DeWalt DCMPS567 Инструкция по эксплуатации

DCMPS567

Final page size: A5 (148mm x 210mm)

ENGLISH

English (original instructions) 5

Pусский (перевод соригинала инструкции) 20

Англійська (оригінальні інструкції) 40

DEWALT

Fig. A

Fig. B

Fig. C

Fig. E

Fig. G

Fig. D

Fig. F

Fig. H

1112

17 25

14 13

Fig. I

Fig. K

Fig. M

Fig. J

Fig. L

Fig. N

122

Fig. O

Fig. R

Fig. P

Fig. Q

ENGLISH

WARNING: To reduce the risk of injury, read the

instructionmanual.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.

CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.

Denotes risk of electricshock.

Denotes risk offire.

EC-Declaration of Conformity

Machinery Directive

Pole Saw

DCMPS567

DEWALT

declares that these products described under

Technical Data are in compliance with:

2006/42/EC, EN 62841-1:2015; EN ISO 11680-1:2011, 2000/14/

EC , Annex V DEKRA Certification B.V., Meander 1051 / P.O. Box

5185 6825 MJ ARNHEM / 6802 ED ARNHEM Netherlands

Notified Body ID No.: 0344

LPA (measured sound pressure level) 81.9 dB(A)

LWA (guaranteed sound power) 95.0 dB(A)

These products also comply with Directive 2014/30/EU and

2011/65/EU. For more information, please contact

DEWALT

the following address or refer to the back of themanual.

The undersigned is responsible for compilation of the technical

file and makes this declaration on behalf of

DEWALT

Markus Rompel

Vice President of Engineering, PTE-Europe

DEWALT

, Richard-Klinger-Straße 11,

D-65510, Idstein, Germany

22.07.2019

The vibration and/or noise emission level given in this

information sheet has been measured in accordance with a

standardised test given in EN ISO 11680-1:2011 and may be

used to compare one tool with another. It may be used for a

preliminary assessment ofexposure.

WARNING: The declared vibration and/or noise emission

level represents the main applications of the tool. However

if the tool is used for different applications, with different

accessories or poorly maintained, the vibration and/or

noise emission may differ. This may significantly increase

the exposure level over the total workingperiod.

An estimation of the level of exposure to vibration and/or

noise should also take into account the times when the tool

is switched off or when it is running but not actually doing

the job. This may significantly reduce the exposure level

over the total workingperiod.

Identify additional safety measures to protect the operator

from the effects of vibration and/or noise such as: maintain

the tool and the accessories, keep the hands warm

(relevant for vibration), organisation of workpatterns.

DCMPS567

Voltage VDC 18

Battery type Li-Ion

Bar Length cm 20

Maximum Chain Speed (no-load) m/s 6,5

Maximum Cutting Length cm 15

Oil Capacity ml 115

Weight (without battery pack) kg 4

Noise values and vibration values (triax vector sum)

according to EN ISO 11680-1:2011.

LPA (emission sound pressure level) dB(A) 81,9

LWA (sound power level) dB(A) 92,0

K (uncertainty for the given sound level) dB(A) 3

Vibration emission value a

= m/s2<2,5

Uncertainty K = m/s21,5

Congratulations!

You have chosen a

DEWALT

tool. Years of experience, thorough

product development and innovation make

DEWALT

one of the

most reliable partners for professional power toolusers.

Technical Data

POLE SAW

DCMPS567

ENGLISH

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electricshock.

f ) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

influence of drugs, alcohol or medication. A moment

of inattention while operating power tools may result in

serious personalinjury.

b ) Use personal protective equipment. Always wear eye

protection. Protective equipment such as a dust mask,

non-skid safety shoes, hard hat or hearing protection used

for appropriate conditions will reduce personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off-position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energising power tools that have the switch on

invitesaccidents.

d ) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached

to a rotating part of the power tool may result in

personalinjury.

e ) Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be

caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-relatedhazards.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions,

illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below

may result in electric shock, fire and/or seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTUREREFERENCE

The term “power tool” in the warnings refers to your mains-

operated (corded) power tool or battery-operated (cordless)

powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which

may ignite the dust orfumes.

c ) Keep children and bystanders away while operating

a power tool. Distractions can cause you to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of

electricshock.

b ) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if

your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electricshock.

Batteries Chargers/Charge Times (Minutes)

Cat # VDC Ah Weight (kg) DCB104 DCB107 DCB112 DCB113 DCB115 DCB118 DCB132 DCB119

DCB546 18/54 6.0/2.0 1.05 60 270 170 140 90 60 90 X

DCB547 18/54 9.0/3.0 1.46 75* 420 270 220 135* 75* 135* X

DCB548 18/54 12.0/4.0 1.44 120 540 350 300 180 120 180 X

DCB181 18 1.5 0.35 22 70 45 35 22 22 22 45

DCB182 18 4.0 0.61 60/40** 185 120 100 60 60/40** 60 120

DCB183/B 18 2.0 0.40 30 90 60 50 30 30 30 60

DCB184/B 18 5.0 0.62 75/50** 240 150 120 75 75/50** 75 150

DCB185 18 1.3 0.35 22 60 40 30 22 22 22 X

DCB187 18 3.0 0.54 45 140 90 70 45 45 45 90

DCB189 18 4.0 0.54 60 185 120 100 60 60 60 120

*Date code 201811475B or later

**Date code 201536 or later

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce risk of injury:

• Before any use, be sure everyone using this unit reads

and understands all safety instructions and other

information contained in this manual.

• Save these instructions and reviewfrequently.

WARNING: When using electric gardening

appliances, basic safety precautions should always be

followed to reduce risk of fire, electric shock, and personal

injury, including thefollowing.

1 . Avoid Dangerous Environment – Don’t use appliances in

damp or wetlocations.

2 . Don’t Use InRain.

3 . Keep Children Away – All visitors should be kept at a

distance from workarea.

4 . Dress Properly – Do not wear loose clothing or jewelry.

They can be caught in moving parts. Use of rubber gloves

and substantial footwear is recommended when working

outdoors. Wear protective hair covering to contain longhair.

5 . Use Safety Glasses – Always use face or dust mask if

operation isdusty.

6 . Use Right Appliance – Do not use appliance for any job

except that for which it isintended.

7 . Don’t grasp the exposed cutting blades or cutting edges

when picking up or holding the appliance.

8 . Don’t Force Appliance – It will do the job better and

with less likelihood of a risk of injury at the rate for which it

wasdesigned.

9 . Don’t Overreach – Keep proper footing and balance at

alltimes.

contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation orburns.

e ) Do not use a battery pack or tool that is damaged or

modified. Damaged or modified batteries may exhibit

unpredictable behaviour resulting in fire, explosion or risk

ofinjury.

f ) Do not expose a battery pack or tool to fire or

excessive temperature. Exposure to fire or temperature

above 130 °C may causeexplosion.

g ) Follow all charging instructions and do not charge

the battery pack or tool outside the temperature

range specified in the instructions. Charging

improperly or at temperatures outside the specified range

may damage the battery and increase the risk offire.

6) Service

a ) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This

will ensure that the safety of the power tool ismaintained.

b ) Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized serviceproviders.

h ) Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe

injury within a fraction of asecond.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must berepaired.

c ) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the

power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrainedusers.

e ) Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardoussituation.

h ) Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpectedsituations.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may create

a risk of injury andfire.

c ) When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

ENGLISH

Always use head protection when operating the pole saw

overhead. Falling debris can result in serious personalinjury.

SPECIFIC SAFETY RULES

WARNING: Some dust contains chemicals known to

State of California to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

• compounds in fertilizers,

• compounds in insecticides, herbicides andpesticides,

• arsenic and chromium from chemically

treatedlumber.

To reduce your exposure to these chemicals, wear

approved safety equipment such as dust masks that are

specially designed to filter out microscopicparticles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction

activities. Wear protective clothing and wash exposed

areas with soap and water. Allowing dust to get into your

mouth, eyes, or lay on the skin may promote absorption of

harmfulchemicals.

WARNING: Use of this tool can generate and/

or disburse dust, which may cause serious and

permanent respiratory or other injury. Always use

approved respiratory protection appropriate for the dust

exposure. Direct particles away from face andbody.

CAUTION: Wear appropriate personal hearing protection

during use. Under some conditions and duration of use,

noise from this product may contribute to hearingloss.

Before Operating Pole Saw

• For safe operation, read and understand all instructions

before using the pole saw. Follow all safety instructions.

Failure to follow all safety instructions listed below, can result

in serious personalinjury.

• Watch what you are doing. Use common sense. Do not

operate pole saw when you aretired.

• Use pole saw for cutting tree branches only. Do not use

pole saw for purposes not intended. Do not use for cutting

otheritems.

• Only well-instructed adults should operate pole saw.

Never allow children tooperate.

• Do not allow children or untrained individuals to use

thisunit.

• Wear the following safety gear when operating pole saw:

ʵ heavy-duty gloves

ʵ steel-toed safety footwear with non-skid soles

ʵ safety glasses, goggles or face screen

ʵ safety hard hat

ʵ ear mufflers or ear plugs

ʵ face or dust mask (if working in dusty areas)

• Wear heavy long pants and boots. Do not wear loose

fitting clothing, short pants, jewelry of any kind, or gobarefoot.

• Secure long hair so it is above shoulder level to prevent

entanglement in any movingparts.

10 . Stay Alert – Watch what you are doing. Use common sense.

Do not operate appliance when you aretired.

11 . Disconnect Appliance – Remove the battery when not in

use, before servicing, when changing accessories such as

blades, and thelike.

12 . Store Idle Appliances Indoors – When not in use,

appliances should be stored indoors in dry, and high or locked-

up place – out of reach ofchildren.

13 . Maintain Appliance With Care – Keep cutting edge sharp

and clean for best performance and to reduce the risk of injury.

Follow instructions for lubricating and changing accessories.

Inspect appliance power source periodically, and if damaged,

have it repaired by an authorized service facility. Keep handles

dry, clean, and free from oil andgrease.

14 . Check Damaged Parts – Before further use of the appliance,

a guard or other part that is damaged should be carefully

checked to determine that it will operate properly and perform

its intended function. Check for alignment of moving parts,

binding of moving parts, breakage of parts, mounting, and

any other condition that may affect its operation. A guard

or other part that is damaged should be properly repaired

or replaced by an authorized service center unless indicated

elsewhere in thismanual.

SAVE THESE INSTRUCTIONS

WARNING - Do not operate near electrical power

lines. The unit has not been designed to provide

protection from electric shock in the event of contact with

overhead electric lines, Consult local regulations for safe

distances from overhead electric power lines and ensure

that the operating position is safe and secure before

operating the saw chain polepruner.

• Keep all parts of the body away from the saw chain. Do

not remove cut material or hold material to be cut when

blades are moving. Make sure the switch is off when

clearing jammed material. Blades coast after turn off.

A moment of inattention while operating the pole saw may

result in serious personalinjury.

• Carry the pole saw by the handle with the saw chain

stopped. When transporting or storing the pole saw always

fit the saw chain device cover. Proper handling of the pole saw

will reduce possible personal injury from the sawchain.

• Hold the power tool by insulated gripping surfaces only,

because the cutter blade may contact hidden wiring.

A saw chain contacting a “live” wire may make exposed

metal parts of the tool “live” and could give the operator an

electricshock.

• Do not use the pole saw in bad weather conditions,

especially when there is a risk of lightning. This decreases

the risk of being struck bylightning.

• Always use two hands when operating the pole saw.

Hold the pole saw with both hands to avoid lossofcontrol.

ENGLISH

GENERAL SAFETY RULES

DANGER: Shock Hazard. Serious injury or death from

electrocution if power lines are contacted. Never use near

any electrical source, wires, or powerlines.

WARNING: For safe operation read and understand

owner’s manual. Wear face shield (and/or safety glasses)

and hard hat to protect against falling debris. Always have

a clear work area, retreat path, and be aware of limb/

branch location to avoid falling limbs and debris. Keep

bystanders 15 m away when operating saw. To reduce the

risk of electric shock do not use on wet surfaces. Do not

expose to rain. Storeindoors.

• To protect yourself from falling branches do not stand directly

under the branch or limb being cut. This unit should not be held at

an angle over

60°

from groundlevel.

• Keep the handles dry, clean, and free ofoil.

• Before you start the unit, make sure the chain is not contacting

anyobject.

• Make sure the cutting chain has stopped before setting the

unitdown.

Service

• Tool service must be performed only by qualified repair

personnel. Service or maintenance performed by unqualified

personnel could result in a risk of injury. Refer to the

Maintenance section of thismanual.

• When servicing a tool, use only identical replacement

parts. Follow instructions in the Maintenance section of

this manual. Use of unauthorized parts or failure to follow

maintenance instructions may create a risk of electric shock

orinjury.

Guard Against Kickback

WARNING: KICKBACK may occur when the nose or tip of

the guide bar touches an object, or when the wood closes

in and pinches the saw chain in the cut. Tip contact in

some cases may cause a lightning fast reverse reaction,

kicking the guide bar up and back towards the operator.

• Inspect pole saw before each use and after dropping or other

impacts. Ensure there are no significant defects ordamage.

Do Not Operate Pole Saw:

ʵ while under the influence of alcohol, medication, ordrugs.

ʵ in rain or in damp or wetareas.

ʵ where highly flammable liquids or gases arepresent.

ʵ if pole saw is damaged, adjusted incorrectly, or not fully

and securelyassembled.

ʵ if trigger does not turn pole saw on and off. Chain must

stop moving when you release trigger. Have faulty switch

replaced by authorized service center. See Accessories

underMaintenance.

ʵ while in ahurry.

ʵ while in a tree or on aladder.

ʵ while on aerial booms, buckets orplatforms.

ʵ during high wind or stormingweather.

• Before cutting, always provide the following:

ʵ clear work area

ʵ secure footing

ʵ planned retreat path from falling limbs

• Inspect tree before trimming. Make allowance for branches to

fall freely to theground.

• Do not use your pole saw to fellsaplings.

While Operating Pole Saw

DANGER: To reduce the risk of electric shock

do no use on wet surfaces. Do not expose to rain.

Storeindoors.

DANGER: Avoid Unintentional Starting – with battery

installed, don’t carry appliance with with finger on switch.

Be sure switch is off when installingbattery.

• Stay alert. Use common sense while operating theunit.

• Keep work area clean. Cluttered areas inviteinjuries.

• Always remove battery from pole saw when finished cutting or

when leftunattended.

• Keep children, animals and bystanders at least 15 m away

from pole saw. Only pole saw user should be in workarea.

• Do not use the pole saw to cut downtrees.

• Do not grasp the exposed saw chain when picking up or

holding the polesaw.

• Grip pole saw securely - one hand on the pole, the other on

thehandle.

• Keep finger off trigger until ready to makecut.

• Before starting pole saw, make sure chain is not

touchinganything.

• Keep all parts of body away from chain when pole saw

isrunning.

• Do not force pole saw while cutting. Apply light pressure.

It will do the job better and safer at the rate for which it

wasintended.

• Carry pole saw from one place to another:

ʵ with battery removed,

ʵ fingers off/away from trigger,

ʵ by holding pole at balance point, and

ʵ with guide bar and chain to rear and with

scabbardattached.

• Do not cut small brush and saplings with the pole saw. Slender

matter may catch in the chain and be whipped toward you.

This could also pull you offbalance.

• Do not operate in poorlighting.

• Keep firm footing and balance. Do not overreach.

Overreaching can result in loss of balance or exposure to

hotsurfaces.

• Keep all parts of your body away from any movingpart.

• Do not, under any circumstance, use any attachment or

accessory on this product, which was not provided with the

product, or identified as appropriate for use with this product

in this instructionmanual.

ENGLISH

• Reduced Kickback Chain, designed with a contoured depth

gauge and guard link which deflect kickback force and allow

wood to gradually ride into the cutter. A reduced-kickback

chain is a chain which has met kickback performance

requirements when tested on the representative sample of

chainsaws.

Pole Saw Names and Terms

• Drive Sprocket or Sprocket - The toothed part that drives

the sawchain.

• Guide Bar - A solid railed structure that supports and guides

the sawchain.

• Guide Bar Scabbard - Enclosure fitted over guide bar to

prevent tooth contact when saw is not inuse.

• Kickback - The backward or upward motion, or both of the

guide bar occurring when the saw chain near the nose of the

top area of the guide bar contacts any object such as a log or

branch, or when the wood closes in and pinches the saw chain

in thecut.

• Reduced Kickback Chain - A chain that complies with

the kickback performance requiremens. (when tested on a

representative sample of chainsaws.)

• Reduced Kickback Guide Bar - A guide bar which has been

demonstrated to reduce kickbacksignificantly.

• Replacement Saw Chain - A chain that complies with

kickback performance requirements when tested with specific

chain saws. It may not meet performance requirements when

used with othersaws.

• Saw Chain - A loop of chain having cutting teeth, that cut the

wood, and that is driven by the motor and is supported by the

guidebar.

• Spiked Bumper (Spike) - The pointed tooth or teeth for

use when pruning to pivot the saw and maintain position

whilesawing.

• Switch - A device that when operated will complete or

interrupt an electrical power circuit to the motor of the

chainsaw.

• Switch Lockout - A movable stop that prevents the

unintentional operation of the switch until manuallyactuated.

• Trimming (Pruning) - Process of cutting limbs from atree.

• Undercut - An upward cut from underside of a log or limb.

This is done while in normal cutting position and cutting with

top of guidebar.

Storage

1 . Store indoors. The best storage place is one that is cool and

dry away from direct sunlight, excess heat or cold and out of

the reach ofchildren.

2 . Always reduce the tension off the chain again after

finishing work. The chain contracts as it cools down. If

tension is not reduced, it can damage thesaw.

Pinching the saw chain along the top of the guide bar may

push the guide bar rapidly back towards the operator.

Either of these reactions may cause you to lose control of

the saw which could result in serious injury touser.

THE FOLLOWING PRECAUTIONS SHOULD BE

FOLLOWED TO MINIMIZE KICKBACK:

• Grip pole saw firmly. Hold the saw firmly with both hands

when the unit is running. Use a firm grip with thumbs and

fingers encircling the saw handle andpole.

• Do notoverreach.

• Keep proper footing and balance at alltimes.

• Don’t let the nose of the guide bar contact a log, branch,

ground or otherobstruction.

• Do not extend pole saw handle above shoulderheight.

• Use devices such as reduced kickback chain, chain braking

system and special guide bars that reduce the risks associated

withkickback.

• Only use replacement bars and chains specified by the

manufacturer or theequivalent.

• Never let the moving chain contact any object at the tip of the

guidebar.

• Keep the working area free from obstructions such as other

trees, branches, rocks, fences, stumps, etc. Eliminate or avoid

any obstruction that your saw chain could hit while you are

cutting through a particular log orbranch.

• Keep your saw chain sharp and properly tensioned. A loose

or dull chain can increase the chance of kickback. Check

tension at regular intervals with the motor stopped and

batteryremoved.

• Begin and continue cutting only with the chain moving at

full speed. If the chain is moving at a slower speed, there is a

greater chance for kickback tooccur.

• Cut one branch at atime.

• Use extreme caution when re-entering a previous cut. Engage

spiked bumpers into wood and allow chain to reach full speed

before proceeding withcut.

• Do not attempt plunge cuts or borecuts.

• Watch for shifting branches or other forces that could close a

cut and pinch or fall intochain.

Kickback Safety Features

WARNING: The following features are included on

your pole saw to help reduce the hazard of kickback;

however such features will not totally eliminate this

dangerous reaction. As a pole saw user do not rely only

on safety devices. You must follow all safety precautions,

instructions, and maintenance in this manual to help avoid

kickback and other forces which can result in seriousinjury.

• Reduced-Kickback Guide Bar, designed with a small

radius tip which reduces the size of the kickback danger zone

on bar tip. A reduced- kickback guide bar is one which has

been demonstrated to significantly reduce the number and

seriousness of kickbacks when tested in accordance with

safety requirements for electric chainsaws.

Residual Risks

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

ENGLISH

CAUTION: Burn hazard. To reduce the risk of injury,

charge only

DEWALT

rechargeable batteries. Other types of

batteries may burst causing personal injury anddamage.

CAUTION: Children should be supervised to ensure that

they do not play with theappliance.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the exposed charging

contacts inside the charger can be shorted by foreign

material. Foreign materials of a conductive nature such

as, but not limited to, steel wool, aluminum foil or any

buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity.

Unplug charger before attempting toclean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger

and battery pack are specifically designed to worktogether.

• These chargers are not intended for any uses other than

charging

DEWALT

rechargeable batteries. Any other uses

may result in risk of fire, electric shock orelectrocution.

• Do not expose charger to rain orsnow.

• Pull by plug rather than cord when disconnecting

charger. This will reduce risk ofdamage to electric plug

andcord.

• Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire,electric shock, orelectrocution.

• Do not place any object on top of charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source. The

charger is ventilated through slots in the top and the bottom

of thehousing.

• Do not operate charger with damaged cord or plug—

have them replacedimmediately.

• Do not operate charger if it has received a sharp blow,

been dropped, or otherwise damaged in any way. Take it

to an authorised servicecentre.

• Do not disassemble charger; take it to an authorised

service centre when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution

orfire.

• In case of damaged power supply cord, the supply cord must

be replaced immediately by the manufacturer, its service agent

or similar qualified person to prevent anyhazard.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect two chargerstogether.

• The charger is designed to operate on standard

230V household electrical power. Do not attempt to

Chargers

DEWALT

chargers require no adjustment and are designed to be

as easy as possible tooperate.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of yourmains.

Your

DEWALT

charger is double insulated in

accordance with EN60335; therefore no earth wire

isrequired.

If the supply cord is damaged, it must be replaced by a

specially prepared cord available through the

DEWALT

serviceorganisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the oldplug.

• Connect the brown lead to the live terminal in theplug.

• Connect the blue lead to the neutralterminal.

WARNING: No connection is to be made to the

earthterminal.

Follow the fitting instructions supplied with good quality plugs.

Recommended fuse: 3A.

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1mm2; the maximum length

is30m.

When using a cable reel, always unwind the cablecompletely.

Important Safety Instructions for All Battery

Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for compatible battery

chargers (refer to TechnicalData).

• Before using charger, read all instructions and cautionary

markings on charger, battery pack, and product using

batterypack.

WARNING: Shock hazard. Do not allow any liquid to get

inside charger. Electric shock mayresult.

WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA orless.

• Impairment ofhearing.

• Risk of personal injury due to flyingparticles.

• Risk of burns due to accessories becoming hot

duringoperation.

• Risk of personal injury due to prolongeduse.

SAVE THESE INSTRUCTIONS

ENGLISH

Battery Packs

Important Safety Instructions for All Battery

Packs

When ordering replacement battery packs, be sure to include

catalogue number andvoltage.

The battery pack is not fully charged out of the carton. Before

using the battery pack and charger, read the safety instructions

below. Then follow charging proceduresoutlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Inserting or removing the battery from the charger may

ignite the dust orfumes.

• Never force battery pack into charger. Do not modify

battery pack in any way to fit into a non-compatible

charger as battery pack may rupture causing serious

personalinjury.

• Charge the battery packs only in

DEWALT

chargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in locations

where the temperature may fall below 4 ˚C (34 ˚F) (such

as outside sheds or metal buildings in winter), or reach

or exceed 40 ˚C (104 ˚F) (such as outside sheds or metal

buildings insummer).

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

Electronic Protection System

XR Li-Ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deepdischarge.

The tool will automatically turn off if the Electronic Protection

System engages. If this occurs, place the lithium-ion battery

pack on the charger until it is fullycharged.

Wall Mounting

These chargers are designed to be wall mountable or to sit

upright on a table or work surface. If wall mounting, locate the

charger within reach of an electrical outlet, and away from a

corner or other obstructions which may impede air flow. Use

the back of the charger as a template for the location of the

mounting screws on the wall. Mount the charger securely using

drywall screws (purchased separately) at least 25.4mm long

with a screw head diameter of 7–9mm, screwed into wood to

an optimal depth leaving approximately 5.5mm of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using a

cloth or soft non-metallic brush. Do not use water or any

cleaning solutions. Never let any liquid get inside the tool;

never immerse any part of the tool into aliquid.

use it on any other voltage. This does not apply to the

vehicularcharger.

Charging a Battery (Fig. B)

1. Plug the charger into an appropriate outlet before inserting

batterypack.

2. Insert the battery pack 1 into the charger, making sure the

battery pack is fully seated in the charger. The red (charging)

light will blink repeatedly indicating that the charging

process hasstarted.

3. The completion of charge will be indicated by the red

light remaining ON continuously. The battery pack is fully

charged and may be used at this time or left in the charger.

To remove the battery pack from the charger, push the

battery release button 24 on the batterypack.

NOTE: To ensure maximum performance and life of lithium-ion

battery packs, charge the battery pack fully before firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

Charge Indicators

Charging

Fully Charged

Hot/Cold Pack Delay*

* The red light will continue to blink, but a yellow indicator light

will be illuminated during this operation. Once the battery pack

has reached an appropriate temperature, the yellow light will

turn off and the charger will resume the chargingprocedure.

The compatible charger(s) will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing tolight.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and battery

pack to be tested at an authorised servicecentre.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery pack has reached an appropriate

temperature. The charger then automatically switches to the

pack charging mode. This feature ensures maximum battery

packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

The DCB118 charger is equipped with an internal fan designed

to cool the battery pack. The fan will turn on automatically

when the battery pack needs to be cooled. Never operate the

charger if the fan does not operate properly or if ventilation slots

are blocked. Do not permit foreign objects to enter the interior

of thecharger.

ENGLISH

All lithium-ion batteries have the Watt Hour rating marked on

the pack. Furthermore, due to regulation complexities,

DEWALT

does not recommend air shipping lithium-ion battery packs

alone regardless of Watt Hour rating. Shipments of tools with

batteries (combo kits) can be air shipped as excepted if the Watt

Hour rating of the battery pack is no greater than 100Wh.

Regardless of whether a shipment is considered excepted

or fully regulated, it is the shipper's responsibility to consult

the latest regulations for packaging, labeling/marking and

documentationrequirements.

The information provided in this section of the manual is

provided in good faith and believed to be accurate at the time

the document was created. However, no warranty, expressed or

implied, is given. It is the buyer’s responsibility to ensure that its

activities comply with the applicableregulations.

Transporting the FLEXVOLTTM Battery

The

DEWALT

FLEXVOLTTM battery has two modes: Use

andTransport.

Use Mode: When the FLEXVOLTTM battery stands alone or is in

DEWALT

18V product, it will operate as an 18V battery. When

the FLEXVOLTTM battery is in a 54V or a 108V (two 54V batteries)

product, it will operate as a 54Vbattery.

Transport Mode: When the cap is attached to the FLEXVOLTTM

battery, the battery is in Transport mode. Keep the cap

forshipping.

When in Transport mode, strings

of cells are electrically

disconnected within the pack

resulting in 3 batteries with a

lower Watt hour (Wh) rating as compared to 1 battery with a

higher Watt hour rating. This increased quantity of 3 batteries

with the lower Watt hour rating can exempt the pack from

certain shipping regulations that are imposed upon the higher

Watt hour batteries.

For example, the Transport

Wh rating might indicate

3x36 Wh, meaning 3

batteries of 36 Wh each.

The Use Wh rating might

indicate 108Wh (1batteryimplied).

Storage Recommendations

1. The best storage place is one that is cool and dry away

from direct sunlight and excess heat or cold. For optimum

battery performance and life, store battery packs at room

temperature when not inuse.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool, dry place out of the charger for

optimalresults.

NOTE: Battery packs should not be stored completely

depleted of charge. The battery pack will need to be recharged

beforeuse.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the labels

on the charger and the battery pack may show the following

pictographs:

Example of Use and Transport Label Marking

explode in a fire. Toxic fumes and materials are created when

lithium-ion battery packs areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open eye

for 15 minutes or until irritation ceases. If medical attention

is needed, the battery electrolyte is composed of a mixture of

liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek

medicalattention.

WARNING: Burn hazard. Battery liquid may be flammable

if exposed to spark orflame.

WARNING: Never attempt to open the battery pack for

any reason. If battery pack case is cracked or damaged,

do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that

has received a sharp blow, been dropped, run over or

damaged in any way (i.e., pierced with a nail, hit with

a hammer, stepped on). Electric shock or electrocution

may result. Damaged battery packs should be returned to

service centre forrecycling.

WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do not place

the battery pack in aprons, pockets, tool boxes, product kit

boxes, drawers, etc., with loose nails, screws, keys,etc.

CAUTION: When not in use, place tool on its side on

a stable surface where it will not cause a tripping

or falling hazard. Some tools with large battery packs

will stand upright on the battery pack but may be easily

knockedover.

Transportation

WARNING: Fire hazard. Transporting batteries can

possibly cause fire if the battery terminals inadvertently

come in contact with conductive materials. When

transporting batteries, make sure that the battery

terminals are protected and well insulated from

materials that could contact them and cause a short

circuit. NOTE: Lithium-ion batteries should not be put in

checkedbaggage.

DEWALT

batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards which

include UN Recommendations on the Transport of Dangerous

Goods; International Air Transport Association (IATA) Dangerous

Goods Regulations, International Maritime Dangerous Goods

(IMDG) Regulations, and the European Agreement Concerning

The International Carriage of Dangerous Goods by Road (ADR).

Lithium-ion cells and batteries have been tested to section 38.3

of the UN Recommendations on the Transport of Dangerous

Goods Manual of Tests andCriteria.

In most instances, shipping a

DEWALT

battery pack will be

excepted from being classified as a fully regulated Class 9

Hazardous Material. In general, only shipments containing a

lithium-ion battery with an energy rating greater than 100 Watt

Hours (Wh) will require being shipped as fully regulated Class 9.

ENGLISH

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual beforeuse.

Wear eyeprotection.

Wear earprotection.

Do not leave inrain.

Wear headprotection.

Wear protectivegloves.

Cut hazard. Keep fingers away fromslot.

Wear protectivefootwear.

Rotational direction of the sawchain.

Electrocution hazard. Keep at least 10 m away from

overheadlines.

Switch the tool off. Before performing any maintenance

on the tool, remove the battery from thetool.

Directive 2000/14/EC guaranteed soundpower.

Keep bystandersaway.

Package Contents

The package contains:

1 Pole saw

1 Shoulder strap

1 Li-Ion battery pack (C1, D1, L1, M1, P1, S1, T1, X1, Y1 models)

2 Li-Ion battery packs (C2, D2, L2, M2, P2, S2, T2, X2, Y2 models)

3 Li-Ion battery packs (C3, D3, L3, M3, P3, S3, T3, X3, Y3 models)

1 Instruction manual

NOTE: Battery packs, chargers and kitboxes are not included

with N models. Battery packs and chargers are not included with

NT models. Bmodels include Bluetooth® batterypacks.

NOTE: The Bluetooth® word mark and logos are registered

trademarks owned by the Bluetooth®, SIG, Inc. and any use of

such marks by

DEWALT

is under license. Other trademarks and

trade names are those of their respectiveowners.

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Date Code Position (Fig. A)

The date code 14, which also includes the year of manufacture,

is printed into thehousing.

Example:

2019 XX XX

Year of Manufacture

Battery Type

The following SKUs operate on a 18 volt battery pack:

DCMPS567

These battery packs may be used: DCB181, DCB182, DCB183,

DCB183B, DCB184, DCB184B, DCB185, DCB187, DCB189,

DCB546, DCB547, DCB548. Refer to Technical Data for

moreinformation.

Read instruction manual beforeuse.

See Technical Data for chargingtime.

Do not probe with conductiveobjects.

Do not charge damaged batterypacks.

Do not expose towater.

Have defective cords replacedimmediately.

Charge only between 4 ˚C and 40 ˚C.

Only for indooruse.

Discard the battery pack with due care for

theenvironment.

Charge

DEWALT

battery packs only with designated

DEWALT

chargers. Charging battery packs other

than the designated

DEWALT

batteries with a

DEWALT

charger may make them burst or lead to

other dangeroussituations.

Do not incinerate the batterypack.

USE (without transport cap). Example: Wh rating

indicates 108 Wh (1 battery with 108 Wh).

TRANSPORT (with built-in transport cap). Example:

Wh rating indicates 3 x 36 Wh (3batteries of 36Wh).

ENGLISH

Installing and Removing Saw Chain

(Fig. A, C–E)

WARNING: Sharp moving blade. To prevent accidental

operation, insure that battery is disconnected from the

handle before performing the following operations. Failure

to do this could result in serious personal injury.

CAUTION: Sharp moving blade. Always wear protective

gloves when installing or removing the chain. The chain is

sharp and can cut you when it is notrunning.

1. Place the pole saw on a firm surface. Rotate the two

hex head screws12 counterclockwise with the hex

wrench 16provided.

2. Remove sprocket cover11, bar clamp10, and hex

headscrews.

3. To remove the saw chain14, rotate the screw20 in the

front of the housing using the flat screwdriver end of the

wrench. Turning the screw counterclockwise allows the

guide bar13 to recede and reduces the tension on the

chain so that it may beremoved.

4. Lift the worn saw chain out of the groove in the guidebar.

5. Flip guide barover.

6. To replace the saw chain, check to make sure that the

slot in the guide bar is over the location pins21 shown

in Fig.E and that hole below the slot is located over the

adjustmentpin.

7. Place new chain in groove of guide bar and around

sprocket. Make sure saw teeth are facing correct direction by

matching the graphic onhousing or guidebar.

8. Rotate the screw in the front of the housing clockwise to

increase the chaintension.

9. Replace sprocket cover, bar clamp, and hex headscrews.

10. Follow the instructions in the section Adjusting

ChainTension.

Adjusting Chain Tension (Fig. A, D, F, G)

1. With the pole saw still on a firm surface check the saw

chain14 tension. The tension is correct when the saw

chain snaps back after being pulled 3 mm away from the

guide bar13 with light force from the middle finger and

thumb as shown in Fig.F. There should be no “sag” between

Inserting and Removing the Battery Pack

from the Tool (Fig. B)

NOTE: Make sure your battery pack 1 is fullycharged.

To Install the Battery Pack into the Tool Handle

1. Align the battery pack 1 with the rails inside the tool’s

handle (Fig. B).

2. Slide it into the handle until the battery pack is firmly seated

in the tool and ensure that you hear the lock snap intoplace.

To Remove the Battery Pack from the Tool

1. Press the release button 24 and firmly pull the battery pack

out of the toolhandle.

2. Insert battery pack into the charger as described in the

charger section of thismanual.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

WARNING: Use only

DEWALT

battery packs andchargers.

Description (Fig. A)

WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

1 Handle assembly

2 Center extension pole

3 Saw head assembly

4 Trigger switch

5 Lock button

6 Battery

7 Foam gripper

8 Threaded pole

9 Threaded sleeve

10 Bar clamp

11 Sprocket cover

12 Hex head screws

13 Guide bar

14 Saw chain

15 Scabbard

16 Hex wrench

17 Oil cap

18 Branch removal hook

19 Strap mount

Intended Use

This pole saw is ideal for pruning applications and cutting limbs

up to 203 mm indiameter.

DO NOT use under wet conditions or in the presence of

flammable liquids orgases.

This pole saw is a professional powertool.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

• Young children and the infirm. This appliance is not

intended for use by young children or infirm persons

withoutsupervision.

• This product is not intended for use by persons (including

children) suffering from diminished physical, sensory or

mental abilities; lack of experience, knowledge or skills

unless they are supervised by a person responsible for their

safety. Children should never be left alone with thisproduct.

Fuel Gauge Battery Packs (Fig. B)

Some

DEWALT

battery packs include a fuel gauge which

consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

To actuate the fuel gauge, press and hold the fuel gauge

button 27. A combination of the three green LED lights will

illuminate designating the level of charge left. When the level

of charge in the battery is below the usable limit, the fuel gauge

will not illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

ENGLISH

The three assemblies which make up the pole saw are keyed

to insure correct assembly. If an assembly does not smoothly

attach to another do not force fit.

Combining the handle assembly1 to the saw head

assembly3 creates a pole saw that is approximately 1.8m in

length as shown in Fig. I.

To attach the handle assembly to the saw head assembly:

1. Align the groove22 on the outside of the coupling end of

the handle assembly1 with the tongue23 on the inside

of the coupling end of the saw head assembly3. Refer to

Fig.J. Push the two sections completelytogether. Refer to

Fig.K.

2. Slide the threaded sleeve9 on the saw head assembly

down as far as possible and rotate the sleeve clockwise

until it stops and completely covers the threads as shown

in Fig.L.

WARNING: Always check to make sure that the sleeve

is completely threaded on and that the red threads are

no longer visible. Not threading the sleeve completely

on could result in the assembly becoming disconnected

creating a hazardous condition. Periodically check the

connections to insure that no red threads arevisible.

Joining Center Extension to Saw Head

Module and Handle Module (Fig. A, M)

Adding the center extension2 to the handle assembly1 and

saw head assembly3 creates a pole saw that is approximately

2.7 m in length as shown in Fig.M.

Refer to to Joining Saw Head Module to HandleModule for

directions on how to attach the middle assembly to the handle

assembly and saw headassembly.

WARNING: Always check to make sure that the sleeve

is completely threaded on and that the red threads are

no longer visible. Not threading the sleeve completely

on could result in the assemblys becoming disconnected

creating a hazardous condition. Periodically check the

connections to insure that no red threads arevisible.

DISASSEMBLY

WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

Detaching Saw Head Module (Fig. N)

WARNING: Sharp moving blade. To prevent accidental

operation, insure that battery is disconnected from the

handle and that the protective scabbard is in place on the

chain before performing the following operations. Failure

to do this could result in serious personal injury.

When detaching the assemblies, whether it is in the two

assembly or three assembly mode, always detach the saw head

assembly3 first. To do this, rest the handle assembly1 on the

ground and grasp the center of the saw head assembly with

the guide bar and the saw chain on the underside as shown

in Fig.G.

2. To adjust saw chain tension, loosen hex head

screws12.

3. Rotate the screw20 in the front of the housing using the

flat screwdriver end of thewrench.

4. Do not over-tension the saw chain as this will lead to

excessive wear and will reduce the life of the guide bar and

saw chain. Overtensioning also reduces the amount of cuts

you will get per batterycharge.

5. Once saw chain tension is correct, tighten hex head

screws12 to clampbar.

6. When the saw chain is new check the tension frequently

(after disconnecting battery) during the first 2 hours of use

as a new chain stretchesslightly.

NOTE: Saw chain tension should be adjustedregularly.

Saw Chain and Guide Bar Oiling (Fig.H)

Auto Oiling System

This pole saw is equipped with an auto oiling system that keeps

the saw chain and guide bar constantly lubricated. The oil level

indicator25 shows the level of the oil in the chain saw. If the oil

level is less than a quarter full, remove the battery from the pole

saw and refill with the correct type ofoil.

NOTE: Always empty oil tank when finishedcutting.

NOTE: Use a high quality bar and chain oil for proper chain

and bar lubrication. As a temporary substitute, a non-detergent

SAE30 weight motor oil can be used. The use of a vegetable

based bar and chain oil is recommended when pruning trees.

Mineral oil is not recommended because it may harm trees.

Never use waste oil or very thick oil. These may damage your

polesaw.

Filling the Oil Reservoir

• Remove the oil cap17 and fill the reservoir with the

recommended bar and chain oil until the oil level has

reached the top of the oil level indicator25.

• Refit the oilcap.

• Periodically switch the chain saw off and check the oil

level indicator to ensure the bar and chain are being

properlyoiled.

Transporting Pole Saw (Fig. A)

Always remove the battery pack6 from the handle and cover

the saw chain14 with the scabbard15 when transporting the

pole saw.

Joining Saw Head Module to HandleModule

(Fig. I–L)

WARNING: Sharp moving blade. To prevent accidental

operation, insure that battery is disconnected from the

handle and that the protective scabbard is in place on the

chain before performing the following operations. Failure

to do this could result in serious personal injury.

ENGLISH

Proper hand position requires one hand on the main handle29

and one hand on the foam gripper7.

Operating the Pole Saw (Fig. A)

WARNING: Read and understand all instructions. Failure

to follow all instructions listed below may result in electric

shock, fire and/or serious personalinjury.

CAUTION: Always reduce the tension off the chain again

after finishing work. The chain contracts as it cools down.

If it is not slackened off, it can damage the polesaw.

IMPORTANT: Never operate a pole saw that is damaged or

improperly adjusted or that is not completely and securely

assembled. Be sure that the saw chain14 stops moving when

the trigger switch is released. Never adjust the guide bar13

or saw chain when the motor is operating or the battery

isattached.

Pole Saw Trimming/Pruning

WARNINGS:

• Never stand directly under the limb you are cutting.

Always position yourself out of the path of fallingdebris.

• Always wear head, eye, foot and body protection.

Wearing body protection helps reduce the risk of injury when

operating thisunit.

• Never stand on a ladder or other unstable support while

using the pole saw. Always avoid any position which can

cause you to loose your balance and cause severeinjury.

Proper Hand Position (Fig. P)

WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.

WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

OPERATION

Instructions for Use

WARNING: Always observe the safety instructions and

applicableregulations.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

one hand as shown in Fig.N. Use your other hand to loosen the

threaded sleeve and then pull the two halves apart. Repeat this

process if the center extension wasattached.

Attaching and Adjusting the Shoulder Strap

(Fig. O)

This pole saw comes with an adjustable shoulderstrap.

1. Snap the shoulder strap latch28 onto the strap mount19

as shown in Fig.O.

2. Adjust the strap so it fits securely over yourshoulder.

• Keep other persons at least 15 m from the work area.

Distractions can cause you to losecontrol.

• Electrocution Hazard. To prevent shock, do not operate

within 15 m of overhead electrical lines. Always check

surrounding area for hidden electricallines.

• Do not extend pole saw switch handle above

shoulderheight.

On/Off Switch (Fig. Q)

Always be sure of your footing and grip the pole saw firmly with

both hands with the thumb and fingers encircling the handle.

To turn the tool ON pull the lock button5 back with your

thumb and then squeeze the trigger switch4 with your fingers

as shown in Fig. Q. (Once the tool is running you can release the

lock button.) To turn the tool OFF, release the trigger.

Branch Removal Hook (Fig. A)

CAUTION: The branch removal hook is not a belt hook.

Your pole saw includes a branch removal hook

18

for the

intended purpose of helping to remove small to moderately sized

prunedbranches.

Pruning With the Pole Saw (Fig. A, P, R)

WARNING: Let the tool work at its own pace. Do

notoverload.

WARNING: When pruning trees: guard against kickback

which can result in severe injury or death. See Guard

Against Kickback, to avoid the risk of kickback. Do not

overreach. Make sure your footing is firm. Keep feet apart.

Divide your weight evenly on both feet.

1. Use both hands to grip pole saw as shown in Fig.P. Use a

firm grip. Thumbs and fingers must wrap around pole saw

handle and pole. Keep fingers away from sawdust exhaust

chute26 shown in Fig.R.

2. Never operate while in a tree, in any awkward position or on

a ladder or other unstable surface. You may lose control of

pole saw causing severe injury.

3. Follow directions below to trim atee.

a. Make sure pole saw is running at full speed before

making a cut. When starting a cut, place moving saw

chain14 against limb. Hold pole saw firmly in place to

avoid possible bouncing or skating (sideways movement)

of polesaw.

b. Guide pole saw using light pressure. Make first cut

152mm from tree trunk on underside of limb. Use top of

guide bar13 to make this cut. Cut 1/3 through diameter

of limb. Then make the finish cut from the top. If you try

to cut off thick branches from the bottom, the branch

may close in and pinch the saw chain in the cut. If you try

to cut off thick branches from the top, without a shallow

undercut, the branch may splinter. Do not force pole saw.

The motor will overload and can burn out. It will do the

job better and safer at the rate for which it wasintended.

c. Remove pole saw from cut while it is running at full

speed. Stop pole saw by releasing trigger switch4.

ENGLISH

Protecting the Environment

Separate collection. Products and batteries marked

with this symbol must not be disposed of with normal

householdwaste.

Products and batteries contain materials that can

be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails

to produce sufficient power on jobs which were easily done

before. At the end of its technical life, discard it with due care for

our environment:

• Run the battery pack down completely, then remove it from

thetool.

• Li-Ion cells are recyclable. Take them to your dealer or a

local recycling station. The collected battery packs will be

recycled or disposed ofproperly.

Replacement chain and bar are available from your

nearest

DEWALT

servicecenter.

• DCMPS567 requires replacement chain service part

number DT20667-QZ. Replacement 20 cm (8 inch) bar,

service part numberDT20668-QZ.

Optional Accessories

WARNING: Since accessories, other than those offered

DEWALT

, have not been tested with this product, use

of such accessories with this tool could be hazardous.

To reduce the risk of injury, only

DEWALT

recommended

accessories should be used with thisproduct.

Cleaning

WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.

WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Lubrication

Your power tool requires no additionallubrication.

MAINTENANCE

Your power tool has been designed to operate over a long

period of time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care and

regularcleaning.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start-up can causeinjury.

The charger and battery pack are notserviceable.

Make sure saw chain has stopped before setting pole

sawdown.

Saw Chain Sharpness

CAUTION: Sharp chain. Always wear protective gloves

when handling the chain. The chain is sharp and can cut

you when it is notrunning.

IMPORTANT: The chain cutters will dull immediately if they

touch the ground, stones, masonry or a nail whilecutting.

To get the best possible performance from your chain saw, it

is important to keep the teeth of the saw chain sharp. Chain

sharpening services are available from your nearest

DEWALT

servicecenter.

NOTE: Each time the saw chain is sharpened, it loses some

of the reduced kickback qualities and extra caution should be

used. It is recommended that a saw chain be sharpened no

more than fourtimes.

Consult your dealer for further information on the

appropriateaccessories.

Страница загружается...

DeWalt DCMPS567 Инструкция по эксплуатации

Похожие модели бренда

Модели других брендов