iPod” is a trademark of Apple Inc., registered in the U.S. and other

countries.

Bluetooth

™

Bluetooth is a registered trademark of Bluetooth SIG and is used by

Yamaha in accordance with a license agreement.

“HDMI,” the “HDMI” logo and “High-Definition Multimedia

Interface” are trademarks, or registered trademarks of HDMI

Licensing LLC.

x.v.Color™

“x.v.Color” is a trademark of Sony Corporation.

“SILENT CINEMA” is a trademark of Yamaha Corporation.

SIRIUS, XM and all related marks and logos are trademarks of Sirius

available in Alaska and Hawaii.

Check that you received all of the following parts.

• Remote control

• Batteries (2) (AAA, R03, UM-4)

• Optimizer microphone

• AM loop antenna

• Indoor FM antenna

About this manual

• y indicates a tip for your operation.

• Some operations can be performed by using either the keys on the front panel or the ones on the remote control. In case the key names differ between

the front panel and the remote control, the key name on the remote control is given in parentheses.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of

differences between the manual and product, the product has priority.

• “AMAIN ZONE ON/OFF” or “hHDMI 1” (example) indicates the name of the parts on the front panel or the remote control. Refer to the

attached sheet or “Part names and functions” on page 4 for the information about each position of the parts.

• ☞ indicates the page describing the related information.

Supplied accessories

4 En

A MAIN ZONE ON/OFF

Switches this unit between on and off (see page 18).

B PHONES jack

For plugging headphones (see page 23).

C ZONE2 ON/OFF

Switches the zone function on and off (see page 58).

D ZONE2 CONTROL

Enables operation of a receiver set in Zone2, including input

source switching, volume control and tuner operation, with the

main amplifier or remote control after this key is pressed.

E INFO

Changes information display screens on the front panel display

(see page 24).

F MEMORY

Registers FM/AM stations as preset stations (see page 30) or

XM/SIRIUS channels as preset channels (see page 33).

G PRESET l / h

Selects an FM/AM preset station (see page 30) or an XM/

SIRIUS preset channel (see page 33).

H FM/AM (CATEGORY l / h)

Changes the tuner bands between FM and AM.

Select a channel category for a XM/SIRIUS.

I TUNING/CH l / h

Changes FM/AM frequencies or XM/SIRIUS tuner channels.

J SCENE

Switches between linked sets of input sources and sound field

programs (see page 22).

K TONE CONTROL

Adjusts high-frequency/low-frequency output of speakers/

headphones (see page 22).

L PROGRAM l / h

Changes sound field programs (see page 25).

M STRAIGHT

Changes a sound field program to straight decoding mode

(see page 28).

N PURE DIRECT

Changes mode to Pure Direct mode (see page 23). This key

lights up when Pure Direct mode is on.

O INPUT l / h

Selects an input source (see page 22).

P OPTIMIZER MIC jack

For connecting the supplied optimizer microphone and adjusting

output characteristics of speakers (see page 19).

Q VOLUME control

Controls the volume of this unit (see page 22).

R VIDEO (VIDEO AUX) jack

For connecting the video output cable of a camcorder or game

console (see page 17).

S AUDIO L/R (VIDEO AUX) jack

For connecting the audio output cable of a camcorder or game

console (see page 17).

T PORTABLE (VIDEO AUX) jack

For connecting the audio output cable of a portable music player

(see page 17).

U Front panel display

Displays information on this unit (see page 6).

V HDMI THROUGH

Lights up during pass-through output of an HDMI signal input

to this unit while this unit is on standby (see page 54).

Part names and functions

Front panel

l

h

CATEGORY

PRESET

TUN./CH

SLEEP

HDMI

AV

AUDIO

ZONE2

TRANSMIT

CODE SET

a

b

e

f

g

h

k

l

m

n

p

q

t

u

c

d

i

j

r

s

o

HDMI 1-4

Selects HDMI inputs 1 through 4.

AV 1-6

Selects AV inputs 1 through 6.

AUDIO 1/2

Selects AUDIO inputs 1 and 2.

V-AUX

Selects the V-AUX jack on the front panel of this

unit.

[A]/[B]

To control external components using the

sExternal component operation

keys separately from operations of this unit

(see page 59).

DOCK

Selects a Yamaha iPod universal dock/Bluetooth

wireless audio receiver connected to the DOCK

terminal.

TUNER

Selects the FM/AM tuner.

SIRIUS

Selects a SiriusConnect tuner as an input source.

XM

Selects an XM tuner as an input source.

MULTI

Selects a signal input from the MULTI CH

INPUT jack on the rear panel as an input source.

FM

Switches a band between FM and AM.

AM

(CATEGORY l / h)

Select a channel category for a XM/

SIRIUS.

MEMORY

Presets radio stations.

PRESET k / n

Selects a preset station.

TUN./CH k / n

Changes FM/AM frequencies or

XM/SIRIUS tuner channels.

Cursors k / n / l / h

Select menu items displayed on the

front panel display or on a video

monitor, or change settings.

ENTER

Confirms a selected item.

RETURN

Returns to the previous screen or

ends the menu display.

8 En

When you use this product for the first time, perform setup following the steps below. See the related pages for details on

operations and settings.

Prepare speakers, DVD player, cables, and other items

necessary for setup.

For example, prepare the following items for setting up a

5.1-channel sound system.

y

• Prepare two magnetically shielded speakers (for front). The priority of

the requirement of other speakers is as follows:

1 Two surround speakers

2 One center speaker

3 One (or two) surround back speaker(s)

• If your video monitor is a CRT, we recommend that you use magnetically

shielded speakers.

Place your speakers in the room and connect them to this

unit.

y

• This unit has a YPAO (Yamaha Parametric Room Acoustic Optimizer)

that automatically optimizes this unit based on room acoustic

characteristics (audio characteristics of the speakers, speaker positions,

and room acoustics, etc.).

You can enjoy good balanced sound without special knowledge by using

the YPAO technology (see page 19).

Connect your TV, DVD player, or other components.

Connect the power cable and turn on this unit.

Select the component connected in the step 3 as an input

source and start playback.

y

• This unit supports the SCENE function that changes the input source and

sound field program at one time. Four scenes are preset for different

purposes for Blu-ray disc, DVD and CD, and you can select from a scene

from those just by pressing a remote control key. See page 22 for details.

Quick start guide

Step 1: Prepare items for setup

Requirements qty.

Speakers Front speaker 2

Center speaker 1

Surround speaker 2

Active subwoofer 1

Speaker cable 5

Subwoofer cable 1

Reproduction component such as DVD player 1

Video monitor such as TV 1

Video cable or HDMI cable 2

Audio cable 2

Front right speaker

Subwoofer

Surround left speaker

Surround right speaker

Front left speaker

Video monitor

Center speaker

Components

(such as DVD player)

Step 2: Set up your speakers

• Placing speakers ☞P. 10

• Connecting speakers ☞P. 11

Step 3: Connect your components

• Connecting a TV monitor or projector ☞P. 14

• Connecting other components ☞P. 15

• Connecting a multi-format player or

an external decoder ☞P. 16

• Connecting an external amplifier ☞P. 16

• Connecting a Yamaha iPod universal dock or

Bluetooth wireless audio receiver ☞P. 17

• Connecting the FM and AM antennas ☞P. 18

• Connecting an XM Mini-Tuner Home Dock ☞P. 31

• Connecting a SiriusConnect tuner ☞P. 35

Step 4: Turn on the power

• Connecting the power cable ☞P. 18

• Turning this unit on and off ☞P. 18

Step 5: Select the input source and start

playback

• Basic procedure ☞P. 22

• Selecting sound field programs ☞P. 25

9 En

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

PREPARATION

1 Take off the battery compartment cover.

2 Insert the two supplied batteries (AAA, R03,

UM-4) according to the polarity markings (+

and –) on the inside of the battery

compartment.

3 Snap the battery compartment cover back

into place.

Notes

• Change all batteries if you notice the following conditions:

– the operation range of the remote control narrows

– the transmit indicator does not flash or is dim

• Do not use old batteries together with new ones.

This may shorten the life of the new batteries or cause old batteries

to leak.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Specification of batteries may be

different even though they look the same.

• If you find leaking batteries, discard the batteries immediately,

taking care not to touch the leaked material. If the leaked material

comes into contact with your skin or gets into your eyes or mouth,

rinse it away immediately and consult a doctor. Clean the battery

compartment thoroughly before installing new batteries.

• Dispose of the old batteries correctly in accordance with your local

regulations.

• If the remote control is without batteries for more than 2 minutes,

or if exhausted batteries remain in the remote control, the contents

of the memory may be cleared. In such a case, install new batteries

and set the remote control code.

The remote control transmits a directional infrared ray. Be

sure to aim the remote control directly at the remote

control sensor on this unit during operation.

Notes

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following conditions:

– places of high humidity, such as near a bath

– places of high temperatures, such as near a heater or stove

– places of extremely low temperatures

– dusty places

y

• You can operate external components with this remote control by setting

the remote control code. See page 59 for details.

Preparing remote control

Installing batteries in the remote

control

1

3

2

Using the remote control

30 30

Remote control sensor window

within 6 m (20 ft)

10 En

This unit supports up to 7.1-channel surround. We recommend the following speaker layout in order to obtain the

optimum surround effect.

7.1-channel speaker layout

6.1-channel speaker layout

5.1-channel speaker layout

■ Front left and right speakers (FL and FR)

The front speakers are used for the front channel sounds

(stereo sound) and effect sounds. Place these speakers at

an equal distance from the ideal listening position. When

using a screen, the appropriate top positions of the

speakers are about 1/4 of the screen from the bottom.

■ Center speaker (C)

The center speaker is for the center channel sounds

(dialog, vocals, etc.). Place it halfway between the left and

right speakers. When using a TV, place the speaker just

above or just under the center of the TV with the front

surfaces of the TV and the speaker aligned. When using a

screen, place it just under the center of the screen.

■ Surround left and right speakers (SL and SR)

The surround speakers are used for effect and surround

sounds.

Place them at the rear left and rear right facing the

listening position.

To obtain a natural sound flow in the 5.1-channel speaker

layout, place them slightly further back than in the 7.1-

channel speaker layout.

■ Surround back left and right speakers (SBL

and SBR) / Surround back speaker (SB)

The surround back left and right speakers are used for rear

effect sounds. Place them at the rear of the room facing the

listening position at least 30 cm away from each other,

ideally at the same distance as that between the front left

and right speakers.

In the 6.1-channel speaker layout, surround back left and

right channel sound signals are mixed down and output

from the single surround back speaker.

In the 5.1-channel speaker layout, surround back left and

right channel sound signals are output from the surround

left and right speakers.

■ Subwoofer (SW)

The subwoofer speaker is used for bass sounds and low-

frequency effect (LFE) sounds included in Dolby Digital

and DTS signals. Use a subwoofer with a built-in

amplifier, such as the Yamaha Active Servo Processing

Subwoofer System. Place it exterior to the front left and

right speakers facing slightly inward to reduce reflections

from a wall.

Connections

Placing speakers

60˚

30˚

SBR

SBL

FL

FR

C

SL

SR

80˚

SL

SW

30 cm (12 in) or more

60˚

30˚

SB

FL

FR

C

SL

SR

80˚

SL

SW

60˚

30˚

FL

FR

C

SL

SR

80˚

SL

SW

Speaker channels

11 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

■ Presence left and right speakers (PL and PR)

The presence speakers supplement the sound from the

front speakers with extra ambient effects produced by the

sound field programs (see page 25). We recommend that

you use the presence speakers especially for the CINEMA

DSP sound field programs. To use the presence speakers,

connect the speakers to EXTRA SP terminals and then set

“Extra SP Assign” to “Presence” (see page 51).

When you connect speakers, connect them to the respective terminals as follows, according to your speaker layout.

y

• Connect optional presence speakers or Zone2 speakers (see page 57) to the EXTRA SP jacks.

• You can connect up to two subwoofers. When two subwoofers are connected, the same sound is output from them.

■ 7.1-channel (with presence speakers)

■ 6.1-channel (when using the Multi-zone

function)

■ 5.1-channel (when using the Multi-zone

function)

FR

PRPL

C

FL

0.5 to 1 m (1 to 3 ft)0.5 to 1 m (1 to 3 ft)

1.8 m

(6 ft)

1.8 m

(6 ft)

Connecting speakers

Speakers Jacks on this unit

a Front speaker L FRONT (L)

b Front speaker R FRONT (R)

c Center speaker CENTER

d Surround speaker L SURROUND (L)

e Surround speaker R SURROUND (R)

f Surround back speaker L SURROUND

BACK/BI-AMP (L)

g Surround back speaker R SURROUND

BACK/BI-AMP (R)

h Subwoofer 1 SUBWOOFER 1

i Subwoofer 2 (optional) SUBWOOFER 2

j Presence speaker L (optional) EXTRA SP (L)

k Presence speaker R (optional) EXTRA SP (R)

SUBWOOFER

FRONT

CENTER

SURROUND

SURROUND BACK/

BI-AMP

SPEAKERS

EXTRA SP

ZONE2/PRESENCE

1

2

R.BAC

K

S

UBWOOFER

N

PUT

AUDI

O

UT

Z

O

NE2

O

U

T

F

R

O

NT

S

URROUND

S

UR. BAC

K

P

RE

OUT

C

ENTE

R

D

MI 3

HDMI

4

X.

SPEAKERS

C

ENTER

e d

b

a

k

j

c

g f

h i

Speakers Jacks on this unit

a Front speaker L FRONT (L)

b Front speaker R FRONT (R)

c Center speaker CENTER

d Surround speaker L SURROUND (L)

e Surround speaker R SURROUND (R)

f Surround back speaker SURROUND

BACK/BI-AMP (L)

h Subwoofer 1 SUBWOOFER 1

i Subwoofer 2 (optional) SUBWOOFER 2

j Zone2 speaker L (optional) EXTRA SP (L)

k Zone2 speaker R (optional) EXTRA SP (R)

Speakers Jacks on this unit

a Front speaker L FRONT (L)

b Front speaker R FRONT (R)

c Center speaker CENTER

d Surround speaker L SURROUND (L)

e Surround speaker R SURROUND (R)

h Subwoofer 1 SUBWOOFER 1

i Subwoofer 2 (optional) SUBWOOFER 2

j Zone2 speaker L (optional) EXTRA SP (L)

k Zone2 speaker R (optional) EXTRA SP (R)

12 En

Connections

■ Connecting to the FRONT, CENTER,

SURROUND and SURROUND BACK/BI-AMP

terminals

1 Remove approximately 10 mm (0.4 in) of

insulation from the end of each speaker

cable and then twist bare wires of the cable

together so that they will not cause a short

circuits.

2 Loosen the knob, insert the twisted bare

wires into the hole, and then tighten the

knob.

■ Connecting to the EXTRA SP terminals

1 Press down the tab and insert the bare end of

the speaker cable into the hole in the terminal.

y

• You can connect the presence speakers (see page 11) or the speakers in

the second zone (Zone2) (see page 57) to EXTRA SP terminals.

2 Release the tab to secure the wire.

You can connect speakers that support bi-amplification

connections to this unit. To connect the speakers via a bi-

amp connection, connect them to the FRONT jacks and

SURROUND BACK/BI-AMP terminals as illustrated.

To enable the bi-amp connection, connect the power cable

to the wall outlet, display the ADVANCED SETUP menu

and set “BI AMP” to “ON” (see page 60).

Connecting the speaker cable

Caution

• A speaker cable is a pair of insulated cables running side by side in general. One of the cables is colored differently

or striped to indicate a polarity. Connect one end of the colored/striped cable to the “+” (red) terminal of this unit

and the other end to that of your speaker, and connect one end of the other cable to the “–” (black) terminal of this

unit and the other end to that of your speaker.

• Before connecting the speakers, be sure to disconnect the power cable.

• Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit and/or

speakers. If the circuit shorts out, “CHECK SP WIRES!” appears on the front panel display when this unit is turned

on.

• Use magnetically shielded speakers. If images on the monitor are still distorted even when you use the magnetically

shielded speakers, place the speakers away from the monitor.

• Use speakers with an impedance of 6-ohm or larger. Set speaker impedance in “ADVANCED SETUP” before

connecting the speakers (see page 60).

Connecting the banana plug (Except Russia

and Asia models)

Tighten the knob, and then insert the banana plug into

the end of the terminal.

10 mm (0.4 in)

1

2

3

Red: positive (+)

Black: negative (–)

Banana plug

Using bi-amplification connections

Caution

Before making bi-amplification connections, remove any

brackets or cables that connect a woofer with a tweeter.

Refer to the instruction manuals of speakers for details.

When not making bi-amplification connections, make

sure that the brackets or cables are connected before

connecting the speaker cables.

Red: positive (+)

Black: negative (–)

SURROUND BACK/

BI-AMP

FRONT

Front speakers

Right Left

This unit

13 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

This unit has the following input and output jacks. Use jacks and cables appropriate for components that you are

connecting.

■ Audio jacks

■ Video jacks

■ Video/audio jacks

y

• We recommend that you use a commercially available 19-pin HDMI

cable no longer than 5 meters (16 feet) with the HDMI logo printed on it.

• When you connect this unit to a component with a DVI jack, an HDMI/

DVI-D cable is required.

• You can check error information on HDMI connections (see page 74).

Information on jacks and cable plugs

Jack and cables Description

AUDIO jacks To transmit conventional analog

left and right audio signals. Use

stereo pin cables. Connect red

plugs to red jacks (R) and white

plugs to white jacks (L).

COAXIAL jacks To transmit coaxial digital audio

signals. Use pin cables for digital

audio signals.

OPTICAL jacks To transmit optical digital audio

signals. Use optical fiber cables for

optical digital audio signals.

Jack and cables Description

VIDEO jacks To transmit conventional

composite video signals. Use video

pin cables.

COMPONENT VIDEO

jacks

To transmit component video

signals that include luminance (Y),

chrominance blue (PB) and

chrominance red (PR) components.

Use component video cables.

AUDIO

L

R

(white)

(red)

COAXIAL

C

(orange)

OPTICAL

O

VIDEO

V

(yellow)

PR

PB

Y

COMPONENT

VIDEO

P

B

Y

P

R

(red)

(blue)

(green)

Jack and cables Description

HDMI jacks To transmit digital video and

digital audio signals. Use HDMI

cables.

A video signal input to this unit is output from the

output terminals in MONITOR OUT for the same kind

of signal as the input signal.

For example, if a VCR with a composite output signal

and a DVD player with a COMPONENT VIDEO

output signal are connected, connect both VIDEO jack

and COMPONENT VIDEO jack in MONITOR OUT

to the video monitor.

If an HDMI input compatible monitor is connected, this

unit automatically converts an analog signal that is

input from a video input terminal to a digital video

signal, and then output it from the HDMI OUT jack.

HDMI

VIDEO

COMPONENT

VIDEO

Y

PB

PR

HDMI

VIDEO

COMPONENT

VIDEO

Y

PB

PR

Input Output

Repeat Converted

14 En

Connections

Connect a video monitor such as a TV or projector to an output terminal of this unit. You can select one of the following

three types according to the input signal format supported by the video monitor.

Note

• Make sure that this unit and video monitor are unplugged from the AC wall outlets.

■ To connect an HDMI video monitor

■ To connect component video monitor

Note

• Only video signals input from this unit via the component input terminal

are output from the component output terminal.

■ To connect composite video monitor

Note

• Only video signals input from this unit via the composite video input

terminal are output from the composite video output terminal.

To output sound of a TV from this unit, make connection

between the AV input 1-6 and an audio output terminal.

If the TV supports an optical digital output, we

recommend that you use the AV input 1. Connecting to the

AV input 1 allows you to switch an input source to the AV

input 1 with a just a single key operation using the SCENE

function (see page 22).

Connecting a TV monitor or projector

Jacks on components Jacks on this unit

a HDMI input HDMI OUT

Jacks on components Jacks on this unit

b Component video output MONITOR OUT

(COMPONENT VIDEO)

Jacks on components Jacks on this unit

c Video input (composite) MONITOR OUT (VIDEO)

HDMI

VIDEO

M

O

NIT

O

R

OUT

PR

PB

Y

COMPONENT

VIDEO

OUT

ANTENNA

UNBAL.

FM

G

N

D

AM

HDMI

1

(

B

D

/

DVD

)

HDMI

2

HD

M

I

N

OU

T

RI

GG

ER

O

UT

12V

0

.1

A

MAX.

REM

O

TE

HDMI

V

a

c

b

P

B

YP

R

TV, or projector

Outputting sound of a TV from this unit

OPTICAL

(

TV

)

AV 1

P

R

P

B

Y

AV

2

CO

AXIAL

A

V

3

(

CD

)

CO

AXIA

L

O

PTI

C

A

L

A

V

4

AV

5

AV

6

AV

OU

T

A

U

DI

O

1

A

U

D

VIDE

O

UNBAL

.

F

M

G

ND

A

M

P

R

P

B

Y

O

Digital output

(optical)

TV, or projector

15 En

Connections

English

INTRODUCTION

ADDITIONAL

INFORMATION APPENDIX

PREPARATION

BASIC

OPERATION

ADVANCED

OPERATION

This unit has input and output terminals for respective input and output sources. You can reproduce sound and movies

from input sources selected with the front panel display or remote control.

Note

• Make sure that this unit and other components are unplugged from the AC wall outlets.

■ Audio and video player / Set-top box

y

• Input sources in parentheses are recommended to connect to the respective jacks. If a component is compatible with the SCENE function, you can switch

the input source to that component with a single key operation using the SCENE function (see page 22).

• You can change the name of the input source displayed on the front panel display or the OSD on the video monitor as necessary (see page 55).

• See page 57 on how to use ZONE2 OUT jacks.

Connecting other components

Output jacks on the connected external component

Input sources/jacks of this unit

External

components

Signals Output jacks

External component

with HDMI output

Audio/Video HDMI output HDMI 1 (BD/DVD) HDMI 1

HDMI 2 HDMI 2

HDMI 3 HDMI 3

HDMI 4 HDMI 4

External component

with component video

output

Audio Optical digital output AV 1 (TV) OPTICAL

Video Component video output COMPONENT VIDEO

Audio Coaxial digital output AV 2 COAXIAL

Video Component video output COMPONENT VIDEO

External component

with composite video

output

Audio Coaxial digital output AV 3 (CD) COAXIAL

Video Composite output VIDEO

Audio Optical digital output AV 4 OPTICAL

Video Composite output VIDEO

Audio Analog audio output AV 5 AUDIO

Video Composite output VIDEO

Audio Analog audio output AV 6 AUDIO

Video Composite output VIDEO

COMPONENT

VIDEO

P

R

P

B

Y

OPTICAL

(

TV

)

AV

1

AV 2

COAXIAL

AV 3

(

CD

)

COAXIAL

OPTICAL

AV 4

AV 5

AV 6

AV

OUT

AUDIO1

AUDIO2

FRONT

SURROUND

SUR.BACK

SUBWOOFER

MULTI CH INPUT

AUDIO

OUT

VIDEO

HDMI 1

(

BD/DVD

)

HDMI 2

HDMI 3

HDMI 4

MONITOR

OUT

TRIGGER

OUT

CENTER

S

IRIU

S

XM

D

OCK

ZO

O

HDMI

ANTENNA

UNBAL.

FM

G

N

D

AM

VIDE

O

IN

O

U

T

MONITOR OUT

TRIGGER OUT

1

2

V

0.1

A

MAX

.

FR

O

N

T

P

R

P

B

Y

REM

O

T

E

C

OMPONEN

T

VIDEO

OUT

Audio / video input (AV 1-6) Audio / video output (AV OUT)

Audio input (AUDIO 1-2)

HDMI input

(HDMI 1-4)

Audio output

(AUDIO OUT)

Multi channel audio input (MULTI CH)

16 En

Connections

■ Audio player

y

• We recommend connecting the coaxial digital output terminal of a CD player to the AV3 jack.

This unit has 8 sets of input jacks (FRONT L/R,

CENTER, SURROUND L/R, SUR. BACK and

SUBWOOFER) to input multi-channel analog sound

signals. If your playback component, such as a DVD

player or SACD player, has multi-channel analog output

capability, you can enjoy up to 7.1-channel multi-channel

sound. To output multi-channel sound, connect the audio

output jacks of your playback component to the MULTI

CH INPUT jacks of this unit, and set the input source of

this unit to “MULTI CH.” For details on how to change

input sources, see page 22.

Notes

• When you select “MULTI CH” as the input source, the digital sound field

processor is automatically disabled.

• Since this unit does not redirect signals input at the MULTI CH INPUT

jacks to accommodate for missing speakers, connect at least a 5.1-

channel speaker system when using this feature.

• When the input source is switched to “MULTI CH,” images input from a

component connected to “AV1-6” or “V-AUX” (see page 45). If your

DVD player does not support multi-channel digital output, connect it to

these input jacks.

This unit has more than enough power for any home use.

However, if you want to add more power to the speaker

output or if you want to use another amplifier, connect an

external amplifier to the PRE OUT jacks. Each PRE OUT

jack outputs the same channel signals as the

corresponding SPEAKERS terminals.

Note

• When you make connections to the PRE OUT jacks, do not make any

connections to the SPEAKERS terminals.

a FRONT PRE OUT jacks

Front channel output jacks.

b SURROUND PRE OUT jacks

Surround channel output jacks.

c SUR. BACK PRE OUT jacks

Surround back output jacks. When you only connect one

external amplifier for the surround back channel, connect it to

the single SUR. BACK jack.

y

• To output surround back channel signals at these jacks, set “Sur.

Back” to any parameter except “None” (see page 52).

d CENTER PRE OUT jack

Center channel output jack.

e SUBWOOFER PRE OUT 1/2 jacks

Connect a subwoofer with a built-in amplifier.

Output jacks on the connected external component

Input sources/jacks of this unit

External components Output jacks

External component with optical digital

output

Optical digital output AV 1 (TV) OPTICAL

AV 4 OPTICAL

External component with coaxial digital

output

Coaxial digital output AV 2 COAXIAL

AV 3 (CD) COAXIAL

External component with analog audio

output

Analog audio output AV 5 AUDIO

AV 6 AUDIO

AUDIO 1 AUDIO

AUDIO 2 AUDIO

About audio/video output terminals

Among the analog audio and analog video signals input to this unit via input terminals, the audio/video signals of the

selected input sources are output from the AV OUT jack and AUDIO OUT jack. An HDMI input signal,

COMPONENT VIDEO input signal or digital audio input signal cannot be output.

When using the AV OUT jack: connect an external component to the composite or analog audio terminal.

When using the AUDIO OUT jack: connect an external component to the analog audio terminal.

Connecting a multi-format player or an

external decoder

FRONT

SURROUND

SUR.BACK

SUBWOOFER

MULTI CH INPUT

CENTER

LRLR LR

Surround

back out

Surround

out

Front out

Subwoofer out

Center out

Multi-format player/External decoder

(7.1-channel output)

Connecting an external amplifier

FRONT

SURROUND

SUR. BACK

SUBWOOFER

PRE OUT

CENTER

1

2

abc d

e

Страница загружается...

Yamaha HTR-6260 Инструкция по применению

Похожие модели бренда