Yamaha psr-5700 Инструкция по применению

Advanced Features

Programmieranleitung

Fonctions avancées

Características avanzadas

OWNER’S MANUAL

Advanced Features

BEDIENUNGSANLEITUNG

Programmieranleitung

MODE D’EMPLOI

Fonctions avancées

MANUAL DE INSTRUCCIONES

Características avanzadas

2

The Sequencer .................................................................... 3

■ Recording ....................................................................... 3

■ Deleting Tracks ............................................................... 5

■ Playback ......................................................................... 6

■ Sequence Editing ........................................................... 7

E1 CONDITION/REC TYPE ............................................. 7

E2 VOLUME................................................................... 8

E3 TRACK COPY/MIX ..................................................... 9

E4 QUANTIZE .............................................................. 10

E5 DELETE ALL TRACKS ............................................. 11

E6 INSERT ALL TRACKS .............................................. 12

E7 ERASE ................................................................... 12

E8 REMOVE EVENT ..................................................... 13

E9 NOTE SHIFT ........................................................... 14

E10 SONG CLEAR ....................................................... 14

The Custom Accompaniment Programmer............... 15

■ Basic Programming Procedure ..................................... 15

■ Using a Custom Accompaniment ................................. 18

■ Custom Accompaniment Editing .................................. 19

1 CUSTOM ACCOMP. (Measure/Beat)............................ 19

2 VOLUME ................................................................... 19

3 FADER SELECT ........................................................ 20

4 NAME ....................................................................... 20

5 SAVE TO ACCOMP.................................................... 20

6 QUANTIZE ................................................................ 21

7 COPY ....................................................................... 22

8 REMOVE EVENT ....................................................... 23

9 CHANGE PATTERN ................................................... 23

• CREATING INTRO, FILL-IN, & ENDING PATTERNS ...... 24

• EXITING FROM THE CUSTOM ACCOMPANIMENT

MODE ....................................................................... 25

Other Functions ................................................................ 26

■ General Function Selection & Editing Procedure ......... 26

[F1] Custom Voice Edit ................................................... 27

■ Standard Voice Edit Functions

(Voices 00 through 89) .... 27

1 NAME ....................................................................... 27

2 COMMON ................................................................. 28

3 MODULATION ........................................................... 28

4 EG RATE .................................................................. 29

5 TONE ....................................................................... 30

■ Dual Voice Edit Functions (Voices 90 through 97) ........... 30

1 DUAL NAME.............................................................. 30

2 DUAL VOICE ............................................................. 31

3 DUAL OCTAVE .......................................................... 31

4 DUAL VOLUME ......................................................... 31

5 DUAL PAN ................................................................ 32

6 DUAL DETUNE .......................................................... 32

■ Drum Voice Edit Functions (Voices 98 and 99) ............... 33

1 PERC. NAME ............................................................ 33

2 PERC. PITCH ............................................................ 33

3 PERC. PAN ............................................................... 34

4 PERC. TONE ............................................................. 34

[F2] Reverb, Effect............................................................ 35

1 REVERB TYPE .......................................................... 35

2 REVERB DEPTH ....................................................... 35

3 EFFECT TYPE........................................................... 36

4 EFFECT DEPTH ........................................................ 36

[F3] Controller & Key Velocity....................................... 37

1 KEY VELOCITY ......................................................... 37

2 FOOT SWITCH SELECT ............................................ 37

3 EXP. PEDAL SELECT ................................................ 38

4 SUSTAIN PART SELECT ............................................ 38

5 PITCH BEND SELECT ............................................... 39

6 WHEEL SELECT ....................................................... 39

[F4] Split Point, Interactive Accompaniment, &

Super Style Play Mode ........................................... 40

1 SPLIT POINT ............................................................. 40

2 INTERACTIVE ACCOMP. ........................................... 40

3 SUPER STYLE PLAY MODE ....................................... 41

[F5] Disk .............................................................................. 42

■ The [TO DISK] Button ................................................... 42

■ The [FROM DISK] Button ............................................. 44

■ The [F5] DISK Functions .............................................. 45

1 FROM DISK .............................................................. 45

2 TO DISK ................................................................... 46

3 RENAME FILE ........................................................... 46

4 DELETE FILE ............................................................ 47

5 FORMAT DISK .......................................................... 47

6 DISK FREE AREA ...................................................... 47

• Disk Error Messages .................................................. 48

[F6] Utility & MIDI .............................................................. 49

1 MEMORY BACKUP .................................................... 49

2 RECALL INITIAL DATA ............................................... 50

■ The [DISK ORCHESTRA/GENERAL MIDI] Button ...... 50

3 MIDI CHANNEL SETTING ........................................... 54

4 MULTI PART SETTING .............................................. 56

5 MIDI SWITCH ............................................................ 56

6 MIDI SYSTEM ........................................................... 57

7 DATA TRANSMIT ...................................................... 58

Index..................................................................................... 59

MIDI Function Tree ......................................................... 242

MIDI Messages .............................................................. 246

DISK ORCHESTRA (DOC) Mode Voice List ................. 253

GENERAL MIDI (GM) Mode Voice List .......................... 254

PSR-5700 Percussion Map ............................................ 255

GM/DOC Mode Percussion Map .................................... 256

MIDI Implementation Chart ............................................ 257

Specificationes ............................................................... 258

The PSR-5700 Advanced Features manual contains operating instructions for the instrument’s

more complex and advanced features. If you are yet familiar with PSR-5700’s basic features and the

way it works in general, we recommend that you go through the PSR-5700 Getting Started manual

prior to attempting to use the features described in this manual.

Contents

3

CSet Up All Record Parameters

Select the accompaniment style you want to record with, voices, orches-

tration, harmony, and other parameters before actually beginning recording.

A list of the parameters that can be recorded by the PSR-5700 sequencer is

given below.

You may also need to select a specific record mode and other conditions

accessible via the sequencer’s CONDITION/RECORD TYPE functions,

described on page 7.

ZEngage the Sequencer

DETAIL

XSelect a Song Number

Press the [SEQUENCER] button to engage the sequencer. “SEQ” will

appear on the TEMPO display if the currently selected song contains no

data, or the measure number will appear if the song does contain data. The

number-1 indicator to the right of the [SONG SELECT] button will also

light.

If the sequencer contains previously recorded data, the green PLAY indi-

cators of tracks containing data will light when the sequencer is engaged.

Any of these tracks can be muted prior to engaging the record-ready mode

(below) by pressing the corresponding track button so that the green PLAY

indicator flashes.

The sequencer can also be engaged by pressing one of the track buttons, or by

pressing the [SONG SELECT] button.

The PSR-5700 sequencer can record up to 6 separate songs. Use the

[SONG SELECT] button to select the song number you want to record. The

selected song number is shown by the indicators, 1 through 6, to the right of

the [SONG SELECT] button.

CUSTOM ACCOMPANIMENT PRO

G

SEQUENCER

SONG

SELECT

1

Recording

As you become more familiar with the PSR-5700 sequencer you’ll probably develop a recording procedure

that best suits your particular musical requirements. Here, to get you started, is the most simple, straightfor-

ward way to approach sequencer recording.

The PSR-5700 features an 8-track sequencer that allows you to record and play back original musi-

cal creations — along with auto accompaniment if required. You can record the accompaniment and

orchestra parts separately or at the same time. If, for example, you record the accompaniment first

and then record your own performance while listening to playback of the accompaniment, you’re free

to use the entire keyboard for your performance rather than being limited to only the upper keyboard

area. You can also play back each part independently or in any combination. For even further versatil-

ity, the PSR-5700 sequencer allows different songs to be saved to or re-loaded from floppy disk.

The Sequencer

CUSTOM ACCOMPANIMENT PROGRAMMER

SEQUENCER

SONG

SELECT

123456

4

The Sequencer

Recordable Parameters

Tracks 1 — 7

• Note on/off

• Pitch bend

• Modulation

• Sustain on/off

• Orchestra 1 & 2 volume

• Voice change (including custom voice on/off)

• Tempo (if ACCOMP. track contains no data)

• Glide on/off

• Percussion pad on/off*

• Tempo pad tempo value*

• Multi pad on/off (phrase only)*

* The pad mode selected when the sequence

is played back will be used.

Accompaniment Track

• Chord & root (note on/off in Manual Bass

mode)

• Style change (styles with the same time

signature only)

• Rhythm volume

• Bass volume

• Chord 1 volume

• Chord 2 volume

• Tempo

• Reverb on/off & depth

• Reverb type

• Effect on/off & depth

• Effect type

• Effect control

• Harmony on/off and type

• Interactive Accompaniment on/off

• Interactive Accompaniment variation

• Interactive Accompaniment mode & sensitivity

• Auto Bass Chord mode

• Percussion Pad on/off

• Pad function (Multi/Tempo/Perc)

• Repeat/Synchro/Break on/off

• Manual bass on/off, voice

• Intro, fill in & ending

• Chord pad chord sequence

• Tempo pad tempo value

IMPORTANT

When the sequencer mode is engaged all previous panel settings are ignored.

If the record and playback pad modes are different, pad on/off events will not be

reproduced.

If parameter changes are memorized using the Voice Registration, Panel Regis-

tration, or Super Styleplay features during recording, only those parameters that

can be recorded on the current track will be memorized.

The time signature cannot be changed once a song has been recorded.

AUTO BASS CHORD accompaniment can only be recorded on the

ACCOMP. track. The ORCH.1 and ORCH.2 voices can be recorded on any

of the remaining 7 tracks, but only one of these tracks can be recorded at a

time if the normal ORCH.1 orchestration is selected. If the ORCH.2+1 or

ORCH.2v1 orchestration is selected, two record tracks must be selected

— the ORCH.1 voice will be recorded on the lower-numbered track while

the ORCH.2 voice will be recorded on the higher-numbered track. This

means that a maximum of three record tracks can be specified when the

ORCH.2+1 or ORCH.2v1 orchestration is selected: ACCOMP. and any

two numbered tracks.

To select the record track(s) and engage the record-ready mode, hold the

[RECORD] button and press the appropriate track button(s). The red REC

indicator for the tracks will flash. Also note that the AUTO BASS CHORD

indicator will light automatically when the ACCOMP. track is selected.

DETAIL

HINT

The upper markings on the track buttons apply when the SEQUENCER mode is

engaged (1 through 7, and ACCOMP.). The lower markings when the CUSTOM

ACCOMPANIMENT PROGRAMMER described on page 15 is operating.

If you are adding new material to tracks that have already been recorded, the

[

r

] and [

f

] buttons can be used at this point to move to any measure number

from which you want to begin recording. The [

r

] and [

f

] buttons will not

function once recording has been started.

prf

RECORD DELETE EDIT

CHORD 1 CHORD 2 CHORD 3 CHORD 4 CHORD 5 CHORD 6 BASS RHYTHM

1 2 3 4 5 6 7 ACCOMP.

PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC

VSelect the Record Track(s)

5

The Sequencer

Recording will start as soon as the [START/RE-START] button is pressed or,

if you also press the [SYNCHRO START] button, as soon as any key on the key-

board is pressed.

If the ACCOMP. track is selected and you start recording by pressing the

[START/RE-START] button, only the rhythm will play until the first chord

(FINGERED or SINGLE FINGER) is played on the left-hand section of the key-

board.

If you start recording in the SYNCHRO START mode by playing on the right-

hand section of the keyboard, a metronome will sound in place of the rhythm and

AUTO BASS CHORD accompaniment until a key is played on the left-hand

section of the keyboard.

Before starting recording you can also choose an introduction by pressing any of the

[INTRO.] buttons.

The restart function can not be used while the sequencer mode is engaged.

Previously recorded fill-ins may not always be erased if that section is re-recorded or

deleted.

Play the accompaniment and/or orchestra parts. The current measure number is

shown on the TEMPO display as you record.

Press the [STOP] button to stop recording immediately, or the [ENDING/rit.]

button to finish off the recording with an appropriate ending. The first measure of

the sequence is automatically selected when recording is stopped.

To record a new track, simply select a new voice and other parameters as re-

quired, select a new track as described in step 4, then record. All previously re-

corded tracks will automatically be set to the PLAY mode so you can record the

new material while listening to the material you’ve already recorded. Repeat this

procedure until your sequence is complete.

Up to approximately 7,000 notes can be recorded for all six sequencer songs. The

exact number of notes that can be recorded, however, will depend on the type of data

you record.

SYNCHRO

START

START/

RE-START

STOP

ENDING/

rit.

FILL IN

n

FILL IN

j

INTRO.3INTRO.2INTRO.1

BStart Recording

HINT

DETAIL

NPlay

MStop Recording

ENDING/

rit.

FILL IN

n

FILL IN

j

INTRO.3INTRO.2INTRO.1

SYNCHRO

START

START/

RE-START

STOP

<Record a New Track

DETAIL

Deleting Tracks

If you make a mistake while recording or simply want to delete a track from

your sequence, press the track button corresponding to the track you want to

delete while holding the [DELETE] button.

Tracks cannot be deleted during recording or playback.

prf

RE

CO

RD DELETE EDIT

CHORD 1 CHORD 2 CHORD 3 CHORD 4 CHORD 5 CHORD 6 BASS RHYTHM

1 2 3 4 5 6 7 ACCOMP.

PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC

DETAIL

6

The Sequencer

ZStart Playback

Playback

SYNCHRO

START

START/

RE-START

STOP

CHORD 1 CHORD 2 CHORD 3 CHORD 4 CHORD 5 CHORD 6 BA

S

1234567

PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY

prf

RECORD DELETE EDIT

Since tracks are automatically set to the PLAY mode once they have been

recorded, and tracks containing data are automatically set to the PLAY mode

when the sequencer is initially engaged by pressing the [SEQUENCER] button,

all you have to do to play back a sequence is to press the [START/RE-START]

button. If you first press the [SYNCHRO START] button, sequencer playback

can be started by playing any key on the keyboard.

Any of the PLAY tracks can be muted before or during playback by pressing

the corresponding track button. The PLAY indicator will flash when a track is

muted. Normal playback can be restored by pressing the track buttons of muted

tracks a second time (the PLAY indicator will light continuously).

Before starting playback you can use the [

r

] and [

f

] buttons to move to any

measure number from which you want to begin playback. The [

p

] button goes

directly to measure number 1.

If the Super Styleplay section change parameter (page 41) is turned ON during

ACCOMP. track playback, the Super Styleplay section will change in accordance

with accompaniment variation transitions and the result may be different from the

recorded data.

You can play along with the sequence using the entire PSR-5700 keyboard,

selecting different voices and changing the tempo as required (subsequently

recorded tempo changes will still take effect).

Parameters That Can Be Changed During Playback

• Style select (styles with different time signatures cannot be selected)

• Volume (rhythm, bass, chord 1 & chord 2)

• Tempo

• Reverb & effect on/off

• Pad repeat and break on/off

• Interactive Accompaniment on/off & accompaniment variation

(VERSE 1, VERSE 2, CHORUS 1, CHORUS 2, SOLO)

• Pad

• Some FUNCTION parameters (pages 26 through 58)

If changes to any of the above parameters are recorded in the sequence, the re-

corded changes will still take effect even if you manually change the parameters

while playing.

Playback will stop automatically when the end of the sequence is reached. At

this point the parameters recorded on the ACCOMP. track will revert to their

initial values. You can also stop playback at any time by pressing the [STOP]

button.

Press the [EXIT] key to exit the sequencer mode and return to the normal

play mode. The sequencer mode can also be exited by pressing the [SE-

QUENCER] button.

HINT

DETAIL

CStop Playback

SYNCHRO

START

START/

RE-START

STOP

XPlay along If You Like

FUNCTION

EXIT

VPress [EXIT] When Done

7

Sequence Editing

prf

RECORD DELETE EDIT

DETAIL

+– +–

HARMONY

TYPE

OCTAVE

CHANGE

TRANSPOSE/

TUNE

s

t

<>

A. B. C. MODE

`CONDITION/REC TYPE ‡

Metro=On Harmony=Key

The PSR-5700 sequencer edit mode offers a range of functions that let you modify the re-

corded data and the way in which it is recorded in a number of ways.

Press the [EDIT] button while the sequencer is engaged to enter the sequencer edit mode.

When you’re finished editing press the [EDIT] button again or press the [EXIT] button to return

to the sequencer.

The various functions in the sequencer edit mode are accessed by using the [s] and [t] but-

tons (these are the same as the [ABC MODE] and [HARMONY TYPE] buttons, respectively),

while the various display screens provided by each function are accessed by using the [<] and

[>] buttons (the [TRANSPOSE/TUNE] and [OCTAVE CHANGE] buttons, respectively).

The sequencer record and playback modes can not be engaged while in the edit mode.

The edit functions may not work if a large amount of sequence data has been recorded.

The Sequencer

DETAIL

E1 CONDITION/REC TYPE

Edit function 1 (“E1”) actually includes two separate functions: CONDITION and RECORD TYPE.

+– +–

`CONDITION/REC TYPE ‡

Metro=On Harmony=Key

● Condition

Purpose:

This display page allows the recording metronome sound

to be turned on or off, and determines whether harmony will

be applied to the keyboard or a track part.

Procedure:

Use the left [-] and [+] buttons to turn the metronome on

or off, and the right [-] and [+] buttons to select the harmony

part — “Key” or “Tr1” through “Tr7”.

Notes:

The metronome sound only appears during recording

when no rhythm is playing.

When the “Key” harmony setting is selected (this is the

default setting when the sequencer mode is engaged), har-

mony will be applied to notes played on the keyboard. If the

“Tr1” harmony setting is selected, harmony will be applied

to the track-1 part. If “Tr2” is selected harmony is applied to

track 2, and so on.

If Harmony is not turned on during recording, it will auto-

matically be turned off each time playback is stopped if it is

turned on before or during playback.

Harmony can only be applied to tracks that contain data.

8

The Sequencer

+–

† `REC TYPE

Mode=Replace

+– +–

† `REC TYPE ‡

Mode=Punch Play St= 1

+– +–

† `Punch IN/OUT MEAS.

In= 1 Out= 1

E2 VOLUME

+– +–

“VOL. 1~2'3~4'5~6'7~

99/81/99/81/99/81/99

_

● Recording Type

Purpose:

Selects the Replace, Overdub, or Punch record mode.

Procedure:

Press the [>] button to access the REC TYPE display. Use

the left [-] and [+] buttons to select the Replace, Overdub, or

Punch record mode:

• Replace

If replace recording is selected, any previous data on the

track being recorded will be erased and replaced by the

new material.

• Overdub

If overdub recording is selected, previous material on

that track will be retained and the new material will be

added to it.

• Punch

Punch-in recording allows a specified measure or range

of measures to be re-recorded (replaced) without affecting

previously recorded material before and after the punch-in

range.

When the Punch mode is selected you must also specify

the measure from which playback is to begin prior to the

“punch-in” point at which recording will actually begin

(Play St), the punch-in measure from which recording is

to begin (In), and the punch-out measure at which record-

ing is to end (Out). Use the [<] and [>] buttons to switch

between these two display screens, and the associated [-]

and [+] buttons to specify the required measure numbers.

Notes:

It’s generally convenient to set the “Play St” measure in

the Punch mode to just a few measures before the punch-in

point. This allows you to get the feel of the music and pre-

pare to start playing at the punch-in point. You can even play

along with the material prior to the actual punch-in point so

you’ll flow naturally into the punch-in recording range.

A footswitch (the supplied FC5 footswitch can be used)

plugged into the rear-panel FOOT SW jack can also be used

to punch-in and punch-out when the footswitch “Punch In”

function is selected via the “FOOT SWITCH SELECT”

function described on page 37. With the sequencer running

in the Punch Record mode, press the footswitch at the point

you want to begin recording (i.e. to “punch in”), and again to

stop recording (punch out).

Please note that the punch-in record function can only be

used on tracks that already contain recorded material.

7, from left to right), then use either the left or right [-] and

[+] buttons to set the volume to a value between “00” (mini-

mum volume — no sound) and “99” (maximum volume).

Vertical bar-graphs to the right of each track number on the

top line of the display provide a graphic representation of the

track volume levels.

Notes:

Only tracks that contain data are available for volume

control.

Any recorded volume changes will override these settings.

Purpose:

This page lets you independently set the playback volume

of each of the sequencer’s seven orchestra tracks.

Procedure:

Use the [<] and [>] buttons to position the cursor at the

volume parameter of the track you want to adjust (1 through

9

E3 TRACK COPY/MIX

+– +–

£TRACK COPY/MIX ‡

Source1=Tr1 Source2=Tr2

+– +–

† £COPY/MIX Tr1+Tr2

Dest.=Tr1 Execute

Procedure:

Use the [<] and [>] buttons to switch between the two

display screens, and the left or right [-] and [+] buttons to set

the first source track (Source1), the second source track

(Source2), and the destination track (Dest.). If

“CopyToDest.” is selected for the Source2 parameter, only

the Source1 track is copied to the destination track.

Once the source and destination tracks have been selected,

press the [+] button below “Execute” on the right side of the

display to actually execute the mixdown operation. “Se-

quencer Executing!” will appear on the lower line of the

display while the operation is in progress, and “Completed!”

will appear briefly when the operation has finished.

Immediately after execution “Undo” will appear above the

right [-] button, and that button can be used to undo the

mixdown if it was executed by mistake. The undo function is

only available until the next operation is performed.

Notes:

The mix function is most useful when you want to record

more than 7 individual parts on the seven orchestra-part

tracks. Successfully recorded parts can be combined using

this function, thus opening up more tracks for further record-

ing. The data in the source tracks is not erased during a mix

operation.

If the tracks that are mixed use different voices, the voice

of the lower-numbered track will be used. Subsequent re-

corded voice changes will operate normally.

Please note that only tracks containing data can be speci-

fied as the source tracks.

Any data in the destination track will be overwritten by

data copied from the source 1 and 2 tracks.

Purpose:

Copies the data from one recorded track to another, or

mixes the data from two recorded tracks (except the

ACCOMP. track).

The Sequencer

Data

Copy to Destination track

● Copy

Source track 1

● Mix

Source track 1

Source track 2

Destination track (mix result)

10











3

 

3







3

The Sequencer

E4 QUANTIZE

+– +–

¢QUANTIZE 1/32 ‡

Track=Tr1 Execute

+– +–

† ¢QUANTIZE Tr1

Size=1/32 Execute

eeee eee

e

eeeeeeee

One measure of 8th notes before quantization

After quantization

Immediately after execution “Undo” will appear above the

right [-] button, and that button can be used to undo the

quantize operation if it was executed by mistake. The undo

function is only available until the next operation is per-

formed.

The Quantize Sizes are:

1/4 = 1/4 note

1/6 = 1/4 note triplet

1/8 = 1/8 note

1/12 = 1/8 note triplet

1/16 = 1/16 note

1/24 = 1/16 note triplet

1/32 = 1/32 note

1/96 = maximum resolution

(default)

Notes:

Quantization is generally used to tighten up sloppy timing.

Use it judiciously, however, because timing that is too per-

fect can sound cold and mechanical — unless, of course,

you’re specifically aiming for a cold, mechanical feel. Al-

ways use a quantize value that is at least as “short” as the

shortest notes in the track to be quantized. If you quantize a

track containing 16th notes to 1/8 (8th notes), for example,

some of the 16th notes will be aligned with 8th note beats,

thus ruining the track.

Purpose:

Aligns notes in the specified track to the nearest specified

beat.

Procedure:

Use the [<] and [>] buttons to switch between the two

display screens, and the left [-] and [+] buttons to set the

track number (Track) and the quantize size (Size).

Once the track number and quantize size have been se-

lected, press the [+] button below “Execute” on the right side

of the display to actually execute the quantize operation.

“Sequencer Executing!” will appear on the lower line of the

display while the operation is in progress, and “Completed!”

will appear briefly when the operation has finished.

11

+– +–

DELETE ALL TRACKS ‡

TopMeas= 4 LastMeas= 6

+

† DELETE from 4 to 6

Execute

E5 DELETE ALL TRACKS

123456789

123 789

123456

Measure 4 through 6 deleted.

Delete Measures 4 through 6.

Subsequent measures moved back.

Purpose:

Deletes the specified measure or range of measures from

all tracks (including the accompaniment track).

Procedure:

Use the [<] and [>] buttons to switch between the two

display screens, and the left or right [-] and [+] buttons in the

first display screen to specify the number of the first measure

in the range to be deleted (TopMeas) and the number of the

last measure in the range to be deleted (LastMeas).

Once the top and last measure numbers have been se-

lected, press the [+] button below “Execute” on the right side

of the second display screen to actually execute the delete

operation. “Sequencer Executing!” will appear on the lower

line of the display while the operation is in progress, and

“Completed!” will appear briefly when the operation has

finished.

Notes:

It’s important to remember that a delete operation affects

all tracks simultaneously, and that measures following the

deleted range are moved back to take the place of the deleted

measures. This differentiates the delete job from the erase

job (described later), which replaces data in the specified

range with rests.

Be careful when deleting measures that contain effect on/

off events — e.g. pitch bend, modulation, sustain, harmony,

etc. If, for example, you delete a measure that contains a

pitch bend off event, the pitch bend applied in a previous

measure will remain in effect until the next pitch bend event

is encountered.

The delete operation has no “undo” function, so be abso-

lutely sure you want to delete the selected material before

actually executing the delete operation.

The Sequencer

12

+– +–

†ƒERASE Tr1 from 4

LastMeas= 6 Execute

The Sequencer

E7 ERASE

+– +–

ƒERASE ‡

Track=Tr1 TopMeas= 4

E6 INSERT ALL TRACKS

+– +–

⁄INSERT ALL TRACKS ‡

TopMeas= 6 Size= 3

+

†⁄INSERT from 6size 3

Execute

123456

12345 6

123456789

Insert measure, size 3, at measure 6.

Measure 6 moved up; 3 blank measures inserted.

Result with new measure numbers.

Procedure:

Use the [<] and [>] buttons to switch between the two

display screens, and the left or right [-] and [+] buttons to set

the track number (Track), the number of the first measure in

the range to be erased (TopMeas), and the number of the last

measure in the range to be erased (LastMeas).

Once the track and measure numbers have been selected,

press the [+] button below “Execute” on the right side of the

display to actually execute the erase operation. “Sequencer

Executing!” will appear on the lower line of the display

while the operation is in progress, and “Completed!” will

appear briefly when the operation has finished.

Immediately after execution “Undo” will appear above the

right [-] button, and that button can be used to undo the erase

operation if it was executed by mistake. The undo function is

only available until the next operation is performed.

Notes:

An erase operation leaves the specified measures intact but

blank.

Purpose:

Erases all note and event (pitch bend, volume changes,

etc.) data from the specified measure or range of measures in

the specified track (accompaniment track not available),

leaving blank measures.

Procedure:

Use the [<] and [>] buttons to switch between the two

display screens, and the left or right [-] and [+] buttons in the

first display screen to specify the number of the measure at

which the blank measures are to be inserted (TopMeas) and

the number of blank measures to be inserted (Size).

Once the top measure number and size have been selected,

press the [+] button below “Execute” on the right side of the

second display screen to actually execute the insert opera-

tion. “Sequencer Executing!” will appear on the lower line of

the display while the operation is in progress, and “Com-

pleted!” will appear briefly when the operation has finished.

Notes:

Insert affects all tracks simultaneously. The specified

number of blank measures is inserted before the existing data

beginning at the specified insert measure number.

The insert operation has no “undo” function.

Purpose:

Inserts a specified number of blank measures in all tracks

(including the accompaniment track) at the specified meas-

ure number.

123456789

TRACK 1

123456789

TRACK 1

Erase measures 4 through 6.

Measures 4 — 6 “blank, ”

containing only rests.

13

+– +–

†¥REMOV Tr1 PB ‡

TopMeas= 3 LastMeas= 4

+–

†¥REMOV Tr1 PB 3> 4

Execute

E8 REMOVE EVENT

+– +–

¥REMOVE EVENT ‡

Track=Tr1 Event=PB

Purpose:

Removes all occurrences of the specified event type (pitch

bend, modulation wheel, volume, or sustain operations) from

the specified measure or range of measures in the specified

track (accompaniment track not available).

Procedure:

Use the [<] and [>] buttons to switch between the three

display screens, and the left or right [-] and [+] buttons to set

the track number (Track), the type of event to be removed

(Event), the number of the first measure in the range from

which the events are to be removed (TopMeas), and the

number of the last measure in the range from which the

events are to be removed (LastMeas).

Once the track, event, and measure numbers have been

specified, press the [+] button below “Execute” on the right

side of the display to actually execute the remove event op-

eration. “Sequencer Executing!” will appear on the lower

line of the display while the operation is in progress, and

“Completed!” will appear briefly when the operation has

finished.

Immediately after execution “Undo” will appear above the

right [-] button, and that button can be used to undo the re-

move event operation if it was executed by mistake. The

undo function is only available until the next operation is

performed.

The Event Abbreviations are:

PB = Pitch Bend

MOD = Modulation Wheel

VOL = Volume

SUS = Sustain

VC = Voice Change

Notes:

This function is handy if, for example, you’ve played

some wild pitch bends that don’t sound right. You can re-

move only the offending pitch bends without erasing the

entire track.

Be careful when removing effect on/off events. If, for

example, you remove a pitch bend off event in a specified

measure, the pitch bend applied in a previous measure will

remain in effect until the next pitch bend event is encoun-

tered. Similarly, if you remove all program change events

from the beginning of a track, the voice that was initially

selected when the track was recorded will be used.

The Sequencer

14

+

`…SONG 1 CLEAR

FREE:31k Execute

+– +–

»NOTE SHIFT ‡

Track=Tr1 Shift=+12

+– +–

†»NOTE Tr1 +12 ‡

TopMeas= 1 LastMeas= 16

+–

†»NOTE Tr1 1> 16 +12

Execute

E9 NOTE SHIFT

The Sequencer

E10 SONG CLEAR

Once the track, shift, and measure numbers have been

specified, press the [+] button below “Execute” on the right

side of the display to actually execute the note shift opera-

tion. “Sequencer Executing!” will appear on the lower line of

the display while the operation is in progress, and “Com-

pleted!” will appear briefly when the operation has finished.

Immediately after execution “Undo” will appear above the

right [-] button, and that button can be used to undo the note

shift operation if it was executed by mistake. The undo func-

tion is only available until the next operation is performed.

Notes:

The range of “Shift” values is from -24 to +24. A setting

of “0” produces no note shift. Each increment represents a

semitone, so a setting of +4, for example, would shift the

pitch of notes in the specified range up by an interval of a

third. A setting of -12 would shift the notes down by one

octave.

The ability to selectively shift the pitch of specified meas-

ures and tracks makes it simple to create “modulations” (key

changes) without having to reprogram entire passages, and to

create simple harmonies.

Purpose:

Shifts the pitch of notes in the specified measures of the

specified track (accompaniment track not available) up or

down by a maximum of two octaves, in semitone increments.

Procedure:

Use the [<] and [>] buttons to switch between the three

display screens, and the left or right [-] and [+] buttons to set

the track number (Track), the amount of note shift (Shift —

see “Notes” below), the number of the first measure in the

range in which the notes are to be shifted (TopMeas), and the

number of the last measure in the range in which the notes

are to be shifted (LastMeas).

Notes:

Remember that this function deletes all data in the se-

quencer in one operation. If you think you might want to

keep the data for later use or editing, be sure to save it to

floppy disk (page 42, 46) before executing the song clear

operation. Be careful with SONG CLEAR — it has no

“undo” function!

The remaining amount of sequencer memory is shown on

the bottom line of the display in kilobytes.

Purpose:

Deletes the entire song — i.e. deletes all data from all

sequencer tracks.

Procedure:

Press the [+] button below “Execute” on the display to

execute the song clear operation. “Completed!” will appear

briefly when the operation has finished.

15

The Custom Accompaniment Programmer

The PSR-5700 CUSTOM ACCOMPANIMENT feature allows you to create and store up to six original accompa-

niments — including rhythm, bass, and chords — in addition to 36 internal preset accompaniment styles. You can

even create intro, fill-in, and ending patterns that can be saved with your accompaniments. More custom accom-

paniments can be created and saved to floppy disk (page 42, 46). Your original accompaniments can be selected

and played at any time, just like the presets.

Z

Select a Suitable Accompani-

ment Style

X

Engage the Custom Accom-

paniment Programmer

STYLE SELECT

012345

NUMBER

012345

BANK

CUSTOM ACCOMPANIMENT PROGRAMMER

SEQUENCER

SONG

SELECT

12345

Begin by selecting one of the preset accompaniment styles that is close to

the type of accompaniment you want to create. For example, select a

WALTZ accompaniment style if you want to program a rhythm pattern in

3/4 time.

Press the [CUSTOM ACCOMPANIMENT PROGRAMMER] button.

The selected accompaniment style will begin playing, with accompaniment

based on a C major chord. Also, the rhythm track will be set to the record

mode (red REC indicator lit) and the 98 DRUM KIT voice will be selected.

All other tracks containing data will be set to the PLAY mode (green PLAY

indicator lit). PLAY tracks can be muted by pressing the corresponding

track button (the green PLAY indicator will flash when the track is muted).

Use the [VERSE1], [VERSE2], [CHORUS1], [CHORUS2], and [SOLO]

buttons to select the accompaniment variation you want to program (varia-

tions cannot be selected when a custom style is selected).

Intro, fill-in, and ending patterns will be based on the selected variation.

If you delete all existing data to program an accompaniment from scratch,

and change the time signature (beat), the intro, fill-in, and ending patterns

cannot be used.

Since the RHYTHM track is initially set to the REC mode and the 98

DRUM KIT voice is selected, you can start programming the RHYTHM

track immediately.

You can add new notes to the rhythm by playing the keys corresponding

to the PSR-5700 drums and percussion instruments. The drums and percus-

sion instruments produced are indicated by the symbols immediately above

the keys (see the “KEYBOARD PERCUSSION KEYS” chart on page 14 of

the “Getting Started” manual). Please note that pitch bend can not be ap-

plied to the rhythm instruments.

Basic Programming Procedure

Although many of the steps outlined below do not have to be carried out in the order given, the basic pro-

gramming procedure presented below will serve as useful guide to get you started.

C

Select an Accompaniment

Variation

CHORUS

2

SOLOCHORUS

1

VERSE

2

VERSE

1

VProgram the Rhythm Part

16

prf

RECORD DELETE EDIT

CHORD 1 CHORD 2 CHORD 3 CHORD 4 CHORD 5 CHORD 6 BASS RHYTHM

1 2 3 4 5 6 7 ACCOMP.

PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC

The Custom Accompaniment Programmer

If you want to create a totally new rhythm track, press the RHYTHM

track button while holding the [DELETE] button. This cancels all the in-

struments in the original rhythm track, leaving only a metronome sound

(the metronome sound will not be heard while the rhythm is playing). The

rhythm pattern can be up to 8 measures long (see “1. CUSTOM ACCOMP.

Measure/Beat” on page 19), and the pattern will continue to repeat so you

can add new instruments during each repeat, if necessary.

To Cancel A Single Percussion Instrument

Although you can cancel all instruments in the RHYTHM track by pressing

the RHYTHM track button while holding the [DELETE] button, it is also

possible to cancel a single instrument to eradicate a mistake or simply

eliminate an unwanted instrument. While holding the CANCEL key (the

highest key on the PSR-5700 keyboard), press the percussion key corre-

sponding to the instrument you want to cancel. The selected instrument

should now be cleared from the pattern.

If you can’t cancel an instrument even after following the above procedure,

switch to VOICE SELECT number 8 or 9 and try again.

To Add Accents

To accent specific beats after recording the rhythm, press the accent key

(the second to highest key on the keyboard, with the “>” symbol) at the

timing of beats you want to accent.

After the RHYTHM track has been programmed (or it can be left as it is

if no changes are required), you can select a bass or chord track for pro-

gramming by pressing the BASS or a CHORD track button while holding

the [RECORD] button (tracks containing preset data cannot be selected for

recording). The RHYTHM track will automatically switch to the PLAY

mode when a new REC track is specified. Please remember that only one

track can be programmed at a time.

prf

RECORD DELETE EDIT

CHORD 1 CHORD 2 CHORD 3 CHORD 4 CHORD 5 CHORD 6 BASS RHYTHM

1 2 3 4 5 6 7 ACCOMP.

PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC

>

CANCEL

HINT

B

Program the Bass and Chord

Parts

17

prf

RECORD DELETE EDIT

CHORD 1 CHORD 2 CHORD 3 CHORD 4 CHORD 5 CHORD 6 BASS RHYTHM

1 2 3 4 5 6 7 ACCOMP.

PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC PLAY REC

Play notes or chords to be added to the existing data, or delete all data on

the track (press the track button while holding the [DELETE] button) and

start from scratch. The bass and chord tracks must be programmed in the

key of C major!

Continue selecting new record tracks and variations, and program until

your custom accompaniment is complete.

Unwanted tracks can be deleted from the accompaniment by holding the [DE-

LETE] button and pressing the appropriate track button.

Although the bass and chord tracks must be programmed in C major, they are

automatically re-harmonized when the custom accompaniment is used in the

play mode, and can be used in any key, major or minor.

When programming an accompaniment from scratch, you can select a new

voice that will take effect from the beginning of the accompaniment after delet-

ing all tracks. Other voice changes added while programming will take effect

from the point at which they are made.

The synchro start, start, and stop functions can be used when recording a

custom accompaniment. The re-start function, however, cannot be used.

Pitch bend, modulation, and sustain changes are not recorded if the accompa-

niment is stopped — the accompaniment must be running for parameter

changes to be recorded.

The Custom Accompaniment Programmer memory capacity is limited. When

the available memory for the track you are recording is exhausted, the “Work

Area Full !!” display will appear and further recording on that track will be impos-

sible unless existing data is deleted. Further, if the data size is too big when you

perform a save operation, “Memory Area Full!!/ Can not Save” will appear on

the display.

Only preset voices 00 through 89 can be used to record bass and chord parts

(custom voices cannot be used).

If necessary, set a new default tempo for the custom accompaniment by

using the TEMPO [-] and [+] buttons.

Work Area Full !!

Memory Area Full!!

Can not Save

HINT

DETAIL

NSet a New Default Tempo

DETAIL

The Custom Accompaniment Programmer

18

+– +–

SAVE ßCancel´

Set to=Cus0 No Yes

+– +–

¢NAME

Big Band

_

SAVE TO ACCOMP.

Set to=Cus0 -Execute-

+– +–

The Custom Accompaniment Programmer

M

Give the Finished Accompa-

niment a Name and Assign it

to a CUSTOM Number

Use the “4. NAME” function described on page 20 to give your custom

accompaniment an original name, then use the “5. SAVE TO ACCOMP.”

function described on page 20 to assign the accompaniment to a CUSTOM

number and exit from the Custom Accompaniment Programmer mode.

Please note that if you attempt to exit from the Custom Accompaniment Pro-

grammer by pressing the [EXIT], [SEQUENCER], or [CUSTOM ACCOMP PRO-

GRAMMER] button, the confirmation display shown to the left will appear:

Use the left [-] and [+] buttons to select the custom accompaniment

number to which the accompaniment is to be stored (C0 through C5), then

press the [+] button under “YES” on the display to store the accompani-

ment. Press the [-] button under “NO” on the display to exit from the Cus-

tom Accompaniment Programmer without storing the data. You can also

press both the [-] and [+] buttons simultaneously to cancel the store opera-

tion and return to the Custom Accompaniment Programmer if you want to

make a few more changes or additions to the accompaniment before storing.

IMPORTANT

Using a Custom Accompaniment

HINT

IMPORTANT

STYLE SELECT

0 DISK12345

NUMBER

0 CUSTOM12345

BANK

Once created and stored, your original accompaniment can be selected

and used in the same way as the preset accompaniment styles.

Press the [CUSTOM] button and then the appropriate STYLE SELECT

NUMBER button (0 through 5) to select a custom accompaniment — C0,

C1, C2, C3, C4, or C5. The selected custom accompaniment can then be

operated just like any of the preset accompaniment styles — it can be

started and stopped as usual, and can be used in the FINGERED or SIN-

GLE FINGER AUTO BASS CHORD modes.

To select a preset accompaniment style after selecting a custom accompani-

ment, use the STYLE SELECT buttons in the normal way.

Interactive Accompaniment cannot be used with custom accompaniments.

19

Custom Accompaniment Editing

The PSR-5700 Custom Accompaniment Programmer offers a range of functions that let

you modify the recorded data in a number of ways. The various Custom Accompaniment

Programmer functions are accessed by using the [s] and [t] buttons, while the various

display screens provided by each function are accessed by using the [<] and [>] buttons.

1 CUSTOM ACCOMP. (Measure/Beat)

+– +–

`CUSTOM ACCOMP. Normal

Measure:4 Beat:4

2 VOLUME

+– +–

“VOL. 1~2~3~4~5~6~B~R~

15/15/15/15/15/15/15/15

_

Procedure:

Use the left [-] and [+] buttons to specify the numbers of

measures the accompaniment is to have (from 1 to 8), and

the right [-] and [+] buttons to specify the number of beats

per measure — from “3” to “5”.

Notes:

These parameters can only be changed when you’re creat-

ing an entirely new pattern from scratch — i.e. you have

deleted all tracks from the original accompaniment by hold-

ing the [DELETE] button and pressing the buttons of all

tracks containing data so that no PLAY indicators remain lit.

The INTRO, FILL, and ENDING variations must also be

empty.

FILL patterns can have a maximum length of 1 measure.

Purpose:

This display page allows the length (in measures) and time

signature of the accompaniment to be defined when the Cus-

tom Accompaniment mode is initially engaged.

Procedure:

Use the [<] and [>] buttons to position the cursor at the

volume parameter of the track you want to adjust (1 through

6, “B” for BASS, and “R” for RHYTHM, from left to right),

then use either the left or right [-] and [+] buttons to set the

volume to a value between “0” (minimum volume — no

sound) and “15” (maximum volume). Vertical bar-graphs to

the right of each track number on the top line of the display

provide a graphic representation of the track volume levels.

Notes:

Only tracks that contain data are available for volume

control.

Purpose:

This page lets you independently set the volume of each of

the Custom Accompaniment Programmer’s tracks.

The Custom Accompaniment Programmer

20

+– +–

¢NAME

Big Band

_

The Custom Accompaniment Programmer

3 FADER SELECT

+– +–

£FADER SELECT

C1` C2` C3` C4“ C5“ C6“

—

4 NAME

5 SAVE TO ACCOMP.

+– +–

SAVE TO ACCOMP.

Set to=Cus0 -Execute-

Procedure:

Use the [<] and [>] buttons to position the cursor at the

chord track you want to assign (C1 through C6), then use the

left or right [-] and [+] buttons to assign either “1” (the

CHORD 1 volume control) or “2” (the CHORD 2 volume

control) to the selected chord track.

Notes:

It is a good idea to group the chord tracks according to

their musical function. For example, tracks containing basic

block chords could be assigned to the CHORD 1 control

while tracks containing more “decorative” chord work could

be assigned to the CHORD 2 control.

Purpose:

Assigns the CHORD 1 and CHORD 2 volume controls to

Custom Accompaniment Programmer CHORD tracks 1

through 6, determining which control affects which chord

tracks when the accompaniment is played back.

Procedure:

Use the [<] and [>] buttons to move the underline cursor

to the various character positions, then use the left [-] and [+]

buttons to select the required character for each position.

Notes:

Independent names can not be assigned to INTRO, FILL,

and ENDING patterns. Here’s a list of the characters that can

be selected via the left [-] and [+] buttons.

Character list

[Space]!"#$%&'()*+,-./0123456789:;<=>?@

ABCDEFGHIJKLMNOPQRSTUVWXYZ[\]^_`

abcdefghijklmnopqrstuvwxyz{|}≤≥

Purpose:

Allows a name of up to 8 characters to be assigned to the

current custom accompaniment before it is stored via the

following “5. SAVE TO ACCOMP.” function.

Procedure:

The “Set to” parameter in the first display screen deter-

mines to which custom accompaniment number the accom-

paniment will be stored — Cus0, Cus1, Cus2, Cus3, Cus4, or

Cus5. When the “Set to” parameter has been set as required

by using the left [-] and [+] buttons, press the right [-] and

[+] buttons under “-Execute-” on the display to actually store

the current custom accompaniment in the specified custom

accompaniment number. “Completed” will appear when the

operation is complete.

Purpose:

This function stores the current custom accompaniment to

a specified custom accompaniment number.

Страница загружается...

Yamaha psr-5700 Инструкция по применению

Похожие модели бренда

Модели других брендов