ABB 361A-5 Quick Installation Manual

English . . . . . . . . .3

English – USA . . .9

Dansk . . . . . . . . .17

Deutsch . . . . . . .23

Español . . . . . . .29

Suomi. . . . . . . . .37

Français. . . . . . .43

Italiano. . . . . . . .49

Nederlands . . . .55

Polski . . . . . . . . .61

Português . . . . .67

Русский . . . . . . .73

Svenska . . . . . . .81

Türkçe . . . . . . . .87

中文. . . . . . . . . . .93

—

ABB INDUSTRIAL DRIVES

ACS880-01 drives

Frames R6 to R9

Quick installation guide

3AUA0000099689 Rev G MUL

E

FFECTIVE: 2019-05-08

EN

USA

DA

DE

ES

FI

FR

IT

NL

PL

PT

RU

SV

TR

ZH

—

List of related manuals

You can find manuals and other product documents in PDF format on the

Internet. See section Document library on the Internet on the inside of the

back cover. For manuals not available in the Document library, contact your

local ABB representative.

The code below opens an online listing of the manuals applicable to the

product:

Drive hardware manuals and guides Code (English)

ACS880-01 hardware manual 3AUA0000078093

ACS880-01 quick installation guide for frames

R1 to R3

3AUA0000085966

ACS880-01 quick installation guide for frames

R4 and R5

3AUA0000099663

ACS880-01 quick installation guide for frames

R6 to R9

3AUA0000099689

ACS880-01 +P940 drives for cabinet

installation supplement

3AUA0000145446

ACS880-01 assembly drawings for cable entry

boxes of IP21 frames R5 to R9

3AUA0000119627

ACS-AP-x assistant control panels user’s

manual

3AUA0000085685

Vibration dampers for ACS880-01 drives

(frames R4 and R5, option +C131) installation

guide

3AXD50000010497

Vibration dampers for ACS880-01 drives

(frames R6 to R9, option +C131) installation

guide

3AXD50000013389

ACS880-01 +C132 marine type-approved drives

supplement

3AXD50000010521

ACS880-01 +N7502 drives for SynRM motors

(0.8 to 200 kW) supplement

3AXD50000029482

Drive firmware manuals and guides

ACS880 primary control program firmware

manual

3AUA0000085967

Quick start-up guide for ACS880 drives with

primary control program

3AUA0000098062

Option manuals and guides

Manuals and quick guides for I/O extension

modules, fieldbus adapter, etc.

ACS880-01 manuals

EN – Quick installation guide 3

EN

DA

DE

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

EN – Quick installation guide

This guide instructs briefly how to install the drive. For more detailed instructions,

engineering guide lines, technical data and complete safety instructions, see the

hardware manual (www.abb.com/drives

: Select Document Library and search for

document number 3AUA0000078093 [English]).

Obey the safety instructions

The floor material below the drive must be non-flammable.

Check if capacitors need to be reformed

Reform the capacitors if the drive has not been powered (either in storage or unused)

for a year or more.

You can determine the manufacturing date from the serial number, which you find on

the type designation label attached to the drive. The serial number is of format

MYYWWRXXXX. YY and WW tell the manufacturing year and week as follows:

YY: 17, 18, 19, … for 2017, 2018, 2019,

…

WW: 01, 02, 03, … for week 1, week 2, week 3, …

For information on reforming the capacitors, see Converter modules with

electrolytic DC capacitors in the DC link capacitor reforming instructions

WARNING! Obey these instructions. If you ignore them, injury or death, or

damage to the equipment can occur:

• Only qualified electrical professionals are allowed to install and maintain the

drive.

• Never work on the drive, motor cable or motor when main power is applied. If

the drive is already connected to the input power, wait for 5 minutes after

disconnecting the input power.

• Never work on the control cables when power is applied to the drive or to the

external control circuits.

• Always ground the drive, the motor and adjoining equipment to the protective

earth (PE) bus of the power supply.

• Make sure that debris from borings and grindings does not enter the drive when

installing.

• Do not connect the drive to a voltage higher than what is marked on the type

designation label.

4 EN – Quick installation guide

EN

DA

DE

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

(3BFE64059629 [English]), available on the Internet at

www.abb.com/drives/documents.

Select the power cables

Size the power cables according to local regulations to carry the nominal current

given on the type designation label of your drive.

Typical power cable sizes are listed in table B on page 102. For the conditions of the

sizing, see the hardware manual.

Ensure the cooling

See table B on page 102 for the losses and the cooling air flow through the drive. The

allowed operating temperature range of the drive without derating is -15 to +40 °C.

Protect the drive and input power cables

See table B on page 102.

Install the drive on the wall

See figure A on page 101.

Check the compatibility with IT (ungrounded), corner-

grounded delta, midpoint-grounded delta and TT systems

The standard drive with ground-to-phase varistors connected can be installed to a

symmetrically grounded TN-S system. For other systems, see the hardware manual

and ACS880 frames R1 to R11 EMC filter and ground-to-phase varistor

disconnecting instructions (3AUA0000125152 [English]).

EN – Quick installation guide 5

EN

DA

DE

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

.

A = TN-S system, B1 = Corner-grounded system, B2 = Midpoint-grounded system, C = IT system

WARNING! Do not install the drive with EMC filter options +E200 and +E202

connected to a system that the filter is not suitable for. This can cause danger,

or damage the drive.

WARNING! Do not install the drive with the ground-to-phase varistor

connected to a system that the varistor is not suitable for. If you do, the varistor

circuit can be damaged. See the drive hardware manual.

Note: With option +E201, remove EMC AC, EMC DC and VAR screws in for systems

other than TN-S if not removed at the factory. For more information, contact ABB.

Check the insulation of the input and motor cables and the

motor

Check the insulation of the input cable according to local regulations before you

connect it to the drive.

See figure D on page 103. Ground the motor cable shield at the motor end. For

minimal interference, make a 360-degree grounding at the cable lead-through, or

keep the pig tail short.

PE

N

L3

L2

L1

PE

L3

L2

L1

L3

L2

L1

PE

L3

L2

L1

B1 CA

B2

6 EN – Quick installation guide

EN

DA

DE

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

Check the insulation of the motor cable and motor when the cable is disconnected

from the drive, see figure E on page 103. Measure the insulation resistance between

each phase conductor and the Protective Earth conductor using a measuring voltage

of 1000 V DC. The insulation resistance of an ABB motor must exceed 100 Mohm

(reference value at 25 °C or 77 °F). For the insulation resistance of other motors,

please consult the manufacturer’s instructions. Note: Moisture inside the motor

casing will reduce the insulation resistance. If moisture is suspected, dry the motor

and repeat the measurement.

Attach the warning stickers in local languages

Connect the power cables

See figures C and F on pages 102 and 103. Use symmetrical shielded cable for the

motor cabling.

1. Remove the front cover. IP21 units

: Release the retaining clip with a screwdriver

(a) and lift the cover from the bottom outwards (b).

2. IP21 units

: Remove the cable entry box cover by undoing the mounting screws.

3. Attach the residual voltage warning sticker in the local language next to the

control unit.

4. Remove the side plates of the cable entry box.

5. Remove the shroud on the power cable terminals by releasing the clips on the

sides with a screwdriver and lifting (a). Knock out holes for the cables (b).

6. For frames R8 and R9:

If parallel cables are installed, knock out the shrouds on

the power cable terminals for the cables to be installed.

7. Cut adequate holes into the rubber grommets. Slide the grommets onto the

cables. Prepare the cable ends. Slide the cables through the holes of the bottom

plate and attach the grommets to the holes.

8. Ground the cable shields 360 degrees under the grounding clamps.

9. Connect the twisted cable shields to the grounding terminals.

10. Connect the conductors of the input and motor cables. Tighten the screws.

11. Units with option +D150:

Connect the conductors of the brake resistor cable to the

R+ and R- terminals.

12. If parallel cables are installed

, install the grounding shelf for them. Repeat steps 7

to 12.

13. Reinstall the shroud on the power terminals.

14. Reinstall the side plates of the cable entry box.

15. Secure the cables outside the unit mechanically.

EN – Quick installation guide 7

EN

DA

DE

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

Connect the control cables

See figure G.

1. Install the control cable grounding shelf in the cable entry box.

2. Cut adequate holes into the rubber grommets and slide the grommets onto the

cables. Slide the cables through the holes of the bottom plate and attach the

grommets to the holes.

3. Strip the cable ends and cut to suitable length (note the extra length of the

grounding conductors).

4. Ground the outer shields of all control cables 360 degrees at a grounding clamp in

the cable entry box.

5. Ground the pair-cable shields to a grounding clamp below the control board.

Leave the other end of the shields unconnected or ground them indirectly via a

high-frequency capacitor with a few nanofarads, eg, 3.3 nF / 630 V.

6. Connect the conductors to the appropriate terminals of the control board (see

page 8).

7. Wire the optional modules if included in the delivery.

8. Reinstall the front cover.

Note for fieldbus cabling. See figure H.

1. Install the additional grounding shelf.

2. Ground the outer shields of the cables 360 degrees at a grounding clamp.

3. Knock out holes in the cable entry box cover for the cables to be installed. Install

the cable entry box cover.

4. Plug the connector to the fieldbus module.

Default I/O connections

The default I/O connections of the Factory macro of the ACS880 primary control

program are shown below.

8 EN – Quick installation guide

EN

DA

DE

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

XPOW External power input

1 +24VI

24 V DC, 2 A

2 GND

XAI Reference voltage and analog inputs

1 +VREF 10 V DC, R

L

1…10 kohm

2 -VREF -10 V DC, R

L

1…10 kohm

3 AGND Ground

4 AI1+ Speed reference 0(2)…10 V, R

in

>

200 kohm

5 AI1-

6 AI2+

By default not in use. 0(4)…20 mA, R

in

=

100 ohm

7 AI2-

J1 J1 AI1 current/voltage selection jumper

J2 J2 AI2 current/voltage selection jumper

XAO Analog outputs

1 AO1 Motor speed rpm 0…20 mA, R

L

<

500 ohm

2 AGND

3 AO2

Motor current 0…20 mA, R

L

< 500 ohm

4 AGND

XD2D Drive-to-drive link

1 B

Drive-to-drive link

2 A

3 BGND

J3 J3 Drive-to-drive link termination switch

XRO1, XRO2, XRO3 Relay outputs

11 NC

Ready

250 V AC / 30 V DC

2 A

12 COM

13 NO

21 NC

Running

250 V AC / 30 V DC

2 A

22 COM

23 NO

31 NC

Faulted(-1)

250 V AC / 30 V DC

2 A

32 COM

33 NO

XD24 Digital interlock

1 DIIL Run enable

2 +24VD +24 V DC 200 mA

1)

3 DICOM Digital input ground

4 +24VD +24 V DC 200 mA

1)

5 DIOGND Digital input/output ground

J6 Ground selection switch

XDIO Digital input/outputs

1 DIO1 Output: Ready

2 DIO2 Output: Running

XDI Digital inputs

1 DI1 Stop (0) / Start (1)

2 DI2 Forward (0) / Reverse (1)

3 DI3 Reset

4 DI4 Acceleration & deceleration select

5 DI5 Constant speed 1 (1 = On)

6 DI6 By default not in use.

XSTO Safe torque off

1 OUT1

Safe torque off. Both circuits must be

closed for the drive to start.

2 SGND

3 IN1

4 IN2

X12 Safety functions module connection

X13 Control panel connection

X205 Memory unit connection

Wire sizes:

0.5 … 2.5 mm

2

(24…12 AWG)

Tightening

torques: 0.5 N·m

(5 lbf·in) for both

stranded and

solid wiring.

1)

Total load

capacity of these

outputs is 4.8 W

(200 mA / 24 V)

minus the power

taken by DIO1 and

DIO2.

Fault

EN – USA quick installation guide 9

DA

USA

DA

DE

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

EN – USA quick installation guide

This guide instructs briefly how to install the drive. For more detailed instructions,

engineering guide lines, technical data and complete safety instructions, see the

hardware manual (www.abb.com/drives

: Select Document Library and search for

document number 3AUA0000078093 [English]).

Obey the safety instructions

The floor material below the drive must be non-flammable.

Check if capacitors need to be reformed

Reform the capacitors if the drive has not been powered (either in storage or unused)

for a year or more.

You can determine the manufacturing date from the serial number, which you find on

the type designation label attached to the drive. The serial number is of format

MYYWWRXXXX. YY and WW tell the manufacturing year and week as follows:

YY: 17, 18, 19, … for 2017, 2018, 2019,

…

WW: 01, 02, 03, … for week 1, week 2, week 3, …

For information on reforming the capacitors, see Converter modules with

electrolytic DC capacitors in the DC link capacitor reforming instructions

WARNING! Obey these instructions. If you ignore them, injury or death, or

damage to the equipment can occur:

• Only qualified electrical professionals are allowed to install and maintain the

drive.

• Never work on the drive, motor cable or motor when main power is applied. If

the drive is already connected to the input power, wait for 5 minutes after

disconnecting the input power.

• Never work on the control cables when power is applied to the drive or to the

external control circuits.

• Always ground the drive, the motor and adjoining equipment to the protective

earth (PE) bus of the power supply.

• Make sure that debris from borings and grindings does not enter the drive when

installing.

• Do not connect the drive to a voltage higher than what is marked on the type

designation label.

10 EN – USA quick installation guide

DA

USA

DA

DE

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

(3BFE64059629 [English]), available on the Internet at

www.abb.com/drives/documents.

Select the power cables

Size the power cables according to local regulations to carry the nominal current

given on the type designation label of your drive.

Typical power cable sizes are listed in table B on page 102. For the conditions of the

sizing, see the hardware manual.

Ensure the cooling

See table A on page 105 for the losses and the cooling air flow through the drive. The

allowed operating temperature range of the drive without derating is -15 to +40 °C.

Protect the drive and input power cable

See table A on page 105 for the UL class T fuses for branch circuit protection per

NEC. Check that the operating time of the fuse is below 0.5 seconds for frame R6

and below 0.1 seconds for frames R7 to R9. Obey local regulations.

Install the drive on the wall

See figure A on page 101. For UL Type 12 drives: Install also the hood to the drive.

Check the compatibility with IT (ungrounded), corner-

grounded delta, midpoint-grounded delta and TT systems

The standard drive with ground-to-phase varistors connected can be installed to a

symmetrically grounded TN-S system. For other systems, see the hardware manual

and ACS880 frames R1 to R11 EMC filter and ground-to-phase varistor

disconnecting instructions (3AUA0000125152 [English]).

EN – USA quick installation guide 11

DA

USA

DA

DE

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

A = TN-S system, B1 = Corner-grounded system, B2 = Midpoint-grounded system, C = IT system

WARNING! Do not install the drive with EMC filter options +E200 and +E202

connected to a system that the filter is not suitable for. This can cause danger,

or damage the drive.

WARNING! Do not install the drive with the ground-to-phase varistor

connected to a system that the varistor is not suitable for. If you do, the varistor

circuit can be damaged. See the drive hardware manual.

Note: With option +E201, remove EMC AC, EMC DC and VAR screws in for systems

other than TN-S if not removed at the factory. For more information, contact ABB.

Check the insulation of the input and motor cables and the

motor

Check the insulation of the input cable according to local regulations before

connecting it to the drive.

Check the insulation of the motor cable and motor when the cable is disconnected

from the drive, see figure D on page 105. Measure the insulation resistance between

each phase conductor and the Protective Earth conductor using a measuring voltage

of 1000 V DC. The insulation resistance of an ABB motor must exceed 100 Mohm

(reference value at 25 °C or 77 °F). For the insulation resistance of other motors,

PE

L3

L2

L1

L3

L2

L1

PE

L3

L2

L1

B1 C

B2

PE

L2

L3

L1

N

A

12 EN – USA quick installation guide

DA

USA

DA

DE

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

please consult the manufacturer’s instructions. Note: Moisture inside the motor

casing will reduce the insulation resistance. If moisture is suspected, dry the motor

and repeat the measurement.

Connect the power cables

See figures B, C and E on pages 105 and 106. Use symmetrical shielded cable for

the motor cabling.

1. Remove the front cover. UL Type 1 drives:

Release the retaining clip with a

screwdriver (a) and lift the cover from the bottom outwards (b).

2. UL Type 1 drives:

Remove the cable entry box cover by undoing the mounting

screws.

3. Attach the residual voltage warning sticker in the local language next to the

control board top.

4. Remove the side plates of the cable entry box.

5. Remove the shroud on the power cable terminals by releasing the clips on the

sides with a screwdriver and lifting (a). If parallel cables are installed

, knock out

holes for the cables (b).

6. Knock out the shrouds on the power cable terminals for the cables to be installed.

7. Fasten the cable conduits to the cable lead-through plate holes. Strip the cable

ends. Slide the cables through the connectors.

8. Connect the twisted cable shields to the grounding terminals.

9. Connect the conductors of the input and motor cables. Tighten the screws.

10. Units with option +D150:

Connect the conductors of the brake resistor cable to the

R+ and R- terminals.

11. Reinstall the shroud on the power terminals.

12. Reinstall the side plates of the cable entry box.

13. Secure the cables outside the unit mechanically.

Connect the control cables

Install the control cable grounding shelf in the cable entry box (see figure F on page

106).

See figure G on page 106.

EN – USA quick installation guide 13

DA

USA

DA

DE

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

1. Fasten the cable conduits to the cable lead-through plate holes. Slide the cables

through the connectors.

2. Strip the cable ends and cut to suitable length (note the extra length of the

grounding conductors).

3. Ground the outer shields of all control cables 360 degrees at a grounding clamp in

the cable entry box.

4. Ground the pair-cable shields to a grounding clamp below the control board.

Leave the other end of the shields unconnected or ground them indirectly via a

high-frequency capacitor with a few nanofarads, eg, 3.3 nF / 630 V.

5. Connect the conductors to the appropriate terminals of the control board (see

page 14).

6. Wire the optional modules if included in the delivery. For fieldbus modules, see

figure H on page 104

7. Reinstall the front covers.

Default I/O connections

The default I/O connections of the Factory macro of the ACS880 primary control

program are shown below.

14 EN – USA quick installation guide

DA

USA

DA

DE

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

XPOW External power input

1 +24VI

24 V DC, 2 A

2 GND

XAI Reference voltage and analog inputs

1 +VREF 10 V DC, R

L

1…10 kohm

2 -VREF -10 V DC, R

L

1…10 kohm

3 AGND Ground

4 AI1+ Speed reference 0(2)…10 V, R

in

>

200 kohm

5 AI1-

6 AI2+

By default not in use. 0(4)…20 mA, R

in

=

100 ohm

7 AI2-

J1 J1 AI1 current/voltage selection jumper

J2 J2 AI2 current/voltage selection jumper

XAO Analog outputs

1 AO1 Motor speed rpm 0…20 mA, R

L

<

500 ohm

2 AGND

3 AO2

Motor current 0…20 mA, R

L

< 500 ohm

4 AGND

XD2D Drive-to-drive link

1 B

Drive-to-drive link

2 A

3 BGND

J3 J3 Drive-to-drive link termination switch

XRO1, XRO2, XRO3 Relay outputs

1 NC

Ready

250 V AC / 30 V DC

2 A

2 COM

3 NO

1 NC

Running

250 V AC / 30 V DC

2 A

2 COM

3 NO

1 NC

Faulted(-1)

250 V AC / 30 V DC

2 A

2 COM

3 NO

XD24 Digital interlock

1 DIIL Run enable

2 +24VD +24 V DC 200 mA

1)

3 DICOM Digital input ground

4 +24VD +24 V DC 200 mA

1)

5 DIOGND Digital input/output ground

J6 Ground selection switch

XDIO Digital input/outputs

1 DIO1 Output: Ready

2 DIO2 Output: Running

XDI Digital inputs

1 DI1 Stop (0) / Start (1)

2 DI2 Forward (0) / Reverse (1)

3 DI3 Reset

4 DI4 Acceleration & deceleration select

5 DI5 Constant speed 1 (1 = On)

6 DI6 By default not in use.

XSTO Safe torque off

1 OUT1

Safe torque off. Both circuits must be

closed for the drive to start.

2 SGND

3 IN1

4 IN2

X12 Safety functions module connection

X13 Control panel connection

X205 Memory unit connection

Wire sizes:

0.5 … 2.5 mm

2

(24…12 AWG)

Tightening

torques: 0.5 N·m

(5 lbf·in) for both

stranded and

solid wiring.

1)

Total load

capacity of these

outputs is 4.8 W

(200 mA / 24 V)

minus the power

taken by DIO1 and

DIO2.

Fault

EN – USA quick installation guide 15

DA

USA

DA

DE

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

UL checklist

• Use the drive in a heated, indoor controlled environment. The drive must be

installed in clean air according to enclosure classification. Cooling air must be

clean, free from corrosive materials and electrically conductive dust.

• The maximum ambient air temperature is 40 °C (104 °F) at rated current. The

current is derated for 40 to 55 °C (104 to 131 °F).

• The drive is suitable for use in a circuit capable of delivering not more than

100,000 rms symmetrical amperes, 600 V maximum. The ampere rating is based

on tests done according to UL 508C.

• The cables located within the motor circuit must be rated for at least 75 °C

(167 °F) in UL-compliant installations.

• The input cable must be protected with fuses. Circuit breakers must not be used

without fuses in the USA. Suitable IEC (class aR) fuses and UL (class T) fuses

are listed in the hardware manual. For suitable circuit breakers, contact your local

ABB representative.

• For installation in the United States, branch circuit protection must be provided in

accordance with the National Electrical Code (NEC) and any applicable local

codes. To fulfill this requirement, use the UL classified fuses.

• For installation in Canada, branch circuit protection must be provided in

accordance with the Canadian Electrical Code and any applicable provincial

codes. To fulfill this requirement, use the UL classified fuses.

• The drive provides overload protection in accordance with the National Electrical

Code (NEC).

16 EN – USA quick installation guide

DA

USA

DA

DE

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

DA – Hurtig installationsvejledning 17

EN

DA

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

DA – Hurtig installationsvejledning

Denne guide er en kortfattet vejledning i, hvordan du installerer frekvensomformeren.

Hvis du vil have mere detaljerede instruktioner, tekniske retningslinjer, tekniske data

og komplette sikkerhedsinstruktioner, kan du se hardwaremanualen

(www.abb.com/drives

: Vælg Document Library, og søg efter dokumentnummer

3AUA0000078093 (på engelsk).

Overhold sikkerhedsinstruktionerne

Gulvmaterialet under frekvensomformeren skal være ikke-brandbart.

Kontrollér, om det er nødvendigt at reformere

kondensatorerne

Reformér kondensatorerne, hvis frekvensomformeren ikke har været tilsluttet strøm i

over et år (opbevaret eller ikke anvendt).

Du kan bestemme produktionsdatoen ud fra serienummeret, som du finder på

mærkatet med typebetegnelse på frekvensomformeren. Serienummeret har formatet

MYYWWRXXXX. YY og WW angiver produktionsåret og ugen på følgende måde:

YY: 17, 18, 19, … for 2017, 2018, 2019,

…

WW: 01, 02, 03, … for uge 1, uge 2, uge 3, …

ADVARSEL! Følg disse instruktioner. Hvis de ignoreres, kan det resultere i

personskader, dødsfald eller skade på udstyret:

• Kun autoriserede elinstallatører må udføre installation og vedligeholdelse af

frekvensomformeren.

• Undlad at arbejde med frekvensomformeren, motorkablet eller motoren, når

tilslutning til nettet er foretaget. Hvis frekvensomformeren allerede er tilsluttet

netforsyningen, skal du vente 5 minutter efter frakobling af netspændingen.

• Du må aldrig arbejde med signalkablerne, når netspændingen er tilsluttet

frekvensomformeren eller de eksterne styrekredse.

• Frekvensomformeren, motoren og tilstødende udstyr skal altid jordes med

strømforsyningens beskyttelsesjordbus (PE).

• Undgå, at der trænger smuds fra boringer og sliberester ind i

frekvensomformeren under installation.

• Frekvensomformeren må ikke tilsluttes til en spænding, der er højere end den,

der er angivet på mærkatet med typebetegnelse.

18 DA – Hurtig installationsvejledning

EN

DA

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

Oplysninger om reformering af kondensatorer findes i Converter modules with

electrolytic DC capacitors in the DC link capacitor reforming instructions

(3BFE64059629 (på engelsk)), som findes på internettet på

www.abb.com/drives/documents

.

Vælg effektkabler

Vælg en størrelse til kablerne i henhold til lokale forskrifter til at bære den nominelle

strøm, der er anført på mærkatet med typebetegnelsen på din frekvensomformer.

Typiske størrelser på netkabler er vist i tabellen B på side 102. Se hardwaremanualen

for oplysninger om betingelserne for størrelse.

Sørg for kølingen

Se tabel B på side 102 for tabene og frekvensomformerens gennemstrømning af

kølende luft. Frekvensomformerens tilladte driftstemperaturområde uden reduktion er

-15 til +40 °C.

Beskyt frekvensomformeren og forsyningskablet

Se tabellen B på side 102.

Installer frekvensomformeren på væggen

Se figur A på side 101.

Kontrollér kompatibiliteten med IT-net (ujordede),

hjørnejordede delta-, midtpunktsjordet delta- og

TT-systemer

Standardfrekvensomformeren med tilsluttet jord-til-fase-varistorer kan installeres

sammen med et symmetrisk jordet TN-S-system. Oplysninger om andre systemer

finder du i hardwaremanualen samt i ACS880 frames R1 to R11 EMC filter and ground-

to-phase varistor disconnecting instructions (3AUA0000125152 (på engelsk)).

DA – Hurtig installationsvejledning 19

EN

DA

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

A = TN-S-system, B1 = Hjørnejordet system, B2 = Midtpunktsjordet system, C = IT-system

ADVARSEL! Installer ikke en frekvensomformer med tilsluttet EMC-filter

ekstraudstyr +E200 og +E202 til et system, hvortil filtret ikke er egnet. Dette

kan medføre fare eller ødelægge frekvensomformeren.

ADVARSEL! Installer ikke frekvensomformeren med tilsluttet jord-til-fase-

varistor til et system, hvortil varistoren ikke er egnet. Hvis du gør det, kan

varistorkredsløbet tage skade. Se frekvensomformerens hardwaremanual.

Bemærk! Hvis du anvender ekstraudstyr +E201, skal du fjerne EMC AC-, EMC DC-

og VAR-skruerne i andre systemer end TN-S, hvis de ikke allerede er fjernet på

fabrikken. Kontakt ABB for at få yderligere oplysninger.

Kontroller isoleringen på forsynings- og motorkabel samt

motoren

Kontrollér, at isoleringen af forsyningskablet er i overensstemmelse med de nationale

forskrifter, inden du tilslutter det til frekvensomformeren.

Se figur D på side 103. Tilslut motorkablets skærm i motoren. Opnå minimal

interferens ved at lave en 360 graders jording ved kabelgennemføringen eller holde

den snoede kobberskærm kort.

PE

N

L3

L2

L1

PE

L3

L2

L1

L3

L2

L1

PE

L3

L2

L1

B1 CA

B2

20 DA – Hurtig installationsvejledning

EN

DA

ES

FI

FR

IT

NL

PT

RU

SV

TR

CN

Kontrollér isoleringen af motorkabel og motor, når kablet er koblet fra

frekvensomformeren. Se figur E på side 103. Mål isolationsmodstanden mellem hver

faseleder og beskyttelsesjordens leder med en målespænding på 1000 V DC.

Isolationsmodstanden på en ABB-motor skal være større end 100 Mohm

(referenceværdi ved 25 °C eller 77 °F). Se producentens instruktioner for at få

oplysninger om isolationsmodstanden på andre motorer. Bemærk! Fugt inden i

motorhuset reducerer isolationsmodstanden. Hvis der er mistanke om fugt, skal

motoren tørres, og målingen gentages.

Fastgør advarselsmærkaterne på de lokale sprog

Tilslut effektkablerne

Se figurerne C og F på siderne 102 og 103. Anvend et skærmet symmetrisk kabel til

motoren.

1. Fjern frontdækslet. IP21-enheder

: Løsn låsesplitten med en skruetrækker (a), og

løft dækslet udad fra bunden (b).

2. IP21-enheder

: Fjern dæksel for kabelsektion ved at løsne monteringsskruerne.

3. Fastgør advarselsmærkatet om restspænding på det lokale sprog ved siden af

styreenheden.

4. Fjern sidepladerne fra kabelindgangskassen.

5. Fjern afdækningen for effektkablernes terminaler ved at frigøre splitterne og løfte

afdækningen op fra siderne med en skruetrækker (a). Slå hullerne ud, hvor

kablerne skal installeres (b).

6. Til modulerne R8 og R9:

Hvis der er installeret parallelkabler, skal du slå

afskærmningerne ud på effektkabelterminalerne til de kabler, som skal installeres.

7. Skær tilstrækkeligt store huller i gummimufferne. Træk mufferne over på kablerne.

Forbered kabelenderne. Før kablerne gennem hullerne på bundpladen, og sæt

mufferne fast i hullerne.

8. Jord kabelskærmene 360 grader under jordingsklemmerne.

9. Tilslut de snoede kabelskærme til jordterminaler.

10. Forbind faselederne på forsynings- og motorterminalerne. Stram skruerne.

11. Enheder med ekstraudstyr +D150:

Forbind lederne i modstandskablet til

terminalerne R+ og R-.

12. Hvis der monteres parallelle kabler

, monteres jordingsplint til dem. Gentag trin 7-12.

13. Genmontér afskærmningen på effektterminalerne.

14. Montér sidepladerne på kabelsektionen.

15. Fastgør kablerne mekanisk uden for frekvensomformeren.

Страница загружается ...

ABB 361A-5 Quick Installation Manual

ABB 361A-5 Quick Installation Manual

на других языках

Похожие модели бренда

Модели других брендов