Yamaha CRX-B370 Инструкция по применению

CRX-B370

CD Receiver

CD-ресивер

Owner’s Manual

Руководство пользователя

EN

RU

English

Русский

2 En

Table of Contents

PRECAUTIONS ....................................................................................... 3

Introduction .......................................................................................... 7

About this manual ....................................................................................................................................... 7

Trademarks ....................................................................................................................................................... 7

Accessories ....................................................................................................................................................... 7

What you can do with this unit .......................................................... 8

Parts name ............................................................................................. 9

Front panel ....................................................................................................................................................... 9

Rear panel ...................................................................................................................................................... 10

Front panel display ................................................................................................................................... 11

Remote control ........................................................................................................................................... 12

Preparations ........................................................................................ 13

Connecting speakers .............................................................................................................................. 13

Connecting the antenna ...................................................................................................................... 14

Turning on the power ............................................................................................................................ 15

Using the sleep timer .............................................................................................................................. 15

Listening to music .............................................................................. 16

Listening to CDs ......................................................................................................................................... 16

Playing music on USB memory devices ...................................................................................... 17

Playing music via Bluetooth® connection ................................................................................. 18

Listening to FM radio stations ........................................................................................................... 19

Playing music from external devices ............................................................................................ 21

More on playback .............................................................................. 22

Shuffle/Repeat playback ....................................................................................................................... 22

Playback information ............................................................................................................................... 23

Adjusting sound quality ........................................................................................................................ 23

Option menu ................................................................................................................................................ 24

Troubleshooting ................................................................................ 25

General ............................................................................................................................................................. 25

Bluetooth ........................................................................................................................................................ 26

Disc ..................................................................................................................................................................... 27

USB memory devices ............................................................................................................................... 27

FM reception ................................................................................................................................................ 28

Messages in the front panel display ............................................................................................... 29

Supported devices/media and file formats .................................. 30

Supported devices/media ................................................................................................................... 30

File format ...................................................................................................................................................... 31

Specifications ..................................................................................... 32

En 3

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE USE. BE SURE TO

FOLLOW THESE INSTRUCTIONS.

The precautions listed below are to prevent risk of harm to the

user and others, as well as to prevent property damage, and to

help the user use this unit properly and safely. Be sure to follow

these instructions.

After reading this manual, be sure to keep it in a safe place where it can be

referenced at any time.

WARNING

This content indicates “risk of serious injury or death.”

Laser

• Do not remove the cover for repair. This unit uses a laser. Laser light entering your eyes

may cause visual impairment. Request inspections or repairs from the dealer where you

purchased the unit or from qualified Yamaha service personnel.

• Do not look into the laser source. If there is nothing to block it, this unit emits a visible laser.

Avoid looking at the laser directly. Laser light entering your eyes may cause visual

impairment. When the plug is inserted into the AC outlet, do not place your eyes near

openings of the disk tray or other openings, and do not try to look inside the unit.

Power supply/power cord

• Do not do anything that could damage the power cord.

- Do not place it near a heater.

- Do not bend it excessively or alter it.

- Do not scratch it.

- Do not place it under a heavy object.

Using the power cord with the core of the cord exposed could cause electric shocks or a

fire.

• Never charge this unit if it is wet. Failure to observe this may cause electric shocks or a

terminal circuit shortage and cause a fire or malfunctions.

• Do not touch the power plug or cord if there is a chance of lightning. Failure to observe this

may cause electric shocks.

• Use this unit with the power supply voltage printed on it. Failure to connect to an

appropriate AC outlet may cause a fire, electric shocks, or malfunctions.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it. Failure to observe this may cause a fire or electric shocks.

• When setting up the unit, make sure that the AC outlet you are using is easily accessible. If

some trouble or malfunction occurs, immediately turn off the power switch and disconnect

the plug from the AC outlet. Even when the power switch is turned off, as long as the power

cord is not unplugged from the wall AC outlet, the unit will not be disconnected from the

power source.

• If you hear thunder or suspect approaching lightning, quickly turn off the power switch and

pull the power plug from the AC outlet. Failure to observe this may cause a fire or

malfunctions.

• If not using the unit for long periods of time, be sure to pull the power plug from the AC

outlet. Failure to observe this may cause a fire or malfunctions.

Do not disassemble

• Do not disassemble or modify this unit. Failure to observe this may cause a fire, electric

shocks, injury, or malfunctions. If you notice any irregularities, be sure to request an

inspection or repair from the dealer where you purchased the unit or from qualified Yamaha

service personnel.

Water warning

• Do not expose the unit to rain, use it near water or in damp or wet conditions, or place on it

any containers (such as vases, bottles or glasses) containing liquids which might spill into

any openings or places where water may drop. A liquid such as water getting into the unit

may cause a fire, electric shocks, or malfunctions. If any liquid such as water seeps into the

device, turn off the power immediately and unplug the power cord from the AC outlet. Then,

request an inspection from the dealer where you purchased the unit or from qualified

Yamaha service personnel.

• Never insert or remove an electric plug with wet hands. Do not handle this unit with wet

hands. Failure to observe this may cause electric shocks or malfunctions.

Fire warning

• Do not place any burning items or open flames near the unit, since they may cause a fire.

• Be sure to request inspections or repairs from the dealer where you

purchased the unit or from qualified Yamaha service personnel.

• Yamaha cannot be held responsible for injury to you or damage of the

products caused by improper use or modifications to the unit.

• This product is for ordinary homes. Do not use for applications

requiring high reliability, such as managing lives, health care or high-

value assets.

4 En

Maintenance and care

• Do not use aerosols or spray-type chemicals that contain combustible gas for cleaning or

lubrication. The combustible gas will remain inside the unit, which may cause explosion or

fire.

Battery use

• Do not disassemble a battery. If the contents of the battery get on your hands or in your

eyes, it can cause blindness or chemical burns.

• Do not dispose of batteries in fire. Doing so may result in the battery bursting, causing a fire

or injury.

• Do not attempt to recharge batteries that are not intended to be charged. Charging could

cause the battery to burst or leak, which can cause blindness, chemical burns, or injury.

• If the batteries do leak, avoid contact with the leaked fluid. If the battery fluid should come in

contact with your eyes, mouth, or skin, wash immediately with water and consult a doctor.

Battery fluid is corrosive and may possibly cause loss of sight or chemical burns.

Wireless unit

• Do not use this unit near medical devices or inside medical facilities. Radio waves from this

unit may affect electro-medical devices.

• Do not use this unit within 15 cm (6 in) of persons with a heart pacemaker implant or a

defibrillator implant. Radio waves from this unit may affect electro-medical devices, such as

a heart pacemaker implant or defibrillator implant.

If you notice any abnormality

• If any of the following abnormalities occur, immediately turn off the power and disconnect

the power plug.

- The power cord/plug is damaged.

- An unusual smell or smoke is emitted from the unit.

- Foreign material gets into the interior of the unit.

- There is a loss of sound during use.

- There is a crack or damage in the unit.

Continued use could cause electric shocks, a fire, or malfunctions. Immediately request an

inspection or repair from the dealer where you purchased the unit or from qualified Yamaha

service personnel.

• Be careful not to drop or apply strong impact to this unit. If you suspect the unit may have

been damaged due to dropping or impact, immediately turn off the power and pull the power

plug from the AC outlet. Failure to observe this may cause electric shocks, a fire, or

malfunctions. Immediately request an inspection from the dealer where you purchased the

unit or from qualified Yamaha service personnel.

CAUTION

This content indicates “risk of injury.”

Power supply/power cord

• Do not use an AC outlet where the power plug fits loosely when inserted. Failure to observe

this may cause a fire, electric shocks, or burns.

• When removing the electric plug from the unit or an AC outlet, always hold the plug itself

and not the cord. Pulling by the cord can damage it and cause electric shocks or a fire.

• Insert the power plug firmly all the way into the AC outlet. Using the unit when it is not

plugged in sufficiently can cause dust to accumulate on the plug, causing a fire or burns.

Installation

• Do not place the unit in an unstable position where it might accidentally drop or fall over and

cause injuries.

• Do not block this unit's ventilation holes (cooling slits). This unit has ventilation holes on the

side to prevent the internal temperature from becoming too high. Failure to observe this

may trap heat inside the unit, causing a fire or malfunctions.

• When installing this unit:

- Do not cover it with any cloth.

- Do not install it on a carpet or rug.

- Make sure the top surface faces up; do not install on its sides or upside down.

- Do not use the device in a confined, poorly-ventilated location.

Failure to observe the above may trap heat inside the unit, causing a fire or malfunctions.

Ensure that there is adequate space around the unit: at least 5 cm (2 in) on top, 5 cm (2 in)

on the sides, and 5 cm (2 in) on the rear.

• Do not install the unit in places where it may come into contact with corrosive gases or salt

air or places that have excessive smoke or steam. Doing so may result in malfunction.

• Before moving this unit, be sure to turn off the power switch and disconnect all connection

cables. Failure to observe this may damage the cables or cause you to trip and fall.

• For proper installation of the outdoor antenna, make sure to have it done by the dealer from

where you purchased the unit or by qualified service personnel. Failure to observe this may

cause the installation to fall and result in injury. Installation requires special skills and

experience.

Hearing loss

• Do not use the unit for a long period of time at a high or uncomfortable volume level, since

this can cause permanent hearing loss. If you experience any hearing loss or ringing in the

ears, consult a physician.

• Before connecting the unit to other devices, turn off the power for all devices. Also, before

turning the power of all devices on or off, make sure that all volume levels are set to the

minimum. Failing to do so may result in hearing loss, electric shock, or device damage.

• When turning on the AC power in your audio system, always turn on the unit LAST, to avoid

hearing loss and speaker damage. When turning the power off, the unit should be turned off

En 5

FIRST for the same reason. Failure to observe the above may cause hearing impairment or

speaker damage.

Maintenance

• Remove the power plug from the AC outlet before cleaning the unit. Failure to observe this

may cause electric shocks.

Handling caution

• Do not insert your hand or fingers into disk slot of this unit. Failure to observe this may

cause injury.

• Do not insert foreign materials such as metal or paper into disk slot of this unit. Failure to

observe this may cause a fire, electric shocks, or malfunctions. If foreign material gets into

the unit, immediately shut off the power and pull the power plug from the AC outlet and

request an inspection from the dealer where you purchased the unit or from qualified

Yamaha service personnel.

• Do not do the following:

- stand on or sit on the equipment.

- put heavy items on top of the equipment.

- place the equipment in a stack.

- apply unreasonable force to buttons, switches, input/output terminals, etc.

• Avoid pulling the connected cables to prevent injuries or damage to the unit by causing it to

fall.

• Do not operate the unit if the sound is distorting. Prolonged use in this condition could

cause overheating and result in fire.

Battery use

• Always replace all batteries at the same time. Do not use new batteries together with old

ones. Using new ones with old ones could cause a fire, burns, or inflammation due to fluid

leaks.

• Do not use batteries other than specified batteries. Doing so cause fire, burns, or

inflammation due to leakage.

• Do not mix battery types, such as alkaline batteries with manganese batteries, or batteries

from different makers, or different types of batteries from the same maker, since this can

cause a fire, burns, or inflammation due to fluid leaks.

• Keep batteries away from children. A child could accidentally swallow a battery. Failure to

observe this may also cause inflammation due to battery fluid leaks.

• Do not put in a pocket or bag, carry, or store batteries together with pieces of metal. The

battery could short, burst, or leak, causing a fire or injury.

• Always make sure all batteries are inserted in conformity with the +/- polarity markings.

Failure to do so might result in a fire, burns, or inflammation due to fluid leaks.

• When the batteries run out, or if the unit is not to be used for a long time remove the

batteries from the unit to prevent possible leakage of the battery fluid.

• When storing or discarding batteries, insulate the terminal area by applying tape, or some

other protection. Mixing them with other batteries or metal objects can cause a fire, burns,

or inflammation due to fluid.

NOTICE

Indicates points that you must observe in order to prevent

product failure, damage or malfunction and data loss.

Power supply/power cord

• If not using the unit for a long period of time, be sure to pull the power plug from the outlet.

Even if the [z](Standby/On) switch has been turned off (the screen display is off), a minute

current is still flowing.

Installation

• Do not use this unit in the vicinity of other electronic equipment, such as a TV, radio, or

mobile phone. Failure to observe this may cause this unit or the TV or radio to produce

noise.

• Do not use this unit in a location that is exposed to direct sunlight that becomes extremely

hot, such as near a heater, or extremely cold, or that is subject to excessive dust or

vibration. Failure to observe this may cause the unit's panel to become deformed, the

internal components to malfunction, or for operation to become unstable.

• Install this unit as far away from other electronic equipment as possible.

Digital signals from this unit may interfere with other electronic equipment.

• If using a wireless function, avoid installing this unit near metal walls or desks, microwave

ovens, or other wireless network devices.

Obstructions could shorten the transmission distance.

Connections

• If connecting external units, be sure to thoroughly read the manual for each unit and

connect them in accordance with the instructions.

Failure to properly handle a unit in accordance with the instructions could cause

malfunctions.

• Do not connect this unit to industrial units.

Digital audio interface standards for consumer use and industrial use are different. This unit

has been designed to connect to a consumer-use digital audio interface. Connections to an

industrial-use digital audio interface could not only cause this unit to malfunction, but could

also damage the speakers.

6 En

Handling

• Do not place vinyl, plastic, or rubber products on this unit. Failure to observe this may cause

discoloration or deformation in the panel of this unit.

• If the ambient temperature changes drastically (such as during unit transportation or under

rapid heating or cooling) and there is a chance condensation may have formed in the unit,

leave the unit for several hours without turning on the power until it is completely dry before

use. Using the unit while there is condensation can cause malfunctions.

Maintenance

• When cleaning the unit, use a dry, soft cloth. Using chemicals such as benzine or thinner,

cleaning agents, or chemical scrubbing cloths can cause discoloration or deformation.

Batteries

• Be sure to discard used batteries in accordance with local regulations.

About content in this manual

• The illustrations and screens in this manual are for instructional purposes only.

• The company names and product names in this manual are the trademarks or registered

trademarks of their respective companies.

• Software may be revised and updated without prior notice.

LASER SAFETY

This unit employs a laser. Due to possible eye injury, only a qualifi ed service person should remove

the cover or attempt to service this device.

DANGER

This unit emits visible laser radiation when open. Avoid direct eye exposure to beam.

When this unit is plugged into the wall outlet, do not place your eyes close to the opening of the disc

tray and other openings to look into inside.

CAUTION

Use of controls or adjustments or performance of procedures other than those specified herein may

result in hazardous radiation exposure.

The laser component in this product is capable of emitting radiation exceeding the limit for Class 1.

The model number, serial number, power requirements, etc., may be found on or near the

name plate, which is at the rear of the unit. You should note this serial number in the space

provided below and retain this manual as a permanent record of your purchase to aid

identification in the event of theft.

Model No.

Serial No.

(rear_en_01)

En 7

Introduction

Confirm the package contents and useful points of this manual.

About this manual

• How to operate this unit is described mainly using the remote control.

• Illustrations may differ from actual item depicted.

• Symbols:

Caution Indicates information that should be read before use to prevent failure

or physical damage.

Note Indicates precautions and supplementary information that should be

read before using the unit.

& References another page or pages that provide additional information.

Trademarks

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and

any use of such marks by Yamaha Corporation is under license. Other trademarks and trade

names are those of their respective owners.

Yamaha Eco-Label is a mark that certifies products of high environmental performance.

Accessories

Remote control FM antenna Batteries (x 2)

(AA, R6, UM-3)

8 En

What you can do with this unit

Greater music

enjoyment

The unit is equipped with a

digital optical input jack and a

stereo mini-jack that enable

connection to external devices.

(& p. 21 Playing music from

external devices)

Bluetooth makes it easy

to operate remotely

The unit turns on automatically when

a Bluetooth connection is established.

(& p. 18 Playing music via Bluetooth®

connection)

Compact and easy to

use with high quality

sound

Sound quality can be adjusted to

suit individual preferences.

(& p. 23 Adjusting sound quality)

En 9

Parts name

Familiarize yourself with all parts and their functions.

Front panel

A B094 85 6 7321

1 z (Power) (& p. 15)

The front panel display turns on when the unit is turned on.

2 PHONES

Connect headphones to this jack.

Note

When headphones are connected, there is no sound from the

speakers or subwoofer.

3 USB jack (& p. 17)

4 f/h, j/g (& p. 16, 17)

PRESET

<

/

>

(& p. 19)

5 a/d (Play/pause) (& p. 16, 17)

6 s (Stop) (& p. 16, 17)

7 INPUT (& p. 16, 17)

Change the input source. (The selected input source is shown in the

front panel display.)

8 Disc tray (& p. 16)

9 VOLUME

Adjust the volume.

0 = (Open/close the disc tray) (& p. 16)

A Front panel display (& p. 11)

B Remote control sensor

10 En

Parts name

Rear panel

SPEAKERS

RL

DIGITAL IN

ANTENNA

FM75Ω

UNBAL.

AUX IN

SUBWOOFER

OUT

6Ω MIN./SPEAKER

+

–

71 32 4 5 6

1 Power cord (& p. 15)

2 Service only jack

Use when the unit requires maintenances.

3 DIGITAL IN jack (optical input) (& p. 21)

4 AUX IN jack (mini jack input) (& p. 21)

5 SUBWOOFER OUT jack (& p. 13)

6 ANTENNA jack (& p. 14)

7 SPEAKERS terminals (& p. 13)

En 11

Parts name

Front panel display

1 Multi information display

Show various information, such as music information and

the radio frequency.

Characters shown in the front panel display are

alphanumerics only.

2 TUNED indicator

Glows when the unit is receiving a signal from an FM

station.

3 STEREO indicator

Glows when the unit is receiving a signal from an FM

stereo broadcast.

4 MUTE indicator

Glows when the sound is muted (& p. 12).

5 SLEEP indicator

Glows when the sleep timer is set (& p. 15).

6 Shuffle/repeat indicator

Glows when the shuffle or repeat function is enabled for

songs in a CD or USB memory device.

7 $ Bluetooth indicator

Show the status of Bluetooth connection.

Note

Changing display brightness

Each press of the DIMMER button on the remote control

(& p. 12) changes the brightness: bright (default), mid dim, or

dim.

aaaaaaaa

aaaaaaaaaaaaaaaa

TUNED

STEREO

MUTE

SLEEP

ALL

1

vx

$

1 2 3 4 5 6 7

12 En

Parts name

Remote control

1 Infrared signal transmitter

2 OPEN/CLOSE = (Open/close the disc tray)

(& p. 16)

3 Input source buttons

Switch the input source.

4 Numeric buttons (& p. 16)

5 SHUFFLE (& p. 22)

6 BASS, TREBLE (& p. 23)

7 Audio control, cursor control buttons (& p. 16,

17)

8 OPTION (& p. 24)

9 VOLUME +/–

Adjust the volume.

0 TUNER/PRESET (& p. 19)

A SLEEP (& p. 15)

B DIMMER (& p. 11)

C z (Power) (& p. 15)

D REPEAT (& p. 22)

E MUTE

Turn mute on or off.

F DISPLAY (& p. 23)

Installing batteries

Check the “+” and “-” of the batteries and insert them in the

correct directions.

Note

Change both batteries when the operation range of the

remote control decreases.

1

C

D

E

F

2

3

4

5

6

7

8

9

0

A

B

En 13

Preparations

Connect speakers, the antenna, etc. and turn the unit on.

Do not connect the power cord of the unit until you have finished connecting all cables.

Connecting speakers

1 Remove the insulation from the ends

of the speaker cables to expose the

bare wires.

2 Connect speakers to the unit, as the

illustration shows.

• Prepare speakers, subwoofer and speaker cables

separately.

• See documentation provided with the speakers

for more information.

Caution

• If the bare speaker wires touch each other or any metal part of the unit, it could damage the unit and/or the speakers.

• Use speakers of at least 6 Ω impedance.

Note

• Make sure that left and right (L, R) connections and polarity (red: +, black: -) are correct. If connections are incorrect, the sound will

be unnatural.

• You can also connect a subwoofer to the unit (it must have a built-in amplifier).

15 mm (5/8 in.)

1

3

2

SUBWOOFER

OUT

Right speaker

Left speaker

Subwoofer

Monaural pin cable

Speaker cable

14 En

Preparations

Connecting the antenna

1 Connect the supplied antenna to the

unit.

2 Install it with pins where the unit can

obtain good reception.

Note

• Be sure to stretch out the antenna as the illustration shows.

• If radio reception with the supplied antenna is not satisfactory, an outdoor antenna (sold separately) may improve reception.

ANTENNA

FM75Ω

UNBAL.

Supplied antenna

2

1

En 15

Preparations

Turning on the power

Plug the power cord into a power outlet, and press z.

• The unit turns on.

• Press z again to turn the unit off (standby mode).

Using the sleep timer

You can set the time after which the unit automatically enters standby mode. The time can

be selected from 120/90/60/30 min., or OFF.

Press SLEEP repeatedly to select the time.

The SLEEP indicator lights up when the sleep timer is set.

Note

• To cancel the sleep timer, press SLEEP again.

Reducing power consumption

Auto standby

The unit will automatically enter standby mode (auto standby) if in any of the following

situations:

• BLUETOOTH, CD, or USB is selected as the input source, but no audio is played, and no

operations are performed, for more than 20 minutes.

• An input source other than above is selected, but no operations are performed for

more than 8 hours.

See “Option menu” (& p. 24) to disable the auto standby function.

Eco standby

The unit minimizes power consumption in eco standby mode. Disable the BT Standby

(Bluetooth standby) function to enable eco standby (& p. 24).

1

2

Within 6 m (20 ft)

SLEEP

16 En

Listening to music

Listening to CDs

1 Press CD on the remote control.

2 Set a CD in the disc tray.

Press = to open/close the disc tray.

3 Press a/d.

Playback starts.

Use the following buttons to control audio playback. A song

can also be selected using the numeric buttons on the

remote control.

Note

• This unit allows playback of audio CDs, and data CDs in which MP3/

WMA files are recorded. For details on playable CDs, see “Supported

devices/media and file formats” (& p. 30).

• When CD playback is stopped, playback will resume from the

beginning of the song last played. Pressing s (stop) while

playback is stopped will clear resume playback.

• You can cancel the song number selected with the numeric

buttons by pressing s (stop).

• Music files stored on a data CD can be played using the same

operations used to play music stored on a USB memory device

(& p. 17).

• If you turn off the unit with CD selected as the input source and a

CD set in it, the unit automatically plays back the set CD next time

you turn on the unit.

a/d Play/pause

s Stop

f

Skip to the beginning of the song being

played back. Press and hold to fast rewind.

g

Skip to the next song. Press and hold to fast

forward.

SHUFFLE/

REPEAT

& p. 22

SHUFFLE

g

s

f

REPEAT

CD

a

/

d

En 17

Listening to music

Playing music on USB memory devices

1 Press USB on the remote control.

2 Connect a USB memory device to the USB

jack.

3 Select a song.

Use the following buttons to control audio playback.

Note

• This unit allows playback from USB memory devices on which

music files are saved. For details on playable USB memory devices,

see “Supported devices/media and file formats” (& p. 30).

• Some USB memory devices may not work properly even if they

meet the requirements. Playability of and power supply to all USB

memory devices are not guaranteed.

• Stop playback before disconnecting the USB memory device.

• A USB memory device is automatically charged as long as it is

connected to the unit except when the unit is in standby mode.

However, some devices may not charge when connected.

• Connect a USB storage device directly to the USB jack of the unit. Do

not use extension cables.

q

w

Select a folder.

a/d,

g

Confirm the selected item and proceed to

the next level, or start/pause playback.

f Return to the previous item.

s Stop

SHUFFLE/

REPEAT

& p. 22

DISPLAY

Display information about the content

being played (& p. 23).

SHUFFLE

g

q

/

w

a

/

d

s

f

REPEAT

USB

DISPLAY

18 En

Listening to music

Playing music via Bluetooth® connection

1 Enable the Bluetooth function on your

Bluetooth device.

2 Press BLUETOOTH on the remote control.

3 Select this unit from the Bluetooth device

list on your Bluetooth device.

The $ indicator glows when a connection is established.

4 Play music using your Bluetooth device.

Note

• Decrease the volume of the unit before playback. Otherwise,

playback volume may be too loud.

• If a Bluetooth device has been connected before, the unit will

connect to the last connected device when BLUETOOTH on the

remote control is pressed.

• If the unit is connected to another device via Bluetooth connection,

press and hold BLUETOOTH at least three seconds to terminate that

connection before connecting to the target device.

• If a passkey is required during the Bluetooth connection, enter the

number “0000.”

• See documentation provided with your Bluetooth device for more

information on Bluetooth connection.

Unable to connect the unit to a Bluetooth device

If a Bluetooth connection was not established after following the

instructions shown at left, try the following.

1 If the Bluetooth device has been connected to the unit before,

delete the unit from the list of devices registered with your

Bluetooth device.

2 Press and hold BLUETOOTH on the remote control for at least

three seconds.

- “Pairing” will be shown in the front panel display.

3 Select this unit from the Bluetooth device list on your Bluetooth

device.

- The $ will glow in the front panel display when a connection is

established.

Bluetooth device

This unit

$

BLUETOOTH

En 19

Listening to music

Listening to FM radio stations

Connect the antenna supplied with the unit (& p. 14) to receive FM stations.

1 Press TUNER.

2 Press and hold ee or rr until automatic

tuning starts.

Automatic tuning stops when a station is tuned in.

Note

• If station reception is weak, tune into a station manually by pressing

ee /rr repeatedly. Sound will be heard in monaural.

Auto preset

The unit tunes in stations with good reception and presets them

automatically.

1 Press TUNER.

2 Press and hold MEMORY at least two

seconds.

3 Press MEMORY.

Auto preset starts, and when it finishes, “Completed!” is

shown in the front panel display.

Note

• Auto preset replaces all stations currently stored with new stations.

• Up to 30 FM stations can be preset.

• Press s to cancel Auto preset.

Tuning in FM stations

FM

87.50MHz

TUNED

STEREO

Presetting FM stations

TUNER

s

ee /rr

MEMORY

20 En

Listening to music

Manual preset

1 Tune into a station you want to preset

(& p. 19).

2 Press MEMORY.

The preset number flashes in the front panel display.

3 Press q/w to select the desired preset

number.

4 Press a/d to preset the station.

Note

• To cancel manual preset setting, press s.

1 Press TUNER.

2 Press e/r to select a station.

The number of a registered preset can also be selected using

the numeric buttons.

Note

Deleting a preset station

1 Press and hold DELETE at least two seconds when FM is selected

as the input source.

- The preset number flashes in the front panel display.

2 Press q/w to select the preset number of the station to be

deleted.

3 Press a/d.

- The station in the selected preset number is deleted.

Memory

FM01 87.50MHz>

Selecting preset FM stations

TUNER

s

q

/w

a

/

d

MEMORY

DELETE

e/r

Страница загружается...

Yamaha CRX-B370, CD Receiver Инструкция по применению

Похожие модели бренда