ZyXEL NWA-3166 Инструкция по началу работы

www.zyxel.com

Wireless N Dual-Band

Business WLAN Access Point

Firmware v3.60

Edition 3, 02/2009

NWA-3166

DEFAULT LOGIN DETAILS

IP Address: http://192.168.1.2

Password: 1234

CONTENTS

ENGLISH 3

DEUTSCH 15

ESPAÑOL 31

FRANÇAIS 45

ITALIANO 59

РУССКИЙ 73

SVENSKA 87

简体中文

99

繁體中文

111

ZyXEL Communications Corporation

2

ENGLISH

3

Overview

This Quick Start Guide shows how to set up and configure the NWA (marked Z in the

figure) to allow wireless clients to securely access your wired network. See your User’s

Guide for more information.

" The icon used in this Quick Start Guide is not an exact representation of

your NWA.

At the time of writing this Quick Start Guide covers the following models:

• NWA-3166 Wireless N Dual-Band Business WLAN Access Point

" You may need your Internet access information.

To set up your wireless network you need to:

1 Connect the Hardware

2 Access the Web Configurator

3 Configure the NWA

4 Install the Hardware

5 Set Up Power over Ethernet (Optional)

ENGLISH

4

1 Connect the Hardware

" The figures and screens shown in this Quick Start Guide are from the NWA-

3166. Your device may differ in minor ways.

1 Using the grey Ethernet cable, connect the ETHERNET port to a computer for initial

configuration.

2 Connect the POWER 12VDC socket to a power source using only the included power

adaptor.

" Connect the NWA’s ETHERNET port to an Ethernet jack with network

access after you have completed the initial configuration.

ENGLISH

5

1.1 LEDs

•The PWR/SYS LED turns steady green when the power is connected.

•The ETHN LED turns on if the ETHERNET port is properly connected, and blinks when

there is traffic. The LED turns green if the connection is at 10Mbps, and turns yellow if the

connection is at 100Mbps.

V If the ETHN LED does not turn on, check the cable connection to the

NWA’s ETHERNET port. Ensure your computer’s network card is working

properly.

2 Access the Web Configurator

" Use Internet Explorer 6.0 and later or Firefox 2.0 and later versions with

JavaScript enabled and pop-up blocking disabled.

2.1 Set Up Your Computer’s IP Address

" Note down your computer’s current IP settings before you change them.

ENGLISH

6

First, set your computer to use a static IP address in the 192.168.1.3 - 192.168.1.254

range with a subnet mask of 255.255.255.0. This ensures that your computer can

communicate with your NWA. See your User’s Guide for information on setting up your

computer’s IP address.

2.2 Log Into the Web Configurator

" Even though you can connect to the NWA wirelessly, it is recommended

that you connect your computer to the ETHERNET port for initial

configuration.

1 Launch your web browser. Enter

192.168.1.2 (the NWA’s default IP

address) as the address.

V If you cannot access the Web configurator, make sure the IP addresses

and subnet masks of the NWA and the computer are in the same IP

address range (see Section 2.1).

2 Click Login (the default password

1234 is already entered).

ENGLISH

7

3 Change the login password by

entering a new password and

clicking Apply. Be sure to record the

new password and keep it in a safe

place.

V If you change the password and then forget it, you will need to reset the

NWA. Refer to the User’s Guide for how to use the RESET button.

4 Click Apply to replace the factory

default certificate for added security;

alternatively click Ignore to proceed

if you do not want to change the

certificate now.

5 The STATUS screen appears.

ENGLISH

8

3 Configure the NWA

3.1 Configure System Settings

1 Click SYSTEM in the navigation panel.

2 The SYSTEM > General screen appears.

System Name is for identifying the NWA on your network. Choose a distinctive name,

or leave this at its default.

Domain Name: Enter a domain name if your ISP requires one for authentication.

Otherwise you can leave it blank or set to whatever may have displayed automatically.

DNS Server(s): if your ISP gave you specific DNS (Domain Name System) settings,

select User-Defined and enter them here. Otherwise, leave these fields at their defaults.

3 Click Apply.

ENGLISH

9

Configure Wireless Settings

1 Click WIRELESS in the

navigation panel. A

screen similar to the

following appears. Not all

fields are available in all

models.

" The wireless stations and the NWA must use the same SSID,

channel ID and encryption settings for wireless communication.

Operating Mode: Ensure that Access Point mode is selected.

802.11 Mode: Select the wireless standard you want your network to use. If you are

not sure which to select, select 802.11b+g.

Channel Width (802.11n/g, 802.11n/a mode only): Select the channel bandwidth

you want to use. If you are not sure, select 20/40 MHz.

Channel ID: Select the wireless channel you want your network to use. To have the

NWA automatically select a channel, click Scan instead.

Short GI (802.11n/g, 802.11n/a mode only): Select Enable if your wireless clients

support the short guard interval. If you are not sure, select Disable.

A-MPDU Aggregation (802.11n/g, 802.11n/a mode only): Select Enable if your

wireless clients support the Aggregated MAC Protocol Data Unit standard. If you are

not sure, select Disable.

ENGLISH

10

RTS/CTS Threshold: Sends an RTS for all packets larger than the number (of

bytes) that you enter here. If you are not sure, leave it as the default.

Fragmentation Threshold: Enter an even number between 256 and 2346. This is

the maximum data fragment size that can be sent. If you are not sure, leave it as the

default.

Beacon Interval: Enter a value from 30ms to 1000ms. This tells receiving devices

on the network how long they can wait in low-power mode before waking up to

handle an incoming beacon. If you are not sure, leave it as the default.

DTIM: Enter a value from 1 to 100. This is the time period after which broadcast and

multicast packets are transmitted to mobile clients in the Active Power Management

mode. If you are not sure, leave it blank.

Output Power: Select the relative strength of your NWA’s broadcast output. If the

area in which it is located has a high number of APs, reduce the output power to

reduce interference from those other devices. Reducing the output power similarly

reduces the broadcast radius.

SSID Profile: Select the SSID profile you want to configure for network access from

the drop-down list box. This example uses the SSID03 profile.

2 Click Apply to save your settings.

3 Click the SSID tab. The

following screen appears.

Ensure the settings for

SSID03 are at their default

values.

The default SSID (the

name of the network) is

ZyXEL03, its default

Security setting is

Security01. Layer 2

Isolation and MAC Filter

are set to Disable by

default.

If you want to change the

SSID profile’s settings,

select SSID03 and click

Edit.

ENGLISH

11

4 Click the Security tab.

Ensure that Security01 is

selected and click Edit.

If you don’t configure

wireless security, then

anyone can access your

network.

5 This is where you can

enter the security settings

for your wireless network.

The fields you fill in differ

according to the type of

security you select in the

Security Mode field.

Select None if you do not

wish to use wireless

security.

This example uses WPA2-

PSK security, in which all

wireless clients must use

the same pre-shared key

to join the network.

Ensure that all your

wireless clients support the

type of security you set.

Click Apply when you

have finished.

V If the wireless clients cannot communicate with the network, ensure

that the clients and the NWA are using the same wireless security

settings.

ENGLISH

12

3.2 Configure IP Settings

The NWA is now ready to connect to your switch or router. You can do this now, or once

you have attached the antennas and mounted the NWA.

V If the NWA cannot communicate with the network, ensure that the NWA is

using an IP address on the same subnet as the switch / router.

1 You need to set your NWA’s IP

address to be in the same

subnet as your network. Click

IP in the navigation panel.

Select Get automatically from

DHCP if you want to have a

DHCP server on your network

assign an IP address to the

NWA.

If you have a specific IP address

to use, select Use fixed IP

address and enter it along with

the subnet mask and gateway

IP address.

Click Apply. The NWA now

uses the new IP settings; you

can no longer connect to the

NWA using the default IP

address.

" If you change the NWA’s IP address, you must use the new IP address

when you next access the web configurator. If you select Get

automatically from DHCP, check your DHCP server to determine the IP

address it assigns to the NWA. Refer to your DHCP server’s

documentation for more information.

2 If you changed your computer’s IP address in Section 2.1, return it to its previous

setting.

3 Change the wireless settings in the wireless stations to match those of the NWA.

Refer to your wireless adapter’s documentation.

ENGLISH

13

4 Install the Hardware

Figures in this section use generic icons. The ZyXEL Device in the picture is not an exact

representation of your device.

In general, the best location for the access point is at the center of your intended wireless

coverage area. For better performance, mount the NWA high up in an area that is free of

obstructions.

Wall-mounting

Do the following to attach your NWA to a wall.

1 Screw the two screws provided with your NWA into the wall 140mm apart (see the

figure in step 3). Use screws with 6mm ~ 8mm (0.24" ~ 0.31") wide heads. Do not

screw the screws all the way in to the wall; leave a small gap between the head of the

screw and the wall.

The gap must be big enough for the screw heads to slide into the screw slots and the

connection cables to run down the back of the NWA.

" Make sure the screws are securely fixed to the wall and strong enough to

hold the weight of the NWA with the connection cables.

2 Align the holes on the back of the NWA with the screws on the wall. Hang the NWA on

the screws.

" You can also use the optional Ceiling Mount Kit (sold separately) to mount

the NWA on a ceiling instead of a wall.

1

4

0

m

ENGLISH

14

5 Set Up Power over Ethernet (Optional)

Power over Ethernet (PoE) is the ability to provide power to your NWA via an 8-pin CAT 5

Ethernet cable, eliminating the need for a nearby power source.

A PoE injector (not included) is also needed to supply the Ethernet cable with power. This

feature allows increased flexibility in the location of your NWA.

In the following figure, Z is your NWA, A is the CAT 5 Ethernet cable, B is the PoE injector

and C is the power cable.

" You can connect the NWA to PoE via the ETHERNET port AND to a power

source via the POWER 12VDC port. If you do so, do not disconnect the

ETHERNET port before you disconnect the POWER 12VDC port. This

causes the NWA to restart.

6 Procedure to View a Product’s Certification(s)

1 Go to www.zyxel.com.

2 Select your product from the drop-down list box on the ZyXEL home page to go to that

product's page.

3 Select the certification you wish to view from this page.

DEUTSCH

15

Übersicht

In dieser Kurzanleitung erfahren Sie, wie das NWA (im Beispiel unten mit einem Z

gekennzeichnet) installiert und konfiguriert wird, damit Wireless-Clients sicher auf Ihr

kabelgebundenes Netzwerk zugreifen können. Weitere Informationen finden Sie im

Benutzerhandbuch.

" Das in dieser Kurzanleitung abgebildete Gerät kann unter Umständen

leicht von Ihrem NWA abweichen.

Zum Zeitpunkt der Druckstellung umfasst die Kurzanleitung die folgenden Modelle:

• NWA-3166 Wireless N Dual-Band Business WLAN Access Point

" Halten Sie die Daten für Ihren Internetzugang bereit.

Um das Drahtlosnetzwerk einzurichten, müssen Sie:

1 Die Hardware anschließen.

2 Auf den Web-Konfigurator zugreifen.

3 Den Internetzugriff konfigurieren.

4 Die Hardware installieren.

5 Power-over-Ethernet einrichten (optional).

DEUTSCH

16

1 Anschließen der Hardware

" Das in dieser Kurzanleitung abgebildete Gerät ist der NWA-3166. Die

Bildschirmdarstellungen sind ebenfalls von diesem Gerät entlehnt. Ihr

Gerät kann von diesen Abbildungen leicht abweichen.

1 Verbinden Sie für die Erstkonfiguration den ETHERNET-Anschluss mit dem grauen

Ethernet-Kabel mit dem Computer.

2 Verbinden Sie die 12VDC-Netzanschlussbuchse POWER des Geräts mit dem

mitgelieferten Netzadapter mit dem Stromnetz.

DEUTSCH

17

" Nachdem Sie die Erstkonfiguration durchgeführt haben, verbinden Sie den

ETHERNET-Anschluss des NWAs mit einem Ethernetanschluss mit

Netzwerkverbindung.

1.1 LED-Anzeigen

• Die LED-Anzeigen PWR/SYS und LED beginnen grün zu leuchten, sobald das Gerät mit

Strom versorgt wird.

• Die LED-Anzeige ETHN beginnt zu leuchten, wenn der ETHERNET-Anschluss richtig

angeschlossen ist, und sie blinkt, wenn Daten übertragen werden. Die LED-Anzeige

leuchtet bei einer 10-Mbps-Verbindung grün und bei einer 100-Mbps-Verbindung gelb.

V Wenn die ETHN-LED nicht leuchtet, prüfen Sie die Kabelverbindung am

ETHERNET-Port des NWAs. Stellen Sie sicher, dass die Netzwerkkarte

des Computers installiert ist und einwandfrei funktioniert.

DEUTSCH

18

2 Zugreifen auf den Web-Konfigurator

" Verwenden Sie den Internet Explorer 6.0 oder den Firefox 2.0 und neuere

Versionen davon mit aktiviertem JavaScript und aktivierter Pop-up-

Funktion.

2.1 Einrichten der IP-Adresse des Computers

" Notieren Sie sich die aktuellen IP-Einstellungen des Computers, bevor Sie

sie ändern.

Richten Sie den Computer zunächst so ein, dass er eine statische Adresse im Bereich

192.168.1.3 bis 192.168.1.254 mit der Subnetz-Maske 255.255.255.0 verwendet. Nur auf

diese Weise kann Ihr Computer mit dem NWA kommunizieren. Informationen zum

Einrichten der IP-Adresse des Computers finden Sie im Benutzerhandbuch.

2.2 Anmelden beim Web-Konfigurator

" Auch wenn Sie eine drahtlose Verbindung zum NWA herstellen können,

wird empfohlen, das Gerät für die Erstkonfiguration über den ETHERNET-

Anschluss an den Computer anzuschließen.

1 Starten Sie Ihren Webbrowser.

Geben Sie als Adresse 192.168.1.2

(die Standard-IP-Adresse des

NWAs) ein.

V Wenn Sie nicht auf den Web-Konfigurator zugreifen können, prüfen Sie,

ob die IP-Adressen und Subnetz-Masken des NWAs und des Computers

im selben IP-Adressbereich liegen (siehe Abschnitt 2.1).

DEUTSCH

19

2 Klicken Sie auf Login (Anmelden)

(das Standardkennwort 1234 ist

bereits vorgegeben).

3 Ändern Sie das Kennwort, indem Sie

ein neues Kennwort eingeben und

auf Apply (Übernehmen) klicken.

Notieren Sie sich das neue Kennwort

und bewahren Sie die Notiz an

einem sicheren Ort auf.

V Wenn Sie das neue Kennwort vergessen haben, muss das NWA

zurückgesetzt werden. Lesen Sie im Benutzerhandbuch nach, wie die

RESET-Taste verwendet wird.

4 Klicken Sie auf Apply

(Übernehmen), um das werkseitig

eingerichtete Standardzertifikat für

zusätzliche Sicherheit zu ersetzen.

Sie können jedoch auch auf Ignore

(Ignorieren) wenn Sie das Zertifikat

jetzt nicht ändern möchten.

DEUTSCH

20

5 Das STATUS-Fenster erscheint.

Страница загружается...

ZyXEL NWA-3166 Инструкция по началу работы

Похожие модели бренда